T P A 048 S 4 N 4 1 T

Transcription

1 E N G I N E E R I N G D ATA H E A T P U M P O U T D O O R U N I T S TP T-Class Split System Units R-40A - 50 HZ Bulletin No September 2009 MODEL NUMBER IDENTIFICATION Nominal Capacity - 7 to 7.6 kw (2 to 5 Ton) Cooling Capacity to 7.6 kw (2 800 to Btuh) Heating Capacity to 4.4 kw (2 000 to Btuh) T P A 048 S 4 N 4 T Family T = Product Line Unit Type P = Heat Pump Outdoor Unit Major Design Sequence A= First Generation B = Second Generation Nominal Cooling Capacity 024 = 7.0 kw (2 tons) 030 = 8.8 kw (2.5 tons) 036 = 0.5 kw (3 tons) 048 = 4. kw(4 tons) 060 = 7.6 kw (5 tons) Refrigerant Type 4 = R-40A Coil Type 4 = Four-sided Voltage T = 220/240V-phase-50hz M = 380/420-3phase-50hz Minor Design Sequence = First revision 2 = Second Revision 3 = Third Revision Part Load Capability N = No part load, single-stage compressor Cooling Efficiency S = Standard Efficiency

2 FEATURES AND BENEFITS Contents Dimensions...9 Expanded Ratings - Single Phase Models... Expanded Ratings - Three Phase Models...7 Features And Benefits...2 Installation Clearances...5 Model Number Identification... Optional Control Systems....8 Ratings...0 Sound Data....5 Specifications - Single Phase...6 Specifications - Three Phase...7 G B J C I A E F TESTING Rated at test conditions included in Air-Conditioning, Heating and Refrigeration Institute (AHRI) Standard 20/240 when operating at rated voltage and air volumes. Units tested by Intertek for conformity assessment on the conditions set out in the New Approach Directives in support of CE marking. The CE (Conformité Européenne) marking certifies that a product has met EU (European Union) consumer safety, health or environmental requirements. Units and components within bonded for grounding to meet safety standards for servicing required by Underwriters Laboratories (UL) and the International Electrotechnical Commission (IEC). International Organization for Standardization (ISO) 900 Registered Manufacturing Quality System APPLICATIONS 7 to 7.6 kw. Single or three phase power supply. Vertical air discharge allows concealment behind shrubs at grade level or out of sight on a roof. Designed for applications with remotely located indoor air handler units or gas furnaces (dual-fuel) with indoor add-on coils. See s and Air Handlers sections for indoor unit data. Units shipped completely factory assembled, piped and wired. Each unit is test operated at the factory insuring proper operation. Installer must set outdoor unit, connect refrigerant lines and make electrical connections to complete job. REFRIGERATION SYSTEM R-40A Refrigerant Non-chlorine, ozone friendly, R-40A. Unit pre-charged with refrigerant. 50 hz T-Class Heat Pumps 7 to 7.6 kw / Page 2 D H See Specification table. Unit is factory pre-charged with refrigerant. system refrigerant charge is dependant on outdoor unit size, indoor unit size and refrigerant line length. Refer to Installation Instructions for Indoor Unit MatchUp and Sub-Cooling Charge Levels to determine correct amount of charge required. B Outdoor Coil Fan Direct drive fan moves large air volumes uniformly through entire condenser coil for high refrigerant cooling and heating capacity. Vertical air discharge minimizes operating sounds and eliminates damage to lawn and shrubs. Louvered steel top fan guard furnished as standard. Fan service access accomplished by removal of top panel.

