User's Guide. ExStik DO600. Dissolved Oxygen Meter RECALL. Dissolved Oxygen DO600
|
|
- Kelley Stevenson
- 5 years ago
- Views:
Transcription
1 User's Guide ExStik DO600 Dissolved Oxygen Meter II RECALL Dissolved Oxygen DO600
2 Introduction Congratulations on your purchase of the ExStik DO600 dissolved oxygen / temperature meter which simultaneously displays dissolved oxygen and temperature. Units of measure are % saturation, mg/l or ppm for dissolved oxygen, and C or F for temperature. Advanced features include Data Hold, 25 points memory, auto power off, automatic temperature compensation, salinity and altitude compensation. This meter is shipped fully tested and calibrated and, with proper use, will provide years of reliable service. Meter Description Front Panel Description 1. Battery compartment cover 2. LCD Display 3. MODE/HOLD button 4. CAL/RECALL button 5. ON/OFF button 6. Electrode Retaining Collar 7. Dissolved Oxygen Sensor 8. Bonded Membrane Cap assembly 9. Membrane & Cathode (Note: The Electrode storage cap is not shown) Electrode Bottom View Cathode Membrane RECALL Dissolved Oxygen DO600 II LCD Display 1. Bar graph display 2. Measurement units 3. Main display 4. Low Battery indicator 5. Temperature display 6. Reading hold indicator 2
3 Operation Prepare the Electrode 1. The electrode is shipped dry and requires filling with the supplied electrolyte solution before use. The membrane should be in place and does not need replacement. Follow the procedure at the end of this guide for filling the bonded cap. Powering the ExStik The ExStik uses four (4) CR2032 Lithium Ion Batteries. Press the ON/OFF button to turn the meter on or off. If the batteries are weak, the BAT indicator appears on the LCD. The auto power off feature shuts the ExStik off automatically after approximately 10 minutes of inactivity. The auto power off feature may be temporarily disabled for convenience or for extended polarization time. Startup Polarization Period When the ExStik is powered up for the first time, the electrode requires polarization. In order for this to occur a three minute (approx.) polarization period must elapse before measurements can be made. A special circuit is included in this meter which, upon turn-on, maintains a very small biasing current to the electrode for a period of seven days. This keeps the electrode polarized and enables the user to make immediate measurements (within a 7 day period) without waiting for the electrode to re-polarize. Each time the ExStik is turned on, the polarization timer is reset and the 7 day polarization period is initiated. A small asterisk at the bottom right corner of the display is used to indicate that the polarization timer circuit is active. If the ExStik is not used for more than seven day, a 3 minute waiting period is required before a measurement can be made. Turn- Diagnostics 2. When the meter is turned ON the LCD displays SELF and CAL while the meter runs a diagnostic routine. 3. During this time the meter is recalling the User Calibration data, performing self diagnostics & initializing the circuitry. 4. After this function is complete, the meter proceeds to the normal measurement mode. Measurements 1. Cover the electrode with the electrode cap. The sponge contained in the cap should be moistened (not soaked) with DI (distilled water) or clean tap water. 2. Pressing the ON/OFF button turns the meter ON or OFF. When turned ON, the meter s display switches on and the Self Calibration utility runs (see above). The unit of measure selected when the meter was last turned OFF will remain on the display. 3. If this is the first time the meter is powered up, wait approx. 3 minutes for the probe to polarize (please disable auto-power off; Instructions for disabling auto-power off are provided in a later section). For more details, please read the Startup Polarization Period paragraph earlier in this manual before continuing. 4. Select the desired units of measure by pressing and holding the MODE/HOLD button until the proper units are shown in the display. Remove the electrode cover and place the electrode in the sample to be measured. Stir the electrode in the sample to remove any trapped air bubbles from the membrane surface. Do not submerse the electrode to the point that the sample liquid reaches the meter s electrode collar. 5. Allow the meter time to settle to the final measurement value. Note: The larger the difference in temperature between the electrode and the solution the longer it will take for the reading to stabilize. Stabilization time can vary from ten (10) seconds to five (5) minutes. 3
4 Calibration 1. Calibration should be performed on a daily basis. 2. Turn the meter ON 3. Press and hold the MODE/HOLD button until % is displayed on the LCD. 4. If the meter has not been used for seven (7) days or longer, allow the electrode to fully polarize. This may take 2-3 minutes. 5. Place the electrode cap onto the electrode. The sponge contained in the cap should be moistened (not soaked) with DI (distilled water) or clean tap water. Be sure that the electrode membrane is clean and dry or the calibration will be incorrect. Never touch the membrane, as skin oil will affect the electrode response. 6. Wait until the reading stabilizes then press and hold the CAL/RECALL button until CAL is shown in the lower display. The readings will blink and SA will appear. 7. When the calibration is complete End will appear and then the meter will return to the normal measurement mode. Note: The SA will not appear if the calibration fails. 8. Optional zero oxygen calibration (improves measurement accuracy for very low or very high DO measurements): Place the electrode in a zero oxygen calibration solution, such as 5% sodium sulfite, wait for stability and press the CAL/RECALL button until CAL is shown in the in the lower display. Stability in a zero solution may take many minutes, depending on electrode history. Note: Sodium Sulfite can become deposited on the electrode and on the coined surface of the electrode retaining collar. The presence of the Sodium Sulfite will negatively affect future DO measurements until such a time where ALL of it is removed from the electrode. Measurement Units The meter can be set to measure % saturation, dissolved oxygen in mg/l, and dissolved oxygen in parts per million (ppm). To change the mode: 1. Press and hold the MODE/HOLD button for 2 seconds and the display will begin to scroll through the different units of measure : % saturation; D.O. in mg/l; D.O. in ppm (parts per million) 2. When the desired units are displayed, release the MODE/HOLD button and the unit will return to normal operating mode. Note: The HOLD function cannot be on when changing the measurement function. If HOLD is displayed in the lower left corner of the display, briefly press the MODE/HOLD button to turn it off. Temperature Units (ºF / ºC) 1. With the unit OFF, press and hold the CAL/RECALL button. 