IA Inlet Actuator. Instruction Manual. IA Inlet Actuator Models: IA0090 IA0090P. Munters Corporation, March 2017 QM1235r1

Transcription

1 Instruction Manual IA Inlet Actuator IA Inlet Actuator Models: IA0090 IA0090P Munters Corporation, March 2017 QM1235r1 1

2 IA Inlet Actuator Manual for use and Maintenance Thank You: Thank you for purchasing a Munters IA Inlet Actuator. Munters equipment is designed to be the highest performing, highest quality equipment you can buy. With the proper installation and maintenance it will provide many years of service. Description: The IA0090 motor gearbox is a maintenance-free, compact drive unit for accurately opening and closing air inlet flaps, air valves and ventilation curtains in livestock houses and crop storage buildings. The IA0090 motor gearbox features a self-braking worm gear transmission. This transmission ensures that the drive shaft is not rotatable when the drive unit is stopped. The combination of carefully matched pinion and worm reductions results in a quiet mechanical transmission. The IA0090 motor gearboxes feature a power switching integrated linear limit switch system with duty and safety switches with an excellent switching precision of the end positions. The maximum switching range of the limit switch system equates to 55 revolutions of the drive shaft. With use of an optional potentiometer built-in set, it is possible to precisely feedback intermediate and end positions to a (climate) computer. The IA0090 motor gearboxes are finished with a blue powder coating and are supplied including mounting bolts and spring washers. IA0090 motor gearboxes: Drive torques of 1000 lb. in.j 1.2 at 60 Hz mains frequency; Suitable for intermittent use, duty class s3-30%, duty cycle maximum 25 minutes; Provided with a two-sided output drive shaft for mounting one winch or belt drum or two16-tooth 1/2 x5/16 zinc-plated sprockets for chain couplings; Manual drive enabled by means of a hexagon socket in electric motor shaft; Electric motors are standard tropic-proof and conform to protection class IP55; Available as 1-phase 115 V (60 Hz) electric motor with UL and CSA approval. Please Note: To achieve maximum performance and insure long life from your Munters product it is essential that it be installed and maintained properly. Please read all instructions carefully before beginning installation. Warranty: For Warranty claims information see the Warranty Claims and Return Policy form QM1021 available from the Munters Corporation office at or by at aghort.info@munters.com. Conditions and Limitations: Products and Systems involved in a warranty claim under the Warranty Claims and Return Policy shall have been properly installed, maintained and operated under competent supervision, according to the instructions provided by Munters Corporation. Malfunction or failure resulting from misuse, abuse, negligence, alteration, accident or lack of proper installation or maintenance shall not be considered a defect under the Warranty. 2 QM1235r1 Munters Corporation, March 2017

3 Index Chapters Page 1. Unpacking the Equipment 1.1 Technical specifications IA0090 motor gearbox Configurations IA0090 motor gearbox Options for IA0090 motor gearbox Dimensions IA0090 motor gearbox 5 2. Installation Instructions 2.1 Mounting the IA0090 motor gearbox Mounting the drum, winch belt and couplings (configuration 1) Pre-winding the winch belt onto the belt drum (configuration 1) 8 3. Connection and Operations 3.1 Connection and operation - abbreviations Connecting the control components: switch materials and cable lenghts Overview: connections and elements for Operating & Setting Rotational directions and end positions IA0090 motor gearbox Wiring diagrams IA0090 motor gearbox Setting the limit switch system Potentiometer installation set: installation Potentiometer table IA0090 motor gearbox (i=1,0) Maintenance 4.1 Maintenance IA0090 motor gearbox 19 Munters Corporation, March 2017 QM1235r1 3

4 About the Equipment Technical Specifications IA0090 Motor Gearbox Mechanical Torque Speed Winch belt speed Winch belt length Drive unit Weight 1000 lb. in. 1.2 rpm inch/min 39.4 inch Self-locking 34.2 lb Electrical Supply voltage (A ) Maximum current (A ) Power 115 V 2.5 A 90 W Environment Protection class Operating temperature IP55 0 tot 40 C (32 tot 104 F) 1.2 Configurations IA0090 Motor Gearbox The IA0090 ships in 2 boxes, Box 1 of 2 is the Gear Motor and Box 2 of 2 is the installation kit. The IA0090 is standard delivered with a 1-phase motor: A - 115V The IA0090 is standard delivered with limit switch system and mounting kit. Configurations include double belt drum, Belt Drum w/option to use cables. Options: Potentiometer Options and accessories are ordered separately. CONFIGURATIONS : Belt drum Ceiling Mount Wall Mounts 4 QM1235r1 Munters Corporation, March 2017

