Product Data. 38CKC 50 Hz Air Conditioner. Sizes 018 thru 060 FEATURES

Transcription

1 Product Data 38CKC 50 Hz Air Conditioner Sizes 018 thru 060 Model 38CKC 50 Hertz energyefficient air conditioner incorporates innovative technology to provide reliable summer cooling performance. Built into these units are the features most desired by customers today, including EER ratings of up to 9.5 when used with components designated by manufacturer. FEATURES Electrical Range Single phase units are available in 018, 024, 030, and 036 sizes in 230v. Three-phase units are available in 036, 042, 048, and 060 sizes in 400v. Wide Range of Sizes The 38CKC is available in nominal sizes 018, 024, 030, 036, 042, 048, and 060 to meet the needs of residential and light commercial applications. Weather Armor II Cabinet A weather protective cabinet of prepainted steel is protected underneath by a zinc galvanized coating for a finish that will last for many years. All screws on cabinet exterior are coated for a long-lasting, rust-resistant, quality appearance. Totally Enclosed Fan Motor Means greater reliability under adverse weather conditions and dependable performance for many years. The permanent-split-capacitor type motor was designed for optimum efficiency. The motor was tested and qualified under extreme conditions to ensure the greatest reliability. Copyright 2005 Carrier Corporation Form 38CKC-C7PD

2 Unit Design Copper tube, epoxy coated, enhanced sine wave aluminum fin coil is designed for optimum heat transfer and corrosion protection. Vertical air discharge carries sound and hot condenser air up and away from adjacent patio areas and foliage. Heat pump style drain pan allows for easy removal of water, dirt, and leaves. Application Versatility The unit can be combined with a wide variety of evaporator coils and blower packages to provide quiet, dependable comfort. Unit can be installed on a roof or at ground level. External Service Valves Both service valves are brass, front seating type. The 38CKC has sweat field connections. Valves are externally located so refrigerant tube connections can be made quickly and easily. Each valve has a service port for ease of checking operating refrigerant pressures. Easy Serviceability One access panel provides access to electrical controls and compressor. Removal of wire dome gives access to fan motor and removal of the top gives access to the coil. Pressure Switches All units are equipped with high and low pressure switches. Additional Compressor Protection Each compressor is protected with internal temperatureand current-sensitive overloads. Sound Hood 38CKC Sizes 036 through 060 have a compressor sound hood for noise attenuation. 3-Phase Monitor Board Control board that monitors the electrical phase and prevents operation if wired incorrectly. The board is standard on the 048 and phase equipment. Operating Range Minimum outdoor operating ambient in cooling mode is 55ºF (12.8ºC), maximum 125ºF (51.7ºC). Quality Assurance ISO 9001:2000 REGISTERED REGISTERED QUALITY SYSTEM Model number nomenclature 38CKC A 3 Electric Air Conditioner Nominal Capacity ,000 Btuh (5.3 kw) ,000 Btuh (12.3 kw) ,000 Btuh (7.0 kw) ,000 Btuh (14.1 kw) ,000 Btuh (8.8 kw) ,000 Btuh (17.6 kw) ,000 Btuh (10.6 kw) Series Electrical Packaging The data in this publication is displayed for all series, however, every series may not be available from manufacturer. 2

3 Physical data UNIT SIZE / SERIES 018-7A 024-7A 030-7A 036-7A, 9A 042-9A 048-7A, 9A 060-9A OPERATING WT (Lb/Kg) 120 / / / / / / / 99.5 COMPRESSOR Type Recip Recip Recip Recip Scroll Scroll Scroll REFRIGERANT Control Charge 15 ft / 4.6m COND FAN Air Discharge Air Qty (CFM / L/S) R-22 AccuRater 3.76 / / / / / / /4.13 Propeller Type, Direct Drive Vertical 1600 / / / 1510 COND COIL Face Area (Sq ft / m2) 6.2 / / / / / / / 2.06 VALVE CONNECT. (In./mm ID) Vapor Liquid REFRIG TUBES* (In./mm OD) Vapor Liquid Sweat 5/8 / /4 / /4 / /8 / /8 / /8 / /4 / /4 / /8 / /8 / /8 / 9.53 * Tube sizes are for runs up to 50 ft (15.24m). For tube set over 50 ft (15.24m), consult Residential Split-System Long-Line Application Guideline. NOTE: See unit Installation Instructions for proper installation. ACCURATER PISTON CHART PISTON UNIT SIZE IDENTIFICATION NO.* 018-7A A A A, 9A A A, 9A A 98 * Piston listed is for any approved non-capillary tube coil combination. Piston is shipped with outdoor unit and must be installed in an approved indoor coil. 3