2. With the CAL/RECALL button depressed, momentarily press the ON/OFF button to turn the unit ON. 3. The CAL/RECALL button can be released when Self Cal is shown in the display. Salinity Compensation 1. With the unit ON, momentarily press the CAL/RECALL button twice in quick succession ( SAL is shown in the lower temperature display). 2. Momentary press the MODE/HOLD button. Each press of the MODE/HOLD button increases the compensation by 1ppt (part per thousand); the available range is 0 to 50ppt. 3. Momentarily press the CAL/RECALL button to save the compensation setting and return to the normal measurement mode. 4
5 Altitude Compensation 1. With the unit ON, momentarily press the CAL/RECALL button twice in quick succession ( SAL is shown in the lower temperature display. 2. Press and hold CAL/RECALL again for 2 seconds to enter the Altitude Mode ( Ald will be shown in the lower temperature display). 3. The factory default value is sea level. Each press of the MODE/HOLD button increases the compensation by 1000ft. The maximum value is 20 presses (20,000ft above sea level). 4. Momentarily press the CAL/RECALL button to save the compensation setting and return to the normal measurement mode. Auto-Power OFF Feature The auto power off feature automatically shuts the meter off 10 minutes after the most recent button press. To disable this feature, refer to the Disable Auto-Power OFF section. Disable Auto-Power OFF Feature With the unit ON, momentarily press the CAL/RECALL button, then quickly press and hold both the MODE/HOLD and ON/OFF buttons until off is displayed. To restore the Auto Power Off Feature (auto power OFF enable) simply turn the meter off and on again using the ON/OFF button. Low Battery Indication When the battery voltage falls below the operating threshold, BAT will appear on the display. Refer to the Maintenance section for battery replacement information. Storing Readings 1. Press the MODE/HOLD button to store a reading. The storage location number will be displayed on the lower display, while the main display shows the stored reading. The meter will enter the HOLD mode and the HOLD indicator will appear on the LCD. 2. Press the MODE/HOLD button again to exit the HOLD mode and return to normal operation. The next time MODE/HOLD is momentarily pressed another reading is stored and so on. 3. If more than 25 readings are stored, previously stored readings (starting with reading number 1) are overwritten. Recalling Stored Readings 1. Momentarily press the CAL/RECALL button and then with in 4 seconds momentarily press the MODE/HOLD. The last stored data point location will be displayed (1 to 25). Each time the MODE/HOLD button is momentarily pressed the next most recently stored data point will be displayed. 2. After the last data point stored is displayed, pressing the MODE/HOLD button again returns the display to the beginning of the list. 3. Pressing the CAL/RECALL button at anytime stops the data retrieval process and returns the meter to the normal measurement mode. Clearing Stored Readings 1. With the unit ON press and hold the ON/OFF button for 4 seconds 2. When clr is shown in the main display the memory is cleared. 5
6 Measurement and Display Considerations The DO600 uses a polarographic sensor, which consumes oxygen at the sensing surface. This requires a constant movement of the sample across the membrane to maintain a constant dissolved oxygen level. It is recommended that the probe be moved in the sample as the measurement is made, or if in a laboratory environment, the sample be stirred using a stir plate. If the unit appears to be locked (display frozen). It is possible that the Data Hold mode has been inadvertently accessed by a press of the MODE/HOLD button (HOLD will be displayed in the bottom left of the LCD). Simply press the MODE/HOLD button again or turn the meter off and back on again. If the meter does latch up and no button presses revive it, remove the batteries and restart. For maximum accuracy, allow sufficient time for the temperature of the probe to reach the temperature of the sample before taking a reading. This will be indicated by a stable temperature reading on the display. Maintenance Battery Replacement 1. Twist off the battery compartment cover. 2. Holding the battery housing in place with a finger, pull out the battery carrier using the two small tabs. 3. Replace the four (4) CR2032 batteries observing proper polarity. 4. Replace the battery carrier, reattach the battery compartment cap and tighten securely. You, as the end user, are legally bound (EU Battery ordinance) to return all used batteries, disposal in the household garbage is prohibited! You can hand over your used batteries / accumulators at collection points in your community or wherever batteries / accumulators are sold! Disposal: Follow the valid legal stipulations in respect of the disposal of the device at the end of its lifecycle Electrode Replacement 1. To remove the electrode, first turn the instrument OFF and then unscrew and remove the electrode retaining collar. (turn the collar counter-clockwise to remove). 2. Gently rock the electrode from side to side, pulling it away from the meter until it disconnects. 3. To attach an electrode, align the positioning keys on the electrode and the main body housing and then carefully push the electrode into the meter socket until it is fully seated. 4. Tighten the electrode retaining collar firmly enough to seal the electrode with the meter. 6
