NIBE VVM 300. Intelligent hot water NIBE VVM 300. VVM 300 is designed for connection and communication
|
|
- Clarence Fitzgerald
- 5 years ago
- Views:
Transcription
1 NIBE VVM 300 all in one indoor unit Intelligent hot water VVM 300 is designed for connection and communication with outdoor heat pump F20XX of 6 kw, 8 kw and 10 kw. Water volume 280 litres, of which 155 litres is hot tap water. VVM 300 is equipped with climate controlled automatic bypasses to maintain the correct temperature for the heating system. Unique control system for maximum energy optimization. Self regulating speed controlled charge pump. Load monitor as standard for house fuse. Prepared for pool heating. Prepared for control of two heating systems. NIBE VVM 300 NIBE VVM 300 is an all in one inddor unit. It consists of a double jacketed pressure vessel, two immersion heaters and intelligent controls. VVM 300 is designed for connection and communication with outdoor heat pump F20XX of 6 kw, 8 kw and 10 kw. For example floating condensation and automatic speed control for optimal performance of the load pumpconnected to the outdoor unit. VVM 300 is equipped with an intelligent control. The insulation consists of environmenal friendly polyurethane, which is moulded in one piece.
2 good to know about NIBE VVM 300 Transport and storage NIBE VVM 300 must be transported and stored upright and dry. The VVM 300 may, however, be carefully laid on its back when being moved into a building. Maintenance Great importance has been placed on the design of the control panel to achieve the most simple operation possible. A minimum level of maintenance is required. Only safety valves require checking. All essential components can be accessed from the front. This facilitates service and maintenance. Erecting the heat pump Electric boiler ideally located in utility room or boiler room. The unit can be aligned using the adjustable feet. Route pipes so they are not fixed to an internal wall that backs on to a bedroom or living room. The minimum ceiling height is 2.0 m. Equipment VVM 300 is equipped with a complete set of valves, consisting of a drain valve, filling valve, vacuum valve, non-return valve, and safety valve for the water heater section. The boiler section is equipped with a drain valve, filler valve and safety valve. In addition, the unit is equipped with climate controlled automatic bypasses with outdoor and flow sensors, shunt valve, circulation pump and expansion vessel. Hot water temperature We recommend you to use the VVM 300 in combination with F2026 for heating systems up to max 55 C the coldest day. 2 NIBE VVM 300
3 good to know about NIBE VVM 300 Dimensions Required space for removing the front cover. 70 A Adjustable Ställbar C * 35 *Free height for pipe and cable routing from rear B A, B and C: See Setting out dimensions in List of components. NIBE VVM 300 3
4 2 1 bar Art.nr. 611??? good to know about NIBE VVM 300 Component locations Warm v.v. water Cold k.v. Återledn. Return water radiatorer line radiator circuit Framledning Supply line radiatorer radiator circuit 4 NIBE VVM 300
5 good to know about NIBE VVM 300 List of components 1 Immersion heater 9 kw 2 Load monitor card 3 Operating thermostat, backup heating 4 Communication socket, communication cable F20XX 6 Temperature limiter 7 Miniature circuit-breaker 8 Switch, position Terminal block, power supply 10 Contactor, electrical step III, 6 kw 11 Terminal block, contactors 12 Terminal block, three way valve, charge pump 14 Terminal block 15 Outside sensor 16 Circulation pump, heating medium 17 venting screw, circulation pump 18 Pushbutton, Extra hot water 19 Shunt motor with handwheel 23 Adjustable feet mm 24 Immersion heater 4.5 kw 25 Push button Operating mode 30 No function 32 Display unit 33 Fine wire fuse 34 CPU-unit, control system 35 Capacity setting, circulation pump 38 Knob, Offset heating curve 40 Charge pump 42 Pressure gauge, boiler 43 Shunt valve 44 Shutoff valve, pump and flow line radiator circuit 45 Mixer valve 46 Filler valve, hot water heater 47 Safety valve, hot water heater 48 Cartridge non-return valve (hidden) 49 Combined filling and non-return valve, heating system 50 Shutoff valve, return line radiator circuit 51 Drain valve, heating system 52 Safety valve, heating system 53 Vacuum valve 61 Motor, three way valve 62 Shuttle valve 66 Rating plate 67 Contactor, electrical step I, 3 kw 69 Contactor, electrical step III, 4.5 kw Connection Setting out dimensions A B C 70 Supply line, radiator circuit From below, compression ring Ø 22 mm Return line, radiator circuit From rear, compression ring Ø 22 mm Cold water connection From below, compression ring Ø 22 mm Hot water outlet from hot water heater From below, compression ring Ø 22 mm Docking, incoming from F 2020 From rear, compression ring Ø 22 mm Docking, outgoing to F 2020 From rear, compression ring Ø 22 mm Venting, heating medium 79 Drain and overflow water connection, hot water heater R 15 male (with compression ring not removed) 80 Drain connection, heating system R 15 male 83 Temperature sensor, hot water 84 Shut-off valve, charge pump 85 Expansion vessel 88 Temperature sensor, immersion heater operation 89 Temperature sensor, supply line 93 Temperature sensor, return 95 Overflow pipe, safety valve hot water heater 96 Overflow pipe, safety valve heating 98 Overflow water discharge PVC-pipe Ø 32 mm (outside diameter) 99 Overflow cup, waste water 100 Knob, setting Fuse 101 Knob, setting Max electrical output 102 Knob, Max boiler temperature setting 103 Serial number 104 Communication card 162 Control card, charge pump 163 Cable, electrical supply, 2 2,5 m NIBE VVM 300 5
