IMAGE V. Parts and Service Manual

Size: px

Start display at page:

Download "IMAGE V. Parts and Service Manual"

Gertrude Shaw
5 years ago
Views:

1 IMAGE 0V Section II Parts and Service Manual (88B) CLARKE TECHNOLOGY Image Operator's Manual Page

2 AUTHORIZED PERSONNEL MAINTENANCE To Access Pump Motor. Remove brush housing from machine. See "Brush Motor Repair".. Remove pump ground wire from ground screw. 3. Disconnect pump electrical wires form machine harness.. Remove solution hoses by turning swivel nut counter clockwise.. Remove four () mounting screws that secure pump motor to solution tank.. Reverse procedures for installing new pump. Check wiring diagram for proper connections when reinstalling electrical parts. Solenoid/Spray Valve Removal. Loosen screw in rear plate that secures recovery tank to machine.. Raise and tilt recovery tank to the side. 3. Disconnect electrical lead from solution valve.. Disconnect solenoid from brush housing by press quick disconnect coupling on top of brush housing.. Remove hoses by loosening hose clamps and pull hoses from solenoid valve.. To reinstall, reverse procedure. Check wiring diagram for proper connections when reinstalling electrical parts. Brush Motor Repair. Tilt machine on handle or place machine upside down.. Pull brush adjustment rod out of adjustment holes. 3. Remove brush stop bracket by removing two () screws.. Remove two () brush pivot shoulder screws (3/" Allen Wrench) from sides of solution tank.. Pull brush housing away from solution tank far enough to access wiring.. Disconnect wiring and place brush housing on bench.. Remove bottom plate by removing nine (9) 0-3 screws. 8. Remove motor and reverse procedure to reinstall. 9. Check wiring diagram for proper connections when reinstalling electrical parts. Page 8 CLARKE TECHNOLOGY Image Operator's Manual

3 AUTHORIZED PERSONNEL MAINTENANCE (cont.) Brush Drive Belt Replacement. Tilt machine on handle or place machine upside down.. Remove bottom brush plate. 3. Remove pivot screw on drive sprocket side.. Remove drive sprocket and replace belt.. Reassemble in reverse order. Maintenance of the Vacuum Motor This machine has a vacuum motor that uses carbon brushes. The carbon brushes in the motor must be checked every three months, or every 00 hours of operation, whichever comes first. If either of the brushes is shorter than 3/8 inch, replace both of the carbon brushes. ¼ inches To gain access to the vacuum motor:. Remove one () screw in rear plate that secures recovery tank to machine.. Raise and tilt recovery tank. 3. Can now access the brushes or the three (3) bolts that secure the vacuum motor to tank. Figure Replacement of float switch. Install and tighten strain relief onto float cord. See fig... Install new o-ring seal onto strain relief. 3. Install replacement float with strain relief through inside wall of recovery tank.. Tighten strain relief.. Check wiring diagram for proper connections and check fittings for leaks.. Check float switch for proper operation and shut off capacity. Brush Maintenance (See page 3 for parts references). Tilt machine on handle or place machine upside down.. Remove one screw from each side (ref. # and #33 on page 3) of the brush housing. 3. Remove one screw (ref. # on page 3) from brush retainer strap (ref. #9 on page 3) and rotate strap so that brush can be removed.. Remove brush.. Carefully pry brush pivot out from bearing (applying pressure unevenly can break brush pivot).. Add a small amount of grease to face of seal and bearing on I.D. of brush core.. Reassemble in reverse order. Page 30 CLARKE TECHNOLOGY Image Operator's Manual