4 Accessories PART NO. DESCRIPTION KSAHS1001AAA Start Assist Capacitor/Relay Sizes 018, 024 KSAHS1301AAA Start Assist Capacitor/Relay Size 030, 036 (7A) KSAHS1601AAA Start Assist Capacitor/Relay Size 048 (7A) KAACS0101PTC Start Assist PTC Sizes 018, 024 KAACS0201PTC Start Assist PTC Sizes 030, 036, 048 (7A) KAALS0101LLS* Liquid Solenoid Valve All Sizes KSACY0101AAA Cycle Protector All Sizes KAAWS0101AAA Winter Start Control All Sizes KAAFT0101AAA Evaporator Freeze Thermostat All Sizes KAATD0101TDR Time-Delay Relay All Sizes KSASF0101AAA Support Feet All Sizes KAACH1001AAA Crankcase Heater Sizes 018, 024, 030, 036 (7A) KAACH1101AAA Crankcase Heater Sizes 036 (9A) KAACH1201AAA Crankcase Heater Size 048 (7A) KAACH1301AAA Crankcase Heater Sizes 042, 048 (9A), 060 KAACF0701SML Coastal Filter Size 018 KAACF1001MED Coastal Filter Sizes 024, 030, 036 KAACF1101LRG Coastal Filter Sizes 042, 048, 060 KAATX0201RPB Thermostatic Expansion Valve (RPB) Size 018 KAATX0301RPB Thermostatic Expansion Valve (RPB) Size 024 KAATX0401RPB Thermostatic Expansion Valve (RPB) Size 030 KAATX0501RPB Thermostatic Expansion Valve (RPB) Size 036, 042 KAATX0601RPB Thermostatic Expansion Valve (RPB) Size 048 KAATX0701RPB Thermostatic Expansion Valve (RPB) Size 060 KSATX0601HSO* Thermostatic Expansion Valve (Hard Shutoff) Sizes 018, 024, 030, 036, 042 KSATX0701HSO* Thermostatic Expansion Valve (Hard Shutoff) Size 048 KSATX1001HSO* Thermostatic Expansion Valve (Hard Shutoff) Size 060 KSALA0201R22 Low-Ambient Pressure Switch (R22) All Sizes KSALA0401AAA MotorMaster Control 024, 030, 036 (7A), 048 (7A) KSALA0501AAA MotorMaster Control 036 (9A), 042, 048 (9A), 060 KH45LD060 Filter Drier KH45LE062 Filter Drier 048, 060 * Do not use hard shutoff TXV with liquid solenoid valve. THERMOSTAT TSTATCCNAC01-C TSTATCCPAC01-B TSTATCCBAC01-B TSTATCCPRH01-B TSTATCCSAC01 TSTATXXSEN01-B TSTATXXNBP01 TSTATXXPBP01 TSTATXXBBP01 TSTATXXSBP01 TSTATXXCNV10 DESCRIPTION Thermostat, Auto Changeover, Non-Programmable, F/ C, 1-Stage Heat, 1-Stage Cool Thermostat, Auto Changeover, 7-Day Programmable, F/ C, 1-Stage Heat, 1-Stage Cool Builder s Thermostat, Manual Changeover, Non-Programmable, F/ C, 1-Stage Heat, 1-Stage Cool Thermidistat, Programmable/Non-Programmable Thermostat with Humidity Control Thermostat, Manual Changeover, 5-2 Day Programmable, F/ C, 1-Stage Heat/1-Stage Cool, 50/60 Hz, 24 Vac Outdoor Air Temperature Sensor Backplate for Non-Programmable Thermostat Backplate for Programmable Thermostat Backplate for Builder s Thermostat Backplate for Standard Programmable Thermostat Thermostat Conversion Kit (4 to 5 Wire) 10 Pack 4

