Hazardous Location Supervised Warning Light

Transcription

1 FEDERAL SIGNAL CORPORATION Hazardous Location Supervised Warning Light Model 154XST RUGGED DESIGN FOR USE IN HAZARDOUS LOCATIONS Available in 24VDC Four wires and supervisory diode Six dome colors 10,000-hour high-intensity strobe 3 /4-inch pipe mount Dome guard included Type 4X, IP66 enclosure Marine Rated Supervisable 4-wire power circuit CSFM Approved CSA Certified for indoor/outdoor use UL and cul Listed Federal Signal s Model 154XST hazardous location strobe light provides 80 high-intensity flashes per minute. This warning light is available in 24VDC with a 4-wire supervisable power circuit for fire alarm and suppression supervised control panels. The Model 154XST strobe light is UL and cul Listed and CSA Certified for Class I, Division 2, Groups A, B, C and D; Class II, Division 1, Groups E, F and G; and Class III. The 154XST meets Type 4X water-tight, dust-tight, and corrosionresistant requirements; constructed to IP66. This hazardous location warning light has an aluminum base, coated for corrosionresistance that is ready for mounting on a 3 /4-inch pipe. The Dome Guard (included) fits over the glass dome to protect it against accidental collision with moving equipment, such as forklifts. The 154XST contains a diode and four wire leads for use in fire alarm applications. The 154XST has an effective candela (ECP) of 165 and a 520,000 peak candela. It is available in six dome colors, including amber, blue, clear, green and red (magenta upon request). Federal Signal s rugged 154XST strobe warning light is specifically designed for hazardous locations or corrosive environments where a very bright visual signal is required. This warning light can be used for plant evacuation or other communication needs. Current Flash Rate/ Candela Model Voltage Draw Minute Peak 154XST 24VDC 0.60 amps ,000 1 Peak candela is the maximum light intensity generated by a flashing light during its light pulse 2 ECP (Effective Candela) is the intensity that would appear to an observer if the light were burning steadily 5 yr 5W A R R A N T Y

2 HAZARDOUS LOCATION STROBE LIGHT (154XST) 5.5"/139.7 mm Dome Guard (Included) Glass Dome Strobe Tube 9.25"/ 235 mm Gasket Aluminum Base 3/4" Pipe Mount Power Wires SPECIFICATIONS Lamp Life*: 10,000 Hours 10,000 Hours Lamp Style Strobe Strobe Operating Temperature: -31 F to 150 F -35 C to 66 C Net Weight: 3.8 lbs. 1.7 kg Shipping Weight: 4.5 lbs. 2.0 kg Height: 9.25" 235 mm Diameter: 5.5" mm HOW TO ORDER Specify model, voltage and color Please refer to Model Number Index 154XST beginning on page 381 * Optimal hours under ideal conditions. REPLACEMENT PARTS Description Part Number Description Part Number Series C Dome and Ring Assembly* Dome & Ring Assembly, Amber K C-01 PC Assembly, 24VDC K A Dome & Ring Assembly, Blue K C-02 Strobe Tube K149122B Dome & Ring Assembly, Clear K C-04 Dome Gaskets K B Dome & Ring Assembly, Green K C-03 Guard K B Dome & Ring Assembly, Red K C Dome & Ring Assembly, Magenta K C-05 * Call the factory for Series A and B part numbers Federal Signal Dr., University Park, IL Tel: Fax:

3 FEDERAL SIGNAL CORPORATION Electraray Supervised Hazardous Location Strobe Warning Light Model 224XST DESIGNED FOR USE IN HAZARDOUS LOCATIONS 24VDC Four wires and supervisory diode Six lens colors 10,000 hour, high-intensity strobe tube 1 /2 - inch pipe mount Type 4X, IP66 enclosure CSFM Approved CSA Certified UL and cul Listed Federal Signal s Electraray Model 224XST hazardous location strobe light provides 80 high-intensity flashes per minute. This warning light is available in 24VDC. The Model 224XST has been certified by UL as meeting Type 4X watertight and corrosion resistant requirements, constructed to IP66. This hazardous location warning light has a black polyurethane coated base and the inner fresnel lens is available in six colors (including magenta). The clear polycarbonate outer dome can be quickly removed for easy access to inspect the unit or change the lamp. The 224XST has an effective candela of 240 and a 580,000 peak candela. The 224XST is UL Listed, CSA Certified and CSFM Approved for Class I, Division 2, Groups A, B, C and D; Class II, Division 2, Groups F and G; and Class III. The 24VDC 224XST features a voltage in-rush limiting PCB design that provides greater compatibility control systems and less electrical interference with in-rush sensitive devices. The Electraray 224XST contains a supervisory diode and four wire leads, for fire alarm applications. Model 224XST is ideal for wet, corrosive atmospheres like those found in food processing industries, or anywhere a visual signal is needed. Federal Signal s affordable Electraray Strobe Warning Light is specifically designed for use in hazardous locations or where corrosive materials are present. Operating Flash Rate/ Candela Model Voltage Current Minute Peak 1 ECP 2 Mount 224XST 24VDC 0.7 amps , /2" Pipe (2.0 amp, in-rush) 5 yr 5W A R R A N T Y 1 Peak candela is the maximum light intensity generated by a flashing light during its light pulse 2 ECP (Effective Candela) is the intensity that would appear to an observer if the light were burning steadily

4 ELECTRARAY HAZARDOUS LOCATION WARNING LIGHT (224XST) 5.5"/139.7 mm Outer Dome Strobe Tube Inner Fresnel Lens 7.5"/190.5 mm 1/2" Pipe Mount Retaining Screw SPECIFICATIONS Lamp Life*: 10,000 Hours 10,000 Hours Lamp Style: Strobe Strobe Operating Temperature: -31 F to 150 F -35 C to 66 C Net Weight: 1.5 lbs kg Shipping Weight: 2.0 lbs. 0.9 kg Height: 7.5" mm Diameter: 5.5" mm HOW TO ORDER Specify model, voltage and color Please refer to Model Number Index 224XST beginning on page 381 * Optimal hours under ideal conditions. REPLACEMENT PARTS Description Part Number Description Part Number Interior Lens Exterior Dome, Clear K8444D219C-04 Amber K8550C095A-02 PC Assembly, 24VDC K C-01 Blue K8550C095A-01 Strobe Tube K A Clear K8550C095A Green K8550C095A-04 Magenta K8550C095A-07 Red K8550C095A Federal Signal Dr., University Park, IL Tel: Fax:

5 FEDERAL SIGNAL CORPORATION Electraray Supervised Hearing Impaired Hazardous Location Strobe Warning Light Model 224XSTHI DESIGNED FOR USE IN HAZARDOUS LOCATIONS Available in 24VDC Four wires and supervisory diodes Clear lens 10,000 hour, high-intensity strobe tube 1 /2 - inch pipe mount Type 4X, IP66 enclosure UL Listed and CSFM Approved Federal Signal s Electraray Model 224XSTHI hazardous location strobe light provides 80 high-intensity flashes per minute. This warning light is available in 24VDC. The Model 224XSTHI has been certified by UL as meeting Type 4X water tight and corrosion resistant requirements, constructed to IP66. This hazardous location warning light has a black polyurethane-coated base and a clear inner fresnel lens to meet the requirements of Hearing Impaired Signals. The clear polycarbonate outer dome can be quickly removed for easy access to inspect the unit or change the lamp. The 224XSTHI has an effective candela of 240 and a 580,000 peak candela. The 224XSTHI features a voltage in-rush limiting PCB design that provides greater compatibility with control systems and fire alarm panels and less electrical interference with in-rush sensitive devices. The 224XSTHI warning light is UL Listed for Class I, Division 2, Groups A, B, C and D; Class II, Division 2, Groups F and G; and Class III. The 224XSTHI is also CSFM Approved. The Electraray 224XSTHI contains a supervisory diode and four wire leads for fire alarm applications. This strobe is UL 1971 Listed for hearing impaired applications. Operating Flash Rate/ Candela Model Voltage Current Minute Peak 1 ECP 2 Mount 224XST-HI 24VDC 0.7 amps , /2" Pipe (2.0 amp, in-rush) 1 Peak candela is the maximum light intensity generated by a flashing light during its light pulse 2 ECP (Effective Candela) is the intensity that would appear to an observer if the light were burning steadily 5 yr 5W A R R A N T Y

6 ELECTRARAY HAZARDOUS LOCATION WARNING LIGHT (224XSTHI) 5.5"/139.7 mm Outer Dome Strobe Tube Inner Fresnel Lens 7.5"/190.5 mm 1/2" Pipe Mount Retaining Screw SPECIFICATIONS Lamp Life*: 10,000 Hours 10,000 Hours Lamp Style: Strobe Strobe Operating Temperature: -31 F to 150 F -35 C to 66 C Net Weight: 1.5 lbs kg Shipping Weight: 2.0 lbs. 0.9 kg Height: 7.5" mm Diameter: 5.5" mm HOW TO ORDER Specify model, voltage and color Please refer to Model Number Index 224XSTHI beginning on page 381 * Optimal hours under ideal conditions. REPLACEMENT PARTS Description Part Number Description Part Number Exterior Dome, Clear K8444D219C-04 PC Assembly, 24VDC K C-01 Interior Lens, Clear K8550C095A Strobe Tube K A 2645 Federal Signal Dr., University Park, IL Tel: Fax:

7 FEDERAL SIGNAL CORPORATION Explosion-Proof Strobe Light Model 27XST DESIGNED FOR USE IN EXPLOSION-PROOF ATMOSPHERES Available in 24VDC Six lens colors 10,000 hour strobe tube 3 /4 - inch pendant mount standard; other options available Dome guard optional Type 4X, IP66 enclosure Supervisable power and low in-rush circuit Marine Rated CSFM Approved CSA Certified UL and cul Listed Federal Signal s Model 27XST explosion-proof strobe light produces 80 high-intensity flashes per minute. This warning light operates on 24VDC only. The 27XST is UL Listed for Class I, Division 1, Groups C & D; Class II, Division 1, Groups E, F & G; Class I, Division 2, Groups A, B; and Class III. The 27XST is CSA Certified and Marine Rated. The 24VDC 27XST features a voltage in-rush limiting PCB design that provides greater compatibility with factory automation control systems and less electrical interference with in-rush sensitive devices. It s diode polarized power circuit also makes it ideal for fire alarm and suppression supervised control panels. The 27XST is Type 4X rated; constructed to IP66. Corrosion resistance is achieved with a powder epoxy finish applied over the copper-free aluminum housing. All exposed hardware is 316 grade stainless steel. Federal Signal s Model 27XST has an effective candela (ECP) of 850 and a two million peak candela. A pendant mount is supplied and a ceiling mount and 90 wall mount are available options. For easy installation, the mounting box is first installed and the fixture is then threaded onto the mounting box, making the electrical connection. Electrical continuity is made when five threads are engaged. Federal Signal s Model 27XST is specifically designed for explosion-proof atmospheres and/or corrosive environments. Because it is easy to install and requires very low maintenance, it is ideal for use in areas such as oil rigs, mines, refineries, and chemical plants. Operating Flash Rate/ Candela Model Voltage Current Minute Peak 1 ECP 2 Mount 27XST 24VDC 1.9 amps 80 2,000, /4" Pendant (3.0 amp, in-rush) 5 yr 5W A R R A N T Y 1 Peak candela is the maximum light intensity generated by a flashing light during its light pulse 2 ECP (Effective Candela) is the intensity that would appear to an observer if the light were burning steadily

8 EXPLOSION-PROOF STROBE LIGHT (27XST) 3/4 Pendant 4.5"/ mm Electrical Connection Block 4"/101.6 mm Cast Aluminum Corrosion Resistant Explosion-Proof Housing 15.63"/397 mm High Intensity Strobe Tube Fresnel Lens Glass Dome 6.36"/162 mm 8.82"/224 mm SPECIFICATIONS Lamp Life*: 10,000 hours 10,000 hours Lamp Style: Strobe Strobe Net Weight: 14 lbs. 6.4 kg Shipping Weight: 18.1 lbs. 8.2 kg Height: 15.63" mm Diameter: 8.82" mm * Optimal hours under ideal conditions. HOW TO ORDER Specify model, voltage and color Specify options: Dome Guard (DGXC) Ceiling Mount (CMXC) Wall Mount (WMXC) Please refer to Model Number Index 27XST beginning on page 381 REPLACEMENT PARTS Description Part Number Description Part Number Exterior Dome Assembly, Clear K8444C271A-01 24VDC Mechanism K F-03 Interior Lens Assembly, Amber K8550C095A-02 Strobe Tube K A Interior Lens Assembly, Blue K8550C095A-01 Interior Lens Assembly, Clear K8550C095A Interior Lens Assembly, Green K8550C095A-04 Interior Lens Assembly, Red K8550C095A-03 Interior Lens Assembly, Magenta K8550C095A Federal Signal Dr., University Park, IL Tel: Fax:

9 FEDERAL SIGNAL CORPORATION SelecTone Audible Signaling Device Models 304GC and 314GC PLANT-WIDE WARNING AND VOICE COMMUNICATION Available in 24VDC Built-in gain control Digital signal amplification Fused input and output Type 3R enclosure 4-wire supervisable power circuit UL Listed and CSFM Approved The Federal Signal Models 304GC and 314GC Amplified Speakers are designed to produce crisp, clear tones in supervised alarm notification systems. These amplified speakers can broadcast tones generated by a tone card installed into the speaker (the plug-in 32-tone UTM) or by a central tone source in a voice evacuation or paging system. When live public address or voice messages are required, plug-in Connector Cards (AM25CK or AM70CK) interface with the VRMS of the EVAC panel. Both speaker amplifiers are compatible with fire alarm and suppression supervised control panels and power boosters. The speaker cone and projector are constructed of rugged spun aluminum. The solid-state amplifier circuit is protected in a die-cast aluminum housing. Dust- and moisture-proof gaskets provide protection from the elements. All external surfaces are sealed with gray powder coat paint. The 304GC is easily installed on any flat surface. Both the 304GC and 314GC are UL Listed for use indoors and out. The rugged construction and high output of the Models 304GC and 314GC make it ideal for use in harsh environments with high ambient noise levels. Both models feature an internal gain control for adjustment to the suit area. Operating Standby Decibels per UL1480 Decibels on Axis Model Voltage Current Current 10' 1m 10 1m 304GC 24VDC 0.7 amps 0.15 amps GC 24VDC 1.3 amps 0.15 amps yr 5W A R R A N T Y

