FLV 40 UV Flame Detector
|
|
- Coral Lee
- 5 years ago
- Views:
Transcription
1 FLV 40 UV Flame Detector TECHNICAL INSTRUCTIONS FOR INSTALLATION, SETUP ANDMAINTENANCE EDS srl - V. Cà Nova Zampieri S.G.Lupatoto - Verona - Italy - tel fax Mail: eds@eds.eu - Web: 1
2 FLV 40 UV FLAME DETECTOR TECHNICAL INSTRUCTIONS The FLV40 Flame Detector is able to detect a flame produced inside its viewing range in a few seconds. Its installation is very simple and can be done in a few minutes. To obtain the best results we suggest to read the instructions below entirely and to follow the procedures described carefully. 1 - The FLV40 reacts with great sensitivity to Ultraviolet radiations emitted by an adequately powerful source located in its viewing range. 2 - The device must be installed on a wall or on the ceiling. Normally, to surveil goods located on the floor, the ceiling installation is suggested. 3 - The installation height is relative to the area to be protected considering that the detector's viewing range is about 60 and that the maximum distance for flame detection (for a petrol generated flame with a target of 20 x 20 x 5 cm square steel tray) it's 20 m. The fig. 3 e 4 diagrams indicate the diameter and the covered area related to the installation height. 4 - Take the front cover off (where the aluminium cone with the sensor is located) taking off the four screws located in the cover's corners. Be careful in handling the cover with the sensor mounted as a shock could damage it permanently. 5 - Make a hole, with the desired diameter, on the bottom of the plastic box and fix the cable gland tightly in order to obtain the best possible grade of protection against dust and dirt that are dangerous for the inside electronics on a long period of time done as outlined in fig select the power supply voltage by positioning the JP2 jumper in as follows: position 1-2 = supply voltage 24 V dc position 2-3 =supply voltage 12 V dc 9 - select the output relay working mode by positioning the JP1 jumper as follows: position 1-2 = normally not powered position 2-3 = normally powered 10 - adjust the alarm delay ( between 5 and 15 seconds) to the desiterd valur turning the TR1 trimmer 11 - Be careful when the circuit is powered. In fact an high voltage is generated on some parts and so the connecting and maintenance operations must be carried out with the device unpowered After the installing and adjusting operations are over a working test can be done (if the environment conditions permit it). In order to do this test, after powering the device, it is necessary to produce a flame with gasoline on a 20x20x5 cm square steel tray positioned at the extremity of the maximum area that the detector can cover. After the selected alarm delay time an alarm output should be produced. This test must be carried out carefully on high surveillance. 6 - Mount the box on the ceiling as outlined in the enclosed diagram (fig.1-2) 7 - Insert the connection cable inside the box and connect it to the terminal board located on the circuit board inside the cover. The connections must be 2
3 JP COM + _ TR1 JP NO NC - + RELAY SUPPLY VOLTAGE fig. 1 fig. 2 Installation Example 3
4 USAGE WARNINGS The UV sensor contained in the FLV40 flame detector can be damaged if exposed to high vibrations or shocks. In particular the glass bulb and the electrodes can beaffected by deformations. This fact can cause a serious loss of performance, faulty functioning and even permanently damage the device. All the UV sensor have been tested for vibrations and shocks as follows: - vibrational test: from 0 to 500Hz/0.06" in conformity to MIL-STD-202F method 204D - shock test: 100G/11ms, sinusoidal in conformity to MIL-STD-202F method 213B A wrong usage can get the UV sensor to be exposed to levels of vibrations and shocks higher than those of these tests. For example an accidental fall can cause permanent damages to the UV sensor. So it is nesessary to handle the device with the maximum care. INSTALLATION WARNINGS The FLV40 detector can be influenced by ultraviolet radiations different from those produced by flames. In fact there are many different types of UV radiation sources. The list below shows several types of uv sources that can be commonly found in nature. - sun light (the ultraviolet radiation intensity varies with the seasons, day time and geographic position of the site) - sparks generated during arc welding (these sparks emit high intensity UV radiations) - electric sparks (like those generated by engines or train pantographs) - sterilization lamps (like mercury low-pressure lamps) - halogen lamps (like the lenticular reflector spotlights) - high colour rendering lamps like xenon lamps and metal vapours lamps Keep in mind, during the installing, that when the UV sensor detects the presence of ultraviolet radiation it becomes an UV source itself. So if more than one UV flame detectors are installed in the same room, it is better not to install the detectors facing each other (on two opposite sides for example) to avoid that the alarm signal of one detector is transmitted to the other one. So they don't have to look to each other.. WARNING The FLV40 detector has an high sensitivity and so it can reveal UV radiations generated by unwanted sources. To avoid this problem it is enough to eliminate any extraneous UV sources from the environment where the detector is installed. TECHNICAL DATA power supply: 12 or 24 V dc selectable power consumption: 14,5 ma not in alarm with the relay normally not 30 ma in alarm with the relay normally not 25,5mA not in alarm with the relay normally 15 ma in alarm with the relay normally power supply range: from 10,5V to 33 V maximum detection distance: 20m (referred to a hydrocarbon target flame 20x20 cm - height 20 cm) viewing angle: 60 protection against inversion of polarity adjustable alarm relay: from 5" to 15" with an internal trimmer output relay contacts: 0,5A/24Vcc-ca external alarm led polycarbonate box protection index: IP55 electromagnetic immunity: in conformity to EN ; EN ; IEC dimensions: 120x75x85 mm. 4
5 Height [m] Diameter [m] fig. 3 FLV 40 COVERED AREA FLV40 Detector Ceiling COVERED AREA Floor fig. 4 The figure above is about ceiling installation. 5
FLV45 FLV45A FLV45A-AL
Flame Detector IR + UV FLV45 FLV45A FLV45A-AL Technical Manual EDS - V. Ca' Nova Zampieri 6-37057 S. G. Lupatoto - VERONA - Tel. 0039045547529 - Fax. 00390458750065 - Email: eds@eds.eu - Web: www.eds.eu
More informationOptical Beam Smoke Detector RK90R - RK90RS
Optical Beam Smoke Detector RK90R - RK90RS TECHNICAL INFORMATION APPLICATIONS museums churches art galleries libraries hotels shops cinemas computer rooms control rooms storehouses, etc. The RK90R it's
More informationQRA4.U. Flame Detector. Siemens Building Technologies HVAC Products
7 711 Flame Detector QRA4.U Flame detector for use with burner controls from for the supervision of gas or oil flames. The QRA4.U and this Data Sheet are intended for use by OEMs which integrate the flame
More informationEDS - SPARK DETECTORS - GENERAL NOTES
1 EDS - SPARK DETECTORS - GENERAL NOTES The spark detectors are electronic devices suitable for the detection of sparks in the pipes or transport ducts of conbustible material of different nature (sawdust,
More informationUV Flame Supervision System
7 783 UV Flame Supervision System DETACTOGYR LFE50 Series 02 ISO 9001 The LFE50 is a self-checking UV flame supervision system designed for use with continuously operating burners or for burners running
More informationFlame Detection Jon Sarfas
Flame Detection Jon Sarfas Agenda Introduction Detection Principles FL4000H MSIR Flame Detector Flame Test Lamp Installation Best Practice Features & Benefits Applications Introduction Primary objectives:
More informationExplosion-proof ATEX Spark Detector SCL-01
Explosion-proof ATEX Spark Detector SCL-01 TECHNICAL MANUAL EDS srl - V. Ca' Nova Zampieri 6-37057 S. G. Lupatoto - VERONA - Tel. +39045547529 - Fax +390458750065 Email: eds@eds.eu - Web: www.eds.eu 1
More informationQRA2... QRA10... QRA53... QRA55... Flame Detectors. Siemens Building Technologies HVAC Products
7 712 ISO 9001 QRA10... QRA53..., QRA55... with clamp QRA2... with clamp Flame Detectors QRA2... QRA10... QRA53... QRA55... The flame detectors are designed for use with our burner controls, for the supervision
More informationFlame Safeguards LFE10. Building Technologies HVAC Products
7 71 Flame Safeguards LAE LFE Flame safeguards for burners with intermittent operation The LAE is used for the supervision and indication of oil flames The LFE is used for the supervision and indication
More informationFlame detector. The QRA4.U is for use with the following types of burner control:
7 711 Flame detector QRA4.U UV flame detector for use with burner controls from Siemens for the supervision of gas or oil flames. The QRA4.U and this Data Sheet are intended for use by OEMs which integrate
More informationQRA10... QRA53... QRA55...
7 712 QRA10... QRA53..., QRA55... with clamp QRA2... with clamp Flame Detectors QRA2... QRA10... QRA53... QRA55... The UV flame detectors are designed for use with Siemens burner controls, for the supervision
More informationFLAME SENSOR FS-2000E
FLAME SENSOR FS-2000E We appreciate your purchase of a TAKEX flame sensor. Please read this instruction manual carefully for correct and effective use. This sensor is designed to detect flames and to initiate
More informationLAE10 LFE10. Use. Series 02
ISO 00 Flame Safeguards 7 7 LAE L Series 02 Supplementary data sheets 772 and 773 Flame safeguards for burners with intermittent operation. For safety reasons - self-test of flame supervision circuit,
More informationFlame detector. The QRA4.U is for use with the following types of burner control:
7 711 Flame detector QRA4.U UV flame detector for use with burner controls from Siemens for the supervision of gas or oil flames. The QRA4.U and this Data Sheet are intended for use by OEMs which integrate
More informationC Installation and Operation Manual
(Issue 2.02, December 2005) CONTENTS I General... 1 II Features... 1 III Technical Specifications... 1 IV Structure and Operation Principle... 1 V Mounting and Wiring... 2 VI Testing... 3 VII Troubleshooting...
More informationFlame Safeguards LFE10. Building Technologies HVAC Products
7 71 Flame Safeguards LAE LFE Flame safeguards for burners with intermittent operation The LAE is used for the supervision and indication of oil flames The LFE is used for the supervision and indication
More informationUV Flame Detector. User's and Maintenance Manual TM20/20UB Rev E, August 2004
UV Flame Detector Model 20/20U, 20/20UB User's and Maintenance Manual TM20/20UB Rev E, August 2004 Factory Mutual Approved Class I Div. 1 Groups B, C, D Class II Div. 1 Groups E, F, G ATEX Approved Ex
More informationQRA10... QRA53... QRA55...
7 712 QRA7 with clamp QRA10... QRA53..., QRA55... with clamp QRA2... with clamp Flame Detectors QRA2... QRA10... QRA53... QRA55... QRA73 QRA75 The UV flame detectors are designed for use with Siemens burner
More informationFlame detector. Building Technologies Division Infrastructure & Cities Sector
7 711 Flame detector QRA4 UV flame detector for use with burner controls from Siemens for the supervision of gas or oil flames. The QRA4... and this Data Sheet are intended for use by OEMs which integrate
More informationTesting Emission Source ITES Operating Manual OM
San Jose CA 95112 Page 1 of 5 Testing Emission Source ITES Operating Manual 50017-001 OM San Jose CA 95112 Page 2 of 5 1. Purpose The Testing Emission Source ITES GSKF.676216.001 (hereinafter after referred
More informationFlame Detector User Manual
This document is FD User Manual/003/Issue 1 User Manual General Description The flame detector is designed for use where open flaming fires may be expected. It responds to the light emitted from flames
More informationModel DRD-AS Conventional Infrared Flame Detector User Manual Ver. 1.0
Model DRD-AS Conventional Infrared Flame Detector User Manual Ver. 1.0 Page 1 of 11 DRD-AS Flame Detector User Manual Table of Contents 1.1 Description... 3 1.2 Alarm Response Modes... 3 1.3 IR Detection
More informationIFD-E Flame Detector User Manual
IFD-E Flame Detector User Manual 2 Hochiki Europe (UK) Ltd General Description The flame detector is designed for use where open flaming fires may be expected. It responds to the light emitted from flames
More informationQRA10... QRA53... QRA55...
7 712 QRA7 with clamp QRA10... QRA53..., QRA55... with clamp QRA2... with clamp Flame Detectors QRA2... QRA10... QRA53... QRA55... QRA73 QRA75 The UV flame detectors are designed for use with Siemens burner
More informationLFE50. UV Flame Safeguard. Siemens Building Technologies HVAC Products DETACTOGYR. Series 02
7 783 ISO 9001 DETACTOGYR Flame Safeguard Series 02 The... together with the QRA50M / QRA51M form a self-checking flame supervision system (DETACTOGYR ) designed for use with continuously operating oil
More informationIFD-E Flame Detector User Manual
IFD-E Flame Detector User Manual 2 Hochiki Europe (UK) Ltd General Description The flame detector is designed for use where open flaming fires may be expected. It responds to the light emitted from flames
More informationSharpEye 20/20I. Triple IR (IR 3 ) Flame Detector. User's and Maintenance Manual
SharpEye 20/20I Triple IR (IR 3 ) Flame Detector User's and Maintenance Manual Doc. No. TM 20/20I, Rev. (4)-99 July 1999 Factory Mutual Approved Class I Div. 1 Groups B, C, D Class II Div. 1 Groups E,
More informationC Note! LGI16... Burner Controls. Building Technologies
7 786 Burner Controls LGI16... Burner controls For use on industrial furnaces For burners in continuous operation Without fan control and air pressure supervision Flame supervision - with QR53... / QR55,
More informationEVL-B - Zone 1, 2, 21, 22 - Replaces traditional discharge lamps more than 400W - Saves in energy, maintenance and installation
EVL-B Shock-resistant tempered glass - Zone 1, 2, 21, 22 - Replaces traditional discharge lamps more than 400W - Saves in energy, maintenance and installation costs - Suitable for GAS category IIC LED
More informationSafety. Operating instructions UV sensor UVS 10 DANGER WARNING. Contents CAUTION Edition Please read and keep in a safe place
8.. Edition 08.0 D GB F NL I E DK S N P GR TR CZ PL RUS H www.docuthek.com Operating instructions UV sensor UVS 0 Translation from the German 008 009 Elster GmbH Contents UV sensor UVS 0......................
More informationSAFEYE XENON 700. Hydrocarbons and ethylene detection. Heated optics. 10-year Warranty for the Xenon flash bulb. SIL 2 according to IEC 61508
Open-Path Gas Detection System SAFEYE XENON 700 Hydrocarbons and ethylene detection Heated optics 10-year Warranty for the Xenon flash bulb SIL 2 according to IEC 61508 Certifications The Fixed Gas Detection
More informationactive infrared 875 nm < 250 mw/m² motion & presence 157 in x 157 in (emitting spots**) 2 in/s to activate detection 250 ms 15-45
Please keep for further use Designed for color printing Other use of the device is outside the permitted purpose and can not be guaranteed by the manufacturer. The manufacturer cannot be held responsible
More informationIR FLAME DETECTOR RIV-601/F
IR FLAME DETECTOR EN 54-10 class 2 VdS approval G 205044 application manual CONTROL LOGIC rev. 4 DEC07 MAFE DEC07 IR FLAME DETECTORS SUMMARY Page general notions...3 description...4. Electrical and general
More informationUltra Fast UV/IR Flame Detector
Ultra Fast UV/IR Flame Detector Model 20/20F User and Maintenance Manual TM756100 Rev A, July 2005 ATEX Approved Ex II 2G EExd IIB + H2 T5 EExde IIB + H 2 T5 218 Little Falls Rd., Cedar Grove, NJ 07009
More informationTalentum Flame Detector User Guide
Talentum Flame Detector User Guide This user guide covers all FM Approved Talentum 16000 series flame detectors: - 16589 IR3 standard - 16591 UV/IR2 standard - 16519 IR3 Exd - 16549 IR3 Exd SS (Stainless
More informationModel 3300 Technical Support and Installation Manual
Model 3300 Technical Support and Installation Manual Manual # T15011 Document Revision: A1 1. OVERVIEW 1 2. BASIC OPERATION 1 2.1 General 1 2.2 Field-of-View 2 2.3 Range 2 2.4 Environment 2 2.5 Configuration
More information300W Low Profile Clean Room LED Light - LED Signal Light - C1D1 - C2D2 - ISO 14644/FS-209E Rated
300W Low Profile Clean Room LED Light - LED Signal Light - C1D1 - C2D2 - ISO 14644/FS-209E Rated Part #: HALD-48-2X150LED-V2-C-OXM Page: 1 Made in Texas The HALD-48-2X150LED-V2-C-OXM from Larson Electronics
More informationDräger Flame 2700 (Multi-IR) Flame Detection
Dräger Flame 2700 (Multi-IR) Flame Detection With its multichannel IR sensor the Dräger Flame 2700 detects hydrocarbon- and hydrogen-based fires. Thereby it offers a high reliability against false alarms.
More informationCCA-03EX. - Easy installation - Low energy consumption - New COB LED technology - Zone 1, 2, 21, 22. Directional LED spotlights
CCA-03EX - Easy installation - Low energy consumption - New COB LED technology - Zone 1, 2, 21, 22 Directional LED spotlights Body and lid in coated aluminium LED for proper operation monitoring 127 ED.2018
More informationSingle IR Flame Detector. User and Maintenance Manual TM 20/20R, Rev. A January 2005
Single IR Flame Detector Model 20/20R User and Maintenance Manual TM 20/20R, Rev. A January 2005 ATEX Approved Ex II 2G EExd IIB + H 2 T5 EExde IIB + H 2 T5 GasTech Australia Pty Ltd 24 Baretta Rd Wangara
More informationLFE50. UV Flame Safeguard. Building Technologies Division DETACTOGYR
7 783 DETACTOGYR Flame Safeguard The... together with the QRA50M / QRA51M form a self-checking flame supervision system (DETACTOGYR ) designed for use with continuously operating oil or gas burners or
More information3F Linda Inox 1x.. T8 HF ATEX II 3D T85 C IP65
3F Linda Inox 1x.. T8 HF ATEX II 3D T85 C IP65 Product Technical Sheet 18, 36 and 58W single-lamp versions ST.0914.I Summary Application field 3 Structural characteristics 4 Electrical characteristics
More informationRota-Sonde DC4000-L. Laser pointer for easy alignment. Remote control of the sensitivity
Scanning HOT METAL DETECTOR Rota-Sonde DC4000-L Two sensitivity ranges : 400 C and 230 C Laser pointer for easy alignment Remote control of the sensitivity Self-monitoring ISO 9001 Applications Benefits
More informationSystem 2000 System 2000 presence detector Comfort top unit. 1 Safety instructions. 2 Device components
pure white Order-No. : 0317 02 colour aluminium Order-No. : 0317 04 Operating instructions 1 Safety instructions Electrical equipment may only be installed and fitted by electrically skilled persons. Failure
More informationThis document is a preview generated by EVS
TECHNICAL SPECIFICATION ISO/TS 7240-29 First edition 2017-06 Fire detection and alarm systems Part 29: Video fire detectors Systèmes de détection et d alarme d incendie Partie 29: Titre manque Reference
More informationSafety. Operating instructions UV sensor UVS 5 DANGER. Contents WARNING CAUTION Elster GmbH Edition Please read and keep in a safe place
06 Elster GmbH Edition 0.6 Translation from the German 0556 D F NL I E DK S N P GR TR CZ PL RUS H www.docuthek.com Operating instructions UV sensor UVS 5 Cert. version 0.6 Contents UV sensor UVS 5... Contents...
More informationExplosion Proof Light - Base Stand Mount - 16 Inch Watt LED - Class I Div 1 C&D
Explosion Proof Light - Base Stand Mount - 16 Inch - 150 Watt LED - Class I Div 1 C&D Part #: EPL-16BS-1X150LED-100 Page: 1 Made in Texas The EPL-16BS-1X150LED-100 Explosion Proof LED Light from Larson
More informationExercise 1. Introduction to Sensors EXERCISE OBJECTIVE
Exercise 1 Introduction to Sensors EXERCISE OBJECTIVE When you have completed this exercise, you will be introduced to photoelectric, capacitive and inductive sensors; You will also be introduced to the
More informationA series of technical features make this gas detector extremely versatile, reliable, accurate, and safe.
Belonging to Made in Italy GS911K Gas Detector GS911K Using the catalytic sensor inside it, the GS911K detector detects the presence of explosive gas such as: Methane, LPG, with trip sensitivity calibrated
More informationDetector switch - Dual Tech
Page 1. Use.................................... 1 2. Technical characteristics................1 3. Dimensions............................ 2 4. Connection........................... 2 5. Installation...........................
More information150 Watt Explosion Proof LED Light - 5' Tall Base Stand Mount - 24 Inch Stand - Class I Div 1 C&D
150 Watt Explosion Proof LED Light - 5' Tall Base Stand Mount - 24 Inch Stand - Class I Div 1 C&D Part #: EPL-24BS-5FT-1X150LED-100 Page: 1 Made in Texas The EPL-24BS-5FT-1X150LED-100 Explosion Proof LED
More informationExcellence in Level Measurement
Technical Data Sheet No. Novaflo 2000 'Fail-Safe' Level Alarm System Excellence in Level Measurement Afriso Eurogauge Ltd Imberhorne Lane, East Grinstead West Sussex. RH19 1RF Tel: 01342 323641 Fax: 01342
More informationDesign Manual Installation Operation Maintenance
Design Manual Installation Operation Maintenance Model F120 Triple-Mode UV/IR Flame Detector 70053 23282 Mill Creek Drive, Suite 215 Laguna Hills, CA 92653 USA +1.949.583.1857 Phone +1.949.340.3343 Fax
More information100W Explosion Proof Ultraviolet Portable LED Fixture - 365NM - EXP Cord Caps - 150ft Cord
100W Explosion Proof Ultraviolet Portable LED Fixture - 365NM - EXP Cord Caps - 150ft Cord Part #: EPL-PM-100LED-UVA-150-EPP Page: 1 The EPL-PM-100LED-UVA-150-EPP from Larson Electronics is an Explosion
More informationWide Band Flame Detector KLC 20 for all kind of oil flames with intermittent burnerr operations
KLC 20 0 (formerly known as KLC 2002) CE0085BP0001 Technical Information Wide Band Flame Detector KLC 20 for all kind of oil flames with intermittent burnerr operations Short Description The wide band
More informationC1D1 Explosion Proof 50W LED Flood Light Fixture - Paint Spray Booth Approved - Adj Surface Mount
C1D1 Explosion Proof 50W LED Flood Light Fixture - Paint Spray Booth Approved - Adj Surface Mount Part #: EPL-LED-50W-RT-JB2 Page: 1 The Larson Electronics EPL-LED-50W-RT-JB2 Explosion Proof High Bay light
More informationQRA10... QRA53... QRA55...
7 712 QRA7 with clamp QRA10... QRA53..., QRA55... with clamp QRA2... with clamp Flame Detectors QRA2... QRA10... QRA53... QRA55... QRA73 QRA75 The UV flame detectors are designed for use with Siemens burner
More informationCCTV, HOW DOES IT WORK?
August 25, 2005 CCTV FLAME DETECTION Video flame detection is an attractive concept. We ve all heard the adage, seeing is believing. In short, we trust our eyes to deliver accurate information. New designs
More informationCCTV Model Flame Detector. User and Maintenance Manual TM , Rev. A January 2005
CCTV Model Flame Detector Model 20/20CTIN-CTIP User and Maintenance Manual TM 788100, Rev. A January 2005 ATEX Approved Ex II 2G EExd IIB + H 2 T5 EExde IIB + H 2 T5 UL Approved Class I, Groups C and D
More informationSERIES VAC Microprocessor-Based Intermittent Pilot Ignition Control FEATURES APPLICATIONS SPECIFICATIONS DESCRIPTION
R SERIES 35-703 120 VAC Microprocessor-Based Intermittent Pilot Ignition Control F-35-703 July 2016 FEATURES Safe start with DETECT-A-FLAME flame sensing technology Custom pre-purge and inter-purge timings
More informationModel 20/20MI Mini Triple IR (IR3) Flame Detector
Model 20/20MI Mini Triple IR (IR3) Flame Detector User Guide Document ref: TM 787100, Rev. (5), May 2017 8200 Market Blvd, Chanhassen, MN 55317, USA Phone: +1 (973) 239 8398 Fax: +1 (973) 239 7614 Website:
More information150W Explosion Proof High Bay LED Light Fixture - C1D1&2 - C2D1&2-17,500 Lumens - 60 Beam
150W Explosion Proof High Bay LED Light Fixture - C1D1&2 - C2D1&2-17,500 Lumens - 60 Beam Part #: EPLC2-HB-155W-LED-PND Page: 1 The Larson Electronics EPLC2-HB-155W-LED-PND Explosion Proof High Bay light
More informationLow Profile Clean Room 150W LED Light - 2x2 Lay-In Troffer C1D1 - C2D2 - ISO 14644/FS-209E
Low Profile Clean Room 150W LED Light - 2x2 Lay-In Troffer - 140 - C1D1 - C2D2 - ISO 14644/FS-209E Part #: HALD-24-1X150LED-V2-140DB Page: 1 Made in the USA The HALD-24-1X150LED-V2-140DB from Larson Electronics
More informationQRC1... Blue-flame Detectors. Siemens Building Technologies HVAC Products
7 716 QRC1... for frontal illumination Blue-flame Detectors QRC1... for lateral illumination QRC1... Blue-flame detectors for the supervision of ue- or yellow-burning oil or gas flames. Blue-flame detectors
More informationEU RO Mutual Recognition Technical Requirements
Adoption 1 April 2016 1. PRODUCT DESCRIPTION... 1 2. DESIGN EVALUATION... 2 3. PRODUCTION REQUIREMENTS... 6 4. MARKING REQUIREMENTS... 6 6. APPROVAL DATE AND REVISION NUMBER... 7 7. BACKGROUND INFORMATION
More informationGiordano clothing store
MEGAMAN 2 RETAIL LIGHTING Retail architecture and design encompasses a variety of requirements. The environment must deliver a corporate brand identity; it must draw attention to specific products whilst
More informationLED Product Catalogue
LED Product Catalogue Valid from 01 March 2014 LED = innovative light 1 Contents LED = innovative light...page 3 Save energy and costs with LED...Page 4 A new light will go off in your head... Page 5 LED
More information2015 /9C EN-00 OSRAM GmbH Marcel-Breuer-Str München Germany. LED module PL-LIN-HV-DC-G1. M see attached list
Manufacturer's Declaration of Conformity with International Standards OSRAM fi Document number: Manufacturer or representative: Address: Brand name or trade mark: Product type: Product designation: OSRAM
More informationDPB52. True RMS 3-Phase, Multifunction monitoring relay. Benefits. Description
DPB52 True RMS 3-Phase, Multifunction monitoring relay Description Benefits Measuring Voltage Range. Very wide input voltage range: from 125 to 624V ( 208V 40% to 480 + 30% ). Adjustable Voltage Ranges
More informationINFRARED IP55 HEATER INSTRUCTIONS FOR: MODEL:- QZWP45N 1. SAFETY INSTRUCTIONS
INSTRUCTIONS FOR: INFRARED IP55 HEATER MODEL:- QZWP45N Thank you for purchasing a Consort Claudgen product. Manufactured to a high standard this product will, if used according to these instructions and
More informationUV - flame detector dual fuel burners for intermittent burner operations
KLC 11 1(formerly known as KLC 1001) Technical information UV - flame detector KLC 11 for oil -, gas- and dual fuel burners for intermittent burner operations 0085 Description The KLC 11 is a compact UV
More informationDräger Flame 2500 (IR3) Flame Detection
Dräger Flame 2500 (IR3) Flame Detection With its triple IR sensor The Dräger Flame 2500 detects hydrocarbonbased fires even over greater distances. Moreover, it offers a high reliability against false
More informationPRODUCT INFORMATION. Uses tough, high quality PC diffuser, resistant to fracture and to ultraviolet light to limit discolouring.
Ø297mm Packing list in Ceiling Mount Lamp LEDS 96PCS Φ6 Wall plug 3x30 Screw Φ3 Sealing ring 4x12 Y type Stainless Screw Quantity 1X 4X 4X 3X 3X PRODUCT INFORMATION 98.5mm Ideal for energy saving this
More informationSANDOR QUAD/ESA. Double beam. POLITEC s.r.l. Installation And commissioning manual
SANDOR QUAD/ESA Double beam Installation And commissioning manual 1 POLITEC s.r.l. Index Main components list Pag. 3 Installation reccomendations Pag. 4 Mounting the bracket Pag. 5 Installation example
More informationLaser Collimated Beam Sensor
SERIES Laser Collimated Beam Sensor Class 1 Laser Beam Sensor Safe for Your Eyes Marked Conforming to EMC Directive (Excluding LA-C1) Safe Laser Beam This laser collimated beam sensor conforms to the Class
More informationC2D1/C1D2 Explosion Proof 50 Watt LED Light Fixture - Paint Spray Booth Approved - 6,250 Lumens
C2D1/C1D2 Explosion Proof 50 Watt LED Light Fixture - Paint Spray Booth Approved - 6,250 Lumens Part #: EPLC2-HB-50LED-RT Page: 1 The Larson Electronics EPLC2-HB-50LED-RT Explosion Proof High Bay light
More informationFR-A180 FR-A360. Occupancy detector. Use
5 488 Occupancy detector with daylight sensor Occupancy detector with integral daylight sensor for demand-based control of HVAC systems and lighting. Adjustable switch-on and switch-off delay Adjustable
More informationActive Infrared Multi Beam Sensors
Active Infrared Multi Beam Sensors D Series TECHNICAL MANUAL INDEX GENERAL SAFETY RECOMMENDATIONS 3 CONFORMITY 4 WARRANTY 4 INTRODUCTION 5 FEATURES 5 OPERATIONAL RANGE 6 SETUP TRANSMITTER (TX) 6 SETUP
More informationElectro Optical Components, Inc.
Electro Optical Components, Inc. 5464 Skylane Boulevard, Suite D, Santa Rosa, CA 95403 Toll Free: 855-EOC-6300 www.eoc-inc.com info@eoc-inc.com Technical Note GUVx-T1XC-3LWx GUVx-T11GC-I8LWx Probe Application
More informationEx LED light fittings
About us TEP Ex is a regional leader in manufacturing of explosion-protected electrical equipment. Through continuous development of new products and markets, modernization of technology and investment
More informationUV - flame detector KLC 10 for oil -, gas- and dual fuel burners for intermittent burner operations
KLC 10 Technical information UV - flame detector KLC 10 for oil -, gas- and dual fuel burners for intermittent burner operations Description The KLC 10 is a compact UV flame detector, which has been developed
More informationIndustrial 100 Watt Ultraviolet LED Light Fixture - Paint Spray Booth Approved Nanometer
Industrial 100 Watt Ultraviolet LED Light Fixture - Paint Spray Booth Approved - 365 Nanometer Part #: GAU-HB-100LED-RT-UVA The Larson Electronics GAU-HB-100LED-RT-UVA Industrial Ultraviolet light fixture
More informationFIRE IR SENSOR Flame Detection
FIRE IR SENSOR Flame Detection Introduction Detects Open Flames Sensitive to Flickering IR or UV/IR Emissions from Flames Low Power 24Vdc Operation, 4-20mA or Relay Interface Why use Flame Detectors? Heat
More informationLFL Series Burner Flame Safeguard Control
LFL Series Burner Flame Safeguard Control Technical Instructions Document No. 74US LFL Rev. 2 November, 2004 The LFL is a compact electro-mechanical primary flame safeguard control designed to provide
More informationTransfer of Heat. There are three ways in which heat is transferred from one body to another. These are
Transfer of Heat In the precious chapter you have learnt that heat flows from a body at a higher temperature to a body at a lower temperature, but how does this transfer take place? You will find the answer
More informationmod. ERHSO712 mod. ERRHSO712 ENGLISH CONTROLLER mod. CSRLS MAINTENANCE ADDITIONAL CONTROLS
CONTENTS mod. ERHSO712 (Transmitter-Receiver version) Basic characteristics.......................................... 3 Product characteristics........................................ 3 Working Principle............................................
More informationSURFACE MOUNT LED 405 nm, 1206 UV IL PACKAGE
SURFACE MOUNT LED 405 nm, 1206 UV IL PACKAGE SM1206UV-405-IL Industry Standard 1206 Package RoHS Compliant UV Emitting LED Water Clear Lens Narrow Viewing Angle Ideal for Curing, Detection, and Medical
More informationActive Infrared Multi Beam Sensors. R Series
Active Infrared Multi Beam Sensors R Series TECHNICAL MANUAL INDEX GENERAL SAFETY RECOMMENDATIONS 3 CONFORMITY 4 WARRANTY 4 INTRODUCTION 5 FEATURES 5 OPERATIONAL RANGE 6 SETUP TRANSMITTER (TX) 6 SETUP
More informationR7824, R7847, R7848, R7849, R7851, R7852, R7861, R7886 Amplifiers for 7800 SERIES and R7140 Relay Modules
R7824, R7847, R7848, R7849, R7851, R7852, R7861, R7886 Amplifiers for 7800 SERIES and R7140 Relay Modules PRODUCT DATA indicate the presence of flame when used with 7800 SERIES and R7140 Relay Modules.
More informationVaporproof White LED Light - 10 Watts - Non-Metallic - Corrosion Resistant Lumens
Vaporproof White LED Light - 10 Watts - Non-Metallic - Corrosion Resistant - 1050 Lumens Part #: VPLED-CRNM-LED10W Page: 1 Made in the USA The VPLED-CRNM-LED10W Vaporproof White LED Light from Larson Electronics
More informationDEB71. Earth Leakage Monitoring Relay. Benefits. Description
Earth Leakage Monitoring Relay Benefits Adjustable trip level. Adjustable leakage threshold from 30mA to 5A or from 300mA to 30A. 2 outputs. Two relay outputs provide, besides the alarm signal an additional
More informationUSER MANUAL TUNGSTEN SMART-HEAT ELECTRIC WIRELESS DIMMER CONTROLLER BY BROMIC IMPORTANT
TUNGSTEN SMART-HEAT ELECTRIC WIRELESS DIMMER CONTROLLER BY BROMIC USER MANUAL Version 1.0 Doc. T744.01_EN (TEMP) TVHET916A07BK IMPORTANT READ THIS MANUAL CAREFULLY. SEE INSIDE COVER FOR IMPORTANT INFORMATION
More informationInstruction Manual. Alarm Unit For Low Gas Level # Read manual before use! Observe all safety information! Keep manual for future use!
Mess-, Regel- und Überwachungsgeräte für Haustechnik, Industrie und Umweltschutz Lindenstraße 20 74363 Güglingen Telefon +49 7135-102-0 Service +49 7135-102-211 Telefax +49 7135-102-147 info@afriso.de
More informationSLATE. UV Ampli-Check Flame Amplifier INSTALLATION INSTRUCTIONS R8001S1071
SLATE UV Ampli-Check Flame Amplifier R8001S1071 INSTALLATION INSTRUCTIONS Scan for more information Application SLATE brings configurable safety and programmable logic together into one single platform.
More informationSnifter ATEX22 VERSION. User Manual. Distributor
Snifter ATEX22 VERSION User Manual Distributor Version 1.4 09/09/2009 Table of Contents 1. INTRODUCTION... 3 1.1. Safety... 3 1.2. Product overview... 4 1.3. How does it work?... 4 2. INSTALLATION... 5
More informationQXA2100. Condensation monitor QXA2101. Monitor to prevent damage caused by condensation on chilled ceilings and HVAC plants with AC/DC 24 V power.
QXA2100 Condensation monitor QXA2100 Monitor to prevent damage caused by condensation on chilled ceilings and HVAC plants with AC/DC 24 V power. Application Monitors condensation build up in buildings
More informationFlame Monitor for Multiple Burner Furnaces D-LE 603 D-UG 660
Selectivity Adjustable by Means of - High Pass Frequency Filter - Gain - Threshold Different Adjustments for Different Conditions (e.g. According Fuel or Combustion Technology) Possible, to be Activated
More informationSP-4004 OPTICAL-ACOUSTIC OUTDOOR SIREN sp4004_en 03/13
SP-4004 OPTICAL-ACOUSTIC OUTDOOR SIREN sp4004_en 03/13 The SP-4004 siren provides information about alarm situations by means of optical and acoustic signaling. The device is designed for outdoor installation.
More informationUSER MANUAL TUNGSTEN SMART-HEAT ELECTRIC WIRELESS DIMMER CONTROLLER BY BROMIC IMPORTANT
TUNGSTEN SMART-HEAT ELECTRIC WIRELESS DIMMER CONTROLLER BY BROMIC USER MANUAL Version 1.2 US Doc. T646.01 TVHET916A06 IMPORTANT READ THIS MANUAL CAREFULLY. SEE INSIDE COVER FOR IMPORTANT INFORMATION ABOUT
More informationAO Annunciator Module
General Specifications GS48C43Z01-00E-N AO-543-01 Annunciator Module GENERAL Figure 1 This module has two independent annunciator circuits. The circuits handle fault signals and operator actions (acknowledge,
More information