TOOLS REQUIRED: Crimping tool A/C Recovery Unit Wrench set up to 1 ¼ 4 Hole saw
|
|
- Rafe Franklin
- 5 years ago
- Views:
Transcription
1 INSTALL INSTRUCTIONS PT-A-401 HVAC UNIT for CHEVROLET/GMC VAN (For 2007 ALL WHITE Prisoner Transport Inserts ONLY) Not Recommended for diesel engine application because of lack of space needed for ac fittings. Warning do not attempt to install A/C units unless you are experienced with servicing A/C systems! TOOLS REQUIRED: Crimping tool A/C Recovery Unit Wrench set up to 1 ¼ 4 Hole saw ½ Power drill 3/8 Drive Socket set 3/8 Drive Ratcheting wrench ½ Impact gun PARTS AND HARDWARE: QTY DESCRIPTION PART# Wire ties GSM ft. 1/8 x 9/16 Black Gimp PRM HVAC Hose Clamp GSM Heater Hose 45 Y fitting PRM Water N/C Heater control valve PRM Vacuum Solenoid 12volt PRM ft. Vacuum Hose 5/32 PRM Vacuum T fitting PRM Adjustable steel heater hose clamp PRM ft. #6 AC Hose High Side PRM ft. #10 AC Hose Low Side PRM ft. 5/8 Heater hose PRM Low Side T Block fitting PRM High Side T Block fitting PRM #10FO x #10BL Straight AC fitting PRM #10FO x #10BL 90 AC fitting PRM # 6FO x #6BL 90 AC Fitting PRM ft. HVAC Unit drain hose PRM On/Off rocker switch C-SW-1 1 On/Off/On rocker switch C-SW-2 1 HVAC Unit PRM HVAC unit L mount bracket CM ½ Y Duct Connectors PRM Hose Clamps GSM ½ Air Duct Hose (32 foot length) PRM Ceiling Vent Cover Brackets KKM mm-1.25 x 65mm HHCS GSM /16 Flat washer GSM
2 INSTALLATION: 1. REAR EVAPORATOR MOUNTING: A. Position rear AC/Heat evaporator blower behind wheel well on driver side. Note: Install prior to transport insert. This photo shows rear bulkhead position. D B. Mark location for drain hose and cut ¾ hole with hole saw. Note: Silicone hole from underneath when mounting is complete. C. Drill 1/8 and screw down floor mount bracket with #10 x ¾ sheet metal screw. D. Drill ¼ hole and bolt upper bracket to inner body sheet metal with ¼ x ¾ hex bolt. B C 2. AIR DUCT HOSE INSTALLATION: (This step is done PRIOR to transport insert installation) A. Attach duct hoses to evaporator blower and run to ceiling. B. Note: Photo 3 shows complete duct hose assembly. A C. Duct hoses should be temporarily attached to ceiling in approximate location of ceiling vents. Hoses to be pulled through ceiling holes when ceiling is installed. D. Attach vent to ceiling with #10 x ¾ Phillips flat head sheet metal screws 2
3 3. CUT NECESSARY HOLES: Always check under floor for obstructions (Re. Hoses or harnesses). Determine location on vehicles floor to drill hole. Hole must be forward of driver side wheel well. Cut 4 hole on driver side floor of van. Apply rubber edge molding provided around drilled hole. Note: Hole in floor of van will need to be sealed with silicon when installation is complete 4. ROUTE HOSES: Start under hood of van and route all AC and Heat hoses to HVAC Unit through previously cut hole. Avoid running hoses on or around sharp edges. (Use supplied edge molding if necessary) Route AC/Heat unit hoses through hole in floor of van. At this time focus on HVAC connections under hood of van. Note: Do not tie hoses to brake lines, fuel lines or exhaust pipes. Tie or bolt to frame rail. 5. HEATER HOSES AND COMPONENTS: (Refer to Plumbing Diagram) Drain coolant from system. Locate heater hoses coming from factory heater core. Determine flow of water through factory system. Heater Hose Connections at Engine Note: Proper flow is necessary to acquire optimal performance of HVAC unit. With system drained, cut input hose to Heater Core. Attach Heater Y to ends of cut hose with 45 portion of Y going with flow of water through system. Attach supplied 2 ft. section of Heater hose onto remaining part of Heater Y Other side of 2 ft. section of Heater Hose will then go to Heater control valve. 3
4 Heater Control Valve has an arrow displaying direction of flow. Secure 2 ft. section onto top inlet of Heater Control Valve using Adjustable Steel Hose Clamps. Secure 1 st - 20 ft. section of Heater Hose to outlet of Heater Control Valve using adjustable steel hose clamps. Cut output hose from heater core. Attach Heater Y to ends of cut hose with 45 portion of Y going with flow of water through system. Attach 2 nd - 20 ft. section of Heater Hose to 45 portion of Y. Secure with Adjustable Steel Hose Clamps. 