SYSTEM BASIC WHIRLPOOLS

Transcription

1 SYSTEM BASIC WHIRLPOOLS CB 2000 Kohler Co.

2 IMPORTANT SAFETY INSTRUCTIONS ATTENTION INSTALLER: INSTRUCTIONS PERTAINING TO RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS READ AND FOLLOW ALL INSTRUCTIONS SAVE THESE INSTRUCTIONS WARNING: When using this unit, always follow basic precautions, including the following: WARNING: RISK OF ELECTRICAL SHOCK. The unit must be connected only to a circuit that is protected by a Ground-Fault Circuit-Interrupter (GFCI). Such a GFCI should be provided by the installer and should be tested on a routine basis. To test the GFCI, press the test button. The GFCI should interrupt power. Press the reset button. Power should be restored. If the GFCI fails to operate in this manner, there is a ground current flowing or the GFCI is defective. The possibility of an electric shock may exist. DO NOT use this unit. Disconnect the unit and have the problem corrected by a qualified licensed electrician. Grounding is required. The unit should be installed and grounded by a qualified service representative. A pressure wire connector is provided on the pump to permit connection of a solid copper bonding conductor between this unit and all other electrical equipment and exposed metal in the vicinity, as needed to comply with local requirements. DANGER: RISK OF INJURY. Hot whirlpool baths can put certain stresses on the body, as do any hot bath, shower, sauna, or steam bath. Prolonged immersions in hot water may induce hyperthermia. Hyperthermia occurs when the internal temperature of the body reaches a level several degrees above the normal body temperature of 98.6 F. The symptoms of hyperthermia include an increase in the internal body temperature, dizziness, lethargy, drowsiness, and fainting. The effects of hyperthermia include: (1) failure to perceive heat, (2) failure to recognize the need to exit the bath, (3) unawareness of impending hazard, (4) fetal damage in pregnant women, (5) physical inability to exit the bath, and (6) unconsciousness resulting in the danger of drowning. Warning: The use of alcohol, drugs, or other medication can greatly increase the risk of fatal hyperthermia. DO NOT operate this unit without the guard on the suction fitting. Never drop or insert any object into any opening. Use this unit only for its intended use as denoted in this manual. DO NOT use attachments not recommended by the Kohler Co. Install to permit access for servicing unless the whirlpool is installed with an optional, removable apron. DANGER: RISK OF INJURY. To reduce the risk of injury, do not permit children to use this unit unless they are closely supervised at all times. CAUTION: Risk of concealed leakage and product damage. Do not run this whirlpool without sufficient water in the bath. Running the pump dry may damage the pump and cause concealed water leakage. Never run the whirlpool without at least 2 to 3 of water covering the highest jet CB 2

3 TABLE OF CONTENTS IMPORTANT SAFETY INSTRUCTIONS INTRODUCTION PRODUCT NOTICES Installer Hazard Notification Factory-Assembled Features PRODUCT REQUIREMENTS Summary of Key Requirements Plumbing Specifications Product Inspection Connections and Service Access Electrical Requirements INSTALLATION REQUIREMENTS Tools Required Materials Required Clearance Requirements New Or Replacement Installation Requirements 5 SITE REQUIREMENTS Old Bath Removal Subfloor Preparation Stud Pocket Preparation Plumbing Preparation BEFORE INSTALLING UNIT Tiling-In Bead Installation Partially Install Bath Drain Protect Unit INSTALL THE WHIRLPOOL Set-In Install Plumbing ELECTRICAL CONNECTIONS Identify Electrical Requirements Wiring Information WATER TEST WHIRLPOOL & ELECTRONICS.. 10 COMPLETE FINISH WALL COMPLETE INSTALLATION Install Handles and Spout Remove Protective Film CLEAN-UP AFTER INSTALLATION CONFIRM PROPER OPERATION Start-Up Operating Sequence Troubleshoot System INTRODUCTION Please read these instructions carefully to familiarize yourself with the required tools, materials, and installation sequences. Follow the sections that pertain to your particular installation. This will help you avoid costly mistakes. In addition to proper installation, read all operating and safety instructions. All information in this manual is based upon the latest product information available at the time of publication. Kohler Co. reserves the right to make changes in product characteristics, packaging, or availability at any time without notice. The variety of installations possible with this bath may require framing procedures other than those described in this manual. Identify and record the model and serial numbers below (found at the pump end of the bath): Model No. Serial No. Date of Manufacture CB