7 DO Bonded Membrane Cap replacement Important Note : Do not touch the membrane as skin oils will interfere with the oxygen permeability rate of the membrane. Use caution when replacing the bonded cap. 1. It is recommended that the electrode remain attached to the meter during this replacement process. 2. To remove the bonded cap from the electrode, unscrew the cap firmly and carefully counter-clockwise from the electrode (see diagram below). 3. Discard the used cap. Please Note: The installation of a bonded cap causes the membrane to be tightly streched over the cathode. ce a bonded cap is removed reinstallation is not possible as the membrane will no longer be properly streched over the cathode. 4. Rinse the old electrolyte solution from the Cathode and Anode before continuing. 5. Use the supplied Polishing Strips to clean, polish, shine, and/or remove scratches from the cathode. Be sure to moisten the cloth before polishing the cathode. Do not over-polish the sensitive gold cathode. 6. Set the new replacement bonded cap on a flat surface. Leave the cap in this position throughout the replacement process. 7. Fill the bonded cap with the electrolyte solution up to the bottom of the threads on the inside of the cap. 8. Tap the side of the bonded cap to help jar free any trapped air bubbles from the electrolyte solution. 9. Keeping the cap in a fixed position on a flat surface, carefully insert the electrode into the new bonded cap by first dipping and removing the electrode several times from the cap. With each dip, push the electrode progressively deeper into the bonded cap. Finally, screw the electrode slowly onto the bonded cap (clockwise) until fully tightened. The dipping and removal technique minimizes the introduction of air bubbles into the electrolyte solution. Air bubbles in the electrolyte can compromise measurements. 10. During the tightening of the bonded cap, excess electrolyte solution will leak out, this is normal and desireable since it minimizes the introduction of air pockets. Clean off the excess electrolyte before use. Electrode BONDED CAP Anode Cathode Clockwise to tighten Counter-clockwise to loosen Bonded Cap Air Vents 7
8 Specifications Display Bargraph, Sensor Membrane Operating Temp. Range ATC Range Salinity Compensation Altitude compensation Measurement Storage Battery Power Low Battery Indication Auto Power Off Dimensions/Weight 2000 count, Dual function 3 ½ digit LCD with Display size: 24 mm x 20 mm Polarographic type Bonded membrane cap with threaded fitting 0 to 50 C (32 to 122 F) 0 to 50 C (32 to 122 F) 0 to 50 ppt in 1 ppt (part per thousand) increments 0 to 20,000 ft (in 1000 ft increments) 25 tagged (numbered) data sets with recall Four (4) CR2032 button batteries BAT appears on the LCD After 10 minutes of inactivity (APO override available) 36 x 173 x 41mm (1.4 x 6.8 x 1.6 ); 110g (3.8 oz) Measurement Range Resolution Accuracy % Saturation 0 to 200.0% 0.1% ±2.0% FS (full scale) Dissolved Oxygen 0 to mg/l 0.01 mg/l ±2% FS Concentration 0 to ppm 0.01 ppm ±2% FS Temperature 0 to 50 C 0.1 C ±1.0 C 32 to 122 F 0.1 F (0 to 99ºF); 1.0 F (>100 F) ±1.8 F 8
9 Appendices Troubleshooting Guide Symptom Possible Causes Action Unit will not power on -Batteries not in place -Dead batteries -Battery polarity incorrect -Replace Batteries -Replace Batteries -Reorient/Replace Batteries BAT indicator shown on -Batteries are weak -Replace Batteries display Unstable Readings Readings drift down -Insufficient electrolyte in probe (Air bubbles present when probe is inverted.) -Electrolyte is depleted -Insufficient stirring (the probe consumes oxygen at the measuring surface, requiring constant sample movement across membrane) -Replace electrolyte, and membrane cap assembly. -Move probe in sample or stir sample Slow Response -Dirty or damaged membrane -Replace electrolyte and membrane cap Electrode cannot be calibrated -Depleted electrolyte -Dirty or damaged membrane -Replace electrolyte and membrane cap Electrode cannot be calibrated after replacing the electrolyte and membrane cap -Dirty probe (Cathode is not a shiny gold color) -Clean cathode with cleaning paper Sample reading is frozen -Unit is in HOLD mode -Unit is locked -Release HOLD (momentarilly press Mode/Hold button) -Remove batteries, press ON/OFF button, replace batteries and restart 9
10 Operational Matrix for the Model DO600 Function / Resulting Action Power Status Mode Setting Required Button Press Sequence /Off Any Any Momentary press of the ON/OFF button Water Saturated Any Place Electrode in Calibration Cap Air Calibration Press & hold CAL/RECALL button for 2 seconds Zero Calibration Place Electrode in Zero Solution, wait for stability Any Press & hold CAL/RECALL button for 2 seconds Store Reading Any Momentary press of the MODE/HOLD button Hold Release Enter Memory Retrieval Scroll Stored Readings Exit Memory Retrieval Clear Stored Memory While In Hold Mode Any Memory Recall Memory Recall Any Measurement Mode Change Measurement Mode Any Enter Salinity Compensation Any Changing Salinity Compensation SAL Exit Salinity Compensation Enter Altitude Compensation SAL Any or SAL Changing Altitude Compensation Ald Exit Altitude Compensation Change Temperature Units Off Ald n/a (off mode) Override Autopower Off Any Default Reset Off n/a (off mode) Momentary press of the MODE/HOLD button Momentary press of the Cal button followed by a momentary press of the MODE/HOLD button (w/in 4 seconds) Momentary press of the MODE/HOLD button Momentary press of the CAL/RECALL Press and hold the ON/OFF button for 4 seconds Press and hold the MODE/HOLD button for at least two seconds (the modes will scroll until the button is released) Press and release the CAL/RECALL button twice (momentary) in succession (Displays SAL) Momentary press of the MODE/HOLD button (each button press increases the ratio by 1 ppt (part per thousand), the value cycles from 0 to 50) Press and release CAL/RECALL button for 2 seconds to enter Altitude Compensation, Or Press and release Cal Button one more time to enter measurement mode Press CAL/RECALL twice (momentary). Unit enters Salinity Mode. Press CAL/RECALL for 2 seconds to enter Altitude Compensation Mode. (Displays Ald) Momentary press of the MODE/HOLD button(each button-press increases altitude by 1,000ft, the value cycles from 0 to 20) Momentary press CAL/RECALL button to exit and save changes. Press and hold the CAL/RECALL button then momentarily press the ON/OFF button. Release the CAL/RECALL button after the "SELF CAL" lights Press CAL/RECALL button (momentary) then simultaneously press and hold the MODE/HOLD and ON/OFF buttons for for 2 seconds. Simultaneously press ON/OFF, CAL/RECALL and MODE/HOLD momentarily. dflt will be displayed. Comments Also works with probe removed (Cal at zero current) Stores and holds reading HOLD displayed If no data is stored in memory, End is displayed briefly, and then returns to last mode. clr is displayed. It is necessary to press the CAL/RECALL button to save changes. If the unit times out, no changes are saved. Unit times out in 5 seconds if no button is pressed, reverts to previous mode. It is necessary to press the CAL/RECALL button to save changes. If the unit times out, no changes are saved. 10
