HAIR AND BEARD CLIPPER MC 8641

Transcription

1 HAIR AND BEARD CLIPPER MC 8641

2 D C A B E G F L H I J K O P M N Q 2 DEUTSCH

3 DEUTSCH 4-15 ENGLISH ESPAÑOL POLSKI ČESKY MAGYAR TÜRKÇE ΕΛΛΗΝΙΚA DEUTSCH 3

4 SAFETY Please note the following when starting up the appliance: 7 This appliance is intended for domestic use only. 7 To avoid damage and risks due to improper use, please read the instructions for use and store in a safe place. 7 When the mains adapter is connected, never use the appliance in the bath, shower or over a washbasin full of water or with wet hands. 7 If the appliance is charged or operated with the mains adapter, always ensure it does not come into contact with water or other liswuids. Even the proximity of water is a risk. 7 Always disconnect the mains adapter after charging. 7 Protect the mains adapter from water, especially dripping or splashing water. 7 Do not charge the appliance in the bathroom. 7 Make sure that the accessories are properly attached to prevent them falling into water. 7 Never fully immerse the appliance in water. 7 The appliance may only be allowed to come into contact with water if it is disconnected from the mains adapter and the mains adapter is no longer plugged into the socket. 7 Do not let the appliance fall. 7 Keep the appliance out of reach of children.. 16 ENGLISH

5 SAFETY 7 The device may not be used by the following people, including children: those with limited physical, sensory or mental capabilities and also those with a lack of experience and knowledge. This does not apply to the latter if they were instructed in the use of the device or if they use it under the supervision of a person responsible for safety. Children should always be supervised to ensure that they do not play with the device. 7 If the power cord is damaged, it must be replaced by the manufacturer, its service centre or a similarly qualified person to prevent danger arising. 7 Never open up the appliance. All rights to claim under the guarantee are invalidated for damage caused by improper interventions ENGLISH 17

6 AT A GLANCE See the illustration on page 2. Accessories Controls A B C D E F G Slide switch for switching on and off, switches to two speed settings. Switch for adjusting the comb attachment position or removing the comb attachment, rear of the appliance. Indicator for the comb attachment positions, rear of appliance. Ceramic/stainless steel cutting head (trimming width 40 mm). LED indicator for charging. Socket for docking into the charging station or connecting the mains adapter. Charging station. H I J K L M N O P Q Comb attachment 1 for shorter hair lengths (up to 20 mm). Comb attachment 2 for longer hair lengths (from 24 mm to 40 mm). Stainless steel cutting head for trimming beards (trimming width 25 mm). Beard attachment trimming lengths of 2 mm to 18 mm Power supply unit. Storage case. Attachment for thinning out hair. Cleaning brush. Oil. Comb. 18 ENGLISH

7 POWER SUPPLY Runs on rechargeable batteries If run with the installed rechargeable nickel metal hydride batteries, use the supplied mains adapter as a charger. 1 Insert the mains adapter cable into the socket F ; plug the mains adapter plug into the mains socket. The indicator E lights up. Note 7 Fully charge the batteries (24 hours) before using for the first time or if the batteries have not been used for a long time. 7 After the batteries are first charged, the charging time is approx. 12 hours when the appliance is switched off. If you switch on the appliance while it is charging, charging will stop. 7 The ambient temperature should be between 5 C and 40 C. 7 When fully charged, the appliance works for around 45 minutes. It is not advisable to charge the batteries after every use, especially if you do not use the appliance for the full 30 minutes. Only charge the batteries when they are completely discharged. This increases their life. Do not charge them every day. Charge at the charging station 1 Push the appliance's socket F onto the charging station connector. 2 Insert the cable of the mains adapter into the socket of the charging station. 3 Plug the mains adapter plug into the mains socket. ENGLISH 19

8 POWER SUPPLY Mains operation (with the mains adapter) Check whether the mains voltage given on the rating plate of the mains adapter supplied matches the local mains voltage. The appliance is not disconnected from the power supply until the mains adapter is disconnected. 1 Insert the cable of the mains adapter into the socket F. 2 Plug the mains adapter plug into the mains socket. The installed batteries are switched off. Important 7 If using the appliance in the bathroom or next to a water connection, use battery (cordless) mode only and never use mains mode. Environmental information This product has been made from high-quality materials and parts, which are suitable for recycling and can be reused. Therefore, at the end of its life, the product must not be disposed of in the normal domestic waste but must be taken to a collection point for recycling electrical and electronic appliances. This is indicated by the following symbol on the product, in the instructions for use or on the packaging. Please contact your local authority to find out where your local collection points are. Reusing and recycling old appliances is an important contribution to protecting our environment 20 ENGLISH

