The Refrigeration Cycle
|
|
|
- Daniel Wilkins
- 5 years ago
- Views:
Transcription
1 Job Sheet 4 The Refrigeration Cycle OBJECTIVES In this job sheet, you will plot the refrigeration cycle on a pressure-enthalpy diagram using pressures and temperatures measured on your training system. You will also calculate the coefficient of performance (COP) of your refrigeration system in heating mode. PROCEDURE In the following steps, you will take the different temperature and pressure readings necessary to trace the compression cycle on a pressure-enthalpy diagram. In heating mode, you will measure the temperature at the inlet and outlet of the compressor, the temperature at the outlet of the forced-air evaporator, and the pressure on both sides of the compressor. 1. Perform the following settings on your training system: Main power switch... Off Thermostat... Heating mode Temperature set point... 5 C (9 F) above room temperature Valve HV-1... Open Valve HV-2... Open Valve HV-3... Open Valve HV-4... Open Valve HV-5... Open Valve HV-6... Open Valve HV-7... Open Valve HV-8... Closed Valve HV-9... No adjustments required Valve HV Handle in horizontal position Valve HV Open Valve HV Open Valve HV Open Pressure gauge PI-1 selector switch... Right Pressure gauge PI-2 selector switch... Right Desuperheater On/Off switch... Off Priming tank three-way valves... Air distribution register... Open Festo Didactic
2 2. Use the next figure to compare the refrigeration cycle with the heat pump diagram and determine which thermocouples are going to be read during this exercise. Figure 69. Compression cycle. 3. Set the main power switch to On. 98 Festo Didactic
3 4. Measure the temperatures and pressures every four minutes after the compressor indicator light turns on. Complete Table 14. Table 14. Compression cycle. Time (min) Compressor inlet ( ) Temperature Compressor outlet ( ) Evaporator outlet ( ) Pressure LP HP 5. Set the thermostat operating mode to Off. 6. Using Figure 70, plot a graph showing TC-8, TC-9, and TC-11 temperatures as a function of time. Temperature Time (min) Figure 70. Temperature at various locations as a function of time in heating mode. Festo Didactic
4 7. Using Figure 71, plot a graph showing LP and HP pressures as a function of time. Pressure Time (min) Figure 71. Pressure as a function of time in heating mode. 8. Using your graphs as a reference, observe a pressure and temperature stabilization after a transitional period of about ten minutes. Using Table 14, copy your results taken after 16 minutes of operation into Table 15. Convert your pressure readings to absolute pressure values. a The standard atmospheric pressure at sea level is kpa (14.7 psia). Table 15. Temperature and pressure after 16 minutes of operation. Time (min) Compressor inlet ( ) Temperature Compressor outlet ( ) Evaporator outlet ( ) Pressure Gauge Absolute LP HP LP HP Using the values in Table 15, draw the refrigeration cycle on a pressureenthalpy diagram included at the end of this job sheet. Be sure to use the pressure-enthalpy diagram that corresponds to the system of units that you are using. 10. Identify the refrigerant conditions for points A to H shown in Figure 72. Label the points as subcooled, superheated, saturated liquid, saturated mixture, saturated vapor. Fill in the corresponding column in Table 16. Find the enthalpy value corresponding to the different refrigerant conditions identified in Figure 72 and complete Table Festo Didactic
5 Figure 72. Pressure-enthalpy diagram. Table 16. Refrigerant condition and enthalpy. Point Refrigerant condition Enthalpy A B C D E F G H 11. Using your results from Table 16, complete Table 17. Table 17. Refrigeration process. Process name Equation Refrigeration effect Low-pressure superheat Heat of compression High-pressure superheat Heat rejected by condenser Subcooling Expansion 12. Refrigeration devices are rated with a number called coefficient of performance (COP). The COP is the ratio of the refrigeration effect divided by the compression work. (4-2) Festo Didactic
6 Using the results from Equation (4-2), calculate the COP for your training system. COP of your training system in heating mode: 13. If you had to select a heat pump based solely on the COP, which one would you select? Would you select the heat pump with the lowest or highest COP? Why? 102 Festo Didactic
7 Job Sheet 4 The Refrigeration Cycle 14. Set the main power switch to Off. Figure 73. Pressure-enthalpy diagram, SI units. Festo Didactic
8 Job Sheet 4 The Refrigeration Cycle Figure 74. Pressure-enthalpy diagram, US customary units. Name: Date: Instructor's approval: 104 Festo Didactic
The Refrigeration Cycle
Job Sheet 4 The Refrigeration Cycle OBJECTIVES In this job sheet, you will plot the refrigeration cycle on a pressure-enthalpy diagram using pressures and temperatures measured on your training system.