5 Accessory usage guideline ACCESSORY REQUIRED FOR LOW-AMBIENT APPLICATIONS (Below 55 F) (12.8 C) REQUIRED FOR LONG-LINE APPLICATIONS* (Over 50 Ft) (15.24m) REQUIRED FOR SEA COAST APPLICATIONS (Within 2 Mi) (3.2km) Crankcase Heater Yes Yes No Evaporator Freeze Thermostat Yes No No Winter Start Control Yes No No Accumulator No No No Compressor Start Assist Capacitor and Relay Yes Yes No Low Ambient Controller or MotorMaster Control Yes No No Wind Baffle See low-ambient Instructions Coastal Filter No No Yes Support Feet Recommended No Recommended Liquid-Line Solenoid Valve or Hard Shutoff TXV No * For tubing line sets between 50 (15.24m) and 175 ft (53.34m), refer to Residential Split System Long-Line Application Guideline. Only when low-pressure switch is used. Accessory description and usage (Listed alphabetically) 1. Coastal Filter A mesh screen inserted under the top cover and inside the base pan to protect the condenser coil from salt damage without restricting airflow. SUGGESTED USE: In geographic areas where salt damage could occur. 2. Compressor Start Assist Capacitor/Relay Type Start capacitor and start relay gives hard boost to compressor motor at each start-up. SUGGESTED USE: Installations where interconnecting tube length exceeds 50 ft (15.24m). Installations where outdoor design temperature exceeds 105 F (40.6 C). Replacement installations with hard shutoff expansion valve on indoor coil. 3. Compressor Start Assist PTC Type Solid-state electrical device which gives a soft boost to the compressor at each start-up. SUGGESTED USE: Installations with marginal power supply. Replacement installations with rapid pressure balance (RPB) expansion valve on indoor coil. 4. Crankcase Heater An electric resistance heater which mounts to the base of the compressor to keep the lubricant warm during off cycles. Improves compressor lubrication on restart and minimizes chance of refrigerant slugging. May or may not include a thermostat control. SUGGESTED USE: When interconnecting tube length exceeds 50 ft (15.24m). When unit will be operated below 55 F (12.8 C) outdoor air temperature. (Use with low-ambient controller.) All commercial installations. 5. Cycle Protector Solid-state timing device which prevents compressor rapid recycling. Control provides an approximate 5-minute delay after power to the compressor has been interrupted for any reason, including normal room thermostat cycling. SUGGESTED USE: Installations in areas where power interruptions are frequent. Where user is likely to play with the room thermostat. All commercial installations. Installations where interconnecting tube length exceeds 50 ft (15.24m). High-rise applications. 6. Evaporator Freeze Thermostat A SPST temperature actuated switch which stops unit operation when evaporator reaches freeze-up conditions. SUGGESTED USE: All units where winter start control has been added. 7. Liquid Solenoid Valve (LSV) An electrically operated shutoff valve to be installed at the outdoor or indoor unit (depending on tubing configuration) which stops and starts refrigerant liquid flow in response to compressor operation. Maintains a column of refrigerant liquid ready for action at next compressor operation cycle. NOTE: Compressor start assist capacitor/relay type must also be used. SUGGESTED USE: For improved system performance in air conditioners for certain combinations of indoor and outdoor units. (Refer to ARI Unitary Directory.) In certain long-line applications. Refer to Residential Split System Long-Line Application Guideline. 8. Low-Ambient Pressure Switch A long-life pressure switch that maintains head pressure by turning the fan OFF and ON. SUGGESTED USE: operation at outdoor temperatures below 55 F. All commercial applications. 9. MotorMaster Control A fan speed control device activated by a temperature sensor.designed to control condenser fan motor speed n response to the saturated, condensing temperature during operation in cooling mode only. For outdoor temperatures down to 20 F ( 28.9 C), it maintains condensing temperature at 100 F±10 F (37.8 C ± 12.2 C). SUGGESTED USE: operation at outdoor temperatures below 55 F (12.8 C). All commercial installations. 10. Support Feet Four stick-on plastic feet which raise the unit 4 in. (10.16cm) above the mounting pad. This allows sand, dirt, and other debris to be flushed from the unit base; minimizes corrosion SUGGESTED USE: Coastal installations. Windy areas or where debris is normally circulating. Rooftop installations. No See Long-Line Application Guideline No No 5

