Service Bulletin Trucks Date Number Page

Size: px
Start display at page:

Download "Service Bulletin Trucks Date Number Page"

Transcription

1 Mack Trucks, Inc. Allentown, PA USA (Does not apply to Mack Trucks Australia) (Supersedes SB dated 03/27/07) Service Bulletin Trucks Date Number Page 11/04/08 SB (25) Cooling System Revisions SB215025, Cooling System Revisions ASET AC (November 2008) To improve water pump seal life, and to reduce occurrences of coolant loss from the surge tank and cooling system surge noise/vibration (a noise and very rapid vibration of the upper radiator tube), a revised thermostat housing, water pump inlet tube, a new coolant static fill tube and a revised thermostat arrangement were implemented into production as follows: Revised Thermostat Housing April 12, 2004 Revised Water Pump Inlet Tube and Static Fill Tube January 12, 2005 Revised Thermostat Arrangement December 4, 2006 (beginning with engine serial No. 6X2772) Revised Thermostat Housing, Water Pump Inlet Tube and Static Fill Tube The thermostat housing consists of two sections (the thermostat section and bypass section), with a cast wall separating the two. In order for the bypass feature to function, there must be a passage through the cast wall to allow coolant flow between the two sections. Beginning April 12, 2004, a thermostat housing having a larger opening in the divider wall between the thermostat and bypass sections was phased into production. This change, which reduces the pressure differential between the thermostat section and the bypass section, provides improved water pump seal life and reduced cooling system noise and vibration. 1 Figure 1 Thermostat Housing Comparison 1. Current Thermostat Housing (Part No. 493GB521P2) 2. Larger Opening in Divider Wall 3. Drill Point Mark Denotes Part No. 4. Previous Thermostat Housing (Part No [A]) 5. Two 1/2 Openings in Divider Wall

2 Service Bulletin 11/04/08 SB (25) Previously, the coolant return lines for the cab heater, sleeper heater and fuel heater were connected to the thermostat housing. Less pressure differential inside the thermostat housing, however, results in insufficient coolant flow through the heaters. Because of this, return lines for the cab heater, sleeper heater and fuel heater are now connected to the static fill tube. The revised thermostat housing part No. 493GB521P2 includes the five tapped ports originally used for the coolant return lines. DO NOT use these ports for the cab and/or fuel heater coolant return lines, as adequate pressure differential does not exist and sufficient coolant flow will not be attained. The water pump inlet tube now includes a connection for the new static fill tube. The new static fill tube arrangement includes spuds for the cab heater and fuel heater coolant return line connections. 2 Figure 2 Water Pump Inlet Tube 1. Water Pump Inlet Tube (Part No. 670GC Connection for Static Fill Tube 3. Static Fill Tube (Part No. 227GC516) 4. Fuel Heater Return Connection 5. Cab Heater Return Connection 6. Sleeper Heater Return Connection Should pushing coolant (coolant loss from the surge tank) or cooling system surge noise/vibration be encountered, the cooling system should be revised as outlined in the following instructions.

3 Service Bulletin 11/04/08 SB (25) Some chassis may already have been modified with some of the revisions outlined in this bulletin. For example, some chassis may be equipped with a revised thermostat housing (part No. 493GB521 or 493GB521P2), but not the static fill tube. On these chassis, the cab, sleeper and fuel heater return lines may either be connected to the lower radiator tube or to the thermostat housing. The thermostat housing will not be replaced on these chassis, but the new water pump inlet tube and static fill tube will be required. Additionally, it will be necessary to reroute the heater return lines from either the thermostat housing or the lower radiator tube to the static fill tube. This service bulletin covers all arrangements. Thermostat Hosing and Thermostat Installation Before proceeding, determine if the thermostat housing must be replaced by looking at the part number located on the top of the housing (refer to Figure 1). For engines having thermostat housing part No. 493GB520(A), the existing thermostat housing must be replaced with the revised housing part No. 493GB521P2. If the engine is equipped with thermostat housing part No. 493GB521, DO NOT replace the housing, but proceed with installing the water pump inlet tube and installing the static fill tube. If equipped with 493GB521 thermostat housing, a plug (part No X16) will be required to close the static fill port in the side of the housing. Parts required for replacing the thermostat housing are as follows: 3 Figure 3 Thermostat Housing Assembly

4 Service Bulletin 11/04/08 SB (25) In addition to the parts listed above, the following parts will also be required (not shown in above exploded view): Procedures for removing and reinstalling the thermostat housing are as follows: 1. Disconnect the batteries by disconnecting the negative battery cable(s) first, and then the positive battery cable(s). 2. Open the hood. 3. Drain the coolant into a clean container. Cover the container to prevent dirt from contaminating the coolant. The same coolant will be reused to fill the system. 4. Remove the EGR mixer tube as follows: 4 Key Qty. Part No. Description SB169A Kit, thermostat (includes two vented with ball check thermostats, [one part No. 657GC324BP80 and one 657GC324BP85] and two seals (part No. 447GC216A) GC251 Shield, thermostat housing AX233 Plugs GB521P2 Housing, thermostat *All five ports must be plugged. Reuse plugs from existing housing. One or two additional plugs will be required. Qty. Part No. Description 1 446GC2149 O-ring, EGR mixer tube 1 449GC237M Wire mesh seal, EGR mass flow tube flange (required if mass flow tube has the bellowstype connection) Figure 4 EGR Mixer Tube 1. Pressure Sensor 2. Temperature Sensor Boost Pressure Relief Valve 4. EGR Cool Tube 5. Relief Valve Outlet Tube 6. Mixer Tube 7. Relief Valve Outlet Tube Clamp 8. Capscrews

5 Service Bulletin 11/04/08 SB (25) 5 a. Loosen the clamps at both coupling hoses on the inlet air duct between the charge air cooler outlet and the EGR mixer tube, and then remove the inlet air duct. b. Disconnect the harness connectors for both the outlet pressure and temperature sensors. c. Loosen the two clamps that secure the coupling hose to the boost pressure relief valve, and then remove the coupling hose. 6 Figure 5 Boost Pressure Relief Valve Coupling Hose d. Remove the capscrew from the support bracket at the side of the EGR mixer tube. The bracket is attached between the mixer tube and the coolant manifold. Figure 6 EGR Mixer Tube Support Bracket 1. Mixer Tube 2 Mixer TUbe EGR Mass Flow Tube Flange 3. Support Bracket 4. Coolant Manifold

6 Service Bulletin 11/04/08 SB (25) 7 e. Loosen and remove the clamp attaching the upper EGR mass flow tube to the mixer tube. If the mass flow tube uses the bellows-type connection, remove and discard the seal in the flange. Figure 7 Upper Gas Tube-to-Mixer Connection (Bellows-Type SHown) 1. EGR Mixer Tube 2. EGR Mass Flow Tube f. Remove the two capscrews securing the EGR mixer tube to the inlet manifold, and lift the mixer tube out of the way to gain access to the thermostat housing. 5. Disconnect the cab/sleeper heater and fuel heater (as equipped) return lines from the side of the thermostat housing. 6. Disconnect the bypass hose and the surge tank hose from the thermostat housing. 7. Remove and discard the coupling hose between the upper radiator tube and the thermostat housing. 8. Remove the thermostat housing from the water manifold. 9. Remove the 3/8Ð pipe plugs from the ports in the original thermostat housing and install them into the new housing (part No. 493GB521P2). Use thread sealant (either Teflon tape or pipe thread sealant) and tighten the plugs to 18 lb-ft (24 N m). 10. Place the new thermostat housing top side down (with the thermostat openings facing up) on a workbench, and then install a new shield (part No. 492GC251) with the flat side facing up (toward the installer), into each thermostat bore. An installation tool is not required. It is only necessary to use finger pressure to push the shields to their fully seated position on the bottom of the thermostat housing.