3 C D E F FEATURES AND BENEFITS Copper Tube/Enhanced Fin Coil Lennox designed and fabricated coil. Ripple-edged aluminum fins. Copper tube construction. Lanced fins provide maximum exposure of fin surface to air stream resulting in excellent heat transfer. Fin collars grip tubing for maximum contact area. Flared shoulder tubing connections/silver soldering construction. Coil is factory tested under high pressure to ensure leakproof construction. Entire coil is accessible for cleaning. Polyvinyl Chloride (PVC) coated steel wire coil guard furnished. Expansion Valve - Outdoor Unit Designed and sized specifically for use in heat pump system. Sensing bulb is located on the suction line between the reversing valve and the compressor to sense evaporator suction temperature in any cycle. Factory installed and piped. High Pressure Switch Protects the system from high pressure conditions that can be a result of fan failure or a blocked/dirty coil. Automatic reset. Loss of Charge Switch Helps protect the compressor from damage due low refrigerant charge conditions. Single-pole, single-throw (SPST), normally-closed switch, automatic reset switch mounted on suction line. High Capacity Liquid Line Drier Factory installed in the liquid line, the drier traps moisture or dirt that could contaminate the refrigerant system. 00% molecular-sieve, bead type bi-flow drier. Reversing Valve 4-way interchange reversing valve effects a rapid change in direction of refrigerant flow resulting in quick changeover from cooling to heating and vice versa. Valve operates on pressure differential between outdoor unit and indoor unit of the system. Factory installed. OPTIONS Check/Expansion Valve Kits Must be ordered extra and field installed on certain indoor units. Chatleff-style fittings. G H Refrigerant Line Kits Refrigerant lines (suction & liquid) are shipped refrigeration clean. Lines are cleaned, dried, pressurized and sealed at factory. Suction line fully insulated. Lines are stubbed at both ends. Not available for -060 models. Must be field fabricated. CABINET Heavy gauge steel cabinet with five station metal wash process. Powder paint finish provides superior rust and corrosion protection. Painted base section. Control box is conveniently located with all controls factory wired. Corner patch plate allows access to compressor components. Drainage holes are provided in base section for moisture removal. Refrigerant Line Connections, Electrical Inlets, Service Valves Sweat connection vapor and liquid lines are located on corner of unit cabinet. Fully serviceable brass service valves prevent corrosion and provide access to refrigerant system. Vapor valve can be fully shut off, while liquid valve may be front seated to manage refrigerant charge while servicing system. Refrigerant line connections and field wiring inlets are located in one central area of cabinet for easy access. See dimension drawing. OPTIONS Hail Guards Constructed of louvered, heavy-gauge steel painted to match cabinet. Surrounds unit on all four sides to prevent damage to the coil. Mounting Base Provides permanent foundation for outdoor units. High density polyethylene structural material is lightweight, sturdy, sound absorbing and will withstand the rigors of the sun, heat, cold, moisture, oil and refrigerant. Will not mildew or rot. Can be shipped singly or in packages of 6 to a carton. Unit Stand-Off Kit Black high density polyethylene feet are available to raise unit off of mounting surface away from damaging moisture. Four feet are furnished per order number. 50 hz T-Class Heat Pumps 7 to 7.6 kw / Page 3