6 installation VVM 300 is easy to install. All pipe connections are easily accessible. This is especially useful for the replacement market. Pipe installation All pipe connections are equipped with 22 mm compression ring couplings. Radiator connection Radiator circuit connects to terminal (70), flow line and terminal (71), return line. In units where the radiator flow can completely stop due to all thermostat valves being in the closed position, bypass valves must be installed to protect the circulation pump. Tap water connection Hot and cold water are connected to terminal (74) mixed water and (73) (cold water). The electric boiler can be supplemented with an extra hot water heater if a bubble pool or other significant consumer of hot water is installed. Docking connection Docking connection from F20XX is connected to terminal (75). Docking connection to F20XX is connected to terminal (76). Recommended dimension of charge circuit is min Ø28 mm. Inspection of the installation Current regulations require the heating installation to be inspected before it is commissioned. The inspection must be carried out by a suitably qualified person and should be documented. The above applies to installations with a closed expansion vessel. If the electric boiler or the expansion vessel is replaced, the installation must be inspected again. Maximum boiler and radiator volumes The volume of the expansion vessel (85) is 12 litres and it is pressurised as standard to 0.5 bar (5 mvp). As a result, the maximum permitted height between the vessel and the highest radiator is 5 metres. If the standard initial pressure in the pressure vessel is not high enough it can be increased by adding air via the valve in the expansion vessel. The initial pressure of the expansion vessel must be stated in the inspection document. Any change in the initial pressure affects the ability of the expansion vessel to handle the expansion of the water. Pump capacity diagram Heating medium pump Heat regulation Sunlight and heat emissions from people and household machines are normally sufficient to keep the house warm during the warmer parts of the year. When it gets colder outside, the heating system must be started. The colder it is outside, the warmer radiators and floor heating system must be. Control of the heat production is performed based on the floating condensing principle, i.e. the temperature level needed for heating at a specific outdoor temperature is produced guided by collected values from the outdoor and flow sensors. As an option, room sensors can also be used to compensate for variations in room temperature. The supply of heat to the house is regulated in accordance with the chosen setting of the regulating curve (curve slope and offset). After adjustment, the correct amount of heat for the outside temperature is supplied. The flow temperature (menu 2.0) will hover around the theoretical required value (the value in brackets on the display). For subnormal temperatures the control system calculates a heating deficit in the form of degreeminutes, which means that heating production is accelerated. The larger the subnormal temperature, the greater the heat production. There are 8 stages to heat production, one for the heat pump and 7 for the electrical module. Available Tillgängligt pressure, tryck, kpa kpa Charge pump Available Tillgängligt pressure, tryck, kpa kpa Max flow: 1700 l/h Max flöde: 1700 l/h kpa Flow Flöde l/h 0 0,1 0,2 0,3 0,4 0,5 l/s kpa % 60 90% 50 70% % 20 30% 10 10% Flow Flöde l/h 0 0,1 0,2 0,3 0,4 l/s 6 NIBE VVM 300
7 Installation Electrical connections Connection VVM 300 must be installed via an isolator switch with a minimum breaking gap of 3 mm. Other electrical equipment, except the outdoor sensor and the current sensors, are connected at the factory. Disconnect the electric boiler before insulation testing the house wiring. Connection must not be carried out without the permission of the electricity supplier and under the supervision of a qualified electrician. The cable entry conduit is dimensioned for cable with a max Ø 19 mm. The power is controlled via contactors, which are operated by a the control system. The automatic heating control system, circulation pump (16), charge pump (40) and its cabling, are internally fuse protected with a miniature circuit breaker (7). Outside sensor Install the outside sensor in the shade on a wall facing north or north-west, so it is unaffected by the morning sun. Connect the sensor with a two wire cable. If a conduit is used it must be sealed to prevent condensation in the sensor capsule. The minimum cable cross section should be 0.4 mm2 up to lengths of 50 metres, for example, EKKX or LiYY. Centralised load control and load monitor Centralised load control or tariff control achieved by activation of external potential free closing contact. VVM 300 is equipped with an internal load monitor. The control system must be set for the installation s main fuse so that the load monitor can work correctly. The supplied current sensor (20) is connected to VVM 300 by a 4 wire cable. Cable type: unscreened LiYY, screened LiYCY. Cable area, at least 4 x 0.25 mm2 with cable length up to 50 m. When the load monitor senses an overcurrent on one of the phases, the immersion heater will step down the output until it can be connected again. Overview, electrical connection Outside Utegivare sensor Power supply Elmatning Isolator Arbetsbry switch Isolator Arbetsbrytare switch Power supply Elmatning Kommunikationskabel Communication cable Current Strömkänn sensor Any connected F20XX Eventuellt ansluten F20XX VVM 300 NIBE VVM 300 7