7 Service Bulletin 11/04/08 SB (25) 11. Install a new seal (part No. 447GC216A) into each of the thermostat bores. Install the seal with the metal portion facing up (toward the installer), and use seal installation tool No. J A to install the seals. The installation tool ensures that the seals are installed to the proper depth. The two seals (part No. 447GC216A) and thermostats (part No. 657GC324BP80 [180 ] and 657GC324BP85 [185 ]) are included in the thermostat kit (part No. 215SB169A). 8 Figure 8 Installing Thermostat Housing Shields and Seals 1. Thermostat Housing (Part No. 493GB521P2) 2. Shields (Part No. 492GC251), Flat Side Faces Up, Toward the Opening in the Housing. 3. Seal (Part No. 447GC216A), Metal Side Faces Up, Toward the Opening in the Housing

8 Service Bulletin 11/04/08 SB (25) 12. With the ball check valve facing forward, position the thermostats (one part No. 657GC324BP80 and one part No. 657GC324BP85) into the thermostat bores. For proper vent function, it is very important that the thermostat be installed with the ball check valve facing forward. The straps that retain the thermostat spring must face forward in the same direction as the vent port/ball check valve. If the straps are not facing the same direction, grasp the body of the thermostat and rotate the top portion until the straps are properly oriented. It does not matter into which bore the 180 and 185 thermostats are installed. 9 Figure 9 Thermostat Installation 1. Strap Must Face Same Direction as Vent Port/Ball Check Valve 2. Vent Port/Ball Check Valve Faces Front 13. Place the thermostat housing assembly on the water manifold mounting surface, then install the three mounting capscrews. Tighten the capscrews to 21 lb-ft (29 N m). 14. Reinstall the EGR mixer tube as follows: a. If the mass flow tube uses the bellows-type connection, install a new wire-mesh seal (part No. 449GGC237M) in the upper mass flow tube flange of the mixer tube.

9 Service Bulletin 11/04/08 SB (25) 10 b. Install a new O-ring (part No. 446GC2149) to the EGR mixer tube mounting collar on the inlet manifold. Figure 10 EGR Mixer Tube O-Ring Installation 1. O-Ring (Part No. 446GC2149) 2. Inlet Manifold c. Position the mixer tube on the inlet manifold and install the two capscrews. Tighten the capscrews to 40 lb-ft (55 N m). d. Install the capscrew that attaches the support bracket to the side of the mixer tube and tighten to 40 lb-ft (55 N m). e. With the new seal in place, position the upper EGR cool tube on the mixer tube. Install the clamp and tighten the T-bolt to 110 lb-in (12 N m). f. Reconnect the boost pressure relief valve by reinstalling the coupling hose and tightening the hose clamps to 28 lb-in (3.1 N m). g. Reconnect the outlet pressure and temperature sensor harness connectors.

10 Service Bulletin 11/04/08 SB (25) 15. Continue with installation of the water pump inlet and static fill tubes. On certain chassis with the original thermostat housing (part No. 493GB520), the housing included a port for a vent line that was connected between the thermostat housing and the upper radiator tube. This port has been eliminated on the revised housings (part No. 493GB521P2). For chassis having this vent line, the line must be eliminated by removing the T-fitting from the upper radiator tube and then installing the existing 90-degree elbow fitting in the tube and reconnecting the line from the surge tank. 11 Figure 11 Surge Tank Vent Line 1. Upper Radiator Tube 2. Intake Air Duct 3. Install Elbow to Tube 4. Eliminate T-Fitting 5. Eliminate Line 6. Eliminate Elbow

11 Service Bulletin 11/04/08 SB (25) On chassis manufactured between January 2002 and July 2003, the oil cooler vent line may have been connected to a T-fitting in the surge tank vent line, between the thermostat housing and upper radiator tube as shown in the illustration below. When installing the revised thermostat housing (part No. 493GB521P2) on one of these chassis, the oil cooler vent line must be rerouted and connected to any available 1/8" port on the water manifold. If a 1/8" port is not available, an available 3/8" port may be used. The water manifold used on early ASET AC engines only had three available ports. If this is the case and there are no available 1/8" or 3/8" ports, the oil cooler vent line can be connected to one of the available 3/8" ports on the thermostat housing. When connecting to a 3/8" port, a reducer fitting (part No. 63AX1026 will be required. For optimum routing, elbow fittings (45-degree elbow fitting part No. 63AX3909 and 90-degree elbow fitting part No. 63AX3900) may be used. 12 Figure 12 Oil Cooler Vent Line (Chassis Manufactured Between January 2002 and July 2003) 1. To Upper Radiator Tube 2. Oil Cooler Vent Line

12 Service Bulletin 11/04/08 SB (25) Water Pump Inlet Tube/Static Fill Tube Installation Parts required for installation of the water pump inlet and static fill tubes are as follows: 13 Figure 13 Water Pump Inlet Tube and Static FIll Tube Key Qty. Part No. Description GC2145 O-ring GC5142 Water pump inlet tube AX1026 Hose clamps 4* 160AX543P36 Hose, 5/8" heater, 3" (7.62 mm) length GC516 Static fill tube 6 3** 63AX3488 Fittings, 90-degree elbow AM3 Bolt, M6 x 1.0 x 16 mm long with patch lock AX521P4 Hose, upper radiator tube-to-thermostat housing, silicone hose 1 11MF3682M10 Hose, upper radiator tube-to-thermostat housing, Gates Blue-Stripe AX979 Hose clamp, for silicone hose 2 560AM3 Hose clamp, for Gates Blue-Stripe hose *An additional 3 feet (0.91 M) length of 5/8" heater hose will be required to replace the cab heater return line. **Quantity dependent upon chassis equipment. In addition to the parts listed above, the following parts may also be required: Qty. Part No. Description 2 56AX393 O-rings, coolant conditioner mounting adapter (if equipped with coolant conditioner) 1 83AX827 Cushioned P-clamp, single hose 1 83AX722 Cushioned P-clamp, double hose

13 Service Bulletin 11/04/08 SB (25) Installation procedures for the water pump inlet tube and the static fill tube are as follows: 14 If not done previously, disconnect the batteries by disconnecting the negative battery cable(s) first, then the positive cable(s) and drain the coolant into a clean container. 1. Remove the Centri-Max oil filter cover and rotor. Cover the Centri-Max mounting adapter to prevent dirt entry. 2. If equipped with a coolant conditioner, remove the coolant conditioner canister and mounting adapter as an assembly. 15 Figure 14 Remove Coolant Conditioner Canister and Mounting Adapter 3. Remove the bolt securing the EECU harness clamp to the stand-off bracket below the EECU. Figure 15 EECU Harness Clamp

14 Service Bulletin 11/04/08 SB (25) Disconnect the harness connectors from the EECU, and then position the harnesses out of the way where they will not interfere with the remaining disassembly/reassembly procedures. 5. If there are coolant lines and/or fuel lines clamped to the stand-off bracket located at the top rear of the oil cooler, remove the fastener securing the clamp(s) to the bracket. Figure 16 Remove Fuel and Coolant Line Clamps from Stand-Off Bracket

15 Service Bulletin 11/04/08 SB (25) 6. Disconnect the fuel outlet line from the front fitting of the EECU cooling plate (leave the fuel inlet line connected). Avoid damaging the EECU cooling plate. Always hold the fitting boss on the cooling plate with a wrench when loosening or tightening the fuel inlet or outlet lines. 17 Figure 17 Disconnect Fuel Outlet Line from EECU Cooling Plate 1. Fuel Outlet Line (To Fuel Supply Pump) 2. Hold Cooling Plate Boss with a Wrench 3. EECU Cooling Plate 4. Fuel Inlet Line Disconnect the static fill hose from the elbow fitting located on the side of the thermostat housing. Figure 18 Disconnect Static Fill Line 8. Remove the EECU and cooling plate and position in a location where it will not interfere with the remaining procedures.

16 Service Bulletin 11/04/08 SB (25) Remove the lower radiator tube. Figure 19 Remove Lower Radiator Tube 10. Remove the thermostat bypass tube and the Y-shaped hose. 20 Figure 20 Remove Thermostat Bypass Tube and Y-Shaped Hose 1. Thermostat Bypass Tube 2. Y-Shaped Hose 11. Loosen the hose clamps securing the water pump inlet tube to the coupling hose at the oil cooler coolant outlet pipe.