Job Sheet 1. Geothermal Energy OBJECTIVES. Familiarization with the training system components PROCEDURE
Job Sheet 1 Geothermal Energy OBJECTIVES In this job sheet, you will become familiar with the training system components. You will operate your training system in heating and cooling mode and observe the
Pressure Enthalpy Charts
Pressure Enthalpy Charts What is a p-h Diagram? A p-h diagram is a diagram with a vertical axis of absolute pressure and a horizontal axis of specific enthalpy. "Enthalpy is the amount of energy in a substance
Thermodynamic Calculations of Two-Stage Vapor Compression Refrigeration Cycle with Flash Chamber and Separate Vapor Mixing Intercooler
Thermodynamic Calculations of Two-Stage Vapor Compression Refrigeration Cycle with Flash Chamber and Separate Vapor Mixing Intercooler Author: Volodymyr Voloshchuk Vl.volodya@gmail.com Introduction In
HVAC Fundamentals & Refrigeration Cycle
HVAC Fundamentals & Refrigeration Cycle Change of State of Water & the Refrigeration Cycle Change of State Water The Basic Refrigeration Cycle Types of DX Systems The Chilled water System The Cooling Tower
PRESSURE-ENTHALPY CHARTS AND THEIR USE By: Dr. Ralph C. Downing E.I. du Pont de Nemours & Co., Inc. Freon Products Division
INTRODUCTION PRESSURE-ENTHALPY CHARTS AND THEIR USE The refrigerant in a refrigeration system, regardless of type, is present in two different states. It is present as liquid and as vapor (or gas). During
REFRIGERATION CYCLE Principles of Mechanical Refrigeration Level 2: Cycle Analysis
REFRIGERATION CYCLE Principles of Mechanical Refrigeration Level 2: Cycle Analysis Technical Development Program Technical Development Programs (TDP) are modules of technical training on HVAC theory, system
Energy Use in Refrigeration Systems
2012 Rocky Mountain ASHRAE Technical Conference Energy Use in Refrigeration Systems PRESENTED BY: Scott Martin, PE, LEED AP BD+C Objectives Understand mechanical refrigeration terms Describe how heat is
AIR CONDITIONING. Carrier Corporation 2002 Cat. No
AIR CONDITIONING Carrier Corporation 2002 Cat. No. 020-016 1. This refresher course covers topics contained in the AIR CONDITIONING specialty section of the North American Technician Excellence (NATE)
Figure 1: Schematic of internal heat exchanger vapor-injection cycle
Vapor-injection technique Development Guideline 1. Introduction This guideline shows the advantage and characteristics of Mitsubishi vapor injected-scroll compressor. The vapor injected-scroll compressor
Section 1: Theory of Heat Unit 3: Refrigeration and Refrigerants
Section 1: Theory of Heat Unit 3: Refrigeration and Refrigerants Unit Objectives After studying this chapter, you should be able to: Discuss applications for high-, medium-, and low temperature refrigeration.
Paper No. : 04 Paper Title : Unit Operations in Food processing Module 11 : Principles of Refrigeration
Paper No. : 04 Paper Title : Unit Operations in Food processing Module 11 : Principles of Refrigeration 11.1 Introduction Preservation of foods is a vital processing step in food processing. There are
Case 15 Refrigeration System for Chemical Fertilizer Plant Ammonia Storage
Case 15 Refrigeration System for Chemical Fertilizer Plant Ammonia Storage Copy Right By: Thomas T.S. Wan ) Dec. 28, 2012 All Rights Reserved Case Background: Ammonia is one of the important elements to
Week 9. Refrigeration Cycles I. GENESYS Laboratory
Week 9. Refrigeration Cycles I Objectives 1. Introduce the concepts of refrigerators and heat pumps and the measure of their performance. 2. Analyze the ideal vapor-compression refrigeration cycle. 3.
MASS. MARITIME ACADEMY
MASS. MARITIME ACADEMY REFRIGERATION LAB OUTLINE Rev.3 Fall 2015 Table of Content Page Lab #1: Introduction to refrigeration system components, tools and procedures 1 Lab #2: Familiarization, operation,
AIM: TO STUDY THE PERFORMANCE OF THE DOMESTIC REFRIGERATION RIG.