4 I FEATURES AND BENEFITS COMPRESSOR Scroll Compressor Compressor features high efficiency with uniform suction flow, constant discharge flow and high volumetric efficiency and quiet operation. Compressor consists of two involute spiral scrolls matched together to generate a series of crescent shaped gas pockets between them. During compression, one scroll remains stationary while the other scroll orbits around it. Gas is drawn into the outer pocket, the pocket is sealed as the scroll rotates. As the spiral movement continues, gas pockets are pushed to the center of the scrolls. Volume between the pockets is simultaneously reduced. When pocket reaches the center, gas is now at high pressure and is forced out of a port located in the center of the fixed scrolls. During compression, several pockets are compressed simultaneously resulting in a smooth continuous compression cycle. Continuous flank contact, maintained by centrifugal force, minimizes gas leakage and maximizes efficiency. Scroll compressor is tolerant to the effects of slugging and contaminants. If this occurs, scrolls separate, allowing liquid or contaminants to be worked toward the center and discharged. Low gas pulses during compression reduces operational sound levels. Compressor motor is internally protected from excessive current and temperature. Muffler in discharge line reduces operating sound levels. Compressor is installed in the unit on resilient rubber mounts for vibration free operation. Factory installed crankcase heater protects against refrigerant migration that can occur during low ambient operation. OPTIONS Compressor Sound Cover A reinforced vinyl compressor cover containing a 38 mm thick batt of fiberglass insulation. All open edges are sealed with a 25 mm wide hook and loop fastening tape. J CONTROLS Defrost Control Solid-state time/temperature defrost control is furnished as standard equipment. Control initiates a defrost cycle every 30, 60 or 90 minutes of compressor on time at outdoor coil temperatures below 5 C (factory setting 90 minutes). Anti-short cycle, timed-off control incorporated into the board. High and low pressure switch monitoring with five-trip lockout. Diagnostic light emitting diodes (LED s) furnished as an aid in troubleshooting. Conveniently located in control box. OPTIONS Compressor Hard Start Kit Single-phase units are equipped with a permanent split capacitor (PSC) compressor motor. This type of motor normally doesn t need a potential relay and start capacitor. In conditions such as low voltage, this kit may be required to increase the compressor starting torque. Compressor Low Ambient Cut-Off Non-adjustable switch (low ambient cut-out) prevents compressor operation when outdoor temperature is below 2 C. Freezestat Installs on or near the vapor line of the indoor coil or on the suction line. Senses suction line temperature and cycles the compressor off when suction line temperature falls below it s setpoint. Opens at -2 C and closes at 4 C. Indoor Blower Off Delay Relay Delays the indoor blower-off time during the cooling cycle. See Ratings Table for usage. Low Ambient Kit Heat pump in the cooling mode will operate satisfactorily down to 7 C outdoor air temperature without any additional controls. Low Ambient Control Kit can be field installed, allowing unit operation down to - C. Freezestat should be installed on compressors equipped with a low ambient kit. A Compressor Low Ambient Cut-Off should be added to terminate compressor operation below recommended operating conditions. 50 hz T-Class Heat Pumps 7 to 7.6 kw / Page 4

5 FEATURES AND BENEFITS CONTROLS (CONTINUED) OPTIONS Low Pressure Switch Bypass Thermostat For use in applications where the heat pump is operated in outdoor ambient temperatures below -9 C. Prevents nuisance trips from the low pressure switch. Wired in parallel with the low pressure switch. Mild Weather Kit Heat pump units operate satisfactorily in the heating mode at outdoor air temperatures up to 24 C. Mild Weather Kit can be field installed, allowing heating operation above 24 C. Monitor Kit - Service Light Contains ambient compensating thermistor and service light thermostat. For use with thermostats requiring input for indicator lights. Outdoor Thermostat Kit An outdoor thermostat can be used to lock out some of the electric heating elements on indoor units where two stage control is applicable. Outdoor thermostat maintains the heating load on the low power input as long as possible before allowing the full power load to come on the line. Thermostat kit and mounting box must be ordered extra. Thermostat Thermostat is not furnished with unit and must be ordered extra. See Page 8. INSTALLATION CLEARANCES - MM (INCHES) See NOTES See NOTES See NOTES See NOTES CONTROL BOX NOTES: Service clearance of 762 mm (30 in.) must be maintained on one of the sides adjacent to the control box. Clearance to one of the other three sides must be 94 mm (36 in.) Clearance to one of the remaining two sides may be 305 mm (2 in.) and the final side may be 52 mm (6 in.). A clearance of 60 mm (24 in.) must be maintained between two units. 29 mm (48 in.) clearance required on top of unit. SOUND DATA Unit Model No. Octave Band Sound Power Levels dba, re 0-2 Watts Center Frequency - HZ Sound Rating Number (db) 220/240V - Single Phase Models TPA024S TPA036S TPA048S /420V - Three Phase Models TPA036S TPA048S TPA060S NOTE - the octave sound power data does not include tonal correction. Tested at conditions included in Air-Conditioning, Heating and Refrigeration Institute (AHRI) Standard test. 50 hz T-Class Heat Pumps 7 to 7.6 kw / Page 5