4 HOW TO CORRECT PROBLEMS IN THE MACHINE PROBLEM CAUSE ACTION The machine will not run.. Machine does not have power.... Make sure the machine is connected to the correct frequency and voltage, and all connections are tight. There is no suction.. Vacuum motor may not be running.... Be sure the vacuum/accessory switch for the vacuum motor is at the ON position.. Vacuum/accessory motor switch may be defective.. Contact an authorized service person. 3. There may be a loose motor 3. Contact an authorized service person. connection... There may be an obstruction in the. Remove the obstruction. vacuum hose.... Motor brushes may be worn.... Replace the motor brushes.. Drain valve may be open.... Close the drain valve.. Dome gasket may be worn or. Replace the gasket. damaged Vacuum hose may be damaged Replace the hose. 9. Vacuum intake screen clogged Remove and clean lint screen on vacuum stand pipe. Uneven or no spray from the. The spray/brush switch may be. Turn the switch to "I". jets. defective.... The spray tips may be dirty, plugged. Clean or replace the tips or worn The hose may be kinked Inspect the hose. The drain valve leaks.. The drain valve gaskets may be worn. Replace the gaskets. or damaged.... There may be lint or dirt in the drain. Clean or replace the drain valve. valve... The solution pump runs. The spray tips may be plugged.... Clean the spray tips. but no solution comes out of the spray nozzle. The spray solenoid may be damaged.... Replace spray solenoid. 3. The solution screen may be plugged Clean or replace the nozzle.. The pump may be worn.... Contact an authorized service person.. The hose may be kinked.... Inspect the hose. The solution pump leaks.. There may be a faulty seal in the pump.... Contact an authorized service person.. The pump may be worn.... Contact an authorized service person. The float switch may not. The switch may be damaged.... Contact an authorized service person. be shutting off or turning on. Brush motor doesn't run.. Circuit breaker tripped.... Reset circuit breaker.. Switch is bad.... Contact an authorized service person. 3. Motor is bad Contact an authorized service person. Page 3 CLARKE TECHNOLOGY Image Operator's Manual

5 Authentic CLARKE TECHNOLOGY Products 3 Item Part No. Description Qty 93A RM-P Tool Assembly 930A RM-8P Tool Assembly 3 98A RM-M Tool Assembly 99A RM-M Tool Assembly 3980 Defoamer * case 398 Extractor, Concentrate * case *, quart bottles CLARKE TECHNOLOGY Image Operator's Manual Page 3

6 CLARKE TECHNOLOGY Image i/ix Drawing Final Assembly / Page 3 CLARKE TECHNOLOGY Image Operator's Manual

7 CLARKE TECHNOLOGY Image i/ix Parts List, Final Assembly /99 Ref. Part No. Description Qty i ix Page 38 Asm., Recovery Shoe x x Page 3 Asm., Brush Housing x x 3 Page 3 Asm., Recovery Tank x x Page 3 Asm., Electrical Panel x Page 3 Asm., Electrical Panel x 90 Fuse Holder x x Page 39 Asm., Valve Support x x 99A Wheel x x Nut, PAL x x 9 3A Axle x x B Tank. Solution(incl. #'s,,0) x x 9R Motor, Vac, 3 Stage x x 08A Terminal, Male, Q.D. x x Washer, Lock 3 x x 9 Screw, 0- x ½ x x 83A Screw, ¼-0 x 3. Hx 3 x x 833A Spacer, 3 / Lg. Plastic 3 x x 83A Screw, 0-3 x ½ x x 8 38 Gasket x x Screw, 0- x ½ x x Cover, Solution Tank x x 80A Nut, 0- x x 909 Chain, Cover x x 3 89A Screw, ¼-0 x 3 /8 x x 93 Screw, 0-3 x x x Washer, Plain x x 9933 Terminal, Clip #0 Ring x x 90A Terminal, ¼ FIMQD* x x 8 90C Pump, 00 psi 0V x 98A Pump, 00 psi, Bypass x 9 09A Label, Ground Symbol x x Nut, 0-3 x x A Screw, 0-3 x 3 / x x 3 89A Cover, Bottom x x A Screw, ¼-0 x ½ x x 3 0 Hose, Exhaust x x Clamp Hose x x 3 Page 39 Assembly,Plate, Rear Cover x x 3 A Terminal, ¼ FIFQD** x x 38 80A Washer, Flat Nylon x x Washer, / Flat x x Washer, / Lock x x 883A Screw, / - 8 x x x 39A Adapter, 3 /8 Barb x ¼ NPT Nylon x x 3 93A Hose, Clear 3 /8 x 3" x x Screw, ¼-0 x ½ x x 8A Bushing x x A Connector x x 9A Fuse,.A x x Tag, Caution x x 9 89A Spacer, Recovery, Tool x x 0 A Bushing Drain x x 9800 Washer x x NI 990 Cable, Tie 9 x x NI 08A Literature Kit x x Accessories: Part No. A - Label Operating Instructions *FIMQD=Fully Insulated Male Quick Disconnect **FIFQD=Fully Insulated Female Quick Disconnect CLARKE TECHNOLOGY Image Operator's Manual Page 3