5 Chapter 1 About the Equipment Items to Order Seperately: IA0090, IA0090P Drum Kit with Mounting Bracket AC Options for IA0090 Motor Gearbox Potentiometer: Position feedback IA0090P An optional potentiometer built-in set (AC1429) for the IA0090 motor gearbox. Position feedback which works in combination with the limit switch system. The built-in set with potentiometer makes it possible to signal with precision to a (climate) computer, not just the start and end positions of the limit switch system, but also all the intermediate positions of the driven system. AC1429 Specifications Resistance: 5kΩ (R5K) Revolutions: 10 (S10) AC Dimentions IA0090 Motor Gearbox 3.1" 6.2" 6.9" 7.87" 5.79" 5.05" 4.88" 7.55" 6.61" 6.55" 4.72" 5.94" 12.64" Munters Corporation, March 2017 QM1235r1 5

6 Installation Instructions Mounting the IA0090 Motor Gearbox. Mount the IA0090 motor gearbox according to the following instructions: Always use an allowed mounting position as shown in image 3.1.! CAUTION Please ensure that the IA0090 is mounted securely, so that the building structure can sufficiently absorb the forces applied.! Attention: When mounting the IA0090, ensure that the motor cover remains accessible so you will have no problems connecting, setting and operating the IA0090 *Please observe the following allowed mounting positions when installing the IA0090 Motor Gearbox Image 2.1 Use the M10 bolt and washer from the mounting kit to mount the plates to the gearbox. Mounting IA0090: Belt Drum - Wall Mount Mount the mounting plate for wall assembly to the IA0090 as follows: IA0090, ACTUATOR MOUNTING BRACKET M10 bolt M10 SPLITLOCK WASHER M10x20 BOLT 6 QM1235r1 Munters Corporation, March 2017

7 Chapter 2 Installation Instructions Mounting IA0090: Belt Drum - Ceiling Mount (Configuration 1) Mount the square mounting plate to the IA0090 by choosing option 1 (side) or 2 (foot). IA0090, ACTUATOR MOUNTING BRACKET M10 SPLITLOCK WASHER M10x20 BOLT Configuration Mounting the Drum, Winch Belt and Couplings Mount the drum, winch belt (single or double) and couplings for the IA0090 as follows: KEY NUT DOUBLE DRUM DISC BELT (2) DRUM SPACERS M6x80 BOLT SINGLE DRUM DISC Munters Corporation, March 2017 QM1235r1 7

8 Chapter 2 Installation Instructions 2.3 Pre-winding the Winch Belt onto the Belt Drum To safely use the belt drum and winch belt of the IA0090 it is necessary to pre-wind the belt at least ½ a revolution onto the drum. Belt drum with single or double belt: At least ½ revolution! CAUTION Not pre-winding the winch belt may result in injury at high belt or drum loads. 8 QM1235r1 Munters Corporation, March 2017

9 Connection and Operations Connection and Operation: Abbreviations Symbol A B CW (A) CCW (B) ESU K1 K2 Description Endposition A Endposition B Clockwise rotational direction (A) Counterclockwise rotational direction (B) Limit switch system Connection block Connection block Potentiometer L1, L2 Power source M N P PS Electric motor Neutral conductor Potentiometer Potentiometer installation set P71, P72* Contacts for automatic control (open or closed). PE Q41 S1 S11 S12 S21 S22 S111 U1 V1 W1 Z1 Z2 PTO R * Suitable for inductive load of 115/220 V - 2,5 A Ground (Earth Contact) Motor Safety Switch Toggle switch (3 positions) Duty switch limit switch system A Duty switch limit switch system B Safety switch limit switch system A Safety switch limit switch system B Manual switch Stop - Open - Close - Automatic Motor connection (U1) Motor connection (V1) Motor connection (W1) Gear Wheel Threaded Shaft (Potentiometer Set) Gear Wheel Potentiometer Shaft (Potentiometer Set) Protection Thermal Overload (Switch) Relay 3.2 Connecting the control componets: Switch Materials and cable lengths ATTENTION: Please use only suitable control components and switch materials. Make sure you are using the correct equipment by consulting the information on the control componets and switch materials. 3.3 OVERVIEW: Connections and Elements for Operating & Setting The overview in image shows the most important connections, parts and elements for operating and setting a IA0090 motor gearbox. As shown in image 3.3.1, remove the limit switch cover of the gearbox. TIP: Cover in image is also removed for a complete overview. However it is not nessesary to remove cover in this manual. Munters Corporation, March 2017 QM1235r1 9

