HISD FOOD SERVICES Cafeteria Kitchen Equipment Specifications. May 2010

Size: px
Start display at page:

Download "HISD FOOD SERVICES Cafeteria Kitchen Equipment Specifications. May 2010"

Transcription

1 HISD FOOD SERVICES Cafeteria Kitchen Equipment Specifications May 2010

2 Contents Table of TN Numbers General Conditions Specifications General Requirements Maintenance And Service Qualifications Guarantee Orders / Deliveries / Invoicing vi viii viii viii viii ix ix Equipment Testing And Approval Procedures x Objective x Scope x Procedure x I. Preliminary Review xi II. Requisition xi III. Testing Procedure xi IV. Performance Report xii V. Determination Of Acceptance Or Rejection xii VI. Ongoing Evaluation xii Slicers, Mixers & Cutters 1 6 Wedge Sectionizer, TN Vegetable Press, Manual, Bipod Base TN Vegetable Press, Manual, Wall Mount TN-004A 1 Slicing Machine TN Food Processor TN Blender, w/stainless Container, TN Mixer, 20 Quart TN-010A 2 Mixer, Sixty Quart TN Food Cutter TN Can Opener, Electric TN Can Opener, Manual TN-107A 3 Refrigeration 4 Ice Cream Cabinet, Four Square TN Milk Cooler, Double Drop Front TN-020A 4 Ice Cream Cabinet, Two In Line TN-053A 4 Freezer, Chest, 25 Cu. Ft. TN Freezer, Chest, 20 Cu. Ft. TN Walk-In Cooler/Freezer Specifications TN Walk-In Cooler/Freezer Specifications, Self Contained TN-078SC 8 - i -

3 Milk Cooler, Double Drop Front, Super Bar TN Refrigerator, One Door TN Refrigerator, One Door TN-270A 12 Refrigerator, two Door TN Refrigerator, Two Door TN-280A 13 Refrigerator, Three Door TN Refrigerator, Three Door TN-290A 14 Freezer, One Door TN Freezer, One Door TN-300A 15 Freezer, Two Door TN Freezer, Two Door TN-310A 15 Freezer, Three Door TN Freezer, Three Door TN-320A 16 Ice Machine, 300 lb. Production TN Ice Machine, 500 lb. Production TN Ice Storage Bin TN Tables, Carts & Counters 17 Cart, Dish, Polyethylene TN Cart, Dish, Stainless Steel TN Dolly, Milk Case TN Table, Work (4') TN Table, Cook With Pot Rack And Sink (10') TN Table, Cook (10') TN-022A 19 Table, Work (6') TN-022B 19 Table, Cook (10') With Pot Rack, Less Sink TN-022C 19 Table, Work (6') With Pot Rack TN-022D 20 Table, Work (8') TN-022E 20 Table, Work (8') With Pot Rack TN-022F 20 Table, Cook (8') With Sink TN-022G 20 Table, Baker's With Bins (8') TN Sink, Pot And Pan TN Sink, Vegetable TN Rack, Bun TN Shelving, Solid TN-078A 23 Dunnage Rack TN-078B 24 Shelving, Vented TN-078C 24 Wall Shelves, Stainless Steel TN-078D 24 Cooking Appliances 23 Oven, Gas, Double Convection With Plain Doors TN-041A 24 Oven, Gas, Single Convection With Plain Doors TN-042A 25 Range, Grate Top TN ii -

4 Range, Grate Top With Convection Oven TN Pan, Braising TN Two Compartment Forced Convection Steamer On 24 Inch Cabinet Base TN Steamer, Without Boiler TN-106A 28 Steamer Stand (For TN-106A) TN-106B 28 Oven, Microwave, Commercial TN Oven, Electric, Cooking And Holding TN Cabinet, Proofing TN Laundry, Warewashing & Hot Water 28 Washer, Clothes TN Dryer, Clothes TN-007A 30 Washer/Dryer, Stackable TN-007B 30 Disposer (2 HP) TN Disposer (1 HP) TN-037A 31 Disposer (3 HP) TN-037B 31 Booster Heater, 15 kw TN Booster Heater, 24 kw TN-039A 32 Booster Heater, 30 kw TN-039B 32 Booster Heater, 40 kw TN-039C 32 Booster Heater, 45 kw TN Water Heater, Large TN Water Heater, Large TN-102A 33 Water Boiler, Large with Pump TN Storage Tank, Hot Water TN Holding & Serving 34 Serving Unit, Portable, Self Contained TN Serving Line, Portable, Kiosk TN-068K 35 Serving Unit, Cold, With Double Overshelf TN Serving Unit, Cold, Single Overshelf Without Lights TN-069A 36 Serving Unit, Cold, With Double Tier Display Stand, Stainless Steel Surface TN-069SS 36 Serving Unit, Hot TN Serving Unit, Hot, With Single Tier Serving Shelf, Three Pan Unit, Solid Steel Surface TN-070CSS 36 Serving Unit, Hot, With Single Tier Serving Shelf, Five Pan Unit, Stainless Steel Surface TN-070ESS 37 Serving Unit, Flat Top, Three Pan Size TN-071C 37 Serving Unit, Flat Top, Four Pan Size TN-071D 38 Serving Unit, Flat Top, Five Pan Size TN-071E 38 Serving Unit, Flat Top, Three Pan Size, Stainless Steel Surface TN-071SS 38 Serving Unit, Flat Top, Small TN-071X 38 - iii -

5 Table, Cashier TN Table, Cashier, Stainless Steel Surface TN-072SS 39 Table, Cashier, Large TN Serving Unit, Hot, Super Bar TN Cabinet, Hot Pass Thru, Super Bar TN Cabinet, Hot, Super Bar TN Warmer, Chili, Super Bar TN Buffet Cart, Single Well TN-110A 41 Buffet Cart, Three Well TN-110C 41 Buffet Cart, Four Well TN-110D 41 Buffet Cart, Five Well TN110E 41 Overshelf, Dual Service, Two Pan Unit TN-111B 42 Overshelf, Dual Service, Four Pan Unit TN-111D 42 Overshelf, Dual Service, Five Pan Unit TN-111E 42 Overshelf, Single Service, One Or Two Pan Units TN-113B 43 Overshelf, Single Service, Three Pan Unit TN-113C 43 Overshelf, Single Service, Four Pan Unit TN-113D 43 Overshelf, Single Service, Five Pan Unit TN-113E 43 Hot Pan Drop-In, Single Pan TN-114A 44 Hot Pan Drop-In, Three Pan TN-114C 44 Hot Pan Drop-In, Four Pan TN-114D 45 Hot Pan Drop-In, Five Pan TN-114E 45 Ice Pan Drop-In, Three Pan TN-115C 45 Ice Pan Drop-In, Four Pan TN-115D 45 Ice Pan Drop-In, Five Pan TN-115E 46 Sneeze Guard, Double Deck, Three Pan Unit TN-117C 46 Sneeze Guard, Double Deck, Four Pan Unit TN-117D 46 Sneeze Guard, Double Deck, Five Pan Unit TN-117E 46 End Panel, Laminate Covered TN Adapter Plate, Two Hole 8-1/2" Inserts TN Refrigerated Drop-In, Three Pan TN-120C 47 Refrigerated Drop-In, Four Pan TN-120D 47 Refrigerated Drop-In, Five Pan TN-120E 47 Cabinet, Hot, Food Transport/Service TN Cabinet, Hot, Food Transport/Holding TN Cabinet, Hot, Food Transport TN Protector Case, with Plexiglass Sneeze Guard, Two Pan Unit TN-124B 49 Protector Case, with Plexiglass Sneeze Guard, Three Pan Unit TN-124C 49 Protector Case, with Plexiglass Sneeze Guard, Four Pan Unit TN-124D 49 Protector Case, with Plexiglass Sneeze Guard, Five Pan Unit TN-124E 49 Frostop, Refrigerated Drop-In, Three Pan TN-170C 50 Frostop, Refrigerated Drop-In, Four Pan TN-170D 50 Frostop, Refrigerated Drop-In, Five Pan TN-170E 50 - iv -

6 Tray Rail, Two Well Cart TN-175B 51 Tray Rail, Three Well Cart TN-175C 51 Tray Rail, Four Well Cart TN-175D 51 Tray Rail, Five Well Cart TN-175E 51 Work Shelf, Solid Two Well Cart TN-180B 52 Work Shelf, Solid Three Well Cart TN-180C 52 Work Shelf, Solid Four Well Cart TN-180D 52 Work Shelf, Solid Five Well Cart TN-180E 52 Merchandising 53 Twin Beverage Dispenser, Super Bar TN Sandwich Display TN Warmer, Lighted Display TN Warmer, Pass Thru, Lighted Display TN Popcorn Popper With Holding Unit TN Cabinet, Display and Hold TN Ice Dispenser, 90 lb. TN Ice Dispenser, 150 lb. TN Ice Dispenser, 220 lb. TN v -

7 Table of TN Numbers TN TN-069SS...37 TN TN TN TN-070CSS...37 TN-004A...1 TN-070ESS...37 TN TN-071C...37 TN-007A...30 TN-071D...38 TN-007B...30 TN-071E...38 TN TN-071SS...38 TN TN-071X...38 TN-010A...2 TN TN TN-072SS...39 TN TN TN-020A...4 TN TN TN TN TN TN-022A...19 TN-078SC...8 TN-022B...19 TN-078A...23 TN-022C...19 TN-078B...24 TN-022D...20 TN-078C...24 TN-022E...20 TN-078D...24 TN-022F...20 TN TN-022G...20 TN TN TN TN TN TN-037A...31 TN TN-037B...31 TN TN TN TN-039A...32 TN TN-039B...32 TN TN-039C...32 TN TN TN-102A..33 TN-041A...24 TN-102B...33 TN-042A...25 TN TN TN TN TN TN-053A... TN-106A...28 TN TN-106B...28 TN TN TN-068K...35 TN-107A.3 TN TN-069A vi -

8 TN-110A...41 TN-110C...41 TN-110D...41 TN-110E...41 TN-111B...42 TN-111C...42 TN-111D...42 TN-111E...42 TN-113B...43 TN-113C...43 TN-113D...43 TN-113E...43 TN-114A...44 TN-114C...44 TN-114D...45 TN-114E...45 TN-115C...45 TN-115D...45 TN-115E...46 TN-117C...46 TN-117D...46 TN-117E...46 TN TN TN-120C...47 TN-120D...47 TN-120E...47 TN TN TN TN-124B...49 TN-124C...49 TN-124D...49 TN-124E...49 TN TN TN TN TN TN TN-170C...50 TN-170D...50 TN-170E...50 TN-175B...51 TN-175C...51 TN-175D...51 TN-175E...51 TN-180B...52 TN-180C...52 TN-180D...52 TN-180E...52 TN TN TN-270A 12 TN TN-280A...13 TN TN-290A...14 TN TN-300A...15 TN TN-310A...15 TN TN-320A...16 TN TN TN TN TN TN TN TN TN TN-592a..23 TN vii -

9 General Conditions General Conditions To furnish, deliver, uncrate, and set in place in the Houston Independent School District schools, awarded items of equipment as specified and as required for the period August 1, 2010, through July 31, HISD reserves the option to renew on an annual basis thereafter for two additional oneyear terms with the consent of both parties. Drop shipments direct from factories are not acceptable. Awards will be made on a line item basis, except where noted on shelving and dunnage items TN- 078A, TN-078B, and TN-078C, aluminum cantilever shelving items TN-078E, the basic elements of a cafeteria serving line items TN-069, TN-069A TN-070, TN-071, TN-071X, and TN-072, and the cafeteria serving line with solid surfacing material items TN-069SS, TN-070CSS, TN-070ESS, TN- 071SS, and TN-072SS which will be awarded on the lowest group total. SPECIFICATIONS Please use the enclosed Kitchen Equipment Specifications dated May, 2010, when bidding the items contained in this project. Any item bid as an alternate must include a specification sheet with bid and availability of equipment for review. GENERAL REQUIREMENTS All equipment specified hereinafter shall be fabricated to conform to the requirements and bear the seal for acceptance of the American Gas Association, National Sanitation Foundation, Underwriters Laboratories, the City of Houston, County, and / or State Code as indicated for each piece of equipment. All equipment and materials shall be new, latest design and of first quality. Workmanship shall be of highest grade throughout and in accordance with the Houston Independent School District equipment specifications, revised as attached hereto. All equipment to be replaced (when so stipulated on each purchase order) shall remain on the job site unless noted differently on the purchase order. All items shall be inspected for workmanship and conformity to specifications upon delivery. Items not so conforming or that have been damaged shall not be accepted or installed. The Successful Bidder shall at all times cover and protect his work, materials, fixtures and apparatus to be used therein, from any damage or loss by weather or otherwise, and shall exercise due care to save same from damage. All damage resulting from such neglect shall be made good by him. The Successful Bidder of any item shall provide a black and white photograph or line drawing as appropriate for the specific item to HISD Food Services Purchasing within ten (10) working days from the date of issue of an award letter announcing HISD Board of Education approval. Only genuine photographs or original line drawings will be accepted. Cut sheets, brochures, photocopies, or any printed material will not be considered acceptable. Failure to provide an acceptable photograph or line drawing within ten (10) days will be cause for automatic award to the next lowest bidder. Any awarded item not shipped within the estimated delivery schedule will be cause for automatic cancellation of the order unless otherwise approved by Owner. MAINTENANCE AND SERVICE QUALIFICATIONS No item of equipment will be acceptable unless the following qualifications can be verified to the satisfaction of the Houston Independent School District. Established replacement parts and service shall be available locally. Equipment factory representative must be available for consultation and individual school operating instruction upon installation of any item of equipment. Successful Bidder must provide a local telephone number or a toll free telephone number for technical support and Houston factory representation upon request. Manufacturer must supply ten (10) copies each of Service Repair Manual and Parts Manual for each item awarded. - viii -

10 General Conditions GUARANTEE The Successful Bidder shall give the Owner a written guarantee covering all material and workmanship of the equipment furnished under these specifications, for a period of one (1) year or as specified for the specific piece of equipment, after acceptance by Owner. The Successful Bidder shall replace any defective equipment in whole or in part, as may be necessary, during the guarantee/warranty period. The Successful Bidder shall provide full instructions and demonstrate to the Owner's designated representative proper methods of care, operation and servicing of the equipment. All equipment contained herein is to have one (1) year parts and labor warranty unless otherwise stated. All refrigerator and/or freezer compressors shall be guaranteed for five (5) years. Successful Bidder will be held responsible for compressor replacements, and any freight charges associated with replacements, as needed during the entire five (5) years. ORDERS / DELIVERIES / INVOICING Successful Bidder must provide a local telephone number or a toll free telephone number for both voice and facsimile transmissions. Successful Bidder will confirm receipt of their orders and delivery date therein with Mark Martinez at ; mmarti63@houstonisd.org. Upon receipt of confirming phone call a purchase order number will be issued. Please reference the ship to location and product requested to identify the order when calling. Successful Bidder must make a delivery appointment with the HISD maintenance personnel prior to all deliveries. The individuals designated as Contact Persons are listed below along with their respective phone numbers and pager numbers. Contact Person Office Phone Ramon Crane Jesse Washington Kelvin Bryan All deliveries require the kitchen manager's signature. A signed delivery ticket (or invoice) must be submitted with the original invoice for payment. Mail all invoices to: HISD Food Services Accounting 4400 West 18 St. Houston, Texas Failure to follow the above procedure may result in cancellation of bid award. The vendor is responsible for ensuring that any subcontractor also follows the delivery procedure. - ix -

11 Equipment Testing and Approval Procedures Equipment Testing and Approval Procedures OBJECTIVE To utilize uniform criteria and procedures in evaluating, testing, and specifying Food Services Equipment. SCOPE All kitchen equipment with a value in excess of three hundred dollars ($300.00) is bid annually. Specifications for kitchen equipment are updated annually in the Kitchen Equipment Specifications Manual. Beginning in January, each school year, equipment meetings will be held at all levels to discuss current specifications, test units, and equipment needs for the next bid period. PROCEDURE Procedures for implementation of equipment testing. All Food Services personnel shall utilize the criteria as specified in Sections I through V below, in recommending equipment for testing. I. Preliminary Review. Director of Administrative Services will correlate equipment needs with overall food preparation and service needs. II. Requisition. Director of Administrative Services will prepare a requisition for the equipment. III. Testing Procedure. Maintenance Director and Foreman will complete appropriate report for specific types of equipment tested. IV. Performance Reports. Maintenance Director and Foreman will complete appropriate report for specific types of equipment tested. V. Determination of Acceptance or Rejection. A report of test results will be provided to manufacturers representative. The equipment will be purchased if approved or returned if not approved. VI. Ongoing Evaluation. -

12 I. Preliminary Review Criteria for Preliminary Equipment Review prior to approval for testing all categories of new equipment. A. Manufacturers quality control history. B. Warranty policies. C. Delivery time. D. Dimensions. E. Energy Source. F. Availability of parts and in-service training. G. Test unit availability. H. Compliance with existing specifications. I. Food production application. J. Compliance with all applicable City of Houston codes. K. Verify availability from an approved vendor as indicated by Food Services Purchasing. L. Determine if this is a single source item. M. Identify advantages of the equipment to the District. N. Price/Cost comparison. II. Requisition The Director of Administrative Services will prepare requisition for equipment, clearly marked as a test unit, identifying brand, model, and description. III. Testing Procedure A. Prototype Testing Criteria for testing and development of prototype equipment. 1. Clearly identify product as a prototype. 2. Select a testing site based on District need and equipment function. 3. Utilize current written forms, as applicable, for evaluation. 4. Time line for testing depends on equipment function and need for design modification. B. Six Month Test Criteria utilized for six month in-school testing in Model Schools. - - xi -

13 Equipment Testing and Approval Procedures 1. Exterior and interior design. 2. Durability. 3. Ease of cleaning. 4. Mechanical design and function. 5. Performance appraisal. Does equipment meet manufacturer performance claims. 6. Controls. 7. Response at the school kitchen level. IV. Performance Report Procedures for completing Equipment Performance Report. A. Director of Administrative Services completes the final performance report based on established criteria, written reports, personal observations, and testing of equipment. B. Copies of all reports are filed and results added to the equipment profile data base. C. Director of Administrative Services updates reports as needed and modifies specifications as needed. D. A master specification manual will be maintained with cut sheets for all currently approved equipment. E. A historical file will be maintained with all reports on equipment, filed by TN number, with one folder for non-tn equipment tests. V. Determination of Acceptance or Rejection At the end of the test period, approved products will be purchased and rejected products returned to vendor. A report of test results will be provided to manufacturers representative by Director of Administrative Services. VI. Ongoing Evaluation Criteria for ongoing evaluation of currently approved equipment. Completed work orders shall be used to evaluate currently approved equipment. A. Evaluate frequency and type of maintenance call to identify design or workmanship flaws as indicated by work order tracking. B. Check status of deliveries to determine if there are any problems with availability. C. Correlate equipment function with overall food preparation and service needs. D. Monitor injury reports to evaluate equipment design, placement, and repair needs. -xii- -

14 Slicers, Mixers & Cutters TN-004 VEGETABLE PRESS, MANUAL, BIPOD BASE Vegetable press to be a manual table top style with a bipod base. The vegetable press shall be made of nickel steel with a Teflon plastic pusher and a hardened steel cutter insert. The press shall incorporate an easy change cutter insert and pusher and will accommodate any of the eight (8) cutter accessories. The accessory supplied shall be 3/8 inch cutter. Net weight of the unit shall be 13 pounds with an approximate shipping weight of 16 pounds. French Fry-Vegetable press supplied to this specification shall be Robot Coupe model RP01 or approved equal. TN-004A VEGETABLE PRESS, MANUAL, WALL MOUNT Same as above, without base, wall mountable. Robot Coupe RP04 or approved equal

15 Slicers, Mixers & Cutters TN-009 FOOD PROCESSOR Compact, conveniently designed at 50 angle for operator convenience. Small base occupies minimal counter space. Constructed of anodized aluminum with rubber feet to prevent skidding. Removable top cover is burnished aluminum. Feed chute, pusher and deflector plate of acetal thermoplastic. Electrical: 120 V, 60 C, single phase. Three conductor power cord (18 AWG), eight (8) feet in length. Motor: 7.5 amps. Planetary gear driven operating at 396 to 425 rpm output, 1/2 HP. Interlock switch prevents machine from running when pusher plate swings away or when hopper is opened. Hobart Model FP300 Robot Coupe CL50, or approved equal. Accessories to be included: Plates (1) 1/16" Slicing plate (SLCE-1/16) (1) 5/32" Slicing plate (SLCE-5/32) (1) 7/32" Slicing plate (SLCE-7/32) (1) 3/8" HD slicing plate (SLCE-3/8 HD) (1) 3/16" Shredder plate (SHRED-3/16) (1) 3/8" Dicing plate (DICE-3/8) Racks or holder for plates. TN-010A Mixer 20qt Heavy-duty 1/2 H.P. motor Single point bowl installation Stainless Steel bowl guard Deluxe accessory packages Pg. 2

16 TN-107 CAN OPENER, ELECTRIC Stainless steel; casing with knife assemble, gear and shield removable without tools for easy cleaning and reassembly. NSF certified. Edlund #203 and Edlund #270 or approved equal. TN-200 Wedge Sectionizer Sturdy ABS plastic Sunkist # S-102 or approved equal TN-107A CAN OPENER, MANUAL All stainless steel construction. NSF certified. Edlund S-11 or approved equal. TN-010 Blender 120V NSF. UL, Stainless Container, 32 oz One piece cutting blade Waring # BB150S or approved equal

