THE WALL-MOUNT AIR CONDITIONERS (50HZ)

Transcription

1 THE WALL-MOUNT AIR CONDITIONER (50HZ) Models W24A2 to W70A2 Right ide Control Panel Models W24L2 to W70L2 Left ide Control Panel 2,600 Btuh (6.33 KW) 62,000 Btuh (8.6 KW) For Export Only The Bard Wall-Mount Air Conditioner is a self contained energy efficient system, which is designed to offer maximum indoor comfort at a minimal cost without using valuable indoor floor space or outside ground space. This unit is the ideal product for versatile applications such as: new construction, modular offices, school modernization, telecommunication structures, portable structures or correctional facilities. Factory or field installed accessories are available to meet specific job requirements. Engineered Features Aluminum Finned Copper s: Grooved tubing and enhanced louvered fin for maximum heat transfer and energy efficiency. Twin Blowers: Move air quietly. Most models feature multispeed blower motors providing airflow adjustment for high and low static operation. Motor overload protection is standard on all models. Air Conditioner Compressor: croll Compressors eliminate need for crankcase heater. tandard on all models, except 5-Ton. R-40A Refrigerant: Designed with R-40A (HFC) non-ozone depleting refrigerant in compliance with the Montreal protocol and 0 EPA requirements. Phase Rotation Monitor: tandard on all 3 phase scroll compressors. Protects against reverse rotation if power supply is not properly connected. Galvanized Gauge Zinc Coated teel Cabinet: Cleaned, rinsed, sealed and dried before the polyurethane primer is applied. The cabinet is handsomely finished with a baked on textured enamel, which allows it to withstand 000 hours of salt spray tests per ATM B7-03. Foil Faced Insulation: tandard on all units. Full Length Mounting Brackets: Built into cabinet for improved appearance and easy installation. NOTE: Bottom mounting bracket included to assist in installation. Components: Are easily accessible for routine inspection and maintenance through a right side, service panel opening. Features a lockable, hinged access cover to the circuit breaker or toggle disconnect switch. Electric Heat trips: Features an automatic limit and thermal cut-off safety control. Filter ervice Door: eparate service door provides easy access for filter change. One Inch, Disposable Air Filters: Are standard equipment. Optional one inch washable filters available and filter racks permit the addition of 2" pleated filter. Factory or field installed. Condenser Fan and Motor hroud Assembly: lides out for easy access. Barometric Fresh Air Damper: tandard on all units. Allows up to 25% outside fresh air. Optional ventilation packages available. Built-in Circuit Breakers: tandard on all electric heat versions of single (2/8 volt) and three phase (2/8 volt) equipment. Toggle disconnects are standard on all electric heat versions of three phase (460 volt) equipment. lope Top: tandard feature for water run-off. Top Rain Flashing: tandard feature on all models. Liquid Line Filter Drier: tandard on all units. Protects system against moisture. Compressor Control Module: tandard on all units. Built-in off-delay timer adjustable from seconds to 5 minutes. 