4 1. PRODUCT NOTICES A. INSTALLER HAZARD NOTIFICATION DANGER: Risk of fire, electric shock, or injury to persons. Read important safety instructions on inside front cover of these instructions. WARNING: Risk of electrical shock. A licensed electrician should make all electrical connections. WARNING: Risk of electrical shock. Connect only to a circuit protected by a Ground-Fault Circuit-Interrupter (GFCI). WARNING: Risk of electrical shock. Disconnect power before servicing. WARNING: Risk of injury or property damage. Please read all instructions thoroughly before beginning installation, including the following Product Requirements. NOTICE: Follow all local plumbing and electrical codes. B. FACTORY-ASSEMBLED FEATURES Factory installed components include pump with air switch transmitter and air control. No installation is needed. The whirlpool pump and piping are factory-assembled. WARNING: Unauthorized modification may cause unsafe operation and poor performance of the whirlpool. Do not relocate the whirlpool pump, or make other modifications to the whirlpool system, as this could adversely affect the performance and safe operation of the whirlpool. Kohler Co. shall not be liable under its warranty or otherwise for personal injury or damage caused by any such unauthorized modification. 2. PRODUCT REQUIREMENTS A. SUMMARY OF KEY REQUIREMENTS Install unit to a level subfloor. Provide properly dimensioned framing. s are designed for a variety of installations, depending upon the model chosen. C. PRODUCT INSPECTION Carefully unpack the whirlpool, remove the protective tape, and inspect the unit for damage. Leave all materials in the carton during construction to prevent damage. Do not remove the clear protective film from the whirlpool surface until installation is complete. NOTICE: Make sure both union connections to the pump are securely tightened. B. PLUMBING SPECIFICATIONS Confirm adequate mounting and connection space of the faucet specified for your installation. D. CONNECTIONS AND SERVICE ACCESS Before installation, ensure proper access to the final connections. NOTICE: Provide unrestricted service access to the pump. An access panel must be constructed to allow for sufficient clearance for servicing the pump or controls. The access panel must be located at the pump end of the whirlpool. E. ELECTRICAL REQUIREMENTS The installation must have a Class A Ground-Fault Circuit-Interrupter (GFCI). The GFCI protects against line-to-ground shock hazard. Use a 120 V, 15 A, 60 Hz dedicated service for the whirlpool CB 4

5 3. INSTALLATION REQUIREMENTS A. TOOLS REQUIRED Conventional woodworking tools Arc pliers or 14 pipe wrench Rule Level Safety shoes Safety glasses Square Screwdriver Pliers Utility knife B. MATERIALS REQUIRED Plumbers putty Wall coverings, as necessary Silicone sealant Gypsum cement (optional) Construction adhesive (optional) 2x4 s Drop cloth Nails Lag screws C. CLEARANCE REQUIREMENTS Check the roughing-in and room dimensions to provide adequate available space for the bath unit. D. NEW OR REPLACEMENT INSTALLATION REQUIREMENTS This unit can be installed in new or existing bathrooms. For new installations: Position the plumbing according to the roughing-in document packed with the whirlpool. Cap the supplies, and check for leaks. For replacement installations: Remove the old bath. Remove the old wall material, and remove any old floor covering from the area. Remove any old plumbing that does not conform to roughing-in requirements. 4. SITE REQUIREMENTS A. OLD BATH REMOVAL Disconnect the drain at the trap. Remove the old wall material. Slip boards under the old bath feet to protect the floor and slide the old bath out of the recess as illustrated. Old Bath Floor Protection Boards B. SUBFLOOR PREPARATION Check the flooring under the bath, and make repairs as needed. Make sure the subfloor is level CB

6 C. STUD POCKET PREPARATION Construct a minimum 2x4 recess designed for your particular installation. Make sure you allow for access to the pump in the event the unit requires service. When constructing the framing, allow for the thickness of sub and finish wall materials. If an apron wall without a ledge is desired, the finished apron wall surface must be 1/16 under the bath rim. Possible stud frame arrangements are illustrated below. Use the stud construction appropriate for your particular whirlpool model. Some modifications may be needed for other types of construction, if preferred. 1. Corner Installation: The suggested stud construction is illustrated. Rim 1/16 Gap Between Rim and Framing 2. Recess Installation: The suggested stud construction is illustrated. Rim 1/16 Gap Between Rim and Framing 3. Peninsular Installation: The suggested stud construction is illustrated. Rim 1/16 Gap Between Rim and Framing CB 6