6. HEATER CONTROL VACUUM SWITCH: Locate OEM vacuum. Cut line and insert Vacuum T Re-attach cut Vacuum hose to sides of Vacuum T. Attach supplied Vacuum hose to bottom of Vacuum T. Mount Vacuum Solenoid in area shown in photo. Attach Vacuum hose to top inlet of Vacuum Solenoid. Secure with supplied 4 Wire Ties. Attach cut portion of Vacuum Hose to Vacuum Solenoid and route to Heater control Valve. Secure each end with 4 Wire Ties. Vacuum Solenoid has (2) ¼ spade terminals. One end needs to be grounded. The other end runs through supplied switch. Use 14ga Dark Blue as power out to the Vacuum Solenoid. (10amps) 7. LOW SIDE AIR CONDITIONING: (Refer to Plumbing Diagram) Separate Low side AC connection near OEM evaporator. Insert supplied Low Side T block fitting (PRM97447) between the separated fittings and reattach using metric bolt and washer. Crimp #10FO x #10BL 90 AC fitting onto #10 Low Side AC hose and attach to Low Side T block fitting previously installed. Be sure all connections are tightly secure. 4
5 Low Side T Block AC fitting connection with #10FO x #10BL 90 AC fitting High Side T Block AC fitting connection with #6FO x #6BL 90 AC fitting 5
6 8. HIGH SIDE AIR CONDITIONING: (Refer to Plumbing Diagram) Separate High side AC connection near OEM evaporator. Insert High Side T Block fitting (PRM97448) between separated fittings and reattach using metric Bolt and washer. Crimp #6FO x #6BL 90 AC fitting onto #6 High Side AC hose and attach to High Side T block fitting previously installed. Be sure all connections are tightly secure. 9. AC / HEAT UNIT: (Refer to Plumbing Diagram) Attach 2 ½ black duct hoses to plenum w/ (4) 2 ½ outlets located on HVAC unit using 2 ½ adjustable steel hose clamps. Route 2 ½ black duct hoses up driver sidewall of van in the area between the rear wheel well and the gas fill. Individually wire tie hoses in the corner of the vans wall and ceiling using 15 supplied wire ties being sure to fully stretch hoses. Wire tie supplied ½ Clear Drain Hose to plastic drain cap on HVAC Unit. Route hoses into HVAC access on driver side bench of Insert. Route Clear Drain Hose to hole in floor of Van. Cut to length and wire tie under vehicle. Wire AC / Heat Unit. Wires are as follows: Orange - High Fan Yellow Low Fan Black Ground Red Not used (Cap off) Connect wires, loom, and run to area where switching will be installed. Cut AC and Heat hoses to length. Crimp #10FO x #10BL Straight AC fitting to 18-foot Section of #10 Low Side AC hose. Attach to HVAC unit. Crimp #6FO x #6BL 90 AC fitting to 18-foot section of #6 High Side AC hose. Attach to HVAC unit. Attach Heater hoses to HVAC unit using adjustable steel hose clamps. Center unit in access cutout and flush to lip in bench. Screw HVAC unit strap to floor of van using #10 x ¾ sheet metal screws. Silicone hole in floor of Van. 10. Recharge system with 3.5 to 4 lbs refrigerant and 2 ounces refrigerant oil. Vacuum Hose PRM97418 Vacuum Tee PRM97451 Heater Tees PRM
7 Wiring Kit HS-WS3 2 ½ Hose Clamp GSM20040 HVAC Unit PRM97484 Heater Control Valve PRM97411 Vacuum Solenoid PRM97412 Drain Hose PRM97449 #6FO x #6BL 90 AC fitting PRM97405 #10-90 Degree PRM
8 #6FO x #6BL Straight AC Fitting PRM97403 #10FO x #10BL Straight AC Fitting PRM97404 High Side T Block PRM97448 Low Side T Block PRM
9 HEAT DIAGRAM CHEVROLET VANS 45 Heater Y 9
10 AIR CONDITIONING DIAGRAM CHEVROLET VANS 10
11 REAR AC / HEAT WIRING DIAGRAM 11
INSTALLATION INSTRUCTIONS PT-A HEAT/AC STANDARD KIT FORD E-SERIES VANS
INSTALLATION INSTRUCTIONS PT-A-402 - HEAT/AC STANDARD KIT 2007-2014 FORD E-SERIES VANS with Gas engine (To be used with 2007 and newer Prisoner Transport Inserts ONLY) Warning do not attempt to install
More informationINSTALL INSTRUCTIONS KK-S-HVAC SPRINTER VAN REAR HVAC SYSTEM
INSTALL INSTRUCTIONS KK-S-HVAC-2 2007-2014 SPRINTER VAN REAR HVAC SYSTEM TOOLS REQUIRED: Aeroquip (#FT1357) Pliers A/C Refrigerant Charging machine Refrigerant Hose Cutter Open-end wrench set (up to 1
More informationWarning Do not attempt to install A/C units unless you are experienced with servicing A/C systems! Wire Cutter / Crimper Socket set
INSTALLATION INSTRUCTIONS PT-A-405 Rear HVAC System for 2014-2018 RAM PROMASTER with OEM rear AC/Heat Prep Package Fittings For Installation with Havis Prisoner Transport Insert Warning Do not attempt
More informationJOHN DEERE GATOR HPX/XUV 2 PASSENGER HEATER INSTALLATION INSTRUCTIONS (p/n: 9PH20S30)
P. 1 of 12 JOHN DEERE GATOR HPX/XUV 2 PASSENGER HEATER INSTALLATION INSTRUCTIONS (p/n: 9PH20S30) Item: Qty: Description: 1 2 1 x 1 x 5/8 Tee Fitting 2 2 Plastic Snap-in Hose Grommet 3 4 1-1/2" Hose Clamps
More informationINSTALLATION INSTRUCTIONS John Deere One Series; 1023E, 1025R and 1026R Models A HEATER KIT. Figure 1 (General Layout and Parts I.D.