6 SPECIFICATIONS - SINGLE PHASE General Model No. TPA024S4 TPA036S4 TPA048S4 Data Nominal kw Connections Liquid line o.d. - in. 3/8 3/8 3/8 (sweat) Vapor line o.d. - in. 3/4 7/8 7/8 Refrigerant (R-40A) furnished 2.95 kg (6 lbs. 8 oz.) 2.86 kg (6 lbs. 5 oz.) 5.30 kg ( lbs. oz.) Outdoor Coil Outdoor Fan Net face area Outer coil.4 (5.2).4 (5.2).96 (2.) m 2 (sq. ft.) Inner coil (5.50).98 (2.3) Tube diameter - in. 5/6 5/6 5/6 Number of rows 2 2 Fins per meter (inch) 866 (22) 866 (22) 866 (22) Diameter - mm (in.) 457 (8) 457 (8) 559 (22) Number of blades Motor W (hp) 49 (/5) 49 (/5) 248 (/3) L/s (Cfm) 945 (2000) 965 (2042) 530 (3242) Rev / min Watts Shipping Data - kg (lbs.) package 64 (40) 82 (80) 3 (250) Electrical Data Line voltage data - 50 hz - ph 220 / 240V 220 / 240V 220 / 240V 2 Maximum overcurrent protection (amps) Minimum circuit ampacity Compressor Rated load amps Locked rotor amps Power factor...7 Outdoor Full load amps Fan Motor Locked rotor amps OPTIONAL ACCESSORIES - must be ordered extra Compressor Hard Start Kit 0J42 88M9 Compressor Low Ambient Cut-Off 45F08 Compressor Sound Cover 69J03 Freezestat 3/8 in. tubing 93G35 5/8 in. tubing 50A93 Hail Guards 92M88 92M90 Indoor Blower Off Delay Relay 58M8 4 Low Ambient Kit 54M89 Low Pressure Switch Bypass 3W07 Thermostat Mild Weather Kit 33M07 Monitor Kit - Service Light 76F53 Mounting Base 69J06 69J07 Outdoor Thermostat Thermostat 56A87 Kit Mounting Box 346 Refrigerant Line Sets L5-4-20, L5-4-30, L5-4-40, L L , L , L Field Fabricate Unit Stand-Off Kit 94J45 NOTE - Extremes of operating range are plus 0% and minus 5% of line voltage. Refrigerant charge sufficient for 4.6 m (5 ft.) length of refrigerant lines. 2 Heating, air conditioning and refrigeration (HACR) type circuit breaker or fuse. 3 Refer to local codesl to determine wire, fuse and disconnect size requirements. 4 Freezestat is recommended with Low Ambient Kit. 50 hz T-Class Heat Pumps 7 to 7.6 kw / Page 6

7 SPECIFICATIONS - THREE PHASE General Model No. TPA036S4 TPA048S4 TPA060S4 Data Nominal kw Connections Liquid line o.d. - in. 3/8 3/8 3/8 (sweat) Vapor line o.d. - in. 7/8 7/8 -/8 Refrigerant (R-40A) furnished 2.86 (6 lbs. 5 oz.) 5.30 ( lbs. oz.) 6.24 (3 lbs. 2 oz.) Outdoor Net face area Outer coil.4 (5.2).96 (2.) 2.28 (24.50) Coil m 2 (sq. ft.) Inner coil.44 (5.50).98 (2.3) 2.9 (23.56) Tube diameter - in. 5/6 5/6 5/6 Number of rows Fins per meter (inch) 866 (22) 866 (22) 866 (22) Outdoor Fan Diameter - mm (in.) 457 (8) 559 (22) 559 (22) Number of blades Motor W (hp) 25 (/6) 250 (/3) 85 (/4) L/s (Cfm) 965 (2042) 530 (3242) 505 (392) Rev / min Watts Shipping Data - kg (lbs.) package 82 (80) 3 (250) 6 (255) Electrical Data Line voltage data - 50 hz - 3ph 380 / 420V 380 / 420V 380 / 420V 2 Maximum overcurrent protection (amps) Minimum circuit ampacity Compressor Rated load amps Locked rotor amps Power factor Outdoor Full load amps Fan Motor Locked rotor amps OPTIONAL ACCESSORIES - must be ordered extra Compressor Hard Start Kit 0J42 88M9 Compressor Low Ambient Cut-Off 45F08 Compressor Sound Cover 69J03 Freezestat 3/8 in. tubing 93G35 5/8 in. tubing 50A93 Hail Guards 92M88 92M90 92M94 Indoor Blower Off Delay Relay 58M8 4 Low Ambient Kit 54M89 Low Pressure Switch Bypass Thermostat 3W07 Mild Weather Kit 33M07 Monitor Kit - Service Light 76F53 Mounting Base 69J06 69J07 Outdoor Thermostat Thermostat 56A87 Kit Mounting Box 346 Refrigerant Line Sets L , L , L Field Fabricate Unit Stand-Off Kit 94J45 NOTE - Extremes of operating range are plus 0% and minus 5% of line voltage. Refrigerant charge sufficient for 4.6 m (5 ft.) length of refrigerant lines. 2 Heating, air conditioning and refrigeration (HACR) type circuit breaker or fuse. 3 Refer to local codes to determine wire, fuse and disconnect size requirements. 4 Freezestat is recommended with Low Ambient Kit. 50 hz T-Class Heat Pumps 7 to 7.6 kw / Page 7