2-minute on-delay if power interrupt. -second bypass for low pressure control, and both soft and manual lockouts for high and low pressure controls. Alarm output for alarm relay. High & Low Pressure witches are Auto- Reset: tandard on all units. Built-in lockout circuit resets from the room thermostat. Provides commercial quality protection to the compressor. Bard is an IO 900:08 Certified Manufacturer Form No upersedes Page of 8

2 Capacity and Efficiency Ratings Models W24A2 W24L2 WA2 W36A2 W36L2 W42A2 W42L2 All capacity, efficiency and cost of operation is based on high speed operation with fresh air cover plate. Cover plate must be ordered separately and is recommended for use to obtain maximum energy efficiency where fresh air is not required. pecifications 2,0 Btuh (6.2 KW) 3,0 Btuh (9.4 KW) W48A2 W48L2 W60A2 W60L2 W70A2 W70L2 Cooling Capacity BTUH 2,600 26,800 32,000 36, ,000 50,000 62,000 Cooling Capacity KW EER MODEL W24A2-D W24A2-F W24L2-F WA2-D WA2-F W36A2-D W36A2-E W36A2-F W36L2-F Rating 50 Hz 240/2-45/380-3 j 240/2-45/380-3 j 240/2-2/0-3 45/380-3 j Operating Voltage Range Compressor--Circuit A Voltage 240/2 45/ /2 45/ /2 2/0 45/380 Rated Load Amps 8.2/ / / / /5.4.3/2.7 5./5.8 Branch Circuit election Current Lock Rotor Amps 60/60 28/28 67/67 38/38 87/87 95/95 46/46 Compressor Type croll croll croll croll croll croll croll Fan Motor & Condenser Fan Motor--HP--RPM /5-090 /5-090 /5-075 /5-075 /5-075 /5-075 /5-075 Fan Motor--Amps Fan--DIA m 3 /s 458/ / / / / / /0.78 Blower Motor & Evap. Blower Motor--HP-RPM-PD /6-00- /6-00- / / / / / Blower Motor--Amps m 3 /s Cooling & E..P. (pa) w/filter (Rated- ) 0.32/ / / / / / /50 Filter izes (mm) TD. 405x6x25 405x6x25 405x765x25 405x765x25 405x765x25 405x765x25 405x765x25 hipping Weight --LB. (Kg) 3 (52) 3 (52) 375 (70) 375 (70) 375 (70) 375 (70) 375 (70) pecifications 36,000 Btuh (0.54 KW) 59,000 Btuh (7.28 KW) MODEL W42A2-E W42A2-F W42L2-F W48A2-E W48A2-F W48L2-F W60A2-E W60A2-F W60L2-F W70A2-F W70L2-F Rating 50 Hz 2/0-3 45/380-3 j 2/0-3 45/380-3 j 2/0-3 45/380-3 j 45/380-3 j Operating Voltage Range Compressor--Circuit A Voltage 2/0 45/380 2/0 45/380 2/0 45/380 45/380 Rated Load Amps 0./.3 4.8/ / /6.4 3/ / /9. Branch Circuit election Current Lock Rotor Amps 80.7/ /43 0/0 5.5/5.5 0/0 5.5/5.5 74/74 Compressor Type croll croll croll croll croll croll croll Fan Motor & Condenser Fan Motor--HP--RPM /3-825 /3-825 /3-825 /3-825 /3-825 /3-825 /3-950 Fan Motor--Amps Fan--DIA m 3 /s 60/.05 60/.05 60/.05 60/.05 60/ / /.37 Blower Motor & Evap. Blower Motor--HP-RPM-PD / / / / / / / Blower Motor--Amps m 3 /s Cooling & E..P. (pa) w/filter (Rated- ) 0.55/2 0.55/2 0.60/ / / / /50 Filter izes (mm) TD. 508x765x25 508x765x25 508x765x25 508x765x25 508x765x25 508x765x25 508x765x25 hipping Weight --LB. (Kg) 525 (238) 525 (238) 525 (238) 525 (238) 525 (238) 525 (238) 525 (238) j 45/380-3 electrical ratings are 3-phase wye (star) systems requiring three (3) phase legs plus neutral and ground. NOTE: The indoor & outdoor motors and 24V transformer primary are connected at 240V derived from one () phase leg to neutral. This is internally connected and no field wiring required. Unit Charge Rates - R40A Form No upersedes Page 2 of 8 UNIT td. Unit - Lbs. W24A2/L2-9 EER Right & Left A/C WA2/L2-9 EER Right & Left A/C 4.25 W36A2/L2-9 EER Right & Left A/C W42A2/L2-9 EER Right & Left A/C UNIT td. Unit - Lbs. W48A2/L2-9 EER Right & Left A/C W60A2/L2-9 EER Right & Left A/C 6.25 W70A2/L2-9 EER Right & Left A/C 6.750