6 Accessory description and usage (Listed alphabetically) continued 11. Thermostatic Expansion Valve (TXV) A modulating flow-control valve which meters refrigerant liquid flow rate into the evaporator in response to the superheat of the refrigerant gas leaving the evaporator. Kit includes valve, adapter tubes, and external equalizer tube. Both hard shutoff and RPB valves are available. SUGGESTED USE: For improved system performance in cooling mode for certain combinations of indoor and outdoor units. Refer to ARI Unitary Directory. 12. Time-Delay Relay A SPST delay relay which briefly continues operation of the indoor blower motor to provide additional cooling after the compressor cycles off. SUGGESTED USE: For improved efficiency ratings for certain combinations of indoor and outdoor units. Refer to ARI Unitary Directory. 13. Winter Start Control A SPST delay relay which bypasses the low-pressure switch for approximately 3 minutes to permit start-up for cooling operation under low-load conditions. SUGGESTED USE: All air conditioners where low-ambient controller has been added. Electrical data UNIT SIZE-SERIES V/PH OPER VOLTS* COMPRESSOR Max Min LRA RLA 018-7A / / A / / A / / A / / A /10 91/ / A / / A / / A / / A / /44 20 * Permissible limits of the voltage range at which unit will operate satisfactorily. Operation outside these limits may result in unit failure. Time-delay fuse. Length shown is as measured 1 way along wire path between the unit and service panel for a voltage drop not to exceed 2%. ** If wire is applied at ambient greater than 30 C (86 F), consult Table of the NEC (ANSI/NFPA 70). The ampacity of nonmetallic-sheathed cable (NM), trade name ROMEX, shall be that of 60 C (140 F) conductors, per the NEC (ANSI/NFPA 70) Article If other than uncoated (non-plated), 60 or 75 C (140 or 167 F) insulation, copper wire (solid wire for 10 AWG and smaller, stranded wire for larger than 10 AWG) is used, consult applicable tables of the NEC (ANSI/NFPA 70). FLA Full Load Amps LRA Locked Rotor Amps MCA Minimum Circuit Amps RLA Rated Load Amps NOTES: 1. Control circuit is 24v on all units and requires external power source. 2. Copper wire must be used from service disconnect to unit. 3. All motors/compressors contain internal overload protection. FAN FLA MCA MIN WIRE SIZE 60 C/75 C** MAX LENGTH (Ft) 60 C/75 C MAX LENGTH (m) 60 C/75 C MAX FUSE OR CKT BKR AMPS 6