8 OPTIONAL CONVENTIONAL TEMPERATURE CONTROL SYSTEMS - FIELD INSTALLED COMMERCIAL TOUCHSCREEN THERMOSTAT Intuitive Touchscreen Interface - Two Stage Heating / Two Stage Cooling Conventional or Heat Pump - Seven Day Programmable - Four Time Periods/ Day - Economizer Output - Title 24 Compliant - ENERGY STAR Qualified - Backlit Display - Automatic Changeover C0STAT02AEL (4W8) Sensors For Touchscreen Thermostat Remote non-adjustable wall mount 20k temperature sensor... C0SNZN0AE2- (47W36) Remote non-adjustable wall mount 0k averaging temperature sensor... C0SNZN73AE- (47W37) Remote non-adjustable duct mount temperature sensor... C0SNDC00AE- (9L22) Outdoor temperature sensor... C0SNSR03AE- (X448) Accessories For Touchscreen Thermostat Locking cover (clear)... C0MISC5AE- (39P2) Remote sensors for C0STAT02AEL can be applied in the following combinations: () C0SNZN0AE-, (2) C0SNZN73AE-, (2) C0SNZN0AE- and () C0SNZN73AE-, (4) C0SNZN0AE-, (3) C0SNZN0AE- and (2) C0SNZN73AE. DIGITAL NON-PROGRAMMABLE THERMOSTATS Intuitive Interface - Automatic Changeover - Simple Up and Down Control Two-stage heating / cooling conventional systems... C0STAT0AEL (3K98) Sensor For Digital Non-Programmable Thermostats Above Remote wall mounted temperature sensor... C0SNZN00AE- (26K57) Intuitive Interface - Automatic Changeover - Backlit Display - Simple Up and Down Control One-stage heating / cooling conventional systems... C0STAT2AEL (5M32) Sensor For Digital Non-Programmable Thermostats Above Outdoor temperature sensor... C0SNSR04AE- (X2658) Accessories For Digital Non-Programmable Thermostats Above Optional wall mounting plate... C0MISC7AE- (X2659) 50 hz T-Class Heat Pumps 7 to 7.6 kw / Page 8

9 DIMENSIONS - MM (INches) (4-3/8) (4-3/8) INLET AIR (4-3/8) (4-3/8) INLET INLET OPTIONAL UNIT STAND-OFF KIT (4) (Field Installed) COMPRESSOR AIR AIR COIL DRAIN OUTLETS (Around perimeter of base) VAPOR LINE CONNECTION 62 (6-3/8) (4-3/8) INLET AIR TOP VIEW LIQUID LINE CONNECTION 62 (6-3/8) (4-3/8) TOP VIEW BASE SECTION A CONDENSER COIL FAN DISCHARGE A AIR COMPRESSOR C B SUCTION & LIQUID LINE CONNECTIONS ELECTRICAL INLETS 5 (2 ) 70 (2-3/4) SIDE VIEW 9 (3/4) OPTIONAL UNIT STAND-OFF KIT (4) (Field Installed) SIDE VIEW Model No. A B C mm inches mm inches mm inches TPA024S4 TPA036S / / /2 TPA048S / /4 TPA060S / / /2 50 hz T-Class Heat Pumps 7 to 7.6 kw / Page 9