3 Ventilation ystem Packages Bard Wall-Mounts are designed to provide optional ventilation packages to meet all of your ventilation and indoor air quality requirements. All units are equipped with a barometric fresh air damper as the standard ventilation package. All ventilation packages can be built-in at the factory or field-installed at a later date. BAROMETRIC FREH AIR DAMPER - BFAD TANDARD The barometric fresh air damper is a standard feature on all models. It is installed on the inside of the service door and allows outside ventilation air, up to 25% of the total airflow rating of the unit, to be introduced through the air inlet openings and to be mixed with the conditioned air. The damper opens during blower operation and closes when the blower is off. Adjustable blade stops allow different amounts of outside air to be introduced into the building and can be easily locked closed if required. MI-3754 Barometric Fresh Air Damper BLANK OFF PLATE - BOP OPTIONAL A blank off plate is installed on the inside of the service door. It covers the air inlet openings, which restricts any outside air from entering the unit. The blank off plate should be utilized in applications where outside air is not required to be mixed with the conditioned air. MOTORIZED FREH AIR DAMPER - MFAD OPTIONAL The motorized fresh air damper is internally mounted behind the service door and allows outside ventilation air, up to 25% of the total airflow rating of the unit, to be introduced through the air inlet openings and to be mixed with the conditioned air. The two position damper can be fully open or closed. The damper blade is powered open by a 24VAC motor with spring return on power loss. The damper can be controlled by indoor blower operation or can be field connected to be managed based on building occupancy. Motorized Fresh Air Damper MI-3755 NOTE: The above vent systems are intake only without built-in exhaust capability. Building will likely require separate field installed barometric relief or mechanical exhaust elsewhere within the conditioned space. Balancing dampers in the return air grille may be required to achieve specified amount of outdoor air intake. Commercial Room Ventilator MI-3756 COMMERCIAL ROOM VENTILATOR - CRV OPTIONAL The built-in commercial room ventilator is internally mounted behind the service door and allows outside ventilation air, up to 00% of the total airflow rating of the unit, to be introduced through the air inlet openings. It includes a built-in exhaust air damper. The commercial room ventilator (CRV) is a simple and innovative approach to improving the indoor air quality by providing fresh air intake and exhaust capability through the