CENTRIFLOW 3D. >> Installation and Maintenance. air comfort. CentriFlow 3D

Transcription

1 CENTRIFLOW 3D Plug fan GMEC >> Installation and Maintenance air comfort CentriFlow 3D

2 2 Plug Fan CentriFlow 3D GMEC Installation and Maintenance Important Information, Safety notes, Technical Description 1. Important Information Fläkt Woods fans comply with the requirements for health and safety of the EC Machinery Directive. All fans leave the factory after being subjected to testing. These instructions are intended for use by professional service staff. The installation, commissioning and operation of the fans must be carried out by professional staff who are familiar with the safety regulations. Tools and protective equipment necessary for preventing accidents from occurring while installing and operating the fan must be used/worn in accordance with the local safety regulations. All personnel involved with the product must carefully study this operating manual and diligently comply with all orders and instructions. Fläkt Woods does not accept responsibility for any damage that can be attributed to non-observance of these instructions. The warranty issued by the manufacturer will be forfeited if any changes to the product are made without the manufacturer s consent. 2. Safety Notes This symbol is designed to point out all safety and danger related information regarding danger on the operating personnel s lives and health. 3.2 Operating conditions The standard operating temperature range of the fan is 20 C C. The maximum permissible ambient temperature of the motors is +40 C. The fans are designed to be used as parts of equipment. They are not ready for use as a stand-alone product and the standard version does not have protection against body contact, the appropriate protective measures are to be taken according to EN 292/294. Only operate the fan up to the maximum permissible speed given in the information on the fan rating plate. 3.3 Motors Centriflow 3D GMEC fans are supplied with high efficiency (IE4) permanent magnet external rotor EC-motors. The high efficiency is based on permanent magnets which eliminate rotor losses and therefore less magnetizing current is needed. Motors are equipped with integrated control electronics and speed can be controlled by using either 0-10 V control signal or input or the MODBUS-RTU interface for communication. The impeller is fastened directly to the motor. 3. Technical Description The fan is used to generate a desired air volume at a given pressure rise that corresponds to the pressure losses in the duct system to which the fan is connected, and internal losses inside of the Air Handling Unit. The plug fan is intended to be used inside of the Air Handling Unit. 3.1 Design Front plate 2. Inlet cone 3. Impeller 4. Motor 5. Support bracket 3

3 Installation and Maintenance 3 Plug Fan CentriFlow 3D GMEC Transport, Mounting Instructions 4 Transport 5 Mounting instructions 4.1 Transport inspection 5.1 Horizontal wall mounting from the outside of the fan casing - Fan sizes Check the fan immediately after you receive it and make sure that it has not been damaged during transport. If you discover any damage, get in touch with the transportation company without delay. Briefly rotate the fan impeller to see that it rotates easily. Check the information on the fan rating plate. Proper procedures must be followed when transporting the product! Faulty conditions in transporting may result in serious damage on the product Preparing the fan wall First make sure that the wall is rigid enough. There must be a square hole and mounting screws symmetrically on the corners of the hole. Verify that the dimensions are according to the dimension table below. Make sure that the screw length is at least 30 mm from the wall surface. W 1 W 4.2 Transport Safety The transport material is to be selected according to the packaging and the weight of the product. Loading must be carried out as instructed. 4.3 Intermediate Storage 2 0 h 3 ngt e l ew Scr 4xM 8 If the fan is to be stored before or in between uses, the following needs to be taken in account: Original packaging is to be used. If the storage conditions require it, additional protection may be added The storage environment must be dry, dust-free and not have a high level of humidity (<70%) Storage temperature must be in between 25 C and +40 C Before commissioning, the respective instructions must be studied thoroughly. Fan Size W2 ± W1 ±2 Screws Mounting Preparations Before mounting of the fan prepare sealing on the wall closely around the edges of the square hole. Sealing can be done by any workable method, such as sealant mass, sealing tape, rubber gasket etc. Sealing must be uniform all around. Make sure that the cable glands are pointing downwards and the air flow measurement tube is safely located i.e. not pressed between the front plate of the fan and the wall. Tighten the fan on the wall. Sealing M8 nuts Cables downwards Fläkt Woods 9941GB Specifications are subject to alteration without notice