17 Service Bulletin 11/04/08 SB (25) 12. Remove the bolt securing the wire harness to the tab on the water pump inlet tube and the three screws securing the tube to the water pump housing assembly. Remove the inlet tube. 21 Figure 21 Remove Water Pump Inlet Tube 13. Install a new O-ring (part No. 446GC2145) in the groove of the water pump inlet flange, and then apply a thin coating of MACK O-ring lubricant (part No. 243SX53) Water Pump Inlet Tube 1. O-Ring (Part No. 446GC2145) Figure 22 Install O-Ring

18 Service Bulletin 11/04/08 SB (25) 14. Install the new water pump inlet tube (part No. 670GC5142) by sliding the tube into the coupling hose at the oil cooler and then positioning the flange against the mounting surface. Use the existing screws to secure the tube to the water pump assembly. Tighten the screws to 40 lb-ft (55 N m). Tighten the hose clamp at the oil cooler-to-inlet tube coupling hose to 28 lb-in (3.1 N m). 15. Install a new oil cooler inlet screen (part No. 387GC32) into the Y-shaped oil cooler coolant inlet coupling hose. 23 Figure 23 Oil Cooler Inlet Screen 16. Reinstall the thermostat bypass tube to the elbow hose at the thermostat housing and to the coupling hose at the front of the engine. Tighten the hose clamps to 28 lb-in (3.1 N m). 17. Insert the cleaned coolant screen into the Y-shaped hose, and then install the hose. Tighten the clamps to 28 lb-in (3.1 N m). 18. Thoroughly clean the lower radiator tube, and then install the tube. Tighten the hose clamps to 28 lb-in (3.1 N m). 19. Reinstall the clamp that secures the lower radiator tube to the engine block. 20. Slide a hose clamp (part No. 83AX1026) over each end of a 3" (76.2 mm) length of 5/8" heater hose (part No. 160AX543P36), and then install the hose onto the spud on the water pump inlet tube. 21. Prepare the static fill tube (part No. 227GC516) for installation by removing the plugs from the spuds for the cab heater, sleeper heater return and fuel heater return lines as required, and then installing the fittings. Orient the fittings so that the open ends are facing in the approximate directions shown in the following illustration Oil Cooler Inlet Screen (Part No. 387GC32) Figure 24 Preparing Static Fill Tube for Installation 1. Fuel Heater Fitting 2. Cab Heater Fitting 3. Sleeper Heater Fitting

19 Service Bulletin 11/04/08 SB (25) If equipped with heater shut-off valves, install the existing shutoff valves in the static fill pipe instead of the elbow fittings. For sleeper equipped chassis, an additional shut-off valve will be required, because with the original heater return line routing, the sleeper return line and the cab return line are connected together with a coupling and share the same shut-off valve. 22. Install the static fill tube to the coupling hose at the water pump inlet tube and tighten the hose clamp to 28 lb-in (3.1 N m). 23. Reroute the static fill hose from the surge tank, and connect the hose to the static fill tube. Tighten the hose clamp to 28 lb-in (3.1 N m). For optimum routing, it may be necessary to cut the hose to the appropriate length. Be sure to leave enough slack in the static fill hose to allow for a full range of motion of the air suspended cab. For engines having the 493GB521 thermostat housing, it will be necessary to remove the 90-degree elbow fitting from the static fill port on the side of the housing and install a plug and O-ring (part No X16) in the port Plug with O-RIng (Part No X16) Figure 25 Thermostat Housing Plug The plug (part No X16) is only used if the engine is equipped with the 493GB521 thermostat housing.

20 Service Bulletin 11/04/08 SB (25) or optimum static fill hose routing on CXN and CHN model chassis, it may be necessary to reposition the clamp that secures the air conditioner hoses to the stand-off bracket located at the top of the engine by removing the clamp, rotating it 180 degrees and reinstalling as shown in the following illustration. 26 Figure 26 Repositioning Air Conditioner Hose Clamp

21 Service Bulletin 11/04/08 SB (25) 24. Reroute and connect the cab heater return, sleeper heater return (if equipped) and fuel heater return (if equipped) hoses to the appropriate connections on the static fuel tube as shown in the following illustration. For optimum routing, it may be necessary to cut the return hoses to proper length. On chassis equipped with a sleeper, the return lines for both the cab and sleeper heaters are connected together by a Y-coupling located near the thermostat housing. Disconnect the sleeper heater return line from the Y-coupling and disconnect the cab heater return line from the heater core. The cab heater return line must be replaced with a single length of hose. Approximately 3 feet (1 M) of hose will be required. 27 Figure 27 Coolant Return Hose Routing 1. To Surge Tank 2. Cab Heater Return 3. Sleeper Heater Return 4. Fuel Heater Return

22 Service Bulletin 11/04/08 SB (25) For chassis on which the cab, sleeper and fuel heater return lines are routed to the lower radiator tube, reroute the heater return lines to the static fill tube. Use the plugs removed from the static fill tube to close the ports in the lower radiator tube. On CXN and CHN models equipped with a fuel heater, it will be necessary to reorient the elbow fitting located in the fuel heater coolant outlet port toward the front. 28 Figure 28 Fuel Heater Return Line Fitting Orientation CXN and CHN Models 25. Reinstall the EECU/cooling plate assembly and tighten the upper and lower mounting nuts to 108 lb-in (12 N m). 26. Reconnect the fuel line to the outlet fitting of the cooling plate, and secure the cooling plate fuel inlet line to the stand-off bracket located at the rear of the oil cooler. Avoid damaging the EECU cooling plate. Always hold the fitting boss on the cooling plate with a wrench when loosening or tightening the fuel inlet or outlet lines.

23 Service Bulletin 11/04/08 SB (25) 27. Route and clamp the return lines and fuel lines to provide adequate clearance and to prevent rubbing and chafing. Use a new bolt (part No. 66AM3) to secure the static fill tube and the various coolant and fuel line clamps to the stand-off bracket located at the top rear of the oil cooler. Depending upon chassis model and equipment (sleeper, fuel heater, etc.), the coolant supply and return lines for the sleeper and fuel heater, and the fuel supply line to the EECU cooling plate were secured to the same stand-off bracket where the static fill tube is secured. With the coolant return lines rerouted to the static fill tube, only the coolant supply lines for the fuel heater and/or sleeper heater, along with the fuel supply line, will be clamped to the stand-off bracket. Use cushioned P-clamps (part No. 83AX722 for two hoses or part No. 83AX827 for a single hose) to secure the hose(s) to the stand-off bracket. Use tie wraps to secure the hoses as necessary to prevent rubbing and chafing. 29 Figure 29 Cab Heater, Sleeper Heater and Fuel Heater Line Routing Key Qty, Part No. Description AM3 Bolt, M6 x 1.0 x 16 mm long with patch lock AX722 P-clamp, cushioned (for two hoses) 1 83AX827 P-clamp, cushioned (for one hose)

24 Service Bulletin 11/04/08 SB (25) 28. Install a new radiator tube-to-thermostat housing coupling hose and new hose clamps. Tighten the hose clamps to 27.5 lb-in (3.1 N m). 30 Figure 30 Upper Radiator Tube Coupling Hose Key Qty, Part No. Description AX521P4 Hose, silicone, upper radiator tube-to-thermostat housing 1 11MF3682M10 Hose, Gates Blue Stripe, upper radiator tube-to-thermostat housing AX979 Clamps, for use with silicone hose 2 560AM3 Clamps, for use with Gates Blue Stripe hose 29. Reinstall the Centri-Max rotor and filter cover, and tighten the cover nut to 19 lb-ft (26 N m). 30. Install O-rings (part No. 56AX393) into the two ports on the coolant conditioner mounting adapter and apply a thin coating of MACK O-ring lubricant (part No. 243SX41). 31. Reinstall the coolant conditioner mounting adapter and canister. Tighten the mounting bolts to 15 lb-ft (20 N m). 32. Refill the cooling system with the same coolant that was originally drained. 33. Reconnect the batteries by connecting the positive battery cable(s) first, and then the negative cable(s). 34. Start the engine and check for coolant leaks. 35. Stop the engine and recheck the coolant level. Replenish with coolant as required, start the engine and recheck the coolant level as required until the cooling system has been thoroughly de-aerated.

25 Service Bulletin 11/04/08 SB (25) Reimbursement Expenses incurred for failed components will be reimbursed through the standard warranty claim process. Pro-active upgrades are not accepted as warrantable. Labor codes and maximum labor allowances are as follows: This Repair may be eligible for reimbursement if a product failure was experienced within the time and mileage limits of the applicable warranty coverage. Reimbursement is obtained via normal claim handling process. Claim Type (used only when uploading from the Dealer Bus. Sys.) 01 Labor Code Primary Labor Code Causal Part 215 9D hr., time allowed to remove and replace existing water pump inlet tube, install new static fill tube, reroute and connect cab heater coolant return line. Does not include take-charge time E hr., additional time to reroute and connect sleeper heater coolant return line. Does not include take-charge time F hr., additional time to reroute and connect fuel heater coolant return line. Does not include take-charge time G hr., Additional time to remove and replace thermostat housing. Does not include take-charge time. Not Applicable Mack Trucks, Inc. engages in a continuous program of testing and evaluating to provide the best possible product. Mack Trucks, Inc., however, is not committed to, or liable for updating existing chassis.

REVISED AIR GOVERNOR LINES CX AND CH MODEL CHASSIS WITH ASET AC ENGINE

REVISED AIR GOVERNOR LINES CX AND CH MODEL CHASSIS WITH ASET AC ENGINE SERVICE BULLETIN (Not applicable to Mack Trucks Australia) NUMBER: SB-531-011 DATE: 7/12/04 MODEL: CX, CH REVISED AIR GOVERNOR LINES CX AND CH MODEL CHASSIS WITH ASET AC ENGINE Effective June 2004, stainless

More information

JOHN DEERE GATOR HPX/XUV 2 PASSENGER HEATER INSTALLATION INSTRUCTIONS (p/n: 9PH20S30)

JOHN DEERE GATOR HPX/XUV 2 PASSENGER HEATER INSTALLATION INSTRUCTIONS (p/n: 9PH20S30) P. 1 of 12 JOHN DEERE GATOR HPX/XUV 2 PASSENGER HEATER INSTALLATION INSTRUCTIONS (p/n: 9PH20S30) Item: Qty: Description: 1 2 1 x 1 x 5/8 Tee Fitting 2 2 Plastic Snap-in Hose Grommet 3 4 1-1/2" Hose Clamps

More information

Product Support Bulletin

Product Support Bulletin MODEL: SUBJECT: CONVENTIONAL, W/ C7 CAT ENGINE WEBASTO TSL-17 HEATER Body DATE: APRIL 13, 2004 INDEX: 6 PAGE: 1 OF 16 Before you start this procedure, perform Freightliner Service Bulletin #20-7 first.

More information

Service Bulletin

Service Bulletin Service Bulletin 15-010 February 17, 2017 05854 Version 4 MIL Comes On with DTC P2422 Supersedes 15-010, dated December 3, 2015; See REVISION SUMMARY AFFECTED VEHICLES Year Model Trim VIN Range 2013 17

More information

INSTALLATION INSTRUCTIONS John Deere One Series; 1023E, 1025R and 1026R Models A HEATER KIT. Figure 1 (General Layout and Parts I.D.

INSTALLATION INSTRUCTIONS John Deere One Series; 1023E, 1025R and 1026R Models A HEATER KIT. Figure 1 (General Layout and Parts I.D. A-11978 HEATER KIT Figure 1 (General Layout and Parts I.D.) Read these instructions and identify all components. Please retain these instructions for future reference and parts ordering information. Refer

More information

When checking the vehicle for DTCs, the ECM may report one or more of the following DTCs set as current or in history: P0442, P0446, P0449 or P0455.

When checking the vehicle for DTCs, the ECM may report one or more of the following DTCs set as current or in history: P0442, P0446, P0449 or P0455. 2006 GMC Sierra 5.3L Eng 1500 CHECK ENGINE LIGHT ON, FUEL TANK HARD TO FILL, DTCS P0442, P0446, P0455 OR P0449 SET (REPLACE EVAPORATIVE EMISSION (EVAP) VENT VALVE SOLENOID ASSEMBLY AND ADD/RELOCATE FILTER

More information

PERFECT FIT IN-DASH HEAT/ COOL/ DEFROST PLYMOUTH BELVEDERE

PERFECT FIT IN-DASH HEAT/ COOL/ DEFROST PLYMOUTH BELVEDERE PERFECT FIT IN-DASH HEAT/ COOL/ DEFROST 1966-67 PLYMOUTH BELVEDERE CONTROL & OPERATING INSTRUCTIONS The controls on your new Perfect Fit system. Offers complete comfort capabilities in virtually every

More information

Document ID: The EVAP canister vent solenoid (CVS) valve draws fresh air into the system through a vent.

Document ID: The EVAP canister vent solenoid (CVS) valve draws fresh air into the system through a vent. Page 1 of 9 Document ID: 2792052 #02-06-04-037J: Check Engine Light On, Fuel Tank Hard to Fill, DTCs P0442, P0446, P0455 or P0449 Set (Replace Evaporative Emission (EVAP) Vent Valve Sloenoid Assembly and

More information

Heater Core Replacement

Heater Core Replacement Page 1 of 14 2003 Chevrolet Impala : Heating, Ventilation, & Air Conditioning > Repair Instructions > Heater Core Replacement Heater Core Replacement HEATER CORE REPLACEMENT Tools Required J 38185 (Image

More information

Engine Block Heater Service Kits (Tank Type) 30RZ/33RZ/45RZ (CSG 649 Ford Powered) Standby Generator Sets

Engine Block Heater Service Kits (Tank Type) 30RZ/33RZ/45RZ (CSG 649 Ford Powered) Standby Generator Sets TT 880 INSTRUCTIONS 7/92 Engine Block Heater Service Kits (Tank Type) 30RZ/33RZ/45RZ (CSG 649 Ford Powered) Standby Generator Sets Model Voltage Kit No. All Models 120 276380 All Models 240 276381 This

More information

Heater with Air Conditioning. E-Series Ford Aeromaster

Heater with Air Conditioning. E-Series Ford Aeromaster Service Guide Heater with Air Conditioning E-Series Ford Aeromaster Contents Blower Motor...2 Plenum Removal...3 Control Module...6 Servo Motors...8 Coolant Valve and Servo Motor...8 Evaporator Recirculation

More information

PERFECT FIT IN-DASH HEAT/ COOL/ DEFROST 1968 CHEVROLET IMPALA

PERFECT FIT IN-DASH HEAT/ COOL/ DEFROST 1968 CHEVROLET IMPALA specializing in AIR CONDITIONING, PARTS AND SYSTEMS for your classic vehicle PERFECT FIT IN-DASH HEAT/ COOL/ DEFROST 1968 CHEVROLET IMPALA CONTROL & OPERATING INSTRUCTIONS The controls on your new Perfect

More information

specializing in AIR CONDITIONING, PARTS AND SYSTEMS for your classic hi l PERFECT FIT SERIES IN-DASH HEAT/ COOL/ DEFROST FORD TRUCK

specializing in AIR CONDITIONING, PARTS AND SYSTEMS for your classic hi l PERFECT FIT SERIES IN-DASH HEAT/ COOL/ DEFROST FORD TRUCK specializing in AIR CONDITIONING, PARTS AND SYSTEMS for your classic hi l PERFECT FIT SERIES IN-DASH HEAT/ COOL/ DEFROST 1967-72 FORD TRUCK CONTROL & OPERATING INSTRUCTIONS The controls on your new Perfect

More information

PERFECT FIT IN-DASH HEAT/ COOL/ DEFROST FORD PICKUP

PERFECT FIT IN-DASH HEAT/ COOL/ DEFROST FORD PICKUP specializing in AIR CONDITIONING, PARTS AND SYSTEMS for your classic vehicle PERFECT FIT IN-DASH HEAT/ COOL/ DEFROST 1960-66 FORD PICKUP CONTROL & OPERATING INSTRUCTIONS The controls on your new Perfect

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS Accessory Application Publication No. HEATER KIT P/N 0SE01-HL3-102 (SXS700M2/M4) P/N 0SE01-HL3-103 (SXS700M2D/M4D) SXS700M2/M2D/M4/M4D MII 14607-15172 Issue Date REVISED: June

More information

Dirt and dust intrusion into the EVAP canister vent hose assembly, resulting in restricted air flow, may cause this condition.

Dirt and dust intrusion into the EVAP canister vent hose assembly, resulting in restricted air flow, may cause this condition. #02-06-04-037H: DTC P0446 (Restricted/Blocked EVAP Vent Path) Set, Check Engine Light On (Replace Evaporative Emission (EVAP) Vent Valve Solenoid Assembly and Add/Relocate Filter Box Using Service Kit)

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS Accessory Application Publication No. INSTALLATION INSTRUCTIONS HEATER KIT P/N 0SE01-HL3-101 SXS700M4/M2 Honda Dealer: Please give a copy of these instructions to your customer. PARTS LIST REPAIR KIT (P/N

More information

A HEATER KIT With Diesel Engine Connection Fittings

A HEATER KIT With Diesel Engine Connection Fittings A-12142 HEATER KIT With Diesel Engine Connection Fittings Figure 1 (General Layout and Parts I.D.) Page 1 of 6 Read these instructions and identify all components. Please retain these instructions for

More information

JOHN DEERE X465, X475, X485, X495, X575, X585

JOHN DEERE X465, X475, X485, X495, X575, X585 JOHN DEERE X465, X475, X485, X495, X575, X585 and X595 X700 SERIES (X700, X720, X720se, X724, X728, X728se, X729, X740, X744, X748, X748se, X749) CAB MOUNTING INSTRUCTIONS A-11271 Manufactured by: BOX

More information

569, 570, 571, 572 Series

569, 570, 571, 572 Series Please read and save this Repair Parts Manual. Read this manual and the General Operating Instructions carefully before attempting to assemble, install, operate or maintain the product described. Protect

More information

TECHNICAL INSTRUCTIONS

TECHNICAL INSTRUCTIONS TECHNICAL INSTRUCTIONS 24-Month Maintenance Kit P/N 58025-06 For BMK2.0LN Boilers Description of Document: This TID provides the procedures to perform recommended 24-Month maintenance on the following

More information

Kawasaki Teryx Firestorm Heater Kit Instructions.

Kawasaki Teryx Firestorm Heater Kit Instructions. Please read all instructions before beginning installation. When working on cooling systems always allow vehicles to cool to avoid being burned or scalded by hot coolant. Always disconnect vehicle s negative

More information

568X, 587X, 588X Series

568X, 587X, 588X Series Please read and save this Repair Parts Manual. Read this manual and the General Operating Instructions carefully before attempting to assemble, install, operate or maintain the product described. Protect

More information

HEATING AND AIR CONDITIONING

HEATING AND AIR CONDITIONING WJ HEATING AND AIR CONDITIONING 24-1 HEATING AND AIR CONDITIONING TABLE OF CONTENTS page SERVICE PROCEDURES REFRIGERANT OIL LEVEL...1 REFRIGERANT RECOVERY....1 REFRIGERANT SYSTEM CHARGE...1 REFRIGERANT

More information

PERFECT FIT SERIES IN-DASH HEAT/ COOL/ DEFROST CHEVROLET CHEVELLE/ EL CAMINO NOTE: INSTRUCTIONS DEPICT CHEVELLE

PERFECT FIT SERIES IN-DASH HEAT/ COOL/ DEFROST CHEVROLET CHEVELLE/ EL CAMINO NOTE: INSTRUCTIONS DEPICT CHEVELLE specializing in AIR CONDITIONING, PARTS AND SYSTEMS for your classic vehicle PERFECT FIT SERIES IN-DASH HEAT/ COOL/ DEFROST 1964-65 CHEVROLET CHEVELLE/ EL CAMINO NOTE: INSTRUCTIONS DEPICT CHEVELLE CONTROL

More information

PERFECT FIT SERIES IN-DASH HEAT/ COOL/ DEFROST CHEVROLET NOVA

PERFECT FIT SERIES IN-DASH HEAT/ COOL/ DEFROST CHEVROLET NOVA specializing in AIR CONDITIONING, PARTS AND SYSTEMS for your classic PERFECT FIT SERIES IN-DASH HEAT/ COOL/ DEFROST 1966-67 CHEVROLET NOVA CONTROL & OPERATING INSTRUCTIONS The controls on your new Perfect

More information

Hose Clamps, Charge Air Cooler, Replacement page 2

Hose Clamps, Charge Air Cooler, Replacement page 2 Volvo Trucks North America Greensboro, NC USA DService Bulletin Trucks Date Group No. Page 5.2008 265 24 1(9) Hose Clamps, Charge Air Cooler, Replacement D11F, D13F and D16F Cummins ISX Hose Clamps, Charge

More information

INSIDE ENGINE COMPARTMENT TOYOTA AIR CONDITIONING ENGLISH EUROPE

INSIDE ENGINE COMPARTMENT TOYOTA AIR CONDITIONING ENGLISH EUROPE INSIDE ENGINE COMPARTMENT TOYOTA AIR CONDITIONING ENGLISH EUROPE INTRODUCTION IMPORTANT NOTICE This manual has been designed for technicians who are qualified and educated in the proper procedures of vehicle

More information

569, 570, 571, 572 Series

569, 570, 571, 572 Series Please read and save this Repair Parts Manual. Read this manual and the General Operating Instructions carefully before attempting to assemble, install, operate or maintain the product described. Protect

More information

When checking the vehicle for DTCs, the ECM may report one or more of the following DTCs set as current or in history: P0442, P0446, P0449 or P0455.

When checking the vehicle for DTCs, the ECM may report one or more of the following DTCs set as current or in history: P0442, P0446, P0449 or P0455. TECHNICAL Bulletin No.: 02-06-04-037J Date: March 20, 2012 Subject: Check Engine Light On, Fuel Tank Hard to Fill, DTCs P0442, P0446, P0455 or P0449 Set (Replace Evaporative Emission (EVAP) Vent Valve

More information

TT /97 WARNING WARNING WARNING INSTALLATION INSTRUCTIONS

TT /97 WARNING WARNING WARNING INSTALLATION INSTRUCTIONS TT-116 2/97 INSTALLATION INSTRUCTIONS Original Issue Date: 2/97 Model: 900/1000 kw Market: Industrial Subject: Block Heater Kits PA-28648, PA-28648-SD The block heater kit heats engine coolant, making

More information

REMOVE AND INSTALL AIR CLEANER ASSEMBLY

REMOVE AND INSTALL AIR CLEANER ASSEMBLY REMOVE AND INSTALL AIR CLEANER ASSEM 50 DISASSEM AND ASSEM- REMOVE AND INSTALL AIR CLEANER ASSEM Cover Connector Air cleaner assembly Place the machine on a level ground, lower the work equipment to the

More information

TECHNICAL INSTRUCTIONS

TECHNICAL INSTRUCTIONS TECHNICAL INSTRUCTIONS 24-Month Maintenance Kit P/N 58025-04 For BMK3.0LN Boilers Description of Document: This TID provides the procedures to perform recommended 24-Month maintenance on the following

More information

TECHNICAL INSTRUCTIONS

TECHNICAL INSTRUCTIONS TECHNICAL INSTRUCTIONS 12-Month Maintenance Procedures These instructions apply to the following BMK boiler models (Standard & Dual Fuel): Benchmark 1.5LN Benchmark 2.0LN Benchmark 3.0LN Benchmark 750

More information

Heating and ventilation system,

Heating and ventilation system, Page 1 of 24 87-151 Heating and ventilation system, servicing Instrument panel air outlets and air guide ducts CAUTION! Before working on the electrical system: Obtain security code for anti-theft radio.

More information

INSTRUCTION BULLETIN

INSTRUCTION BULLETIN INSTRUCTION BULLETIN No. 340853 Machine: M20 / T20 Published: 12-2015 Rev. 03 NOTE: DO NOT DISCARD the Parts List from the Instruction Bulletin. Place the Parts List in the appropriate place in the machine

More information

Patterson/AMT Inline Circulator Pump Refer to pump manual for General Operating and Safety Instructions.

Patterson/AMT Inline Circulator Pump Refer to pump manual for General Operating and Safety Instructions. Please read and save this Repair Parts Manual. Read this manual and the General Operating Instructions carefully before attempting to assemble, install, operate or maintain the product described. Protect

More information

Installation Instructions Part No , Part No Part No

Installation Instructions Part No , Part No Part No Torsion-Flex Motor mount for PSC motors and Rigid-Mount for ECM motors Replacement Kit Cancels: New Installation Instructions Part No. 327752-401, Part No. 327753-401 Part No. 327754-401 IIK-310A-45-11

More information

2002 Dodge Caravan SE

2002 Dodge Caravan SE EVAPORATOR (FRONT) Removal 1. Remove the HVAC housing from the vehicle. See HVAC HOUSING (FRONT). Remove the heater hoses from the heater core. 2. Remove and discard the foam seal from the HVAC housing

More information

PERFECT FIT IN-DASH HEAT/ COOL/ DEFROST EARLY 1955 CHEVROLET PICKUP

PERFECT FIT IN-DASH HEAT/ COOL/ DEFROST EARLY 1955 CHEVROLET PICKUP specializing in AIR CONDITIONING, PARTS AND SYSTEMS for your classic vehicle PERFECT FIT IN-DASH HEAT/ COOL/ DEFROST 1947 - EARLY 1955 CHEVROLET PICKUP CONTROL & OPERATING INSTRUCTIONS The controls on

More information

Patterson/AMT Inline Circulator Pump Refer to pump manual for General Operating and Safety Instructions.

Patterson/AMT Inline Circulator Pump Refer to pump manual for General Operating and Safety Instructions. Please read and save this Repair Parts Manual. Read this manual and the General Operating Instructions carefully before attempting to assemble, install, operate or maintain the product described. Protect

More information

The Marine Throne. Model TMT S/37045/X-Series QUIET - FLUSH ELECTRIC TOILET. "all the comforts of home" FEATURES SPECIFICATIONS INSTALLATION

The Marine Throne. Model TMT S/37045/X-Series QUIET - FLUSH ELECTRIC TOILET. all the comforts of home FEATURES SPECIFICATIONS INSTALLATION The Marine Throne "all the comforts of home" Model TMT S/37045/X-Series QUIET - FLUSH ELECTRIC TOILET FEATURES Very quiet flush cycle - like a household toilet Single button flush actuator - with dual

More information

Patterson/AMT Inline Circulator Pump Refer to pump manual for General Operating and Safety Instructions.

Patterson/AMT Inline Circulator Pump Refer to pump manual for General Operating and Safety Instructions. Please read and save this Repair Parts Manual. Read this manual and the General Operating Instructions carefully before attempting to assemble, install, operate or maintain the product described. Protect

More information

HEAT/ COOL/ DEFROST FORD THUNDERBIRD

HEAT/ COOL/ DEFROST FORD THUNDERBIRD specializing in AIR CONDITIONING, PARTS AND SYSTEMS for your classic vehicle PERFECT FIT IN-DASH HEAT/ COOL/ DEFROST 1964-66 FORD THUNDERBIRD CONTROL & OPERATING INSTRUCTIONS The controls on your new Perfect

More information

50 Disassembly and assembly Cab and its attachments

50 Disassembly and assembly Cab and its attachments When adjustment is needed after performing check in step 8; 3) Close front window assembly (1). 4) Loosen locknuts (26) of right and left rubber stoppers (24) and move the stoppers backward so that front

More information

REF. NO Clamp Assembly 8 1 set Gasket (4 per set) S.S. Lock-washer 3/8 x 1/ Brass Impeller 3.

REF. NO Clamp Assembly 8 1 set Gasket (4 per set) S.S. Lock-washer 3/8 x 1/ Brass Impeller 3. 4.4 SUPPLY PUMPAK ASSEMBLY NOTE: This section applies only to systems, which include a supply pumpak. Only the H6, XA, and XC series systems contain a supply pumpak. If your system is a single zone, H6

More information

TECHNICAL INSTRUCTIONS

TECHNICAL INSTRUCTIONS TECHNICAL INSTRUCTIONS 24-Month Maintenance Kit P/N 58015-02 For BMK2.0 (Nozzle Mix) Description of Document: This TID provides the procedures to perform recommended 24-Month maintenance on the following

More information

Air Heater. Air Top 3500 Diesel. Supplemental Installation Instructions for: Van Body Vehicles

Air Heater. Air Top 3500 Diesel. Supplemental Installation Instructions for: Van Body Vehicles Air Heater Air Top 3500 Diesel Supplemental Installation Instructions for: Van Body Vehicles Table of Contents 1. Introduction 1.1 General Information.............................................. 2 2.

More information

BC BRONCOS AIR CONDITIONING UNIT

BC BRONCOS AIR CONDITIONING UNIT BC BRONCOS AIR CONDITIONING UNIT CAUTION If you are not familiar with the principals of air conditioning, have an authorized air conditioning technician evacuate and charge the system. Serious damage to

More information

Installation and Maintenance "L" and "LS" Series

Installation and Maintenance L and LS Series Installation and Maintenance "L" and "LS" Series IB-43-E This bulletin should be used by experienced personnel as a guide to the installation and maintenance of "L" and "LS" Series ultra capacity float

More information

Heater for BRP Commander. Caution: Before using this product, read this manual and follow all safety instructions. Owner s Manual

Heater for BRP Commander. Caution: Before using this product, read this manual and follow all safety instructions. Owner s Manual Owner s Manual Model: Can Am Commander Heater for BRP Commander Caution: Before using this product, read this manual and follow all safety instructions. Safety Instructions Kit Contents Tool Requirement

More information

Parts & Material Included

Parts & Material Included O² Hydro Well System Installation, Use & Care Guide Parts & Material Included 1. Funnel 11. Drain Line 21. Air Head 2. Media Tank Distributer Tube 12. Air Release 22. Drain Fitting 3. Air Tank Distributer

More information

ModulAir Air Dryer with External Purge Tank - Changeover from Bendix AD-IS for Peterbilt Installation. Air Dryer Mounting Bracket (Item 1)

ModulAir Air Dryer with External Purge Tank - Changeover from Bendix AD-IS for Peterbilt Installation. Air Dryer Mounting Bracket (Item 1) Instruction Guide L31259 11/10 ModulAir Air Dryer with External Purge Tank - Changeover from Bendix AD-IS for Peterbilt Installation Air Dryer Mounting Bracket (Item 1) Tank Mounting Bracket (Item 19)

More information

Sedan Range. Remove and destroy Bulletin 14-13, amended 10/97. Replace with this Bulletin. Revised text is marked with a bar and in bold text.

Sedan Range. Remove and destroy Bulletin 14-13, amended 10/97. Replace with this Bulletin. Revised text is marked with a bar and in bold text. SERVICE Sedan Range DATE 8/97 Amended 10/98 TECHNICAL BULLETIN Poor Heater Performance Coolant Specification Change Replace Coolant With Heater Core Remove and destroy Bulletin 14-13, amended 10/97. Replace

More information

Armstrong J Series Float, Thermostatic Steam Traps, Condensate Controllers & Liquid Drainers Installation and Maintenance Manual

Armstrong J Series Float, Thermostatic Steam Traps, Condensate Controllers & Liquid Drainers Installation and Maintenance Manual Armstrong J Series, Thermostatic Steam Traps, Condensate Controllers & Liquid Drainers Installation and Maintenance Manual This bulletin should be used by experienced personnel as a guide to the installation

More information

This site is based on a but applies to all 1971-on Saab 99 and Saab 900.

This site is based on a but applies to all 1971-on Saab 99 and Saab 900. by Mark Jeter updated: December 8, 2004 originally web-published June 27, 2001 This document shows how the original waterpump in a Saab "B" engine can be eliminated and replaced with a reliable, efficient

More information

C-IV 60 CEILING FAN READ AND SAVE THESE INSTRUCTIONS. FAN RATING AC 120V. 60Hz

C-IV 60 CEILING FAN READ AND SAVE THESE INSTRUCTIONS. FAN RATING AC 120V. 60Hz C-IV 60 CEILING FAN READ AND SAVE THESE INSTRUCTIONS FAN RATING AC 120V. 60Hz Please do not use any electric or battery powered tools in the assembly and installation of this or any Matthews Fan Company

More information

INTRODUCTION. NOTE: Read the entire instruction manual before starting the installation. FIRE, EXPLOSION, ELECTRICAL SHOCK HAZARD

INTRODUCTION. NOTE: Read the entire instruction manual before starting the installation. FIRE, EXPLOSION, ELECTRICAL SHOCK HAZARD Installation Instructions NOTE: Read the entire instruction manual before starting the installation. SAFETY CONSIDERATIONS Improper installation, adjustment, alteration, service, maintenance, or use can