8 Dockings NIBE VVM 300 can be connected in several ways. Further option information is available at VVM 300 docked to F2XXX VVM 300, together with F2XXX, creates a complete heating and hot water unit. VVM 300 is equipped with a control box that currently makes it the most economical operator, regarding both for the integrated immersion heaters (max 13.5 kw) and compressor operation in F2XXX. VVM 300 comes complete with an automatic by-pass, three way valve, circulation pumps, and safety equipment. VVM is designed for simple connection to F2XXX. VVM 300 controls F2XXX, which runs with floating condensation towards the heating system. If F2XXX cannot meet the heating requirement, additional heat is shunted in from VVM 300. When the outside temperature drops below the set stop temperature VVM 300 engages and takes over the heating. RC UG F2XXX F20XX SÄV AV TV SF AV VVM NIBE VVM 300
9 Dockings VVM 300 docked with pool The installation can be supplemented with accessory POOL 20, to provide pool heating. Pool RC VVM 300 VVM 300 with extra shunt The unit can be supplemented with accessory ESV 20 for control of two heating systems at different temperatures, e.g. under floor heating and radiator system. RC 95 VVM 300
10 technical specifications Height (excl. foot: mm) Required ceiling height Width Depth Weight Volume total Volume double jacket Volume, hot water heater (CU) Volume, expansion vessel Supply voltage Max output immersion heater Supplied output immersion heater Rated output, circulation pump Rated output charge pump Enclosure class Design pressure, hot water heater Cut-off pressure, hot water heater Max permitted pressure in double jacket volume Design pressure in double jacket volume Pre-pressure expansion vessel 1,880 mm 2,000 mm 600 mm 615 mm 160 kg 280 litres 125 litres 155 litres 12 litres 400 V~ 3 NAC 50 Hz 13.5 kw 9.0 kw 45/75/110 W (adjustable) 6 70 W (speed controlled) IP MPa (10 bar) 0.9 MPa (9 bar) 0.25 MPa (2.5 bar) 0.25 MPa (2.5 bar) 0.5 bar (5 mvp) Adjustable max boiler temperature C Display languages English, Swedish, German, Danish, Czech, Finnish, French, Polish, Slovenian RSK No supplied components NIBE AB Utetemperatur givare Outdoor temperature sensor Aussentemperatur fühler Artikel Outdoor sensor Current sensors 10 NIBE VVM 300
11 GRUNDFOS DK GRUNDFOS Type UPS P/N: V- PC;0017NIB 50Hz 2.5uF IP TF Class H Max. 10bar Type UPS P/N: V- PC;0017NIB 50Hz 2.5uF IP TF Class H Max. 10bar 1m(A) P,(W) DK 1m(A) P,(W) HEJSAN HEJSAN HAHN VARNING Plåt med kopplingsplint ϒC Accessories 20 NIBE F2026 Air/water heat pump F Part no F Part no NIBE ESV 20 Extra shunt Used when there is a need of two different supply temperatures. Installed externally, but controlled from VVM 300. Part no NIBE Pool 20 Pool heating Makes pool heating possible with VVM 300. Part no DATASKYLT SERIENR VV KV NIBE RT 10 Room thermostat Part no F Part no NIBE Base extension Height: 125 mm Part no NIBE Lower cabinet Height: 375 mm Part no NIBE Over cabinet Height: 245 mm Part no Height: 345 mm Part no Height: mm Part no NIBE VVM
12 MILJÖMÄRKT NIBE is ISO-certified: SS-EN ISO 9001:2000 SS-EN ISO 14001:2004 This brochure is a publication from NIBE. All product illustrations, facts and specifications are based on current information at the time of the publication s approval. NIBE makes reservations for any factual or printing errors in this brochure. Printed by: AM-tryck & reklam. Photos: NIBE NIBE VVM 300 NIBE Energy Systems AB Box Markaryd SWEDEN Tel Technical PBD GB NIBE VVM
NIBE VVM 500 FLEXIBLE INDOOR MODULE INTELLIGENT HOT WATER NIBE VVM 500. Flexible all-in-one indoor module for heating and hot water.
NIBE VVM 500 FXIB INDOOR MODU INTELLIGENT HOT WATER Flexible all-in-one indoor module for heating and hot water. For upgrading existing heating systems or new buildings with requirements for high performance
More informationMOS GB NIBE VVM INSTALLATION AND MAINTENANCE INSTRUCTIONS NIBE VVM 300 VVM 300 LEK
A B I II III A B I II I II A B -2 0 +2 MOS GB 0821-4 NIBE VVM 300 511806 INSTALLATION AND MAINTENANCE INSTRUCTIONS NIBE VVM 300 VVM 300 LEK 2 1 LEK LEK 5 4 3 LEK LEK Contents User guide General Principle
More informationNIBE SPLIT ACVM 270 Air/water heat pump
NIBE SPLIT ACVM 270 Air/water heat pump NIBE SPLIT ACVM 270 system with complete indoor module NIBE SPLIT ACVM 270 is a complete modern heat pump system that offers effective technical energy saving and
More informationNIBE F2026 air/water heat pump. fresh air s free. NIBE F2026. Efficient scroll compressor that operates at temperatures down to -20 C.