10 Chapter 3 Connection and Operations Unscrew the four bolts and remove the limit switch cover while the gasket stays in place. 1. Limit switch cover 2. Gasket 3. Bolts 4. Cover electric motor Image The overview of a IA0090 motor gearbox. The detailed diagrams for connecting are shown in Step 3.5 Image QM1235r1 Munters Corporation, March 2017

11 Chapter 3 Connection and Operations 3.4 Rotational Directions and End Positions IA0090 Motor Gearbox The rotational direction for the IA0090 is Clockwise [CW] (A) which is twords the motor and Counter Clockwise [CCW] (B) which is away from the motor. Also visable are the corresponding limit switches for setting the end positions A and B. See figure below. Based on where the IA0090 and inlets are mounted and the direction the belt is wrapped on the drum, determine which direction will be open and which will be close. 3.5 Wiring Diagrams IA0090 Motor Gearbox Two wiring diagrams are applicable during installing and setting of the IA0090 gearbox. A temporary and a permanent diagram are used in a number of steps according to Step 3.5. Temporary connections (diagram 3.5.2): This is only used for setting switch, according to Step 3.6, prior to making the permanent connections of the IA0090 gearbox. Therefor a Temporary Power Cable is connected to the switch. Permanent connections (diagram 3.5.4): Make the permanent connections of the IA0090 gearbox after setting of the switch. TIP: If the operation of position feedback is applicable, installation and setting of a potentiometer (P) is done separately in Step 3.7 and Step 3.8.! CAUTION The IA0090 motor gearbox is standard delivered with switch S1 in stop position. Switch S1 is still in STOP position when starting temporary or permanent connections! S1 Stop! Munters Corporation, March 2017 QM1235r1 11

12 Chapter 3 Connection and Operations Connect the Temporary Power Cable. The image and the diagram below show the connections of a Temporary Power Cable. Image IA0090 Image Go to Step 3.6 and set the Limit Switch System prior to the permanent connections. Remove the Temporary Power Cable. 12 QM1235r1 Munters Corporation, March 2017

13 Chapter 3 Connection and Operations Make the permanent connections. The image and the diagram below show the permanent connections of the IA0090 gearbox. CCW (Counter Clockwise) CW (Clockwise) GROUND NEUTRAL Image Diagram * Suitable for inductive load of 115V - 2,5 A IA0090 ATTENTION: When setting the Limit Switch after the permanent connections, make sure that S111 and P71 (or equivalent parts) are configured toprovide power to L1 (13) of connection block K1! TIP: Reverse the direction of rotation of the IA0090 if desired. The direction of rotation can be turned by changing connections 12 and 13 (L2 and L1) in the connection block K1. Munters Corporation, March 2017 QM1235r1 13

14 Chapter 3 Connection and Operations 3.6 Setting the Limit switch system Delivery: Make the connections from the controller to the actuator terminal block (K1) depending on which direction is Open and which is Close. See Image Terminal Block (K1) Threaded Shaft End Position (B) End Position (A) Toggle Switch (S1) Image Textured Brass Nut Set Screws in Adjusting Ring Setting the Limits: See Image Put switch (S1) into Stop position. 2. Apply power to the Clockwise [CW] (A) terminal Find the Allen Wrench that ships with the actuator. 4. Loosen the (2) Set Screws on each Adjusting Ring, at each end of the threaded shaft. Setting the Clockwise [CW] (A) limit: 1. Put switch (S1) into CW (auto) position. Image When end position [CW] (A) is reached put switch (S1) back to Stop. 3. On the [CW] (A) end, turn the Textured Brass Nut hand tight against the stop. 4. Now turn the Adjusting Ring over the Textured Brass Nut so far, that the working switch is just connected by the long Adjusting Screw. 5. Now tighten the Set Screws firmly on the Textured Brass Nut. The Adjusting Ring cannot turn on the Brass Nut anymore. Setting the Counter Clockwise [CCW] (B) limit: 1. Put switch (S1) into CCW position. 2. When end position [CCW] (B) is reached put switch (S1) back to Stop. 3. On the [CCW] (B) end, turn the Textured Brass Nut hand tight against the stop. 4. Now turn the Adjusting Ring over the Textured Brass Nut so far, that the working switch is just contacted by the long Adjusting Screw. 5. Now tighten the Set Screws firmly on the Textured Brass Nut. The Adjusting Ring cannot turn on the Brass Nut anymore. The Limits are now set. 14 QM1235r1 Munters Corporation, March 2017

