The sealless FLUX F 424

Transcription

1 The sealless FLUX F The liquids to be pumped are abrasive, but they do not leave any deposits. Dry running of the pump must not cause any problems. You are looking for a lightweight, general purpose pump in stainless steel, polypropylene or polyvinylendene fluoride. The inner tube supports the pump shaft, which is lubricated by the liquid. The level of the liquid in the inner tube always corresponds to that in the drum or container. Special advantages: Safe dry running of the pump No wearing of seals The liquid being pumped is not contaminated by the shaft lubricant Inner tube and helix shaped support bearings completely self-draining Flexible coupling between motor and pump O-ring to seal between inner and outer tube (not in the liquid section) Radial shaft seals to prevent liquid and/or vapours entering the coupling area Non-metallic helix shaped shaft support bearing Here a FLUX pump in sealless version is your pump. Pressure relief ports Type F Bottom bearing assembly which centers the shaft within the inner tube Impeller in ETFE Explosion-proof versions available

2 FLUX drum pumps in stainless steel FLUX drum pumps in stainless steel 6 Ti except sanitary pump F 7 S are approved according to ATEX-Directive //EC for use in Zone 0, temperature class T, for transferring highly flammable liquids out of portable drums or containers. With the help of the performance charts you can compare the delivery rates achieved by each pump model powered by the various FLUX motors. Detailed motor data are shown on pages to. FBM 000 Ex F 60 Ex F 60 Ex EL F 60- Ex When using the pump with a discharge hose (of approx. 6, ft) and a quick action tap, the delivery rate will be approx. GPM. Depending on the motor type a GAL drum can be emptied within minutes. The delivery rates shown in the performance charts are obtained at the outlet connection of the pump. Special version for horizontal use on request. FP Ex S-/ with zone separation F 6 Ex F F EL F - F 7 F 7 EL F 6- Ex F FEM 070 This pump version will achieve a higher delivery rate! This pump version will achieve a higher delivery head! Max. viscosity per pump and motor, please see pages and. motor FBM 000 Ex motor F 6 Ex, F 6- Ex or F 6- Ex motor FEM 070 H [mws] H [ft] Detailed motor data see pages to

3 drum pump (tube set) in stainless steel, thread on outlet G ¼ male, motors on page type/curve FP Ex S-/ ( FP Ex S-/7 Z ( FP Ex S-0/ Z ( version seal type material sealless within the liquid section shaft in stainless steel 6 Ti, impeller in ETFE, o-ring in FKM max. temperature F outer-ø 6 6 part no. / weight immersion length /, Ibs 07 /, Ibs 07 / 6,6 Ibs immersion length 00 / 6, Ibs 0 / 6, Ibs 0 /, Ibs immersion length 7 0 / 7,7 Ibs / 7,7 Ibs / 0,6 Ibs type/curve FP Ex S-/ (, F 6 S-/ F 7 S-/ version, % drum emptying mixing pump sanitary pump seal type mechanical seal in ceramic oxide, PTFE/carbon, o-rings in FKM sealless within the liquid section material shaft in stainless steel 6 Ti, seal in FKM, impeller in ETFE shaft in stainless steel 6 Ti, impeller in ETFE, o-ring in FKM max. temperature F outer-ø 6 part no. / weight immersion length 7 00 / 6,6 Ibs / 6,6 Ibs immersion length 0 /,7 Ibs /,7 Ibs / 6, Ibs immersion length 7 0 /,70 Ibs /,70 Ibs 7 0 / 7,7 Ibs type/curve F 0 S-/ ( F 0 S-/7 Z ( F 0 S-0/ Z version seal type material mechanical seal in ceramic oxide, PTFE/carbon, o-rings in FKM shaft in stainless steel 6 Ti, seal in FKM, impeller in ETFE max. temperature F outer-ø part no. / weight immersion length /, Ibs /, Ibs / 7, Ibs immersion length / 6,6 Ibs / 6,6 Ibs /, Ibs immersion length / 7, Ibs 0 0 / 7, Ibs 0 0 /,6 Ibs accessories hose connection complete with nut G ¼ female DN part no DN part no. 0 0 Pump models in immersion lengths of (in steps of ) on request motor F 7 or F 7 EL motor F, F EL, F 60 Ex or F 60 Ex EL Model for higher delivery head on request. motor F - or F 60- Ex with zone separation Values ± 0% with water (6 F) and a voltage of 0 Volt. Curves with a voltage of 0 Volt / 60 Hz are similar.

4

5

6 general view FLUX drum and container pump with accessories for highly flammable liquids (explosion-proof version) It is not merely the pump that makes the FLUX solution a perfect equipment. On this page you will find a general view on the explosion-proof FLUX drum pump together with all accessories for transferring highly flammable liquids. With all items in bold printing you will have a ready to use pump assembly, which may be completed by other accessories shown on this page drive motor drum pump (pump tube set) FLUX-clip suction strainer compression gland 0 6 fume gland type FES 7 flexible hose* 6 swaged hose fittings* 7 discharge spout liquid meter connecting piece FMC 00 carrying handle earth (ground) wire explosion-proof plug explosion-proof socket wall bracket quick action tap * On request also available completely mounted and tested for electrical conductivity. 0

7 general view FLUX drum and container pump with accessories for non-flammable liquids It is not merely the pump that makes the FLUX solution a perfect equipment. On this page you will find a general view on the FLUX drum pump together with all accessories for transferring non-flammable liquids. With all items in bold printing you will have a ready to use pump assembly, which may be completed by other accessories shown on this page drive motor drum pump (pump tube set) FLUX-clip suction strainer compression gland fume gland type FES 0 7 hose connection flexible hose* 6 hose clip quick action tap discharge spout liquid meter carrying handle quick action coupling type SSK 00 attachment clamp wall bracket