CME1856W Service Parts

Transcription

1 This parts list contains the part numbers and description of the replacement parts available for this model. To avoid costly and time consuming errors, double check the model and voltage before ordering a part. TABLE OF CONTENTS Cabinet PAGE Water System PAGE Refrigeration PAGE Electrical PAGE 5 BH00 Ice Storage Bin PAGE 6 BH650 Ice Storage Bin PAGE 7 Kit Parts PAGE 8 Single Phase Wiring Diagram PAGE Single Phase Schematic Diagram PAGE 0 Three Phase Wiring Diagram PAGE Three Phase Schematic PAGE November 00 Page

2 Cabinet Top panel, plastic Insulation A Back panel Screw 5 A Right side panel, SS 6 A7-00 Right bottom channel 7 A7-00 Right side support Evaporator cover & ins Cover retainer CM emblem Emblem Panel support clip Front panel screw A78-0 Front panel, SS, includes items and 5 A75-00 Channel, front top 6 A78-00 Left side panel, SS 7 A Left side channel Left grommet A76-00 Bracket Right grommet Screw A70-00 Control box cover July 008 Page

3 Water System Elbow Hose clamp O-ring Manifold Manifold right Plug Water distributor 8 A75-0 Evaporator Ice deflector Right trough Left trough A77-00 Evap support Ice sensor (set) Ice sensor holder Upper inner splash panel 5 6 " " Tube, order unit Lower inner splash panel Water discharge hose Temp sensor set Float stem Drain hose, order units Purge valve Drain plug 0-6- Drain fitting Float Pump bracket Water level sensor Water solenoid valve Coupling half Harness for water sensor Pump bracket -58- Water pump A70-00 Bracket Screw Nylon screw Reservoir cover August 008 Page

4 OUTLET CME856W Service Parts Refrigeration INLET 0 6 EVAPORATOR SECTION a 6a Water cooled condenser Receiver Hot gas header Low pressure cut out 5 A Distributor and tubes Suction manifold Accumulator 7a A70-00 Accumulator bracket Strainer for HGV A88-00 Drain fitting Hot gas valve w/coil -7- Hot gas valve coil only A75-0 Evaporator 6-0- TXV, AAE 5Z Insulation for TXV Temp sensor set Hi pressure cut out Suction access valve Port cap Stem cap Solid Mount Rubber grommet 6a Rubber pad for sold mount Bolt 7a Washer for solid mount Washer for rubber grommet Sleeve for rubber grommet Compressor, 60 Hz, single phase Compressor, 60 Hz, phase crankcase heater for phase Replacement compressors include a dryer 0--0 Dryer Water reg valve April 00 Page

5 a CME856W Service Parts PH ONLY Electrical 0 PH ONLY 7 8 PH ONLY 6 PH ONLY 5 V (/6) TOWARD FRONT OF MACHINE 5 PH ONLY A77-00 Transformer -- Snap bushing --0 Snap bushing Screw Hz potential relay Run capacitor Hz start capacitor 8 A Strap -88- Controller Single phase contactor -05- Purge valve timer Stand off -5-0 phase contactor Time delay relay a Screw Bin thermo harness Bin thermostat Not Shown: Thermostat bracket pronged knob Lo voltage harness -7-0 Hi voltage harness April 00 Page 5

6 BH00 Ice Storage Bin 0 a b ITEM PARTS NUMBER NUMBER DESCRIPTION A5-00 Canopy Assembly A55-00 Ice Baffle Drain Top O-ring Drain casting 6 KLPE Leg Kit, Black KLPS Leg Kit, Nickel Plated Emblem Door gasket (6.5 reg.) Bin gasket / ft Baffle screw A Door frame assy. A76-0 Door frame, BH00S-C ITEM PARTS NUMBER NUMBER DESCRIPTION A5-00 Door w/gasket - BH E ring Hinge bushing Door hinge Bin hinge Shoulder screw Spacer 0-0- Screw Screw 0- A Left bin channel a A5-00 Back bin channel b A57-00 Right bin channel Trim guard April 00 Page 6

7 BH650 Ice Storage Bin Z Brackets are used when attaching CME56 or CME656 to bin. Attaching screw pn: Gasket: , order number of feet needed Track Window Lower frame assembly Left and right hinges Door with door hinges Right hinge Ice gate End plate guide (pair) Screws for end plat Plugs for end plate Catch for ice gate November 00 Page Ice gate retainer Left hinge Plastic drain 5 KLPS Legs Not Illustrated: Probe tool Plastic Ice shovel Z brackets

8 Stacking Kit,KSCME6-LG-B CME856W Service Parts Kit Parts A Harness: -6-0 November 00 Page 8

9 Single Phase Wiring Diagram November 00 Page

10 Single Phase Schematic Diagram November 00 Page 0

11 Three Phase Wiring Diagram November 00 Page

12 Three Phase Schematic November 00 Page

13 Bulletin Number: PS Bulletin Date: April 00 SERVICE BULLETIN Subject: Controller Cover Affects all versions of models: CME56, CME656, CME856 and CME006 The above models are now manufactured with a sheet metal cover over the top of the controller. Service controllers also are now shipped with a cover that should be applied to these models whenever replacing the controller if the machine does not already have a cover installed. Whenever cleaning or servicing any unit, check to see whether it has a cover over the controller like the one shown below. If it does not, Scotsman recommends installing a cover. A separate part is now available for this purpose. Its part number is A It mounts over the top end of the controller and is secured by two sheet metal screws. Use the cover as a template and drill two /8 holes for the two screws. Controller Cover Cover Installed on Unit Scotsman is shipping a supply of covers to all Scotsman Distributors and listed service agencies. A supply of covers should be carried by each service person on service calls so a cover may be installed on the unit being cleaned or serviced if one is not already in place. Additional covers may be obtained free of charge from Scotsman, through the local Scotsman Distributor, as needed.