CRV. The damper can be easily adjusted to control the amount of fresh air supplied into the building. The CRV can be controlled by indoor blower operation or field controlled based on room occupancy. The CRV is power open - spring return on power loss. Complies with ANI/ AHRAE tandard 62. Ventilation for Acceptable Indoor Air Quality. tandard Features: Fully modulating Honeywell Hi-Torque Actuator No hood required imple single blade design Positive shut-off with non-stick gaskets olid tate Controller with occupancy CFM setting Economizer MI-3757 ECONOMIZER WECO eries OPTIONAL The built-in economizer system is internally mounted behind the service door and allows outdoor air to be introduced through the air inlet openings. The amount of outdoor air varies in response to the system controls and settings defined by the end user. It includes a built-in exhaust air damper. The economizer is designed to provide free cooling when outside air conditions are cool and dry enough to satisfy cooling requirements without running the compressor. This in turn provides lower operating costs, while extending the life of the compressor. tandard Features: Full rated outdoor intake Fully modulating Honeywell Hi-Torque Actuator " Intake hood with filter imple single blade design Positive shut-off with non-stick gaskets Electronic DB and/or Enthalpy sensors depending upon version Honeywell JADE electronic economizer module with precision settings and diagnostics DB or Enthalpy economizer versions available Form No upersedes Page 3 of 8

4 Clearances - Inches (mm) Required for ervice Access and Adequate Condenser Inlet Airflow MODEL LEFT IDE RIGHT IDE W24A2, WA2, W36A2 5" (380) " (50) W42A2, W48A2, W60A2, W70A2 " (50) " (50) Minimum Clearances - Inches (mm) Required to Combustible Materials MODEL UPPLY AIR DUCT FIRT THREE FEET (m) CABINET W24A2 0" 0" WA2, W36A2 /4" (6.) 0" W42A2, W48A2, W60A2, W70A2 /4" (6.) 0" Refer to the Installation Manual for more detailed information. Dimensions of Basic Unit for Architectural & Installation Requirements - Inches (mm) MODEL W24A2 WA2 W36A2 W42A2 W48A2 W60A2 W70A2 WIDTH (W) 33.0 (845) 38.0 (970) (069) (069) DEPTH (D) 7.25 (4) 7.25 (4) (570) (570) HEIGHT (H) (792) (792) (256) (256) UPPLY RETURN A B C B E F G I J K L M N O P Q R T (0) (505) (2) (505) (889) (0) (708) (3) (708) (06) (25) (759) (403) (759) (5) (25) (759) (403) (759) (5) 0.88 (276) 0.88 (276) 3.56 (344) 3.56 (344) (654) (522) (680) (73) (743) (654) (455) (680) (7) (743) (804) (762) (8) (684) (88) (804) (762) (8) (684) (88) (686) (686) (824) (824) 2.63 (67) 2.75 (0) 3.37 (86) 3.37 (86) 34.3 (867) 39.9 (996) (560) (578) (089) (607) (089) (607) 0.55 (268) 9.4 (232) 0.00 (254) 0.00 (254) 4.9 (06) 4.9 (06) 2.00 (5) 2.00 (5) 2.00 (5) 2.00 (5) 6.00 (406) 6.00 (406) 5.00 (27) 5.00 (27).88 (48).88 (48) W24A2-70A2 Models W Built In Rain Hood 4 Pitch Heater Access Panel Electric Heat C. Breaker/ Disconnect Access Panel (Lockable) D 2.3 A I ide Wall Mounting Brackets (Built In) Top Rain Flashing hipping Location E O upply Air Opening B.44 R 5.88 F G Filter Access Panel Ventilation Air Condenser Air Outlet tandard flush vent door for non-econ. models " Low Voltage Hood for ECONWMT Entrance models. High Voltage Entrance Cond. Air Inlet J C K H Optional Entrances L M P Return Air Opening T Front View ide View Drain N Q Back View Bottom Installation Bracket MI-3282 Not used when WECO Economizers installed. Filter access is through the WECO hood. Form No upersedes Page 4 of 8