11 Re-order and Accessory Information Part Number DO600 DO605 DO603 EX010 EX050 DO610 CA895 Description ExStik II Dissolved Oxygen Meter Replacement Probe, ExStik II Dissolved Oxygen Meter Membrane Kit for DO600 Contains: 6 Membrane Caps, 15 ml Filling Solution, Polishing Paper Extension Cable 3 feet (1 Meter) & Probe Weight Extension Cable 16 feet (5 Meter) & Probe Weight ExStik II DO/pH/Conductivity Meter Kit Contains: EC500 ph/conductivity/salinity/tds ExStik II Meter, DO600 Dissolved Oxygen ExStik II Meter, Single use ph buffer pouches 4, 7, and 10pH, Sample Cups with Cap, Weighted Base for Sample Cups, and Batteries, all packed in a Carrying Case Small Soft Vinyl Pouch with Belt Loop for ExStik and ExStik II Copyright 2010 Extech Instruments Corporation. All rights reserved including the right of reproduction in whole or in part in any form. 11
ExStik DO600 USER GUIDE. Dissolved Oxygen Meter. 99 Washington Street Melrose, MA Phone Toll Free
USER GUIDE ExStik DO600 Dissolved Oxygen Meter 99 Washington Street Melrose, MA 02176 Phone 781-665-1400 Toll Free 1-800-517-8431 Visit us at www.testequipmentdepot.com II RECALL Dissolved Oxygen DO600
More informationTracer DO PockeTester TM Code 1761
Tracer DO PockeTester TM Code 1761 FILL - Before first use POLARIZE - Weekly CALIBRATE - Daily See Pages 9-12 Water Testing Leader Since 1919! WARNING! This set contains chemicals that may be harmful if
More informationUser's Guide. Pinless Moisture Meter. Model MO257
User's Guide Pinless Moisture Meter Model MO257 Introduction Congratulations on your purchase of the Extech MO257 Pinless Moisture Meter. The pinless moisture sensor monitors the moisture in wood and other
More informationUSER GUIDE Heat Index Psychrometer
USER GUIDE Heat Index Psychrometer Model RH25 Introduction Thank you for selecting the Extech Instruments Model RH25 Heat Index Psychrometer. The RH25 measures Temperature and Relative Humidity (using
More informationUSER MANUAL Digital CO Monitor Model CO30
USER MANUAL Digital CO Monitor Model CO30 Additional User Manual Translations available at www.extech.com Introduction Thank you for selecting the Extech Instruments Model CO30. The CO30 is a 3 in one
More informationPinless Moisture/Humidity Meter with Memory + IR Thermometer
User's Guide Extech MO295 Pinless Moisture Psychrometer w/ IR Thermometer Extech MO295-NISTL Pinless Moisture Psychrometer w/ IR Thermometer Pinless Moisture/Humidity Meter with Memory + IR Thermometer
More informationHydroMaster USER S GUIDE HM-500
HydroMaster USER S GUIDE HM-500 TABLE OF CONTENTS 1. INTRODUCTION... 2 A. Overview... 2 B. What s Included... 2 C. Housing Description... 2 D. Specification... 3 E. LCD Display... 4 F. Switch and Keypad
More informationWet Bulb Thermo-Hygrometer Datalogger
USER GUIDE Wet Bulb Thermo-Hygrometer Datalogger Plus Dew Point Temperature Model WB200 Introduction Thank you for selecting the Extech Instruments WB200 Thermo-Hygrometer Datalogger with Dew Point and
More informationDual Laser InfraRed (IR) Thermometer
User Manual Dual Laser InfraRed (IR) Thermometer MODEL 42512 Introduction Congratulations on your purchase of the Model 42512 IR Thermometer. This Infrared thermometer measures and displays non-contact
More information4-in-1 Humidity, Temperature Airflow and Light Meter
User's Guide 4-in-1 Humidity, Temperature Airflow and Light Meter Model 45170 Introduction Congratulations on your purchase of Extech s Model 45170 4-in-1 Humidity, Temperature, Airflow and Light Meter.
More informationDissolved Oxygen Sensors
Instruction Sheet PN 51A-HxDO/rev.E July 2005 Models Hx438 and Gx448 Dissolved Oxygen Sensors For additional information, please refer to the Instruction Manuals CD shipped with this product, or visit
More informationPinless Moisture/Humidity Meter with Memory + IR Thermometer
User's Guide Pinless Moisture/Humidity Meter with Memory + IR Thermometer Model MO295 mbar GPP RH% 01 MEM STORE MO295 Introduction Congratulations on your purchase of the Extech MO295 Pinless Moisture
More informationQuick Start Guide LIQ-QSG-Hx438, Rev A June Rosemount Hx438. Amperometric Steam Sterilizable Dissolved Oxygen Sensors
Quick Start Guide LIQ-QSG-Hx438, Rev A June 2017 Rosemount Hx438 Amperometric Steam Sterilizable Dissolved Oxygen Sensors Safety Information WARNING! Do not exceed temperature and pressure limitations
More informationUSER GUIDE. Paperless Humidity/Temperature Chart Recorder. Model RH520A 21.2 C 13:
USER GUIDE Paperless Humidity/Temperature Chart Recorder Model RH520A 30 10 100 0 13:45 04-23-04 21.2 C 38 Introduction Congratulations on your purchase of the Extech RH520A Temperature + Humidity Chart
More informationTable of Contents 1. OVERVIEW SYSTEM LAYOUT SPECIFICATIONS FUNCTION... 11
Table of Contents 1. OVERVIEW... 3 2. SYSTEM LAYOUT... 4 3. SPECIFICATIONS... 8 3.1 SYSTEM COMPONENTS...9 3.2 PLC INPUTS AND OUTPUTS...9 3.3 FUNCTION KEYS...10 3.4 DEFAULT SET POINTS AND TIMERS...10 4.
More informationCarbon Monoxide Meter Model CO15. User Manual. Additional User Manual Translations available at
Carbon Monoxide Meter Model CO15 User Manual Additional User Manual Translations available at www.extech.com Introduction Thank you for selecting the Extech CO15 Carbon Monoxide Meter. The CO15 is a digital,
More informationUSER GUIDE. Formaldehyde (HCHO or CH 2 0) and Total Volatile Organic Compounds (TVOC) Tester. Model VFM200
USER GUIDE Formaldehyde (HCHO or CH 2 0) and Total Volatile Organic Compounds (TVOC) Tester Model VFM200 Introduction Thank you for selecting the Extech Instruments Model VFM200. The VFM200 measures HCHO
More informationUser's Guide. CO 2 Monitor. Model CO200
User's Guide CO 2 Monitor Model CO200 Introduction Congratulations on your purchase of this Model CO200 Carbon Dioxide Meter. This meter measures CO2 level, air temp., humidity, date and time. With visible
More informationCLEAN MIST SMART HUMIDIFIER TABLETOP & FLOOR STANDING WITH REMOTE CONTROL. Instruction Manual and Warranty Information
CLEAN MIST SMART HUMIDIFIER TABLETOP & FLOOR STANDING WITH REMOTE CONTROL Instruction Manual and Warranty Information IM0034A READ AND SAVE THESE INSTRUCTIONS Contents Safety Instructions... 1 Unpacking
More information1 4 DIN Dissolved Oxygen Controller
