Copper convection heaters:

Transcription

1 Copper convection heaters: Dual pipeline models Dual pipeline QMG models since 2009: The Run On Sun Australia copper convection heaters are manufactured to our own strict quality specifications. A pure copper water tube is incased inside an aluminium heat exchanger, fixed inside a bone-white powder coated steel case. The water runs through high quality 18-mm diameter copper tube, this keeps the water clean without the use of additives. The convection heat output ranges between 1200 watts for the smallest model, through to 1900 watts for the largest model. This is achieved at a water temperature of 64-DegC. Our dual pipeline models have been working in many homes since Customers say they are pleasantly surprised by the heat output. Four pipeline models Four pipelines, PTD models new for 2014: The new four pipeline models have just arrived, adding double the heat output energy compared to the duel pipeline models. These models have an extra air intake grill on the front towards the bottom of the case, to allow for convection to the upper pipeline heat exchanger. Three models are available with a heat output range between Watts at a water temperature of 64-DegC. Model Size Heat output in Watts Water temp Price L W H 64-DegC QMG600*800*120-mm Dual 800 x 120 x 600mm 1200 $380 QMG600*1000*120-mm Dual 1000 x 120 x 600mm 1500 $465 QMG600*1200*120-mm Dual 1200 x 120 x 600mm 1900 $550 PTD600*420*120-mm Four 420 x 120 x 600mm 900 $295 PTD600*1020*120mm Four 1020 x 120 x 600mm 2400 $560 PTD600*1520*120mm Four 1520 x 120 x 600mm 3500 $650 Polished stainless steel towel heaters: Model-BLH12/360: $310 Height 910-mm. Width 360-mm. Depth 260-mm. Vertical tubes 32-mm diameter, 1.4-mm thick. Horizontal tubes 22-mm diameter, 1.2-mm thick. Model-BXCH-13/500: $330 Height 980-mm. Width 500-mm. Depth 77-mm. Vertical tubes 38-mm diameter, 1.4-mm thick. Horizontal tubes 22-mm diameter, 1.2-mm thick.

2 1 Stainless steel and nickel coated brass manifold kits for floor heating and convection radiators: Stainless steel manifold kit for floor heating or convection radiators: Hot water inlet manifold. Includes 4 flow control valves, air vent, drain port, a 1 ball valve and 4 pipe joiners which can be removed to expose 1/2 threads. Cool water return manifold. Includes 4 manual check valves, air vent, drain port, a 1 ball valve and 4 pipe joiners which can be removed to expose 1/2 threads. Also includes stainless steel manifold joining brackets. Cost for 4-ports $275 Nickel coated brass Manifold kit for floor heating or convection heaters: Hot water inlet manifold. Includes 4 flow control valves, air vent, drain port, 1 ball valve, temperature gauge and 4 to 9 x circuit joiners. Cool water return manifold. Includes 4 manual check valves, air vent, drain port, a 1 ball valve, temperature gauge and 4 to 9 x 1/2 circuit joiners. Also includes stainless steel manifold joining brackets. Cost for 4-ports $285 Cost for 6-ports $358 Cost for 9-ports $465

3 Hydronic heating cylinders 14-mm coils are 30-meters long, 19-mm coils are 45-meters long on all cylinders. Squat white powder coated stainless steel cylinder: From $1650. Add $250 per 14-mm coil. Add $350 per 19-mm coil. 340-litre capacity. Low to high pressure bearing capability mm high x 700-mm wide. 2-mm thick 316 marine grade stainless steel inner. 0.5-mm powder coated steel outer. 60-mm high-density polyurethane insulation. Choice of zero, one or two inner copper coils. Choice of 14-mm or 19-mm diameter copper coils with 1-mm wall thickness. Customised fittings for various heat sources. Tall white powder coated stainless steel cylinders: From $650. Add $250 per 14-mm coil. Add $350 per 19-mm coil. 100 to 500-litre capacity. Low to high pressure bearing capability. 2-mm thick 316 marine grade stainless steel inner. 0.5-mm powder coated steel outer. 60-mm high-density polyurethane insulation. Choice of zero, one or two inner copper coils. Choice of 14-mm or 19-mm diameter copper coils with 1-mm wall thickness. Customised fittings for various heat sources. 100-litres: 470-mm diameter x 1230-mm high. From $ litres: 540-mm diameter x 1530-mm high. From $ litres: 600-mm diameter x 1880-mm high. From $ litres: 700-mm diameter x 1540-mm high. From $ litres: 700-mm diameter x 1880-mm high. From $2050 Highest quality 850-litre capacity all stainless steel: From $2450. Add $250 per 14-mm coil. Add $350 per 19-mm coil. 850-litre capacity. Low to high pressure bearing capability mm high x 850-mm diameter. 2.5-mm thick 316 marine grade stainless steel inner. 0.6-mm stainless steel outer. 60-mm high-density polyurethane insulation. Choice of 14-mm or 19-mm diameter copper coils with 1-mm wall thickness. Customised fittings for various heat sources. Big 1000-litre low-pressure stainless steel cylinder. From $1950. Add $250 per 14-mm coil. Add $350 per 19-mm coil litre capacity. Low-pressure cylinder mm high x 1000-mm diameter. From 0 to 100Kpa pressure bearing cylinder. (100Kpa = 10 meter head) 1.2-mm thick 316 marine grade stainless steel inner. 0.6-mm thick ribbed stainless steel outer. Zero, one or two copper coils available. Choice of 14-mm x 35-meter or 19-mm x 45-meter copper coils with 1-mm wall thickness. Customised fittings for various heat sources.