A-11978 HEATER KIT Figure 1 (General Layout and Parts I.D.) Read these instructions and identify all components. Please retain these instructions for future reference and parts ordering information. Refer
More informationCamaro A/C Install Instructions
1967-1968 Camaro A/C Install Instructions This kit is designed for the 1967-1968 non A/C equipped Camaro. This kit can be used with or without Astro vents Step One Remove the following factory components:
More informationan ISO 9001:2008 Registered Company ShortPac HEAT/COOL (05000-QUX-A/05000-VUX-A)
an ISO 9001:2008 Registered Company ShortPac (05000-QUX-A/05000-VUX-A) 18865 GOLL ST. - SAN ANTONIO, TX. - 78266 - ph.210-654-7171 - fax 210-654-3113 900499 REV C 3/7/14, ShortPac EVAPORATOR KIT PG 1 OF
More informationHeater with Air Conditioning. E-Series Ford Aeromaster
Service Guide Heater with Air Conditioning E-Series Ford Aeromaster Contents Blower Motor...2 Plenum Removal...3 Control Module...6 Servo Motors...8 Coolant Valve and Servo Motor...8 Evaporator Recirculation
More informationPERFECT FIT SERIES IN-DASH HEAT/ COOL/ DEFROST CHEVROLET CHEVELLE/ EL CAMINO NOTE: INSTRUCTIONS DEPICT CHEVELLE
specializing in AIR CONDITIONING, PARTS AND SYSTEMS for your classic vehicle PERFECT FIT SERIES IN-DASH HEAT/ COOL/ DEFROST 1964-65 CHEVROLET CHEVELLE/ EL CAMINO NOTE: INSTRUCTIONS DEPICT CHEVELLE CONTROL
More informationPERFECT FIT SERIES IN-DASH HEAT/ COOL/ DEFROST CHEVROLET NOVA
specializing in AIR CONDITIONING, PARTS AND SYSTEMS for your classic PERFECT FIT SERIES IN-DASH HEAT/ COOL/ DEFROST 1966-67 CHEVROLET NOVA CONTROL & OPERATING INSTRUCTIONS The controls on your new Perfect
More informationHeater for BRP Commander. Caution: Before using this product, read this manual and follow all safety instructions. Owner s Manual
Owner s Manual Model: Can Am Commander Heater for BRP Commander Caution: Before using this product, read this manual and follow all safety instructions. Safety Instructions Kit Contents Tool Requirement
More informationspecializing in AIR CONDITIONING, PARTS AND SYSTEMS for your classic hi l PERFECT FIT SERIES IN-DASH HEAT/ COOL/ DEFROST FORD TRUCK
specializing in AIR CONDITIONING, PARTS AND SYSTEMS for your classic hi l PERFECT FIT SERIES IN-DASH HEAT/ COOL/ DEFROST 1967-72 FORD TRUCK CONTROL & OPERATING INSTRUCTIONS The controls on your new Perfect
More informationKawasaki Teryx Firestorm Heater Kit Instructions.
Please read all instructions before beginning installation. When working on cooling systems always allow vehicles to cool to avoid being burned or scalded by hot coolant. Always disconnect vehicle s negative
More informationBC BRONCOS AIR CONDITIONING UNIT
BC BRONCOS AIR CONDITIONING UNIT CAUTION If you are not familiar with the principals of air conditioning, have an authorized air conditioning technician evacuate and charge the system. Serious damage to
More informationPERFECT FIT IN-DASH HEAT/ COOL/ DEFROST FORD PICKUP
specializing in AIR CONDITIONING, PARTS AND SYSTEMS for your classic vehicle PERFECT FIT IN-DASH HEAT/ COOL/ DEFROST 1960-66 FORD PICKUP CONTROL & OPERATING INSTRUCTIONS The controls on your new Perfect
More informationan ISO 9001:2008 Registered Company GOLL ST. - SAN ANTONIO, TX ph fax MINI SPACE SAVER HEAT /COOL
an ISO 9001:2008 Registered Company 18865 GOLL ST. - SAN ANTONIO, TX. - 78266 - ph.210-654-7171 - fax 210-654-3113 MINI SPACE SAVER HEAT /COOL 01000-QUX-A 01000-VUX-A 900101-VUX-A REV C 3/5/14, MINI SPACE
More informationBlueHeat Coolant Heater
BlueHeat Coolant Heater Dodge Ram 500 / 3500 003 / 004-5. Liter Gasoline 003 / 006-5.9 Liter Diesel 00 6. Liter Diesel Installation Instructions DOC P/N 500068B KIT P/N 5000498C PRELIMINARY INFORMATION
More informationMOUNTING INSTRUCTIONS
John Deere HPX and XUV Heater Kit 4-14916 MOUNTING INSTRUCTIONS With replacement parts drawing BOX 70 LITCHFIELD, MINNESOTA 55355-0070 (320) 693-3221 Fax: (320) 693-7252 Visit our web site at: www.800cabline.com
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publication No. HEATER KIT P/N 0SE01-HL3-102 (SXS700M2/M4) P/N 0SE01-HL3-103 (SXS700M2D/M4D) SXS700M2/M2D/M4/M4D MII 14607-15172 Issue Date REVISED: June
More informationINSTALLATION INSTRUCTIONS
Accessory Application Publication No. INSTALLATION INSTRUCTIONS HEATER KIT P/N 0SE01-HL3-101 SXS700M4/M2 Honda Dealer: Please give a copy of these instructions to your customer. PARTS LIST REPAIR KIT (P/N
More informationPERFECT FIT IN-DASH HEAT/ COOL/ DEFROST PLYMOUTH BELVEDERE