10 SELECTONE AUDIBLE SIGNALING DEVICE (304GC/314GC) 304GC 7.9 /200 mm Reentrant Trumpet-Type Loudspeaker Spun Aluminum Projector 12.4"/ 314 mm Fully Gasketed Die- Cast Aluminum Housing Full Speaker Rotation 4.9 /125 mm 8.5"/216 mm 10.2"/258 mm Reentrant Trumpet-Type Loudspeaker 13.9"/ 353 mm Spun Aluminum Projector Fully Gasketed Die Cast Aluminum Housing Full Speaker Rotation 314GC SPECIFICATIONS 4.9 /125 mm 304GC Operating Temperature: -40 F to 150 F -40 C to 66 C Net Weight: 4.5 lbs. 2.0 kg Shipping Weight: 5.7 lbs. 2.6 kg Height: 12.4" mm Width: 7.9" mm Depth: 8.5" mm 314GC Operating Temperature: -40 F to 150 F -40 C to 66 C Net Weight: 6.1 lbs. 2.8 kg Shipping Weight: 7.5 lbs. 3.4 kg Height: 13.9" mm Width: 10.2" mm Depth: 9.9" mm 9.9"/252 mm HOW TO ORDER Specify model number and voltage Tone Card (UTM) Specify Connector Kit for use in systems Supervised Connector Kit (300CKS) 25VRMS Connector Kit (AM25CK) Please refer to Model Number Index 304GC/314GC beginning on page 381 REPLACEMENT PARTS Description Part Number 304GC Amplifier Assembly K A Voice Coil Series B K A Speaker Assembly K A 4 Pos connector K140340B 314GC Amplifier Assembly K A-01 Voice Coil Series B K A Speaker Assembly K A 4 Pos connector K140340B 2645 Federal Signal Dr., University Park, IL Tel: Fax:

11 FEDERAL SIGNAL CORPORATION SelecTone Hazardous Location Audible Signaling Device Models 304GCX and 314GCX DESIGNED FOR USE IN HAZARDOUS LOCATIONS Available in 24VDC Reliable, solid-state circuitry Built-in gain control Digital signal amplification Fused input and output Type 4X enclosure External mounting tabs 4-wire supervisable power circuit UL Listed and CSFM Approved Federal Signal Models 304GCX and 314GCX Hazardous Location Amplified Speakers are designed to produce crisp, clear tones in supervised alarm notification systems. Both speakers amplifiers are compatible with fire alarm, voice evacuation, suppression supervised control panels and power boosters. These amplified speakers can broadcast tones generated by a Tone Card installed into the speaker (the plug-in 32-tone UTM) or by a central tone source in a voice evacuation or paging system. When live public address or voice messages are required, plug-in Connector Cards (AM25CK or AM70CK) interface with the audio output of the EVAC panel. The speaker cone and projector are constructed of rugged spun aluminum. The solid-state amplifier circuit is protected in a die-cast aluminum housing. Dust and moisture-proof gaskets provide protection from the elements. All external surfaces are sealed with gray powder coat paint. The 304GCX and 314GCX are easily installed with external mounting tabs. The 304GCX and 314GCX are UL Listed for Class I, Division 2, Groups A, B, C and D; Class II, Division 2, Groups F & G; and Class III. The rugged construction and high output of the Model 304GCX and 314GCX make it ideal for use in harsh environments with high ambient noise levels. Both models feature an internal gain control for adjustment to suit area. Operating Standby Decibels per UL1480 Decibels on Axis Model Voltage Current Current 10' 1m 10 1m 304GCX 24VDC 0.7 amps 0.15 amps GCX 24VDC 1.3 amps 0.15 amps yr 5W A R R A N T Y

12 HAZARDOUS LOCATION AUDIBLE SIGNALING DEVICE (304GCX/314GCX) 304GCX 7.9 /200 mm Reentrant Trumpet-Type Loudspeaker Spun Aluminum Projector 12.4"/ 314 mm Plug-in Tone Module (purchased separately) Full Speaker Rotation 4.9 /125 mm 8.5"/216 mm 10.2"/258 mm Reentrant Trumpet-Type Loudspeaker 13.9"/ 353 mm Spun Aluminum Projector Plug-in Tone Module (purchased separately) Full Speaker Rotation 314GCX 6.0 /152 mm 9.9"/252 mm SPECIFICATIONS 304GCX Operating Temperature: -40 F to 150 F -40 C to 66 C Net Weight: 4.5 lbs. 2.0 kg Shipping Weight: 5.7 lbs. 2.6 kg Height: 12.4" mm Width: 7.9" mm Depth: 8.5" mm 314GCX Operating Temperature: -40 F to 150 F -40 C to 66 C Net Weight: 6.1 lbs. 2.8 kg Shipping Weight: 7.5 lbs. 3.4 kg Height: 13.9" mm Width: 10.2" mm Depth: 9.9" mm HOW TO ORDER Specify model number and voltage Tone Card (UTM) Specify Connector Kit for use in systems: Supervised Connector Kit (300CKS) 25VRMS Connector Kit (AM25CK) Please refer to Model Number Index 304GCX/314GCX beginning on page 381 REPLACEMENT PARTS Description Part Number 304GCX Amplifier Assembly K A Voice Coil, Series B K A Speaker Assembly K A 4 Pos connector K140340B 314GCX Amplifier Assembly K A-01 Voice Coil, Series B K A Speaker Assembly K A 4 Pos connector K140340B 2645 Federal Signal Dr., University Park, IL Tel: Fax:

13 FEDERAL SIGNAL CORPORATION SelecTone Explosion-Proof Audible Signaling Device Models 304X and 314X DESIGNED FOR EXPLOSION- PROOF ENVIRONMENTS Available in 24VDC Built-in gain control 4-wire supervisable power circuit IP65, NEMA 4X Approved UL Listed and CSFM Approved The Federal Signal Model 304X and 314X Explosion Proof Amplified Speakers are designed to produce crisp, clear tones in supervised alarm notification systems. Both models are compatible with fire alarm, voice evacuation, suppression supervised control panels, and power boosters. These amplified speakers can broadcast tones generated by a Tone Card installed into the speaker (the plug-in 32-tone UTM) or by a central tone source in a voice evacuation or paging system. When live public address or voice messages are required, plug-in Connector Cards (AM25CK or AM70CK) interface with the VRMS of the EVAC panel. The speaker cone and projector are constructed of rugged spun aluminum. The solid-state amplifier circuit is protected in a die-cast aluminum housing. Dust- and moisture-proof gaskets provide protection from the elements. All external surfaces are sealed with gray powder coat paint. A heavy-duty swivel mount bracket allows the installer to direct the output effectively. The 304X and 314X are UL Listed for Class I, Division 1, Groups B, C & D. The rugged construction and high output of the Model 304X and 314X make them ideal for use in harsh environments with high ambient noise levels. Both models feature an internal gain control for adjustment to suit area. Operating Standby Decibels per UL1480 Decibels on Axis Model Voltage Current Current 10' 1m 10 1m 304X 24VDC 0.7 amps 0.13 amps X 24VDC 1.0 amps 0.13 amps yr 5W A R R A N T Y

14 EXPLOSION-PROOF AUDIBLE SIGNALING DEVICE (304X/314X) 304X 16.3"/415 mm 13.1"/ 332 mm CAUTION Spun Aluminum Projector 17"/ 431 mm Cast Aluminum Explosion Proof Housing 19.5"/496 mm Adjustable Mounting Bracket Mounting Bracket Detail 1.5"/ 38 mm 5.53"/ 140 mm 0.53"/ 13 mm 2.47"/ 63 mm 314X Cast Aluminum Explosion Proof Housing CAUTION Adjustable Mounting Bracket Spun Aluminum Projector Mounting Bracket Detail 1.5"/ 38 mm 5.53"/ 140 mm 16.7"/ 425 mm 18.8"/ 478 mm 0.53"/ 13 mm 2.47"/ 63 mm SPECIFICATIONS 304X Operating Temperature: -40 F to 150 F -40 C to 66 C Net Weight: 15.4 lbs. 7.0 kg Shipping Weight: 22.8 lbs kg Height: 17.0" mm Width: 13.1" mm Depth: 16.3" mm 314X Operating Temperature: -40 F to 150 F -40 C to 66 C Net Weight: 16.4 lbs. 7.4 kg Shipping Weight: 32.4 lbs kg Height: 18.8" mm Width: 16.7" mm Depth: 19.5" mm Ingress Protection: IP65 and NEMA 4X Approved HOW TO ORDER Specify model number Tone Card (UTM) Specify Connector Kit for use in systems Supervised Connector Kit (300CKS) 25 VRMS Connector Kit (AM25CK) Please refer to Model Number Index 304X/314X beginning on page 381 REPLACEMENT PARTS Description Part Number 304X Amplifier Assembly K A-01 Horn Assembly K A Driver Assembly K A Cover Assembly K A Mounting Bracket Assembly K A 4 Pos connector K140340B 314X Amplifier Assembly K A-02 Horn Assembly K A 4 Pos connector K140340B 2645 Federal Signal Dr., University Park, IL Tel: Fax:

15 FEDERAL SIGNAL CORPORATION SelecTone Audible Signaling Devices Models 54GC and 54GCB DESIGNED FOR INDOOR AND OUTDOOR USE Available in 24VDC Solid-state circuitry Built-in gain control Produces 0dBc to 10 (0dBc to 1m) Flush or surface mount Type 3R enclosure 4-wire supervisable power circuit UL Listed and CSFM Approved Federal Signal s Model 54GC and 54GCB SelecTone Speaker Amplifiers are designed to provide crisp, clear tones in supervised alarm notification systems. In the Models 54GC, a short, folded re-entrant horn is interposed between the diaphragm and surrounding air space. This design provides optimal db output and very good frequency response. The 54GC is UL Listed. It has been designed, tested and approved for use in Type 3R applications. When installed with the Model WB Weatherproof Backbox, the 54GC is suitable for use outdoors. The compact size and attractive appearance of the Model 54GC makes it ideal for use in offices, hallways, reception and plant areas where ambient noise levels are not exceedingly high, and even sound dispersal is desired. The 54GCB is designed for areas without high ambient noise levels, such as offices, hallways and reception areas. The baffle allows the four-inch speaker to be installed easily in any suspended ceiling plenum with a Model R4NB backbox. The white grill of the 54GCB is attractive in most decors. Internal gain control allows output adjustment from 0dBc to a maximum of 86dBc at 10 feet. SelecTone Speaker Amplifiers are used individually or as part of a plant-wide emergency notification system. The Model UTM Universal Tone Module, with 32 tones is plugged into a single SelecTone Speaker Amplifier for stand-alone use or into a SelecTone Command Unit for plant-wide signaling. 5 yr 5W A R R A N T Y Operating Standby Decibels per UL1480 Decibels on Axis Model Voltage Current Current 10' 1m 10 1m 54GC 24VDC amps amps GCB 24VDC amps amps

16 SELECTONE AUDIBLE SIGNALING DEVICE (54GC/54GCB) FBL * 7.23"/183.6 mm 2.53"/ 64.3 mm 54GC with Trim Plate (included) and NBL Knock- Out Box FG * 54GC with FG Grille and FBL Box White Baffle Grille Tone Module Slot Gain Control 54GC 54GC with Trim Plate (included) and WB Back Box 54GCB SPECIFICATIONS 54GC Operating Temperature: -31 F to 161 F -35 C to 72 C Net Weight: 1.7 lbs. 0.8 kg Shipping Weight: 2.2 lbs. 1.0 kg Height : 4.5" mm Width: mm Depth: mm 54GCB Operating Temperature: -31 F to 161 F -35 C to 72 C Net Weight: 1.6 lbs kg Shipping Weight: 2.3 lbs kg Depth : 2.53" 64.3 mm Diameter: mm HOW TO ORDER Specify Model Specify Tone Module for stand alone operation Universal Tone Module (UTM) Specify Connector Kit for use in systems. (Call factory for system design assistance.) Connector Kit (300CK) Supervised Connector Kit (300CKS) 25VRMS Connector Kit (AM25CK) Specify Options: Knock-out Back Box (NBL) Weatherproof Back Box (WB) Grille (FG) Flush Mount Back Box (FBL) Ceiling Back Box (R4NB) Please refer to Model Number Index 54GC/54GCB beginning on page Federal Signal Dr., University Park, IL Tel: Fax:

17 FEDERAL SIGNAL CORPORATION Fireball Supervised Strobe Warning Light Model FB24ST LIGHT DUTY STROBE LIGHT Available in 24VDC Four wires and supervisory diode Six dome colors 10,000 hour strobe tube Integrated 1 /2 - inch pipe and surface mount Type 4X, IP66 enclosure CSFM Approved CSA Certified UL and cul Listed Federal Signal s brightest and most compact strobe light, the Fireball Supervised Warning Light emits a powerful "lightning bolt" flash of light. Approximately five inches tall and four inches in diameter and rated at 300 effective candela, the FB24ST is an economical solution to a wide variety of stationary requirements. The Fireball is available in 24VDC. All models are UL and cul Listed, CSA Certified and CSFM Approved. The 24VDC FB24ST features a voltage in-rush limiting PCB design that provides greater compatibility with control systems and less electrical interference with in-rush sensitive devices. The FB24ST features a unique dome that twists off easily for quick dome and lamp replacements. The newly redesigned base features an integrated 1 /2-inch pipe mount boss as well as the three holes required for surface mount configurations. Black epoxy paint is electrostatically applied to the base for superior corrosion resistance. The Fireball dome and base design provides a watertight, dust-tight and corrosion resistant Type 4X rating. The FB24ST contains a supervisory diode and four wire leads, for use in fire alarm applications. The FB24ST can be used in any application where a superior visual signal is needed. It is especially effective in the warning of industrial hazards, process control, status indication and in areas with high ambient noise levels. Federal Signal s Fireball Supervised Strobe is a very lowmaintenance warning light for industrial applications where a vibration-resistant light is required to signal an emergency or process status. 5 yr 5W A R R A N T Y Operating Flash Rate/ Candela Model Voltage Current Minute Peak 1 ECP 2 Mount FB24ST 24VDC 0.7 amps 80 1,000, /2" Pipe/Surface (2.0 amp, in-rush) 1 Peak candela is the maximum light intensity generated by a flashing light during its light pulse 2 ECP (Effective Candela) is the intensity that would appear to an observer if the light were burning steadily

18 FIREBALL STROBE WARNING LIGHT (FB24ST) 4.1"/100.1 mm Impact-Resistant Fresnel Dome High-Powered Strobe Tube 5.25"/133.4 mm Easy-Access Twist-off Dome Built-In Strobe Power Supply 1/2" Pipe Mount and 3-hole Surface Mount SPECIFICATIONS Lamp Life*: 10,000 Hours 10,000 Hours Lamp Style: Strobe Strobe Operating Temperature: -31 F to 150 F -35 C to 66 C Net Weight: 1.45 lbs. 0.7 kg Shipping Weight: 1.7 lbs. 0.8 kg Height: 5.25" mm Diameter: 4.1" mm * Optimal hours under ideal conditions. HOW TO ORDER Specify model, voltage and color Specify options: Corner Bracket (LCMB2)* Wall Bracket (LWMB2)* Please refer to Model Number Index FB24ST beginning on page 381 * Brackets not Type 4X rated. REPLACEMENT PARTS Description Part Number Description Part Number Dome, Amber K A PC Assembly, 24VDC K C Dome, Blue K A-01 Strobe Tube, Series A, A1, A2, A3 Call Factory Dome, Clear K A-02 Strobe Tube, Series A4, A5, B K A Dome, Green K A-03 Dome, Red K A-04 Dome, Magenta K A Federal Signal Dr., University Park, IL Tel: Fax:

19 FEDERAL SIGNAL CORPORATION Fireball Supervised Hearing Impaired Strobe Warning Light Model FB24STHI LIGHT DUTY STROBE LIGHT Available in 24VDC Four wires and supervisory diode Clear dome 10,000 hour strobe tube Integrated 1 /2 - inch pipe mount and surface mount Type 4X, IP66 enclosure In-rush protected UL1971 Listed UL Listed and CSFM Approved Federal Signal s brightest and most compact strobe light, this supervised FireBall emits a powerful "lightning bolt" flash of light. Approximately five inches tall and four inches in diameter and rated at 300 effective candela, the FB24STHI is economical and effective. The Fireball is available in 24VDC, this model is UL Listed and CSFM Approved. The FB24PSTHI features a voltage in-rush limiting PCB design that provides greater compatibility with control systems and panels and less electrical interference with in-rush sensitive devices. The FB24STHI features a clear dome that twists off easily for quick dome and lamp replacements. The newly redesigned base features an integrated 1 /2" pipe mount boss as well as the three holes required for surface mount configurations. Black epoxy paint is electrostatically applied to the base for superior corrosion resistance. The Fireball dome and base design provides a watertight, dust-tight and corrosion resistant Type 4X rating. The Fireball FB24STHI contains a supervisory diode and four wire leads, for use in fire alarm applications. This strobe is UL 1971 listed, for hearing impaired applications. Operating Flash Rate/ Candela Model Voltage Current Minute Peak 1 ECP 2 Mount FB24STHI 24VDC 0.7 amps 80 1,000, /2" Pipe/Surface (2.0 amp, in-rush) 1 Peak candela is the maximum light intensity generated by a flashing light during its light pulse 2 ECP (Effective Candela) is the intensity that would appear to an observer if the light were burning steadily 5 yr 5W A R R A N T Y

20 FIREBALL STROBE WARNING LIGHT (FB24STHI) 4.1"/100.1 mm Impact-Resistant Fresnel Dome High-Powered Strobe Tube 5.25"/133.4 mm Easy-Access Twist-off Dome Built-In Strobe Power Supply 1/2" Pipe Mount and 3-hole Surface Mount SPECIFICATIONS Lamp Life*: 10,000 Hours 10,000 Hours Lamp Style: Strobe Strobe Operating Temperature: -31 F to 150 F -35 C to 66 C Net Weight: 1.45 lbs. 0.7 kg Shipping Weight: 1.7 lbs. 0.8 kg Height: 5.25" mm Diameter: 4.1" mm * Optimal hours under ideal conditions. HOW TO ORDER Specify model, voltage and color Specify options: Corner Bracket (LCMB2)* Wall Bracket (LWMB2)* Please refer to Model Number Index FS24STHI beginning on page 381 * Brackets not Type 4X rated. REPLACEMENT PARTS Description PC Assembly, 24VDC Dome, Clear Strobe Tube Part Number K C K A-02 K A 2645 Federal Signal Dr., University Park, IL Tel: Fax:

21 FEDERAL SIGNAL CORPORATION HEAT DETECTORS Model FSF100SB and FSF101SB RATE-OF-RISE AND FIXED TEMPERATURE DETECTORS Rate-of-rise and fixed temperature standard Compatible with most analog fire alarm panels Visual indication when element is activated Low profile design Simple push and twist removal Meets NFPA-72 requirements CSFM Approved UL and ULC Listed Heat detectors are a necessary part of any fire alarm system. Federal Signal models FSF100SB and FSF101SB Heat Detectors provide a durable, architecturally pleasing solution. Each detector is available with, as standard, both rate-of-rise and fixed temperature sensors. The FSF100SB Heat Detector contains a 135 fixed temperature element and the FSF101SB Heat Detector contains a 200 fixed temperature element. Rate-of-rise refers to how quickly the detector will sense a rapid rise in temperature and close its contacts. The pneumatic rateof-rise element within the FSF100SB and FSF101SB will respond to a rise in temperature, approximately 15 F (8 C) per minute, by measuring the expansion of air within a sealed chamber. This increase in pressure depresses a diaphragm, causing an electrical contact to close the circuit. In addition to the rate-of-rise detection, each model has a fixed temperature element. The fixed temperature element incorporates a fusible alloy. When activated, the external heat collector drops away to provide quick visual confirmation that the element has operated. Each FSF Heat detector incorporates a slim profile, designed to be unobtrusive and minimize potential overhead obstruction. The included mounting plate is designed to fit a 4" square junction box, 3 1 /4" octagon box or plaster ring and adapts easily to uneven mounting surfaces. 5 yr 5W A R R A N T Y Voltage Contact Model Range Rating FSF100SB & FSF101SB 6-125VAC 6-28VDC 3.0 amps 1.0 amps 125VDC 0.3 amps 250VDC 0.1 amps

22 HEAT DETECTORS (FSF100SB/FSF101SB) 5.25 /13.4 cm 1.36 /3.45 cm SPECIFICATIONS Color: White Net Weight: 1.0 lbs gm Height 1.36" 3.45 cm Width: 5.25" 13.4 cm HOW TO ORDER Specify model number Please refer to Model Number Index FSF100SB/FSF101SB beginning on page 381 IMPORTANT NOTES 1. Heat detectors should be used for property protection. Where Life Safety is also involved, smoke detectors should also be used. 2. Each heat detector should be electronically supervised with battery back-up at the main fire alarm panel. 3. The rate-of-rise mechanism may be subject to reduced sensitivity over time. Annual testing of the rate-of-rise operation is recommended Federal Signal Dr., University Park, IL Tel: Fax:

23 FEDERAL SIGNAL CORPORATION Fire Alarm Pull Stations Models FSF102 and FSF103 RELIABLE ACTIVATION OF EMERGENCY SYSTEMS Available in 125VAC Single and Dual Action Mounts to 4" square or single gang electrical box UL Listed, CSFM and FM Approved Federal Signal Fire Alarm Pull Stations are designed for a long life of reliable service in a wide variety of environments, including industrial. The Model FSF103 Single Action Pull Station is activated quickly and easily by pulling down the t-handle. The Model FSF102 Dual Action Pull Station is activated by first lifting the metal cover then pulling the t-handle. This two-stage process is designed to minimize accidental or malicious alarm activations. The Federal Signal Pull Stations will operate as break-glass or non-break glass stations. Glass rods ship with each unit and are installed easily. Replacement rods are readily available. Each Pull Station is constructed of die cast aluminum and sealed with very visible red paint. Both can be mounted to 4 square or single gang electrical boxes. Screw terminals provide easy completion of the wiring. These heavy duty Pull Stations are suitable for use in industrial, municipal and educational environments. Contact Contact Model Description Voltage Type Rating FSF102 Dual Action 125VAC SPST NO 10 amps FSF103 Single Action 125VAC SPST NO 10 amps 5 yr 5W A R R A N T Y

24 FIRE ALARM PULL STATIONS (FSF102/FSF103) 3.21"/81.5 mm 2.25"/57.2 mm 4.78"/ mm FSF103 FSF102 SPECIFICATIONS Net Weight: FSF lbs kg FSF lbs kg Shipping Weight: FSF lbs kg FSF lbs kg Height: FSF " mm FSF " mm Width: FSF " 86.6 mm FSF " 81.5 mm Depth: FSF " 59.7 mm FSF " 57.2 mm HOW TO ORDER Specify model Please refer to Model Number Index FSF102/FSF103 beginning on page 381 REPLACEMENT PARTS Description Glass Rod (Qty 1) Part Number K288919A 2645 Federal Signal Dr., University Park, IL Tel: Fax:

25 FEDERAL SIGNAL CORPORATION Selectable Fire Alarm Horn and Chime Model FSF104 and FSF105 INDOOR AUDIBLE INDICATION Designed to meet or exceed NFPA requirements Universal mounting plate adapts to 4" square, single-gang, doublegang or octagon back box Low profile design Supervisable polarized design Field selectable audible tones in both chime and horn versions Can be synchronized using FSF206 Synchronization Module FSF104 is ULC Listed CSFM Approved UL listed for wall mount Federal Signal Models FSF104 Selectable Horn and FSF105 Selectable Chime are designed to provide local audible indication indoors when activated by a Fire Alarm Control Panel. Each model can be synchronized to work simultaneously with other units and each complies with NFPA requirements and UL categories 464 and 1971 for private mode fire applications. The model FSF104 Selectable Horn provides two different field selectable tones and a high/low output setting that can be accomplished with the use of mini jumpers located on the back of the unit. The FSF104 is clearly labeled with FIRE lettering and is polarized for connecting to supervised fire alarm circuits. The FSF is available in 24VDC only; however, the horn will operate with a regulated DC supply or a FWR (full wave rectified) power source. The FSF104 is listed for indoor use, utilizing the same configuration for both ceiling and wall mount, under the UL1971 standard. The model FSF105 Selectable Chime provides a continuous tone or temporal pattern tone when constant voltage from a Fire Alarm Control Panel is applied. Each tone has two dba levels (high or low) to choose from by repositioning a jumper located on the back of the unit. The FSF105 can be connected either independently or in unison. Using the FSF206 Synchronization module, the Temporal pattern of the FSF105 can be synchronized if two or more audible appliances are desired. The model FSF105 Selectable Chime is listed for indoor use when installed in a wall or ceiling mount configuration. 5 yr 5W A R R A N T Y Operating Operating Operating Decibels Model Voltage Temperature 10 FSF104 24VDC 32 F to 120 F 7-47 ma 88 0 C to 49 C FSF105 24VDC 32 F to 120 F ma 70 0 C to 49 C

26 SELECTABLE FIRE ALARM (FSF104/FSF105) 5 /12.7 cm 5 /12.7 cm 1.53 /3.9 cm SPECIFICATIONS Color: Red Net Weight: 1.0 lbs kg Height: 5.0" 12.7 cm Width: 5.0" 12.7 cm Depth: 1.53" 3.9 cm HOW TO ORDER Specify model number FSF104 Horn, Multi-tone FSF105 Chime, Multi-tone Please refer to Model Number Index FSF104/FSF105 beginning on page Federal Signal Dr., University Park, IL Tel: Fax:

27 FEDERAL SIGNAL CORPORATION Indoor/Outdoor Fire Alarm Bell Model FSF106 INDOOR/OUTDOOR AUDIBLE SIGNAL Indoor/outdoor motor driven design Universal mounting to 4" square back box High sound output with low current draw Supervisable polarized design Operates on Filtered DC or FWR input voltage Screw terminals allow quick field wiring UL Listed for Fire Protective Services ULC Listed and CSFM Approved The Federal Signal Model FSF106 Fire Alarm Bell is an audible signal meant to provide local notification when a Fire Alarm Control Panel has been activated. Normally mounted above doors, on walls or permanently fixed to other structures, the FSF106 produces a rapid ringing tone pattern that is clearly recognizable when heard. The FSF106 utilizes a specially designed gong that gives a loud mechanical resonant tone. This bell design incorporates a micro-motor with a built-in varistor suppression element to reduce RFI and EMI interference found in today s highly integrated microprocessor driven control panels. Installation is straight forward. The FSF106 micro-motor assembly acts as a universal mounting plate, allowing installation to various wall surfaces and back boxes. The convenient terminal design speeds installation and reduces troubleshooting time, while the 6 gong is removable to allow assembly to and removal from the mounting surface. The FSF106 Fire Alarm Bell is painted Red to enhance appearance and maximize durability. Operating Operating Model Voltage Temperature Current FSF106 24VDC -31 F to 150 F amps -35 C to 66 C 5 yr 5W A R R A N T Y

28 INDOOR/OUTDOOR FIRE ALARM BELL (FSF106) 5.91 /150 mm 4.72 /120 mm 2.52 /64 mm SPECIFICATIONS Color: Red Sound Output: 83dBa Net Weight: 1.0 lbs kg Height: 5.91" mm Width: 5.91" mm Depth: 2.52" 64.0 mm HOW TO ORDER Specify model and voltage Please refer to Model Number Index FSF106 beginning on page Federal Signal Dr., University Park, IL Tel: Fax:

29 FEDERAL SIGNAL CORPORATION Duct Smoke Detector and Sampling Tube Models FSF107 and FSF108 PHOTOELECTRIC DUCT SMOKE DETECTION Available in 24 VAC/VDC and 120/240 VAC Air velocity rating from 100 to 4,000 feet per minute Equipped with two DPDT Form C relay contacts Mounts to either round or rectangular ducts 1 to 12 Built in reset button Transparent cover for convenient visual inspection The Federal Signal Model FSF107 4-Wire Smoke Detector is a photoelectric device capable of sensing smoke in air velocities from 100 to 4,000 feet per minute. This Low-Flow technology enables duct smoke detection throughout a broad range of airflow environments. Many difficult to solve HVAC applications occur in low air-flow duct applications where reliable smoke detection is critical. Two form C relay contacts provide reliable performance for the management of fans, blowers, and air conditioning systems. These devices can then be configured to prevent the spread of toxic smoke and fire gasses through a protected area. The FSF107 has been designed for simplified installation and easy maintenance. The modular construction allows for easy cleaning and uncomplicated field replacement of the power and sensor boards. The patented cover missing feature insures the cover is securely tightened following routine cleaning and maintenance. The patented interconnectability feature allows multiple FSF107 s to communicate with each other. In the event smoke is detected, the FSF107 will signal the remaining detectors to initiate their relays for smoke control. A five foot metal sampling tube is an optional accessory available under part number FSF108. Optional FSF108 sampling tube available UL recognized field replacement power and sensor boards UL268A Listed Operating Storage Model Voltage Temperature Temperature FSF107 24VAC/VDC 32 F to 131 F -22 F to 158 F 120/240VAC 0 C to 55 C -30 C to 70 C 5 yr 5W A R R A N T Y

30 DUCT SMOKE DETECTOR & SAMPLING TUBE (FSF107/FSF108) /37 cm 2.75 /7 cm 5 /1.52 m 5.5 /14 cm SPECIFICATIONS Max Standby Current: Max Alarm Current: at 24VDC at 24VAC at 120VAC at 240 VAC at 24VDC at 24VAC at 120VAC at 240VAC 15mA 35mA RMS 25mA RMS 15mA RMS 70mA 125mA RMS 35mA RMS 25mA RMS Contact Ratings: Alarm initiation contacts(spst) 30VAC/VDC Alarm auxiliary contacts(dpdt) 30VDC 250VAC Trouble contacts(spdt) 30VDC(resistive) Weight FSF107: 3.75 lbs. 1.7 kg Weight FSF108: 2.4 lbs kg Height: 2.75" 7.0 cm Width: cm Length: 14.38" 37.0 cm HOW TO ORDER Please refer to Model Number Index FSF107/FSF108 beginning on page Federal Signal Dr., University Park, IL Tel: Fax:

31 FEDERAL SIGNAL CORPORATION 2-Wire Photoelectric and Ionization Smoke Detectors Models FSF109 and FSF110SB PHOTOELECTRIC AND IONIZATION DETECTORS Local LED indication Model FSF109 has a removable detector cover for easy cleaning Requires UL Listed fire alarm control panels Universal mounting plate adapts to 4" square, single-gang, doublegang, or octagon back box Built in test switch Drift compensation and smoothing algorithms Model FSF110SB detects both visible and invisible smoke Low stand-by current Smoke detectors are a key part of any comprehensive fire alarm system as smoke may be present before flames. The Federal Signal model FSF109 Two-wire Photoelectric Smoke Detector and the FSF110SB Two-wire Ionization Smoke Detector are designed to provide notification at a UL Listed Fire Alarm Control Panel when smoke is present. Each unit provides a localized indication of stand-by and alarm conditions via a built in status LED The FSF109 Smoke Detector includes a removable cover for easy cleaning, a local switch for field testing, and a sealed design to minimize dust and insect intrusion. The Federal Signal model FSF109 Photoelectric detector is designed to detect smoke through its effects on light. This makes the device highly effective at detecting a smoldering fire long before it bursts into flames. Drift compensation and smoothing algorithms are standard to minimize false activation. The model FSF110SB Ionization Smoke Detector reacts to the changes in ionized particles, making it better at detecting a flaming or quickly consuming fire. With this design, the FSF110SB can detect smoke not visible to the naked eye. Both detectors are capable of detecting a fast-flaming fire, however for complete protection and notification, a heat detector, duct detector and an audible/visual alarm may be purchased separately. Each FSF Smoke Detector incorporates a slim profile, designed to be unobtrusive and minimize potential overhead obstruction. The included mounting plate is designed to fit a 4" square junction box, 3 1 /4" octagon box or plaster ring and adapts easily to uneven mounting surfaces. 5 yr 5W A R R A N T Y Operating Max Standby Max Alarm Model Voltage Temperature Current Current FSF VDC 32 F to 100 F 24VDC 24VDC 0 C to 37.8 C FSF110SB VDC -4 F to 140 F 24VDC 24VDC -20 C to 60 C

32 SMOKE DETECTORS (FSF109/FSF110SB) FSF /5 cm 6 /116.1 cm 5.3 /13.46 cm 1.96 /5 cm FSF110SB SPECIFICATIONS FSF109 Net Weight: 0.4 lbs kg Diameter: 5.3" cm Depth: 2.0" 5.0 cm HOW TO ORDER Specify model and voltage Please refer to Model Number Index FSF109/FSF110SB beginning on page 381 FSF110 Net Weight: 0.34 lbs kg Diameter: 6.0" 16.1 cm Depth: 1.96" 5.0 cm 2645 Federal Signal Dr., University Park, IL Tel: Fax:

33 FEDERAL SIGNAL CORPORATION Selectable Strobe and Horn Combination Models FSF200ST and FSF201ST STROBE/HORN COMBO FOR FIRE ALARM USE Designed to meet or exceed NFPA requirements Universal mounting plate adapts to 4" square, single-gang, doublegang or octagon back box Low profile design Supervisable polarized design Field selectable audible tones and Candela rating Can be synchronized using FSF206 Synchronization Module CSFM and MEA Approved UL Listed for wall mount ULC Listed Federal Signal Models FSF200ST and FSF201ST Combination Selectable Strobe and Horns are designed to provide both visual and local audible indication indoors when activated by a Fire Alarm Control Panel. Each model can be synchronized to work simultaneously with other units and each complies with NFPA requirements and UL categories 464 and 1971 for private mode fire applications. The model FSF200ST and FSF201ST Combination Selectable Strobe and Horn provides two different field selectable Strobe outputs and two different audible tones. Each model contains a front mounted tamper-proof switch that allows the user to select the amount of strobe light flash energy required for the application. The FSF200ST is capable of either 15 or 30 Candela and the FSF201ST is capable of 75 or 110 Candela. There are also two different tone settings, with each tone having a high or low output setting. A 3000 Hz tone or simulated electromechanical tone can be selected by configuring mini jumpers located on the back of the unit. A temporal or non-temporal Tone Pattern and a high or low dba output are selected in the same manner. Each model is molded in red and clearly labeled with white FIRE lettering, while polarization is standard for connecting to supervised fire alarm circuits. The FSF200ST and the FSF201ST are available in 24VDC only, however, each will operate with a regulated DC supply or a FWR (full wave rectified) power source. Both the FSF200ST and the FSF201ST are listed for wall mounted indoor use, under the UL1971 standard. The FSF200ST and FSF201ST can be connected either independently or in unison. Using the FSF206 Synchronization module, both audible and visual patterns can be synchronized if two or more audible appliances are desired. Each FSF Combination Strobe & Horn incorporates a slim profile, designed to be unobtrusive and minimize potential obstruction. The included mounting plate is designed to fit a 4" square junction box, 3 1 /4" octagon box or plaster ring and it adapts easily to uneven mounting surfaces. 5 yr 5W A R R A N T Y Operating Max Operating Max Light Max Sound Model Voltage Temperature Current Output Output FSF200ST 16-33VDC 32 F to 120 F VDC Regulated 30 Candela 84dBa 0 C to 49 C VDC FWR* FSF201ST 16-33VDC 32 F to 120 F VDC Regulated 110 Candela 84dBa 0 C to 49 C VDC FWR* *FWR = Full wave rectified