9 USE Special features The appliance is equipped with a ceramic/stainless steel blade. Cut hair 1 Push on the comb attachment H or I. Important 7 Before attaching the comb attachment, always switch off the appliance first and if necessary disconnect the mains adapter cable. 2 To do this, push the side guide grooves inside the comb attachment onto the side guide rails of the appliance until the attachment latches into position. 3 Press down the switch B and set the required cutting length (from 1 to 7) (see the following tables). Note the indicator C for the comb attachment positions. 4 Place a hand towel around the neck and shoulders of the person whose hair is to be cut. Seat the person so that their head is roughly at your eye level. Before cutting, comb the hair so that it falls loosely and you can see the natural growth direction. 5 Switch on the appliance using the switch A and start to cut the hair. 6 If necessary, use the switch A to set the required speed setting (1 or 2). Note 7 Speed setting 2 is a switchable turbo setting for more power for thick and long hair. 7 After cutting the hair, switch A off the appliance at the switch (setting 0). 8 Remove the comb attachment by pressing the switch B and pulling off the comb attachment. ENGLISH 21

10 USE Cutting lengths of comb attachment 1 ( H ) Position 1 Position 2 Position 3 Position 4 Position 5 Position 6 Position 7 Cutting lengths of comb attachment 2 ( I ) Position 1 Position 2 Position 3 Position 4 Position 5 Position 6 Position 7 4 mm 7 mm 9 mm 12 mm 15 mm 17 mm 20 mm 24 mm 27 mm 29 mm 32 mm 35 mm 37 mm 40 mm Notes 7 If you use the appliance without the comb attachment, the cutting length is 1.5 mm. 7 The cutting lengths given are the remaining hair lengths after cutting. All the measurements given here are approximate values. Useful tips 7 Use the appliance with a relaxed and comfortable grip. 7 Always cut against the natural direction of hair growth. 7 Pause cutting at short intervals. You can always make corrections later, but you can't replace cut hair. 7 When using for the first time, cut small amounts of hair only. This enables you to get used to the adjustable cutting lengths. 7 Do not force the comb attachment through the hair. Let it lead you. 7 Comb the hair repeatedly. While combing, look for hair that is too long and remove cut hair. 7 Use the N attachment for thinning out hair. Insert it from above, as you did for comb attachment 1, into the side grooves until it catches. 22 ENGLISH

11 USE Beard trimming 1 Press the A button to switch off the appliance (level 0). 2 Remove the hair comb by pressing the B button and taking it off. 3 Remove the cutting head for hair and replace it with the cutting head for the beard J. 4 Put the beard comb K on. 5 Slide the comb with the inner side grooves onto the side guide rails on the appliance. 6 Press the switch B down and set the cutting length (from 1 to 7) (see the following table). Observe the display C for the comb positions. 7 Switch on the appliance with the A button and start trimming the beard. 8 If required, set the speed to level 2 with the A button. Note 7 Speed level 2 is a turbo level with extra power for strong beard hair. Trimming lengths of the beard comb ( K ) Position 1 Position 2 Position 3 Position 4 Position 5 Position 6 Position 7 2 mm 5 mm 7 mm 10 mm 13 mm 15 mm 18 mm Notes 7 If you use the appliance without the beard attachment, the cutting length is 1.5 mm. 7 The trim lengths given here describe the remaining hair length. All the lengths here are approximate. ENGLISH 23

12 CLEANING AND CARE Cleaning and care 1 Switch off the appliance and, if using in mains mode, remove the mains adapter plug from the socket. 2 Remove the comb attachment and clean the blade with the supplied brush. 3 Clean the housing and comb attachment with a soft cloth moistened with water. Important 7 Never hold the appliance, cable or mains adapter in water or any other liquid. 4 Before using again, ensure all parts have been carefully dried with a soft cloth. 5 Do not use cleaning agents. 6 Re-attach the comb attachment. Notes 7 Remove any remaining hair after each use. 7 Your appliance's comb attachment does not usually need oiling. If you want to retain the original condition of the blade for a long time, it is worthwhile oiling the blade at regular intervals using the oil supplied. Storage If you are not going to be using the appliance for a lengthy time, please store it carefully. 7 Ensure the appliance is switched off and is completely dry. 7 Pack the parts in the original packaging and store them in a cool, dry place. 7 Ensure the appliance is kept out of reach of children. 24 ENGLISH

13 INFORMATION Guarantee The guarantee does not include the blade or defects, which have an insignificant effect on the appliance's value or fitness for use. The guarantee is invalidated if the appliance is damaged, opened or improperly used. Technical specifications This product fulfils the European Directives 2004/108/EG and 2006/95/EG. Power supply Rechargeable battery: Nickel metal hydride 900 ma Power supply unit: V, 50/60 Hz 3.4 V DC 1000 ma Weight (WEEE) 520 g Ni-MH Subject to technical and visual changes! ENGLISH 25