16. Warranty OAKTON warrants this controller to be free from significant deviations in material and workmanship for a period of one year from date of purchase. If repair or adjustment is necessary and
More informationToxiRAE II. PGM-1100 Series Personal Toxic Gas Monitor. User Manual
ToxiRAE II PGM-1100 Series Personal Toxic Gas Monitor User Manual 045-4003-000, Rev C May 2007 - READ BEFORE OPERATING - This manual must be carefully read by all individuals who have or will have the
More informationRK/ RK Carbon Monoxide Detector Operator s Manual
65-2496RK/65-2499RK Carbon Monoxide Detector Operator s Manual Part Number: 71-0156RK Revision: 0 Released: 2/16/11 www.rkiinstruments.com WARNING Read and understand this instruction manual before operating
More informationMitocell: Instructions for Use
Mitocell: Instructions for Use 1 Introduction The Mitocell (MT200) is designed for the measurement of the respiration rate of either 50 or 100µl sample volumes of mitochondria and cell suspensions. The
More informationProduct waste disposal - Protection of the environment:
Product waste disposal - Protection of the environment: In accordance with the provisions of the Waste Electrical and Electronic Equipment (WEEE - 2002/ 96/ EC) Directive, used electric and electronic
More informationIndoor/Outdoor Temperature Alert
User Manual Indoor/Outdoor Temperature Alert Model 4004A Additional User Manual Translations available at www.extech.com Introduction Congratulations on your purchase of the 4004A Indoor/Outdoor Temperature
More informationInstruments. for hydroponics & horticulture 2016
Instruments for hydroponics & 2016 contents& spotlight Products & Spotlight p4 p9 8000 & 8100 ph Meters 6500 Therma-Hygrometer 8100 Plus ph & Temperature Meter p5 Contents description page no. alarm therma-hygrometers
More informationHP727S. Single speed swimming pool heat pump controller Operation manual TABLE OF CONTENTS
HP727S Single speed swimming pool heat pump controller Operation manual TABLE OF CONTENTS 1. General Description 2. Specifications 3. Installation Instructions 4. Electrical Wiring 5. Instrument Wiring
More informationMiniCO, MiniH 2 S, MiniOX, MiniOX Remote, MiniCl 2. , and MiniClO 2. Responder Detectors Instruction Manual "! WARNING
MiniCO, MiniH 2 S, MiniOX, MiniOX Remote, MiniCl 2 TM, and MiniClO 2 TM Responder Detectors Instruction Manual "! WARNING THIS MANUAL MUST BE CAREFULLY READ BY ALL INDIVIDUALS WHO HAVE OR WILL HAVE THE
More informationUser Guide. Moisture Meter. Model MO230
User Guide Moisture Meter Model MO230 Introduction Congratulations on your purchase of the Extech MO230 Moisture Meter. The MO230 detects moisture in wood and building materials such as wall board, sheet
More informationCLEAN MIST DUAL TANK SMART HUMIDIFIER. Instruction Manual and Warranty Information TABLETOP & FLOOR STANDING WITH REMOTE CONTROL
CLEAN MIST DUAL TANK SMART HUMIDIFIER TABLETOP & FLOOR STANDING WITH REMOTE CONTROL Instruction Manual and Warranty Information IM0036B READ AND SAVE THESE INSTRUCTIONS Contents Safety Instructions...
More informationEL-USB-2-LCD+ High Accuracy Humidity, Temperature and Dew Point Data Logger with LCD
High Accuracy Humidity, Temperature and Dew Point Data Logger with LCD ORDERING INFORMATION Standard Data Logger (Data Logger, Software on CD, Battery) Replacement Battery 99 Washington Street Melrose,
More informationUser's Guide. Pinless Moisture/Humidity Meter with Memory + IR Thermometer. Model MO295
User's Guide Pinless Moisture/Humidity Meter with Memory + IR Thermometer Model MO295 Introduction Congratulations on your purchase of the Extech MO295 Pinless Moisture Meter with Patented Built-in IR
More informationCT-7 Series Toxic Gas Transmitter Operator s Manual
65-2341 CT-7 Series Toxic Gas Transmitter Operator s Manual Part Number: 71-0424 Revision: P1 Released: 6/8/17 RKI Instruments, Inc. www.rkiinstruments.com WARNING Read and understand this instruction
More informationEVac II Programmable Digital Vacuum Gauge
EVac II Programmable Digital Vacuum Gauge Thank you for your purchase of the YELLOW JACKET evac II Digital Vacuum Gauge. The evac II is the most accurate and precise vacuum gauge available today with patented
More informationModel VFM200. User Manual. Formaldehyde (HCHO or CH 2 0) and Total Volatile Organic Compounds (TVOC) Tester
User Manual Formaldehyde (HCHO or CH 2 0) and Total Volatile Organic Compounds (TVOC) Tester Model VFM200 Additional User Manual Translations available at www.extech.com Introduction Thank you for selecting
More informationRK-02 Multi Point Detector Operator s Manual
65-2485RK-02 Multi Point Detector Operator s Manual Part Number: 71-0237RK Revision: A Released: 11/26/14 RKI Instruments, Inc. www.rkiinstruments.com WARNING Read and understand this instruction manual
More informationRK/ RK Oxygen Detector Operator s Manual
65-2494RK/65-2497RK Oxygen Detector Operator s Manual Part Number: 71-0179RK Revision: 0 Released: 2/16/11 www.rkiinstruments.com WARNING Read and understand this instruction manual before operating detector.
More informationDL424/425 DirectLine Sensor Module for Dissolved Oxygen Probes Series DL5000 Specifications
DL424/425 DirectLine Sensor Module for Dissolved Oxygen Probes Series DL5000 Specifications 70-82-03-48 January 2003 Overview The DirectLine DL424/425 Sensor Modules are part of a family of products developed
More informationUser Guide. ROSS Process Combination ph Electrode
User Guide ROSS Process Combination ph Electrode ROSS and the COIL trade dress are trademarks of Thermo Fisher Scientific Inc. AQUAfast, Cahn, ionplus, KNIpHE, No Cal, ORION, perphect, PerpHecT, PerpHecTion,
More informationToxiRAE II. PGM-1100 Series Personal Toxic Gas Monitor. User Manual
ToxiRAE II PGM-1100 Series Personal Toxic Gas Monitor User Manual 045-4003-000, Revision B, March 2005 - READ BEFORE OPERATING - This manual must be carefully read by all individuals who have or will have
More informationRK-05 Carbon Monoxide Detector Operator s Manual
65-2433RK-05 Carbon Monoxide Detector Operator s Manual Part Number: 71-0189RK Revision: 0 Released: 5/17/11 RKI Instruments, Inc. www.rkiinstruments.com WARNING Read and understand this instruction manual
More informationDigital Salt / TDS Meter. 390a. The Value Leader TM
Digital Salt / TDS Meter 390a The Value Leader TM www.tpi-thevalueleader.com Contents Before Use... 1 Description... 1 Applications... 1 Precautions... 2 Overview... 3 Functions... 4 LCD Symbols... 5 Specifications...
More informationPortable Oxygen Monitor OX-07. (Type A) Operating Manual
PT0E-0863 Portable Oxygen Monitor OX-07 (Type A) Operating Manual Request for the Customers Read and understand this operating manual before using this gas monitor. Use it in accordance with this operating
More informationUSB Multi Function Dataloggers. RHT30 Humidity/Temperature Datalogger. TH30 Dual Temperature Datalogger
USER MANUAL USB Multi Function Dataloggers RHT30 Humidity/Temperature Datalogger TH30 Dual Temperature Datalogger Additional User Manual Translations available at www.extech.com Introduction Thank you
More informationRK Carbon Monoxide Transmitter Operator s Manual
65-2335RK Carbon Monoxide Transmitter Operator s Manual Part Number: 71-0177RK Revision: 0 Released: 4/12/11 RKI Instruments, Inc. www.rkiinstruments.com WARNING Read and understand this instruction manual
More informationPortable Oxygen Monitor OX-07. (Type B) <No Gas alarm type> Operating Manual
PT0E-0922 Portable Oxygen Monitor OX-07 (Type B) Operating Manual Request for the Customers Read and understand this operating manual before using this gas monitor. Use it in accordance
More informationMODEL OX-07 Type A INSTRUCTION MANUAL FOR RIKEN PORTABLE OXYGEN MONITOR PT0E-0860
INSTRUCTION MANUAL FOR RIKEN PORTABLE OXYGEN MONITOR MODEL OX-07 Type A Safety Precautions Read and understand the instructions in this manual before operating this detector. Keep manual accessible all
More informationModel R9400. Instruction Manual. CO Meter with Temperature. wwwreedinstruments. com
Model R9400 CO Meter with Temperature Instruction Manual com Table of Contents Safety... 3 Features... 3 Specifications... 4 Instrument Description... 5 Operating Instructions...6-7 Selecting Temperature
More informationCarbon Monoxide Transmitter
Introduction The CO Transmitter uses an electrochemical sensor to monitor the carbon monoxide level and outputs a field-selectable 4-20 ma or voltage signal. The voltage signal may also be set to 0-5 or
More informationCLEAN MIST SMART HUMIDIFIER. Instruction Manual and Warranty Information TABLETOP & FLOOR STANDING WITH REMOTE CONTROL & MOOD LIGHT
CLEAN MIST SMART HUMIDIFIER TABLETOP & FLOOR STANDING WITH REMOTE CONTROL & MOOD LIGHT Instruction Manual and Warranty Information IM0041B READ AND SAVE THESE INSTRUCTIONS Contents Safety Instructions...
More informationRK Multi Point Detector Operator s Manual
65-2480RK Multi Point Detector Operator s Manual Part Number: 71-0198RK Revision: C Released: 11/26/14 RKI Instruments, Inc. www.rkiinstruments.com WARNING Read and understand this instruction manual before
More informationMini InfraRed (IR) Thermometer with Type K Input and Laser Pointer
USER MANUAL Mini InfraRed (IR) Thermometer with Type K Input and Laser Pointer MODEL IR267 Introduction Thank you for selecting the Extech Model IR267 Mini IR Thermometer. The Model IR267 IR thermometer
More informationSENSIT HXG-2d. SENSIT TECHNOLOGIES 851 Transport Drive Valparaiso, IN Phone: (219) Fax: (219)
WARRANTY AND REPAIR POLICY Your SENSIT HXG-2d instrument is warranted to be free from defects in materials and workmanship for a period of two years after purchase (excluding sensor, calibration and batteries).
More informationPAC-2750 ELECTRIC COOLING FAN CONTROLLER
PAC-2750 ELECTRIC COOLING FAN CONTROLLER IMPORTANT NOTE: The +12V for the controller should NOT be taken from the same circuit as the Fan Power 12V as this can cause the fan to cycle on and off. Required
More informationOPERATING AND MAINTENANCE MANUAL
HYDROFILL Hydronic water treatment filling units Copyright 2016 Caleffi OPERATING AND MAINTENANCE MANUAL NA10439 www.caleffi.com NA5709 series Function HYDROFILL is a water treatment fi lling unit that
More informationCLEAN MIST DUAL TANK SMART HUMIDIFIER. Instruction Manual and Warranty Information READ AND SAVE THESE INSTRUCTIONS IM0036A
CLEAN MIST DUAL TANK SMART HUMIDIFIER Tabletop & Floor Standing Instruction Manual and Warranty Information IM0036A READ AND SAVE THESE INSTRUCTIONS Contents Safety Instructions... 1 Unpacking / Specifications...
More informationRK CO 2 Transmitter Operator s Manual
65-2397RK CO 2 Transmitter Operator s Manual Part Number: 71-0185RK Revision: B Released: 7/18/14 RKI Instruments, Inc. www.rkiinstruments.com WARNING Read and understand this instruction manual before
More informationUSER MANUAL USB Multi-Function Datalogger Model RHT35
USER MANUAL USB Multi-Function Datalogger Model RHT35 Additional User Manual Translations available at www.extech.com Introduction Thank you for selecting the Extech multi-function, easy-to-use, portable
More informationHIn3550 Magnetic Field Monitor User's Manual
HIn3550 Magnetic Field Monitor User's Manual Copyright 1993 by Holaday Industries, Inc. Manual #600053 10/97 $12.50 Revision Record Manual #600053 HIn3550 Magnetic Field Monitor Revision Description Date
More informationSENSIT HXG-2d Combustible Gas Detector
INSTRUCTION MANUAL SENSIT HXG-2d Combustible Gas Detector Read and understand instructions before use. 710183 UL 913 Intrinsically Safe for Use in Class I, Groups C and D, T3 Hazardous Locations For use
More informationEL-USB-1-LCD Temperature Data Logger with LCD
99 Washington Street Melrose, MA 02176 Phone 781-665-1400 Toll Free 1-800-517-8431 EL-USB-1-LCD Temperature Data Logger with LCD Visit us at www.testequipmentdepot.com ORDERING INFORMATION Standard Data
More informationIMPORTANT: DO NOT DO NOT DO NOT DO NOT DO NOT DO NOT DO NOT DO NOT DO NOT DO NOT
Model: LV600HH Hybrid Ultrasonic Humidifier Questions or Concerns? Please contact us Mon-Fri 9:00AM-5:00PM PST at (888)726-8520 or email support@levoit.com Thank You. Thank you for purchasing the Hybrid
More informationModel: LD5 Dual Mode Refrigerant Gas Leak Detector. Operating Instructions
99 Washington Street Melrose, MA 02176 Phone 781-665-1400 Toll Free 1-800-517-8431 Visit us at www.testequipmentdepot.com Operating Instructions Model: LD5 Dual Mode Refrigerant Gas Leak Detector PAGE
More informationtesto 316-EX gas leak detector Instruction manual
testo 316-EX gas leak detector Instruction manual 2 1 Safety and the environment 1 Safety and the environment 1.1. About this document Use > Please read this documentation through carefully and familiarize
More informationORP (mv) Controller Model: ORP-XP2. UP DOWN ENTER Time & Date Main Menu Alarm Reset
Instruction Manual ORP (mv) Controller Model: ORP-XP2 Power Control Alarm Comms UP DOWN ENTER Time & Date Main Menu Alarm Reset Supplied by: Convergent Water Controls Pty Ltd 2/4 Huntley Street, PO Box
More informationCLEAN MIST SMART HUMIDIFIER Instruction Manual and Warranty Information IM0031B READ AND SAVE THESE INSTRUCTIONS
CLEAN MIST SMART HUMIDIFIER Instruction Manual and Warranty Information IM0031B READ AND SAVE THESE INSTRUCTIONS Contents Safety Instructions... 1 Unpacking / Specifications... 2 Parts & Contents... 3
More informationRK Hydrogen Sulfide Transmitter Operator s Manual
65-2331RK Hydrogen Sulfide Transmitter Operator s Manual Part Number: 71-0176RK Revision: B Released: 11/26/14 RKI Instruments, Inc. www.rkiinstruments.com WARNING Read and understand this instruction
More informationModel: LD7 Dual Mode Refrigerant Gas Leak Detector. Operating Instructions
99 Washington Street Melrose, MA 02176 Phone 781-665-1400 Toll Free 1-800-517-8431 Visit us at www.testequipmentdepot.com Operating Instructions Model: LD7 Dual Mode Refrigerant Gas Leak Detector PAGE
More informationTIF9055 Programmable. Owner s Manual Manual del Propietario Manuel du propriétaire Benutzerhandbuch Manuale del proprietario
TIF9055 Programmable Refrigerant Meter Owner s Manual Manual del Propietario Manuel du propriétaire Benutzerhandbuch Manuale del proprietario TABLE OF CONTENTS 1 General Information 2 Features 3 Controls
More informationGasAlert. Introduction. WWarning. Table 1. GasAlert Models. Gas Monitored
Introduction Table 1. GasAlert Models WWarning To ensure your personal safety, read Safety Information before you use the detector. The GasAlert gas detector ( the detector ) warns of hazardous gas at
More informationMultiFix Central unit
MultiFix Manual MultiFix Central unit 2015-12- 01 C85C5EN16 Contents CONTENTS... 2 GENERAL INFORMATION... 4 SAFETY INFORMATION... 4 DESCRIPTION OF OPERATION... 4 FUNCTIONS FOR MEASUREMENT... 4 UNPACKING...
More informationSmart Temp. Model
Smart Temp Model 42-160 SINGLE STAGE PROGRAMMABLE THERMOSTAT 1 Heat / 1 Cool Single Stage Thermostat. 5+2 Programmable, Compatible with Gas Heat & Heat Pump System Installation and Operation Manual SPECIFICATIONS:--------------------------------------------------------------------------------
More informationMODEL A-316 CARBON MONOXIDE (CO) MONITOR AND ALARM FOR COMPRESSED AIR TESTING
MODEL A-316 CARBON MONOXIDE (CO) MONITOR AND ALARM FOR COMPRESSED AIR TESTING FOR OPERATION FROM 115 AC POWER Andersen Medical Gas 12 Place Lafitte Madisonville, LA 70447 http://www.themedicalgas.com 1-866-288-3783
More informationDENVER CRL-310 ENGLISH FUNCTION AND CONTROLS
DENVER CRL-310 ENGLISH FUNCTION AND CONTROLS 1. LAMP SHADE 2. DISPLAY 3. LIGHT ON-OFF 4. TO SET THE LIGHT INTENSITY LOW 5. TO SET THE LIGHT INTENSITY HIGH 6. MOOD LIGHT ON OFF / MOOD LIGHT SELECT 7. TIME
More informationIntroduction... 3 Setup & Suggestions... 4 Basic Use... 4 Setting Time... 4 Setting Temperature... 5 Setting Height / Pressure...
Table of of Contents Contents... 2 Introduction... 3 Setup & Suggestions... 4 Basic Use... 4 Setting Time... 4 Setting Temperature... 5 Setting Height / Pressure... 6 Aligning the pedestal... 6 Guidelines
More informationFor Quick Set-Up go to Page 14
Talking Thermostat Model VT3000 Guide SmartWay Solutions, Inc. US Patent 6,608,560 & 7,62,253 For Quick Set-Up go to Page 4 Model VT3000, a universal thermostat for use on most Gas or Electric, Conventional
More informationR9900. Model. Instruction Manual. Indoor Air Quality Meter. reedinstruments. www. com
Model R9900 Indoor Air Quality Meter Instruction Manual reedinstruments com Table of Contents Features... 3 Specifications...3-4 Instrument Description...4-5 Operating Instructions...5-8 Data Hold... 5
More informationII 2 G. SENSIT HXG-2d. Ex ib IIB T3 IP20. Suitable for combustible gases such as Methane, Butane, Propane and Natural Gas MADE IN USA
SENSIT HXG-2d Combustible Gas Detector INSTRUCTION MANUAL Read and understand Instructions before use. PENDING II 2 G Ex ib IIB T3 IP20 PENDING (USA) Class 1, Division 1, Groups C and D, T3 Suitable for
More informationUser's Guide. Pinless Moisture/Humidity Meter + IR. Model MO290
User's Guide Pinless Moisture/Humidity Meter + IR Model MO290 Introduction Congratulations on your purchase of the Extech MO290 Pinless Moisture Meter with Patented Built-in IR Thermometer. Monitor moisture
More informationCLEAN MIST SMART HUMIDIFIER Instruction Manual and Warranty Information IM0002E READ AND SAVE THESE INSTRUCTIONS
CLEAN MIST SMART HUMIDIFIER Instruction Manual and Warranty Information IM0002E READ AND SAVE THESE INSTRUCTIONS Contents Safety Instructions... 1 Unpacking / Specifications... 2 Parts & Contents... 3
More informationJENCO INSTRUMENTS, INC. JENCO ELECTRONICS, LTD ARJONS DR., SUITE C P.O. BOX LINKOU-117
OPERATION MANUAL JENCO MODEL 6173 MICROCOMPUTER BASED ph/mv/temperature BENCH METER JENCO INSTRUMENTS, INC. JENCO ELECTRONICS, LTD. 7968 ARJONS DR., SUITE C P.O. BOX LINKOU-117 SAN DIEGO, CA 92126 TAIPEI
More information9-IN-1 THERMO-HYGROMETER/ MOISTURE METER USER S MANUAL
9-IN-1 THERMO-HYGROMETER/ MOISTURE METER USER S MANUAL RHMG650 99 Washington Street Melrose, MA 02176 Phone 781-665-1400 Toll Free 1-800-517-8431 Visit us at www.testequipmentdepot.com Please read this
More informationInstallation Instructions EFS Hand Washing Station
Installation Instructions EFS Hand Washing Station Both water and soap are sequenced and dispensed from outlet. Override button allows for non potable, water-only dispensing. Lighted icons indicate the
More informationMACHINE FROZEN CONCOCTION. Les meilleures margaritas sont originaires de Margaritaville
The Le Na Na vigateur vigator MACHINE FROZEN CONCOCTION MC Les meilleures margaritas sont originaires de Margaritaville modèle model dm dm1000-33 1000-33 Notice User d emploi Manual ImpOrtaNt SafEGuardS
More informationTHERMAPHASE INSTALLATION AND OPERATING INSTRUCTIONS
Page 1 of 10 THERMAPHASE INSTALLATION AND OPERATING INSTRUCTIONS Purpose of Manual The purpose of this manual is to provide operating, servicing and repair instructions for the Summit standard models ThermaPhase
More informationWSK300 Multifunction Wall Control
WSK300 Multifunction Installation & Operating Instructions WARNING Hearth & Home Technologies disclaims any responsibility for, and the warranty will be voided by, the following actions: Installation and
More informationUsing the QRAE Plus personal multigas monitor
Using the QRAE Plus personal multigas monitor Firmware v 1.10 QRAE Plus The Hazardous Environment Detection Company QRAE Plus features Turning on the QRAE Plus Recommended Daily Start-up Procedure User
More informationInstruction Manual for the Revolutionary Science RS-PB-200 Dual Poly Pro Bath
Instruction Manual for the Revolutionary Science RS-PB-200 Dual Poly Pro Bath REVOLUTIONARY SCIENC E Manufacturer of Precision Laboratory Equipment Table of Contents Introduction 2 Recommended Safeguards
More informationProfessional Wireless Rain Guage with 4" LCD
XC0430 User Manual (Non-RC D-M 917MHz) Size:A5 Professional Wireless Rain Guage with 4" LCD CONTENTS INTRODUCTION...1 PRODUCT FEATURES...1 OVERVIEW...2 LCD DISPLAY...3 INSTALLATION OF WIRELESS SENSOR...4
More informationHI COD REACTOR and Test Tube Heater 2008 Series
Instruction Manual HI 839800 COD REACTOR and Test Tube Heater 2008 Series www.hannainst.com This Instrument is in Compliance with the CE Directives 1 Dear Customer, Thank you for choosing a Hanna product.
More informationSierra Model 951 Digital Flo-Box. Instruction Manual Part Number IM-951 Revision A 09-05
Sierra Model 951 Digital Flo-Box Instruction Manual Part Number IM-951 Revision A 09-05 5 Harris Court, Building L Monterey, CA 93940 (831) 373-0200 (800) 866-0200 Fax (831) 373-4402 www.sierrainstruments.com
More informationGasWatch 2 Operator s Manual Part Number: RK Revision: E Released: 2/13/06
GasWatch 2 Operator s Manual Part Number: 71-0065RK Revision: E Released: 2/13/06 www.rkiinstruments.com Warranty RKI Instruments, Inc., warrants the GasWatch 2 sold by us to be free from defects in materials,
More informationPackage Contents. Dry Block Heater Power Cord Instruction manual Warranty Card. Serial Number: Date of Purchase: Supplier: Table of Contents
- English... 1 Instruction Manual Analog, Dry Block Heater, 1 Block, HB1AL Analog, Dry Block Heater, 2 Block, HB2AL Analog, Dry Block Heater, 4 Block, HB4AL Analog, Dry Block Heater, 6 Block, HB6AL Digital,
More informationMaytag Services Training Bulletin
Maytag Services Training Bulletin Product: New Electronic Control Date: August 1, 2005 IntelliDial Electronic Laundry Controls A new line of electronic controls, IntelliDial, hits the Sales Floor in August.
More informationMODEL ORP/pH Digital Controller
MODEL 554000 ORP/pH Digital Controller Operating Manual Rola-Chem Digital Controller PN 554102 6/01/2012 Page: 1 of 20 QUICK START REFERENCE Use this section for reference - please read all safety instructions
More informationEL-USB-CO300 Carbon Monoxide (CO) Data Logger with USB Interface
Carbon Monoxide (CO) Data Logger with USB Interface ORDERING INFORMATION Standard Data Logger (Data Logger, Software on CD, Battery) Replacement Battery EL-USB-CO300 BAT 3V6 1/2AA FEATURES 0 to 300 ppm
More informationInstruction Manual and Warranty Information
CLEAN MIST TOP-FILL SENSATOUCH HUMIDIFIER WITH REMOTE CONTROL & AROMA TRAY TABLETOP & FLOOR STANDING Instruction Manual and Warranty Information IM0057A READ AND SAVE THESE INSTRUCTIONS Contents Safety
More informationSENSIT HXG-2d Combustible Gas Detector INSTRUCTION MANUAL Read and understand Instructions before use. PENDING Ex. II3G Ex ic llb T3 IP20
SENSIT HXG-2d Combustible Gas Detector INSTRUCTION MANUAL Read and understand Instructions before use. PENDING Ex II3G Ex ic llb T3 IP20 PENDING (USA) Class 1, Zone 2, AEx nl llb T3 PENDING (Canada) Class
More informationCOMPASS S3 S2 CALIBRATION
FEATURES CP 600 is a digit watch for general outdoor sport timing featuring an electronic compass that for easy positioning. It equips with daily alarm that signals the designated time. The watch is provided
More informationULTRASONIC DIGITAL HUMIDIFIER Instruction Manual and Warranty Information IM0002A READ AND SAVE THESE INSTRUCTIONS
ULTRASONIC DIGITAL HUMIDIFIER Instruction Manual and Warranty Information IM0002A READ AND SAVE THESE INSTRUCTIONS Contents Safety Instructions... 1 Unpacking / Specifications... 2 Parts & Contents...
More information