4 Examples of two 850-litre tank configurations: Tank Specifications: TYPE-A 850-mm diameter x 2000-mm high. Pressure tank inner, made from 2.5-mm thick 316L stainless steel. Outer made from 0.6-mm stainless steel. Top copper coil to be 40-meters long, 3/4. Bottom copper coil to be 30-meters long 3/4. Coil outlet P/T valve Water to the radiators Coil inlet " BSP thread sensor " Sensor Extra large magnesium anode. Extra large magnesium anode T3 Sensor 1/2 T4 Sensor 1/2 Coil outlet Solar return 2000-mm 3/4 P/T Valve. 1 BSP thread. Return water from radiators T2 Sensor 1/2 Coil inlet Cold inlet Solar flow 3/4 BSP thread for copper coil. BSP thread BSP thread 850-mm Tank Specifications: TYPE-B 850-mm diameter x 2000-mm high. Pressure tank inner, made from 2.5-mm thick 316L stainless steel. Outer made from 0.6-mm stainless steel. Top copper coil to be 30-meters long, 14-mm OD and 12-mm ID. Coil outlet P/T valve Water to the radiators " Sensor " BSP thread sensor Coil inlet Extra large magnesium anode T3 Sensor 2000-mm Extra large magnesium anode. BSP thread for P/T Valve. 1 BSP thread for hot water outlets. " BSP thread for copper coil. Solar return Return water from radiators T2 Sensor Drain Cold inlet Solar flow BSP thread. 850-mm

5 Run On Sun heat pipe collectors: Includes a choice of: Flat to roof frame. 15-degree pitched frame. 30-degree pitched frame. Six Run On Sun Australia 30-tube collectors in series, total of 180 tubes. All evacuated tube collectors come with a heavy-duty 2-mm thick stainless steel frame and a stainless steel manifold housing. (No dissimilar metals) 58-mm x 1800-mm Tri-tubes with a 15-degree frames for various roof pitches and latitudes. heavy-duty 2-mm thick glass sidewall. (32-mm hail rating) 12-tube collector $ tube collector $ tube collector $ tube collector $1620 Special prices for 3 or more collectors. 30-degree frames for various roof pitches and latitudes. We stock 12, 18, 24 and 30 tube heat pipe collectors, the 30-tube collectors are the standard for hydronic heating and are normally connected in series. The quantity needed will depend on your application, generally speaking, allow one tube per 10-litres of water storage. More can be used when a summer heat dump application is used such has thermal mass ground storage, this can dissipate and store the extra heat that is generated in summer for later use in winter. Tubes can also be covered with shade cloth during summer to back them off.