10 RATINGS Net Cooling and Heating Ratings Outdoor Capacity Unit Model Number SINGLE PHASE Cooling High Temp. Heating Low Temp. Heating Capacity Capacity Power Power Power Coefficient of Performance Energy Efficiency Ratio Coefficient of Performance kw Btuh kw kw Btuh kw kw Btuh kw Coefficient of Performance Indoor Unit Model Number Expansion Device Required TPA024S BCRMA7924S005 49L24 TPA024S CX34-8/24A/B/C Factory TPA024S CH33-25B-2F 49L24 TPA024S CR33-24B-F 49L24 TPA036S BCRMB9937S005 49L24 TPA036S CX34-38B-6F Factory TPA036S CH33-36C-2F 49L24 TPA036S CR33-30/36B-F 49L24 TPA048S BCRMC9960S005 9M02 TPA048S CX34-44/48C-6F Factory TPA048S CH33-48C-2F 9M02 TPA048S CR33-50/60C-F 9M02 THREE PHASE TPA036S BCRMB9937S3N5 49L24 TPA036S CX34-38B-6F Factory TPA036S CH33-36C-2F 49L24 TPA036S CR33-30/36B-F 49L24 TPA048S BCRMC9960S4N5 49L24 TPA048S CX34-44/48C-6F Factory TPA048S CH33-48C-2F 49L24 TPA048S CR33-50/60C-F 49L24 TPA060S BCRMD960S4N5 9M02 TPA060S CX34-62D-6F Factory TPA060S CH33-62D-2F 9M02 TPA060S CR33-60D-F 9M02 The rating test conditions are those included in Air-Conditioning, Heating and Refrigeration Institute (AHRI) Standard 20/ while operating at rated voltage and air volumes. Cooling Ratings: 35 C (95 F) outdoor air temperature, 26.7 C (80 F) dry bulb and 9.4 C (67 F) wet bulb entering evaporator air with 6.0 m (20 feet) of connecting refrigerant lines. Net Cooling Capacity = Gross Cooling Capacity Heat added by indoor blower motor [0.47 m 3 /s or 3.43 Btu/W (365W per 000 cfm)] on blower coils All ratings include the use of a blower time delay relay (TDR). Furnaces and Air Handlers may require an optional time delay relay (58M8) for field installation. See furnace or air handler specifications to determine if relay is needed. 50 hz T-Class Heat Pumps 7 to 7.6 kw / Page 0

11 EXPANDED RATINGS - SINGLE PHASE MODELS NOTE For s and Capacities not shown in tables, see bulletin Cooling Unit Rating Table Correction Factor Data in Miscellaneous Engineering Data section. TPA024S4 Cooling Capacity with BCRMA7924S005 Air Comp. Sensible To Comp. Sensible To Comp. Sensible To Comp. Sensible To Dry Dry Dry Dry TPA024S4 Heating Capacity with BCRMA7924S TPA024S4 Cooling Capacity with CX34-8/24A/B/C-6F Air Comp. Sensible To Comp. Sensible To Comp. Sensible To Comp. Sensible To Dry Dry Dry Dry TPA024S4 Heating Capacity with CX34-8/24A/B/C-6F hz T-Class Heat Pumps 7 to 7.6 kw / Page

12 EXPANDED RATINGS - SINGLE PHASE MODELS NOTE For s and Capacities not shown in tables, see bulletin Cooling Unit Rating Table Correction Factor Data in Miscellaneous Engineering Data section. TPA024S4 Cooling Capacity with CH33-25A-2F Air Comp. Sensible To Comp. Sensible To Comp. Sensible To Comp. Sensible To Dry Dry Dry Dry ` TPA024S4 Heating Capacity with CH33-25A-2F TPA024S4 Cooling Capacity with CR33-24B-F Air Comp. Sensible To Comp. Sensible To Comp. Sensible To Comp. Sensible To Dry Dry Dry Dry TPA024S4 Heating Capacity with CR33-24B-F hz T-Class Heat Pumps 7 to 7.6 kw / Page 2