AIM: TO STUDY THE PERFORMANCE OF THE DOMESTIC REFRIGERATION RIG. Page1 CONTENT: 1. Product Description 2. Product Specifications 3. Operating Procedure 4. Observation Table 5. Calculations 6. Result Page2
CHAPTER 7 PERFORMANCE ANALYSIS OF VAPOUR COMPRESSION REFRIGERATION SYSTEM IN HYBRID REFRIGERATION SYSTEM
111 CHAPTER 7 PERFORMANCE ANALYSIS OF VAPOUR COMPRESSION REFRIGERATION SYSTEM IN HYBRID REFRIGERATION SYSTEM 7.1 INTRODUCTION Energy is the primary component to run any system in the world. According to
REFRIGERATION CYCLES
REFRIGERATION CYCLES Carnot Cycle We start discussing the well-known Carnot cycle in its refrigeration mode. Figure 1: Carnot Cycle In this cycle we define the coefficient of performance as follows: COP
Refrigeration and Air Conditioning
Refrigeration and Air Conditioning 1. Pick up the wrong statement. A refrigerant should have (a) Tow specific heat of liquid (b) high boiling point (c) high latent heat of vaporisation (d) higher critical
TEST REPORT #65. Compressor Calorimeter Test of Refrigerant L-41-2 (R-447A) in a R-410A Scroll Compressor
Air-Conditioning, Heating, and Refrigeration Institute (AHRI) Low-GWP Alternative Refrigerants Evaluation Program (Low-GWP AREP) TEST REPORT #65 Compressor Calorimeter Test of Refrigerant L-41-2 (R-447A)
USING THE P-T CARD AS A SERVICE TOOL
Service Application Manual SAM Chapter 620-115 Section 2 USING THE P-T CARD AS A SERVICE TOOL Reprinted with permission from Sporlan Division, Parker Hannifin Corporation INTRODUCTION Manufacturers of
Basic Principals of Air conditioning By Dr. Esam Mejbil Abed
REPUBLIC OF IRAQ Ministry of Higher Education & Scientific Research University of Babylon College of Engineering Mechanical Engineering Department Basic Principals of Air conditioning By Dr. Esam Mejbil
Thomas J Kelly. Fundamentals of Refrigeration. Sr. Engineering Instructor Carrier Corporation. August 20, Page number: 1.
Thomas J Kelly Sr. Engineering Instructor Carrier Corporation August 20, 2003 1 SESSION OBJECTIVES At the conclusion of this session you should be able to: 1. Describe the basics principles of refrigeration
A Comparison Between Refrigerants Used In Air Conditioning
A Comparison Between Refrigerants Used In Air Conditioning Derya Özkan, Özden Agra and Özlem Çetin University of Yildiz Technical University, Turkey Corresponding email: tumer@yildiz.edu.tr SUMMARY It
ME 410 MECHANICAL ENGINEERING SYSTEMS LABORATORY MASS & ENERGY BALANCES IN PSYCHROMETRIC PROCESSES EXPERIMENT 3
ME 410 MECHANICAL ENGINEERING SYSTEMS LABORATORY MASS & ENERGY BALANCES IN PSYCHROMETRIC PROCESSES EXPERIMENT 3 1. OBJECTIVE The objective of this experiment is to observe four basic psychrometric processes
SBS5311 HVACR II Experiment 2: Analysis of the Combined Rankine and Vapour Compression Cycle
Introduction SBS5311 HVACR II http://ibse.hk/sbs5311/ Experiment 2: Analysis of the Combined Rankine and Vapour Compression Cycle The Rankine cycle is an idealized thermodynamic cycle of a heat engine
Chapter 9. Refrigeration and Liquefaction
Chapter 9 Refrigeration and Liquefaction Refrigeration is best known for its use in the air conditioning of buildings and in the treatment, transportation, and preservation of foods and beverages. It also
Compendium DES July 2016, CARN
Compendium DES July 2016, CARN 1 Contents Contents... 2 1. Energy balance... 4 Using Energy Balance for analyzing energy systems... 4 Energy Balance definition... 4 Steady state, steady flow... 4 Methodology...