NIBE F2026 air/water heat pump fresh air s free. Efficient scroll compressor that operates at temperatures down to -20 C. Automatic 2-step capacity regulator for the fan (not 6kW). Manufactured in three
More informationINSTALLATION AND MAINTENANCE INSTRUCTIONS MOS GB NIBE VVM 300 UK NIBE VVM 300 UK 230 V VVM 300 LEK
A B I II III A B I II I II A B -2 0 +2 MOS GB 1027-6 NIBE VVM 300 UK 031142 INSTALLATION AND MAINTENANCE INSTRUCTIONS NIBE VVM 300 UK 230 V VVM 300 2 1 5 4 3 Contents User guide General Principle of operation
More informationNIBE F1245 GROUND SOURCE HEAT PUMP. Heat pump with rock, ground or lake as heat source. NIBE F1245
NIBE F1245 GROUND SOURCE HEAT PUMP Heat pump with rock, ground or lake as heat source. New display unit with easy-to-read colour screen. Indoor sensor included See status and make settings via SMS with
More informationNIBE F470 A + Complete heat pump unit that provides heating, hot water, ventilation, heated supply air and heat recovery. Exhaust air heat pump
NIBE F470 Exhaust air heat pump Complete heat pump unit that provides heating, hot water, ventilation, heated supply air and heat recovery Display unit with easytoread colour screen. It also gives you
More informationInstaller manual ELK 213 Immersion heater
Installer manual ELK 213 LEK IHB GB 1535-3 031403 Table of Contents 1 English, IHB - ELK 213 General Component positions Pipe connections 2 2 3 5 Disturbances in comfort Accessories Technical data Electrical
More informationNIBE F750 A +++ Flexible, high-performance exhaust air heat pump. Exhaust air heat pump
NIBE F750 Exhaust air heat pump Flexible, highperformance exhaust air heat pump Energy and power efficient exhaust air heat pump with inverter controlled compressor. Display unit with easytoread colour
More informationOutline principle. Application Houses with water-borne heating systems. Maximal recommended heating output 13.5 kw. Alternative
Outline principle Application Houses with water-borne heating systems. Maximal recommended heating output 13.5 kw. Alternative NOTE! This is an outline diagram. Actual installation must be project planned
More informationMOS GB SMO INSTALLATION AND MAINTENANCE INSTRUCTIONS NIBE SMO 10
MOS GB 1236-6 SMO 10 511882 INSTALLATION AND MAINTENANCE INSTRUCTIONS NIBE SMO 10 Contents General System diagram 3 Principle of operation 3 Abbreviations 3 Front panel Display 4 Switch 5 Offset heating
More informationINSTALLATION AND MAINTENANCE INSTRUCTIONS FIGHTER FIGHTER 1127 LEK -2 +2
R 1-2 +2 MOS GB 737-2 INSTALLATION AND MAINTENANCE INSTRUCTIONS 31153 Table of Contents For Home Owners General System description Principle of operation 3 Front panel The front panel 4 Functions 4 Setting
More informationInstaller manual NIBE VVM 500
Installer manual Indoor module APH IHB EN 1751-9 031991 Quick guide Navigation Ok button (confirm/select) Back button (back/undo/exit) Control knob (move/increase/reduce) A detailed explanation of the
More informationGround source heat pump NIBE F1255
NIBE.EU Ground source heat pump NIBE F1255 NIBE F1255 is an intelligent, inverter-controlled ground source heat pump with integrated water heater. NIBE F1255 provides optimum savings since the heat pump
More informationMOS GB SMO INSTALLATION AND MAINTENANCE INSTRUCTIONS NIBE SMO 10
MOS GB 0707-3 SMO 10 511262 INSTALLATION AND MAINTENANCE INSTRUCTIONS NIBE SMO 10 Contents User guide System diagram 3 Principle of operation 3 Abbreviations 3 Front panel Display 4 Switch 5 Offset heating
More informationInstaller manual NIBE VVM 310
Installer manual EMK Indoor module APH IHB EN 1750-8 231175 Quick guide Navigation Ok button (confirm/select) Back button (back/undo/exit) Control knob (move/increase/reduce) A detailed explanation of
More informationair/water heat pump. NIBE F2040 provides
NIBE.EU Air/water heat pump NIBE F2040 NIBE F2040 is an intelligent and compact invertercontrolled air/water heat pump. NIBE F2040 provides optimum savings since the heat pump automatically adapts to your
More informationNIBE F1355. A +++ The system's efficiency class for heating. Speed-controlled ground source heat pump for large buildings. Ground source heat pump
NIBE F1355 Ground source heat pump Speed-controlled ground source heat pump for large buildings Optimal annual coefficient of performance and minimal operating costs thanks to the inverter controlled compressor.
More informationNIBE FIGHTER 1250 A B C D E F G
MOS GB 0844-5 031132 INSTALLATION AND MAINTENANCE INSTRUCTIONS User guide Transport / Installation Commissioning / Adjustment Accessories with quick guide Control / Alarm Technical data Item register A
More informationHeating when you need it Cooling when you don t
when you need it Cooling when you don t NIBE SPLIT air/water heat pump NIBE SPLIT is a system for heating, cooling and producing hot water for variety of house sizes It gives you an optimal annual heating
More informationNIBE F2120 Air/water heat pump
NIBE Air/water heat pump A breakthrough in efficiency NIBE is an air/water heat pump that has made a real breakthrough with a market leading SCOP. utilises the heat from the outdoor air which places big
More informationMOS GB SMO INSTALLATION AND MAINTENANCE INSTRUCTIONS NIBE SMO 10
MOS GB 0735-3 SMO 10 511882 INSTALLATION AND MAINTENANCE INSTRUCTIONS NIBE SMO 10 Contents General System diagram 3 Principle of operation 3 Abbreviations 3 Front panel Display 4 Switch 5 Offset heating
More informationInstaller manual NIBE F1145. Ground source heat pump. UK 1x230V IHB GB LEK
Installer manual UK 1x230V Ground source heat pump LEK IHB GB 1251-2 431074 A detailed explanation of the button functions can be found on page 28. How to scroll through menus and make different settings
More informationINSTALLATION AND MAINTENANCE INSTRUCTIONS FIGHTER 600P MOS GB FIGHTER 600P 1, 2,... LEK