13 EXPANDED RATINGS - SINGLE PHASE MODELS NOTE For s and Capacities not shown in tables, see bulletin Cooling Unit Rating Table Correction Factor Data in Miscellaneous Engineering Data section. TPA036S4 Cooling Capacity with BCRMB9937S005 Air Comp. Sensible To Comp. Sensible To Comp. Sensible To Comp. Sensible To Dry Dry Dry Dry TPA036S4 Heating Capacity with BCRMB9937S TPA036S4 Cooling Capacity with CX34-38B-6F Air Comp. Sensible To Comp. Sensible To Comp. Sensible To Comp. Sensible To Dry Dry Dry Dry TPA036S4 Heating Capacity with CX34-38B-6F hz T-Class Heat Pumps 7 to 7.6 kw / Page 3

14 EXPANDED RATINGS - SINGLE PHASE MODELS NOTE For s and Capacities not shown in tables, see bulletin Cooling Unit Rating Table Correction Factor Data in Miscellaneous Engineering Data section. TPA036S4 Cooling Capacity with CH33-36C-2F Air Comp. Sensible To Comp. Sensible To Comp. Sensible To Comp. Sensible To Dry Dry Dry Dry TPA036S4 Heating Capacity with CH33-36C-2F TPA036S4 Cooling Capacity with CR33-30/36B-F Air Comp. Sensible To Comp. Sensible To Comp. Sensible To Comp. Sensible To Dry Dry Dry Dry TPA036S4 Heating Capacity with CR33-30/36B-F hz T-Class Heat Pumps 7 to 7.6 kw / Page 4

15 EXPANDED RATINGS - SINGLE PHASE MODELS NOTE For s and Capacities not shown in tables, see bulletin Cooling Unit Rating Table Correction Factor Data in Miscellaneous Engineering Data section. TPA048S4 Cooling Capacity with BCRMC9960S005 Air Comp. Sensible To Comp. Sensible To Comp. Sensible To Comp. Sensible To Dry Dry Dry Dry TPA048S4 Heating Capacity with BCRMC9960S TPA048S4 Cooling Capacity with CX34-44/48C-6F Air Comp. Sensible To Comp. Sensible To Comp. Sensible To Comp. Sensible To Dry Dry Dry Dry TPA048S4 Heating Capacity with CX34-44/48C-6F hz T-Class Heat Pumps 7 to 7.6 kw / Page 5

16 EXPANDED RATINGS - SINGLE PHASE MODELS NOTE For s and Capacities not shown in tables, see bulletin Cooling Unit Rating Table Correction Factor Data in Miscellaneous Engineering Data section. TPA048S4 Cooling Capacity with CH33-48C-2F Air Comp. Sensible To Comp. Sensible To Comp. Sensible To Comp. Sensible To Dry Dry Dry Dry TPA048S4 Heating Capacity with CH33-48C-2F TPA048S4 Cooling Capacity with CR33-50/60C-F Air Comp. Sensible To Comp. Sensible To Comp. Sensible To Comp. Sensible To Dry Dry Dry Dry TPA048S4 Heating Capacity with CR33-50/60C-F hz T-Class Heat Pumps 7 to 7.6 kw / Page 6

17 EXPANDED RATINGS - THREE PHASE MODELS NOTE For s and Capacities not shown in tables, see bulletin Cooling Unit Rating Table Correction Factor Data in Miscellaneous Engineering Data section. TPA036S4 Cooling Capacity with BCRMB9937S3N5 Air Comp. Sensible To Comp. Sensible To Comp. Sensible To Comp. Sensible To Dry Dry Dry Dry TPA364S4 Heating Capacity with BCRMB9937S3N TPA036S4 Cooling Capacity with CX34-38B-6F Air Comp. Sensible To Comp. Sensible To Comp. Sensible To Comp. Sensible To Dry Dry Dry Dry TPA036S4 Heating Capacity with CX34-38B-6F hz T-Class Heat Pumps 7 to 7.6 kw / Page 7