TEST REPORT #34. Compressor Calorimeter Test of Refrigerant DR-7 in a R-404A Scroll Compressor
Air-Conditioning, Heating, and Refrigeration Institute (AHRI) Low-GWP Alternative Refrigerants Evaluation Program (Low-GWP AREP) TEST REPORT #34 Compressor Calorimeter Test of Refrigerant DR-7 in a R-404A
Combination unit to support instruction in Thermodunamics, Fluid Mechanics, and Heat Transfer
Paper ID #6647 Combination unit to support instruction in Thermodunamics, Fluid Mechanics, and Heat Transfer Dr. Lin Lin, University of Southern Maine Dr. Lin joined Department of Engineering at University
FS 231: Final Exam (5-6-05) Part A (Closed Book): 60 points
Name: Start time: End time: FS 231: Final Exam (5-6-05) Part A (Closed Book): 60 points 1. What are the units of the following quantities? (10 points) a. Enthalpy of a refrigerant b. Dryness fraction of
HEAT PUMPS. Carrier Corporation GT72-01 Cat. No
HEAT PUMPS Carrier Corporation 2003 GT72-01 Cat. No. 020-018 1. This refresher course covers topics contained in the HEAT PUMPS specialty section of the North American Technician Excellence (NATE) certification
LECTURE-17. Multi-Stage Vapour Compression Refrigeration. 1. Introduction
Lecturer: -Dr. Esam Mejbil Abid Subject: Air Conditioning and Refrigeration Year: Fourth B.Sc. Babylon University College of Engineering Department of Mechanical Engineering LECTURE-17 Multi-Stage Vapour
HVAC/R Refrigerant Cycle Basics
HVAC/R Refrigerant Cycle Basics This is a basic overview of the refrigeration circuit and how it works. It isn t a COMPLETE description by any means, but it is designed to assist a new technician or HVAC/R
Shell-and-Tube Heat Exchanger (Four Passes) - Optional
Exercise 2-4 Shell-and-Tube Exchanger (Four Passes) - Optional EXERCISE OBJECTIVE When you have completed this exercise, you will be familiar with the design and particularities of the four-pass shell
MECHANICAL ENGINEERING THERMAL AND FLUID SYSTEMS STUDY PROBLEMS
MECHANICAL ENGINEERING THERMAL AND FLUID SYSTEMS STUDY PROBLEMS MASS BALANCES, PSYCHROMETRICS & HVAC 1 Copyright 2018. All rights reserved. How to use this book The exam specifications in effect since
Use this Construction/HVAC Glossary to answer the questions below.
www.garyklinka.com Page 1 of 21 Instructions: 1. Print these pages. 2. Circle the correct answers and transfer to the answer sheet on the second last page. 3. Page down to the last page for the verification
RS-70 is suitable as a direct replacement for R-22 in low, medium and high temperatures in a great number of applications:
TECHNICAL DATA SHEET Features and uses of is a non-azeotropic blend of HFC with zero Ozone Depletion Potential et low Global Warming Potential (GWP), formulated to meet the requirements of the F-Gas Regulation
Technical Bulletin (TB-0037)
Technical Bulletin (TB-0037) BITZER Software Guide Version 4, January 2015 DEFINITION OF TERMS Terms Found in the BITZER Software Condenser Capacity: The power needed to reject heat from the refrigerant
Recommendations to retrofit positive existing installations running with HFCs (R404A & R507) RETROFIT POSITIVE & MEDIUM REFRIGERATING SYSTEMS
COMMERCIAL REFRIGERATION RETROFIT POSITIVE & MEDIUM REFRIGERATING SYSTEMS www.tecumseh.com Recommendations to retrofit positive existing installations running with HFCs (R404A & R507) 1-HCFCs & HFCs Retrofit
Steam Power Cycles Part II
Steam Power Cycles Part II Regenerative Cycles - Open and Closed Feedwater Heaters One approach to increasing the efficiency of steam power cycle is by extracting some of the steam from various stages
ME 410 MECHA ICAL E GI EERI G SYSTEMS LABORATORY
ME 410 MECHA ICAL E GI EERI G SYSTEMS LABORATORY MASS & E ERGY BALA CES I PSYCHROMETRIC PROCESSES EXPERIME T 3 1. OBJECTIVE The object of this experiment is to observe four basic psychrometric processes
TEST REPORT #32. System Soft-Optimized Test of Refrigerant D2Y60 in Air Source Heat Pump
Air-Conditioning, Heating, and Refrigeration Institute (AHRI) Low-GWP Alternative Refrigerants Evaluation Program (Low-GWP AREP) TEST REPORT #32 System Soft-Optimized Test of Refrigerant D2Y60 in Air Source