,,... MOS GB 04-644 R INSTALLATION AND MAINTENANCE INSTRUCTIONS General Concise product description... Setting table... System description Principle of operation... System diagram... Front panel Front
More informationInstaller manual SMO 40
Installer manual UK Control module IHB GB 1546-3 231764 Quick guide Navigation Ok button (confirm/select) Back button (back/undo/exit) Control knob (move/increase/reduce) A detailed explanation of the
More informationInstaller manual NIBE VVM 320
Installer manual UK 1x230V Indoor module APH IHB GB 1613-6 231342 Quick guide Navigation Ok button (confirm/select) Back button (back/undo/exit) Control knob (move/increase/reduce) A detailed explanation
More informationInstaller manual AXC 30
LEK Installer manual AXC 0 Accessories IHB GB - Table of Contents General Contents Component positions Common electrical connection Connecting communication Connecting the supply Shunt controlled additional
More informationInstaller manual SMO 40
Installer manual Control module IHB EN 76-5 23760 Quick guide Navigation Ok button (confirm/select) Back button (back/undo/exit) Control knob (move/increase/reduce) A detailed explanation of the button
More informationINSTALLATION AND MAINTENANCE INSTRUCTIONS F F2025
MOS GB 0840-3 INSTALLATION AND MAINTENANCE INSTRUCTIONS 031185 LEK Table of Contents For Home Owners General System description Principle of operation 3 Maintenance routines General 4 For the Installer
More informationOutline principle. Application Buildings with water-borne heating systems. Alternative
Outline principle Application Buildings with water-borne heating systems. Alternative Additional heating before QN10 Accessories NOTE! This is an outline diagram. Actual installation must be engineered
More informationNIBE SPLIT HBS 05 Air/water heat pump
NIBE SPLIT HBS 05 Air/water heat pump NIBE SPLIT HBS 05 with several possibilities Can be docked with NIBE SMO and NIBE VVM. Customer adapted and cost effective split system. Possible to combine up to
More informationInstaller manual NIBE F1245. Ground source heat pump. UK 1x230V IHB GB
Installer manual UK 1x230V Ground source heat pump LEK IHB GB 1335-1 231613 A detailed explanation of the button functions can be found on page 29. How to scroll through menus and make different settings
More informationHeat pumps. for larger residential and commercial installations. Made in Sweden
Heat pumps for larger residential and commercial installations Made in Sweden Different energy sources Rock The heat pump collects stored solar energy from a collector in a hole drilled into the rock.
More informationINSTALLATION AND MAINTENANCE INSTRUCTIONS ELK ELK 15 LEK
MOS GB 1011-3 INSTALLATION AND MAINTENANCE INSTRUCTIONS 031179 LEK Table of Contents For Home Owners General System description Principle of operation 3 Abbreviations 3 System diagram 3 Operation and
More informationINSTALLATION AND MAINTENANCE INSTRUCTIONS AMB AMB 30 LEK
MOS GB 1044-1 INSTALLATION AND MAINTENANCE INSTRUCTIONS 031533 Table of Contents For the User General System description Principle of operation 3 Outdoor air operation 3 Hybrid operation 3 The control
More informationNIBE SPLIT ACVM 270, AMS 10
MOS GB 0923-1 INSTALLATION AND MAINTENANCE INSTRUCTIONS 031211 ACVM 270, AMS 10 LEK LEK LEK 2 1 LEK LEK LEK LEK 5 3 6 4 LEK LEK 7 LEK LEK LEK Table of Contents For Home Owners General 3 Installation data
More informationOutline principle. Application Buildings with water-borne heating systems. Alternative
Outline principle Application Buildings with water-borne heating systems. Alternative F1145/1245/1345 Master/Slave with additional heat, accessories and hot water heater (floating condensing). Heat pump
More informationInstaller manual NIBE F730
Installer manual Exhaust air heat pump IHB EN 1803-1 431700 Quick guide Navigation Ok button (confirm/select) Back button (back/undo/exit) Control knob (move/increase/reduce) A detailed explanation of
More informationInstaller manual SMO 20
Installer manual UK Control module IHB GB 546-5 23762 Quick guide Navigation Ok button (confirm/select) Back button (back/undo/exit) Control knob (move/increase/reduce) A detailed explanation of the button
More informationInstaller manual SMO 40
Installer manual Accessory Card Accessories IHB GB - 0 Table of Contents General Component positions Shunt controlled additional heat General Pipe connections Outline diagram Electrical connection Program
More informationUser manual NIBE F2026
User manual Air/water heat pump LEK UHB GB 1244-2 031864 Table of Contents 1 Important information 2 Installation data 2 Safety information 4 Serial number 5 Contact information 6 F2026 - An excellent
More informationOutline principle. Application Houses with water-borne heating systems. Alternative Select the desired configuration by highlighting the boxes below.
Outline principle Application Houses with water-borne heating systems. Alternative Select the desired configuration by highlighting the boxes below. NOTE! This is an outline diagram. Actual installation
More informationMOS GB INSTALLATION AND MAINTENANCE INSTRUCTIONS FIGHTER 1140 FIGHTER V, 3 X 230 V, 3 X 400 V LEK
MO GB 0903-6 031094 ITALLATIO AD MAITEACE ITRCTIO 230 V, 3 X 230 V, 3 X 400 V LEK LEK LEK LEK LEK LEK LEK LEK LEK General Concise product description... 2 etting table... 2 ystem description Principle
More informationAir/water - Heat pumps
Air/water - Heat pumps Installation of a NIBE air/water heat pump can lead to your energy consumption for heating being reduced by up to 50%, in comparison to conventional heating systems. Areas of Use
More informationTechnical description. Atec.
www.thermia.com Thermia Värmepumpar is not liable or bound by warranty if these instructions are not adhered to during installation or service. The English language is used for the original instructions.