7 4. Sunken Installation (excluding oval models): The suggested stud construction is illustrated. Refer to the roughing-in document packed with the whirlpool. Do not hang the whirlpool by the rim. Rim 1/16 Gap Between Rim and Framing 5. Sunken Installation (oval models): Carefully position the whirlpool face down in the desired installation location. Draw a line around the entire edge. Measure in from the line 3/4, and draw a second line. This is your cut line. Cut out by following the cut line. Make sure the whirlpool will be supported by the whirlpool base, not the rim. Do not hang the whirlpool by the rim. Rim 1/16 Gap Between Rim and Framing D. PLUMBING PREPARATION Position the plumbing according to the roughing-in dimensions. Cap the supplies, and check for leaks. 5. BEFORE INSTALLING UNIT A. TILING-IN BEAD INSTALLATION A tiling-in bead is recommended for use along the side of the bath that contacts the wall. This bead prevents water from seeping between the bath and the wall. Install this bead now. Refer to the installation instructions packed with the tiling-in bead. B. PARTIALLY INSTALL BATH DRAIN Install the whirlpool drain according to the drain manufacturer s instructions. Do not connect the trap at this time. C. PROTECT WHIRLPOOL UNIT Position a drop cloth or similar material in the bottom of the unit. Be careful not to scratch the surface of the product CB

8 6. INSTALL THE WHIRLPOOL A. WHIRLPOOL SET-IN Rim Choose the installation option (Step 1., 2., or 3. below) that applies to your particular installation. Follow the appropriate instructions. 1/16 Gap Between Rim and Framing If the subfloor is not level, some shimming of the bath will be necessary. NOTICE: Do not hang the whirlpool by the rim. 1. Option For Sunken Installation: Set the bath into the sunken installation. Make sure the unit is level and resting on the whirlpool base. Use lag screws to secure the pump base to the floor. Pre-drill the holes as needed. Insert the drain tailpiece into the trap. Apply a bead of silicone sealant under the rim of the unit. CAUTION: Risk of product damage. Do not hang the unit by the rim. 2. Option For Using Gypsum: Spread a 2 thick layer of gypsum cement on the floor where the bath is to be set. This will help secure, level, and support the unit. Set the bath into position. Insert the drain tailpiece into the trap. Make sure the whirlpool is level and resting flat on the whirlpool base. Use lag screws to secure the pump base to the floor. Pre-drill the holes as needed. 3. Option For Using Construction Adhesive: Apply a generous amount of construction adhesive to the bottom of the base. Set the bath in the desired location, and level it. Insert the drain tailpiece into the trap. Make sure the whirlpool is level and resting flat on the whirlpool base. Use lag screws to secure the pump base to the floor. Pre-drill the holes as needed. Apply Construction Adhesive to Bottom of Base CB 8

9 B. INSTALL PLUMBING CAUTION: Risk of damage to bath bottom and subfloor. Ensure a watertight seal on the bath drain connections. 1. When the bath is securely positioned, connect the drain to the trap. NOTE: An access panel will simplify future maintenance. 2. Install the faucet valving and spout tee. Open the hot and cold water valves, and check the supply connections for leaks. 3. Run water into the bath, and check the drain connections for leaks. 7. ELECTRICAL CONNECTIONS A. IDENTIFY ELECTRICAL REQUIREMENTS The model number is printed on a label at the pump end of the whirlpool. The label identifies electrical rating. B. WIRING INFORMATION 120 V, 60 HZ 1-SPEED PUMP (UL LISTED) MODELS WARNING: Risk of electrical shock. To reduce the risk of electric shock, connect only to a properly grounded, grounding-type receptacle, protected by a Ground-Fault Circuit-Interrupter (GFCI). Do not remove the plug s grounding pin. Do not use a grounding adapter. Air Actuator Plug-in Cord 15 A Receptacle Your Kohler whirlpool bath is equipped with a cord and plug. All wiring of the pump and control has been completed at the factory. A licensed electrician must install a GFCI-protected, 120 V, 15 A, grounded outlet. Your whirlpool may then be plugged into this outlet. No other load should be on this circuit. Locate the outlet behind the whirlpool, and within 24 of the pump. NOTE: Be sure the air actuator tubing is securely attached to the pump. Ensure that it is not kinked or damaged. Air Actuator Tubing Pump Bonding (Earthing) Lug* * For bonding in accordance with national and local codes CB