Analysis of Vapour Compression Refrigeration System with Refrigerants R134a, R143a, R152a, R290 and R32
www.ijird.com June, 201 Vol Issue 6 ISSN 2278 0211 (Online) Analysis of Vapour Compression Refrigeration System with Refrigerants,,, and Ramesh P. Sah Assistant Professor, Department of Mechanical Engineering
Calhoon MEBA Engineering School. Study Guide for Proficiency Testing Refrigeration
Calhoon MEBA Engineering School Study Guide for Proficiency Testing Refrigeration 1. To prevent an injury when working with refrigerants, what safety precautions are necessary? 2. When halogens are in
Performance Rating of Commercial and Industrial Unitary Air-Conditioning Condensing Units
ANSI/AHRI Standard 366 (SI) 2009 Standard for Performance Rating of Commercial and Industrial Unitary Air-Conditioning Condensing Units Approved by ANSI on 4 January 2011 IMPORTANT SAFETY DISCLAIMER AHRI
Refrigeration Training System
3401-20 Refrigeration Training System LabVolt Series Datasheet Festo Didactic en 120 V - 60 Hz 04/2018 Table of Contents General Description 2 Topic Coverage 2 Features & Benefits 2 List of Manuals 3 Table
Refrigerant Glide and Effect on Performances Declaration
Refrigerant Glide and Effect on Performances Declaration Scope and Purpose As a consequence of the EU regulation 517/2014 (F-gas), the future synthetic refrigerants with a low global warming potential
(Refer Slide Time: 00:00:40 min)
Refrigeration and Air Conditioning Prof. M. Ramgopal Department of Mechanical Engineering Indian Institute of Technology, Kharagpur Lecture No. # 10 Vapour Compression Refrigeration Systems (Refer Slide
ME Mechanical Engineering Systems Laboratory. Experiment 3 - Mass and Energy Balances in Psychrometric Processes
ME 410 - Mechanical Engineering Systems Laboratory Experiment 3 - Mass and Energy Balances in Psychrometric Processes Assist.Prof.Dr. Özgür BAYER, A-123 AIR-CONDITIONING (A/C) Goal: Control temperature
s. Properties for R134a are as follows : Saturated R-134a Superheated R-134a
CHAPTER 9 REFRIGERATION & AIR-CONDITIONING YEAR 2012 ONE MARK Common Data For Q. 1 and Q.2 A refrigerator operates between 120 kpa and 800 kpa in an ideal vapour compression cycle with R-134a as the refrigerant.
SECTION 2 SAFETY, TOOLS AND EQUIPMENT, SHOP PRACTICES UNIT 10 SYSTEM CHARGING
SECTION 2 SAFETY, TOOLS AND EQUIPMENT, SHOP PRACTICES UNIT 10 SYSTEM CHARGING UNIT OBJECTIVES After studying this unit, the reader should be able to Describe how refrigerant is charged into systems in
Air Conditioning Clinic. Absorption Water Chillers One of the Equipment Series TRG-TRC011-EN
Air Conditioning Clinic Absorption Water Chillers One of the Equipment Series TRG-TRC011-EN Absorption Water Chillers One of the Equipment Series A publication of The Trane Company Worldwide Applied Systems
Modeling and Testing of an R-23/R-134a Mixed Refrigerant System for Low Temperature Refrigeration
Marquette University e-publications@marquette Mechanical Engineering Faculty Research and Publications Mechanical Engineering, Department of 1-1-2013 Modeling and Testing of an R-23/R-134a Mixed Refrigerant
Due to its low temperature glide about 1.5 approx. (75% less than R-407C and R-427A), it is suitable for a wide range of applications.
TECHNICAL DATA SHEET R434A () Features and uses of R-434A () is a non-flammable HFC mixture. ODP = 0, compatible with traditional mineral lubricants, alkyl benzene and also with synthetic POE, so there
DEPARTMENT OF MECHANICAL ENGINEERING REFRIGERATION & AIR CONDITIONING LAB TRIPLE FLUID VAPOR ABSORPTION SYSTEM
DEPARTMENT OF MECHANICAL ENGINEERING REFRIGERATION & AIR CONDITIONING LAB TRIPLE FLUID VAPOR ABSORPTION SYSTEM Aim: To find COP of Triple Fluid Vapor Absorption System (TF_VAS) for 1 ohm and 2 ohm heat
"COP Enhancement Of Domestic Refrigerator By Sub cooling And Superheating Using Shell &Tube Type Heat Exchanger"
"COP Enhancement Of Domestic Refrigerator By Sub cooling And Superheating Using Shell &Tube Type Heat Exchanger" 1 Prof.Gaffar G.Momin, 2 Sagar B. Tupe, 2 Swapnil A. Parate 2 Omkar G. Yewale 2 Aakash P.