8 CLARKE TECHNOLOGY Image i/ix Drawing & Parts List, Recovery Tank Assembly /99 Form #983A Ref. Part No. Description Qty 3898C Tank, Recovery 9A Switch, Float 3 9A Strain, Relief 8330 O'Ring 909 Chain 833 Cover, Solution Tank 998 Screw, 0- x ½ 8 80A Nut, A Tube, Vacuum 0 89A Screw, ¼-0 x 3 /8 98A Washer, ½ NPT Sealing 3A Gasket, Cover 3 393A Tube, Recovery A Strainer 8300 Clamp, Plastic 303A Hose, Recovery 00 Clamp, Hose Screw, 8-8 x ½ 9 800A Lock Nut, ½ Conduit Drain, Valve 8330 Gasket, Drain Handle, Drain, Valve Screw, 0- x 3 /8 0A Chain 8390 Vavle Assembly ref. Page 38 CLARKE TECHNOLOGY Image Operator's Manual

9 CLARKE TECHNOLOGY Image i/ix Drawing and Parts List, Brush Housing Assembly /0 Form #8A Ref. Part No. Description Qty 33A Housing, Brush 9800 Washer, Wave 3 A Coupling Male QD 80A Washer ¼, Flat S.S. 8A Screw, 0- x ½ 80A Nut ¼ -0 8A Plate, Spray S.s. 8 8A Spacer 9 80A Terminal, #0 Ring 0 99 Pin, 3 / x ½ Roll 9090 Bolt, Shoulder 3 /8 x ½ x ½ 0C Motor, Brush Drive a 083A Brush Carton 3 8A Pulley 8B Plate, Brush 83A Screw, 0-3 x ½ S.S. 880A Housing, Spray Nozzle 339A Cap w/seal Assembly a 300A Gasket, Spray 8 A Nozzle, # x A Bracket, Brush Retainer 0 88B* Pivot, Brush **FIFQD=Fully Insulated Female Quick Disconnect *When servicing these items (#'s,, and ) see page Brush Maintenance a 8 A Ref. Part No. Description Qty 30A* Seal 908* Bearing 3K 8B Sprocket, 8T 33A Gasket, Brush 309A* Brush, Restoration a 300A Brush, Maintenance 98 Screw, Set 8-3 x 3 / 0909A Belt 8 0A Terminal, ¼ FIFQD** Washer, #0 Ext. Lock Nut, 0-3 Hex Spring 3 8B Rod, Brush Adjustment 33 80A Screw, 0- x ¾ SS 3 30A Bracket Brush Stop A Screw, 0x½ 3 380A Shield, Deflector 3 A Kit, Restoration, Brush includes Ref one of:(#0,,, ) 3A A Kit, Interim Brush includes Ref each of: (# 0,,, a) (ix model only) A Strainer NI 990 Cable Tie NOTE: Kindicates a change has taken place since last publication of this manual. CLARKE TECHNOLOGY Image Operator's Manual Page 39

10 CLARKE TECHNOLOGY Image i Drawing and Parts List, Electric Assembly /0 Form #3A Page 0 Ref. Part No. Description Qty 88A Screw, /" x ½ 9809 Washer, /" Flat B Handle, Control A Switch, Vacuum/Accessories A Switch, Spray/Brush 83A Screw, 0-3 x ½ 8383A Screw, 0-3 x ¾ Washer, #0 Ext. Lock 9 90 Nut, A Label, Ground Symbol 88A Cord, Power 3' A Terminal, ¼ FIFQD* Terminal, #0 Insulated Ring 803A Strain, Relief 080 Washer, /8 Flat 03A Rectifier 90 Nut, 0-3 Elastic Stop 8 8A Panel, Electrical 9 3B Breaker, Brush. A 0 800A Lock Nut, ½ Conduit 9A Cord, Harness Machine 9308 Screw, /" x 8 x ¼" Washer, 3 /8 Ext. Star 08A Cord Assembly, 3' NI 990 Cable Tie *FIFQD=Fully Insulated Quick Disconnect CLARKE TECHNOLOGY Image Operator's Manual

