APPROVAL SHEET S PE CIFICATIONS OF HE R ME TIC S CR OLL COMPR E S S OR CODE MODE L C-S B353H8A

Transcription

1 Dirección: Scalabrini Ortiz 1375, Bs. As. Teléfonos: /6006/ No. : J S GGS Y-06 APPROVAL SHEET S PE CIFICATIONS OF HE R ME TIC S CR OLL COMPR E S S OR CODE MODE L C-S B353H8A NO. DATE PAGE REVISION DETAILS S ANYO S IGNE D CLIE NT S IGNE D REVISION RECORD USER : MANUFAC TUR E R : DALIAN SANYO COMPRESSOR CO., LTD. LEADER PURCHASING MANAGE R TECHNICAL MANAGE R APPROVED CHECKED SUBMITTED 1

2 Section 1. General Specifications 2

3 Section 2. Perform ance W arranty 2.1 Perform ance Standard Rating Conditions 2.2 Sound Level 2.3 Minim um Starting Voltage Conditions 2.4 Others 3

4 Section 3. Standard Accessories 3.1 Accessories List Parts Name Qty Parts code Revision No. Note TerminalBox Cover 1 A-0101-DSB 0 Insta led on Compressor TerminalBox Clip 1 A-0201-DSB 0 Insta led on Compressor Insulating Grommet 1 A-0301-DSB 0 Insta led on Compressor Mounting Grommet 4 M-0101-DSB 0 Included with Compressor Mounting Sleeve 4 M-0201-DSB 0 Included with Compressor Screw Special 1 B-0101-DSB 0 Insta led on Compressor 3.2 The Drawing for Reference Parts Name Compressor Outline Drawing Mounting Parts Listing Packing Dimensions Nameplate W iring Diagram Parts Code D-0101-DSB M-5101-DSB D-0201-DSB A-5106-DSB E-0910-DSB Revision No Inernal Moter Protector (in compressor) Parts Name Specification InernalMotor Protector Trip Temprature Reset Temprature Trip Current 145±5 61±9 47A /2~10s 4

5 Section 4. Compressor Protection 4.1 Protection Required but not Included with compressor Position of the Protection and Refrigerant Charging 5

6 Section 5. Operating Envelope Suction Gas Superheat 11.1K Refrigerant R22 Condensing Temperature Evaporating Temperature 6

7

8 Notes 1 Installation should be completed within 15 minutes after removing the rubber plugs. 2 Do not use the compressor to compress air. 3 Do not energize the compressor under vacuumed conditon. 4 Liquid refrigerant should be charged on liquid line between condenser and receiver. Do not charge the liquid refrigerant on the suction or discharge pipe of the compressor. 5 Do not tilt over the compressor while carrying it. 6 Do not remove the paint. 7 Crankcase heater is required when the oil sump temperature is too low to meet the requirement of item 6 on page7. 8 Voltage fluctuation between compressor terminals,during operation,shall be within 2% of the rated voltage. 9 Do not operate compressor in reverse rotational direction. 10 Suction strainers are recommended for all applications. 8

9

10 No. Part Code Qty Name Compressor 2 A-0101-DSB 1 Terminal Box Cover 3 A-0201-DSB 1 Terminal Box Clip 4 A-0301-DSB 1 Insulating Grommet 5 A-5102-DSB 1 Nameplate 6 B-0101-DSB 1 Screw Special 10 U V W Part Code D-0101-DSB Name Compressor Outline Drawing

11

12 ` 1125 [44.291] [45.197] 1160 [45.669] 1086 [42.756] [ ] 410 [2.362] 60 [2.362] 90[3.543] 60 [2.362] 410 [2.362] 60 [2.362] [ ] Part Code D-0201-DSB Name Packing Dimensions

13 C-SB353H 8A 3W 13 Part Code A-5106-DSB Name Nameplate

14 SWITCH V POWER SUPPLY 50Hz 380~415V R S T U INTERNAL PROTECTOR W MAGNETIC SWITCH COMPRESSOR R C 14 POWER SUPPLY 50Hz 220V S T REVERSAL DEFENSIBLE RELAY B A CRANKCASE HEATER Part Code E-0910-DSB Name W iring Diagram