Institute of Aeronautical Engineering (Autonomous) Dundigal, Hyderabad B.Tech (III II SEM) MECHANICAL ENGINEERING
Institute of Aeronautical Engineering (Autonomous) Dundigal, Hyderabad- 500 043 B.Tech (III II SEM) MECHANICAL ENGINEERING REFRIGERATION AND AIR CONDITIONING Prepared by, Dr. CH V K N S N Moorthy, Professor
How Ground Source Heat Pumps Work
How Ground Source Heat Pumps Work How Ground Source Heat Pumps Work A heat pump is a mechanically simple system that is conceptually difficult to relate to. The boiler plate answer for how geo works is...
CHAPTER 3 BASIC STEAM CYCLE
CHAPTER 3 BASIC STEAM CYCLE To understand steam generation, you must know what happens to the steam after it leaves the boiler. A good way to learn the steam plant on your ship is to trace the path of
Effects of Flash and Vapor Injection on the Air-to- Air Heat Pump System
Purdue University Purdue e-pubs International Refrigeration and Air Conditioning Conference School of Mechanical Engineering 2010 Effects of Flash and Vapor Injection on the Air-to- Air Heat Pump System
Refrigerator/Heat pump
UMEÅ UNIVERSITY 2013-12-16 Department of Physics Leif Hassmyr Updates versions Joakim Ekspong 2017-10-31 Refrigerator/Heat pump 1 Task 1. Understand the principle of a refrigerator/heat pump and know its
Modeling And Testing Of R23/R134a Mixed Refrigerant System With Water Cooled Separator For Low Temperature Refrigeration
Marquette University e-publications@marquette Master's Theses (2009 -) Dissertations, Theses, and Professional Projects Modeling And Testing Of R23/R134a Mixed Refrigerant System With Water Cooled Separator
Refrigerants and lubricants
Refrigerants and lubricants GENERAL INFORMATION When choosing a refrigerant, different aspects must be taken into consideration: Legislation (now and in the future) Safety Application envelope in relation
Mechanical Heat Pump R515
P.A.Hilton Ltd Mechanical Heat Pump R515 Above: R515 shown fitted with standard wattmeter Stabilises in minutes allowing many tests to be conducted in a typical laboratory period. Allows a complete refrigerant
THE FIVE W s SYSTEMES LMP MECHANICAL SUB-COOLING. I.G.A. GIRARD, TERREBONNE, Qc. INCREASED SYSTEM EFFICIENCY & LOWER ENERGY COSTS
THE FIVE W s WHO: WHAT: WHERE: WHY: SYSTEMES LMP MECHANICAL SUB-COOLING I.G.A. GIRARD, TERREBONNE, Qc. INCREASED SYSTEM EFFICIENCY & LOWER ENERGY COSTS WHEN: TIME LAPSE May 2013 to May 2014 Système LMP`s
Installation Manual for. Series HWM and Non-ETI HYDRONIC WATER MODULE with SC and SD COMPRESSOR UNITS and R-410 REFRIGERANT
EarthLinked TXV Kit Installation Manual for Series HWM and Non-ETI HYDRONIC WATER MODULE with SC and SD COMPRESSOR UNITS and R-410 REFRIGERANT CONTENTS PAGE Pre-Installation 3 Hydronic Water Module Conversion
TEST REPORT #4. Travis Crawford Dutch Uselton. Lennox Industries Inc Metrocrest Drive Carrollton, TX 75006
Air-Conditioning, Heating, and Refrigeration Institute (AHRI) Low-GWP Alternative Refrigerants Evaluation Program (Low-GWP AREP) TEST REPORT #4 System Drop-in Test of Refrigerant R-32 in Split System Heat
Application Engineering
Revised September, 2006 ECONOMIZED VAPOR INJECTION (EVI) COMPRESSORS INDEX SECTION PAGE 1. Introduction... 1 2. Theory of Operation... 1 3. Nomenclature... 3 4. ARI Low Temperature Ratings... 3 5. Approved
REFRIGERATION CYCLES
REFRIGERATION CYCLES Carnot Cycle We start discussing the well-known Carnot cycle in its refrigeration mode. Figure 1: Carnot Cycle In this cycle we define the coefficient of performance as follows: COP