More informationAir/water heat pump NIBE F2120
NIBE.EU Air/water heat pump NIBE F2120 NIBE F2120 is an inverter-controlled air/water heat pump which represent a real breakthrough when it comes to efficiency. With a seasonal performance factor in excess
More informationInstaller manual NIBE VVM 500. Indoor module APH
Installer manual Indoor module APH IHB GB 1428-5 031991 A detailed explanation of the button functions can be found on page 30. How to scroll through menus and make different settings is described on page
More informationInstaller manual NIBE VVM 310. Indoor module IHB GB
Installer manual Indoor module APH IHB GB 1338-3 231175 A detailed explanation of the button functions can be found on page 33. How to scroll through menus and make different settings is described on page
More informationInstaller manual NIBE F370. Exhaust air heat pump IHB GB LEK
Installer manual Exhaust air heat pump LEK IHB GB 1035-2 031546 A detailed explanation of the button functions can be found on page 33. How to scroll through menus and make different settings is described
More informationInstaller manual NIBE VVM 310. Indoor module IHB GB
Installer manual Indoor module APH IHB GB 1428-4 231175 A detailed explanation of the button functions can be found on page 33. How to scroll through menus and make different settings is described on page
More informationINSTALLATION AND MAINTENANCE INSTRUCTIONS EVP EVP 500 LEK
60 40 80 20 100 0 120 MOS GB 0923-2 INSTALLATION AND MAINTENANCE INSTRUCTIONS 031285 LEK LEK LEK LEK LEK LEK LEK 1 2 3 4 5 6 Table of Contents For Home Owners General System description Principle of operation
More informationNIBE SPLIT ACVM 270, AMS 10
MOS GB 1452-1 INSTALLATION AND MAINTENANCE INSTRUCTIONS 331183 ACVM 270, AMS 10 LEK LEK LEK 2 LEK LEK LEK LEK 1 7 5 3 6 LEK LEK LEK 4 AMS 10-8 K LE LE K LE K LEK LEK AMS 10-12 Table of Contents For Home
More informationInstaller manual NIBE F1245. Ground source heat pump. UK 1x230V
Installer manual UK 1x230V Ground source heat pump LEK IHB GB 1343-2 231995 A detailed explanation of the button functions can be found on page 32. How to scroll through menus and make different settings
More informationPlanning guide. Atec.
www.thermia.com Thermia Värmepumpar is not liable or bound by warranty if these instructions are not adhered to during installation or service. The English language is used for the original instructions.
More informationInstaller manual NIBE VVM 500. Indoor module APH
Installer manual Indoor module APH IHB GB 1216-2 031991 A detailed explanation of the button functions can be found on page 27. How to scroll through menus and make different settings is described on page
More informationInstaller manual NIBE F470
Installer manual Exhaust air heat pump LEK IHB EN 1751-1 431679 Quick guide Navigation Ok button (confirm/select) Back button (back/undo/exit) Control knob (move/increase/reduce) A detailed explanation
More informationELK 26 INSTALLATION AND MAINTENANCE INSTRUCTIONS ELK 26
MOS GB 38-2 INSTALLATION AND MAINTENANCE INSTRUCTIONS 2352 LEK Table of Contents For Home Owners General System description Principle of operation 3 Components 3 System diagram 3 Operation and maintenance
More informationInstaller manual NIBE VVM 320. Indoor module IHB GB
Installer manual Indoor module APH IHB GB 1452-3 231357 A detailed explanation of the button functions can be found on page 33. How to scroll through menus and make different settings is described on page
More informationInstaller manual NIBE VVM 320. Indoor module IHB GB
Installer manual Indoor module APH IHB GB 1336-1 231357 A detailed explanation of the button functions can be found on page 32. How to scroll through menus and make different settings is described on page
More informationHT V2 HT Split
Scroll compressor Refrigerant R07C Aqu@Scop HT V Aqu@Scop HT Split High Temperature Air-to-Water Heat Pumps Models -, -7 and 8-9.0 to 7.9kW Aqu@Scop HT V / Aqu@Scop HT Split Installation examples - Single
More informationAccumulator tank. 1000, 750 and 500 litres Aqualux Teknik Aqualux UB Aqualux 750 CU
Installation, operation and maintenance Accumulator tank 1000, 750 and 500 litres Aqualux Teknik Aqualux B Aqualux 750 C Aqualux 750 Teknik with bivalent shunt, optional extra 2012-02-08 ver.: Supersedes:
More informationInstaller manual AHP/AHPS
Installer manual Accumulator tank IHB GB 1415-2 231351 Table of Contents 1 Important information Safety information 2 2 AHP and AHPS Installation alternative 10 11 2 Delivery and handling Transport 5
More informationFIL-SPL Flow-through heater for central heating USER MANUAL
FIL-SPL Flow-through heater for central heating with 0-10 V EP 15-30 control unit USER MANUAL Kaukora LTD. D106159 r3.0 Contents 1. Important information... 5 Safety information... 5 General... 5 Marking...