More information

HX Field Replacement Kit

HX Field Replacement Kit Quantity Kit Part Number Description PE 110 Natural Gas Stainless Steel Condensate Pan PT 110 Natural Gas Polypropylene Condensate Pan Model PE 110 LP Stainless Steel Condensate Pan PT 110 LP Polypropylene

More information

MOUNTING INSTRUCTIONS

MOUNTING INSTRUCTIONS John Deere HPX and XUV Heater Kit 4-14916 MOUNTING INSTRUCTIONS With replacement parts drawing BOX 70 LITCHFIELD, MINNESOTA 55355-0070 (320) 693-3221 Fax: (320) 693-7252 Visit our web site at: www.800cabline.com

More information

COOLING SYSTEM 1. Section V CONTENTS DATA AND SPECIFICATIONS. Page. Fluid Fan Drive (Silent Flite) 3. Water Pump 4. Radiator 5

COOLING SYSTEM 1. Section V CONTENTS DATA AND SPECIFICATIONS. Page. Fluid Fan Drive (Silent Flite) 3. Water Pump 4. Radiator 5 Section V COOLING SYSTEM CONTENTS Fluid Fan Drive (Silent Flite) 3 Water Pump 4 Radiator 5 Water Temperature Gauge 6 Thermostat 7 Radiator Pressure Cap 7 Service Diagnosis 7 DATA AND SPECIFICATIONS COOLING

More information

Single-Control Lavatory Faucet

Single-Control Lavatory Faucet P22740 P23201 P24407 1 of 5 Thank You For Choosing KALLISTA We appreciate your commitment to KALLISTA quality products. Please take a moment to review this manual before you install your KALLISTA product.

More information

COMBUSTION AIR SYSTEM

COMBUSTION AIR SYSTEM COMBUSTION AIR SYSTEM MODEL: CAS-2WM WEIL-MCLAIN OUTSIDE AIR KIT FOR USE WITH OIL BURNER MODELS QB-180 & QB-300 4" VRV 4" IAH HOOD AIR BOOT TM The Air Boot model CAS-2WM is for use only on the designated

More information

MOUNTING INSTRUCTIONS

MOUNTING INSTRUCTIONS A-12093 JDX 2014 HEATER KIT With Gas Engine Connection Fittings 2014 and Newer ROPS Cabs A-12098 (Kit A-12092, Diesel Engine Connection Fittings are sold separately for diesel models) 12VDC, 2-Speed, 15,000

More information

HVAC Module Assembly Replacement. Tools Required. J A Halogen Leak Detector. Removal Procedure

HVAC Module Assembly Replacement. Tools Required. J A Halogen Leak Detector. Removal Procedure 2005 Pontiac Grand AM V6-3.4L VIN E Page 1 Housing Assembly HVAC: Service and Repair The content of this article reflects the changes identified in TSB Bulletin No. #06-01-37-002 dated January 18, 2006.

More information

Sleeper Heater and Air Conditioner, Blend Air System 83.05

Sleeper Heater and Air Conditioner, Blend Air System 83.05 Sleeper Heater and Air Conditioner, Blend Air System 8.0 General Information General Description The sleeper heater and air conditioner assembly is mounted in either the baggage compartment or under the

More information

ASSEMBLY and INSTALLATION INSTRUCTIONS. Pipe wrench Ratchet 3/8 socket 9/16 socket 11/16 socket 3/16 Allen key 3/32 Allen key 9/64 Allen key

ASSEMBLY and INSTALLATION INSTRUCTIONS. Pipe wrench Ratchet 3/8 socket 9/16 socket 11/16 socket 3/16 Allen key 3/32 Allen key 9/64 Allen key ASSEMBLY and INSTALLATION INSTRUCTIONS Gas Conversion Kit Tube Heaters View these instructions online at www.lbwhite.com Kit Contents: DESCRIPTION QTY. Instructions 1 Burner orifi ce 1 Manifold pipe 1

More information

Page 1 of 5 #02-06-04-037F: DTC P0446 (Restricted/Blocked EVAP Vent Path) Set, Check Engine Light On (Replace Evaporative Emission (EVAP) Vent Valve Solenoid Assembly and Add/Relocate Filter Box Using

More information

Safety. Rinse Kit for Multi-Pro 1200 and 1250 Turf Sprayers Model No Safety and Instructional Decals. Installation Instructions

Safety. Rinse Kit for Multi-Pro 1200 and 1250 Turf Sprayers Model No Safety and Instructional Decals. Installation Instructions Rinse Kit for Multi-Pro 1200 and 1250 Turf Sprayers Model No. 106-4842 Form No. 3353-529 Rev B Installation Instructions Note: Determine the left and right sides of the machine from the normal operating

More information

Thermo-Bob 4 Installation Manual KT5A Kit

Thermo-Bob 4 Installation Manual KT5A Kit Thermo-Bob 4 Installation Manual KT5A Kit 2009-2016 KTM 400/450/500 EXC, XC-W 2008-2011 KTM 530 EXC-R 2011 Husaberg FS510 2013-2014 Husaberg FE501 2014-2016 Husqvarna FE501 IM TB4-KT5A V1 Watt-man.com

More information

TECHNICAL INSTRUCTIONS

TECHNICAL INSTRUCTIONS TECHNICAL INSTRUCTIONS Benchmark 3.0LN 24-Month Maintenance Kit# 58015-04 This kit applies to units with an Ignitor and a separate gas injector. For units with an Ignitor-Injector (P/N 58023), see Kit

More information

Model Series. PumpAgents.com - buy pumps and parts online QUIET - FLUSH ELECTRIC TOILET. Model Series FEATURES SPECIFICATIONS INSTALLATION

Model Series. PumpAgents.com - buy pumps and parts online QUIET - FLUSH ELECTRIC TOILET. Model Series FEATURES SPECIFICATIONS INSTALLATION PumpAgents.com - Click here for Pricing/Ordering Model 37045-Series QUIET - FLUSH ELECTRIC TOILET FEATURES Very quiet flush cycle - like a household toilet Single button flush actuator - with dual function

More information

Engine Block Heater Service Kits (Tank Type) ROZJ 6076T and 6076A (John Deere Powered Standby Generator Sets)

Engine Block Heater Service Kits (Tank Type) ROZJ 6076T and 6076A (John Deere Powered Standby Generator Sets) TT 760 INSTRUCTIONS 8/91 Engine Block Heater Service Kits (Tank Type) 125 180ROZJ 6076T and 6076A (John Deere Powered Standby Generator Sets) Model Voltage Kit No. 125 150ROZJ 120 276511 125 150ROZJ 240

More information

Installation Manual Mopar Engine Compartment Upgrade Kit

Installation Manual Mopar Engine Compartment Upgrade Kit Installation Manual 64-75 Mopar Engine Compartment Upgrade Kit Congratulations... You have just purchased the highest quality, best performing A/C system upgrade ever designed for your Classic Vehicle.

More information

UB1 AIR CONDITIONING UNIT INSTALLATION INSTRUCTIONS

UB1 AIR CONDITIONING UNIT INSTALLATION INSTRUCTIONS UB1 AIR CONDITIONING UNIT INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS: Carefully read these instructions before installing your new air-conditioner. AUSTRALIAN AUTOMOTIVE AIR AL00500054E 1 Table

More information

Installation. Leveling

Installation. Leveling Your refrigerator was packed carefully for shipment. Remove and discard shelf packaging and tape. Do not remove the serial plate. Location Do not install refrigerator near oven, radiator or other heat

More information

an ISO 9001:2008 Registered Company ShortPac HEAT/COOL (05000-QUX-A/05000-VUX-A)

an ISO 9001:2008 Registered Company ShortPac HEAT/COOL (05000-QUX-A/05000-VUX-A) an ISO 9001:2008 Registered Company ShortPac (05000-QUX-A/05000-VUX-A) 18865 GOLL ST. - SAN ANTONIO, TX. - 78266 - ph.210-654-7171 - fax 210-654-3113 900499 REV C 3/7/14, ShortPac EVAPORATOR KIT PG 1 OF

More information

Camaro A/C Install Instructions

Camaro A/C Install Instructions 1967-1968 Camaro A/C Install Instructions This kit is designed for the 1967-1968 non A/C equipped Camaro. This kit can be used with or without Astro vents Step One Remove the following factory components:

More information

Installation Manual. TriPac. Auxiliary Heating and Cooling Temperature Management System. TK IM (Rev. 13, 01/12)

Installation Manual. TriPac. Auxiliary Heating and Cooling Temperature Management System. TK IM (Rev. 13, 01/12) Installation Manual TriPac Auxiliary Heating and Cooling Temperature Management System TK 53120-19-IM (Rev. 13, 01/12) Installation Manual TriPac Auxiliary Heating and Cooling Temperature Management System

More information

HEATING AND VENTILATION

HEATING AND VENTILATION SECTION 14-102.04 14-102.04/ 1 2007OC19 DESCRIPTION The heating, ventilation and air conditioning (HVAC) system is designed to optimize passenger comfort. The system regulates interior vehicle atmosphere,

More information

SAN JUAN FRESH WATER COOLING SYSTEMS

SAN JUAN FRESH WATER COOLING SYSTEMS SAN JUAN FRESH WATER COOLING SYSTEMS 4.3-5.7 GI VOLVO Block Only Cooling, Mounted Off Engine Kit #V-111 Installation Instructions San Juan Engineering Heat Exchangers provide thermostatically controlled

More information

CABS/BLADES/ SPREADERS/ACCESSORIES

CABS/BLADES/ SPREADERS/ACCESSORIES JOHN DEERE 3000 SERIES (4200/4300/4400) (4210/4310/4410) (3120/3320/3520/3720) JOHN DEERE 4000 SERIES (4500/4600/4700) (4510/4610/4710) (4120/4320/4520/4720) OPTIONAL AUXILIARY HEATER INSTALLATION (p/n

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS ,t_2007 Lennox Industries Inc. Dallas, Texas, USA INSTALLATION INSTRUCTIONS CH33 Series Units EVAPORATOR 505,264M (65484504) 10/07 Supersedes 09/06 COILS n _putech blications ical Litho U.S.A. RETAIN THESE

More information

Installation Manual PS-200 & PS-201

Installation Manual PS-200 & PS-201 Installation Manual PS-200 & PS-201 Table of Contents Pre-Uncrating Checklist... 1 Verifying System Requirements... 2 Verifying System Direction... 2 Verifying the Electrical Requirements... 2 Removal

More information

Model Series ELECTRIC WATER SYSTEM PUMP. PumpAgents.com - buy pumps and parts online. Model Series. Automatic Multi-Outlet FEATURES

Model Series ELECTRIC WATER SYSTEM PUMP. PumpAgents.com - buy pumps and parts online. Model Series. Automatic Multi-Outlet FEATURES PumpAgents.com - Click here for Pricing/Ordering Model 36950-2 Series ELECTRIC WATER SYSTEM PUMP Automatic Multi-Outlet FEATURES Self-Priming Diaphragm Design Allows Dry Running Built-in Discharge Check

More information

Audi-Larm Audible Alarm

Audi-Larm Audible Alarm Audi-Larm Audible Alarm MAINTENANCE AND REPAIR TAL 1706 (L) Rev. 7 MSA 2017 Prnt. Spec. 10000005389(I) Mat. 10093084 Doc. 10093084 REPLACEMENT KITS AND PARTS LIST TAL 1706 (L) Rev. 7-10093084 2 Exploded

More information

Installation Manual PS-225 & PS-275

Installation Manual PS-225 & PS-275 Installation Manual PS-225 & PS-275 Table of Contents Pre-Uncrating Checklist... 1 Verifying System Requirements... 2 Verifying System Direction... 2 Verifying the Electrical Requirements... 2 Removal

More information

CEILING FAN OWNER'S MANUAL

CEILING FAN OWNER'S MANUAL CEILING FAN OWNER'S MANUAL READ AND SAVE THESE INSTRUCTIONS MODEL: 52-135-5WA-13 FAN RATING AC 120V. 60Hz CUL LISTED MODEL : AC-552OD 1. TOOLS AND MATERIALS REQUIRED Philips screw driver Blade screw driver

More information

INSTALLATION. Glass Panel Doors (select models) CAUTION

INSTALLATION. Glass Panel Doors (select models) CAUTION Location Do not install refrigerator near oven, radiator or other heat source. If not possible, shield refrigerator with cabinet material. Do not install where temperature falls below 55 F (13 C) or rises

More information

pushing the tube into the rear of the water outlet housing with a slight twisting motion to evenly distribute the adhesive. After cleaning off any ext

pushing the tube into the rear of the water outlet housing with a slight twisting motion to evenly distribute the adhesive. After cleaning off any ext I chose an original FE expansion tank that had the filler neck on the driver's side of the tank but still had the radiator hose outlet facing the passenger side. I figured using such a tank would afford

More information

Built-In Dishwasher. Installation Instructions. BEFORE YOU BEGIN Read these instructions completely and carefully. IMPORTANT The dishwasher MUST be

Built-In Dishwasher. Installation Instructions. BEFORE YOU BEGIN Read these instructions completely and carefully. IMPORTANT The dishwasher MUST be Installation Instructions Built-In Dishwasher If you have questions, call 800.GE.CARES (800.432.2737) or visit our website at: www.ge.com BEFORE YOU BEGIN Read these instructions completely and carefully.

More information

General System Layout Sketch

General System Layout Sketch General System Layout Sketch EZ-37 Solar Panels PV panel Can use Standard Copper, CPVC or PEX Pipes Pump Existing Water Heater Bottom Feed Connector 1 Introduction This document describes how to install

More information

INSTALLATION INSTRUCTIONS PT-A HEAT/AC STANDARD KIT FORD E-SERIES VANS

INSTALLATION INSTRUCTIONS PT-A HEAT/AC STANDARD KIT FORD E-SERIES VANS INSTALLATION INSTRUCTIONS PT-A-402 - HEAT/AC STANDARD KIT 2007-2014 FORD E-SERIES VANS with Gas engine (To be used with 2007 and newer Prisoner Transport Inserts ONLY) Warning do not attempt to install

More information

Handshower, Hose & Handshower Accessories

Handshower, Hose & Handshower Accessories P24443, P24445, P24446, P24452, P24453, P24456 1 of 6 INSTALLATION INSTRUCTIONS Thank You For Choosing KALLISTA We appreciate your commitment to KALLISTA quality products. Please take a moment to review

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS Accessory Application Publication No. INSTALLATION INSTRUCTIONS GRIP HEATER ATTACHMENT P/N 08T70-MJL-D30 NC750X/XA/XD MII Issue Date November 2013 PARTS LIST GRIP HEATER Sold separately (6) (4) (5) (2)

More information

SERVICE INFORMATION BULLETIN

SERVICE INFORMATION BULLETIN Issue Date: 6-15-2009 Subject: Supply Pump Suction Control Valve Design Change J05D Engines Supersedes SB-07-006 dated 04-07-2008 (Revised 2-24-2009 to include 2010 model year vehicles) This bulletin provides

More information

SERVICE BULLETIN A

SERVICE BULLETIN A 1. PLANNING INFORMATION A. Effectivity: Dassault Falcon 10 aircraft which have installed R-134a Upgrade Kit SZ59K-R134 before August 8, 2002. B. Reason: Upgrade kits before August 8, 2002 did not include

More information

PERFECT FIT SERIES IN-DASH HEAT/ COOL/ DEFROST MUSTANG

PERFECT FIT SERIES IN-DASH HEAT/ COOL/ DEFROST MUSTANG specializing in AIR CONDITIONING, PARTS AND SYSTEMS for your classic vehicle PERFECT FIT SERIES IN-DASH HEAT/ COOL/ DEFROST 1965-66 MUSTANG CONTROL & OPERATING INSTRUCTIONS The controls on your new Perfect

More information

OPERATOR S MANUAL. For BURLY ATTACHMENTS

OPERATOR S MANUAL. For BURLY ATTACHMENTS OPERATOR S MANUAL For BURLY ATTACHMENTS April 4, 2018 Clod-Buster Topsoil Screener LIMITED WARRANTY Burly Attachments, LLC warrants to the original Purchaser, all products, manufactured by it, to be free

More information

General System Layout Sketch

General System Layout Sketch General System Layout Sketch EZ-37 Solar Panels PV panel Glycol Fill Valve Expansion Tank ` 1 Introduction This document describes how to install a Heliatos GH type solar water heating system. These systems

More information