10 8. WATER TEST WHIRLPOOL AND ELECTRONICS Check all electrical connections. Make sure all pipe connections to the pump are securely tightened. Fill the whirlpool to a level at least 2 above the top of the highest jet. Operate the whirlpool for 5 minutes, and check all whirlpool harness (piping) connections for leaks. For additional information on whirlpool operation, see Start-Up instructions on Page COMPLETE FINISH WALL CAUTION: Risk of product damage. Do not support the weight of the bath by the rim. Protect the whirlpool surface. Make sure the vinyl bead is attached securely to the sides being built into the wall. Cover the framing and walls with water-resistant wall material. Tape and mud the water-resistant wall material. Seal the wall material and joints under the whirlpool rim. Install the finish wall material. Seal the joints between the whirlpool rim and the finish wall using silicone sealant. RTV (Room Temperature Vulcanizing) sealant is recommended. É É É É Í ÇÇ ÇÇÍ Ç Finish Wall Covering Water-Resistant Wall Material Silicone Sealant Vinyl Bead 2x4 Studding Framing or Ledger Strip For installations that do not use a vinyl bead, cover the framing with water-resistant wall material as shown. Seal the joints between the whirlpool rim edge and the wall material with silicone sealant. Tape and mud the water-resistant wall material. Install the finish wall to the water-resistant wall material as shown. Seal the joints between the whirlpool rim and the finish wall material with silicone sealant. Silicone Sealant Finish Wall Material Water-Resistant Wall Material 10. COMPLETE INSTALLATION A. INSTALL HANDLES AND SPOUT After the deck is finished, attach the handles and spout to complete the faucet installation according to the faucet manufacturer s instructions CB 10

11 B. REMOVE PROTECTIVE FILM Carefully remove the clear protective film covering the whirlpool surface. 11. CLEAN-UP AFTER INSTALLATION When cleaning up after installation, do not use abrasive cleansers as they may scratch and dull the bath surface. Use warm water and a liquid detergent to clean the surface. Stubborn stains, paint, or tar can be removed with turpentine or paint thinner. Do not allow cleaners containing petroleum distillates to remain in contact with whirlpool surfaces for long periods of time. Plaster can be removed by scraping with a wood edge. Do not use metal scrapers, wire brushes, or other metal tools. A powder-type detergent may be used on a damp cloth to provide mild abrasive action to the residual plaster. 12. CONFIRM PROPER OPERATION A. START-UP WHIRLPOOL Refer to Important Safety Instructions on Page 2. Please perform the following so the owner can safely receive the benefits of whirlpool bathing. 1. Rotate the jets so they are facing down toward the basin. 2. Fill the whirlpool to a water level at least 2 above the top of the highest jet. Water temperature in the bath should not exceed 104 F (40 C). CAUTION: Risk of concealed leakage and product damage. Do not run this whirlpool without sufficient water in the bath. Running the pump dry may damage the pump and cause concealed water leakage. Never run the whirlpool without at least 2 to 3 of water covering the highest jet. Bath Wall 2 Minimum Jet Trim Water Line CB

12 B. OPERATING SEQUENCE 1. Turn on the whirlpool jets. Adjust the air control(s) for optimum air/water mixture. 2. Press the air actuator a second time to turn off the whirlpool. Turn on the whirlpool massage. TO METHOD OBSERVE Add air and water to whirlpool action, rotate the jet flange clockwise. To reduce air and water, rotate it counterclockwise. Add Air Reduce Air Shut off whirlpool. C. TROUBLESHOOT WHIRLPOOL SYSTEM This troubleshooting guide is for general aid only. A Kohler Authorized Service Representative or a qualified electrician should correct all electrical problems. For warranty service, contact your dealer or wholesale distributor. SYMPTOMS PROBABLE CAUSES RECOMMENDED ACTION 1. does not start/stop. 2. Motor starts, all jets are not functioning. 3. Motor turns, water is pumping, but there is no air injection. A. No power to pump. A. Set/Reset GFCI breaker; check wiring to pump. B. Faulty air switch in pump motor. B. Replace air switch in pump motor. C. Air actuator tubing disconnected, loose, kinked, plugged or damaged. C. Connect, straighten, clean or replace air actuator tubing. D. Faulty air actuator. D. Replace air actuator. E. Faulty motor/pump assembly. E. Rebuild or replace motor and pump assembly. A. Jet trim installed incorrectly. A. Reinstall jet trim. B. Jets are blocked. B. Remove blockage. C. Suction is blocked. C. Remove blockage. A. Air line obstructed. A. Clear obstruction, or replace air line. B. Suction is blocked. B. Remove blockage CB 12