PERFECT FIT IN-DASH HEAT/ COOL/ DEFROST 1966-67 PLYMOUTH BELVEDERE CONTROL & OPERATING INSTRUCTIONS The controls on your new Perfect Fit system. Offers complete comfort capabilities in virtually every
More informationPERFECT FIT IN-DASH HEAT/ COOL/ DEFROST 1968 CHEVROLET IMPALA
specializing in AIR CONDITIONING, PARTS AND SYSTEMS for your classic vehicle PERFECT FIT IN-DASH HEAT/ COOL/ DEFROST 1968 CHEVROLET IMPALA CONTROL & OPERATING INSTRUCTIONS The controls on your new Perfect
More informationHEAT/ COOL/ DEFROST FORD THUNDERBIRD
specializing in AIR CONDITIONING, PARTS AND SYSTEMS for your classic vehicle PERFECT FIT IN-DASH HEAT/ COOL/ DEFROST 1964-66 FORD THUNDERBIRD CONTROL & OPERATING INSTRUCTIONS The controls on your new Perfect
More informationA HEATER KIT With Diesel Engine Connection Fittings
A-12142 HEATER KIT With Diesel Engine Connection Fittings Figure 1 (General Layout and Parts I.D.) Page 1 of 6 Read these instructions and identify all components. Please retain these instructions for
More informationCOMPAC GEN II HEAT/COOL VUX-A. an ISO 9001:2008 Registered Company #10 SUCTION HOSE COMPRESSOR #8 DISCHARGE HOSE EVAPORATOR DRIER CONDENSER
an ISO 900:2008 Registered Company COMPAC GEN II HEAT/COOL 68000-VUX-A EVAPORATOR #0 SUCTION HOSE COMPRESSOR #8 DISCHARGE HOSE DRIER #6 LIQUID LINE CONDENSER 90680-VUX-A REV E 2/28/4, INST. GEN II COMPAC
More informationHVAC Module Assembly Replacement
ALLDATA Online - 2006 Chevy Truck Equinox FWD V6-3.4L VIN F - HVAC Module... Page 1 of 12 Home Account Contact ALLDATA Log Out Help TINO TORRES Select Vehicle New TSBs Technician's Reference Component
More informationan ISO 9001:2008 Registered Company MINI SPACE SAVER HEAT /COOL/DEFROST QUZ-A VUZ-A
an ISO 900:2008 Registered Company MINI SPACE SAVER HEAT /COOL/DEFROST 0000-QUZ-A 0000-VUZ-A 8865 GOLL ST. - SAN ANTONIO, TX. - 78266 - ph.20-654-77 - fax 20-654-33 90000-VUZ-A REV E 3/5/4, MINI SPACE
More informationHeating and ventilation system,
Page 1 of 24 87-151 Heating and ventilation system, servicing Instrument panel air outlets and air guide ducts CAUTION! Before working on the electrical system: Obtain security code for anti-theft radio.
More informationMINI SLIMLINE COOL VUY-A VUY-A
an ISO 900:2008 Registered Company MINI SLIMLINE COOL 030-VUY-A 040-VUY-A 8865 GOLL ST. - SAN ANTONIO, TX. - 78266 ph.20-654-77 - fax 20-654-33 900302 REV D 0/28/4, MINI SLIMLINE COOL PG OF Table of Contents
More informationAuxiliary HVAC RAM ProMaster. Standard Tie-in Extreme Climate System
Auxiliary HVAC RAM ProMaster Standard Tie-in Extreme Climate System Auxiliary HVAC High performance aftermarket heating and cooling systems engineered for vehicle specific platforms that minimize install
More informationProduct Support Bulletin
MODEL: SUBJECT: CONVENTIONAL, W/ C7 CAT ENGINE WEBASTO TSL-17 HEATER Body DATE: APRIL 13, 2004 INDEX: 6 PAGE: 1 OF 16 Before you start this procedure, perform Freightliner Service Bulletin #20-7 first.
More informationChevrolet Pickup Condenser Kit with Drier with Condenser Mounted Forward From Stock Position (021553)
an ISO 900:2008 Registered Company 97-55 Chevrolet Pickup Condenser Kit with Drier with Condenser Mounted 3 8 Forward From Stock Position (02553) 8865 Goll St. San Antonio, TX 78266 Phone: 20-65-77 Fax:
More informationInstallation Instructions
Installation Instructions Outdoor Installation Kit Models AD250 & AW250 Part No. 24097 Qualifications for installation of the kit: You must be able to read and understand all instructions provided with
More informationChevrolet Corvette Auxiliary Electric Condenser Fan Kit with Trinary Switch ( CCA)
an ISO 900:2008 Registered Company 968-76 Chevrolet Corvette Auxiliary Electric Condenser Fan Kit with Trinary Switch (302686-CCA) 8865 Goll St. San Antonio, TX 78266 Phone: 800-862-6658 Sales: sales@vintageair.com
More informationSUPER GEN II HEAT/COOL VUX-A. an ISO 9001:2008 Registered Company EVAPORATOR #10 SUCTION HOSE COMPRESSOR #8 DISCHARGE HOSE DRIER CONDENSER
an ISO 900:2008 Registered Company SUPER GEN II HEAT/COOL 6005-VUX-A EVAPORATOR #0 SUCTION HOSE COMPRESSOR #8 DISCHARGE HOSE DRIER #6 LIQUID LINE CONDENSER 90606-VUX-A REV E 2/28/4, INST. GEN II SUPER
More informationHVAC Module Assembly Replacement. Tools Required. J A Halogen Leak Detector. Removal Procedure
2005 Pontiac Grand AM V6-3.4L VIN E Page 1 Housing Assembly HVAC: Service and Repair The content of this article reflects the changes identified in TSB Bulletin No. #06-01-37-002 dated January 18, 2006.