6 Run On Sun Australia P/L Heat pipe collectors Quality-Certification So many non-certified low cost Chinese brands are showing up in the Australian market with no certification. The copper content and lead content are unknown, these may cost less, but low purity copper is associated with pin-hole corrosion making them false economy. The Run On Sun heat pipe collectors are high quality and are not limited to the Australian standards. The same collectors are rebadged under different brands that have full European, Canadian, US and UK certification. EN : 2006 European solar keymark, mandatory for all solar collectors sold throughout Europe. Tested by TUV Rhineland and Certified by DIN CERTICO. SRCC performance testing for the United States. Certified by SRCC. AS/NZS Design and construction. Certified by Global Mark. AS/NZS Solar collector performance testing Certified by Global Mark. AS/NZS Energy savings for Victoria prior to April Certified by Sustainability Victoria. AS/NZS Energy savings for Victoria. Mandatory for all solar water heaters and solar collectors sold in Victoria from April Certified by Sustainability Victoria. AS/NZS-4020 Products in contact with potable water. Certified by Global Mark. AS/NZS ID No:

7 Run On Sun Australia Pumps for solar circuits or hydronic heating Grundfos solar-20 low energy hot water circulation pump used for circulating water through a maximum of three 30-tube collectors, or up to 4 convection heaters. Speed 1 = 20 Watts, speed 2 = 25 watts, speed 3 = 30 watts. 2-years warranty $180 2-years warranty $ volt DC hot water pumps for a single heat pipe collector can be used for hydronic heating circuits. TS5 5-watt pump with a 12-month warranty $120. TS5 15-watt pump with a 12-month warranty $140. These pumps can work from a solar panel, regulator and a battery. Pump controllers are available. Large power 3-speed pump. 2 bore with 1.75 unions, used for multiple floor heating circuits. Stainless steel body. Big flow capabilities. Speed-1 = 135 Watts, speed-2 = 190 Watts, speed-3 = 245 Watts. 5-years 5-years warranty warranty $295 $265 Low energy 3-speed hot water circulation pump used to circulate the hot water from the evacuated tube collectors to the cylinder. Can be used on smaller floor heating circuits and convection heater circulation. Tested by Run On Sun to Australian standard AS/NZS4020 Speed-1 = 40 Watts, speed-2 = 60 Watts, Speed-3 = 85 Watts. 5-years warranty. $150 5-years warranty $170 Extra power 3-speed hot water circulation pump used to circulate the hot water through medium sized floor-heating circuits. Tested by Run On Sun to Australian standard AS/NZS4020 Speed-1 = 46 Watts, speed 2 = 80 Watts, speed 3 = 100 Watts. 5-years warranty $165 5-years warranty $180 Pump selection for hydronic heating.

8 Run On Sun Australia Pty Ltd Web: Phone: (02) Pump controllers Premium Aestiva: Pre-wired controller for solar circuit pump. Ready to plug in and work. Designed in Australia. Outdoor waterproof rating. $220 SR208C Controller: Controller for solar circuit pump. Not pre-wired. Comes with all sensors. $150 SR868C Controller: Two part controller for solar circuit pump, with one extra sensor that can turn a second pump on at a preset temperature and off at a preset temperature. Not pre-wired. Comes with all sensors. Plug and cord included. $195 SR988C1 Controller: Multi function controller with many features. Ideal for complex hydronic heating circuits. 2 x Pt1000 sensors. 10 x NTC10K sensors. 9 relays for circulation pumps or 3-way magnetic valves. 1 relay for auxiliary heating. $450 ROSA-100 and ROSA-200 PV pump controllers. ROSA-100 Connects to a solar panel for the power source. ROSA-200 Connects to a solar panel and a battery. This controller incorporates freeze protection for the solar collector outside the hours of operation for a solar panel. ROSA-100: 5-watt pump controller with a 5-Watt solar panel $160 ROSA-100: 15-watt pump controller with a 15-Watt solar panel $175 ROSA-200: 5-watt pump controller, 7Ah battery, 10-Watt solar panel $195 ROSA-200: 15-watt pump controller. 7 Ah battery, 20-Watt solar panel $210

9 Run On Sun Australia supplied the tank, pumps and evacuated tube collectors. A 10-circuit manifold distributor becomes part of the unfinished plant room and connects all of the floor heating circuits for individual control. The pipes leading to the summer heat dump, before the manifold distributors are set up inside the plant room. The fully insulated summer heat dump managed to raise the ground temperature to 70-DegC. The role is reversed in winter, bringing the heat stored in this thermal mass back to the 500-litre cylinder when needed. The plant room showing a Run On Sun 500-litre duel coil tank with pumps, gas booster, house heating circuits and heat dump circuit.

10 Inside the plant room showing the Run On Sun solar collector pump. Cistern to keep the 500-litre cylinder topped up. Run On Sun large bore pump driving the floor circuits. Run On Sun large bore pump driving the ground thermal mass circuits. Run On sun evacuated tube collectors, the main heat source for the whole project. Finished project.