34 SELECTABLE STROBE AND HORN COMBINATION (FSF200ST/FSF201ST) 5 /12.7 cm 5 /12.7 cm Strobe 2.25 /5.72 cm SPECIFICATIONS Weight (FSF200ST): 1.0 lbs kg Weight (FSF201ST): 1.0 lbs kg Height: 5.0" 12.7 cm Width: 5.0" 12.7 cm Depth: cm HOW TO ORDER Specify model and voltage Please refer to Model Number Index FSF200ST/FSF201ST beginning on page Federal Signal Dr., University Park, IL Tel: Fax:

35 FEDERAL SIGNAL CORPORATION Selectable Strobe Light for Fire Alarm Use Models FSF204ST and FSF205ST SLIM PROFILE VISUAL INDOOR INDICATION Designed to meet or exceed NFPA requirements and ADA requirements Universal mounting plate adapts to 4" square, single-gang, doublegang, or octagon back box Low profile design Supervisable polarized design Field selectable candela rating Can be synchronized using FSF206 Synchronization Module CSFM and MEA Approved UL Listed for wall mount ULC Listed Federal Signal Models FSF204ST and FSF205ST Selectable Strobe Lights are designed to provide visual indication indoors when activated by a Fire Alarm Control Panel. Each model can be synchronized to work simultaneously with other units and each complies with NFPA requirements and UL categories 464 and 1971 for private mode fire applications. The model FSF204ST and FSF205ST Selectable Strobe Light provides two different field selectable Strobe outputs. Each model contains a front mounted tamper-proof switch that allows the user to select the amount of strobe light flash energy required for the application. The FSF204ST is capable of either 15 or 30 Candela and the FSF205ST is capable of 75 or 110 Candela. Each model is molded in red and clearly labeled with white FIRE lettering, while polarization is standard for connecting to supervised fire alarm circuits. The FSF204ST and the FSF205ST are available in 24VDC only, but each will operate with a regulated DC supply or a FWR (full-wave rectified) power source. Both the FSF204ST and the FSF205ST are listed for wall mounted indoor use, under the UL1971 standard. The FSF204ST and FSF205ST can be connected either independently or in unison. Using the FSF206 Synchronization module, the visual pattern can be synchronized if two or more audible appliances are desired. Each FSF Selectable Strobe light incorporates a slim profile, designed to be unobtrusive and minimize potential obstruction. The included mounting plate is designed to fit a 4" square junction box, 3 1 /4" octagon box or plaster ring and it adapts easily to uneven mounting surfaces. 5 yr 5W A R R A N T Y Operating Flash Rate/ Max Operating Max Light Model Voltage Temperature Minute Current Output FSF204ST 16-33VDC 32 F to 120 F 60 24VDC Regulated 30 Candela 0 C to 49 C 24VDC FWR* FSF205ST 16-33VDC 32 F to 120 F 60 24VDC Regulated 110 Candela 0 C to 49 C 24VDC FWR* * FWR = Full wave rectified

36 SELECTABLE STROBE LIGHT FOR FIRE ALARM USE (FSF204ST/FSF205ST) 5 /12.7 cm 5 /12.7 cm Strobe 2.25 /5.72 cm SPECIFICATIONS Weight (FSF204ST): 1.0 lbs kg Weight (FSF205ST): 1.0 lbs kg Height: 5.0" 12.7 cm Width: 5.0" 12.7 cm Depth: cm HOW TO ORDER Specify model and voltage Please refer to Model Number Index FSF204ST/FSF205ST beginning on page Federal Signal Dr., University Park, IL Tel: Fax:

37 FEDERAL SIGNAL CORPORATION Synchronization Module for Fire Alarm Use Model FSF206 PROVIDES SIMULTANEOUS OPERATION OF STROBES AND SOUNDERS Designed to meet or exceed NFPA requirements and ADA requirements Daisy chain up to 20 modules Mounts to 4" square back box The Federal Signal Model FSF206 Synchronization Module is designed to provide simultaneous operation of select fire alarm strobes and sounders (FSF104, FSF105, FSF200ST, FSF201ST, FSF204ST, and FSF205ST) when initiated by a Fire Alarm Control Panel. Strobe light flashes and temporal pattern of certain horns can be synchronized, along with the ability to silence the horn while maintaining the strobe flashes. The FSF206 has the capability of connecting two Class B circuits or one Class A circuit and is rated for 3 Amps per circuit. The FSF206 can be interconnected so that more than two alarm zones can be synchronized. The maximum number of interconnected modules is twenty. All inputs are polarized for compatibility with standard reverse polarity supervision of circuit wiring by a Fire Alarm Control Panel. Polarized design CSFM and MEA Approved UL and ULC Listed Operating Max Operating Max Load Model Voltage Temperature Current On Loop FSF VDC 32 F to 120 F 24VDC Regulated 3 amps 0 C to 49 C 24VDC FWR* *FWR = Full wave rectified 5 yr 5W A R R A N T Y

38 SYNCHRONIZATION MODULE (FSF206) 4.33 /11 cm 4.33 /11 cm 0.2 /0.5 cm SPECIFICATIONS Weight: 1.0 lbs kg Height: 4.33" 11 cm Width: 4.33" 11 cm Depth: cm HOW TO ORDER Specify model and voltage Please refer to Model Number Index FSF206 beginning on page Federal Signal Dr., University Park, IL Tel: Fax:

39 FEDERAL SIGNAL CORPORATION Explosion-Proof Fire Alarm Pull Station Model MPEX TWO-STEP OPERATION PREVENTS ACCIDENTAL ACTIVATION Available in 120VAC Highly visible red enclosure Lift cover and pull down ring to activate Approved for Class I, Division 1 explosion-proof applications UL and ULC Listed CSFM Approved CSA Certified The Model MPEX Explosion-Proof Pull Station is designed for harsh environments. The unit is rated for Class I, Division 1, Groups C & D; Class II, Division 1, Groups E, F and G; and Class III. MPEX is rated NEMA 7 for Groups C & D and NEMA 9 for Groups E, F and G. The Model MPEX Explosion-Proof Pull Station is designed for hazardous locations where flammable gases, vapors, combustible dusts or easily ignitable fibers are present. The unique swing-up front cover exposes a pull-down ring which activates the alarm; this two-step process prevents accidental activation. The MPEX is reset by depressing the shaft and returning the plate to its original position. Contacts on the unit are rated 120VAC, 60Hz at six amps continuous. The enclosure is made of copper-free cast aluminum alloy. Installation is made easy via the feed through 3 /4" conduit openings found on either end of the MPEX. It is painted bright red for high visibility and has clearly marked operating instructions on the face plate. 5 yr 5W A R R A N T Y