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. ENGINE BLOCK ELEMENT AII 24284 Issue Date DEC 2002 PARTS LIST Engine block heater Aluminum washer Heater harness Protective cap 20 Long
More informationPERFECT FIT IN-DASH HEAT/ COOL/ DEFROST EARLY 1955 CHEVROLET PICKUP
specializing in AIR CONDITIONING, PARTS AND SYSTEMS for your classic vehicle PERFECT FIT IN-DASH HEAT/ COOL/ DEFROST 1947 - EARLY 1955 CHEVROLET PICKUP CONTROL & OPERATING INSTRUCTIONS The controls on
More informationPERFECT FIT SERIES IN-DASH HEAT/ COOL/ DEFROST MUSTANG
specializing in AIR CONDITIONING, PARTS AND SYSTEMS for your classic vehicle PERFECT FIT SERIES IN-DASH HEAT/ COOL/ DEFROST 1965-66 MUSTANG CONTROL & OPERATING INSTRUCTIONS The controls on your new Perfect
More informationINSTALLATION AND COMMISSIONING MANUAL. Neos 100S Integra 20X, 30S, 35X, 40X, 50X
Installation Truck Refrigeration & Commissioning Manual: INSTALLATION AND COMMISSIONING MANUAL for Neos 100S Integra 20X, 30S, 35X, 40X, 50X Direct Drive Refrigeration Units 2017 Carrier Corporation Printed
More informationan ISO 9001:2008 Registered Company
an ISO 900:2008 Registered Company 964-67 Pontiac GTO Condenser Kit with Drier (0206) Please Note: Installation for 964 Models is covered on Pages 4-3 Installation for 965-67 Models is covered on Pages
More informationChevrolet Chevelle Condenser Kit with Drier (021166)
an ISO 900:008 Registered Company 964-67 Chevrolet Chevelle Condenser Kit with Drier (066) SS 8865 Goll St. San Antonio, TX 7866 Phone: 0-654-77 Fax: 0-654-33 www.vintageair.com 90366 REV D 08//5, PG OF
More informationSAF-T-LINER MVP-ER PARTS MANUAL. Heaters Section. Page 8-1. Heaters 10/96
Heaters Section Heaters Page 8-1 Heater Page 8-2 Heaters Heater Item Part Num. Number Qty. Description Notes 66001447 1 Heater - Front 1 85660310 1 Heater - Core, Assembly 2 85660311 1 Bottom - Assembly
More informationINSTALLATION INSTRUCTIONS WALL MOUNT LINER INSERT
Read and Save These Instructions All Hoods Must Be Installed By A Qualified Installer INSTALLATION INSTRUCTIONS WALL MOUNT LINER INSERT Read All Instructions Thoroughly Before Beginning Installation WARNING
More information1956 FORD F-100 TRUCK
an ISO 9001:2008 Registered Company INSTALLATION INSTRUCTIONS FOR 1956 FORD F-100 TRUCK HEAT/COOL/DEFROST 75456-LFZ-A 18865 GOLL ST. - SAN ANTONIO, TX. - 78266 - ph.210-654-7171 - fax 210-654-3113 905456-LFZ-A
More informationHeater Core Replacement
Page 1 of 14 2003 Chevrolet Impala : Heating, Ventilation, & Air Conditioning > Repair Instructions > Heater Core Replacement Heater Core Replacement HEATER CORE REPLACEMENT Tools Required J 38185 (Image
More informationINSTALLATION & OWNER S MANUAL
Rev. A, p. 1 of 8 INSTALLATION & OWNER S MANUAL HONDA PIONEER 700-2 AND 700-4 HEATER INSTALLATION p/n: 9PH20S64 The contents of this envelope are the property of the owner. Be sure to leave with the owner
More informationan ISO 9001:2015 Registered Company
an ISO 9001:2015 Registered Company Mark IV (672001-VHY) 18865 Goll St. San Antonio, TX 78266 Phone: 800-862-6658 Sales: sales@vintageair.com Tech Support: tech@vintageair.com www.vintageair.com 902001-VHY
More informationInstallation Instructions
PAGE 1 Installation Instructions Important information about your new a/c system. Please read the following directions prior to installing this a/c system. PN: CK6772-1CHPU 1967-1972 Chevy PU A/C Kit Contact
More informationINSTALLATION INSTRUCTIONS WALL MOUNT LINER INSERT
Read and Save These Instructions All Hoods Must Be Installed By A Qualified Installer INSTALLATION INSTRUCTIONS WALL MOUNT LINER INSERT Read All Instructions Thoroughly Before Beginning Installation WARNING
More informationINSTALLATION INSTRUCTIONS WALL MOUNT LINER INSERT
Read and Save These Instructions All Hoods Must Be Installed By A Qualified Installer INSTALLATION INSTRUCTIONS WALL MOUNT LINER INSERT Read All Instructions Thoroughly Before Beginning Installation WARNING
More informationDISTRIBUTION > HOUSING, HVAC > INSTALLATION > AIR INLET HOUSING