4 4 Plug Fan CentriFlow 3D GMEC Installation and Maintenance Mounting Instructions 5.2 Horizontal wall mounting inside the fan casing - Fan sizes Preparing the fan wall First make sure that the wall is rigid enough. There must be a circular hole and mounting screws symmetrically around the hole. Verify that the dimensions are according to the dimension table below. Make sure that the screw length is at least 30 mm from the wall surface. Install sealing around the circular hole. Sealing height must be over 15 mm (25 mm in case of size 056) from the wall surface. 8 x M8 nuts Cable glands downwards M8 W 2 W 1 ØD 1 Screw length 30 Sealing; thickness >15mm (>25mm for fan size 056) Fan sizes Vertical mounting - Fan sizes Mounting preparations Preparing the mounting surface. First make sure that the surface is rigid enough. There must be a circular hole and mounting screws symmetrically around the hole. Verify that the dimensions are according to the dimension table below. Install sealing. Sealing height must over 15 mm (25 mm in case of size 056) from the surface. Sealing; thickness >15mm (>25mm for fan size 056) W 2 W 1 Fan Size ØD 1 ±3 W 1 ±3 W 2 ±2 Screws pcs. M pcs. M pcs. M pcs. M pcs. M pcs. M pcs. M pcs. M Mounting of the fan Before mounting make sure that the cable glands are pointing downwards and the air flow measurement tube is safely located i.e. not pressed between the front plate of the fan and the wall. Tighten the fan on the wall. ØD 1 Fan Size ØD 1 ±3 W 1 ±3 W 2 ±2 Screws pcs. M pcs. M pcs. M pcs. M pcs. M pcs. M pcs. M pcs. M Mounting of the fan Before mounting make sure that the air flow measurement tube is safely located i.e. not pressed between the front plate of the fan and the mounting surface. Tighten the fan on the place. M8 4 x M8 nuts M8 Cables downwards Fan sizes

5 Installation and Maintenance Plug Fan CentriFlow 3D GMEC 5 Mounting Instructions, Commissioning, Maintenance 5.4 Grounding Motor is grounded through the motor power supply cable. If extra grounding is needed, grounding can be done with a separate cable from the fan motor to the casing of the Air Handling Unit. The motor has a grounding marking next to the grounding point (View A). 7. Maintenance 7.1 Warranty A precondition of the warranty is that regular maintenance has been carried out. Defects under warranty must immediately be notified to the manufacturer or the importer. The warranty does not cover service work or indirect damages. A A 7.2 Maintenance BEFORE MAINTENANCE Switch off the power supply to the fan at the safety switch and wait until the impeller is fully stopped. Extra grounding cable Inspection The fan is to be inspected at least once a year. 5.5 Fitting the accessories The inlet protective screen can be fitted directly to the front plate of the fan or outside Air Handling Unit to the inlet opening. 5.6 Electrical connections All electrical connections must be wired by authorized personnel only. The necessary electrical and safety precautions must be taken into account. Connections must be done according to the instructions, see separate Controls Instructions for GMEC. 6. Commissioning 6.1 Safety checking - Check that the impeller rotates freely. Make sure that there are no foreign objects in the fan or in the Air Handling Unit. Also check that there is no unusual noise in the fan or motor. Check that the installation work has been carried out in accordance with the relevant regulations. Cables and air flow measurement tubes must be attached so that they do not touch the impeller All necessary protective devices must be installed. The fan may only be commissioned after all proper procedures have been followed and all necessary inspections have been carried out Checking the Motor Inspect that there are no visible damages on the fan or the motor Impeller The impeller can be cleaned by using a vacuum cleaner, compressed air or by brushing. If the impeller is coated with greasy dirt it can be washed with a detergent or a solvent. The cleaning is to be done at least once a year. Badly tarnished impeller will result in lower efficiency of the fan and increases energy consumption. The maximum permissible vibration levels are: Vibration level Alarm Shutdown BV-2 (below 3.7 kw) BV-3 (over 3.7 kw) 11,8 12,5 Values are RMS-values in mm/s measured on the motor. 7.3 REPLACING THE fan Replace the fan unit in case of failure. The impeller and the motor cannot be changed. The fan has to be disconnected before removing. 6.2 Test run Briefly switch on the power supply to the motor to check whether the fan impeller rotates in the correct direction. If the impeller is rotating in the correct direction, the fan may be switched on. Check that no abnormal mechanical sound and no surging occur.