More informationInstallation, operation and care Wall-mounted electric boiler MP THL nr. - rev 02
Installation, operation and care Wall-mounted electric boiler MP 4 150206 THL nr. - rev 02 Contents Notes... 3 Safety and handling... 4 Operation... 5 Technical data... 6 Pipe installation... 8 System
More informationMOS GB INSTALLATION AND MAINTENANCE INSTRUCTIONS VEDEX 1000 VEDEX 1000 M10527 LEK
LEK MOS GB 0733-1 VEDEX 1000 M10527 INSTALLATION AND MAINTENANCE INSTRUCTIONS VEDEX 1000 Contents For Home Owners Installation data 2 System diagram 3 Product description 3 Area of use 3 Heating 3 Component
More informationInstallation instructions Danfoss heat pump DHP-R
Installation instructions Danfoss heat pump DHP-R Table of contents DHP-R 1 Important information........................................................... 5 1.1 Refrigerant...5 1.2 Noise and vibrations...5
More informationINSTALLATION AND MAINTENANCE INSTRUCTIONS FIGHTER 1220 MOS GB FIGHTER Fighter 1220
MO GB 0429-1 011676 R INTALLATION AND MAINTENANCE INTRCTION Fighter 1220 LEK General Concise product description... 2 etting table... 2 ystem description Principle of operation... 3 Front panel Layout...
More informationInstaller manual NIBE VVM 310
Installer manual EMK Indoor module APH IHB GB 1524-5 231175 Quick guide Navigation Ok button (confirm/select) Back button (back/undo/exit) Control knob (move/increase/reduce) A detailed explanation of
More informationInstallation, operation and maintenance. Accumulator tank. Acc-tank 500 CU. Acc-tank 500 UB ver: Supersedes:
Installation, operation and maintenance Accumulator tank Acc-tank 500 CU 2010-11-2 ver: Supersedes: Acc-tank General information 1011 Read through these instructions carefully before carrying out installation,
More informationUser and Installer manual NIBE UKV 20
User and Installer manual 20-500, 20-750, 20-1000 Accumulator tank CHB EN 1743-1 431416 Table of Contents 1 Important information 2 For the User 3 For the Installer 4 Technical data Contact information
More informationInstaller manual NIBE VVM 500
Installer manual Indoor module APH IHB GB 1705-8 031991 Quick guide Navigation Ok button (confirm/select) Back button (back/undo/exit) Control knob (move/increase/reduce) A detailed explanation of the
More informationInstaller manual AXC 40. Accessories IHB GB LEK
EK Installer manual AXC 0 Accessories IHB GB 0-0 Table of Contents General Contents Component positions Common electrical connection Connecting the supply Connecting communication Shunt controlled additional
More informationInstaller manual NIBE F1145
Installer manual UK 1x230V Ground source heat pump LEK IHB GB 1643-2 331510 Quick guide Navigation Ok button (confirm/select) Back button (back/undo/exit) Control knob (move/increase/reduce) A detailed
More informationECL Comfort V a.c. and 24 V a.c.
230 V a.c. and 24 V a.c. Description and application In heating applications the can be integrated with the Danfoss Link solution via the DLG interface for use in single-family applications. The controller
More informationNIBE SPLIT ACVM , AMS 10
MOS GB 1252-4 INSTALLATION AND MAINTENANCE INSTRUCTIONS 431156 ACVM 10-270, AMS 10 LEK LEK LEK 2 LEK LEK LEK LEK 1 7 5 3 6 LEK LEK LEK 4 $06 K LE LE K LE K LEK LEK $06 Table of Contents For Home Owners
More informationTechnical Guide. Installation, Operation and Care. EP E series 7 step electric boilers 26 and 42 kw
Technical Guide Installation, Operation and Care EP E series 7 step electric boilers 26 and 42 kw Arkelstorpsvägen 88, 291 94 KRISTIANSTAD Tel +46 44-22 63 20, Telefax +46 44-22 63 58 e-mail: info@varmebaronen.se
More informationPELLUX INSTALLATION AND MAINTENANCE INSTRUCTIONS PELLUX 100 H AP
MOS GB 1411-1 331139 INSTALLATION AND MAINTENANCE INSTRUCTIONS H AP Table of Contents For Home Owners General System description Area of use 3 Product description 3 Heating 3 Hot water heating 3 System
More informationInstaller manual AHP/AHPS
Installer manual Accumulator tank IHB GB 1544-4 231351 Table of Contents 1 Important information 3 Installation alternative 13 Safety information 3 5 Electrical installation 15 2 Delivery and handling
More informationLEK MOS UK VPA 300/200, 450/ INSTALLATION AND MAINTENANCE INSTRUCTIONS VPA 300/200, 450/300
MOS UK 1240-7 VPA 300/200, 450/300 031049 INSTALLATION AND MAINTENANCE INSTRUCTIONS VPA 300/200, 450/300 For Home Owners System description System description Unvented water heater for use with ground
More informationAGEO CALEO. Water-to-water high temperature heat pumps USE RANGE DESCRIPTION. Designed to replace a conventional boiler and produce domestic hot water
Designed to replace a conventional boiler and produce domestic hot water Heating capacity : 16 to 25 Heating Hydraulic module ENVIRONMENTALLY HFC R4A PROTECTION DE FRIENDLY L'ENVIRONNEMENT USE CIAT is
More informationNIBE IT S IN OUR NATURE
IT S IN OUR NATURE WWW.NIBE.EU NIBE product range Ground source heat pumps Air/water heat pumps Exhaust air heat pumps Air/air heat pumps Hot water supply Ventilation Solar energy production Domestic boilers
More informationCombine. accumulators AQUALUX ACKTANK. Combine heat sources for cheap heating
Combine accumulators AQALX ACKTANK Combine heat sources for cheap heating Shunt package not included. Store heat in water FTRE-PROOF YOR HEATING SYSTEM! An accumulator tank contains water and its main