5 Clearances - Inches (mm) Required for ervice Access and Adequate Condenser Inlet Airflow MODEL LEFT IDE RIGHT IDE W24L2, WL2, W36L2 5" (380) " (50) W42L2, W48L2, W60L2, W70L2 " (50) " (50) Minimum Clearances - Inches (mm) Required to Combustible Materials MODEL UPPLY AIR DUCT FIRT THREE FEET (m) CABINET W24L2 0" 0" WL2, W36L2 /4" (6.) 0" W42L2, W48L2, W60L2, W70L2 /4" (6.) 0" Refer to the Installation Manual for more detailed information. Dimensions of Basic Unit for Architectural & Installation Requirements - Inches (mm) MODEL W24L2 WL2 W36L2 W42L2 W48L2 W60L2 W70L2 WIDTH (W) 33.0 (845) 38.0 (970) (069) (069) DEPTH (D) 7.25 (4) 7.25 (4) (570) (570) HEIGHT (H) (792) (792) (256) (256) UPPLY RETURN A B C B E F G I J K L M N O P Q R T (0) (505) (2) (505) (889) (0) (708) (3) (708) (06) (25) (759) (403) (759) (5) (25) (759) (403) (759) (5) 0.88 (276) 0.88 (276) 3.56 (344) 3.56 (344) (654) (522) (680) (73) (743) (654) (455) (680) (7) (743) (804) (762) (8) (684) (88) (804) (762) (8) (684) (88) (686) (686) (824) (824) 2.63 (67) 2.75 (0) 3.37 (86) 3.37 (86) 34.3 (867) 39.9 (996) (560) (578) (089) (607) (089) (607) 0.55 (268) 9.4 (232) 0.00 (254) 0.00 (254) 4.9 (06) 4.9 (06) 2.00 (5) 2.00 (5) 2.00 (5) 2.00 (5) 6.00 (406) 6.00 (406) 5.00 (27) 5.00 (27).88 (48).88 (48) W24L2-70L2 Models R Built In Electric E Rain Hood Heat Heater O 4 Pitch Access.44 Panel D C. Breaker/ W 2.3 Disconnect Access Panel ide Wall upply Air Opening (Lockable) Mounting A Brackets tandard flush (Built In) vent door for B non-econ. models Top Rain Flashing hipping Location I Return Air Opening Optional Entrances C Filter Access Panel Ventilation Air 5.88 F T Drain Bottom Installation Bracket Back View Q P M N L H K J Cond. Air Inlet ide View " Hood for ECONWMT models. Low Voltage Entrance High Voltage Entrance Condenser Air Outlet Front View G MI-3283 Not used when WECO Economizers installed. Filter access is through the WECO hood. Form No upersedes Page 5 of 8

6 pecifications MODEL W24A2-D0Z D05 D08 W24A2/L2-F0Z F05 WA2-D0Z D05 D0 WA2-F0Z F2 W36A2-D0Z D05 D0 W36A2-E0Z E06 E2 W36A2/L2-F0Z F2 W42A2-E0Z E09 E5 W42A2/L2-F0Z F4 W48A2-E0Z E09 E5 W48A2/L2-F0Z F4 W60A2-E0Z E09 E5 W60A2/L2-F0Z F4 W70A2/L2-F0Z F4 Rated Volts & Phase Operating Voltage Range 240/ /380-3 l / /380-3 l / / /380-3 l / /380-3 l / /380-3 l / /380-3 l /380-3 l No. Field Power Circuits k Minimum Circuit Amps j Maximum External Fuse or Circuit Breaker Maximum size of the time delay fuse or D rated circuit breaker for protection of field wiring conductors. k These Minimum Circuit Amp values are to be used for sizing the field power conductors. l 45/380-3 Ratings are 3-phase wye (star) systems requiring three (3) phase legs plus neutral and ground. NOTE: The indoor and outdoor motors and 24V transformer primary