17 Refrigeration TN-020A MILK COOLER, DOUBLE DROP FRONT 34" W x 30-1/2" D x 39-1/2" H; self contained; mechanically refrigerated; double drop front doors; interior of 18 gauge stainless steel fully welded liner with breaker strip attachment to exterior panels. Exterior and doors of 20 gauge stainless steel with magnetic gasket and stainless steel hinge. Insulation high pressure foamed in place 2" thick polyurethane. R404A refrigerant preferred, hermetically sealed unit with thermostatic adjustment with 1/3 HP motor, 120 V, 3.9 Amps, single plug. Cylinder locks provided on each top door. Rubber corner bumpers provided on each corner, heavy duty 5" stainless steel casters with brakes on two rear wheels. All stainless steel to be type 304 with number 3 finish except door contact cap which will be magnetic type 430 stainless steel, all edges smoothed and rolled, cord and plug installed. Two year warranty parts and labor. To be UL and NSF approved. Mod-userve, or approved equal. Note: Dealer must stock two (2) units at all times for immediate delivery. TN-076 FREEZER, CHEST, 25 CU. FT. 28-3/4" W x 73-7/8" L x 35" H; net storage capacity of approximately 25 cu. ft.; steel cabinet with baked-on enamel finish; adjustable temperature control; hermetically sealed compressor; 115 V, 60 C, single phase; signal light; self leveling; all metal hinge construction, no plastic adjustments; interior light; tumbler lock; self-adjusting seal; defrost drain; three sliding baskets; one vertical divider; three wire cord and plug. General Electric FCM25DS or approved equal. TN-018 FREEZER, CHEST, 5.0 CU. FT. Net storage capacity of approximately 5.0 cu. ft.; manual defrost; adjustable temperature control; side out bulk storage baskets; power "on" light; defrost water drain. General Electric FCM5SUWW-white or approved equal. Pg. 4

18 TN-077 FREEZER, CHEST, 20 CU. FT. 29-1/2" W x 61-1/4" L x 35" H; net storage capacity of approximately 20 cu. ft.; steel cabinet with baked on enamel finish; adjustable temperature control; hermetically sealed compressor; 115 V, 60 C, single phase; signal light; self leveling; all metal hinge construction, no plastic adjustments; interior light; tumbler lock; self-adjusting seal; defrost drain; two sliding baskets; three wire cord and plug. General Electric FCM20DP or approved equal. TN-078 WALK-IN COOLER/FREEZER SPECIFICATIONS 1. PANEL FABRICATION Panels for walls, ceilings and floors shall be nominal 4' in width and shall be interchangeable with like panels. Panels shall consist of foamed-in-place urethane insulation sandwiched between interior and exterior metal "skin" which has been die-formed and gauged for uniformity in size. Edges of panels shall be foamed-in-place tongue and groove with locking facilities and both gaskets foamed-in-place at time of fabrication. Panels shall have a 10 year warranty on all components. A pressure relief port must be provided for all freezers. A weather-proof shield shall be required for all pressure relief ports installed out doors. 2. INSULATION - UNDERWRITERS LABORATORY AND FACTORY MUTUAL LISTED. Each panel shall be completely filled with rigid foamed or poured-in-place urethane. Each panel shall have a thermal conductivity (K factor) of.118 BTU/hr. sq. ft. per degrees Fahrenheit/inch; and an overall coefficient of heat transfer (U factor) of not more than.029 (R factor shall be 34). Insulation shall have a 97% closed cell structure with an average in place density of 2.4 lbs./cu. ft. (if wood is used, only Marine Plywood is permitted). 3. FIRE HAZARD CLASSIFICATION Panels must conform to Fire Hazard Classification, according to ASTME-84 (U.L. 723), shall have a flame spread rating of 25 or less and be toxicity rated. A certifying Underwriters Laboratory label must be on every panel showing. Aluminum Panel Core Material Flame Spread Fuel Contributed 0 0 Smoke Developed Panels must be approved as a Classified Building Unit, be Factory Mutual approved, must have City of Houston and the Architects Building Code approval

19 4. SURFACE FINISHES Panel finishes shall be constructed of.040 stucco embossed aluminum on the exterior and interior. Where applicable, use existing floor or design insulated tile floor for new construction. If the existing floor cannot be used, then interior floors shall be 3/16 diamond treadplate aluminum and withstand uniformly distributed loads of 600 pounds per square foot. Non skid strips shall be installed on all floors. Entrance doors, interior and exterior, shall be at least 22 gauge, type 304, #3 finish stainless steel. 5. ENTRANCE DOOR AND DOOR PANEL Each walk-in will be fitted with one standard 34" W x 78" H 16 gauge stainless steel in & out swing type entrance door. The door must be flush type. Doors must be listed by Underwriters Laboratories. A. 1. Door shall be equipped with magnetic gasket. 2. Posi-Seal door closure and latch to open door by breaking magnetic force of gasket. 3. Hardware with provisions for locking. 4. Safety release which prevents entrapment. B. Door shall be self-closing with strap-type, cam-lift hinges and Posi-Seal door closure. C. Door jamb shall be made of heavy "U" channel type, reinforced steel frame of not less than 14 gauge thickness around entire perimeter with thermal break. D. An isolated, low wattage heater strip covered by magnetically attracting stainless steel shall be fitted onto this jamb. This strip shall provide perfect sealing of magnetic gasket and prevent frost and condensation build up. Heat strip to be in door and frame. E. Each door section shall be provided with an incandescent type vapor proof light, with pilot light switch, wire guard and rigid conduit between switch box and outlet. F. A heavy gauge threshold with non-skid stripping shall be provided with each door section. G. A 2-1/2" diameter chrome plated NSF listed thermometer shall be included with each door section. 6. LIGHTING: Additional protected incandescent lighting to provide 20 ft. candles of light to all areas. 7. NSF RATED Walk-in shall be fabricated to comply with National Sanitation Foundation Standard No. 7 and carry the NSF Label. Pg. 6

20 8. REFRIGERATION SYSTEMS: Refrigerant shall be R-404A when available on all coolers. Temperature on all coolers shall be +35 F. Refrigerant shall be R-404A when available on all freezers. Temperature on freezers shall be -10 F. Coplematic compressors (no substitute). Evaporators to be matched with condensing unit BTU output. Condensing units shall be factory assembled and UL listed. Fan motors, guards, multi-fin and tube type coil shall be housed in heavy gauge aluminum housing. Unit shall have a drain pan with suitable drain pipe connection. Freezer evaporators shall have an automatic electric defrost system including heaters, time clock, fan delay control, heated drain pan and heated drain pipe. Defrost shall be time initiated and terminated with built-in safe control. All evaporators shall be UL listed. Electrical specifications will be provided for each project. 9. ONE OF THE FOLLOWING SYSTEMS SHALL BE SUPPLIED AS THE INDIVIDUAL JOB SPECIFICATION WILL CALL FOR: A. REMOTE SYSTEMS Systems supplied with necessary major parts for field installation by refrigeration, plumbing, and electrical contractors. Remote parts will include condensing unit, evaporator, controls, expansion valve, dryer, sight glass, vibration eliminator, evaporator mounting kit and condenser mounting brackets or rack. B. PREASSEMBLED REMOTE SYSTEMS Same components as outlined in paragraph A., with all parts mounted. This system will be designed to reduce field labor and will require only tubing and electrical hook-up supplied by refrigeration and electrical contractors. C. TOP-MOUNTED OR SIDE-MOUNTED SELF- CONTAINED FACTORY ASSEMBLED SYSTEMS Same components as outlined in paragraph A., requiring only electrical connection and drain lines by contractors. System shall have quick disconnect precharged lines for easy, economical installation. 10. MODERATE LOW AMBIENT KITS WITH PUMP DOWN Outdoor condensing units must include pressure control to govern condenser fan operation, crankcase heater, temperature control, solenoid valve for pump down and rain proof housing. High pressure control

21 11. COMPRESSORS SHALL HAVE A 5 YEAR LIMITED WARRANTY 12. INSTALLING CONTRACTOR A. Shall comply with local codes and take out necessary permits. B. Provides start up. C. One year free labor on complete walk-in and refrigeration system. 13. SUCCESSFUL BIDDER Shall be held responsible for compressor replacements as needed during the entire five years. 14. Bally Engineered Structures, Inc., Kolpak, or Thermo Kool, using Coplematic compressors and low profile evaporators or approved equals. These are specified to establish a quality standard. Any alternates must be prequalified and approved, with engineering data and samples submitted to the Food Services Department ten (10) days prior to bid opening. Any changes in general construction due to an alternate will be at the sole cost of the installing contractor. Note: Refer to TN-78C Shelving (Vented) for the specification of the shelving to be furnished in both walk-in refrigerators and walk-in freezers. TN-078SC WALK-IN COOLER/FREEZER SPECIFICATIONS, SELF CONTAINED 1. GENERAL The walk - in shall be factory prefabricated and of unitized design specifically constructed for outdoor use. The walk - in will allow installation without assembly and relocation without disassembly. The walk - in shall require an on site contractor responsible for the pouring of a concrete pad, connection of electrical power supply to each refrigeration system and for flashing the walk - in to the building wall. The walk - in shall bear the label of the following National Certification Agencies: National Sanitation Foundation (NSF Standard #7) Underwriters Laboratories (Major Refrigeration Components) Underwriters Laboratories (Major Electrical Components) Underwriters Laboratories (Class I Urethane) The walk - in shall comply with the following model building codes: International Conference of Building Officials Southern Building Code Congress International Building Officials Congress Association National Electric Code Pg. 8

22 2. SIZE AND CAPACITY The walk - in shall be built to specified interior and exterior dimensions as shone on the plans or drawings. The walk - in shall have sufficient refrigeration to maintain (+ 35 F, of, -10 F) temperature inside the compartment when the ambient temperature is 100 F, the average number of door openings is four per hour, and there is no heat load from warm products entering unit. The refrigeration system shall be wired to run on VAC 60 Hz / 3 Phase or 1 Phase) power. 3. STRUCTURE The walk - in structure shall be constructed with a fiberglass or embossed aluminum interior and exterior and a 4" urethane core. the interior and exterior fiberglass shell shall be completely seamless and will form a one piece structure to eliminate air and moisture migration. The interior walls shall be finished in white gel coat and the exterior shall be coated with an industrial enamel finish. All doors opening into a controlled temperature room shall be supplied with door frame heaters which shall supply sufficient heat to prevent condensation or frost accumulation. Door jamb flashing shall be stainless steel. Doors shall be provided with a magnetic gasket around the perimeter. Flush bottom doors shall be provided with an adjustable vinyl sweep gasket. When door is closed it shall form a positive airtight seal. Door gaskets shall be installed in retainers for easy replacement. Doors shall incorporate a positive snap action latch with adjustable strike. The latch shall be equipped with a cylinder lock and OSHA approved inside safety release mechanism to prevent entrapment. The hardware shall be chrome finished and mounted with stainless steel tamper proof screws. Doors shall be equipped with heavy duty strap type door hinges. They shall be cam lift type, self closing with nylon bearings and door lift off capability. Hardware shall be chrome finished and mounted with stainless steel tamper proof screws. Doors shall be hinged and sized as shown on plans or drawings. 4. THERMOMETER A 2" flush face dial type thermometer will be mounted adjacent to entry door. Thermometer shall be NSF approved. 5. SELF CONTAINED REFRIGERATION SYSTEM Packaged refrigeration system shall be factory installed by the walk - in manufacturer. Systems shall be complete and ready to operate without field assembly, installation or start up. Refrigerants shall be non-flammable type R - 22, or R404A. Electrical controls including circuit breakers shall be supplied, installed and ready to operate with single point electrical connection by others. Refrigeration system shall be roof mounted

23 Refrigeration systems shall be factory tested for a minimum of 24 hours prior to shipment. Partition walls shall be constructed in the same manner as the exterior walls with a 4" urethane core. 6. FLOOR A 4" insulated (R-32) prefabricated floor shall be supplied and bonded to the walls. The floor shall be reinforced with woven fiberglass or polished aluminum on top of a 1/2" plywood sub floor bonded to the urethane core forming a water tight seal. a skid resistant finish shall be applied to this surface. the floor shall be constructed for permanent elevation 1-1/2" above grade. The elevation provides for air circulation under the floor to eliminate corrosion and the need for an insulated and/or ventilated slab. A welded, heavy duty steel frame shall be encased in fiberglass or aluminum and permanently bonded to the floor to ensure total portability without damage to the walk - in. The floor shall have the capacity to support 400 lbs/sq. ft. of evenly distributed load. 7. INSULATION All insulation shall be a minimum of 4" thick rigid polyurethane foam chemically bonded to the interior and exterior fiberglass walls to form a one piece structure. The thermal conductivity (k) shall not exceed 125 (btu s/in/sq.ft./hr. F) the thermal resistance factor shall not be less than 32. The insulation shall be U.L. Class I rated having a flame spread of not more than 25, fuel contributed of 0 and smoke developed of LIGHTING Walk - in shall be complete with incandescent light fixtures factory installed and tested for proper operation prior to shipment. An incandescent light switch shall be mounted adjacent to entry door and incorporate a visible pilot light to indicate when lights are in the on position. 9. DOORS Doors shall be constructed in the same manner as the walls with no less than 4" urethane insulation. TN-777 Freezer/Cooler Temperature Monitoring System Part 1: XWEB: Monitoring and Control for HACCP and Energy Savings Used for recording all temperature in a minimum of 15 minute intervals, for 1) year; up to 247 addresses of control/monitoring; managed alarms; RS485 two wire/optional 1500 ft. wireless; system access via standard browser: Explorer, Firefox, Safari etc.; built in web pages: Runtime,graphs, alarms, etc.; communicates RJ45 Ethernet, LAN line, or internet using static IP address; Homepage, single view, parameter programming, run time, scheduling, performance meter Part 2: XJP60D Network Module for Monitoring system Six inputs for temperature; serial communication to XWEB; three digital inputs(door alarms); RS485 Connections; temperature range of -58/230 degrees F; 24Vac Class 2cULus; pre-programmed and Pg. 10

24 pre-addressed for NTC temperature recording / every 15 minutes; two level control password protected; hot key flash memory device for internal memory without power. Weiss Instruments or approved equal. TN-095 MILK COOLER, DUAL- ACCESS TWIN TOP Unit include lids, doors, adjustable hinges, door latches and interior made from stainless steel. Floors are heavily reinforced by seam less liner. Heavy duty, epoxy coated steel wire floor racks are provided for added floor protection. Liner bottoms to be made of 300 series stainless. Flexible compression gaskets ensure tight seal. All steel construction with 3-screw hinges. Self latching doors. external thermometer required. Insulation to be 1.5 to 2" thick polyurethane, CFC free. All stainless steel exterior finish and interior finish is required. Refrigerant to be 404a and CFC free, hermetically sealed unit with thermostatic adjustment with 1/3 HP motor, 115 V, 10.1 Amps, single plug, cord and plug installed for ready plug in. Cylinder locks provided on each top door. Rubber corner bumpers provided on each corner, heavy-duty 5" stainless steel casters with brakes on two rear wheels. All stainless steel to be type 300 series or better, all edges smoothed and rolled, cord and plug installed. One year warranty parts and labor. Five year warranty on the compressor. To be UL and NSF approved. Mod-u-serve, or approved equal. Note: Dealer must stock two (2) units at all times for immediate delivery. TN-270 REFRIGERATOR, ONE DOOR Refrigerator, One Door, 22.4 cubic feet capacity; 1/3 HP refrigeration system; 115 volt with cord and plug attached. Full length door, four (4) 6" castors, interior temperature of +38 F when operating in a 100 F ambient environment. Three (3) epoxy coated shelves mounted on fully locking shelf supports adjustable on 1" increments. Interior floor to be stainless steel. Stainless interior and exterior, full door perimeter non-conducting thermal breaker strips with operator controlled perimeter heaters. Doors are fully insulated and to be field reversible with fully recessed handles. Door hinges are self-lubricating cam lift hinges with chrome plating. Exterior front including doors, front frame, door header, door sill, and front enclosure panels to be stainless steel. Refrigeration system is to be top mounted, with a thermostatic expansion valve. System is to be fully sealed and using 134A

25 refrigerant, plasticized evaporator coil, and service valves located behind front panel. Entire assembly is to be UL approved and listed under NSF Standard #7 for operation and sanitation. Unit will carry a two (2) year warranty covering parts and labor, with a five (5) year parts warranty on the compressor and evaporator coil. McCall model , or approved equal. TN-270A REFRIGERATOR, ONE DOOR Refrigerator, One Door, 30 wide x 34-1/2 deep x 84 high, 24cu.ft. capacity. 1/4hp compressor; 115 volt with cord and plug attached. Stainless steel front, sides and interior. Door shall be self-closing, with adjustable edge mounted hinges. Light switch shall be concealed in hinge. Unit shall be equipped with easy replaceable condensate heaters around all door openings. Breaker strips shall be impact resistant PVC and be of two piece design. Refrigeration valve shall be expansion valve type. Condensing unit shall be equipped with integral receiver, high and low side service valves and access ports, and shall be top mounted. Condenser fan shall have a guard which completely covers fan blade. Unit shall have removable filter drier and sight glass. Compressor shall have a low pressure cut out. Unit shall be equipped with master power switch. Condensation shall be dissipated using hot gas. Liner corners shall be welded and polished. Insulation shall be high density foamed in place, minimum thickness 2-1/2 inches Shelves shall be chrome plated and supported on adjustable stainless steel shelf standard system. Legs or casters shall be attached to unit using concealed heavy gauge leg channels with threaded stem. 1 year parts and labor warranty and 5 years on compressor. Utility model R-30-SS-1S-D or approved equal. Pg. 12

26 TN-280 REFRIGERATOR, TWO DOOR Refrigerator, Two Door, 49 cubic feet capacity; 1/3 HP refrigeration system; 115 volt with cord and plug attached. Full length doors, four (4) 6" castors, interior temperature of +38 F when operating in a 100 F ambient environment. Three (3) epoxy coated shelves mounted on fully locking shelf supports adjustable on 1" increments. Interior floor to be stainless steel, interior and exterior to be stainless steel, full door perimeter non-conducting thermal breaker strips with operator controlled perimeter heaters. Doors are fully insulated and to be field reversible with fully recessed handles. Door hinges are self-lubricating cam lift hinges with chrome plating. Refrigeration system is to be top mounted with a thermostatic expansion valve. System is to be fully sealed and using 134A refrigerant, plasticized evaporator coil, and service valves located behind front panel. Entire assembly is to be UL approved and listed under NSF Standard #7 for operation and sanitation. Unit will carry a two (2) year warranty covering parts and labor, with a five (5) year parts warranty on the compressor and evaporator coil. McCall model , or approved equal. TN-280A REFRIGERATOR, TWO DOOR Refrigerator, Two Door, 60 wide x 34-1/2 deep x 84 high, 53.4cu.ft. capacity. 1/2hp compressor; 115 volt with cord and plug attached. Stainless steel front, sides and interior. Door shall be self-closing, with adjustable edge mounted hinges. Light switch shall be concealed in hinge. Unit shall be equipped with easy replaceable condensate heaters around all door openings. Breaker strips shall be impact resistant PVC and be of two piece design. Refrigeration valve shall be expansion valve type. Condensing unit shall be equipped with integral receiver, high and low side service valves and access ports, and shall be top mounted. Condenser fan shall have a guard which completely covers fan blade. Unit shall have removable filter drier and sight glass. Compressor shall have a low pressure cut out. Unit shall be equipped with master power switch. Condensation shall be dissipated using hot gas. Liner corners shall be welded and polished. Insulation shall be high density foamed in place, minimum thickness 2-1/2 inches Shelves shall be chrome plated and supported on adjustable stainless steel shelf standard system. Legs or casters shall be attached to unit using concealed heavy gauge leg channels with threaded stem. 1 year parts and labor warranty and 5 years on compressor. Utility model R-60-SS- 2S-D. TN-290 REFRIGERATOR, THREE DOOR Refrigerator, Three Door, 72 cubic feet capacity; 1/2 HP refrigeration system; 115 volt with cord and plug attached. Full length door, four (4) 6" castors, interior temperature of +38 F when operating in a 100 F ambient environment. Nine (9) epoxy coated shelves mounted on fully locking shelf supports adjustable on 1" increments. Interior floor to be stainless steel. Stainless steel interior and exterior. Full door perimeter nonconducting thermal breaker strips with operator controlled perimeter heaters. Doors are fully insulated and to be field reversible with fully recessed handles. Door hinges are self-lubricating cam lift hinges with chrome plating. Refrigeration system is to be top mounted, with a thermostatic expansion valve. System is to be fully sealed and using 134A refrigerant, plasticized evaporator coil, and service valves located behind front panel. Entire assembly is to be UL approved and listed under

27 NSF Standard #7 for operation and sanitation. Unit will carry a two (2) year warranty covering parts and labor, with a five (5) year parts warranty on the compressor and evaporator coil. McCall model , or approved equal. TN-290A REFRIGERATOR, THREE DOOR Refrigerator, Three Door, 90 wide x 34-1/2 deep x 84 high, 84cu.ft. capacity. 1/2hp compressor; 115 volt with cord and plug attached. Stainless steel front, sides and interior. Door shall be self-closing, with adjustable edge mounted hinges. Light switch shall be concealed in hinge. Unit shall be equipped with easy replaceable condensate heaters around all door openings. Breaker strips shall be impact resistant PVC and be of two piece design. Refrigeration valve shall be expansion valve type. Condensing unit shall be equipped with integral receiver, high and low side service valves and access ports, and shall be top mounted. Condenser fan shall have a guard which completely covers fan blade. Unit shall have removable filter drier and sight glass. Compressor shall have a low pressure cut out. Unit shall be equipped with master power switch. Condensation shall be dissipated using hot gas. Liner corners shall be welded and polished. Insulation shall be high density foamed in place, minimum thickness 2-1/2 inches Shelves shall be chrome plated and supported on adjustable stainless steel shelf standard system. Legs or casters shall be attached to unit using concealed heavy gauge leg channels with threaded stem. 1 year parts and labor warranty and 5 years on compressor. Utility model R-90-SS-3S-D. TN-300 FREEZER, ONE DOOR Freezer, One Door, 22.4 cubic feet capacity; 1/2 HP refrigeration system; 115 volt with cord and plug attached. Full length door, four (4) each 6" castors, interior temperature of 0 F when operating in a 100 F ambient environment. Three (3) epoxy coated shelves mounted on fully locking shelf supports adjustable on 1" increments. Interior and exterior to be stainless steel, full door perimeter non-conducting thermal breaker strips with operator controlled perimeter heaters. Doors are fully insulated and to be field reversible with fully recessed handles. Door hinges are self-lubricating cam lift hinges with chrome plating. Refrigeration system is to be top mounted with thermostatic expansion valve. System is to be fully sealed and using R404A refrigerant, plasticized evaporator coil, and service valves located behind front panel. Entire assembly is to be UL approved and listed under NSF Standard #7 for operation and sanitation. Unit will carry a two (2) year warranty covering parts and labor, with a five (5) year parts warranty on the compressor and evaporator coil. McCall model F, or approved equal. Pg. 14