6 6 Plug Fan CentriFlow 3D GMEC Installation and Maintenance faults, spare parts, distances, Air flow measurement device, disposal 8. FAULTS If any faults occur during operation, they shall be repaired by qualified maintenance personnel. Some examples of incorrect use: - foreign particles inside fan (AHU) - corrosive media inside AHU - too low or high temperatures - too high vibrations - incorrect maintenance Possible problems generated: - bearing damage - corrosion damage - vibration generated damage - broken impeller 9. SPARE PARTS A complete fan is available as a spare part. No separate parts are available. For more information please contact Fläkt Woods sales unit. 11. Air flow measurement device The airflow sensor is used for measuring the airflow of the plug fans. The method is based on differential pressure. The pressure is measured at a specific point in the inlet cone and the reference pressure is measured upstream of the inlet cone. The air flow sensor is supplied factory mounted in the inlet cone. The air flow is calculated as a function of the coefficient k and the differential manometer reading Dp m from the equation: q v = 1 k q v = air flow m 3 /s k = k-factor of each fan Dp m = differential pressure reading (Pa) x p m 10. RECOMMENDED DISTANCE TO OTHER COMPONENTS To achieve the best possible operation of the fan inside of the Air Handling Unit the following minimum distances shall be followed: LD C R ØD E Size C Ø D E LD R A x B GMEC-3-aaa k-factor DISPOSAL OF THE PRODUCT Used product shall be disposed or recycled according to the local laws and regulations.

7 Installation and Maintenance Plug Fan CentriFlow 3D GMEC Declaration of conformity EC Declaration of incorporation for Partly Completed machinery Machinery Directive 2006/42/EC, Annex II, sub B Manufacturer: Fläkt Woods Oy Address: Kalevantie 39 FI Turku, Finland Name and address of the person authorised to compile the relevant technical documentation: Name: Heikki Stenberg Address: as above The design of the Partly Completed Machinery: GMEB/GMPM /GMEC with accessories Induction AC-motor Induction AC-motor with integrated VSD Electronically commutated external rotor motor with integrated controller Permanent magnet motor with controller The following essential requirements of the Machinery Directive (2006/42/EC) are applied and fulfilled: 1.1.2, 1.1.3, 1.1.5, The specific technical documentation in accordance with Appendix VII B has been written and is available. The specific documentation will be transmitted to a reasoned request by national authorities. And that this partly completed machinery is in conformity with the provisions of the following other EC- Directives: Low Voltage Directive 2014/35/EU EMC-Directive 2014/30/EU ErP Directive 2009/125/EC And furthermore, declares that the following (parts/clauses of) European harmonised standards have been applied: EN ISO , EN ISO 13857:2008 and ISO EN 5801 This partly completed machinery must not be put into service until the final machinery into which it is to be incorporated has been declared in conformity with provisions of the Machinery Directive 2006/42/EC, where appropriate. Turku, Heikki Stenberg R&D Manager

8 FWG-Plug Fan-GMEC-Installation and Manitenance-GB GB Copyright 2017 Fläkt Woods Group Centriflow Plus 9941GB A history of innovation and reliability Fläkt Woods is a global leader in air management. We specialize in the design and manufacturing of a wide range of air climate and air movement solutions. Our product brands such as SEMCO, eq, eq PRIME, Econet, Veloduct, Optivent, Econovent and Cleanvent are well-known and trusted by customers all over the world to deliver Air Comfort and Fire Safety. We are constantly aiming to provide systems that precisely deliver required function and performance, as well as maximum energy efficiency. Manufacturer: Fläkt Woods Oy Kalevantie 39, FI Turku, Finland Phone info@flaktwoods.com