are connected at 240V derived from one () phase leg to neutral. This is internally connected and no field wiring required. NOTE: All wiring must conform to NIC/EIC latest edition. IMPORTANT: While this electrical data is presented as a guide, it is important to electrically connect properly sized fuses & conductor wires in accordance with the National Code & all local codes Electric Heat Table - Refer to pecifications for Availability by Unit Model Model W24A2-D W24A2-F W24L2-F WA2-D W36A2-D W36A2-E WA2-F W36A2-F W36L2-F W42A2-E W48A2-E W60A2-E W42A2-F, W42L2-F W48A2-F, W48L2-F W60A2-F, W60L2-F W70A2-F, W70L2-F KW 240V- 2V- 45V-3 380V-3 240V- 2V- 2V-3 0V-3 45V-3 380V-3 2V-3 0V-3 45V-3 380V Nominal Heater KW based on unit model number. Form No upersedes Page 6 of 8

7 Cooling Application Data - Outdoor Temperature Btuh (KW) Indoor Blower Performance - CFM (m 3 /s) at 2 Volts peed Model W24A2 W24L2 WA2 W36A2 W36L2 W42A2 W42L2 W48A2 W48L2 W60A2 W60L2 W70A2 W70L2 Return Air (DB/WB) (23.9/6.7 C) (26.7/9.4 C) (23.9/6.7 C) (26.7/9.4 C) (23.9/6.7 C) (26.7/9.4 C) (23.9/6.7 C) (26.7/9.4 C) (23.9/6.7 C) (26.7/9.4 C) (23.9/6.7 C) (26.7/9.4 C) (23.9/6.7 C) (26.7/9.4 C) Cooling Capacity 75 F (23.9 C) 22,600 (6.62) 8,00 (5.) 24,00 (7.06) 7,500 (5.3 27,900 (8.7) 2,400 ( ,700 (8.70),800 (6.09) 33,600 ( ,00 (7.4),900 (0.5) 24,400 (7.5) 40,00 (.74) 3,400 (9.) 42,700 (2.5),400 (8.90) 47,700 (3.97) 36,0 (0.60) 50,900 (4.9),00 (0.28) 52,700 (5.43) 40,0 (.80) 56,0 (6.49) 39,00 (.45) 66,0 (9.39) 46,800 (3.7) 70,700 (.7) 45,400 (3.) W24A2/L2 WA2/L2 W36A2/L2 85 F (29.4 C),800 (6.09) 7,0 (5.04) 23,00 (6.77) 7,000 (4.98) 25,600 (7.50) 2,0 (6.2) 28,400 (8.32),900 (6.2),800 (9.02) 24,00 (7.06) 34,0 (0.02) 23,800 (6.97),700 (0.46) 29,800 (8.73) 39,600 (.60) 29,500 (8.64) 43,400 (2.7) 34,400 (0.07) 48,0 (4.2) 34,00 (9.99) 48,00 (4.09) 38,0 (.9) 53,400 ( ,800 (.07) 59,700 (7.48) 44,0 (2.97) 66,0 (9.42) 43,800 (2.83) Below 65 F (8.3C), unit requires a factory or field installed low ambient control. Return air temperature. 95 F (.0 C) 9,000 (5.56) 6,0 (4.77) 2, 600 (6.33) 6,400 (4.80) 23,0 (6.82),0 (5.95) 26,800 (7.85),500 (6.00) 28,000 (8.) 22,900 (6.7) 32,000 (9.38) 23,00 (6.77) 32,0 (9.43) 28,0 (8.29) 36,800 (0.78) 28,500 (8.) 39,0 (.5) 32,600 (9.55) 45,000 (3.8) 32,900 (9.64) 43,600 (2.77) 36,00 (0.57) 50,000 (4.65) 36,400 (0.66) 53,900 (5.79) 4,800 (2.24) 62,000 (8.6) 42,0 (2.36) W42A2/L2 W48A2/L2 05 F (40.6 C) 7,0 (5.04) 5,400 (4.5),0 (5.92) 5,800 (4.63) 2,0 (6.24) 9,0 (5.65) 25,000 (7.32) 9,700 (5.77) 25,0 (7.4) 2,500 (6.) 29,900 (8.76) 22,00 (6.47) 29,0 (8.58) 26,800 (7.85) 34,500 (0.0) 27,400 (8.02),500 (0.40),600 (8.96) 4,900 (2.27) 3,400 (9.) 39,500 (.57) 34,00 (9.99) 46,600 (3.65),000 (0.25) 48,900 (4.32) 39,400 (.54) 57,700 (6.90) 40,400 (.83) W60A2/L2 5 F (46. C) 5,0 (4.45) 4,500 (4.25) 8,0 (5.36) 5,00 (4.42) 9,0 (5.62) 7,800 (5.2) 23,000 (6.74) 8,500 (5.42) 22,800 (6.68),000 (5.86) 27,400 (8.02),800 (6.09) 27,00 (7.94) 25,00 (7.) 