28 TN-300A FREEZER, ONE DOOR Freezer, One Door, 30 wide x 34-1/2 deep x 84 high, 24cu.ft. capacity. 1/2hp compressor; 115 volt with cord and plug attached. Stainless steel front, sides and interior. Door shall be self-closing, with adjustable edge mounted hinges. Light switch shall be concealed in hinge. Unit shall be equipped with easy replaceable condensate heaters around all door openings. Breaker strips shall be impact resistant PVC and be of two piece design. Refrigeration valve shall be expansion valve type. Condensing unit shall be equipped with integral receiver, high and low side service valves and access ports, and shall be top mounted. Condenser fan shall have a guard which completely covers fan blade. Unit shall have removable filter drier and sight glass. Compressor shall have a low pressure cut out. Unit shall be equipped with master power switch. Condensation shall be dissipated using hot gas. Liner corners shall be welded and polished. Insulation shall be high density foamed in place, minimum thickness 2-1/2 inches Shelves shall be chrome plated and supported on adjustable stainless steel shelf standard system. Legs or casters shall be attached to unit using concealed heavy gauge leg channels with threaded stem. Defrost shall be automatic, time initiated, and temperature terminated. Defrost system shall be equipped with distinct termination and safety switches. 1 year parts and labor warranty and 5 years on compressor. Utility model F-30-SS-1S-D or approved equal TN-310 FREEZER, TWO DOOR Freezer, Two Door, 49 cubic feet capacity; 3/4 HP refrigeration system; 115 volt with cord and plug attached. Full length door, four (4) each 6" castors, interior temperature of 0 F when operating in a 100 F ambient environment. Six (6) epoxy coated shelves mounted on fully locking shelf supports adjustable on 1" increments. Interior and exterior to be stainless steel, full door perimeter nonconducting thermal breaker strips with operator controlled perimeter heaters. Doors are fully insulated and to be field reversible with fully recessed handles. Door hinges are self-lubricating cam lift hinges with chrome plating. Refrigeration system is to be top mounted with a thermostatic expansion valve. System is to be fully sealed and using R404A refrigerant, plasticized evaporator coil, and service valves located behind front panel. Entire assembly is to be UL approved and listed under NSF Standard #7 for operation and sanitation. Unit will carry a two (2) year warranty covering parts and labor, with a five (5) year parts warranty on the compressor and evaporator coil. McCall model F, or approved equal. TN-310A FREEZER, TWO DOOR Freezer, Two Door, 60 wide x 34-1/2 deep x 86 high, 54cu.ft. capacity. 3/4hp compressor; 115 volt with cord and plug attached. Stainless steel front, sides and interior. Door shall be self-closing, with adjustable edge mounted hinges. Light switch shall be concealed in hinge. Unit shall be equipped with easy replaceable condensate heaters around all door openings. Breaker strips shall be impact resistant PVC and be of two piece design. Refrigeration valve shall be expansion valve type. Condensing unit

29 shall be equipped with integral receiver, high and low side service valves and access ports, and shall be top mounted. Condenser fan shall have a guard which completely covers fan blade. Unit shall have removable filter drier and sight glass. Compressor shall have a low pressure cut out. Unit shall be equipped with master power switch. Condensation shall be dissipated using hot gas. Liner corners shall be welded and polished. Insulation shall be high density foamed in place, minimum thickness 2-1/2 inches Shelves shall be chrome plated and supported on adjustable stainless steel shelf standard system. Legs or casters shall be attached to unit using concealed heavy gauge leg channels with threaded stem. Defrost shall be automatic, time initiated, and temperature terminated. Defrost system shall be equipped with distinct termination and safety switches. 1 year parts and labor warranty and 5 years on compressor. Utility model F-60-SS-1S-D or approved equal. TN-320 FREEZER, THREE DOOR Freezer, Three Door, 72 cubic feet capacity; 1 HP refrigeration system; 115/208/230 volt. Full length door, four (6) 6" castors, interior temperature of 0 F when operating in a 100 F ambient environment. Nine (9) epoxy coated shelves mounted on fully locking shelf supports adjustable on 1" increments. Interior and exterior to be stainless steel. Full door perimeter non-conducting thermal breaker strips with operator controlled perimeter heaters. Doors are fully insulated and to be field reversible with fully recessed handles. Door hinges are self-lubricating cam lift hinges with chrome plating. Refrigeration system is to be top mounted with a thermostatic expansion valve. System is to be fully sealed and using R404A refrigerant, plasticized evaporator coil, and service valves located behind front panel. Entire assembly is to be UL approved and listed under NSF Standard #7 for operation and sanitation. Unit will carry a two (2) year warranty covering parts and labor, with a five (5) year parts warranty on the compressor and evaporator coil. McCall model F, or approved equal. TN-320A FREEZER, THREE DOOR Freezer, Three Door, 90 wide x 34-1/2 deep x 86 high, 84cu.ft. capacity. 1hp compressor; 115/208/230 volt with no cord and plug attached. Stainless steel front, sides and interior. Door shall be selfclosing, with adjustable edge mounted hinges. Light switch shall be concealed in hinge. Unit shall be equipped with easy replaceable condensate heaters around all door openings. Breaker strips shall be impact resistant PVC and be of two piece design. Refrigeration valve shall be expansion valve type. Condensing unit shall be equipped with integral receiver, high and low side service valves and access ports, and shall be top mounted. Condenser fan shall have a guard which completely covers fan blade. Unit shall have removable filter drier and sight glass. Compressor shall have a low pressure cut out. Unit shall be equipped with master power switch. Condensation shall be dissipated using hot gas. Liner corners shall be welded and polished. Insulation shall be high density foamed in place, minimum thickness 2-1/2 inches Shelves shall be chrome plated and supported on adjustable stainless steel shelf standard system. Legs or casters shall be attached to unit using concealed heavy gauge leg channels with threaded stem. Defrost shall be automatic, time initiated, and temperature terminated. Defrost system shall be equipped with distinct termination and safety switches. 1 year parts and labor warranty and 5 years on compressor. Utility model F-90-SS-1S-D or approved equal.

30 TN-550 ICE MACHINE, 300 LB. PRODUCTION Pg. 16 Ice Machine, having ARI-certified ice production capacity of 300 lbs. per 24 hours at 90ºF air temperature, with half dice cube size: 3/8" x 1-1/8" x 7/8," ice thickness control that assures uniform cube size without using pressure controls or thermostats, type R-404A refrigerant, exterior to be of type 304 stainless steel, 115 volt, 60 cycle, 1 phase, automatic built in self cleaning system with choice of cycle from two, four, or twelve week duration, self contained operation, three years parts and labor warranty, five years parts and labor on evaporator, and 5 year parts and 3 years labor on compressor. Manitowoc model SY0304A or approved equal. Note: Bin and Machine must come from the same vendor. TN-555 ICE MACHINE, 500 LB. PRODUCTION Ice Machine, having ARI-certified ice production capacity of 500 lbs. per 24 hours at 90ºF air temperature, with half dice cube size: 3/8" x 1-1/8" x 7/8," ice thickness control that assures uniform cube size without using pressure controls or thermostats, type R-404A refrigerant, exterior to be of type 304 stainless steel, 115 volt, 60 cycle, 1 phase, automatic built in self cleaning system with choice of cycle from two, four, or twelve week duration, choice of either self contained or remote condenser at time of order, three years parts and labor warranty, five years parts and labor on evaporator, and 5 year parts and 3 years labor on compressor. Manitowoc model SY0504A or approved equal. TN-589 ICE STORAGE BIN Ice Storage Bin, foamed in place urethane insulation, lined with either stainless steel or one piece polyethylene, exterior top, front, sides, and doors shall be polished stainless steel, mounted on 6 inch adjustable legs. Specify ARI rated capacity of 100% fill of 200, 300, 400, 600, 800, 1,000, 1,300, 1,600, 2,000, or 2,600 pounds at time of order. Follett, Manitowoc or approved equal Note: Bin and Machine must come from the same vendor

31 Tables, Carts & Counters Tables, Carts & Counters TN-002 CART, DISH, POLYETHYLENE 21-1/2 " W x 37-1/4" L x 34-5/8" H; three molded polyethylene shelves, 31-1/2 " x 30-5/8" with clearance of 11-3/8" between shelves; two (2) five inch swivel castors; two (2) five inch fixed castors with one brake; 800 pound carrying capacity. Specify color at time of order. Cambro BC 235 or approved equal. TN-003 CART, DISH, STAINLESS STEEL Approximate dimensions 22-3/8" W x 39" L x 37" H, three 18 gauge stainless steel shelves about 21" x 33" with clearance of about 11-3/8" between shelves. All shelf edges will be constructed with ¾" break up, 1" break out, ¾" break down and ¼" break in, welded and polished to each frame leg: 1" stainless steel round tube legs and frame: two (2) 4" swivel castors: two (2) 4" locking swivel castors; all castors made of stainless steel; 650 pound carrying capacity. Must comply with all applicable NSF standards. TN-019 DOLLY, MILK CASE 27" L x 13-3/4" W, with 3" heavy duty castors; one piece angle frame construction; to accommodate two (2) 13" x 13" milk crates. Cambro model CD-1327 or approved equal. TN-021 TABLE, WORK (4') 48" L x 30" W x 34" H; 14 gauge stainless steel top and undershelf; legs, drawer, and adjustable bullet feet of stainless steel. Undershelf must have 12-gauge stainless steel channel support underneath and to be welded and polished to each leg at 8" from floor. Must comply with all applicable NSF standards. Pg. 18

32 TN-022 TABLE, COOK WITH POT RACK AND SINK (10') Rack height 7' 2"; stainless steel adjustable bullet feet; table 30" W x 120" L x 34" H; top of 14 gauge polished stainless steel, 1-1/2" rolled down edges, reinforced with 12 gauge steel channels; full length double bar pot rack over table, supported by capped 1-5/8" O.D. 16 gauge stainless steel pipe standards extending through stainless steel conical gussets, continuously welded, ground and polished to table top and back between table legs; bars of 1/4" x 2" flat bar stainless steel with semi circular ends and 36 fitted removable double prong pot hooks;14 gauge stainless steel undershelf with easily removable sections; two (2) 15" x 20" x 5" drawers; swing spout, faucet and basket strainer for a 15" x 20" x 8" stainless steel sink on right end. NSF certified seal required. Klein 440 pot hooks, Klein conical gusset, Klein adjustable bullet feet, or Tabco SS3010, ST-120 Pot Rack, TA-11A Sink and two (2) SS-1520 drawers. TN-022A TABLE, COOK (10') 30" W x 120" L x 34" H; top and undershelf of 14 gauge polished stainless steel reinforced with 12 gauge stainless steel channels; undershelf to be welded and polished to each leg at 8" from floor; two (2) 15" x 20" x 5" stainless steel drawers. Must comply with all applicable NSF standards. TN-022B TABLE, WORK (6') 72" L x 30" W x 34" H; top and undershelf of 14 gauge polished stainless steel with 12 gauge stainless steel channel support; legs, adjustable bullet feet, and drawer of stainless steel; undershelf to be to be welded and polished to each leg at 8" from floor. Must comply with all applicable NSF standards. TN-022C TABLE, COOK (10') WITH POT RACK, LESS SINK Rack height 7' 2"; stainless steel adjustable bullet feet; table 30" W x 120" L x 34" H; top and undershelf of 14 gauge polished stainless steel reinforced with 12 gauge stainless steel channel; undershelf to be welded and polished to each leg at 8 from floor; full length double bar pot rack over table, supported by capped 1-5/8" O. D. stainless steel pipe standards extending through stainless steel conical gussets, continuously welded, ground and polished to table top and back between table legs; bars of 1/4" x 2" flat bar stainless steel with semi circular ends and 36 fitted, removable double prong pot hooks; 16 gauge stainless steel undershelf with easily removable sections; two (2) 15" x 20" x 5" stainless steel drawers. Must comply with all applicable NSF standards

33 Tables, Carts & Counters TN-022D TABLE, WORK (6') WITH POT RACK Same as TN-22B, but with pot rack. Must comply with all applicable NSF standards. TN-022E TABLE, WORK (8') Same as TN-022b, But with two (2) drawers and 96' L X 30" W X 34" H. Must comply with all applicable NSF standards.. TN-022F TABLE, WORK (8') WITH POT RACK Same as TN-22E, but with pot rack. Must comply with all applicable NSF Standards. TN-022G TABLE, COOK (8') WITH SINK Table 30" W x 96" L x 34" H; top of 14 gauge polished stainless steel, 1-1/2" rolled down edges, reinforced with 12 gauge steel channels; 1-5/8" O.D. 16 gauge stainless steel legs, gussets and 1" adjustable bullet feet; continuously welded, ground and polished to table top and back between table legs; 14 gauge stainless steel undershelf with easily removable sections; one (1) 15" x 20" x 5" drawer; swing spout, faucet and basket strainer for a 15" x 20" x 8" stainless steel sink on right end. Shop fabricated. NSF certified seal required. Klein adjustable bullet feet, or Tabco SS308, TA-11A Sink and one (1) SS-1520 drawer or approved equal. Pg. 20

34 TN-023 TABLE, BAKER'S WITH BINS (8') 96 L X 30 W X 34 H; 14 GAUGE STAINLESS STEEL TOP WITH 6 H INTEGRAL STAINLESS STEEL RISER AT BACK TABLE EDGES AND ENDS; FRONT AND BACK TABLE EDGES AND ENDS TURNED DOWN 1 5/8 ; ALL VERTICAL AND HORIZONTAL CORNERS COVED ON AT LEAST ¼ RADIUS; FULL LENGTH 8 W STAINLESS STEEL CONDIMENT SHELF MOUNTED 18 ABOVE WORK SURFACE; SUPPORTED AT ENDS AND CENTER BY A ¾ 18 GAUGE STAINLESS STEEL TUBING BRACES FORMED TO FIT THE RISER, WELDED TO RISER GROUND, AND POLISHED; 2 TURN UP ON SHELF AT BACK AND ENDS; STAINLESS STEEL GUSSETS FOR LEG MOUNTING; HORIZONTAL CORNERS OF ¼ RADIUS; THREE (3) APPROXIMATELY 20 X 20 X 5 DRAWERS UNDER TABLE WITHIN AN 18 GAUGE STAINLESS STEEL ENCLOSURE ON 6 LEGS WITH ROUNDED VERTICAL CORNERS ENCLOSED ON ALL SIDES SO AS TO BE VERMIN PROOF; ENCLOSURE LOCATED AT RIGHT END NEXT TO THREE (3) APPROXIMATELY 17 ½ X 22 ¼ X 27 ¼ STAINLESS STEEL PORTABLE BINS WITH DEPTH OF 14 MOUNTED OMN FOUR (4) 4 DIAMETER, HEAVY DUTY BALL BEARING, RUBBER TIRED, SWIVEL CASTORS. MUST COMPLY WITH ALL APPLICABLE NSF STANDARDS. TN-047 SINK, POT AND PAN 1. GENERAL Sinks must comply with N.S.F. Standard No. 2 food service equipment and all applicable City of Houston Building and Health Codes. N.S.F. approved sinks will measure no more than 30" front to back by 111" left to right; with compartments measuring no less than 26.5" front to back by 24" left to right (i.d.) by no less than 14" deep (measured from base of well to highest fill level in each compartment, unless otherwise specified). Each compartment will be separated from the next compartment by a 2" wall separation. Drain board may be no smaller than the smallest horizontal dimension of the sink compartments and is to be mounted on the left or right side as indicated for each specific job. 2. MATERIALS Sink compartments, drain boards and back splash will be constructed of 14 gauge number 304 (18-9) stainless steel; stainless steel welded, ground and polished to a number 4 type finish. Legs, braces and cross rails will be on stainless steel tubing at least 1.5" in diameter. Gussets and adjustable bullet feet will be of stainless steel. Removable undershelving will be of 16 gauge No. 302 stainless steel finished to a number 4 finish. Each will be provided with a finger tip release crumb cup strainer assembly with no less than a 1.5" drain. Faucets will be excluded from bid. Drain mechanisms to be twist type

35 Tables, Carts & Counters CONSTRUCTION Minimum fabrication standards will equal or exceed N.S.F. Standard No. 2 Section 4.48 sinks. Construction will be of welded stainless steel. Rims will be 180 degrees 1.5" diameter rolled and extended over both ends and full length of unit. All corners and angles of 110 degrees or less made by two or more planes coming together will be rounded and fully coved in a continuous and smooth radius of no less than 8" above sink wells with no less than a 2" 45 degree return to the wall. Back splash to be pierced with 1-1/4" diameter holes on 8" centers to accommodate 2 faucet units. Faucets to be centered over sink compartments partitions. Bottom of each sink compartment to be pitched or stamped toward drain assembly. Drain assembly to be installed, sealed, tested and provided with a 4" nipple. Drain boards will be pitched toward sink and flat over their front to back dimensions. Pitch will be a minimum of 1/8" per 12 inches of drain board length (l to r). Drain board will be turned up a minimum of 2" and coved on not less than 3/8" radius to match sink front. Support for drain boards will be of same fabrication as sink units. Attachments of drain boards may not subtract from sink compartments minimum depth. Sink assembly and drain boards will be adequately supported by all stainless steel seamless supports. All gussets will be fully attached by welding, ground smooth, sealed from pest habitation and made easily cleanable. Legs are to be of no less than 1-1/2" stainless steel tubing with cross rails welded 10" above floor; with no rail at back of sink well section. Drain boards to have matching legs and be fitted with removable under shelf. Sink and drain board assemblies to adequately support sink under full water loads. Front of sink compartments to be skirted completely across covering the partions and ending at the end sinks with no less than 16 gauge No. 302 stainless steel finished to a No. 4 finish. Note: Installation plumbing to be completed by others. TN-048 SINK, VEGETABLE 60" L, including partition, x 30" W x 46" H, including splashback; 36" high to crown; overall length of sink unit 11 feet; two 16-1/2" D compartments; 14 gauge stainless steel sink, 1-1/2" semi roll rim along front, back turned up 10" high above crown; back to wall on 45 slope; horizontal and vertical corners coved on 3/4" radius, electrically welded, ground smooth and polished; splashback pierced for faucet with non-splash aerator furnished by Food Service Equipment Contractor; back, bottom and front of one piece metal with welded ends and partitions; bottom sloped toward finger tip release drain with connected overflow and removable stainless steel strainer; four 1-1/2" stainless steel tubing legs and crossrails, welded, 10" above floor; no rail at back behind sink; legs fitted with stainless steel gussets welded to sink bottom; stainless steel adjustable bullet feet; two 14 gauge stainless steel drainboards, full sink width x 3' L, on each end of sink, making overall length of sink unit eleven feet; drain boards sloped 3/4" toward sink; 3" H rolled rim at sink and 2-1/4" H at end opposite sink; drain board and splashback to match sink; drain boards mounted on stainless steel legs and crossrails, same as sink; under each drain board furnish 14 gauge stainless steel removable undershelf. NSF certified seal required. Chicago No. 540 LDL8CP faucet; No. B-199 nonsplash Pg. 22

36 aerator; Kenco No. DA-51 finger tip release drain with connected overflow; Klein No gussets; Klein No bullet feet or approved equal. TN-065 RACK, BUN APPROXIMATELY 27 L X 19 W X 68 ½ H; STAINLESS STEEL UPRIGHTS AND LEDGES; WELDED AND POLISHED; FRONT AND BACK TIE BARS; TOP AND BOTTOM CORNER GUSSETS; 4 HEAVY DUTY SWIVEL CASTORS WITH TWO (2) THAT LOCK; TOP AND BOTTOM WILL HAVE WELDED STAINLESS STEEL COVER; FRAME TO BE CONSTRUCTED OF 1 1/8 STAINLESS STEEL SQUARE TUBING; MUST COMPLY WITH ALL APPLICABLE NSF STANDARDS. TN-078A SHELVING, SOLID Posts and longitudinal beams to be constructed of a pultrusion of continuous glass fibers and thermoset resin composite, exterior surfaces are high impact thermoplastic resin; shelves to be constructed of high impact polymer, removable, commercial dishwasher safe. Load capacity of 800 pounds up to 54". Sizes Note: Shelving, Solid and Post should have the same vendor. TN -592 Shelving Starter units (Solid and Vented) Sizes: 12" x 24", 12" x 36", 12" x 42", 12" x 48", 12" x 54",18" x 24", 18" x 36", 18" x 42", 18" x 48", 18" x 54", 24" x 24", 24" x 36", 24" x 42", and 24" x 48", 24" x 54". Made of smooth polypropylene. Rust proof. Wipe clean; Traverses and posts are weight bearing with solid, steel cores; Antimicrobial. Cambro or approved equal. TN-592a Shelving Add-on Kits (Solid and Vented) Sizes 12" x 24", 12" x 36", 12" x 42", 12" x 48", 12" x 54",18" x 24", 18" x 36", 18" x 42", 18" x 48", 18" x 54", 24" x 24", 24" x 36", 24" x 42", and 24" x 48", 24" x 54". Made of smooth polypropylene. Rust proof. Wipe clean; Traverses and posts are weight bearing with solid, steel cores; Antimicrobial. Cambro or approved equal