Page 1 of 6 Service Manual: HEATING & AIR CONDITIONING - Print Date: SERVICE INFORMATION - 2500 HD & 3500 HD DISTRIBUTION > HOUSING, HVAC > INSTALLATION > AIR INLET HOUSING Fig 1: Front Of Air Inlet Housing
More informationHeat Exchanger Block Replacement Instructions
Series 1-4 Gas-fired water boiler Heat Exchanger Block Replacement Instructions Ultra-80 S1-4 Heat Exchanger Block Replacement Kit, Part No. 383-500-773 Ultra-105 S1-4 Heat Exchanger Block Replacement
More informationINSTALLATION INSTRUCTIONS WALL MOUNT LINER INSERT
Read and Save These Instructions All Hoods Must Be Installed By A Qualified Installer INSTALLATION INSTRUCTIONS WALL MOUNT LINER INSERT Read All Instructions Thoroughly Before Beginning Installation WARNING
More informationFord Falcon, Ranchero Condenser Kit with Drier (014150)
an ISO 900:2008 Registered Company 964-65 Ford Falcon, Ranchero Condenser Kit with Drier (0450) 8865 Goll St. San Antonio, TX 78266 Phone: 20-654-77 Fax: 20-654-33 www.vintageair.com 903250 REV A 06/23/5,
More informationBlueHeat AirTop 2000 Heater
BlueHeat AirTop 000 Heater Air Heater Installation Manual Ford E-Series 6.0L Diesel Beginning Model Year: 006 Special instructions for these models Part locations may differ slightly dependent on the vehicle
More informationCABS/BLADES/ SPREADERS/ACCESSORIES
JOHN DEERE 3000 SERIES (4200/4300/4400) (4210/4310/4410) (3120/3320/3520/3720) JOHN DEERE 4000 SERIES (4500/4600/4700) (4510/4610/4710) (4120/4320/4520/4720) OPTIONAL AUXILIARY HEATER INSTALLATION (p/n
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. AII 41826 ENGINE BLOCK P/N 08T44-SNA-101 2010 ODYSSEY Issue Date JUNE 2009 PARTS LIST Engine block heater Aluminum washer NOTE Always use
More informationREFLECTOR PANS FOR HINGED ELEMENTS CONNECTOR BLOCK KIT TRIM RINGS FOR ABOVE PANS CONNECTOR BLOCK RANGE CORD REFLECTOR PANS FOR PLUG-IN ELEMENTS
*s are Subject to Change without Notice.* REFLECTOR PANS FOR HINGED ELEMENTS Heavy Chromed Steel Description 2-1040 6" UNIVERSAL $2.19 2-1041 8" UNIVERSAL $2.89 2-1050 6" GE/HOTPOINT $2.39 2-1051 8" GE/HOTPOINT
More informationCIRRUS AIRPLANE MAINTENANCE MANUAL
COOLING 1. DESCRIPTION On aircraft serials 183 and subsequent, an optional air condition system is available. This section contains the maintenance practices pertinent to this system. Cabin ventilation
More informationHeavy Duty Heater / Air Conditioner Model R-8545
Heavy Duty Heater / Air Conditioner Model R-8545 INSTALLATION INSTRUCTIONS NOTE 1. Please read instructions all the way through, making sure you have all the parts and tools 2. While working on or around
More informationPRELIMINARY INSTALLATION. Operation & Service Manual. Carrier Transicold Europe 03/09/07 Viento - Installation/Rev- #1/56
INSTALLATION Carrier Transicold Europe 03/09/07 Viento - Installation/Rev- #1/56 INSTALLATION Table of content Introduction...4 Preparation before installation...5 Vehicle partition... 6 Box preparation...7
More informationWASHER/DRYER CONTROL PANEL PARTS
WASHER/DRYER CONTROL PANEL PARTS WASHER/DRYER LAUNDRY SYSTEM 1 Literature Parts W10356098 Installation Instructions W10343071 Guide, Use & Care W10364010 Wiring Diagram W10343084 Energy Guide 2 3390688
More informatione Bath Fan with Light User s Guide
e Bath Fan with Light User s Guide abfl100rnl, BFL125RNL Item Stock Number(s): BFL100RNL, BFL125RNL IMPORTANT INSTRUCTIONS - OPERATING MANUAL READ AND SAVE THESE INSTRUCTIONS READ CAREFULLY BEFORE ATTEMPTING
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. AII 30320 ENGINE BLOCK 2006 CIVIC HYBRID P/N 08T44-SVB-100 Issue Date SEP 2005 PARTS LIST Engine block heater Aluminium washer Heater harness
More informationTechnical Manual. VFD / Cabinet Heater Upgrade 110 VAC Heater to 12 VDC Heater. Provided by: Chart Inc.
Technical Manual VFD / Cabinet Heater Upgrade 110 VAC Heater to 12 VDC Heater Provided by: Chart Inc. 407 7th Street NW New Prague, MN 56071 USA (800) 400-4683 Part Number 20977233 Rev. A 2016 Chart Inc.
More informationTOYOTA FJ-40 DIRECTIONS
PAGE 1 TOYOTA FJ-40 DIRECTIONS Please read the following directions prior to installing this a/c system. Contact us by email or phone if you need any assistance or information regarding this a/c system.