7 Dimensions A SQ AIR DISCHARGE M AIR IN AIR DISCHARGE AIR IN 3/8 IN. (9.5mm) DIA TIEDOWN KNOCKOUTS (2) PLACES N J K L AIR IN B FIELD POWER SUPPLY CONN 7 /8 IN. (22.2mm) DIA HOLE WITH 1 1 /8 IN. (28.6mm) DIA KNOCKOUT AND 1 3 /8 IN. (34.9mm) DIA KNOCKOUT FIELD CONTROL SUPPLY CONN 7 /8 IN. (22.2mm) DIA HOLE 3/8 IN. (9.5mm) DIA LIQUID LINE CONN P AIR DISCHARGE E F AIR IN G H D DIA VAPOR LINE CONN 1 1 /4 (31.8mm) 2 7 /8 (73.0mm) C S.I. UNIT SIZE MINIMUM MOUNTING PAD DIMENSIONS (mm) MINUMUM MOUNTING PAD DIMENSIONS (In.) x x , 030, 036, x /2 x 22 1/2 048, x x 30 NOTES: 1. Allow 30 In. (762.0mm) clearance to service side of unit, 48 In. (1219.2mm) above unit, 6 In. (152.4mm) on one side, 12 In. (308.8mm) on remaining side, and 24In. (609.6mm) between units for proper airflow. 2. Minimum outdoor operating abient in cooing mode is 55 F(13 C), max 125 F(52 C). 3. Series designation is the 13th position of the unit model number. 4. Center of gravity. A97007 A B C D E F G H J K L M N P UNIT SERIES mm mm mm mm mm mm mm mm mm mm mm mm mm mm kg 38CKC018 A CKC024 A CKC030 A CKC036 A CKC042 A CKC048 A CKC060 A ENGLISH SHIPPING WEIGHT A B C D E F G H J K L M N P UNIT SERIES In. In. In. In. In. In. In. In. In. In. In. In. In. In. Lb. 38CKC018 A /16 3-3/16 5/ / /4 10-3/ /8 17-9/16 7-7/8 8-3/8 10-1/ CKC024 A 22-1/ /16 3-3/16 5/8 3-11/ /8 19-3/4 22-1/4 14-3/8 19-9/ / /8 10-1/4 10-3/ CKC030 A 22-1/ /16 3-3/16 3/4 3-11/ /8 19-3/4 22-1/4 14-3/8 19-9/ / /8 10-1/4 10-3/ CKC036 A 22 1/ /16 3-3/16 3/4 3-11/ /8 19-3/4 22-1/4 14-3/8 19-9/ / /8 10-3/4 10-3/ CKC042 A 22-1/ /16 3-1/4 7/8 3-11/ /8 19-3/4 22-1/4 14-3/8 19-9/ / /8 10-3/4 10-3/ CKC048 A /16 3-1/4 7/8 6-1/2 23-1/2 27-1/4 29-3/ / / / CKB060 A /16 3-1/4 7/8 6-1/2 23-1/2 27-1/4 29-3/ / / /2 14-3/ SHIPPING WEIGHT 7

8 Combination ratings* COOLING 95 F (35 C) COOLING CAP@115 F (46 C) OUTDOOR UNIT NOMINAL AIRFLOW Rated Capacity Rated Rated Capacity SIZE-SERIES INDOOR UNIT CFM L/S BTUH kw kw EER BTUH kw kw 018-7A FB4BSF018 FB4BSF A FB4BSF024 FB4BSF A FB4BSF030 FB4BSF A, 9A FB4BSF036 FB4BS(F,B) A FB4BS(F,B)042 FB4BS(F,B) A, 9A FB4BS(F,B)048 FB4BS(F,B) A FB4BS(F,B)060 FB4BSF * Ratings are net values reflecting the effects of circulating fan heat. Supplemental electric heat is not included. Ratings are based on: Standard: 80 F (27 C) db 67 F (19 C) wb indoor entering air temperature and 95 F (35 C) db air entering outdoor unit. A-weighted sound power (dba) UNIT SOUND RATING TYPICAL OCTAVE BAND SPECTRUM (WITHOUT TONE ADJUSTMENT) (Hz) SIZE (dba) A A A A A A A, 9A A

9 Detailed cooling capacities* (S.I.) L/S EVAP AIR (C) EWB See notes on pg. 11. CONDENSER ENTERING AIR TEMPERATURES C (kw) Sys. (kw) Sys. (kw) Sys. (kw) Sys. (kw) Sys. (kw) Sys. Total Sens kw** Total Sens kw** Total Sens kw** Total Sens kw** Total Sens kw** Total Sens kw** 38CKC018-7A Outdoor With FB4BSF Multipliers for Determining the Performance With Other s Size Capacity Size Capacity FB4BSF CKC024-7A Outdoor With FB4BSF Multipliers for Determining the Performance With Other s Size Capacity Size Capacity FB4BSF CKC030-7A Outdoor With FB4BSF Multipliers for Determining the Performance With Other s Size Capacity Size Capacity FB4BSF