37 Cooking Appliances TN-078B DUNNAGE RACK Same specification as TN-78A, but with vented shelf and 8" posts. Sizes 18" x 36", 18" x 48", and 24" x 48". Metromax or approved equal. TN-078C SHELVING, VENTED Same specification as TN-78A except individual shelves are vented. Note: Shelving, Vented and Post should have the same vendor. TN-078D WALL SHELVES, STAINLESS STEEL 48" L x 12" W, 14 gauge stainless steel, back and two sides turned up square 1". Front edge to have a sanitary roll. Provided with wall brackets of same material as shelf. Brackets are stud welded to shelf and are removable. NSF certified seal required. Tabco, Aero, or approved equal. Cooking Appliances TN-041A OVEN, GAS, DOUBLE CONVECTION WITH PLAIN DOORS Stainless steel exterior, including stainless steel louvered back panel. Baking compartment, including baffle, to be porcelain enameled steel. Top, back, and sides to be insulated with 1" high temperature mineral fiber sheet. Solid stainless steel doors to have a single handle mounted on left hand door to operate both doors simultaneously to sides, to a total opening of 140 on a horizontal plane. Rack supports shall be chrome plated steel, capable of holding a total of eleven (11) oven racks with a minimum spacing of 1-5/8" O.C. To be furnished with five (5) standard racks (each section). Oven to be heated both directly and indirectly, due to the recirculation of the heated gases. The thermostat shall be electric, direct acting, with a temperature range of 200 F. (93 C.) to 500 F. (260 C.). Thermostat shall control the gas by means of a solenoid valve. Ovens to be equipped with an infinite setting solid state thermostat consisting of a solid state control board with a thermistor sensor probe. Oven constructed with entire control panel to slide out from front, to provide easy access to all controls, gas pressure regulator and gas cut-off valve. There shall be no exposed screws or bolts on oven exterior. The interior of oven

38 cavity shall be clear without exposed ducts or stand pipe. Oven to be equipped with solid state ignition system. Sixty (60) minute mechanical timer with electric buzzer as standard. Burners in each section shall be removable dual tube, rated at 55,000 BTU per oven section. Air mixtures shall have adjustable air shutters. Oven furnished with gas pressure regulator. Each oven section shall be equipped with two (2) speed 1/3 HP motor blower with automatic thermal overload protection; with two (2) each 50 watt oven lamps; main power switch; light switch; blower switch; door interlock switch. Standard oven to be wired for 115 VAC single phase, and furnished with cord set. Oven to be AGA and NSF approved. To be Blodgett model DFG-100 or approved equal. TN-042A OVEN, GAS, SINGLE CONVECTION WITH PLAIN DOORS Some as TN-41A. Blodgett Model DFG or approved equal

39 Cooking Appliances TN-097 RANGE, GRATE TOP Two burner 34,000 BTU, grate top range with cabinet base, front, both sides, and rear of stainless steel with chrome legs. Stainless steel flue riser with no overhead shelf. Gas supply should be front or rear hook up. Southbend # 164-1, Wolf # FS or approved equal. TN-098 RANGE, GRATE TOP WITH CONVECTION OVEN Four burner grate top range with convection oven with stainless steel front, both sides, and rear, front top rail, and legs. Stainless steel flue riser, with no overhead shelf. Total BTU 112,000. Interior cavity, sides, top and back to be aluminized steel. Oven bottom and door lining to have porcelain enamel finish. Four sides and top of oven to be insulated with heavy, self supporting, block type rock wool. Rack and rack guides: Bright plated, heavy duty, 5 sets of rack guides on 2-3/8" centers with three (3) removable plated racks. Door: Heavy duty construction with extra heavy hinges. Revolutionary single spring and chain device for easy adjustment, positive door catch, and stainless steel mesh silicone impregnated door seal. Blower fan and motor: 1/4 HP, 1725 rpm, 60 C, 115 VAC, high efficiency permanent split phase motor with permanent lubricated ball bearings, overload protection and Class B insulation. Motor mounted to rear of oven. Motor serviceable from front of oven through oven cavity. Electrical system: Wired for single phase, 115 VAC with fused control circuit. Six (6) ft. cord and three (3) prong grounded plug supplied. Gas control system: Includes redundant solenoids, pressure regulator, flame switch safety, pilot filter, pilot adjustment, and manual oven service shut off valve. Electronic ignition: Is high voltage, spark type igniter with flame switch safety device. Electronic ignition is activated by Oven Power On Switch, thus igniting standing pilot. With Oven Power Switch in off position, the gas supply to the oven is completely shut off. Gas supply should be front and rear hook up. Operates on 115 V system (for 208 /236 V, system incorporates a reducing transformer). In case of electronic ignition failure, oven can be operated by manually lighting the pilot. Oven heating: Aluminized steel bar burner, split fan recirculates heat directly from combustion area and within oven cavity. Controls: Located in slide out drawer. Controls include: Power switch - controls power to oven; Fan switch - two position, on for normal operation, on for forced cool down; Thermostat - adjustable for 150 F to 500 F temperature range; Oven ready light - cycles with oven burner. Control drawer cooling system: Located at rear of range. Automatic activation at 150 F. Blower runs continuously until temperature inside control drawer drops to 135 F. Operates independent of power switch. Southbend model P32A-XX Platinum Series, or approved equal. Pg. 26

40 TN-100 PAN, BRAISING Gas fired 30 gallon tilting fry pan, with SPS-FBSM faucet assembly, polished stainless steel pan body shall have exterior dimensions not more than 36" W x 37" front to back, with no clearances required at left side or rear; faucet requires 4' on right side. Interior dimensions of 32" W x 23-2/3" to 24" front to back, and 9" to 11-1/2" deep. Cooking surface shall be 5/8" thick stainless steel, beaded for easy cleaning. Burners shall turn off automatically when skillet is raised to a tilting position. Skillet shall be provided with a one piece stainless steel counter balanced cover. Controls shall consist of an on/off switch, thermostat knob, a signal light to indicate when power is on, a light to indicate temperature cycling, and an indicator of heat conditions, all recessed to avoid breakage. Automatic thermostat shall control temperature from 100 F. to 425 F. Skillet shall tilt 91 under positive control by turning crank, and shall be provided with a PCS pan carrier, removable without the use of tools and designed to eliminate splashing by holding pan in horizontal position not more than 2" from skillet lip throughout tilting operation. Front of skillet shall be sloped forward to allow gravity transfer of food. Shall be equipped with four (4) stainless steel legs with level adjustable bullet feet in the front, with rear feet flanged for bolting. Two (2) year warranty, parts and labor. Cleveland #SGL-30-T or approved equal. TN-106 TWO COMPARTMENT FORCED CONVECTION STEAMER ON 24 INCH CABINET BASE Two compartment convection steamer on a 24" wide cabinet base. Each compartment supplied with four convection generators producing turbulent steam at atmospheric pressure. Compartments to be stainless steel with removable stainless steel wire racks to accommodate standard cafeteria pans. Control panel to operate in timed or manual mode. Mechanical timer from 0 to 60 minutes. Unit equipped with steam purifier, continuous venting vacuum exhaust, steam condenser, pressure switch, automatic safety valve and stainless steel drain screen. Exterior to be stainless steel #4 finish, equipped with two piece air insulated stainless steel doors. Doors may be opened or closed at any time without interruption of cooking cycle. Gas steam generator shall be copper jet tube type, ASME, N.B., and A.G.A. listed with a maximum of 200,000 BTU input. Steam generator, boiler, to be nickel plated. To have visual water level gauge, 115 V control for water level, low water cut off and adjustable pressure switches. Boiler equipped with automatic blow down at shut off including a built in power flush system to assure evacuation of drain valve. Boiler to have secondary low water cut off (as per California code). Unit to require one water connection. Two (2) year warranty, parts and labor. Cleveland model 24-CGM 200 or approved equal

41 Cooking Appliances TN-106A STEAMER, WITHOUT BOILER 14 gauge reinforced stainless steel steamer cavity Insulated cavity and double panel door Heavy refrigeration style door handle with magnetic latch and quick vacuum release system Front mounted manual water reservoir drain valve Left side mounted control panel with smudge resistant overlay Removable stainless steel pan racks provided and positioned to support 21 2, 4 or 6" deep steamer pans Steamer to be NSF Listed as both steamer & holding cabinet Steamer to be U.L. Listed Note: Steamers and Stands should come from the same vendor. TN-106B STEAMER STAND (FOR TN-106A) Stainless steel floor stand that will accommodate either one (1) or two (2) steamer units; with adjustable bullet feet. Must be UL and NSF listed. Stand for Intek XS , or approved equal. Picture shown above Note: Steamers and Stands should come from the same vendor. TN-590 Steamer Fast cook times with Steam Vector Technology Steam Vector utilizes no moving parts Simple Water and Drain Connection No Water Filtration or Treatment required Super Duty Heater Configuration Operating instructions on door in English and Spanish NSF listed, variable temperature hold mode Door can be opened at any time during cooking cycle Steamer cavity made of durable reinforced 14 ga. 304 stainless steel Pg. 28

42 5 power cord with plug included Front mounted drain valve Easy to use Digital Controls Cook and Hold Modes Digital Temperature display Low water, High water and Overtemp indicator lights Field Reversable, Slammable Door 208 volt Accutemp E6 or approved equal TN-590a Stand for TN-590 Steamer Stainless steel floor stand that will accommodate either one or two steamer w/adjustable bullet feet. Must be UL and NSF listed TN-155 OVEN, ELECTRIC, COOKING AND HOLDING Two (2) separately controlled oven compartments; Overall dimensions: 22-1/2" W x 70" H; 22 gauge stainless steel exterior, two 18 gauge doors; stainless steel wire shelves, side racks and drip pans, removable for cleaning; one (1 ) set of bumper guards, one (1) set 5" heavy duty stainless steel castors, 2 rigid, 2 swivel with brake. Oven control features two (2) on /off switches, two (2) cook thermostats 100 F. to 325 F., two (2) holding thermostats 60 F. to 200 F., two (2) - twelve hour cooking timers, two (2) cooking indicator lights, and two (2) holding indicator lights. Alto Shaam Model 1000TH-1/HD or approved equal

43 Laundry, Warewashing & Hot Water Laundry, Warewashing & Hot Water TN-007 WASHER, CLOTHES Top loading; 18 pound capacity; approximately 27" W x 25" D x 43-1/2" H; porcelain cabinet and tub; single speed; three wash cycles; three water level selections; three wash/rinse temperature combinations; damp dry spin at approximately 600 rpm; unbalance load control; permanent lubrication on all friction parts; 115 V, 60 C, single phase; 8 amp; standard plug to meet City of Houston Building Code; 1/2 HP motor with overload protector and automatic reset; white only. One (1) year parts and labor warranty. General Electric WWA GWH, Roper RAX6144E or approved equal. TN-007A DRYER, CLOTHES Approximately 27" W x 25" D x 43 1/2" H; Standard capacity; porcelain top and drum, other areas of acrylic enamel or porcelain; 1/4 HP motor; permanently lubricated overload protector and automatic reset; four drying temperature selections. 120/240 V, 60 C, single phase; 5000 watts; wiring connection for 30 amp, three (3) wire circuit to meet City of Houston code requirements, six (6) foot cord to be supplied. White only. One (1) year parts and labor warranty. General Electric DDE-5808M, Roper REX4635E or approved equal. TN-007B WASHER/DRYER, STACKABLE Approximately 34-5/8" H x 27" D x 27" W; Washer 120 V, 60 C, single phase; Dryer - 120/230 V, 60 C, single phase, six (6) foot cord to be supplied. White only. One (1) year parts and labor warranty. Gibson Stackmasters, Washer model WS27M6WT, Dryer model DE27S6WT; Whirlpool model GTE6234 or approved equal. Pg. 30

44

45 Laundry, Warewashing & Hot Water TN-037 DISPOSER (2 HP) Water-cooled, totally enclosed 2 HP motor protected by air seal; 115 V, 60 C, single phase or 208/240 V, 60 C, single or three phase; 8" shredder of precision ground steel; 8" rotor of wear resistant, hardened carbide material; molded mounting collar with stainless steel clamps; paint free, heat treated corrosion resistant alloy housing; adapter ring and leg support. One (1) year parts and labor warranty. Salvajor II Model 200 or approved equal. Note: Dealer must stock all voltages for immediate delivery. Refer to TN-45 & 46 Dishwashing Assembly to locate installation. TN-037A DISPOSER (1 HP) Water cooled, totally enclosed 1 HP motor protected by air seal; 115 V, 60 C, single phase or 208/240 V, 60 C, single or three phase; 8" shredder of precision ground steel; 8" rotor of wear resistant, hardened carbide material; molded mounting collar with stainless steel clamps; paint free, heat treated corrosion resistant alloy housing; adapter ring and leg support. One (1) year parts and labor warranty. Salvajor II Model 100 or approved equal. Note: Dealer must stock all voltages for immediate delivery. TN-037B DISPOSER (3 HP) Water cooled totally enclosed 3 HP motor protected by air seal; 460 V, 60 C, three phase; 7" throat 8" rotor of wear resistant, hardened carbide material; molded mounting collar with stainless steel clamps; paint free, heat treated corrosion resistant alloy housing; vinyl adapter ring and leg support included. Red Goat Model A3P-R7HC or approved equal. Note: Modification Package to replace scrap sinks to be purchased with the TN-037B above: 7" Vinyl silver trap scraping ring; 3 lbs Model #06- ABC-577 and 18" S/S Con happer less inlet valve 7 lbs. Model #30- ABC-187. Pg. 31

46 TN-039 BOOSTER HEATER, 15 kw Hot water booster heater with 16 gallon storage capacity. All exterior surfaces are to be stainless steel, front panel, easily removable to permit service from the front of unit. Unit to be factory pre-wired and pre-plumbed with calibrated immersion thermostats and high temperature limit switch. Unit to include Castone Tank with 10 year warranty, temperature pressure relief valve, pressure reducing valve, two temperature/pressure gauges, and low water cut off. Unit to be on 6" stainless steel legs. Unit to have pilot light and on/off switch; 208/240/480, 60 C, single or three phase. To be UL and NSF approved. Needs to have stainless steel outer skin and bottom. Also booster should have stainless steel angle frame with welded legs that it sits on. Hatco Model SC-15 or approved equal. TN-039A BOOSTER HEATER, 24 kw Needs to have stainless steel outer skin and bottom. Also booster should have stainless steel angle frame with welded legs that it sits on. Hatco SC-24 TN-039B BOOSTER HEATER, 30 kw Needs to have stainless steel outer skin and bottom. Also booster should have stainless steel angle frame with welded legs that it sits on. Hatco SC-30 TN-039C BOOSTER HEATER, 40 kw Needs to have stainless steel outer skin and bottom. Also booster should have stainless steel angle frame with welded legs that it sits on. Hatco SC-40 Note: Dealer must stock one (1) unit at all times for immediate delivery. TN-040 BOOSTER HEATER, 45 kw Needs to have stainless steel outer skin and bottom. Also booster should have stainless steel angle frame with welded legs that it sits on. Hatco SC-45 Note: Dealer must stock one (1) unit at all times for immediate delivery. - Pg. 32

47 Laundry, Warewashing & Hot Water TN-102 WATER HEATER, LARGE A.S.M.E. construction heater with NSF stand. Five (5) year tank warranty. SUF NEA Note: Dealer must stock one (1) unit at all times for immediate delivery. Note: After June 1, 2002 new no nox codes changed. TN-102A Water heater, Large NOx emissions POLYSHIELD polymer-lined tank with 5-year warranty, threeyear scale failure warranty and one-year cost-free service policy ASME stamped PVI or approved equal TN-102B Water Heater 97% thermal efficiency Load matching modulation 316L stainless steel tank cupronickel/ Stainless steel combustion chamber Heat Transfer (Phoenix) or approval equal Pg. 33

48 TN-103 BOILER, WATER, LARGE WITH PUMP The unit(s) shall be design certified to comply with the current edition of the Harmonized ANSI Z21.13 / CSA 4.9 Standard for Gas-Fired Low Pressure Steam and Hot Water Heaters. The unit(s) shall be designed and constructed in accordance with the ASME Heater & Pressure Vessel Code, Section IV requirements for 160 psi (1103 kpa) working pressure. The water tube heat exchanger shall be a straight tube design with 5/8" (16mm) inner diameter integral finned copper tubes. The tubes shall be rolled directly into ASME glass lined headers rated for 160 psi (1103 kpa) working pressure. The heat exchanger shall be a low water volume design. All gaskets shall be non-metallic, outside the jacket, and separated from the combustion chamber to eliminate deterioration from heat. Headers shall have covers permitting visual inspection and cleaning of all internal surfaces. Boiler shall be design-certified for outdoor use as is, and indoor use with the addition of an external draft hood. The unit shall be designed for Category 1 venting with standard B-vent. The piping side header shall have removable flanges to facilitate maintenance and permit vertical removal of complete heat exchanger for service or replacement. Unit shall have removable burner tray assembly for ease of inspection and maintenance. The units shall use an intermittent electronic ignition with electronic flame supervision, which responds in less than 0.8 seconds upon flame failure. The control circuit shall be 24V. Unit shall be 120V, single phase, 12 Amps. Burners shall be of the atmospheric type and constructed of stainless steel. The combustion chamber shall be lined with a cast refractory of at least two inches (50.8mm) in thickness to retain heat, and approved for service temperatures of not less than 2000 F (1093 C). The outer jacket shall be a unitized shell finished with acrylic thermo-set paint baked at not less than 325 F (163 C). The frame shall be constructed of galvanized steel for strength and protection. Boiler shall have an integral base for placement on combustible surfaces. Boiler gas train shall be for ON/OFF or TWO-STAGE or MECHANICAL MODULATION (models 325 & 400 only) firing. Boiler shall include as standard equipment the following controls and trim: Spark ignition with 100% lockout Water flow switch Operating valve / pressure regulator Redundant safety gas valve Manual gas shut-off valve Temperature and pressure gauge Manual reset high limit 115/24 VAC power from class 2 transformer 75 psi (517 kpa) A.S.M.E. pressure relief valve Raypak, Laars or approved equal Note: After June 1, 2002 new no nox code changed. TN-104 STORAGE TANK, HOT WATER For horizontal or vertical installation. A. 0. Smith Model T A.S.M.E., or approved equal. - Pg. 34

49 Holding & Serving Holding & Serving TN-068 SERVING UNIT, PORTABLE, SELF CONTAINED Portable, Self Contained Serving Unit. 90" high x 74-¼" wide x 29-¾" deep; constructed of one piece seamless double-well polyethylene with entire base of cart completely filled with expandable polyurethane foam for insulation and structural strength. Holding areas are to include: Three (3) on top and three (3) underneath, right and left top holding areas to be 15-1/8" x 22-1/8" x 6". Middle top area to be 12-1/8" x 19-15/16" x 6" and able to hold one (1) each full size 6" pan. Right and left bottom holding areas to be 21" x 26" x 14-5/8" with ability to hold two (2) each 6" full size pans, three (3) each 4" pans or four (4) each 2" pans. Each area to have door with gasket and two (2) latches to ensure air-tight closing. Each door to have removable vent cap and to open 270 degrees to side wall. Middle bottom section must hold one (1) each cash drawer and cash box or hold up to three (3) each 2" full size pans. Cart shall have four (4) each 8" heavy duty swivel casters with brakes mounted in metal plates molded into the cart. Accessories to be included: one (1) color coordinated removable umbrella, with 6 panels, 6 foot in diameter; one (1) removable menu board with erasable surface; one (1) standard cash box and vacuum formed tray specially designed to hold the cash box; one (1) each reversible front panel with color coordinated printing to say Campus Cuisine ; one (1) side blank, white on the opposite side. Color selections to be available: red, blue, black, and green. Cambro Camcruiser or approved equal. TN-068K SERVING LINE, PORTABLE, KIOSK Serving line to consist of two (2) - six well serving unit (Camkiosk No. KVC 856C or approved equal), two (2) - flat or bridge unit (Camkiosk No. KMC24 or approved equal), one (1) - cashier stand (Camkiosk No. KWS40 or approved equal). Accessories to include: four (4) - well covers (Camkiosk No. CB1220 or approved equal), four (4) - cold pack units (Camkiosk No. CP1220 or approved equal), twelve (12) - hot pack units (Camkiosk No. 212HP or approved equal), one (1) - sink (Camkiosk No. KSC402 or approved equal), all serving units to come equipped with stainless steel tray rail pre-mounted (Atlas SLS or approved equal), construction: To be double wall polyethylene with expandable polyurethane foam insulation for structural strength. Each six well unit to have a canopy and menu board, two storage compartments each to hold 8 full size 4" pans. One lockable dry storage area and cash drawer. All units to come with casters. Specify from available colors: granite gray no. 191, granite green no. 192, granite red no. 193, granite sand no. 194, navy blue no. 186, hot red no. 158, green no Specify from canopy colors available : beige no. 157, green no Cambro Kiosk or approved equal. Pg. 35