32,500 (9.52) 26,00 (7.64) 32,000 (9.37) 28,600 (8.38) 38,500 (.28) 29,800 (8.73),600 (0.43) 32,0 (9.46) 42,800 (2.54) 33,500 (9.8) 44,500 (3.03) 36,900 (0.8) 53,600 (5.70) 38,400 (.25) 25 F (5.7 C) 3,0 (3.90) 3,600 (3.98) 6,0 (4.74) 4,0 (4.6) 7,000 (4.98) 6,000 (4.69),600 (6.03) (4.92),0 (5.95) 8,400 (5.39) 24,700 (7.23) 9,0 (5.65) 25,0 (7.4) 23,400 (6.85),800 (9.02) 24,600 (7.) 28,500 (8.) 26,600 (7.79) 34,700 (0.6) 28,000 (8.) 3,800 (9.3),400 (8.90) 38,700 (.33) 3,900 (9.34) 40,600 (.89) 34,500 (0.0) 49,600 (4.53) 36,400 (0.66) W70A2/L2 ingle High Low High Low High Low High Low High Low EP (Inch H) (Pa) 0.0 (0) 8 (0.39) 805 (0.38) (0.54) 065 (0.50) (0.) (0.50) 795 (0.38) (0.72) 495 (0.7) 3 (0.63) 290 (0.6) 725 (0.8) 670 (0.79) 250 (0.59) (0.57) 700 (0.80) 5 (0.72) 2 (0.58) (25) 785 (0.37) (0.5) 05 7 (0.) 75 (0.34) (0.53) (0.37) (0.70) 4 (0.67) 280 (0.60) 245 (0.59) 675 (0.79) 625 (0.77) 5 (0.57) 65 6 (0.77) 470 (0.69) 85 (0.56) 0 (0.52) 0.2 (50) 740 (0.) 7 (0.34) (0.44) 705 (0.33) 675 (0.32) 050 (0.50) 9 (0.44) (0.) 400 (0.66) 360 (0.64) (0.57) (0.76) 550 (0.73) (0.53) 580 (0.75) 40 (0.67) 40 (0.54) 075 (0.5) 0.3 (75) 680 (0.32) 665 (0.3) 925 (0.44) 845 (0.40) 655 (0.3) 625 (0.29) 990 (0.47) 880 (0.42) 725 (0.34) 705 (0.33) 3 (0.62) 285 (0.6) 55 5 (0.53) 550 (0.73) 505 (0.7) 0 (0.52) 080 ( (0.72) 365 (0.64) (0.45) 0.4 (00) 60 (0.29) 600 (0.28) 8 (0.39) (0.27) 550 (0.26) 900 (0.42) 80 (0.38) 645 (0.) 625 (0.29) 240 (0.59) (0.57) 085 (0.5) 055 (0.50) 455 (0.69) 45 (0.67) (0.46) 4 (0.67) 285 (0.6) 945 (0.45) 890 (0.42) Above data is with " (25mm) standard disposable filter and " (25mm) washable filter. For optional 2" (5mm) pleated filter - reduce EP by.5" (37.33Pa). ee installation instructions for maximum EP information on various KW application. peeds marked bold above are Factory Connected. Form No upersedes Page 7 of 8

8 Air Conditioning Wall-Mount Model Nomenclature ERIE NOMINAL CAPACITY 24-2 Ton - 2½ Ton 36-3 Ton 42-3½ Ton 48-4 Ton 60-5 Ton 70-6 Ton W 36 A 2 D 0 X X X X X X Ventilation Options Models Description REVIION TYPE A = Compressor & Controls - Right ide L = Compressor & Controls - Left ide VOLT & PHAE D - 240/2/50/ E - 2/0/50/3 F - 45/380/50/3 Factory Installed Code No. Insert color to match unit ("X" = Beige; "4" = Buckeye Gray; etc.) All Economizer versions have 7" deep intake hood. KW VENTILATION OPTION (ee Table Below) FILTER OPTION X - -Inch (25mm) Disposable (tandard) W - -Inch (25mm) Washable P - 2-Inch (5mm) Pleated W24A2 W24L2 Field Installed Part No. Factory Installed Code No. COLOR OPTION X - Beige (tandard) - White 4 - Buckeye Gray 5 - Desert Brown 8 - Dark Bronze A - Aluminum WA2 W36A2, W36L2 Field Installed Part No. CONTROL MODULE (ee Chart Below) COIL OPTION X - tandard - Phenolic Coated Evaporator 2 - Phenolic Coated Condenser 3 - Phenolic Coated Evaporator and Condenser UPPLY AIR OUTLET X - Front (tandard) ee pecifications (Page 6). Aftermarket corrosion resistance coating is necessary for installations in a corrosive environment or coastal area where the unit will be exposed to salt water. W42A2, W48A2, W60A2, W70A2 W42L2, W48L2, W60L2, W70L2 Factory Installed Field Installed Code No. Part No. Barometric Fresh Air Damper - tandard X WBFAD-2 X WBFAD-3 X WBFAD-5 Blank-Off Plate B WBOP-2 B WBOP-3 B WBOP-5 Motorized Fresh