King Fahd University of Petroleum and Minerals Department of Mechanical Engineering. ME 431: Refrigeration. Laboratory Manual
King Fahd University of Petroleum and Minerals Department of Mechanical Engineering ME 431: Refrigeration Laboratory Manual February 2001 2 Table of Contents Contents Page # Safety Regulations 3 Lab Regulations
Performance Enhancement of Mini Refrigerator with Phase Change Materials
Performance Enhancement of Mini Refrigerator with Phase Change Materials Souptik Acharya 1, Manu Jose 2 and Risikesh Choudhury 3 Souptik Achraya,student at St. Martin s Engineering College Manu Jose T,
TEST REPORT #47. System Drop-in Test of R-32 and Refrigerant Blends ARM-71a, HPR2A, L-41-2 and DR-5A in a Five-Ton R-410A Rooftop Packaged Unit
Air-Conditioning, Heating, and Refrigeration Institute (AHRI) Low-GWP Alternative Refrigerants Evaluation Program (Low-GWP AREP) TEST REPORT #47 System Drop-in Test of R-32 and Refrigerant Blends ARM-71a,
Refrigerator and Heat Pump Objectives
10 CHAPTER Refrigeration Cycles 10-1 Refrigerator and Heat Pump Objectives The objective of a refrigerator is to remove heat (Q L ) from the cold medium; the objective of a heat pump is to supply heat
Oxyvap Evaporative Cooling Applications
Oxyvap Evaporative Cooling Applications Oxycom Fresh Air BV March 9th, 2015 Abstract This paper shows two highly efficient applications of the Oxyvap direct evaporative cooling technology, developed by
RSES Technical Institute Training Manual 3 72 hours, 72 NATE CEHs, 7.2 CEUs
Lesson 1 - Basic Heat Pump Theory (Part 1) Describe the basic operation of a heat pump. Explain the function of various heat pump controls. Interpret the wiring diagrams and performance data provided by
Installation Manual for ETI AVS Series and NON-ETI Air Handlers with SC or SD Compressor Units and R-410A Refrigerant
EarthLinked TXV Kit Installation Manual for ETI AVS Series and NON-ETI Air Handlers with SC or SD Compressor Units and R-410A Refrigerant CONTENTS PAGE Pre-Installation 3 Air Handler Conversion 4 System
1 /35 2 /35 3 /30 Total /100
Test is open book and notes. Answer all questions and sign honor code statement: I have neither given nor received unauthorized assistance during this exam. Signed Remember to show your work partial credit
ISSN Vol.08,Issue.21, November-2016, Pages:
ISSN 2348 2370 Vol.08,Issue.21, November-2016, Pages:4164-4170 www.ijatir.org Thermal Analysis of Vapour Compression Cycle for Different Refrigerants ALI MOHAMMED ABDOULHA MASSOUD 1, DR. MOHAMMAD TARIQ
Experiment 2: Test on Domestic Refrigerator for evaluation of EER.
Experiment 2: Test on Domestic Refrigerator for evaluation of EER. Specifications of Domestic Refrigerator: Model: Videocon refrigerator (single door) Capacity: 150 lit. Compressor: Hermetically Sealed
Mechanical Engineering Laboratory
Mechanical Engineering Laboratory MEE 416 Professor H. Ezzat Khalifa Syracuse University http://lcs.syr.edu/faculty/khalifa/mee416/ MEE416 1 A. Experiment 1 Air-Conditioning: Air-side Experiment 0031 Link
SIDDHARTH GROUP OF INSTITUTIONS :: PUTTUR Siddharth Nagar, Narayanavanam Road AUTONOMOUS QUESTION BANK (DESCRIPTIVE) UNIT I
SIDDHARTH GROUP OF INSTITUTIONS :: PUTTUR Siddharth Nagar, Narayanavanam Road 517583 AUTONOMOUS QUESTION BANK (DESCRIPTIVE) Subject with Code : Refrigeration and Air Conditioning (16ME8806) Course & Branch:
Otherwise, you can continue reading the file on the following pages.
If you d like to be able to print this file out to study off-line or use on the job, a printable version is available for an administrative fee of $3.97 USD. To download the unlocked file, click here.
Evaluation of HCFC Alternative Refrigerants
Evaluation of HCFC Alternative Refrigerants Shaobo Jia Global Innovation Heatcraft Worldwide Refrigeration shaobo.jia@heatcraftrpd.com Introduction It is well-known that HCFC refrigerants widely used in
Challenges in Designing Low-Cost Media-Isolated MEMS Pressure Transducers for HVAC/R Applications
Challenges in Designing Low-Cost Media-Isolated MEMS Pressure Transducers for HVAC/R Applications Tom Kwa, PhD CTO DunAn Sensing LLC 10 June 2015 Long Beach, California Outline The need for HVAC/R HVAC/R
Single Screw Ammonia Heat Pumps. Harness Your Heat... Don t Reject It
Single Screw Ammonia Heat Pumps Harness Your Heat... Don t Reject It Harness Your Heat Don't Reject It Industrial processes consume considerable energy from two primary sources in the production of their
Performance analysis of a vapour compression refrigeration system with a diffuser for theeco-friendly refrigerants R-134a, R-600a and R-152a
International Journal of Research in Engineering and Science (IJRES) ISSN (Online): 2320-9364, ISSN (Print): 2320-9356 Volume 4 Issue 6 ǁ June. 2016 ǁ PP. 52-57 Performance analysis of a vapour compression
Fig.: macroscopic kinetic energy is an organized form of energy and is much more useful
Harnessing Energy Fig.: macroscopic kinetic energy is an organized form of energy and is much more useful Vapor Power Cycle The vast majority of electrical generating plants are variations of vapor power
Performance Characteristics of Air-Conditioner Under Tropical Ambient Condition
Purdue University Purdue e-pubs nternational Refrigeration and Air Conditioning Conference School of Mechanical Engineering 2 Performance Characteristics of Air-Conditioner Under Tropical Ambient Condition
Geothermal Training System
46126-00 Geothermal Training System LabVolt Series Datasheet Festo Didactic en 120 V - 60 Hz 05/2018 Table of Contents General Description 2 Geothermal Heat Pump 3 Ground-Loop Heat Exchanger 4 Domestic
THEORETICAL INVESTIGATION OF THE PERFORMANCE OF SOME ENVIRONMENT-FRIENDLY REFRIGERANTS IN A SUB-COOLING HEAT EXCHANGER REFRIGERATION SYSTEM
Journal of Science and Technology, Vol. 30, No. 3 (2010), pp 101 2010 Kwame Nkrumah University of Science and Technology (KNUST) THEORETICAL INVESTIGATION OF THE PERFORMANCE OF SOME ENVIRONMENT-FRIENDLY
B. A. T. Basic Appliance Training
B. A. T. Basic Appliance Training BASIC REFRIGERATION presented by Phil Whitehead Program Objective The objective of this program is to give you some of the basic elements that are essential to understanding
Geothermal Training System (46126-A0)
Geothermal Training System 582385 (46126-A0) LabVolt Series Datasheet Festo Didactic en 220 V - 60 Hz 03/2019 Table of Contents General Description 2 Geothermal Heat Pump 3 Ground-Loop Heat Exchanger 4
Chapter 11. Refrigeration Cycles. Study Guide in PowerPoint
Chapter 11 Refrigeration Cycles Study Guide in PowerPoint to accompany Thermodynamics: An Engineering Approach, 7th edition by Yunus A. Çengel and Michael A. Boles The vapor compression refrigeration cycle
Technical Information
Date of last update: May-15 Ref: C7.19.2/0813-0515/E Application Engineering Europe ZF* REFRIGERATION COPELAND SCROLL COMPRESSORS USING R407A, R407F, R448A OR R449A IN LOW TEMPERATURE APPLICATIONS ZF*
Week 13 Chapter 10 Vapor & Combined Power Cycles
MECH341: Thermodynamics of Engineering System Week 13 Chapter 10 Vapor & Combined Power Cycles The Carnot vapor cycle The Carnot cycle is the most efficient cycle operating between two specified temperature
Water Jet Nozzle to reduce the operation cost in Air Conditioning unit
Water Jet Nozzle to reduce the operation cost in Air Conditioning unit By The Group of Energy Conservation Team of The Faculty of Technology Industry of Mechanical Engineering Department of the University
A Treatise on Liquid Subcooling
A Treatise on Liquid Subcooling While the subject of this article is Liquid Refrigerant Subcooling, its affect on the operation of the thermostatic expansion valve (TEV), and ultimately on system performance
PLEASE READ AND FOLLOW THESE INSTRUCTIONS
ME 300 Final Examination May 2, 2005 161 ME or 261 ME Name: Thermo No. Section: (Please circle) 8:30 a.m. 11:30 a.m. 2:30 p.m. PLEASE READ AND FOLLOW THESE INSTRUCTIONS 1. Put your name on each page of
Refrigeration/Troubleshooting Manual
Refrigeration/Troubleshooting Manual P.O. Box 245 Syracuse, NY 13211 www.roth-america.com 888-266-7684 P/N: 2300100910 Table of Contents: Section 1: Geothermal Refrigeration Circuits Overview... 2 Water-to-Air