50 TN-069 SERVING UNIT, COLD, WITH DOUBLE OVERSHELF 46-1/2" L x 27" D x 35" H; 16 gauge stainless steel top; all corners heliarc welded, ground and polished; top opening to receive one self-contained mechanical cold pan for three 12" x 20" x 4" pans; 18 gauge stainless steel 4-1/2" inner liner; all corners to be coved with a minimum of 1/4" radius; 1" insulation on sides; 1-1/2" insulation on bottom; outer case of 22 gauge galvanized steel; embossed lugs along inner surface of top frame to retain removable separator channels; solid vinyl gasket under bead edge to form seal; entire unit to be removable without tools; cold wall method of refrigeration using one (1) 1/4 HP, 120 V, 60 C, single phase, Coplematic condenser; R-22 refrigerant; double deck display case 23" H x 20" D; two (2) safety glass shelves, each with adjustable sneeze guard; full length 10" W stainless steel work shelf on server side with 10" marine edge on two long sides; 10" W full length stainless steel dish shelf 8" under work shelf; body frame of 1-1/4" square stainless steel tubing, all welded construction, ground and polished; front panel of laminate on aluminum; one (1) end panel of laminate on aluminum; 5" diameter, non-marking, gray tired, J & J stainless steel hub swivel castors or stainless steel legs with adjustable leveling feet; solid inverted "V" 12" W stainless steel folding tray slide for easy folding and/or removal. NSF approved. Specify left or right end panel as observed from operator side and castors or legs at time of order. Atlas Metal Industries CWF series, Atlas TN069DA, Moduserv TN069DB, or approved equal. TN-069A SERVING UNIT, COLD, SINGLE OVERSHELF WITHOUT LIGHTS 46-1/2" L x 27" D x 35" H; 16 gauge stainless steel top; all corners heliarc welded, ground and polished; top opening to receive one self-contained mechanical cold pan for three 12" x 20" x 4" pans; 18 gauge stainless steel 4-1/2" inner liner; all corners to be coved with a minimum of 1/4" radius; 1" insulation on sides; 1-1/2" insulation on bottom; outer case of 22 gauge galvanized steel; embossed lugs along inner surface of top frame to retain removable separator channels; solid vinyl gasket under bead edge to form seal; entire unit to be removable without tools; cold wall method of refrigeration using one (1) 1/4 HP, 120 V, 60 C, single phase, Coplematic condenser; R-22 refrigerant; single deck display case 23" H x 20" D; one (1) glass shelf with adjustable sneeze guard without lights; full length 10" W stainless steel work shelf on server side with 10" marine edge on two long sides; 10" W full length stainless steel dish shelf 8" under work shelf; body frame of 1-1/4" square stainless steel tubing, all welded construction, ground and polished; front panel of laminate on aluminum; one (1) end panel of laminate on aluminum; 5" diameter, non-marking, gray tired, J & J stainless steel hub swivel castors or stainless steel legs with adjustable leveling feet; solid inverted "V" 12" W stainless steel folding tray slide for easy folding -

51 Holding & Serving and/or removal. NSF approved. Specify left or right end panel as observed from operator side and castors or legs at time of order. Atlas TN-069AA CWF series, Moduserv 069AB, or approved equal. TN-069SS SERVING UNIT, COLD, WITH DOUBLE TIER DISPLAY STAND, STAINLESS STEEL SURFACE 50" L X 28-1/4" W X 36", 14 gauge 304 stainless steels #4 finish top with all corners welded, ground and polished- Framing to be 16 gauge 304 stainless steal bottom channels and 16 gauge 304 stainless steel 1-1/4" square tubing top members. End panels to be 16 gauge 304 stainless steel. Undershelf to be 18 gauge 304 stainless steel 2" deep with integral 18" high end panels and 6" high rear panel. Unit mounted on 5" diameter heavy duty polyurethane S3 castors with brake models on operator's side. Double tier display unit to have 16 gauge 304 stainless steel #4 finish shelves mounted on 16 gauge stainless steel 1-1/4" square tubing posts. 1/4" thick clear plate glass fixed sneeze guard with 8" clear pass through opening. Each shelf complete with fluorescent light fixtures and safety shields pre-wired to switch in apron of base unit. Display shelves to be 1/4" stainless steel surface material. Drop in cold pan to accommodate trims 12" x 20" x 4" deep pans. Interior liner to be 16 gauge 304 stainless steel fully welded, ground and polished. 18 gauge galvanized jacket over 1" thick side insulation and 1-1/2" thick bottom insulation. Cold wall construction utilizing 1/3 HP 120V single phase COPLEMETIC condensing unit expansion valve metering device and pressure control. Entire cold pan assembly to be removable without use of tools. Pg. 36 Fold down trayslide to be 1/2" thick stainless steel surface material with 2" drop edge on front and ends. Three 1/4 high stainless steel half round bar tray glides attached to stainless steel surface material. Front panel to be 14" thick removable stainless steel surface material. Single point electrical connection with 6' long cord and cap NEMA 5-15P 120V single phase 10.0A. MOD-U-SERVE Model No. MCT-CF3, MOD-U-SERVE 069SSB, Atlas 069SS A, or approved equal. TN-070 SERVING UNIT, HOT ALL SPECIFICATIONS REMAIN THE SAME EXCEPT REPLACE THE WORD HELIARC WITH THE INITIALS TIG, AND ADD BOLTS AND SCREWS TO THE LIST OF ITEMS TO BE SUPPLIED IN STAINLESS STEEL. TN-070CSS SERVING UNIT, HOT, WITH SINGLE TIER SERVING SHELF, THREE PAN UNIT, STAINLESS STEEL SURFACE 50" L x 28 ½" W x 36" H. 14 gauge 304 stainless steel #4 finish top with all corners welded, ground and polished. Framing to be 14 gauge 304 stainless steel bottom channels and 16 gauge 304 stainless steel 1 1/4" square tubing top members. End panels to be 16 gauge 304 stainless steel.

52 Undershelf to be 16 gauge 304 stainless steel 2" deep with integral 18" high end panels and a 6" high rear panel. Unit mounted on 5" diameter heavy duty polyurethane casters with brake models on operators side. Single tier serving shelf to have 16 gauge 304 stainless steel #4 finish shelf mounted on 16 gauge stainless steel 1-1/4" square tubing posts. 1/4" Thick clear plate glass fixed sneeze guard with 8" clear pass through opening. Shelf complete with fluorescent light fixture and safety shield pre-wired to switch in control panel of base unit. Unit provided with three 12" x 20" electrically heated drop in hot food units. Each unit to be 240 volt 1200 watt single phase heating elements with individual infinite controls mounted in common control panel. Fold down tray slide to be 1/2" thick stainless steel surface material with 2" drop edge on front and ends. Three 1/4" high stainless steel half round bar tray glides attached to stainless steel surface material. Front panel to be 1/4" thick removable stainless steel surface material. Single point electrical connection with 6 long cord and cap NEMA p 120/208 volt single phase 19.4 amps. MOD-U-SERVE MCT-HF3, MOD-U- SERVE TN070CSSB, Atlas TN 070CSSA, or approved equal. TN-070ESS SERVING UNIT, HOT, WITH SINGLE TIER SERVING SHELF, FIVE PAN UNIT, STAINLESS STEEL SURFACE 78" L x 28 ½" W x 36" H. 14 gauge 304 stainless steel #4 finish top with all corners welded, ground and polished. Framing to be 14 gauge 304 stainless steel bottom channels and 16 gauge 304 stainless steel 1 1/4" square tubing top members. End panels to be 16 gauge 304 stainless steel. Undershelf to be 16 gauge 304 stainless steel 2" deep with integral 18" high end panels and a 6" high rear panel. Unit mounted on 5" diameter heavy duty polyurethane casters with brake models on operators side. Single tier serving shelf to have 16 gauge 304 stainless steel #4 finish shelf mounted on 16 gauge stainless steel 1-1/4" square tubing posts. 1/4" Thick clear plate glass fixed sneeze guard with 8" clear pass through opening. Shelf complete with fluorescent light fixture and safety shield pre-wired to switch in control panel of base unit. Unit provided with five 12" x 20" electrically heated drop in hot food units. Each unit to be 240 volt 1200 watt single phase heating elements with individual infinite controls mounted in common control panel. Fold down tray slide to be 1/2" thick stainless steel surface material with 2" drop edge on front and ends. Three 1/4" high stainless steel half round bar tray glides attached to stainless steel surface material. Front panel to be 1/4" thick removable stainless steel surface material. Single point electrical connection with 6 long cord and cap NEMA l14-30p 120/208 volt single phase 19.4 amps. MOD-U-SERVE MCT-HF5, MOD-U- SERVE TN070ESSB, Atlas TN070ESSA, or approved equal. TN-071C SERVING UNIT, FLAT TOP, THREE PAN SIZE 46-1/2" L x 27" W x 35" H; top of 16 gauge stainless steel, all corners heliarc welded, ground and polished; 10" W stainless steel work shelf entire length of unit on operator side with 1/2" marine edge on rear long side and tray stop to operator's left; full length stainless steel removable under shelf; body frame construction of 1-1/4" square stainless steel tubing, all welded, ground and polished; front panel of laminate on aluminum; 5" diameter, non-marking, gray tired, J & J stainless steel hub swivel castors or stainless steel legs with adjustable leveling feet; solid inverted "V" 12" W stainless steel folding tray slide for easy folding and/or removal; NSF approved. Specify castors or legs at time of order. Atlas Metal Industries Model CWFT 3, Atlas TN071CA, MOD-U- SERV TN071CB, or approved equal. -

53 Holding & Serving TN-071D Pg. 37 Pg. 37 SERVING UNIT, FLAT TOP, FOUR PAN SIZE 60-1/4" L x 27" W x 35" H; top of 16 gauge stainless steel, all corners heliarc welded, ground and polished; 10" W stainless steel work shelf entire length of unit on operator side with 1/2" marine edge on rear long side and tray stop to operator's left; full length stainless steel removable under shelf; body frame construction of 1-1/4" square stainless steel tubing, all welded, ground and polished; front panel of laminate on aluminum; 5" diameter, non-marking, gray tired, J & J stainless steel hub swivel castors or stainless steel legs with adjustable leveling feet; solid inverted "V" 12" W stainless steel folding tray slide for easy folding and/or removal; NSF approved. Specify castors or legs at time of order. Atlas Metal Industries Atlas TN-071DA, MOD -U-SERV TN - 071DB or approved equal. TN-071E SERVING UNIT, FLAT TOP, FIVE PAN SIZE 74" L x 27" W x 35" H; top of 16 gauge stainless steel, all corners heliarc welded, ground and polished; 10" W stainless steel work shelf entire length of unit on operator side with 1/2" marine edge on rear long side and tray stop to operator's left; full length stainless steel removable under shelf; body frame construction of 1-1/4" square stainless steel tubing, all welded, ground and polished; front panel of laminate on aluminum; 5" diameter, non-marking, gray tired, J & J stainless steel hub swivel castors or stainless steel legs with adjustable leveling feet; solid inverted "V" 12" W stainless steel folding tray slide for easy folding and/or removal; NSF approved. Specify castors or legs at time of order. Atlas Metal Industries Model CWFT 5, Atlas NV071EA, Mod-U-Serv TN071EB, or approved equal. TN-071SS SERVING UNIT, FLAT TOP, THREE PAN UNIT, STAINLESS STEEL SURFACE 50" L x 28-1/2" W x 36" H, 14 gauge 304 stainless steel #4 finish top with all corners welded, ground and polished. Framing to be 14 gauge 304 stainless steel bottom channels and 16 gauge 304 stainless steel 1-1/4" square tubing top members. End panels to be 16 gauge 304 stainless steel. Under shelf to be 16 gauge 304 stainless steel 2" deep with integral 18" high end panels and 6" high rear panel. Unit mounted on 5" diameter heavy duty polyurethane casters with brake model on operators side. Fold down tray slide to be 1/2" thick stainless steel surface material with 2" drop edge on front and ends. Three 1/4" high stainless steel half round bar tray glides attached to stainless steel surface material. Front panels to be 1/4" thick stainless steel surface material. MOD- U-SERVE MCT-FT3, Mod-U-Serv TN071SSB, Atlas TN071SSA, or approved equal. TN-071X SERVING UNIT, FLAT TOP, SMALL 32-3/4" L x 27" W x 35" H; top of 16 gauge stainless steel, all corners heliarc welded, ground and polished; 10" W stainless steel work shelf entire length of unit on operator side with 1/2" marine edge on rear long side and tray stop to operator's left; full length stainless steel removable under shelf; body frame construction of 1-1/4" square stainless steel Pg. 38

54 tubing, all welded, ground and polished; front panel of laminate on aluminum; 5" diameter, nonmarking, gray tired, J & J stainless steel hub swivel castors or stainless steel legs with adjustable leveling feet; solid inverted "V" 12" W stainless steel folding tray slide for easy folding and/or removal; NSF approved. Specify castors or legs at time of order. Atlas Metal Industries, Atlas TN071XA, Mod-U-Serv TN071XB, or approved equal. TN-072 TABLE, CASHIER 32-3/4" L x 27" W x 35" H; press formed 16 gauge stainless steel top; heliarc welded, ground and polished corners; stainless steel cash drawer with keyed lock mounted on stainless steel glides directly under top; body frame of 1-1/4" square stainless steel tubing; all welded construction, ground and polished; laminate on aluminum front panel; 5" diameter, nonmarking, gray tired, J & J stainless steel hub swivel castors or stainless steel legs with adjustable leveling feet; solid inverted "V" 12" W stainless steel folding tray slide for easy folding and/or removal mounted to student side; 10" wide stainless steel work shelf entire length of unit on operator side. NSF approved. Specify direction of student flow as observed from customer side and castors or legs at time of order. Order end panels when stand-alone buffet service is desired TN-118. Atlas Metal Industries CWCS, Atlas TN072A, Mod-U-Serv TN072B, series or approved equal. Right to Left Left to Right TN-072SS TABLE, CASHIER, STAINLESS STEEL SURFACE 27" L x 28-1/2" W x 36" H, 14 gauge 304 stainless steel #4 finish top with all corners welded, ground and polished. Framing to be 14 gauge 304 stainless steel bottom channels and 16 gauge 304 stainless steel 1 1/4" square tubing top members. End panels to be 16 gauge 304 stainless steel. Unit mounted on 5" diameter heavy duty polyurethane casters with brake models on operators side. Cash drawer constructed of 18 gauge stainless steel drawer front, sides and liner pan. Complete with cylinder lock. Counter top complete with removable electrical cord grommet for access to duplex receptacle provided under top. Fold down tray slide to be 1/2" thick stainless steel surface material with 2" drop edge on front and ends. Three 1/4" high stainless steel half round bar tray glides attached to stainless steel surface material. Front panel to be 1/4" thick removable stainless steel surface material. Single point electrical connection with 6 long cord and cap NEMA 5-15p 120 V single phase 10 amp. MOD-U-SERVE Model MCT-CRSG, Mod-U-Serve TN072SSB, Atlas TN072SSA, or approved equal. TN-073 TABLE, CASHIER, LARGE Same as TN-072 except dimensions are 46-1/2" L x 27" W x 35" H. Atlas Metal Industries CWCS series Atlas TN073A, Mod-U-Serve TN073B, or approved equal. Pg. 39 -

55 Holding & Serving TN-082 SERVING UNIT, HOT, SUPER BAR 60-1/4" L x 27" W x 35" H; body frame construction of 1-1/4" x 1-1/4" stainless steel tubing; 16 gauge stainless top, all corners welded, ground and polished; integral locking device to align and retain cart positioning when two or more carts are joined together; panels of.050" aluminum covered with plastic laminate; unless otherwise specified, all panels will be woodgrain. 5" gray tired, J & J stainless steel hub swivel castors, two castors with toe operated brakes or stainless steel legs with adjustable leveling feet; over shelf with Calrod style infrared heat unit, 120 V, 60 C, single phase; 16 gauge stainless steel top with uprights of 3/4" x 3/4" stainless steel tubing, mounted to be removable without the use of tools; stainless steel under shelf; 16 gauge stainless steel solid tray slide with inverted "V"-groove top, mounted with hardware for easy folding and removal. Specify castors or legs at time of order. Atlas Set-N-Serve CWFT-4 cart, OSH-4 over shelf, US-4 under shelf and SLS tray slide, Atlas TN082A, Mod-U-Serve TN082B, or approved equal. TN-085 CABINET, HOT PASS THRU, SUPER BAR 22" W x 30-1/2" D x 67-1/2" H; stainless steel interior and exterior; low heat density output thermal cable; manually adjustable thermostat. All castors should be stainless steel. ; 120 V, 60 C, single phase; 2000 watts; 16.7 amps; three wire cord and plug. One (1) year parts and labor warranty. Alto-Shaam 1000-UPS or approved equal. TN-086 CABINET, HOT, SUPER BAR 22" W x 29-1/2" D x 67-1/2" H; stainless steel interior and exterior; low heat density output thermal cable; manually adjustable thermostat; 120 V, 60 C, single phase; 2000 watts, 16.7 amps; three wire cord and plug. All castors should be stainless steel. One (1) year parts and labor warranty. Alto-Shaam 1000-UP or approved equal. TN-089 WARMER, CHILI, SUPER BAR Hot Food Warmer with 2-11 quart stainless steel insets watts. With 1 oz. ladle and notched lid. Wells #HW 10 or approved equal.

56 TN-110A BUFFET CART, SINGLE WELL Pg. 40 Dimensions: 32-3/4" L x 27" W x 35" H. All welded construction, with ground and polished weld joints. Frame shall be of square 1-1/4" x 1-1/4" stainless steel tubing; with apron and top of 16 gauge stainless steel to be pre-drilled for bolting to uprights. 5" diameter non-marking, gray tired, J & J stainless steel hub swivel castors, fitted with ball bearings in both swivel and axle raceways with access points for proper lubrication; toe operated brakes. Top opening shall be made to receive hot or cold drop-in units. An integral locking device shall be provided on each cart to align and retain cart positioning when two or more modular units are joined. Device shall require no additional joiner strips. Sliding doors on one side. Full stainless steel undershelf. Double solid stainless steel folding tray slides. Panels shall be of formica laminate with finish choices. Unless otherwise specified, all panels will be woodgrain. NSF approved. Specify color of laminate panel at time of order. Order TN- 118 End Panels when stand alone buffet service is desired. Atlas CWF, Atlas TN110AA, Mod-U- Serve TN110AB series or approved equal. TN-110C BUFFET CART, THREE WELL Same as TN-110A except with dimensions of: 46-1/2" L x 27" H W x 35" H. Specify color of laminate panel at time of order, unless otherwise specified, all panels will be woodgrain. Order TN-118 End Panels when stand alone buffet service is desired. Atlas TN110CA, Mod-U-Serve TN110CB TN-110D BUFFET CART, FOUR WELL Same as TN-110A except with dimensions of: 60-1/4" L x 27" W x 35" H. Specify color of laminate panel at time of order, unless otherwise specified, all panels will be woodgrain. Atlas TN110DA, Mod-U-Serv TN110DB. Order TN-118 End Panels when stand alone buffet service is desired. TN-110E BUFFET CART, FIVE WELL Same as TN-110A except with dimensions of: 74" L x 27" W x 35" H. Specify color of laminate panel at time of order. Atlas TN110EA, Mod-U-Serv TN110EB. Order TN-18 End Panels when stand alone buffet service is desired. -

57 Holding & Serving TN - 111B Pg. 41 OVERSHELF, DUAL SERVICE, TWO PAN UNIT All stainless steel construction, welded, ground, and polished. Upright constructed of 3/4" stainless steel square tubing. Sneeze guard furnished with 1/4" clear plexiglass. Use with TN - 110A. Specify configuration: with lights, without lights, or with infrared heat. Note: Cannot be ordered with heat and light. Atlas Metal Industries OSDC, Atlas TN111BA, Mod-U-Serv TN111BB series or approved equal. TN-111C OVERSHELF, DUAL SERVICE, THREE PAN UNIT All stainless steel construction, welded, ground, and polished. Upright constructed of 3/4" stainless steel square tubing. Sneeze guard furnished with 1/4" clear plexiglass. Use with TN-110C. Specify configuration: with lights, without lights, or with infrared heat. Note: Cannot be ordered with heat and light. Atlas Metal Industries OSDC, Atlas TN111CA, Mod-U-Serv TN111CB series or approved equal. TN-111D OVERSHELF, DUAL SERVICE, FOUR PAN UNIT All stainless steel construction, welded, ground, and polished. Upright constructed of 3/4" stainless steel square tubing. Sneeze guard furnished with 1/4" clear plexiglass. Use with TN-110D. Specify configuration: with lights, without lights, or with infrared heat. Note: Cannot be ordered with heat and light. Atlas Metal Industries OSDC series, Atlas TN111DA, Mod-U-Serv TN111DB, or approved equal. TN-111E OVERSHELF, DUAL SERVICE, FIVE PAN UNIT All stainless steel construction, welded, ground, and polished. Upright constructed of 3/4" stainless steel square tubing. Sneeze guard furnished with 1/4" clear plexiglass. Use with TN-110E. Specify configuration: with lights, without lights, or with infrared heat. Note: Cannot be ordered with heat and light. Atlas Metal Industries OSDC series, Atlas TN111EA, Mod-U-Serv TN111EB, or approved equal. Pg. 42

58 TN-113B OVERSHELF, SINGLE SERVICE, ONE OR TWO PAN UNITS Basic construction same as TN-111C, but with single service and two lines of fluorescent lights. Use with TN- 110A. Specify configuration: with lights, without lights, or with infrared heat. Note: Cannot be ordered with heat and light. Atlas Metal Industries OSC series, Atlas TN113BA, Mod-U-Serv TN113BB, or approved equal. TN-113C OVERSHELF, SINGLE SERVICE, THREE PAN UNIT Basic construction same as TN-111C, but with single service and two lines of fluorescent lights. Use with TN-110C. Specify configuration: with lights, without lights, or with infrared heat. Note: Cannot be ordered with heat and light. Atlas Metal Industries OSC series, Atlas TN113CA, Mod-U-Serv TN113CB, or approved equal. TN-113D OVERSHELF, SINGLE SERVICE, FOUR PAN UNIT Basic construction same as TN-111D, but with single service and two lines of fluorescent lights. Use with TN-110D. Specify configuration: with lights, without lights, or with infrared heat. Note: Cannot be ordered with heat and light. Atlas Metal Industries OSC series, Atlas TN113DA, Mod-U-Serv TN113DB, or approved equal. TN-113E OVERSHELF, SINGLE SERVICE, FIVE PAN UNIT Basic construction same as TN-111E, but with single service and two lines of fluorescent lights. Use with TN-110E. Specify configuration: with lights, without lights, or with infrared heat. Note: Cannot be ordered with heat and light. Atlas Metal Industries OSC series, Atlas TN113EA, Mod-U-Serv TN113EB, or approved equal. Pg. 43 -