18 EXPANDED RATINGS - THREE PHASE MODELS NOTE For s and Capacities not shown in tables, see bulletin Cooling Unit Rating Table Correction Factor Data in Miscellaneous Engineering Data section. TPA036S4 Cooling Capacity with CH33-36C-2F Air Comp. Sensible To Comp. Sensible To Comp. Sensible To Comp. Sensible To Dry Dry Dry Dry TPA036S4 Heating Capacity with CH33-36C-2F TPA036S4 Cooling Capacity with CR33-30/36B-F Air Comp. Sensible To Comp. Sensible To Comp. Sensible To Comp. Sensible To Dry Dry Dry Dry TPA036S4 Heating Capacity with CR33-30/36B-F hz T-Class Heat Pumps 7 to 7.6 kw / Page 8

19 EXPANDED RATINGS - THREE PHASE MODELS NOTE For s and Capacities not shown in tables, see bulletin Cooling Unit Rating Table Correction Factor Data in Miscellaneous Engineering Data section. TPA048S4 Cooling Capacity with BCRMC9960S4N5 Air Comp. Sensible To Comp. Sensible To Comp. Sensible To Comp. Sensible To Dry Dry Dry Dry TPA048S4 Heating Capacity with BCRMC9960S4N TPA048S4 Cooling Capacity with CX34-44/48C-6F Air Comp. Sensible To Comp. Sensible To Comp. Sensible To Comp. Sensible To Dry Dry Dry Dry TPA048S4 Heating Capacity with CX34-44/48C-6F hz T-Class Heat Pumps 7 to 7.6 kw / Page 9

20 EXPANDED RATINGS - THREE PHASE MODELS NOTE For s and Capacities not shown in tables, see bulletin Cooling Unit Rating Table Correction Factor Data in Miscellaneous Engineering Data section. TPA048S4 Cooling Capacity with CH33-48C-2F Air Comp. Sensible To Comp. Sensible To Comp. Sensible To Comp. Sensible To Dry Dry Dry Dry TPA048S4 Heating Capacity with CH33-48C-2F TPA048S4 Cooling Capacity with CR33-50/60C-F Air Comp. Sensible To Comp. Sensible To Comp. Sensible To Comp. Sensible To Dry Dry Dry Dry TPA048S4 Heating Capacity with CR33-50/60C-F hz T-Class Heat Pumps 7 to 7.6 kw / Page 20

21 EXPANDED RATINGS - THREE PHASE MODELS NOTE For s and Capacities not shown in tables, see bulletin Cooling Unit Rating Table Correction Factor Data in Miscellaneous Engineering Data section. TPA060S4 Cooling Capacity with BCRMD960S4N5 Air Comp. Sensible To Comp. Sensible To Comp. Sensible To Comp. Sensible To Dry Dry Dry Dry TPA060S4 Heating Capacity with BCRMD960S4N TPA060S4 Cooling Capacity with CX34-62D-6F Air Comp. Sensible To Comp. Sensible To Comp. Sensible To Comp. Sensible To Dry Dry Dry Dry TPA060S4 Heating Capacity with CX34-62D-6F hz T-Class Heat Pumps 7 to 7.6 kw / Page 2

22 EXPANDED RATINGS - THREE PHASE MODELS NOTE For s and Capacities not shown in tables, see bulletin Cooling Unit Rating Table Correction Factor Data in Miscellaneous Engineering Data section. TPA060S4 Cooling Capacity with CH33-62D-2F Air Comp. Sensible To Comp. Sensible To Comp. Sensible To Comp. Sensible To Dry Dry Dry Dry TPA060S4 Heating Capacity with CH33-62D-2F TPA060S4 Cooling Capacity with CR33-60D-F Air Comp. Sensible To Comp. Sensible To Comp. Sensible To Comp. Sensible To Dry Dry Dry Dry TPA060S4 Heating Capacity with CR33-60D-F hz T-Class Heat Pumps 7 to 7.6 kw / Page 22

23

24 Visit us at For the latest technical information, Contact us at LENNOX NOTE - Due to Lennox ongoing commitment to quality, Specifications, Ratings and Dimensions subject to change without notice and without incurring liability. Improper installation, adjustment, alteration, service or maintenance can cause property damage or personal injury. Installation and service must be performed by a qualified installer and servicing agency Lennox Industries, Inc.