Energize the crystal, summon the fire. USER MANUAL. Read carefully before using the device and save these instructions.

Transcription

1 Energize the crystal, summon the fire. USER MANUAL Read carefully before using the device and save these instructions.

2 USER MANUAL Table of Contents...Page 1. Introduction List of Components Getting Started Glass Water Filter Cleaning Tips Warranty Company Contact Information

3 Introduction Congratulations on purchasing your new Incendio TM kit! The Incendio TM is a portable e-nail that is powered by the revolutionary Firecore TM, a coil-less quartz heating element. Your material is vaporized without touching any coil, wick, or contaminated surface. This provides the cleanest hit possible with no contamination from the set up itself. Because of the smooth surface of the quartz glass, cleaning is a breeze. With a simple wipe from a cotton swab while the quartz is warm, your nail will be ready for the next dab. The Incendio TM comes with a battery featuring a dedicated e-nail setting. Simply adjust your desired temperature and activate the fire button. You can enjoy your session starting in 10 seconds. The kit includes a glass water filter along with a portable glass tank, making this a truly portable e-nail system. Some features of the kit: Incendio TM Tank Firecore TM Technology Glass Water Filter E-Nail Mode and VW Mode Powerful 5000mAh Li-ion Battery 2

4 Introduction Stainless Steel Carb Cap with Dab Tool Incendio TM Glass Water Filter Firecore TM Coil Atomizer Base Power Button LED Screen Incendio TM Battery Function Button Up Adjustment Button Down Adjustment Button 3

5 List of Components The Incendio TM kit comes with the following: 1 * Incendio TM Battery 1 * Stainless Steel Carb 1 * Incendio TM Tank Cap with Dab Tool (with installed Firecore TM Coil) 1 * USB Cable 1 * Incendio TM Glass 1 * Wax Container Water Filter 4

6 List of Components 1 * Spare Coil 3 * Spare Large 3 * Spare Small O-Rings O-Rings 5

7 Getting Started 1. Thread the Incendio TM Tank onto the 510-threaded connector on the battery. 2. Remove the glass chamber by twisting and pulling upwards. 6

8 Getting Started 3. Load the material into the heating bowl. (When using the tank, we recommend loading 0.1g 0.3g of material each time to get the best vaping experience). 4. Twist and press the glass chamber on to the base. 7

9 Getting Started 5. Press the power button 5 times quickly to turn on the battery. 6. To enter VW Mode, press and hold the function button until VW is displayed on the LED Screen. (We recommend using between 25W to 40W). 8

10 Getting Started 7. To adjust the wattage, use the up and down adjustment buttons until you have selected your preferred wattage. 8. Press and hold the power button to start vaping! 5.0 S WARNING: ENSURE THAT THE DEVICE IS OFF AND ATOMIZER BASE HAS COOLED BEFORE MAKING ANY ADJUSTMENT! MAY CAUSE BURNS OR SERIOUS INJURY IF HANDLED WHILE HOT! 9

11 Glass Water Filter 1. To use the Glass Water Filter, you will only need the atomizer base without the glass chamber. Thread the atomizer base onto the 510-threaded connector on the battery. 2. Max. limit of water level To fill the glass water filter, pour water from the top. Reverse the water filter upside down to pour out excessive water. When it is filled, the water level should not exceed the maximum level indicated in the photo. To remove the water, gently blow air through the mouthpiece while the filter is disconnected from the atomizer base and the battery. 10

12 Glass Water Filter 3. Connect the glass water filter by twisting and pressing it down gently onto the base of the atomizer. 11

13 Glass Water Filter 4. Press the power button 5 times quickly to turn on the battery. 5. Enter e-nail Mode on your device by pressing and holding the function button until e-nail is displayed on the LED screen Ω e-nail550 F 12

14 Glass Water Filter Ω e-nail600 F 0.40 Ω e-nail454 C To select the temperature, use the up and down adjustment buttons until preferred temperature is selected. (We recommend using between 600 o F to 850 o F.) 7. To begin the session, press and hold the power button for 2 seconds, after which the display will say Ready in about 10 seconds. 0.1 S 600 F 13

15 Glass Water Filter 8. Wait until the screen shows Ready in 10 seconds. Ready 9. Dab your material into the heated glass bowl while inhaling through the mouthpiece. Use the carb cap to adjust the air flow. 14

16 Glass Water Filter 10. After the material has melted into the Firecore TM, use the reverse side of the carb cap to control the airflow by pressing and releasing the two holes on the carb cap. 15

17 Cleaning Tips After you have completed your dab, use a cotton swab to clean out your glass bowl. To clean the water filter, pour half a cup of 90% alcohol into a cup, and pour the alcohol through the glass into the other cup. Repeat this process until the glass is cleaned and ready for your next dab! 90% Alcohol 16

18 Warranty Vivant Product Replacement This warranty provides free replacement of an authentic Vivant product if it malfunctions due to manufacturing defects. This warranty does not cover any damages outside of expected normal use. Void of Warranty Any one of the following conditions will void the warranty: 1. Failure to provide original receipt of purchase. 2. Product failure or damage due to improper use or unauthorized repair or alteration. 3. Product failure or damage due to the use of excessive force or user negligence (i.e. dropping the device, submerging the device in liquids, etc.). 4. Product failure or damage caused by using incompatible parts or wires (i.e. using the wrong power cable, etc.). Voiding the warranty is not limited to the conditions stated above. This warranty only covers authentic Vivant brand products and is valid for two years from the user s date of purchase. 17

19 Contact Information Vivant Inc Address: 3059 Edinger Ave, Tustin, CA 92780, USA Tel: vivant ( ) Web: 18