59 Holding & Serving TN-114A HOT PAN DROP-IN, SINGLE PAN Self-contained electric heated steam pan with one (1) 12" x 20" openings; steam pans must be riveted or screwed and not welded to support. Additional pans must be available as parts. The unit shall have an inner liner of 18 gauge stainless steel, type 304, grade Unit shall be of one piece all welded construction. Stainless steel element holder, insulation pan, brackets, bottom, sides, and screws; all corners coved with a minimum of 1/4" radius. Insulation shall be fiberglass of 1-1/2" minimum thickness. There shall be a minimum of 1000 watts of heat per element, 208 V or 240 V, 60 C, single phase. The outer case shall be of 22 gauge stainless steel. The top shall be 18 gauge stainless steel, die pressed with a raised bead edge around the entire perimeter. There shall be a solid vinyl gasket under the bead edge to form a seal preventing seepage or marring of other equipment. The unit shall have embossed mounting lugs along inner surface of top frame to retain removable separator channels. The entire unit shall be removable from it's mounting without the use of tools. The unit shall be equipped with a 6 ft. long power cord. This unit shall be compatible with TN-110A. Specify 208 V or 240 V at time of order. Atlas TN114AA, Mod-U-Serv TN114AB, or approved equal. TN-114C HOT PAN DROP-IN, THREE PAN Same as TN-114A except with three (3) 12" x 20" openings. This unit shall be compatible with TN- 110C. Specify 208 V or 240 V at time of order. Atlas TN114CA, Mod-U-Serv TN114CB, or approved equal. Pg. 44

60 TN-114D HOT PAN DROP-IN, FOUR PAN Same as TN-114A except with four (4) 12" x 20" openings. This unit shall be compatible with TN-110D. Specify 208 V or 240 V at time of order. Atlas TN114DA, Mod-U-Serv TN114DB, or approved equal. TN-114E HOT PAN DROP-IN, FIVE PAN Same as TN-114A except with five (5) 12" x 20" openings. This unit shall be compatible with TN-70 or TN-110E. Specify 208 V or 240 V at time of order. Atlas TN114EA, Mod-U-Serv TN114EB, or approved equal. TN-115C ICE PAN DROP-IN, THREE PAN The unit shall have an inner liner of 18 gauge stainless steel, type 304, grade 18-8, with capacity to hold three (3) standard 12" x 20" pans with adapters. Unit shall be of one piece all welded construction. All corners shall be coved with a minimum of 1/4" radius. Insulation shall be 1" thick on sides and 2" thick on bottom. The outer case shall be of 22 gauge galvanized steel. The top shall be of 18 gauge stainless steel die pressed with a raised bead edge around the entire perimeter. There shall be a solid vinyl gasket under the bead edge to form a seal, preventing seepage or marring of other equipment. The unit shall have embossed mounting lugs along inner surface of top frame to retain removable separator channels. The entire unit shall be removable from mounting without the use of tools except when permanent plumbing is required. For use with TN-110C. Two (2) year parts and Labor. Atlas TN115CA, Mod-U-Serv TN115CB, or approved equal. TN-115D ICE PAN DROP-IN, FOUR PAN Same as TN-115C except with capacity to hold four (4) standard 12" x 20" pans with adapters. This unit shall be compatible with TN-110D. Two (2) year parts and labor. Atlas TN115DA, Mod-U-Serv TN115DB, or approved equal. Pg. 45 -

61 Holding & Serving TN-115E ICE PAN DROP-IN, FIVE PAN Same as TN-115C except with capacity to hold five (5) standard 12" x 20" pans with adapters. This unit shall be compatible with TN-110E. Two (2) year parts and Labor. Atlas TN115EA, Mod-U-Serv TN115EB, or approved equal. TN-117C SNEEZE GUARD, DOUBLE DECK, THREE PAN UNIT Double deck display constructed of 5/8" x 5/8" stainless steel tubing, welded, ground and polished. 1/4" safety glass removable shelves with adjustable stainless steel sneeze guard frame. Atlas DD - 3 series. Atlas TN117CA, Mod-U- Serv TN117CB, or approved equal. TN-117D SNEEZE GUARD, DOUBLE DECK, FOUR PAN UNIT Basic construction same as TN-117C. Atlas DD - 3 series. Atlas TN117DA, Mod-U-Serv TN117DB, or approved equal. TN-117E SNEEZE GUARD, DOUBLE DECK, FIVE PAN UNIT Basic construction same as TN-117C. Atlas DD - 3 series. Atlas TN117EA, Mod-U-Serv TN117EB, or approved equal. TN-118 END PANEL, LAMINATE COVERED Dimensions: 22-1/4" W x 26-1/4" H, to fit in end opening of TN-72, TN-110A, TN-110C, TN-110D, TN-110E, Plastic laminate on aluminum. Specify cart matching color at time of order. Unless otherwise specified, all panels will be woodgrain. Atlas EP, Atlas TN118A, Mod-U-Serv TN118B, or approved equal.

62 TN-119 ADAPTER PLATE, TWO HOLE 8-1/2" INSERTS Pg. 46 Adapter plate with dimensions: 13" W x 21" L, to fit standard 12" x 20" pan opening with two 8-1/2" insert openings. Fabricated of 18 gauge stainless steel with beaded edge. Atlas AD-28, Atlas TN119A, Mod-U-Serv TN119B, or approved equal. TN-120C REFRIGERATED DROP-IN, THREE PAN A completely self contained R-22, pre-charged and wired refrigerator unit designed to use three (3) standard 12" x 20" pan with adapters, inner liner of 18 gauge stainless steel, type 304, grade 18-8 one piece all welded construction, corners coved with a minimum of 1/4" radius, insulation shall be 1" on sides and 1-1/2" on bottom; outer case of 22 gauge galvanized steel, embossed mounting lugs along inner surface of top, to retain removable separator channels. Solid vinyl gasket under the bead edge to form a seal, compressor housing fabricated from formed angles and bolted in a rigid form. Entire unit shall be removable from mounting without the use of tools. 120 V, 60 C. This unit shall be compatible with TN-110C. Atlas WCM, Atlas TN120CA, Mod-U-Serv TN120CB, or approved equal. Two (2) parts and labor. TN-120D REFRIGERATED DROP-IN, FOUR PAN Same as TN-120C except with four (4) standard 12" x 20" pans with adapters. This unit shall be compatible with TN- 110D. Two (2) parts and labor. Atlas TN120DA, Mod-U- Serv TN120DB, or approved equal. TN-120E REFRIGERATED DROP-IN, FIVE PAN Same as TN-120C except with five (5) standard 12" x 20" pans with adapters. This unit shall be compatible with TN-110E. Two (2) parts and labor. Atlas TN120EA, Mod-U-Serv TN120EB, or approved equal. - Pg. 47

63 Holding & Serving TN-121 CABINET, HOT, FOOD TRANSPORT/SERVICE 36" H x 27 ½" D x 18 ¼" W. Top serve cabinet of nickel bearing type 304 stainless steel, 20 gauge polished exterior, 24 gauge interior wall; full 1" thick high density fiberglass insulation in cabinet and door. Door to be full length double wall stainless, heavy duty flush mounted latches, concealed hinges, self-closing when opened less than 90 ; beyond 90, door remains open. Pan slides of removable stainless steel, channel type spaced on 2 ¾" centers, maximum inside working depth of 22 ½" to accommodate all standard depth pans. Heating system is stainless, lift out without use of tools using; 120 volts, 60 cycle, single phase, 1500 watts, 13 amps. Ten foot 3 wire rubber cord with 3 prong grounding plug. Accessories to include stainless steel channel close fit bumper with vinyl insert, chest handle ASY pair SS PH - 912, transport latch, and canned heat unit adapter. Carter Hoffman Model # PH TS or approved equal. TN-122 CABINET, HOT, FOOD TRANSPORT/HOLDING 58" H x 29 ½" D x 24" W; Top serve cabinet of nickel bearing type 304 stainless steel, 20 gauge polished exterior, 24 gauge interior wall; full 1" thick high density fiberglass insulation in cabinet and door. Door to be full length double wall stainless, heavy duty flush mounted latches, concealed hinges, self-closing when opened less than 90 ; beyond 90, door remains open. Pan slides of removable stainless steel, channel type, spaced on 2 ¾" centers, maximum inside working depth of 22 ½" to accommodate all standard depth pans. Heating system is stainless steel, lift out without use of tools using; 120 volts, 60 cycle, single phase, 1500 watts, 13 amps. Ten foot 3 wire rubber cord with 3 prong grounding plug. Accessories to include stainless steel channel close fit bumper with vinyl insert, chest handle ASY pair SS PH - 912, transport latch, and canned heat unit adapter. Carter Hoffman Model # PH or approved equal. TN-123 CABINET, HOT, FOOD TRANSPORT Cabinet to transport or store either hot or cold foods; one piece, polyethylene shell filled with thick foam insulation; nylon latch and air-tight gasket; twelve (12) molded-in rails on 1½" centers; door to open 270º; two units are to interlock for stacking or transporting. Overall dimensions 25-¾" X 18-¼" X 24-7/8"; Optional dolly to be available and optional strap to secure two (2) cabinets to be available. Cambro Camcarrier MPC 400, Optional Items: Cambro Camdolly CD400 and Cambro Strap 400STP or approved equal. Pg. 48

64 TN-124B PROTECTOR CASE, WITH PLEXIGLASS SNEEZE GUARD, TWO PAN UNIT All stainless steel construction, welded, ground, and polished. Overall dimensions: 32¼" W x 15¼" H x 12½" D. Top of 16 gauge with uprights constructed of 1" stainless steel square tubing. Sneeze guard furnished with 1/4" clear plexiglass, with 5½" clearance. Use with TN071X. Atlas Metal Industries PRC series, Atlas TN124BA, Mod-U-Serv Tn124BB, or approved equal. TN 124C PROTECTOR CASE, WITH PLEXIGLASS SNEEZE GUARD, THREE PAN UNIT All stainless steel construction, welded, ground, and polished. Overall dimensions: 46" W x 15¼" H x 12½" D. Top of 16 gauge with uprights constructed of 1" stainless steel square tubing. Sneeze guard furnished with 1/4" clear plexiglass, with 5½" clearance. Use with TN071C. Atlas Metal Industries PRC series, Atlas TN124CA, Mod-U-Serv TN124CB, or approved equal. TN 124D PROTECTOR CASE, WITH PLEXIGLASS SNEEZE GUARD, FOUR PAN UNIT All stainless steel construction, welded, ground, and polished. Overall dimensions: 59¾" W x 15¼" H x 12½" D. Top of 16 gauge with uprights constructed of 1" stainless steel square tubing. Sneeze guard furnished with 1/4" clear plexiglass, with 5½" clearance. Use with TN071D. Atlas Metal Industries PRC series, Atlas TN124DA, Mod-U-Serv TN124DB, or approved equal. TN 124E PROTECTOR CASE, WITH PLEXIGLASS SNEEZE GUARD, FIVE PAN UNIT All stainless steel construction, welded, ground, and polished. Overall dimensions: 73½" W x 15¼" H x 12½" D. Top of 16 gauge with uprights constructed of 1" stainless steel square tubing. Sneeze guard furnished with 1/4" clear plexiglass, with 5½" clearance. Use with TN071E. Atlas Metal Industries PRC series, Atlas TN124EA, Mod-U-Serv TN124EB, or approved equal. Pg. 49 -

65 Holding & Serving TN-170C FROSTOP, REFRIGERATED DROP-IN, THREE PAN A completely self contained pre-charged and wired refrigerated cold plate unit of 16 gauge stainless steel, type 304, grade Unit shall be of one piece all welded construction. Top shelf to be insulated with 1 1/2 inch combination of styrofoam and fiberglass. The outer case of 18 gauge galvanized steel. Top frame 18 gauge stainless steel die pressed with a raised bead edge around the entire perimeter with a solid vinyl gasket under the bead edge to form a seal. The compressor housing fabricated from formed angles and bolted in a rigid form. R-22 refrigerant when available. 1/4 HP, 120 Volt, 60 C, Single phase, 4.5 Amps. Mounting without the use of tools, except when permanent plumbing is required. For use with TN-110C. Atlas WF3 series Frostop, Atlas TN170CA, Mod-U-Serv TN170CB, or approved equal. Two (2) parts and labor. TN-170D FROSTOP, REFRIGERATED DROP-IN, FOUR PAN A completely self contained pre-charged and wired refrigerated cold plate unit of 16 gauge stainless steel, type 304, grade Unit shall be of one piece all welded construction. Top shelf to be insulated with 1 1/2 inch combination of styrofoam and fiberglass. The outer case of 18 gauge galvanized steel. Top frame 18 gauge stainless steel die pressed with a raised bead edge around the entire perimeter with a solid vinyl gasket under the bead edge to form a seal. The compressor housing fabricated from formed angles and bolted in a rigid form. R-22 refrigerant when available. 1/4 HP, 120 Volt, 60 C, Single phase, 6 Amps. Mounting without the use of tools, except when permanent plumbing is required. For use with TN-110D. Atlas WF4 series Frostop, Atlas TN170DA, Mod-U-Serv TN170DB, or approved equal. Two (2) parts and labor. TN-170E FROSTOP, REFRIGERATED DROP-IN, FIVE PAN A completely self contained pre-charged and wired refrigerated cold plate unit of 16 gauge stainless steel, type 304, grade Unit shall be of one piece all welded construction. Top shelf to be insulated with 1 1/2 inch combination of styrofoam and fiberglass. The outer case of 18 gauge galvanized steel. Top frame 18 gauge stainless steel die pressed with a raised bead edge around the entire perimeter with a solid vinyl gasket under the bead edge to form a seal. The compressor housing fabricated from formed angles and bolted in a rigid form. R-22 refrigerant when available. 1/3 HP, 120 Volt, 60 C, Single phase, 6 Amps. Mounting without the use of tools, except when permanent plumbing is required. For use with TN-110E. Atlas WF5 series Frostop, Atlas TN170EA, Mod-U-Serv TN170EB, or approved equal. Two (2) year parts and labor. Pg. 50

66 TN-175B TRAY RAIL, TWO WELL CART Tray rail, solid tray slide. Inverted "V" 16 - gauge stainless steel, 32-3/4" L X 12" W for use on serving carts, customer side, Atlas SLS-2, Atlas TN175BA, Mod- U-Serv TN175BB, or approved equal. TN-175C TRAY RAIL, THREE WELL CART Tray rail, solid tray slide. Inverted "V" 16 - gauge stainless steel, 46-1/2" L X 12" W for use on serving carts, customer side, Atlas SLS-3, Atlas TN175CA, Mod-U-Serv TN175CB, or approved equal. TN-175D TRAY RAIL, FOUR WELL CART Tray rail, solid tray slide. Inverted "V" 16 - gauge stainless steel, 60-1/4" L X 12" W for use on serving carts, customer side, Atlas SLS-4, TN175DA, Mod-U-Serv TN175DB, or approved equal. TN-175E TRAY RAIL, FIVE WELL CART Tray rail, solid tray slide. Inverted "V" 16 - gauge stainless steel, 74" L X 12" W for use on serving carts, customer side, Atlas SLS-5, Atlas TN175EA, Mod-U-Serv TN175EB, or approved equal. Pg. 51 -

67 Merchandising TN-180B WORK SHELF,TWO WELL CART Work shelf, solid gauge stainless steel, 32-3/4" L X 8" W, easy folding and/or removal for use on serving cart, operator side. Atlas SH-2, Atlas TN180BA, Mod-U-Serv TN180BB, or approved equal. TN-180C WORK SHELF, THREE WELL CART Work shelf, solid gauge stainless steel, 46-1/2" L X 8" W, easy folding and/or removal for use on serving cart, operator side. Atlas TN180CA, MOD-U-Serv TN180CB, or approved equal. TN-180D WORK SHELF, FOUR WELL CART Work shelf, solid gauge stainless steel, 60-1/4" L X 8" W, easy folding and/or removal for use on serving cart, operator side. Atlas SH-4, Atlas TN180DA, Mod-U-Serv TN180DB or approved equal. TN-180E WORK SHELF, FIVE WELL CART Work shelf, solid gauge stainless steel, 74" L X 8" wide, easy folding and/or removal for use on serving cart, operator side. Atlas SH-5, Atlas TN180EA, Mod-U-Serv TN180EB, or approved equal. Pg. 52

68 Merchandising TN-096 TWIN BEVERAGE DISPENSER, SUPER BAR Jet spray; 16" W x 8-1/2" D x 23-1/4" H; bowl and cover of transparent, unbreakable plastic; five gallon capacity for each bowl; 450 watt; 115 V; 60 C; single phase; three wire cord and plug. Jet Spray TJ-3 or approved equal. TN-130 SANDWICH DISPLAY Heated with lights. 18 gauge non magnetic stainless steel in a 30" polymer enclosed display case accessible from the operator (control) side, as well as the opposite side for self-service. The heated, stainless steel base is controlled by one (1) on/off power switch, one (1) adjustable thermostat with a range of 1 thru 10, and includes one (1) indicator light. Four (4) - 75 watt shatter proof coated bulbs are enclosed in the top of the case and are controlled by one (1) hi/low/off dimmer switch. The case includes four (4) stainless steel dividers, adjustable on 1/2" centers, to provide a total of five (5) sandwich chutes. The case includes one (1 ) set of 1" legs. Panel cover brown; capacity of 25 to 30 sandwiches. Electrical: 125 VAC., 60 H, single phase, 800 watts, 6.4 amps, NEMA 5-15P, 15, 125 V plug. NSF approved. Alto Shaam model 100-HSL/COLUX or approved equal. TN-131 WARMER, LIGHTED DISPLAY Lighted holding cabinet with 22 gauge stainless steel exterior, glass French doors on the control side, and a solid glass panel on the non control side. Six (6) inch stainless steel legs. The cabinet is controlled by an adjustable thermostat from 60 F. to 200 F. with an off position, includes an heat on indicator light, and holding temperature gauge to monitor inside air temperature. The interior of the cabinet is lighted by two (2) 40-watt appliance bulbs, controlled with an on/off switch, Cabinet is furnished with three (3) chrome plated wire shelves, and two (2) chrome plated side racks spaced at 3" centers. Side racks and wire shelves are canted at a 10 degree angle for maximum visibility of product. Electrical: 125 VAC, 60 C, single phase, 1080 watts, 8.6 amps, NEMA5-15PISA, 125 V plug. Alto-Shaam model 750-GDU or approved equal. Pg. 53 -

69 Merchandising TN-132 WARMER, PASS THRU, LIGHTED DISPLAY Pass thru doors. Similar to TN-131. Lighted holding cabinet with 22 gauge stainless steel exterior, with glass French doors on both sides of the cabinet. The side racks and shelves are not angled. Alto Sham Model 750-GDU/PT or approved equal. TN-135 POPCORN POPPER WITH HOLDING UNIT Glass cabinet with metal supports at each corner: 21" D x 21" W x 30-1/2" T. An eight (8) ounce all steel kettle and 250 watt heat lamp to produce one (1) ounce servings per hour using 120 V, 60 C, single phase, 1250 watts, 10.5 amps. Cretors model T-200 or approved equal. TN-145 CABINET, DISPLAY AND HOLD Display and Hold Cabinet with three tier rotating circle pan racks, two door pass through construction, display to be lighted, rated at 1.6 KW, 13.5 Amps, 120 Volts, Single Phase AC, NEMA 5-15P five foot cord set, overall dimensions: 32-1/2" H x 22" W x 22" D, one (1) year warranty on both parts and labor. Savory Equipment model DH-2L number with Merchandising Display theme Pizza #45050 or approved equal. TN-510 ICE DISPENSER, 90 LB. Ice Dispenser with 90 lbs. ice storage, fully insulated ice storage bin to be plastic, exterior cabinet to be 20 gauge type 304 stainless steel with merchandiser/woodgrain/stainless steel front, ice dispensing to result from a paddle wheel which lifts and agitates the ice, ice is controllable dispensed into cups from 8 oz. to 2 liters, eight foot three wire cord and plug, 120 Volt, 60 cycle, single phase, overall dimensions: 15" W x 28" D x 32" H, UL listed and NSF certified. SerVend model M-90, SerVend TN510A, TN510B Booth, or approved equal. Pg. 54

70 ICE DISPENSER, 150 LB. TN-515 Ice Dispenser with 150 lbs. ice storage, fully insulated ice storage bin to be plastic, exterior cabinet to be 20 gauge type 304 stainless steel with merchandiser/woodgrain/stainless steel front, ice dispensing to result from a paddle wheel which lifts and agitates the ice, ice is controllable dispensed into cups from 8 oz. to 2 liters, eight foot three wire cord and plug, 120 Volt, 60 cycle, single phase, overall dimensions: 22" W x 28" D x 32" H, UL listed and NSF certified. SerVend model M-150, SerVend TN515A, TN515B Booth, or approved equal. TN-520 ICE DISPENSER, 220 LB. Ice Dispenser with 220 lbs. ice storage, fully insulated ice storage bin to be plastic, exterior cabinet to be 20 gauge type 304 stainless steel with merchandiser/woodgrain/stainless steel front, ice dispensing to result from a paddle wheel which lifts and agitates the ice, ice is controllable dispensed into cups from 8 oz. to 2 liters, eight foot three wire cord and plug, 120 Volt, 60 cycle, single phase, overall dimensions: 30" W x 31-3/4" D x 33-3/4" H, UL listed and NSF certified. Booth model ID or approved equal. Pg. 55 -

HISD FOOD SERVICES. Kitchen Equipment Specifications TN-BOOK

HISD FOOD SERVICES. Kitchen Equipment Specifications TN-BOOK HISD FOOD SERVICES Kitchen Equipment Specifications TN-BOOK April 2013 1 TABLE OF CONTENTS GENERAL CONDITIONS... 7 III. SCOPE OF WORK AND SPECIFIC CONDITIONS... 7 3.1 SCOPE OF WORK:... 7 3.2 SPECIFIC CONDITIONS:

More information

NOR-LAKE, INCORPORATED 727 Second Street Hudson, Wisconsin 54016

NOR-LAKE, INCORPORATED 727 Second Street Hudson, Wisconsin 54016 NOR-LAKE, INCORPORATED 727 Second Street Hudson, Wisconsin 54016 800-955-5253 715-386-2323 866-961-5253 Parts 800-388-5253 Service 715-386-6149 FAX www.norlake.com Kold Locker Walk-ins Standard Model Coolers

More information

INSULATED COLD STORAGE ROOMS (FOAMED IN-PLACE INSULATED PANELS)

INSULATED COLD STORAGE ROOMS (FOAMED IN-PLACE INSULATED PANELS) SECTION 11400 INSULATED COLD STORAGE ROOMS (FOAMED IN-PLACE INSULATED PANELS) PART 1 GENERAL 1.01 SUMMARY A. Section Includes: Pre-fabricated, free standing walk-in cooler/freezer rooms, metal clad, designed

More information

Canning Shed/Facility Equipment Specifications

Canning Shed/Facility Equipment Specifications Canning Shed/Facility Equipment Specifications Item Qty Description 1 1 ea WALK IN COOLER Fast Trak Indoor One Compartment Walk In, 8' x 8' x 7' 7" H, compartments, cooler with smooth aluminum interior

More information

BIDDING REQUIREMENTS/INFORMATION FOR EQUIPMENT FOR OWOSSO PUBLIC SCHOOLS

BIDDING REQUIREMENTS/INFORMATION FOR EQUIPMENT FOR OWOSSO PUBLIC SCHOOLS BIDDING REQUIREMENTS/INFORMATION FOR EQUIPMENT FOR OWOSSO PUBLIC SCHOOLS Owosso Public Schools desires to purchase equipment. Bidders are asked to bid on the complete package Sealed bids must be received

More information

Standard Model Coolers, Freezers and Combination Cooler/Freezers In Stock for SAME DAY SHIPMENT

Standard Model Coolers, Freezers and Combination Cooler/Freezers In Stock for SAME DAY SHIPMENT NOR-LAKE, INCORPORATED 727 Second Street P.O. Box 248 Hudson, Wisconsin 54016 800-955-5253 715-386-2323 866-961-5253 Parts 800-388-5253 Service 715-386-4290 FAX www.norlake.com Kold Locker Walk-Ins Standard

More information

INSULATED COLD STORAGE ROOMS (FOAMED IN-PLACE INSULATED PANELS)

INSULATED COLD STORAGE ROOMS (FOAMED IN-PLACE INSULATED PANELS) SECTION 11400 INSULATED COLD STORAGE ROOMS (FOAMED IN-PLACE INSULATED PANELS) PART 1 GENERAL 1.01 SUMMARY A. Section Includes: Pre-fabricated, free standing walk-in cooler/freezer rooms, metal clad, designed

More information

Kold Locker Walk in Standard walk in stocked for IMMEDIATE SHIPMENT

Kold Locker Walk in Standard walk in stocked for IMMEDIATE SHIPMENT 7750 Georgetown Rd. Indianapolis, IN 46268 800 215 9293 www.centralrestaurant.com Kold Locker Walk in Standard walk in stocked for IMMEDIATE SHIPMENT Stock No. 185 029 Walk in is located indoors, 4" thick

More information

Q SERIES MEDIUM TEMPERATURE REFRIGERATORS

Q SERIES MEDIUM TEMPERATURE REFRIGERATORS Item # Quantity C.S.I. Section 11400 FOOD EQUIPMENT Q SERIES MEDIUM STANDARD FEATURES Choice of finishes: Stainless steel exterior and interior; Stainless steel exterior, DuraFinish aluminum interior Galvanized

More information

INSTALLATION and OPERATION INSTRUCTIONS

INSTALLATION and OPERATION INSTRUCTIONS INSTALLATION and OPERATION INSTRUCTIONS Utility Coolers MODEL NOS. US4KP US10KP IMPORTANT INFORMATION This manual has been prepared to assist you in the installation of your Utility Cooler and to acquaint

More information

MINI-ROOM COOLERS, FREEZERS & COMBINATIONS

MINI-ROOM COOLERS, FREEZERS & COMBINATIONS NOR-LAKE SCIENTIFIC 727 Second Street Hudson, Wisconsin 54016 800-477-5253 7-386-2323 866-961-5253 Parts 800-388-5253 Service 7-386-4290 FAX www.norlakescientific.com SCIENTIFIC Mini-Room Walk-In Controlled

More information

HOLDING/PROOFING CABINETS HP2H-2M-SN APPLICATION OPTIONAL MODULAR CONSTRUCTION

HOLDING/PROOFING CABINETS HP2H-2M-SN APPLICATION OPTIONAL MODULAR CONSTRUCTION HP1H-M-SN HP1V-M-SN HPH-M-SN HPV-M-SN HOLDING/PROOFING CABINETS APPLICATION To satisfy a need for high quality, shipboard grade, heated products, Cospolich has introduced their "HP" class of horizontal

More information

Wall mount refrigeration systems available. PRS-2 SERIES Packaged Refrigeration Systems & Walk-in Combinations

Wall mount refrigeration systems available. PRS-2 SERIES Packaged Refrigeration Systems & Walk-in Combinations Wall mount refrigeration systems available PRS-2 SERIES Packaged Refrigeration Systems & Walk-in Combinations PRS-2: The Keyword Is Simple Simple Convenience The PRS-2 series combines durable walk-in panels

More information

Wall mount refrigeration systems available. PRS-2 SERIES Packaged Refrigeration Systems & Walk-in Combinations. KaTom Restaurant Supply, Inc.

Wall mount refrigeration systems available. PRS-2 SERIES Packaged Refrigeration Systems & Walk-in Combinations. KaTom Restaurant Supply, Inc. Wall mount refrigeration systems available PRS-2 SERIES Packaged Refrigeration Systems & Walk-in Combinations PRS-2: The Keyword Is Simple Simple Convenience The PRS-2 series combines durable walk-in panels

More information

FOGEL Caribbean Corporation

FOGEL Caribbean Corporation Sandwich Prep Tables Product Specification Sheets Construction Standard Features Stainless steel top, front, and sides Aluminum interior lining prevents corrosion Strong body with thick walls, injected

More information

Preparation Table Raised Condiment Rail models 8000N

Preparation Table Raised Condiment Rail models 8000N Preparation Table Raised Condiment Rail models 8000N model 8148N 8260N 8268N 8383N 835N 84111N Description: Available in six convenient sizes, 48 one door, 60 & 68 two door, 83 and 5 three door, and 111

More information

Installation & Operation Manual

Installation & Operation Manual Installation & Operation Manual Glass Frosters FR Series FR48 SS shown C US Form No. Z2296 Rev. 01.16.2015 Glass Frosters Installation & Operation Manual JOB AREA ITEM NO. MODEL NO. FR24 SERIES FR36 SERIES

More information

Installation & Operation Manual

Installation & Operation Manual Installation & Operation Manual Flat Top Bottle Cooler BC Series BC72 shown C US Form No. Z2295 Rev. 04.05.2018 JOB AREA ITEM NO. MODEL NO. BC24 SERIES BC36 SERIES BC48 SERIES BC24 shown BC72 shown BC48LT

More information

Undercounter Units. 20 Call or Text for pricing on True and other great brands! UNDERCOUNTERS & WORKTOPS (19 24) REFRIGERATION

Undercounter Units. 20 Call or Text for pricing on True and other great brands! UNDERCOUNTERS & WORKTOPS (19 24) REFRIGERATION UNDERCOUNTERS & WORKTOPS (19 24) REFRIGERATION July-December 2018 u ENERGY STAR Qualified All features apply to all units, except as noted. Aluminum with stainless steel floor interior and back Refrigerators

More information

roof finish is 26 gauge acrylic coated stucco galvanized steel.080 textured aluminum interior floor finish, where required

roof finish is 26 gauge acrylic coated stucco galvanized steel.080 textured aluminum interior floor finish, where required ITEM NO. PROJECT LOCATION DATE QTY. Quick Ship Walk-In Coolers & Freezers With Matching Refrigeration Systems FREE FREIGHT to domestic U.S. locations and select locations in Canada (consult your Master-Bilt

More information

10-Bilt. Walk-In Coolers & Freezers With Matching Refrigeration Systems FEATURES OPTIONS

10-Bilt. Walk-In Coolers & Freezers With Matching Refrigeration Systems FEATURES OPTIONS ITEM NO. PROJECT LOCATION DATE QTY. 10-Bilt Walk-In Coolers & Freezers With Matching Refrigeration Systems FEATURES OPTIONS CONSTRUCTION Models ship within 10 working days after order is received 4" thick

More information

DES MOINES PUBLIC SCHOOLS MADISON WALK-IN COOLER/FREEZER PROJECT. 806 E. Hoffman Street Des Moines, IA ADDENDUM NO.

DES MOINES PUBLIC SCHOOLS MADISON WALK-IN COOLER/FREEZER PROJECT. 806 E. Hoffman Street Des Moines, IA ADDENDUM NO. DES MOINES PUBLIC SCHOOLS MADISON WALK-IN COOLER/FREEZER PROJECT 806 E. Hoffman Street Des Moines, IA 50316 ADDENDUM NO. 1 April 3, 2017 Item 1: Item 2: Item 3: Item 4: See attached sketch showing the

More information

INSTALLATION and OPERATION INSTRUCTIONS

INSTALLATION and OPERATION INSTRUCTIONS INSTALLATION and OPERATION INSTRUCTIONS Glass Frosters MODEL NOS. FR24 Series FR36 Series FR48 Series FR60 Series c IMPORTANT INFORMATION This manual has been prepared to assist you in the installation

More information

Food Service. Top design, quality and availability both freezer and refrigerator models and offers innovative new advances long anticipated in the

Food Service. Top design, quality and availability both freezer and refrigerator models and offers innovative new advances long anticipated in the Food Service Food Service Metalfrio introduced its new line of stainless steel foodservice equipment in 011. This line includes both freezer and refrigerator models and offers innovative new advances long

More information

The following is a University standard specification and shall be reviewed and edited by the Design Professional to be project specific.

The following is a University standard specification and shall be reviewed and edited by the Design Professional to be project specific. DIVISION 13 21 00 CONTROLLED ENVIRONMENT ROOMS The following is a University standard specification and shall be reviewed and edited by the Design Professional to be project specific. GENERAL REQUIREMENTS

More information

Mobile Heated Cabinet

Mobile Heated Cabinet Job: Item No. Mobile Heated Cabinet Heavy duty heated holding/transport cabinet for use with 12 X 20 pans. All stainless steel construction Fully insulated Cabinets fully framed all vertical and horizontal

More information

Walk-Ins & Refrigeration Systems

Walk-Ins & Refrigeration Systems Walk-Ins & Refrigeration Systems Quality Engineered Refrigeration Since 1947 Kold Locker Fast-Trak Fineline 2 Walk-Ins Kold Locker Over 10,000 Kold Locker walk-in configurations are in stock and ready

More information

3 Year Parts/Labor Warranty Additional 2 Year Compressor Warranty

3 Year Parts/Labor Warranty Additional 2 Year Compressor Warranty Beverage Air ST34N S Item#: 2 Item No. Quantity 3779 Champion Blvd., Winston-Salem, NC 27105 1-888-845-9800 Fax# 1-336-245-6453 http://www.beverage-air.com Commercial Refrigeration Equipment General Specification

More information

Food Service Establishment Plan Review Form

Food Service Establishment Plan Review Form CITY OF PARK RIDGE 505 BUTLER PLACE PARK RIDGE, IL 60068 TEL: 847/ 318-5291 FAX: 847/ 318-6411 TDD:847/ 318-5252 URL:http://www.parkridge.us Food Service Establishment Plan Review Form THE FOLLOWING INFORMATION

More information

C. ASME Compliance: Fabricate and label water chiller heat exchangers to comply with ASME Boiler and Pressure Vessel Code: Section VIII, Division 1.

C. ASME Compliance: Fabricate and label water chiller heat exchangers to comply with ASME Boiler and Pressure Vessel Code: Section VIII, Division 1. SECTION 236426 - ROTARY-SCREW WATER CHILLERS PART 1 - GENERAL 1.1 SUMMARY A. This Section includes packaged, water cooled or air cooled as scheduled, electric-motor-driven, rotary-screw water chillers

More information

RedHots Chef s Line. Countertop Equipment

RedHots Chef s Line. Countertop Equipment RedHots Chef s Line Countertop Equipment RedHots Chef s Line A full range of models including fryers, charbroilers, griddles and hot plates, the Chef's Line series is especially engineered for foodservice

More information

SERVING LINE EQUIPMENT AND UNITS

SERVING LINE EQUIPMENT AND UNITS SECTION 11416 SERVING LINE EQUIPMENT AND UNITS PART 1 GENERAL 1.01 SUMMARY A. Related Sections: 1. 11401 - Custom Fabricated Equipment. 2. 11419 - Utility Distribution Systems. 3. Division 15 - Water supply,

More information

Line #: 1a, 1b, 1c (CCSD # 2) PASS-THRU HEATED CABINET (NARROW): VICTORY HS-1D-1-PT, ONLY

Line #: 1a, 1b, 1c (CCSD # 2) PASS-THRU HEATED CABINET (NARROW): VICTORY HS-1D-1-PT, ONLY Line #: 1a, 1b, 1c (CCSD # 2) PASS-THRU HEATED CABINET (NARROW): VICTORY HS-1D-1-PT, ONLY A. Provide one-section pass-thru heated cabinet. Net storage capacity to be minimum 23.7 cubic feet. Provide with

More information

SECTION PACKAGED ROOFTOP AIR CONDITIONING UNITS - CUSTOM

SECTION PACKAGED ROOFTOP AIR CONDITIONING UNITS - CUSTOM SECTION 23 81 06 - PACKAGED ROOFTOP AIR CONDITIONING UNITS - CUSTOM PART 1 - GENERAL 1.1 SUMMARY A. This Section includes equipment types that contain all the components of the refrigeration process within

More information

WCPT-3 and WCPT-4. Effective Date: 2017 IMPORTANT INFORMATION READ BEFORE USE. Drop-in Display Cases

WCPT-3 and WCPT-4. Effective Date: 2017 IMPORTANT INFORMATION READ BEFORE USE. Drop-in Display Cases WCPT-3 and WCPT-4 Service and Installation Manual Please read this manual completely before attempting to install or operate this equipment! Notify carrier of damage! Inspect all components immediately.

More information

4 04 Printed In U.S.A. (kdj) 1. Part No REFRIGERATOR

4 04 Printed In U.S.A. (kdj) 1. Part No REFRIGERATOR CABINET PARTS REFRIGERATOR 4 04 Printed In U.S.A. (kdj) 1 Part No. CABINET PARTS LITERATURE PARTS 1 2305802 Use & Care Guide 2301270 Service & Wiring Sheet 2305630 Energy Label 2220407 Modular Icemaker

More information

CABINET PARTS REFRIGERATOR. For Model: KSRS25FGSS11 (Stainless Steel) 6 00 Printed In U.S.A. (mdg) Part No Rev.B

CABINET PARTS REFRIGERATOR. For Model: KSRS25FGSS11 (Stainless Steel) 6 00 Printed In U.S.A. (mdg) Part No Rev.B CABINET PARTS REFRIGERATOR 6 00 Printed In U.S.A. (mdg) 1 Part No. Rev.B CABINET PARTS LITERATURE PARTS 1 LIT2206106 Use & Care Guide LIT2200278 Service & Wiring Sheet LIT2211866 Energy Guide LIT628370

More information

INSTALLATION and OPERATION INSTRUCTIONS

INSTALLATION and OPERATION INSTRUCTIONS INSTALLATION and OPERATION INSTRUCTIONS SINGLE DOOR freezer MODEL NOS. FN FS Finished Stainless Steel Top Non-Finished Top FS FN IMPORTANT INFORMATION This manual has been prepared to assist you in the

More information

"N-Width" Reach-In Refrigerator-Freezer Models/Self-Contained. Project Quantity Item # Model Specified: CSI Section 11400

N-Width Reach-In Refrigerator-Freezer Models/Self-Contained. Project Quantity Item # Model Specified: CSI Section 11400 Project Quantity Item # Model Specified: CSI Section 11400 "N-Width" Reach-In Refrigerator-Freezer Models/Self-Contained R SERIES Stainless Exterior & Interior Two & Three Section Models, 32" Deep 2-Section

More information

WHIRLPOOL REFRIGERADOR KSRS25FGSS13

WHIRLPOOL REFRIGERADOR KSRS25FGSS13 CABINET, LITERATURE 1 CABINET, LITERATURE 1 LIT2206106 Literature Parts (Use & Care Guide) 2 2174748 Front Roller (2) 3 3400517 Screw 4 2196236 Roller (Rear) (2) 5 489427 Screw 6 2155013 Clip, Grille 7

More information

CABINET PARTS For Models: KSRP25QDWH01, KSRP25QDAL01, KSRP25QDBL01 (White) (Almond) (Black)

CABINET PARTS For Models: KSRP25QDWH01, KSRP25QDAL01, KSRP25QDBL01 (White) (Almond) (Black) CABINET PARTS REFRIGERATOR 3 97 Printed In U.S.A. (RCG) 1 Part No. CABINET PARTS 1 Cabinet (Not A Serviceable Part) 2 2174748 Front Roller (2) 3 489456 Screw 4 981122 Roller (Rear) (2) 5 489427 Screw 6

More information

Mobile Foodservice Solutions. versatility, durability, efficiency

Mobile Foodservice Solutions. versatility, durability, efficiency Mobile Foodservice Solutions versatility, durability, efficiency Over 65 Years of Industry-Leading Cart Design and Manufacturing This is where it all began for us. It was 1945 when Caddy first started

More information

Freezers. Laboratory & Plasma. i.series Horizon Series. Distinctly. Innovation can be beautiful.

Freezers. Laboratory & Plasma. i.series Horizon Series. Distinctly. Innovation can be beautiful. Innovation can be beautiful. Freezers Laboratory & Plasma Distinctly Freezers Laboratory & Plasma Precisely executed. Sharply designed. Helmer has provided high-quality laboratory equipment and refrigerated

More information

Laboratory & Pharmacy Refrigerators

Laboratory & Pharmacy Refrigerators Innovation can be beautiful. Laboratory & Pharmacy Refrigerators Distinctly Laboratory & Pharmacy Refrigerators Precisely executed. Sharply designed. Helmer has provided high-quality laboratory equipment

More information

INSTALLATION and OPERATION INSTRUCTIONS

INSTALLATION and OPERATION INSTRUCTIONS INSTALLATION and OPERATION INSTRUCTIONS Single Door cooler series MODEL NOS. CS32SB CS32SG CS32SS CS32ST IMPORTANT INFORMATION To register your product, visit our web site at (www.perlick.com). Click on

More information

Industrial Freezer Sales A division of IDS 5311 Derry Avenue Building D Agoura Hills CA Phone (818) Fax (818)

Industrial Freezer Sales A division of IDS 5311 Derry Avenue Building D Agoura Hills CA Phone (818) Fax (818) UCUF191S-86, UCUF241S-86 and UCUF281S-86 UPRIGHT ULTRACOLD FREEZERS Control and Alarm Features Manual defrost, adjustable control range from -50 C to -86 C. UL/CUL Listed. Factory preset at -80 C. Advanced

More information

2018 PRICE LIST EffecTiVe 10/01/2018

2018 PRICE LIST EffecTiVe 10/01/2018 2018 PRICE LIST EffecTiVe 10/01/2018 831 E CAYUGA ST, PHILADELPHIA, PA 19124 USA (215) 464-6800 1-800-344-8222 FAX (215) 969-4890 E-MAIL: SALES@FOGELUSA.COM WWW.FOGELUSA.COM COUNTER TOP HINGED TABLE OF

More information

CABINET PARTS REFRIGERATOR

CABINET PARTS REFRIGERATOR CABINET PARTS REFRIGERATOR 1 94 Litho In U.S.A. 1 Part No. CABINET PARTS 2 2152011 Front Roller (2) 3 489393 Screw, 4 981122 Roller (Rear) (2) 5 488454 Screw 6 2155013 Clip, Grille 7 489242 Screw 9 836196

More information

Number of sides for work space where food preparation occurs. Minimum width between food equipment and walls in work space.