More informationChevrolet Impala Condenser Kit with Drier (021062)
an ISO 900:2008 Registered Company 96-63 Chevrolet Impala Condenser Kit with Drier (02062) 8865 Goll St. San Antonio, TX 78266 Phone: 20-654-77 Fax: 20-654-33 www.vintageair.com 90063 REV D 03/22/6, PG
More informationRead and Save These Instructions All Hoods Must Be Installed By A Qualified Installer
Read and Save These Instructions All Hoods Must Be Installed By A Qualified Installer INSTALLATION INSTRUCTIONS WALL MOUNT LINER INSERT Read All Instructions Thoroughly Before Beginning Installation WARNING
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS BUILT-IN BOTTOM MOUNT REFRIGERATOR/FREEZER DBRTGK72SS-GRILLE KIT (FOR designer SERIES ONLY) VIKING RANGE CORPORATION 111 Front Street Greenwood, Mississippi (MS) 38930 USA (662)
More informationWASHER/DRYER CONTROL PANEL PARTS For Models: LTE6234DQ5, LTE6234DT5 (Designer White) (Biscuit)
WASHER/DRYER CONTROL PANEL PARTS WASHER/DRYER LAUNDRY SYSTEM 1 Literature Parts Installation Instructions 8577199 English 3397634 Arabic Use & Care Guide 8578179 English 3405528 Arabic 8542752 Sheet, Cycle
More informationInstallation Instructions. For the 18 Built-In Dishwasher and Front Color Panels
Installation Instructions For the 18 Built-In Dishwasher and Front Color Panels Printed in USA 154232102 Before You Begin DO NOT INSTALL DISHWASHER UNTIL YOU HAVE READ ALL INSTRUCTIONS. FOR YOUR SAFETY,
More informationInstallation Manual. Truck Edition V-520 RT Series Model 10, 20, 30 and 50 Single Temperature Systems. TK IM (Rev.
Installation Manual Truck Edition V-520 RT Series Model 10, 20, 30 and 50 Single Temperature Systems TK 54987-1-IM (Rev. 2, 03/12) Installation Manual Truck Edition V-520 RT Series Models 10, 20, 30 and
More informationEasy installation. EZ80N EZ Fit Ventilation Fan INSTALLATION GUIDE READ AND SAVE THESE INSTRUCTIONS. Table of Contents
READ AND SAVE THESE INSTRUCTIONS EZ80N EZ Fit Ventilation Fan INSTALLATION GUIDE Easy installation Table of Contents Warnings and Cautions Operation Cleaning and Maintenance Troubleshooting Typical Installation
More informationSCC 201E Valid as of E21SE0404 up to E21SE... SCC 201E
Electrical unit Voltage 3 NAC 400V 50-60Hz 1 1 Control panel 2 2 Electrical installation 3 3 Clima Plus 4 4 Steam generator, Bypass 5 5 Hot air heating 6 6 Motor and fan wheel 7 7 Interior cabinet 8 8
More informationHome Stacked Washer/Dryer
Home Stacked Washer/Dryer Refer to Page 3 for Model Numbers Parts SWD443C_802107 www.comlaundry.com Part No. 802107R6 August 2014 Table of Contents Title Page Parts Ordering Information... 2 Serial Plate
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. ENGINE BLOCK P/N 08T44-SNA-100 2007 MDX BII 32728 Issue Date OCT 2006 PARTS LIST Engine block heater Aluminum washer Heater harness Protective
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. ENGINE BLOCK P/N 08T44-SNA-100 2008 MDX BII 37679 Issue Date AUG 2007 PARTS LIST Engine block heater Aluminum washer Heater harness Protective
More informationPage 1 of 5 #02-06-04-037F: DTC P0446 (Restricted/Blocked EVAP Vent Path) Set, Check Engine Light On (Replace Evaporative Emission (EVAP) Vent Valve Solenoid Assembly and Add/Relocate Filter Box Using
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS BUILT-IN BOTTOM MOUNT REFRIGERATOR/FREEZER BRTGK72SS-GRILLE KIT (FOR PROFESSIONAL SERIES ONLY) VIKING RANGE CORPORATION 111 Front Street Greenwood, Mississippi (MS) 38930 USA
More informationEquipment Alert. P-Trap Must Be Installed to Exhaust or Warranty will be Voided. Refer to this Manual for installation Instructions
Dry Assembled Elbows MUST Glue when Installed Exhaust Connection P-Trap Must Be Installed to Exhaust or Warranty will be Voided AA2360 Refer to this Manual for installation Instructions 2011 Midmark Corp.
More informationINSTALLATION AND OPERATION MANUAL
F OR I NGROUND P OOLS INSTALLATION AND OPERATION MANUAL How Solar Pool Heating Works Why SunHeater TM Works Best Using your pool pump, water is automatically pumped through the solar collectors. The water
More informationAn ibuy Stores Company
REVISED STARTING SERIAL NO. 060604 PARTS MANUAL Model SK-4 4 DOWNCUT CONCRETE/ASPHALT WALK BEHIND SAWS SKU NO. MODEL POWER OPTION 45400D SK4-9H HONDA ENGINE 9 HP GX0 45600D SK4-H HONDA ENGINE HP GX40 4800D
More informationEngine Block Heater Service Kits (Tank Type) 30RZ/33RZ/45RZ (CSG 649 Ford Powered) Standby Generator Sets
TT 880 INSTRUCTIONS 7/92 Engine Block Heater Service Kits (Tank Type) 30RZ/33RZ/45RZ (CSG 649 Ford Powered) Standby Generator Sets Model Voltage Kit No. All Models 120 276380 All Models 240 276381 This
More informationWASHER/DRYER CONTROL PANEL PARTS For Model: MET3800TW2 (White)
WASHER/DRYER CONTROL PANEL PARTS WASHER/DRYER LAUNDRY SYSTEM 1 Literature Parts W10222378 Installation Instructions W10196552 Use & Care Guide W10117755 Sheet, Cycle Feature W10114285 Wire Diagram 2 3390688
More informationREAD AND SAVE THESE INSTRUCTIONS READ CAREFULLY BEFORE ATTEMPTING TO ASSEMBLE, INSTALL, OPERATE OR MAINTAIN THE PRODUCT DESCRIBED. PROTECT YOURSELF AN
READ AND SAVE THESE INSTRUCTIONS READ CAREFULLY BEFORE ATTEMPTING TO ASSEMBLE, INSTALL, OPERATE OR MAINTAIN THE PRODUCT DESCRIBED. PROTECT YOURSELF AND OTHERS BY OBSERVING ALL SAFETY INFORMATION. FAILURE
More informationInstallation Manual. Truck Edition V-500 Series. TK IM (Rev. 3, 01/05) Copyright 2004 Thermo King Corp., Minneapolis, MN, U.S.A.