10 Detailed cooling capacities* (S.I.) L/S EVAP AIR (C) EWB See notes on pg. 11. CONDENSER ENTERING AIR TEMPERATURES C (kw) Sys. (kw) Sys. (kw) Sys. (kw) Sys. (kw) Sys. (kw) Sys. Total Sens kw** Total Sens kw** Total Sens kw** Total Sens kw** Total Sens kw** Total Sens kw** 38CKC036-7A, 9A Outdoor With FB4BSF Multipliers for Determining the Performance With Other s Size Capacity Size Capacity FB4BS(F,B) CKC042-9A Outdoor With FB4BSF Multipliers for Determining the Performance With Other s Size Capacity Size Capacity FB4BS(F,B) CKC048-7A, 9A Outdoor With FB4BSF Multipliers for Determining the Performance With Other s Size Capacity Size Capacity FB4BS(F,B)

11 Detailed cooling capacities* (S.I.) continued L/S EVAP AIR EWB CONDENSER ENTERING AIR TEMPERATURES C (kw) Comp. (kw) Comp. (kw) Comp. (kw) Comp. (kw) Comp. (kw) Comp. Total Sens kw** Total Sens kw** Total Sens kw** Total Sens kw** Total Sens kw** Total Sens kw** 38CKC060-9A Outdoor With FB4BNF Multipliers for Determining the Performance With Other s Size Capacity Size Capacity FB4BSB * Detailed cooling capacities are based on indoor and outdoor unit at the same elevation and connected by 7.62m of tubing. If other than 7.62m of tubing is used and/or indoor unit is located above outdoor unit, a slight variation in capacity may occur. Total and sensible capacities are net capacities. Blower motor heat has been subtracted. Sensible capacities shown are based on 27 C entering air at the indoor coil. For sensible capacities at other than 27 C, deduct 245 kw per 480 L/S of indoor coil air for each degree below 27 C, or add 245 kw per 480 L/S of indoor coil air per degree above 27 C. When the required data falls between the published data, interpolation may be performed. Extrapolation is not an acceptable practice. ** Unit kw is total of indoor and outdoor unit kilowatts. EWB Entering Wet Bulb 11

12 Detailed cooling capacities* (English) INDOOR COIL AIR CFM (F) EWB See notes on pg. 14. OUTDOOR COIL ENTERING AIR TEMPERATURES F (MBtuh) Comp. (MBtuh) Comp. (MBtuh) Comp. (MBtuh) Comp. (MBtuh) Comp. (MBtuh) Comp. Total Sens kw** Total Sens kw** Total Sens kw** Total Sens kw** Total Sens kw** Total Sens kw** 38CKC018-7A Outdoor With FB4BSF Multipliers for Determining the Performance With Other s Size Capacity Size Capacity FB4BSF CKC024-7A Outdoor With FB4BSF Multipliers for Determining the Performance With Other s Size Capacity Size Capacity FB4BSF CKC030-7A Outdoor With FB4BSF Multipliers for Determining the Performance With Other s Size Capacity Size Capacity FB4BSF

13 Detailed cooling capacities* (English) INDOOR COIL AIR CFM (F) EWB See notes on pg. 14. OUTDOOR COIL ENTERING AIR TEMPERATURES F (MBtuh) Comp. (MBtuh) Comp. (MBtuh) Comp. (MBtuh) Comp. (MBtuh) Comp. (MBtuh) Comp. Total Sens kw** Total Sens kw** Total Sens kw** Total Sens kw** Total Sens kw** Total Sens kw** 38CKC036-7A, 9A Outdoor With FB4BSF Multipliers for Determining the Performance With Other s Size Capacity Size Capacity FB4BS(F,B) CKC042-9A Outdoor With FB4BSF Multipliers for Determining the Performance With Other s Size Capacity Size Capacity FB4BS(F,B) CKC048-7A, 9A Outdoor With FB4BSF Multipliers for Determining the Performance With Other s Size Capacity Size Capacity FB4BS(F,B)