Number of sides for work space where food preparation occurs. Minimum width between food equipment and walls in work space. This guide will assist you with providing information required by the Anne Arundel County Department of Health to determine compliance with COMAR 10.15.03 Food Service Facilities. The applicant or owner

More information

Long Island School Nutrition Director's Association

Long Island School Nutrition Director's Association Page No 1 88094 Cabinet, Heated, Model 1826-15BC EACH 17 1 Whitco Model 1826-15BC-1S; 66 in high, 27 in wide, 33.75in deep; 120 volts; 1200 watts; 10 amps; 5 in casters; 15 sheet pan capacity; 20 guage

More information

Front Roller (2) Screw Roller (Rear) (2) Screw Clip, Grille Screw Insert, Air

Front Roller (2) Screw Roller (Rear) (2) Screw Clip, Grille Screw Insert, Air 2 2174748 Front Roller (2) 3 489456 Screw 4 981122 Roller (Rear) (2) 5 489427 Screw 6 2155013 Clip, Grille 7 489242 Screw 8 2176796 Insert, Air Baffle 9 2156056 Shim 10 2158579 Enclosure, Terminal Block

More information

Freezers. Upright Laboratory & Plasma. i.series Horizon Series

Freezers. Upright Laboratory & Plasma. i.series Horizon Series Freezers Upright Laboratory & Plasma i.series Laboratory & Plasma Freezers Helmer has provided high-quality laboratory equipment and refrigerated products for over 35 years. Our experience and attention

More information

APPENDIX 3J FOOD SERVICES SPECIFICATIONS

APPENDIX 3J FOOD SERVICES SPECIFICATIONS APPENDIX 3J FOOD SERVICES SPECIFICATIONS 1. FOOD SERVICES 1.1 Design Consultant Project Co will retain as part of its professional design team a qualified food service consultant that is a professional

More information

Refrigerators. Upright Blood Bank. i.series Horizon Series

Refrigerators. Upright Blood Bank. i.series Horizon Series Refrigerators Upright Blood Bank Blood Bank Refrigerators Helmer has provided high-quality laboratory equipment and refrigerated products for over 30 years. Our experience and attention to detail allow

More information

Glass Doors, Hinged Bottom Mounts

Glass Doors, Hinged Bottom Mounts Product Specification Sheets Construction Standard Features Interior and exterior constructed of heavyduty white coated steel CFC free foamed-in-place polyurethane insulation Stainless steel floor Externally

More information

Freezers. Laboratory & Plasma. i.series Horizon Series

Freezers. Laboratory & Plasma. i.series Horizon Series Freezers Laboratory & Plasma Laboratory & Plasma Freezers Precisely executed. Sharply designed. Helmer has provided high-quality laboratory equipment and refrigerated products for over 30 years. Our experience

More information

DIVISION 10 SPECIALTIES

DIVISION 10 SPECIALTIES DIVISION 10 SPECIALTIES 11/11 SECTION 10 21 13.16 PLASTIC LAMINATE TOILET COMPARTMENTS PART 1 - GENERAL 1.01 SECTION INCLUDES Plastic laminate toilet compartments, urinal screens, head rail braced. 1.02

More information

Heating & Holding Cabinets

Heating & Holding Cabinets K Heating & Holding Cabinets In This Section Heated Cabinet/Proofer K-1...254 Universal Heated Proofer K-2...256 Holding Cabinets Stainless Steel K-3...258 Humidified Holding Cabinets K-4...260 Heated

More information

The Endura Series. The right combination of versatility, efficiency and reliability in foodservice equipment.

The Endura Series. The right combination of versatility, efficiency and reliability in foodservice equipment. The Endura Series The right combination of versatility, efficiency and reliability in foodservice equipment. With reach-ins, pass-thrus, roll-thrus, prep tables and heated cabinets, Endura is one of the

More information

A. Air Handling Units shall be designed to the specific requirements of the application: Recirculation or 100% Makeup.

A. Air Handling Units shall be designed to the specific requirements of the application: Recirculation or 100% Makeup. SECTION 23 70 00- CENTRAL HVAC EQUIPMENT PART 1: GENERAL 1.1 PURPOSE: A. This standard is intended to provide useful information to the Professional Service Provider (PSP) to establish a basis of design.

More information

CABINET PARTS. For Models: KSRT25CRWH00, KSRT25CRBT00, KSRT25CRBL00, KSRT25CRSS00 (White) (Biscuit) (Black) (Stainless Steel)

CABINET PARTS. For Models: KSRT25CRWH00, KSRT25CRBT00, KSRT25CRBL00, KSRT25CRSS00 (White) (Biscuit) (Black) (Stainless Steel) CABINET PARTS REFRIGERATOR 11 05 Printed In U.S.A. (kdr) 1 Part No. Rev. A CABINET PARTS 1 Literature Parts 2315197 Energy Guide 2308392 Owner s Manual 2303925 Service Sheet 2303929 Wiring Sheet 2220407

More information

SECTION WATER-SOURCE UNITARY HEAT PUMPS

SECTION WATER-SOURCE UNITARY HEAT PUMPS SECTION 23 81 46 WATER-SOURCE UNITARY HEAT PUMPS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of Contract, including General and Supplementary Conditions and Division 1 Specification

More information

UNIFIED FACILITIES GUIDE SPECIFICATIONS

UNIFIED FACILITIES GUIDE SPECIFICATIONS USACE / NAVFAC / AFCEC / NASA UFGS-11 31 13 (August 2017) --------------------------- Preparing Activity: NAVFAC Superseding UFGS-11 31 13 (August 2008) UNIFIED FACILITIES GUIDE SPECIFICATIONS References

More information

KSRG25FKWH18, KSRG25FKBL18, KSRG25FKBT18

KSRG25FKWH18, KSRG25FKBL18, KSRG25FKBT18 CABINET PARTS REFRIGERATOR 06 06 Printed In U.S.A. (kdr) 1 Part No. CABINET PARTS 1 Literature Parts 2318581 Use & Care Guide 2255385 Service & Wiring Sheet 2318618 Energy Guide 2220407 Modular Icemaker

More information

Submittal Data Performance Data Electrical Data

Submittal Data Performance Data Electrical Data ERMS Series Submittal Data Submittal Data Unit Designation: Job name: Architect: Engineer: Contractor: Performance Data Revision: 07/01/11 Cooling Capacity: EER: Heating Capacity: COP: Ambient Air Temp:

More information

New Food Service Plan Review Checklist

New Food Service Plan Review Checklist New Food Service Plan Review Checklist The following items should be completed before you return your application. Read Starting a Food Service Brochure to help you in the process. Confirm whether property

More information

Cabinet & Merchandiser Price List

Cabinet & Merchandiser Price List Cabinet & Merchandiser Price List Effective January 1, 2018 2018 Master-Bilt Products, an unincorporated division of Standex International Corporation. All rights reserved. Contents Section Page Ice Cream

More information

TB SERIES. Glycol Pizza/Salad/Sandwich Prep Tables Self-Contained. Project Quantity Item # Model Specified: CSI Section 11400

TB SERIES. Glycol Pizza/Salad/Sandwich Prep Tables Self-Contained. Project Quantity Item # Model Specified: CSI Section 11400 Glycol Pizza/Salad/Sandwich Prep Tables Self-Contained TB SERIES 46", 60", 65", 71", 91" & 113" Wide Models Glycol 2 Row Pan Rail Models 46" Long Model for 12 x 1/6 Pans TB046SL2S 60" Long Model for 16

More information

CABINET PARTS For Model: ED5GTGXNQ14, ED5GTGXNB14 (White) (Black)

CABINET PARTS For Model: ED5GTGXNQ14, ED5GTGXNB14 (White) (Black) CABINET PARTS REFRIGERATOR 07 07 Litho In U.S.A. (mat) 1 Part No. Rev. A CABINET PARTS 1 Literature Parts 2315254 Use & Care Guide 2255373 Service & Wiring Sheet 2318639 Energy Guide 628370 Modular Icemaker

More information

Specifications 7/25/2012

Specifications 7/25/2012 Item 1 - MERCHANDISER, OPEN (1 REQ'D) Project Aspen Art Museum-Cafe From Jeff Katz (303) 440-4142 RPI Industries Model SCRFC3648R Bravo Air Screen Display Case, 36" L x 48" H, self-contained refrig., front

More information

CABINET PARTS For Models: KSRG22FKWH17, KSRG22FKBT17, KSRG22FKBL17 (White) (Biscuit) (Black)

CABINET PARTS For Models: KSRG22FKWH17, KSRG22FKBT17, KSRG22FKBL17 (White) (Biscuit) (Black) CABINET PARTS REFRIGERATOR 5 06 Litho In U.S.A. (kdr) 1 Part No. CABINET PARTS 1 LITERATURE PARTS 2315214 Use & Care Guide 2255385 Service & Wiring Sheet 2315352 Energy Label 2220407 Modular Icemaker Service

More information

B. Unit construction shall comply with ASHRAE 15 Safety Code, NEC, and ASME applicable codes (U.S.A. codes).

B. Unit construction shall comply with ASHRAE 15 Safety Code, NEC, and ASME applicable codes (U.S.A. codes). Guide Specifications PART 1 GENERAL 1.01 SYSTEM DESCRIPTION Microprocessor controlled, air-cooled liquid chiller utilizing scroll compressors, low sound fans, hydronic pump system and optional fluid storage

More information

Concepts Serving Systems

Concepts Serving Systems Concepts Serving Systems Installation Manual Please read this manual completely before attempting to install or operate this equipment! Notify carrier of damage! Inspect all components immediately. February

More information

Shelleybasic. Shelleybasic. by Delfield

Shelleybasic. Shelleybasic. by Delfield Shelleybasic by Delfield Shelleybasic by Delfield The Delfield Company 980 S. Isabella Rd. Mt. Pleasant, MI 48858 Phone: 800.733.8948 or 800.733.8821 Fax: 800.669.0619 Web: www.delfield.com DBSHELLEYBASIC

More information

Front Roller (2) Screw Roller (Rear) (2) Screw Clip, Grille Screw Shim

Front Roller (2) Screw Roller (Rear) (2) Screw Clip, Grille Screw Shim 2 2174748 Front Roller (2) 3 489456 Screw 4 981122 Roller (Rear) (2) 5 489427 Screw 6 2155013 Clip, Grille 7 489478 Screw 9 2156056 Shim 12 2196046 Hinge Top (2) 13 2196048 Shim, Hinge Top 14 489284 Screw

More information

CABINET PARTS. REFRIGERATOR For Models: KSRB22FHWH01, KSRB22FHBL01, KSRB22FHSS01, KSRB22FHBT01 (White) (Black) (Stainless Steel) (Biscuit)

CABINET PARTS. REFRIGERATOR For Models: KSRB22FHWH01, KSRB22FHBL01, KSRB22FHSS01, KSRB22FHBT01 (White) (Black) (Stainless Steel) (Biscuit) CABINET PARTS REFRIGERATOR 3 00 Litho In U.S.A. (dmz) 1 Part No. Rev. A 1 LITERATURE PARTS LIT2200139 Use & Care Guide LIT2200278 Service & Wiring Sheet LIT628370 Modular Icemaker Service Sheet LIT2204298

More information

WHIRLPOOL REFRIGERADOR GS2SHGXLQ01

WHIRLPOOL REFRIGERADOR GS2SHGXLQ01 CABINET, LITERATURE 1 CABINET, LITERATURE 1 LIT2220425 LITERATURE PARTS (Energy Label) 1 LIT2220699 LITERATURE PARTS (Owner`s Manual) 1 LIT2255381 LITERATURE PARTS (Service & Wiring Sheet) 1 LIT628370

More information

F o o d S e r v i c e

F o o d S e r v i c e Food Service Wall-Hung Hand Sinks Glastender s all stainless steel wall-hung hand sinks are manufactured with total welded construction to meet all NSF standards. Optional heavy-duty faucets are NSF/ANSI

More information

CABINET PARTS For Models: GS6SHAXKQ01, GS6SHAXKT01, GS6SHAXKB01, GS6SHAXKS01 (White) (Biscuit) (Black) (Stainless Steel)

CABINET PARTS For Models: GS6SHAXKQ01, GS6SHAXKT01, GS6SHAXKB01, GS6SHAXKS01 (White) (Biscuit) (Black) (Stainless Steel) CABINET PARTS REFRIGERATOR 3 01 Printed In U.S.A. (mdg) 1 Part No. CABINET PARTS LITERATURE PARTS 1 LIT2216812 Energy Guide LIT2205958 Owner s Manual LIT2216656 Service & Wiring Sheet LIT628370 Modular

More information

CABINET PARTS REFRIGERATOR. For Models: ED5VHGXMQ00, ED5VHGXMT00, ED5VHGXMB00 (White) (Biscuit) (Black) 8 03 Litho In U.S.A. (kdj)

CABINET PARTS REFRIGERATOR. For Models: ED5VHGXMQ00, ED5VHGXMT00, ED5VHGXMB00 (White) (Biscuit) (Black) 8 03 Litho In U.S.A. (kdj) CABINET PARTS REFRIGERATOR 8 03 Litho In U.S.A. (kdj) 1 Part No. Rev. C CABINET PARTS 1 LIT2220692 Use & Care Guide LIT2255377 Service & Wiring Sheet LIT2260931 Energy Label LIT628370 Modular Icemaker

More information

Walk-in Refrigerated Rooms. An Overview of Requirements, Options and Construction Details

Walk-in Refrigerated Rooms. An Overview of Requirements, Options and Construction Details Walk-in Refrigerated Rooms An Overview of Requirements, Options and Construction Details Definition A refrigerated room is a stand alone structure designed to hold products at either a medium temperature

More information

CABINET PARTS. For Models: GS5SHAXNQ02, GS5SHAXNT02, GS5SHAXNB02, GS5SHAXNS02, GS5SHAXNL02 (White) (Biscuit) (Black) (Stainless Steel) (Stainless VCM)

CABINET PARTS. For Models: GS5SHAXNQ02, GS5SHAXNT02, GS5SHAXNB02, GS5SHAXNS02, GS5SHAXNL02 (White) (Biscuit) (Black) (Stainless Steel) (Stainless VCM) CABINET PARTS REFRIGERATOR 10 05 Printed In U.S.A. (kdr) 1 Part No. CABINET PARTS 1 Literature Parts 2305895 Energy Guide 2315213 Owner s Manual 2255955 Service & Wiring Sheet 2220407 Modular Icemaker

More information

All food service facilities must be equipped with the following items for the pre-opening inspection:

All food service facilities must be equipped with the following items for the pre-opening inspection: DEPARTMENT OF HEALTH FOOD SERVICE FACILITY Pre-Opening Checklist This checklist is provided as a guide to prepare for the pre-opening inspection of a newly constructed, remodeled or a change-of-ownership

More information

Glass Door Merchandiser

Glass Door Merchandiser Glass Door Merchandiser Model Number: Issued: 02-22-2017 Revised: 02-22-2017 2 TABLE OF CONTENTS UNIT FEATURES 4 Page CROSS SECTION VIEWS 5 EXPLODED VIEW 6, 7 REFRIGERATION SYSTEM 8, 9 CONDENSING UNIT

More information

FOUNTAINS UGA DESIGN & CONSTRUCTION SUPPLEMENTAL GENERAL REQUIREMENTS & STANDARDS APRIL 30,

FOUNTAINS UGA DESIGN & CONSTRUCTION SUPPLEMENTAL GENERAL REQUIREMENTS & STANDARDS APRIL 30, 13 12 00 FOUNTAINS A. Due to water conservation efforts and the high maintenance requirements of fountains, new interior and / or exterior fountains are not allowed. B. If a variance is granted for a fountain,

More information

CABINET PARTS REFRIGERATOR. For Models: GD2SHAXKQ03, GD2SHAXKT03, GD2SHAXKB03 (White) (Biscuit) (Black) 5 02 Litho In U.S.A. (mek) 1. Part No.

CABINET PARTS REFRIGERATOR. For Models: GD2SHAXKQ03, GD2SHAXKT03, GD2SHAXKB03 (White) (Biscuit) (Black) 5 02 Litho In U.S.A. (mek) 1. Part No. CABINET PARTS REFRIGERATOR 5 02 Litho In U.S.A. (mek) 1 Part No. CABINET PARTS 1 LITERATURE PARTS LIT2220699 Use & Care Guide LIT2220104 Service & Wiring Sheet LIT2220300 Energy Guide LIT2220407 Modular

More information

Table of Contents. Specifications... page 2. Installation... page 3. Customizing... page 4. Reversing door swing... page 5

Table of Contents. Specifications... page 2. Installation... page 3. Customizing... page 4. Reversing door swing... page 5 Introduction The Scotsman Compact Refrigerator is a unique product, capable of being built into a cabinet because of its front vented, forced-air cooling system. It s also designed to be a companion to

More information

CABINET PARTS. For Models: ED5SHAXMQ00, ED5SHAMXT00, ED5SHAXMB00 (White) (Biscuit) (Black) REFRIGERATOR. Part No Rev.A

CABINET PARTS. For Models: ED5SHAXMQ00, ED5SHAMXT00, ED5SHAXMB00 (White) (Biscuit) (Black) REFRIGERATOR. Part No Rev.A CABINET PARTS REFRIGERATOR 4 04 Printed In U.S.A. (kdj) 1 Part No. Rev.A LITERATURE PARTS 1 LIT2261135 Energy Guide LIT2255705 Owner s Manual LIT2255380 Service & Wiring Sheet LIT2220407 Modular Icemaker

More information

UNIFIED FACILITIES GUIDE SPECIFICATIONS

UNIFIED FACILITIES GUIDE SPECIFICATIONS USACE / NAVFAC / AFCEC / NASA UFGS-11 31 13 (August 2008) --------------------------- Preparing Activity: NAVFAC Superseding UFGS-11 31 13 (April 2006) UNIFIED FACILITIES GUIDE SPECIFICATIONS References

More information

We maintain stock in many of our most popular models for immediate shipment.

We maintain stock in many of our most popular models for immediate shipment. Marine Refrigeration www.rtfmanufacturing.com Equipment Catalog Why Choose RTF Manufacturing? Superior Design RTF Manufacturing Provides State-of-the-Art, Quality-Designed Refrigeration Equipment for the

More information

Glass Door Merchandiser. Model RM-49

Glass Door Merchandiser. Model RM-49 Glass Door Merchandiser Model Number: Issued: 02-22-2017 Revised: 02-22-2017 2 TABLE OF CONTENTS UNIT FEATURES 4 Page CROSS SECTION VIEWS 5 EXPLODED VIEW 6, 7 REFRIGERATION SYSTEM 8, 9 CONDENSING UNIT

More information

Your best bet for everything under the cherry, in the frosted glass and above the cone since Product Catalog

Your best bet for everything under the cherry, in the frosted glass and above the cone since Product Catalog Your best bet for everything under the cherry, in the frosted glass and above the cone since 1929. Product Catalog Yesterday Founded in 1929, SaniServ began as a manufacturer of amusement park equipment

More information

CABINET PARTS For Models: KSBP25FKSS01 (Stainless Steel)

CABINET PARTS For Models: KSBP25FKSS01 (Stainless Steel) CABINET PARTS REFRIGERATOR 8 03 Litho In U.S.A. (kdj) 1 Part No. Rev. B LITERATURE PARTS 1 LIT2221516 Use & Care Guide LIT2214447 Service & Wiring Sheet LIT2220332 Energy Label LIT628370 Modular Icemaker

More information

CABINET PARTS For Models: ED5RHEXNL00 (Stainless VCM)

CABINET PARTS For Models: ED5RHEXNL00 (Stainless VCM) CABINET PARTS REFRIGERATOR 11 06 Litho In U.S.A. (kdj) 1 Part No. 1 LIT2188771 Use & Care Guide LIT2255373 Service & Wiring Sheet LIT2305928 Energy Label LIT628370 Modular Icemaker Service Sheet 2 2174748

More information

DEMO - Bevles - BEVLES PASS THRU - HCSS34W4. USED - Berkel - BERKEL SLICER $595

DEMO - Bevles - BEVLES PASS THRU - HCSS34W4. USED - Berkel - BERKEL SLICER $595 DEMO - Bevles - BEVLES PASS THRU - HCSS34W4 $895 BEVLES PASS THEU HOLDING CABINE, UNDERCOUNTER TYPE, 208 VOLT, 1 PHASE USED - Berkel - BERKEL SLICER - 909 $595 BERKEL SLICING MACHINE, 12'' BLADE, 115VOLT

More information

FRESNO COUNTY HUMAN SERVICES SYSTEM ENVIRONMENTAL HEALTH SYSTEM P.O. Box Fresno, CA Telephone (209)

FRESNO COUNTY HUMAN SERVICES SYSTEM ENVIRONMENTAL HEALTH SYSTEM P.O. Box Fresno, CA Telephone (209) FRESNO COUNTY HUMAN SERVICES SYSTEM ENVIRONMENTAL HEALTH SYSTEM P.O. Box 11867 Fresno, CA 93775 Telephone (209) 445-3392 CONSTRUCTION REQUIREMENTS FOR RETAIL FOOD ESTABLISHMENTS BEFORE CONSTRUCTING, ENLARGING,

More information

MACH N-407 Heat Pump Air-Cooled Chiller

MACH N-407 Heat Pump Air-Cooled Chiller MACH060-01-N-407 Heat Pump Air-Cooled Chiller Heat Pump Air-Cooled Chillers for Global Residential and Light Commercial Microclimates MACH NOMENCLATURE BREAKDOWN MACH-060-01 - N - 407 Refrigerant Type

More information

CABINET PARTS For Models: KSCS25FKSS00 (Stainless Steel)

CABINET PARTS For Models: KSCS25FKSS00 (Stainless Steel) CABINET PARTS REFRIGERATOR 8 03 Litho In U.S.A. (kdj) 1 Part No. Rev. C CABINET PARTS LITERATURE PARTS 1 LIT2254909 Use & Care Guide LIT2214447 Service & Wiring Sheet LIT2220332 Energy Label LIT628370

More information

CABINET PARTS For Models: 7GS2SHEXPQ03, 7GS2SHEXPL03 (White) (Stainless VCM) REFRIGERATOR

CABINET PARTS For Models: 7GS2SHEXPQ03, 7GS2SHEXPL03 (White) (Stainless VCM) REFRIGERATOR CABINET PARTS REFRIGERATOR 03 07 Litho In U.S.A. (mat) 1 Part No. Rev A CABINET PARTS 1 Literature Parts 2261383 Use & Care Guide 2255955 Service & Wiring Sheet 2261377 Energy Guide 2220407 Modular Icemaker

More information

CABINET PARTS For Models: GD22DFXFW01, GD22DFXFN01, GD22DFXFB01 (White) (Almond) (Black)

CABINET PARTS For Models: GD22DFXFW01, GD22DFXFN01, GD22DFXFB01 (White) (Almond) (Black) CABINET PARTS REFRIGERATOR 3-99 Litho In U.S.A. (dmz) Part No. 1 CABINET PARTS 1 LITERATURE PARTS LIT2186560 Use & Care Guide LIT2200277 Service & Wiring Sheet LIT2203988 Energy Label LIT628370 Modular

More information