Installation Manual Truck Edition V-500 Series TK 51857-1-IM (Rev. 3, 01/05) Copyright 2004 Thermo King Corp., Minneapolis, MN, U.S.A. Introduction This manual was written to assist with the installation
More informationChevrolet Camaro Condenser Kit with Drier (021179)
an ISO 900:008 Registered Company 978-8 Chevrolet Camaro Condenser Kit with Drier (079) 8865 Goll St. San Antonio, TX 7866 Phone: 0-65-77 Fax: 0-65-33 www.vintageair.com 9085 REV C 03/8/6, PG OF 3 Table
More informationHomestyle Stacked Washer/Dryer
Homestyle Stacked Washer/Dryer Parts Refer to Page 3 for Model Numbers SWD443C_801802 www.alliancelaundry.com Part No. 801802R8 January 2018 Table of Contents Title Page Parts Ordering Information...
More informationSection 2 Safety, Tools and Equipment, Shop Practices Unit 5 Tools and Equipment
Section 2 Safety, Tools and Equipment, Shop Practices Unit 5 Tools and Equipment Unit Objectives After studying this chapter, you should be able to: Describe hand tools used by the air-conditioning, heating,
More informationSection 2 Safety, Tools and Equipment, Shop Practices Unit 5 Tools and Equipment. Unit Objectives 3/1/2012. General Hand Tools (1 of 6)
Section 2 Safety, Tools and Equipment, Shop Practices Unit 5 Tools and Equipment Unit Objectives After studying this chapter, you should be able to: Describe hand tools used by the air-conditioning, heating,
More informationINSTALLATION INSTRUCTIONS AH12 WALL MOUNT HOOD
Read and Save These Instructions All Hoods Must Be Installed By A Qualified Installer INSTALLATION INSTRUCTIONS AH12 WALL MOUNT HOOD Read All Instructions Thoroughly Before Beginning Installation WARNING
More informationInstallation Instructions
Installation Instructions Downdraft Vent Systems PVB94 PVB98 ZVB30 ZVB36 31-10728-8 11-14 GE 1 Safety Information If you have questions, call 800.GE.CARES or visit our website at: GEAppliances.com BEFORE
More informationMopit 4 Operator s / Service Manual
Mopit 4 Operator s / Service Manual FOR PARTS AND SERVICE 1-800-290-2833 To view Mopit 4 instructional videos scan this qr code with your smart phone. You can also find Mopit 4 instructional videos on
More informationInstallation Manual. NAD Truck Edition V-200 and V-300 Series. TK IM (Rev. 7, 02/12)
Installation Manual NAD Truck Edition V-200 and V-300 Series TK 51856-1-IM (Rev. 7, 02/12) Installation Manual NAD Truck Edition V-200 and V-300 Series TK 51856-1-IM (Rev. 7, 02/12) Copyright 2003 Thermo
More informationMP GS/GD 10 GAS. Toll Free Phone, (US & Canada): (800) Toll Free Fax, (US & Canada): (800)
MP GS/GD 0 GAS Toll Free Phone, (US & Canada): (800) 427-6668 Toll Free Fax, (US & Canada): (800) 36-7745 http://www.garland-group.com FORM # Moisture Plus Gas GS/GD0 (Rev 5) Page 2 FORM # Moisture Plus
More informationMopar B-Body Condenser Kit with Drier
an ISO 900:2008 Registered Company 966-70 Mopar B-Body Condenser Kit with 05066 Fits: Plymouth: Belvedere, Satellite, Road Runner (Except 970), GTX Dodge: Charger (Except 966-67), Coronet, Super Bee 8865
More informationWhen checking the vehicle for DTCs, the ECM may report one or more of the following DTCs set as current or in history: P0442, P0446, P0449 or P0455.
2006 GMC Sierra 5.3L Eng 1500 CHECK ENGINE LIGHT ON, FUEL TANK HARD TO FILL, DTCS P0442, P0446, P0455 OR P0449 SET (REPLACE EVAPORATIVE EMISSION (EVAP) VENT VALVE SOLENOID ASSEMBLY AND ADD/RELOCATE FILTER
More informationDocument ID: The EVAP canister vent solenoid (CVS) valve draws fresh air into the system through a vent.
Page 1 of 9 Document ID: 2792052 #02-06-04-037J: Check Engine Light On, Fuel Tank Hard to Fill, DTCs P0442, P0446, P0455 or P0449 Set (Replace Evaporative Emission (EVAP) Vent Valve Sloenoid Assembly and
More informationChevrolet Pickup Evaporator Kit (754563)
an ISO 9001:2008 Registered Company 1954-55 Chevrolet Pickup Evaporator Kit (754563) 18865 Goll St. San Antonio, TX 78266 Phone: 210-654-7171 Fax: 210-654-3113 www.vintageair.com 905459 REV B 10/05/15,
More information