Air Damper w/plug M WMFADP2 M WMFADP3 M WMFADP5 Commercial Ventilator - pring Return w/plug & Exhaust V WCRVP2-* V WCRVP3-* V WCRVP5-* Economizer w/plug, Temp Only W WECOPT2-* W WECOPT3-* W WECOPT5-* Economizer w/plug, Enthalpy T WECOPE2-* T WECOPE3-* T WECOPE5-* Air Conditioning Control Modules All Models Except As Noted HPC LPC CCM LAC ALR K K ODT DDC Factory Installed Code Field Installed Part TD TD TD X N/A TD TD TD E CMA-28 TD TD TD J Factory Only TD TD TD K CMC-5 and CMA-28 TD TD TD M Factory Only TD TD TD N N/A TD TD TD Field Installed Only CMC-5 TD TD TD Field Installed Only CMA-4 TD TD TD V 0 Factory Only CMA-3 for W8-36 TD TD TD Field Installed Only CMA- for W42-70 K Except W60 & 70 TD TD TD Field Installed Only K2 W70 Only K22 W60 Only TD = tandard equipment for these specified models. HPC. High pressure control is auto reset. Always used with compressor control module (CCM) which is included. ee note. LPC. Low pressure control is auto reset. Always used with compressor control module (CCM) which is included. ee note. CCM. Compressor control module has adjustable -second to 5-minute delay-on-break timer. On initial power-up, or any time the power is interrupted, the delay-on-make will be 2-minutes plus 0% of the delay-on-break setting. There is no delay-on-make during routine operation of the unit. The module also provides the lockout feature (with retry) for high and/or low pressure controls, and a 2-minute timed bypass for low-pressure control. LAC. Low ambient control permits cooling operation down to 0 F. LAC is fan-cycling control for outdoor fan motor on all models except W8/W24 Dehum. units, which have modulating control. ALR. The alarm relay has a set of normally open and normally closed dry contacts to provide the ability to signal a condition of shutdown on either high or low pressure controls. K. PTCR start kit can be used with all -A single phase models. Increases starting torque 2-3x. Not used for -B or -C three phase models. Do not use if K or K2 is used. K. tart capacitor & potential relay start kit can be used with all -A single phase models. Increases starting torque 9x. Not used for -B or -C three phase models. Do not use if CMC-5 is used. ODT. Outdoor thermostat is adjustable from 0 to 50 F. It is suitable for use as a compressor cut-off thermostat. DDC. Incorporates 4 additional sensors: discharge air temperature, indoor blower airflow, compressor current, and dirty filter. These sensing devices function to input analog data such as temperature, as well as digital data such as airflow, compressor status or filter status. pecial economizer required; consult factory. V control module should be ordered in conjunction with direct digital controller (DDC). Refer to V module document F605 for more information. Bard Manufacturing Company, Inc. Bryan, Ohio ince Moving ahead, just as planned. Due to our continuous product improvement policy, all specifications subject to change without notice. Before purchasing this appliance, read important energy cost and efficiency information available from your retailer. Form No June 8 upersedes: Form No upersedes Page 8 of 8