Viking Installation Guide

Transcription

1 Viking Installation Guide Built-In Electric Induction Cooktop Viking Range Corporation 111 Front Street Greenwood, Mississippi USA

2 IMPORTANT: PLEASE READ AND FOLLOW Before beginning, please read these instructions completely and carefully. Do not remove permanently affixed labels, warnings, or plates from the product. This may void the warranty. Please observe all local and national codes and ordinances. Please ensure that this product is properly grounded. The installer should leave these instructions with the consumer who should retain for local inspector s use and for future reference. Installation must conform with local codes or, in the absence of codes, the National Electrical Code, ANSI/NFPA 70-latest edition. IN CANADA: Electrical installation must be in accordance with the current CSA C22.1 Canadian Electrical Codes Part 1 and/or local codes. GENERAL INFORMATION 1. WARNING: The use of cabinets for storage above the appliance may result in potential burn hazard. Combustible items may ignite, metallic items may become hot and cause burns. If a cabinet storage is to provided the risk can be reduced by installing a range hood that projects horizontally a minimum of 5 in. beyond the bottom of the cabinets. 2. WARNING: This appliance shall not be used for space heating. This information is based on safety considerations. 3. All openings in the wall behind the appliance in the floor under the appliance shall be sealed. 4. Keep appliance area clear and free from combustible materials, gasoline, and other flammable vapors. 5. Disconnect the electric supply to the appliance before cleaning or servicing. 6. When removing the cooktop for service and/or cleaning, disconnect AC power supply. 7. Electrical Requirement: Listed on Specifications/Wiring Diagram Sheet - Minimum Recommended Electric Circuit. WARNING ELECTRICAL GROUNDING INSTRUCTIONS This cooktop must be electrically grounded in accordance with local codes or, in the absence of codes, with the National Electrical Code, ANSI/NFPA 70-latest edition.. FOR PERSONAL SAFETY, THIS APPLIANCE MUST BE PROPERLY GROUNDED. ELECTRICAL REQUIREMENTS Check your local codes regarding this unit. This cooktop is supplied with a 3-wire, A.C. 208Y/120 volt or 120/240 volt, 60 HZ electrical system. A white (neutral) is not needed for this unit. See next section for grounding instructions. It should be fused separately. CAUTION: Be sure the electric power is off from the breaker box to the junction box until the cooktop is installed and ready to operate. The junction box should be connected to a suitable ground. Refer to the specifications chart for kilowatt rating and recommended amperage. House wiring and fusing must comply with local codes. If no local codes are applicable, wire in accordance with the National Electrical Code, ANSI/NFPA 70-latest edition. ELECTRICAL CONNECTION WARNING: The electrical power to the unit must be shut off while line connections are being made. Failure to do so could result in serious injury or death. When making the wire connections, use the entire length of the conduit provided (3 feet). The conduit must not be cut. Connect the red and black leads from the unit conduit to the corresponding leads in the junction box. The bare ground wire in the conduit is connected to the unit frame. When connecting to a 3- conductor branch circuit, if local codes permit, connect the bare ground connector lead of the unit to the branch circuit neutral (gray or white in color). DO NOT USE AN EXTENSION CORD WITH THIS APPLIANCE. SUCH USE MAY RESULT IN A FIRE, ELECTRICAL SHOCK OR OTHER PERSONAL INJURY. 2

3 SPECIFICATIONS - INDUCTION/RADIANT COOKTOP Description 30 W. VCCU 36 W. VCCU Cutout Width Minimum 28 9/16 (72.6 cm) 34 9/16 (87.8 cm) Maximum 29 5/8 (75.2 cm) 35 1/2 (90.2 cm) Cutout Depth Minimum /8 (48.6 cm) Maximum /8 (50.5 cm) Overall Width 30 3/4 (78.1 cm) 36 3/4 (93.3 cm) Overall Height from Bottom 6 3/4 (17.2 cm) Overall Depth from Rear 21 (53.3 cm) Electrical Requirements /120 VAC/60 Hz - 3-wire conduit with a No. 10 ground wire. Maximum Amp Usage 240V 9.1 kw; 37.9 amps 13.2 kw 55.0 amps 208V 7.4 kw; 35.4 amps 10.4 kw 50.2 amps Surface Element Rating 240V 208V 240V 208V Right Front watts watts Right Rear watts watts Center Front N/A N/A Bridge N/A N/A watts Center Rear N/A N/A Left Front watts watts Left Rear watts watts Approximate Shipping Weight 52 lb. (23.4 kg) 63 lb. (28.4 kg) SPECIFICATIONS - ALL INDUCTION COOKTOP Description 30 W. VICU 36 W. VICU Cutout Width Minimum 28 9/16 (72.6 cm) 34 9/16 (87.8 cm) Maximum 29 5/8 (75.2 cm) 35 1/2 (90.2 cm) Cutout Depth Minimum /8 (48.6 cm) Maximum /8 (50.5 cm) Overall Width 30 3/4 (78.1 cm) 36 3/4 (93.3 cm) Overall Height from Bottom 6 11/16 (17.0 cm) Overall Depth from Rear 21 (53.3 cm) Electrical Requirements /120 VAC/60 Hz - 3-wire conduit with a No. 10 ground wire. Maximum Amp Usage 240V 9.0 kw; 37.5 amps 13.5 kw 56.3 amps 208V 7.8 kw; 37.5 amps 11.6 kw 56.3 amps Surface Element Rating 240V 208V 240V 208V Right Front watts watts Right Rear watts watts Center Front N/A N/A watts Center Rear N/A N/A watts Left Front watts watts Left Rear watts watts Approximate Shipping Weight 52 lb. (23.4 kg) 63 lb. (28.4 kg) 3

4 PROXIMITY TO SIDE CABINET INSTALLATION 1. The cooktop may be installed directly to existing base cabinets. 2. The cooktop CANNOT be installed directly adjacent to sidewalls, tall cabinets, tall appliances, or other side vertical surfaces above 36 (91.4 cm) high. There must be a minimum of 6 (15.2 cm) side clearance from the cooktop to such combustible surfaces above the 36 (91.4 cm). 3. Within the 6 (15.2 cm) side clearance to combustible vertical surfaces above 36 (91.4 cm), the maximum wall cabinet depth must be 13 (33.0 cm) and wall cabinets within this 6 (15.2 cm) side clearance must be 18 (45.7 cm) above the 36 (91.4 cm) high countertop. 4. Wall cabinet above the cooktop must be a minimum of 36 (91.4 cm) above the countertop for a full width of the cooktop. 13 Max (33.0 cm) 36 Min. (91.4 cm) 6 Min.(15.2 cm) 18 Min. (45.7 cm) 0 Min.* (0 cm) 36 Min. (91.4 cm) 3 1/8 (7.9 cm) MINIMUM CLEARANCES FROM ADJACENT COMBUSTIBLE CONSTRUCTION Above countertop (above 36 [91.4 cm]) Side 6 (15.2 cm) Rear* 0 (0 cm) Within 6 side clearance. Wall cabinets no deeper than 13 (33.0 cm) Must be minimum 18 (45.7 cm) above countertop Wall cabinets directly above the product must be minimum 36 (91.4 cm) above the countertop. *NOTE: Before cutting countertop cutout, check the inside clearance available from the inside back wall to the proposed placement of the cooktop. A minimum of 2 (5.1 cm) is required from the back wall of the cooktop to the inside wall of the back cabinet. (See page 4) This may require a distance greater than the 0 minimum approved distance. 4

5 INTERIOR CABINET CLEARANCES IMPORTANT: The electronic components for the induction elements in the cooktop need some air circulation. To ensure long life of electronic components, it is required that a minimum of 8 (20.3 cm) open space remain between the bottom of the cooktop and any shelf underneath. The maximum length of the shelf underneath is 18 (45.7cm). There should be no partition or shelf directly underneath the unit. It is also required that the exit air ports at the rear are not blocked. There should be a minimum of 2 (5.1 cm) space between the exit air ports at the rear of the unit and any nearby obstruction. 8 (20.3 cm) min. 18 (45.7 cm) max. 2 (5.1 cm) min. 5

6 DIMENSIONS INDUCTION/RADIANT COOKTOP 30 W. TOP 21 (53.3 cm) 30 3/4 (78.1 cm) 30 W. BURNER BOX 18 3/8 (46.7 cm) 30 W. HEIGHT 6 7/16 (16.4 cm) 5 1/4 (13.3 cm) 4 1/2 (11.4 cm) 6 11/16 (17.0 cm) After installation of cooktop, locate the four hold down brackets on each side of the burner box. Screw the sheet metal screw into bracket and tighten firmly against bottom of countertop. 6

7 36 W. TOP 21 (53.3 cm) 36 3/4 (93.3 cm) 36 W. BURNER BOX #1 # /32 (48.2 cm) #1 #2 #1 #2 34 1/2 (87.6 cm) There are two types of hold down brackets on the 36 w. cooktop. After installing cooktop, locate the hold down brackets around the burner box. Brackets #1 are located on the left side of the burner box and brackets #2 are located on the right side of the burner box. Screw the sheet metal screw into the brackets and tighten firmly against bottom of countertop. #1 #2 36 W. HEIGHT 3 1/16 (7.8 cm) 4 15/32 (11.4 cm) 5 7/32 (13.3 cm) 6 11/16 (17.0 cm) 2 5/16 (5.9 cm) 7

8 DIMENSIONS ALL INDUCTION COOKTOP 30 W. TOP 30 3/4 (78.1 cm) 21 (53.3 cm) 30 W. BURNER BOX 18 3/4 (47.6 cm) 30 W. HEIGHT 4 1/16 (10.3 cm) 5 1/8 (13.0 cm) 7 1/2 (19.1 cm) 28 1/2 (72.4 cm) After installation of cooktop, locate the four hold down brackets on each side of the burner box. Screw the sheet metal screw into bracket and tighten firmly against bottom of countertop. 8

9 36 W. TOP 36 3/4 (93.3 cm) 21 (53.3 cm) 36 W. BURNER BOX 18 3/4 (47.6 cm) 36 W. HEIGHT 4 1/32 (10.2 cm) 5 3/16 (13.2 cm) 7 1/2 (19.1 cm) After installation of cooktop, locate the four hold down brackets on each side of the burner box. Screw the sheet metal screw into bracket and tighten firmly against bottom of countertop. 9

10 30 W. CUTOUT Min. 19 1/8 (48.6 cm) Max. 19 7/8 (50.5 cm) Min. 28 9/16 (72.6 cm) Max. 29 5/8 (75.2 cm) 30 W. CUTOUT w/ DOWNDRAFT 7/8 (2.2 cm) 27 (68.6 cm) 7/8 (2.2 cm) 2 1/4 (5.7 cm) 20 1/4 (51.4 cm) 28 3/4 (73.0 cm) 10

11 36 W. CUTOUT Min. 19 1/8 (48.6 cm) Max. 19 7/8 (50.5 cm) Min. 34 9/16 (87.8 cm) Max. 35 1/2 (90.2 cm) 36 W. CUTOUT w/ DOWNDRAFT 7/8 (2.2 cm) 33 (83.8 cm) 7/8 (2.2 cm) 2 1/4 (5.7 cm) 20 1/4 (51.4 cm) 34 3/4 (88.3 cm) FINAL PREPARATION 1. Some stainless steel parts may have a plastic protective wrap which must be peeled off. 2. All stainless steel body parts should be wiped with hot, soapy water and with a liquid cleaner designed for this material. If buildup occurs, do not use steel wool, abrasive cloths, cleaners, or powders! If it is necessary to scrape stainless steel to remove encrusted materials, soak with hot, wet cloths to loosen the material, then use a wood or nylon scraper. Do not use a metal knife, spatula, or any other metal tool to scrape stainless steel! Scratches are almost impossible to remove. REPLACEMENT PARTS Only authorized replacement parts may be used in performing service on the cooktop. Do not repair or replace any part of the appliance unless specifically recommended in the manual. All other servicing should be referred to a qualified technician. 11

12 WIRING DIAGRAM 30 W. INDUCTION/RADIANT COOKTOP L2 /BLK /BLK YEL/ YEL/ WH/ 1500 WATT L.R. ELEM. /BLK P L L WARNING- THIS UNIT MUST BE GROUNDED. SEE INSTALLATION INSTRUCTIONS FOR PROPER GROUNDING PROCEDURES BLK WH/ /YEL /BLK AC1 AC2 JR L2 EMI BOARD JF AC1 AC WATT R. R. COIL LOW JOUT1 AC1 AC2 J3 VOLTAGE J3 AC2 AC1 JOUT1 POWER POWER JOUT2 BOARD BOARD JOUT2 PURPLE PURPLE H1 H2 (H2) (H1)a (H1)b P L2 /BLK 10K POT NOTE: TRAILERS OR STRIPES WILL BE THE SECOND COLOR IN A COLOR COMBINATION 2500/1000 WATT L. F. ELEM. BLK BLK/WH /BLK 1800 WATT R.F. COIL MOTOR WH/BLK 10K POT SURF. ELEM. POWER ON LIGHT /BLK /BLK WH/BLK YEL/BLK YEL/BLK WH/BLK WIRING DIAGRAM 36 W. INDUCTION/RADIANT COOKTOP /BLK /BLK L2 WH/BLK WH/BLK YEL/BLK 10K POT YEL/BRN YEL/BRN WH/ 1500 WATT L.R. ELEM. /BLK WH/ (H2) (H1)a BLK YEL/BLK WH/ 3300 WATT R. R. COIL (H1)b P L2 /BLK BLK/WH 1800 WATT BRIDGE ELEM /BLK AC1 AC2 JR L2 EMI BOARD JOUT1 JOUT2 AC1 POWER BOARD AC2 J1 LOW VOLTAGE PURPLE /BLK P L H1 L H2 800 WATT /YEL JF AC1 AC2 J WATT AC2 POWER BOARD (H2) (H1)a AC1 JOUT1 JOUT2 (H1)b P 2200/750 WATT L. F. ELEM. /BLK /BLK L2 /BLK BLK /BLK YEL/ GRAY WH/GRN 1800 WATT R.F. COIL PURPLE P L H1 L H2 PURPLE MOTOR YEL/ /YEL 10K POT /BLK /BLK YEL/ YEL/ /YEL WH/GRN WH/GRN YEL/GRN YEL/GRN PURPLE WARNING- THIS UNIT MUST BE GROUNDED. SEE INSTALLATION INSTRUCTIONS FOR PROPER GROUNDING PROCEDURES NOTE: TRAILERS OR STRIPES WILL BE THE SECOND COLOR IN A COLOR COMBINATION SURF. ELEM. POWER ON LIGHT 12

13 WIRING DIAGRAM 30 W. ALL INDUCTION COOKTOP CHASSIS GROUND GREEN L2 POWER BOARD L2C C L2R R POWER LINE CONDITIONER J3 J2 J1 POWER BOARD J16 J17 JOUT1 JOUT2 J16 J17 JOUT1 JOUT2 J3 J3 JE3 JE4 AC J6 J7 J14 J15 JE3 JE4 AC J6 J7 J14 J15 JE1 EMI BOARD JE5 JE6 JE2 J5 J11 J10 J9 J8 FRONT LED BOARD REAR JE1 EMI BOARD JE5 JE6 JE2 J5 J11 J10 J9 J8 REAR LED BOARD FRONT JE7 JE8 J12 J13 JE7 JE8 J12 J13 J2 J3 J2 J3 J18 J19 JOUT3 JOUT4 J18 J19 JOUT3 JOUT4 LEFT SECTION FOR CONNECTION TO FACTORY INSTALLED TERMINAL BLOCK - USE COPPER OR ALUMINUM CONDUCTORS WARNING- THIS UNIT MUST BE GROUNDED. SEE INSTALLATION INSTRUCTIONS FOR PROPER GROUNDING PROCEDURES NOTE: TRAILERS OR STRIPES WILL BE THE SECOND COLOR IN A COLOR COMBINATION RIGHT WIRING DIAGRAM 36 W. ALL INDUCTION COOKTOP CHASSIS GROUND GREEN L2 POWER BOARD L2L L J6 J5 L2C C L2R R POWER LINE CONDITIONER J3 J2 J1 POWER BOARD J16 J17 JOUT1 JOUT2 J16 J17 JOUT1 JOUT2 J3 J3 JE3 JE4 AC J6 J7 J14 J15 JE3 JE4 AC J6 J7 J14 J15 JE1 EMI BOARD JE5 JE6 JE2 J5 J11 J10 J9 J8 REAR LED BOARD FRONT JE1 EMI BOARD JE5 JE6 JE2 J5 J11 J10 J9 J8 REAR LED BOARD FRONT JE7 JE8 J12 J13 JE7 JE8 J12 J13 J3 J2 J2 J3 J18 J19 JOUT3 JOUT4 POWER BOARD J18 J19 JOUT3 JOUT4 LEFT SECTION FOR CONNECTION TO FACTORY INSTALLED TERMINAL BLOCK - USE COPPER OR ALUMINUM CONDUCTORS JE3 JE4 JE1 EMI BOARD JE5 AC J16 J17 J6 J7 JOUT1 JOUT2 J3 J14 J15 J11 J10 FRONT LED BOARD RIGHT JE6 J5 J9 WARNING- THIS UNIT MUST BE GROUNDED. SEE INSTALLATION INSTRUCTIONS FOR PROPER GROUNDING PROCEDURES NOTE: TRAILERS OR STRIPES WILL BE THE SECOND COLOR IN A COLOR COMBINATION JE2 JE7 JE8 J18 J19 J8 J12 J13 J2 J3 JOUT3 JOUT4 CENTER REAR

14 14

15 15

16 Viking Range Corporation 111 Front Street Greenwood, Mississippi USA (662) For more product information call VIKING1 ( ) or visit the Viking Web site at vikingrange.com F20112D (PS0306VR)