14 Detailed cooling capacities* (English) continued INDOOR COIL AIR CFM (F) EWB OUTDOOR COIL ENTERING AIR TEMPERATURES F (MBtuh) Comp. (MBtuh) Comp. (MBtuh) Comp. (MBtuh) Comp. (MBtuh) Comp. (MBtuh) Comp. Total Sens kw** Total Sens kw** Total Sens kw** Total Sens kw** Total Sens kw** Total Sens kw** 38CKC060-9A Outdoor With FB4BNF Multipliers for Determining the Performance With Other s Size Capacity Size Capacity FB4BSB * Detailed cooling capacities are based on indoor and outdoor unit at the same elevation per ARI standard 210/ If additional tubing length and/or indoor unit is located above outdoor unit, a slight variation in capacity may occur. Total and sensible capacities are net capacities. Blower motor heat has been subtracted. Sensible capacities shown are based on 80 F (27 C) entering air at the indoor coil. For sensible capacities at other than 80 F (27 C), deduct 835 Btuh (245 kw) per 1000 CFM (480 L/S) of indoor coil air for each degree below 80 F (27 C), or add 835 Btuh (245 kw) per 1000 CFM (480 L/S) of indoor coil air per degree above 80 F (27 C). When the required data falls between the published data, interpolation may be performed. Extrapolation is not an acceptable practice. ** Unit kw is total of indoor and outdoor unit kilowatts. EWB Entering Wet Bulb 14

15 Condenser only ratings (S.I.) SST C See notes on pg. 17. CONDENSER ENTERING AIR TEMPERATURES C CKC018-7A TCG SDT KW TCG SDT KW TCG SDT KW TCG SDT KW TCG SDT KW TCG SDT KW CKC024-7A TCG SDT KW TCG SDT KW TCG SDT KW TCG SDT KW TCG SDT KW TCG SDT KW CKC030-7A TCG SDT KW TCG SDT KW TCG SDT KW TCG SDT KW TCG SDT KW TCG SDT KW

16 Condenser only ratings (S.I.) SST C See notes on pg. 17. CONDENSER ENTERING AIR TEMPERATURES C CKC036-7A, 9A TCG SDT KW TCG SDT KW TCG SDT KW TCG SDT KW TCG SDT KW TCG SDT KW CKC042-9A TCG SDT KW TCG SDT KW TCG SDT KW TCG SDT KW TCG SDT KW TCG SDT KW CKC048-7A, 9A TCG SDT KW TCG SDT KW TCG SDT KW TCG SDT KW TCG SDT KW TCG SDT KW

17 Condenser only ratings (S.I.) continued SST C SST Saturated Temperature Entering Compressor ( C) TCG Gross Capacity (kw) kw Total (kw) SDT Saturated Temperature Leaving Compressor ( C) CONDENSER ENTERING AIR TEMPERATURES C CKC060-9A TCG SDT KW TCG SDT KW TCG SDT KW TCG SDT KW TCG SDT KW TCG SDT KW

18 Condenser only ratings (English) SST F See notes on pg. 19. CONDENSER ENTERING AIR TEMPERATURES F CKC018-7A TCG SDT KW TCG SDT KW TCG SDT KW TCG SDT KW TCG SDT KW TCG SDT KW CKC024-7A TCG SDT KW TCG SDT KW TCG SDT KW TCG SDT KW TCG SDT KW TCG SDT KW CKC030-7A TCG SDT KW TCG SDT KW TCG SDT KW TCG SDT KW TCG SDT KW TCG SDT KW CKC036-7A, 9A TCG SDT KW TCG SDT KW TCG SDT KW TCG SDT KW TCG SDT KW TCG SDT KW