More informationUser manual. JASPI COMFORT MONO 8 & 12Kw UK 1x230V. Air/water heat pump LEK
LEK LEK User manual LEK JASPI COMFORT MONO 8 & 12Kw UK 1x230V Air/water heat pump UN Table of Contents 1 Important information 3 Installation data 3 Safety information 4 Serial number 6 Country specific
More informationECL Comfort 210 controller, Remote Control Units ECA 30 / 31 and Application keys
ECL Comfort 210 controller, Remote Control Units ECA 30 / 31 and Application keys Designed in Denmark Description ECL Comfort 210 controller series ECL 210 The ECL Comfort 210 is an electronic weather
More informationInstaller manual NIBE FLM. Exhaust air module IHB GB LEK
Installer manual Exhaust air module IHB GB 1414-4 031375 Table of Contents 1 Important information 2 Connections 14 Safety information 2 6 Commissioning and adjusting 19 2 Delivery and handling Transport
More informationInstallation and Commissioning Instructions FMU3 Floor Mixing Unit with Grundfos UPM3 Pump
Installation and Commissioning Instructions FMU3 Floor Mixing Unit with Grundfos UPM3 Pump Reduced Installation time Precision regulation Minimal tooling required 100% tested prior to packaging High quality
More informationINSTALLATION AND MAINTENANCE INSTRUCTIONS PELLUX PELLUX 100 H AP
MOS GB 1248-1 231259 INSTALLATION AND MAINTENANCE INSTRUCTIONS H AP Table of Contents For Home Owners General System description Area of use 3 Product description 3 Heating 3 Hot water heating 3 System
More informationInstaller manual NIBE F750. Exhaust air heat pump IHB GB LEK
Installer manual Exhaust air heat pump IHB GB 1437-1 231917 A detailed explanation of the button functions can be found on page 30. How to scroll through menus and make different settings is described
More informationCTC EcoComfort. Installation and Maintenance Manual. for the property owner. Providing sustainable energy solutions worldwide
162 105 25-2 2015-11-16 Providing sustainable energy solutions worldwide Installation and Maintenance Manual CTC EcoComfort for the property owner IMPORTANT READ CAREFULLY BEFORE USE KEEP FOR FUTURE REFERENCE
More informationLK Electric Boiler - 4,5
LK Electric Boiler -, Design LK Electric Boiler, kw is a wall-mounted electric boiler, intended primarily for low-temperature heating systems, e.g. under floor heating. LK Electric Boiler, kw is delivered
More informationECL Comfort 210 controller, Remote Control Units ECA 30 / 31 and Application keys Designed in Denmark
ECL Comfort 210 controller, Remote Control Units ECA 30 / 31 and Application keys Designed in Denmark Description ECL Comfort 210 controller series The ECL Comfort 210 is an electronic weather compensated
More informationA Evaporator B Fan C Terminal box D Hermetically sealed, output regulated digital scroll compressor E Condenser
Vitocal 300-A, type AWC-I and AW-O.1 Product description A Evaporator B Fan C Terminal box D Hermetically sealed, output regulated digital scroll compressor E Condenser & High operational reliability,
More informationInstaller manual AG-AA10. Air/air heat pump IHB GB AG-AA10-30 AG-AA10-40/50
-30 Installer manual Air/air heat pump -40/50 IHB GB 1516-1 331554 Table of Contents 1 Important information 2 5 Installation 7 Safety information 2 Model combinations 7 Read before starting the installation
More informationThe ECL Comfort 110 is a universal 1-circuit controller for use in district heating substations and district heating systems as well as boilerbased
Data sheet ECL Comfort 110 230 V a.c. and 24 V a.c. Description and application ECL Comfort 110 The ECL Comfort 110 is a universal 1-circuit controller for use in district heating substations and district
More informationInstaller manual NIBE F1245PC. Ground source heat pump IHB GB
Installer manual Ground source heat pump LEK IHB GB 1506-3 231810 A detailed explanation of the button functions can be found on page 34. How to scroll through menus and make different settings is described
More informationHome owner user pack for the Nibe 200P
Home owner user pack for the Nibe 200P How to use this pack: Section 1 Please print these pages and laminate back to back to create a single document. This laminated document should be left with the Unit
More informationPlanning guide. (2010/09) en
Planning guide (2010/09) en 1 Planning guide for Greenline HE E 21, 28 and HE D 36, 43 Page Contents 3 Documentation and VPW2100 4 Technical data of heatpump 5 Dimensioning of DHW systems 6 Symbol explanations
More informationInstallation & Operating Instructions IMage Pool Control Type
Installation & Operating Instructions IMage Pool Control Type 34-015040 International Marketing A/S reserves the right to make product changes without notice. Copyright: International Marketing A/S Edition
More informationTank systems. Layered tank Solar layered tank Hygienic layered tank Modular layered tank Hot water tank NEW:
Tank systems Layered tank Solar layered tank Hygienic layered tank Modular layered tank Hot water tank NEW: NEOPOR AND FLEECE INSULATION SENSOR TERMINAL STRIP ADJUSTABLE FEET www.froeling.com Energy management
More informationUser manual JÄSPI Inverter Nordic 8, 12, 16, 20
User manual 8, 12, 16, 20 Air/water heat pump LEK UHB GB 1648-1 331844 Table of Contents 1 Important information Installation data Safety information JÄSPI Inverter Nordic An excellent choice 2 The heat
More information