15 Chapter 3 Connection and Operations ATTENTION: If the motor gearbox is manual operated by means of the hexagon socket in the electric motor shaft, with an limit switch system which is set, it has to be checked that the end positions of the system will not be exceeded. This can cause damage to the limit switch system, as a result of which the limit switch system will not function well anymore. Operating mode Make sure the switch S1 is put in CW (A)/Auto position when permanent connections are done and setting of the Switch is finished. Place the limit switch cover1, with the gasket 2 still in place, and mount it with the four bolts. See image Image TIP: If the feedback option is applicable, then first install and set the potentiometer (P) according to Step 3.4 and Step 3.5. Munters Corporation, March 2017 QM1235r1 15

16 Chapter 3 Connection and Operations 3.7 Potentiometer Installation Set: Installation For an IA0090P, the Potentiometer set comes pre-installed in the unit for a typical installation with a 1m belt we recommend using the gears Z1 25 and Z Slide Potentiometer with gear towards the other gear without turning the shaft of the pot, so that the teeth on each gear nest together and tighten the pot nut with the hex key wrench. See Figure A. 2. The Potentiometer is pre-wired to the terminal bock K2. Make the connections between the controller and terminal block K2. See Figure B. If the Pot is changing voltage from low in the open position to high in the closed position then reverse the red and black wire on the controller side of terminal block K2. The Potentiometer installation is now complete. For a 2m belt use gear?? on the??? shaft. For a 3m belt use gear?? on the??? shaft. Potentiometer with Gear Gear on IA Shaft Figure A Terminal Block K2 RED WHITE BLACK Figure B 16 QM1235r1 Munters Corporation, March 2017

17 Chapter 3 Connection and Operations 3.8 Potentiometer table IA0090 motor gearbox (i=1,0) The table below can be used to select the necessary gearwheels when fitting a potentiometer and installation set in an IA0090 motor gearbox. The table shows the maximum number of revolutions of the drive shaft of the IA0090 motor gearbox. A range of 9 revolutions of the potentiometer has been chosen for maximum precision and sufficient reserve rotations when using a potentiometer. If the desired number of revolutions falls below the minimum value given, a 5-turn potentiometer may be used. In that case, the values in the table that give the maximum number of revolutions of the drive, should be divided by 2. IA0090 Munters Corporation, March 2017 QM1235r1 17

18 Maintenance Maintenance IA0090 Motor Gearbox Regularly check your IA0090 motor gearbox for operation performance and possible grease leakage. Inform your installer in case of grease leakage. Lubricant IA0090 SPH grease 1,9 lb IA Actuator by Munters Corporation, Lansing, Michigan U.S.A Munters Europe AB, Isafjordsgatan 1, P.O. Box 1150, SE Kista, Sweden. Phone , Fax Munters Corporation 2691 Ena Drive Lansing, MI U.S.A. Phone , Fax Australia Munters Pty Limited, Phone , Brazil Munters Brasil Industria e Comercio Ltda, Phone , Canada/US Munters Corporation Lansing, MI Phone , China Munters Air Treatment Equipment (Beijing) Co. Ltd, Phone , Denmark Munters A/S, Phone , India Munters India, Phone , Indonesia Munters, Phone , Italy Munters Italy S.p.A., Chiusavecchia, Phone , Japan Munters K.K., Phone , Korea Munters Korea Co. Ltd., Phone , Mexico Munters Mexico, Phone , Russia Munters AB, Phone , Singapore Munters Pte Ltd., Phone , South Africa and Sub-Sahara Countries Munters (Pty) Ltd., Phone , Spain Munters Spain S.A., Phone , Sweden Munters AB, Phone , Thailand Munters Co. Ltd., Phone , Turkey Munters Form Endüstri Sistemleri A.Ş, Phone , USA Munters Corporation, Lansing MI Phone , Vietnam Munters Vietnam, Phone , Export & Other countries Munters Italy S.p.A., Chiusavecchia Phone QM1235r1 Munters Corporation, March 2017