11 CLARKE TECHNOLOGY Image i/ix Drawing and Parts List, Recovery Shoe Assembly 8/00 Form # 9A/93A A 0 3 3, A 8 Ref. Part No. Description Qty i ix 80B Shoe, Recovery x x 30A Elbow, ¼ St x x 3 A Shoe, Recovery S.S. x x 800 Clamp, Hose x x 30A Manifold, Spray x x 980 Plug, ¼ Recess x x 303A Bracket, Manifold Retainer x x Screw, 0- x ½ 3 x x 9 880A Housing, Spray - x 9A A Nozzles 0 x. x A Nut, 0- Nylock S.S. 3 x x 30A Hose, Recovery x x 339A Cap w/gasket Asm. - x a 300A Gasket, Spray - x 3 A Nozzle, 0 x Brass Q.D. - x 9333 Screw, 0-3 x 3 /8 x x 90A Wire, Ground x x Washer, #0 Ext. Lock x x 30C Bracket, Brush Adj. x x 8 300A Strainer x x Page CLARKE TECHNOLOGY Image Operator's Manual

12 CLARKE TECHNOLOGY Image Drawing and Parts List, Valve Assembly /0 Form #9A , 3a, 3b, 3c Ref. Part No. Description Qty Ref. Part No. Description Qty 030 Clamp, Hose Washer, #0 Ext. Lock 30A Hose, Air " 90 Nut, 0-3 Hex Hosebarb 998 Screw, 0- x 3 /8 8A Support, Valve Elbow, Swivel 8390 Trim 3 9 3A Hose " 839A Screw, ¼-0 x ½ 0 98A Valve, Solution Flow 9800 Washer, S.S. 90A Tee Elbow 3A Elbow, ¼ NPT x 3 /8 Hosebarb 9 90 Reducer 3 038A Coupling, Female Q.D. shut-off 0 30 Quick Disconnect 083 Washer, flat 3 /8 3B Hose, ½" 300 Clip 39A Hosebarb, Nylon 09A Label, Ground Symbol 3 300A Strainer, Bowl (incl. #3a,b, c) 88A Plate, Rear, Cover 3a 80A Screen, Filter 8 908A Wire, Ground 3b 39A Gasket, Viton 3cK 008A Bowl, Filter 8383A Screw, 0-3 NOTE: K indicates a change has been made since the last publication of this manual. CLARKE TECHNOLOGY Image Operator's Manual Page 3

13 CLARKE TECHNOLOGY Image Drawing and Parts List /9 Pump (#90C) i model Pump (98A) ix model 3 90C 98A Ref. Part No. Description Qty 3A Kit, Switch - Viton 80/00psi x 30A Kit, Switch 80/00psi x 3A Kit, Dual Check Valves x 908A Kit, Check Valves x 3 88A Housing, Upper x x 33A Kit, Valve x 983A KIt, Valve x 30A Kit, Diaphragm x 30A KIt, Diaphragm x 88A Housing, Lower x x 83A KIt, Drive Assembly x 909A KIt, Drive Assembly x Page CLARKE TECHNOLOGY Image Operator's Manual

14 CLARKE TECHNOLOGY Image Drawing and Parts List /9 Motor (#9R) Ref. Part No. Description Qty * Nut * Housing Vent 3* Fan 8303A Screw, 8-3 x 3 /8 08A Brush, Mechanism 9A Clamp 08A Bracket, End, Com. 8* Bearing 9 Disc 0* Bearing * Washer * Bracket, Fan End 3* Spacer Ref. Part No. Description Qty * Fan, Rotating * Spacer * Fan, Stationary * Shell, Fan Spring, Load 9 399A Fan, Air Seal 0* Fan, Stationary * Fan, Rotating * Washer NOTE: #'s,,3,8,0,,,3,,,,,0,, are not available at this time. CLARKE TECHNOLOGY Image Operator's Manual Page

15 CLARKE TECHNOLOGY Image i/ix Electrical Schematic /99 Brush Circuit Breaker =. amp Fuse =. amp Page CLARKE TECHNOLOGY Image Operator's Manual

16 CLARKE TECHNOLOGY Image i/ix Connection Diagram /99 CLARKE TECHNOLOGY Image Operator's Manual Page

Electric Automatic Carpet Extractor. Operator and Parts Manual. Model No.: Rev. 00 (11-99)

1520 Electric Automatic Carpet Extractor Model No.: 607649 Operator and Parts Manual TENNANT COMPANY Commercial Products 12875 RANSOM STREET HOLLAND MI 49424 U.S.A. FAX: 1 800 678 4240 CUSTOMER SERVICE: