User s Manual YTA610 and YTA710 NEPSI Certification
|
|
- Annabel Bates
- 5 years ago
- Views:
Transcription
1 User s Manual YTA60 and YTA70 NEPSI Certification [Option code: /NS, /NS5 and /NF] st Edition
2 . INTRODUCTION Thank you for purchasing the YTA60 and YTA70 Temperature transmitters. This manual contains important note and handling cautions for the YTA Temperature Transmitters with NEPSI certification, option code /NS, NS5 and /NF. Refer to the following user s manuals for standard specifications, functions, handling cautions, and operations, etc. Table. List of User s Manuals Title YTA60 and YTA70 Temperature Transmitters (Hardware) YTA60 and YTA70 Temperature Transmitter (HART Protocol) YTA60 and YTA70 Temperature Transmitter (Fieldbus Communication). NEPSI Certification () Technical Data a) NEPSI Intrinsically Safe Type Caution for NEPSI Intrinsically safe type Document No. IM 0C50G0-0EN IM 0C50T0-0EN IM 0C50T0-0EN Note. Certification information -0mA type Model YTA60 and YTA70 with /NS Certificate No.: GYJ6.X Applicable Standard: GB86.-00, GB86.-00, GB Type of Protection and Marking code: Ex ia IIC T/T5 Ga Temperature Class: T, T5 Ambient Temperature: 0 to 70 C for T, 0 to 50 C for T5 Enclosure: IP66/IP67 in accordance with only IEC 6059 Electrical Data [Supply/Output circuit] Ii = 00 ma Pi =.0 W Ci = nf [Sensor circuit] Po = 5 mw Co = 0 μf st Edition: Dec. 06 (YK) All Rights Reserved, Copyright 06, Yokogawa Electric Corporation Dielectric strength: 500 V a.c.r.m.s., min [, -, C,,,,, 5] to Earth terminal [, -, C] to [,,,, 5] Fieldbus type Model YTA60 and YTA70 with /NS5 Certificate No.: GYJ6.X Applicable Standard: GB86.-00, GB86.-00, GB Type of Protection and Marking Code: Ex ia IIC T Ga Temperature Class: T Ambient Temperature : 55 to 60 C for T Enclosure: IP66/IP67 in accordance with only IEC 6059 FISCO field Device Electrical parameters [Supply/output circuit] Ii = 00 ma Pi =. W Ci =. nf [Sensor input circuit] Po = 5 mw Co = 0 μf Dielectric strength: 500 V a.c.r.m.s., min [, -,,,,, 5] to Earth terminal [, -] to [,,,, 5] Note. Special condition for safe use WARNING When the enclosure of the Temperature Transmitter is made of aluminum alloy, if it is mounted in an area where the use of EPL Ga equipment is required, it must be installed such that, even in the event of rare incidents, an ignition source due to impact and/or friction sparks is excluded Precautions shall be taken to minimize the risk from electrostatic discharge of the painted parts. The dielectric strength of 500V r.m.s between the intrinsically safe circuit and the enclosure of the Temperature Transmitter is limited, only by the removable surge absorber F90AR. When the surge absorber is used, the earthing facility should be in accordance with Clause.. of GB
3 WARNING: ELECTROSTATIC CHARGE MAY CAUSE AN EXPLOSION HAZARD. AVOID ANY ACTIONS THAT CAUSE THE GENERATION OF ELECTROSTATIC CHARGE, SUCH AS RUBBING WITH A DRY CLOTH ON COATING FACE OF THE PRODUCT. Note. Control Drawing -0mA Non- Temperature Transmitter Intrinsically Safe apparatus or Simple apparatus Sensor Input 5 Supply/Output C Associated Apparatus Sensor lnput: Po = 5 mw Co = 0 μf Model YTAxxx - J or - D Supply/Output: Ii = 00 ma Pi =.0 W Ci = nf F0.ai Fieldbus Non- Terminator Terminator Associated Apparatus Field Device Field Device Linear source of FISCO power supply Intrinsically Safe apparatus or Simple apparatus Model YTAxxx - F or - G Temperature Transmitter Sensor Input Supply/Output 5 Sensor lnput: Po = 5 mw Co = 0 μf Model YTAxxx - F or - G Supply/Output: Ii = 00 ma Pi =. W Ci =. nf FISCO field device F0.ai
4 Note. Conditions for safe use Cable entry should be applied when installation in hazardous location and redundant holes for cable entry should be closed by blanking elements. The IP code should be IP66/IP67. This product should be used in explosive gas atmospheres together with associated apparatus, follow the instruction manual of this product and the associated apparatus when connecting the wiring. Connect the wiring terminals correctly. It is forbidden to change the configuration except for the removable surge arrester, to ensure the equipment s explosion protection performance. When installation, use and maintenance of Temperature Transmitter, observe following standards GB Explosive atmospheres - Part : Equipment repair, overhaul and reclamation GB Electrical apparatus for explosive gas atmospheres Part 5: Electrical installations in hazardous area (other than mines) GB Electrical apparatus for explosive gas atmospheres Part 6: Inspection and maintenance of electrical installation (other than mines) GB Explosive atmospheres - Part 8: Intrinsically safe system GB Code for construction and acceptance of electric equipment on fire and explosion hazard electrical equipment installation engineering. b) NEPSI Flameproof Type Caution for NEPSI Flameproof Type Note. Model YTA60/NF and YTA70/NF Applicable Standard: GB86.-00, GB86.-00, GB76.-0, GB Certificate No.: GYJ6.96X Type of Protection and Marking Code: Ex d IIC T5/T6 Gb, Ex td A IP66/IP67 T70 C/T90 C Temperature Class: T5, T6 Ambient Temperature for Gas Atmospheres: 0 to 80 C for T5, 0 to 75 C for T6 Ambient Temperature for Dust Atmospheres: 0 to 65 C for T70 C, 0 to 80 C for T90 C Enclosure: IP66/IP67 Note. Electrical Data Supply voltage : V dc max. ( to 0 ma type) : V dc max. (Fieldbus type) Output signal : to 0 ma : ma dc max. (Fieldbus type) Note. Installation All wiring shall comply with local installation Requirements. Note. Operation Keep strictly the WARNING on the label on the transmitter. WARNING: AFTER DE- ENERGIZING, DELAY 0 MINUTES BEFORE OPENING. WHEN THE AMBIENT TEMP. 70 C, USE THE HEAT- RESISTING CABLE & CABLE GLANDS 90 C. POTENTIAL ELECTROSTATIC CHARGING HAZARD. -SEEUSER S MANUAL BEFORE USE. Take care not to generate mechanical spark when access to the instrument and peripheral devices in hazardous location. Note 5. Conditions for safe use The external earth connection facility shall be connected reliably. M0X.5 or /-NPT thread type cable entry, adapters and/or blanking elements, certified by notified body with type of protection Ex d IIC Gb in accordance with GB and GB86.-00, should be applied when installation in explosive gas atmosphere. M0X.5 or /-NPT thread type cable entry, adapters and/or blanking elements, certified by notified body with type of protection Ex td A in accordance with GB76.-0 and GB76.5-0, should be applied when installation in combustible dust atmosphere. At least IP6X should be guaranteed after the assembly. Forbid end user to change the configuration to ensure the equipment s explosion protection performance.
5 When installation, use and maintenance of Temperature Transmitter, observe following standards GB86.-0 Explosive atmospheres - Part : Equipment repair, overhaul and reclamation GB Electrical apparatus for explosive gas atmospheres Part 5: Electrical installations in hazardous area (other than mines) GB Electrical apparatus for explosive gas atmospheres Part6: Inspection and maintenance of electrical installation (other than mines) GB Code for construction and acceptance of electric equipment on fire and explosion hazard electrical equipment installation engineering GB Safety regulations for dust explosion prevention and protection GB Electrical apparatus for use in the presence of combustible dust-part : Selection and installation Revision Record Dec. 06 st edition New Publication. Note 6. Special condition for safe use WARNING The suffix X placed after the certificate number indicates that this product is subject to special conditions for safe use: The values of the flamepaths are different from the standard values given in GB Repair of the equipment is only allowed when done by the manufacturer or authorized representative. When used in hazardous location, electrostatic discharge should be avoided. () Electrical connection The type of electrical connection is stamped near the electrical connection port according to the following marking. Screw Size ISO M0.5 female ANSI / NPT female Marking M N Location of the marking F0.ai
YTA Series Temperature Transmitters [Style: S3] EN :2006, -11:2007, -26:2007. Supply circuit: Ui=30 V, Ii=165 ma,
User s Manual YTA Series Temperature Transmitters [Style: S3] Manual Change No. 10-008 Please use the attached sheets in the following manuals when the product is with /KU2 option and EN60000 Series based
More informationUser s Manual. AXF Series Magnetic Flowmeter Installation Manual ATEX and IECEx Explosion Proof Type IM 01E20A01-11EN IM 01E20A01-11EN.
User s Manual AXF Series Magnetic Flowmeter Installation Manual ATEX and IECEx Explosion Proof Type Contents 1. ATEX Documentation 2. Explosion Proof Type Instrument 2.1 ATEX...2 2.2 IECEx...7 1 2 Integral
More informationUser s Manual. EJA Series Differential Pressure and Pressure Transmitters Manual Change No Yokogawa Electric Corporation
User s Manual EJA Series Differential Pressure and Pressure Transmitters Manual Change No. 12-004 For the models EJA and EJA-A series with option code /KF21, /KU21, /KU22 or /KN26, please use this manual
More informationUser s Manual. EJA Series Differential Pressure and Pressure Transmitters Installation Manual. 1. Introduction. 2. Handling Cautions. 3.
User s Manual EJA Series Differential Pressure and Pressure Transmitters Installation Manual 1. Introduction 1.1 For Safe Use of Product...2 1.2 Warranty...3 1.3 ATEX Documentation...4 2. Handling Cautions
More informationOPTIBAR DP 7060 Supplementary Instructions
OPTIBAR DP 7060 Supplementary Instructions Differential pressure transmitter Category ATEX II 1/2G, 2G Ex db ia IIC T6...T1 Ga/Gb, Gb IECEx Ex db ia IIC T6...T1 Ga/Gb, Gb Housing Aluminium: Single chamber,
More informationEXPLOSION PROTECTION
EXPLOSION PROTECTION CERTIFICATE OF CONFORMITY This is to certify that the product Cert NO.GYJ15.1225X Miniature Resistance Thermometer manufactured by WIKA Alexander Wiegand SE & Co.KG (Address:Aiexander-Wiegand-Stra6e
More informationOPTIWAVE X500 Supplementary Instructions
OPTIWAVE X500 Supplementary Instructions OPTIWAVE 3500 C OPTIWAVE 6500 C OPTIWAVE 7500 C Supplementary Instructions for ATEX applications KROHNE CONTENTS OPTIWAVE X500 1 General safety information 4 1.1
More informationRosemount 8800D Series Vortex Flowmeter. Quick Start Guide , Rev FE October 2018
Rosemount 8800D Series Vortex Flowmeter 00825-0100-4004, Rev FE 1 About this guide This guide provides basic guidelines for the Rosemount 8800D Series Vortex Flowmeter. It does not provide instructions
More informationSafety instructions VEGADIF DF65.GX*****H/Z/P/F***** IECEx BVS
Safety instructions VEGADIF DF65.GX*****H/Z/P/F***** IECEx BVS 10.0008 Ex td A20, A20/21, A20/22, A21 IP66 T 0044 37675 Contents 1 Area of applicability 3 2 General information 3 2.1 Zone 20 instruments
More informationAdditional Operating Instructions SITRANS F. Vortex flowmeters. SITRANS FX330 Ex-d.
Additional Operating Instructions SITRANS F Vortex flowmeters Ex-d Edition 09/208 CONTENTS Safety instructions 3. General notes... 3.2 EU conformity... 3.3 Approval according to the IECEx scheme... 3.4
More informationRosemount 8600 Series Vortex Flowmeter. Quick Start Guide , Rev EB April 2018
Rosemount 8600 Series Vortex Flowmeter 00825-0100-4860, Rev EB April 2018 April 2018 1 About this guide This guide provides basic guidelines for the Rosemount 8600D Series Vortex Flowmeter. It does not
More informationCertificate of Compliance
FF0002 Certificate of Compliance Certificate: 2792948 Issued to: Siemens Canada Limited 1954 Technology Drive Peterborough, ON K9J 7B1 Canada Attention: Mr. Lee Rogers The products listed below are eligible
More informationOperating Instructions Edition 02/2007
Operating Instructions Edition 02/2007 Temperature Transmitter 7NG3214 with PROFIBUS PA 7NG3215 with FOUNDATION Fieldbus sitrans Introduction 1 General safety notes 2 SITRANS T Temperature transmitter
More informationRosemount 248 Temperature Transmitter
Product Data Sheet November 2013 00813-0100-4825, Rev KA Rosemount 248 Temperature Transmitter Basic temperature transmitter offers a reliable solution for temperature monitoring points transmitter design
More informationAnnubar Flowmeter Series
Reference Manual Appendix B Approvals Annubar Flowmeter Series Hazardous Locations Installations.................. page B-1 Rosemount 3051SFA Product Certifications.......... page B-1 Rosemount 3095MFA
More informationEXPLOSION PROTECTION CERTIFICATE OF CONFORMITY Certificate No.: GYJ X
EXPLOSION PROTECTION CERTIFICATE OF CONFORMITY Certificate No.: GYJ15.1137X Manufacturer: Product: Model Specification: Anti-explosion Mark: Topworx Inc. (Address: 3300 Fern Valley Road, Louisville, Kentucky
More informationEXPLOSION PROTECTION CERTIFICATE OF CONFORMITY Certificate No.: GYJ X
EXPLOSION PROTECTION CERTIFICATE OF CONFORMITY Certificate No.: GYJ15.1138X Manufacturer: Product: Model Specification: Anti-explosion Mark: Topworx Inc. (Address: 3300 Fern Valley Road, Louisville, Kentucky
More informationAdditional Operating Instructions SITRANS F. Vortex flowmeters. SITRANS FX330 Ex-i.
Additional Operating Instructions SITRANS F Vortex flowmeters Ex-i Edition 09/2018 CONTENTS 1 Safety instructions 3 1.1 General notes... 3 1.2 EU conformity... 3 1.3 Approval according to the IECEx scheme...
More informationCertificate of Compliance
FF0 001 Certificate of Compliance Certificate: 70116284 (LR 064969_0_00) Issued to: Mine Safety Appliances Company North American Division 1000 Cranberry Woods Dr Cranberry Township, Pennsylvania 16066-5296
More informationRADAR LEVEL GAUGE SPECIAL SAFETY INSTRUCTION
Special Safety Instruction en RADAR LEVEL GAUGE SPECIAL SAFETY INSTRUCTION Contents TankRadar Pro European ATEX Directive Information............................... 2 ATEX marking and Ex Certification
More informationSITRANS T. SITRANS T Explosion protected temperature sensor. General information. Marking of the degree of protection. Range of uses.
General information 1 Marking of the degree of protection 2 SITRANS T SITRANS T Explosion protected temperature sensor Operating Instructions Range of uses 3 Installation 4 Assembly and disassembly 5 Commissioning
More informationRosemount 644 Temperature Transmitter
Quick Start Guide 00825-0200-4728, Rev GB Rosemount 644 Temperature Transmitter with 4 20 ma HART Protocol (Revision 5 and 7) Note Before installing the transmitter, confirm the correct device driver is
More informationEU DECLARATION OF CONFORMITY
The Low Voltage Directive (LVD) 2014/35/EU and Electromagnetic Compatibility (EMC) Directive 2014/30/EU. Capacitive level sensor DLS 27N(T) Capacitive level sensor type DLS 27N(T) is designed to bistable
More informationOfficine Meccaniche M.A.M. series for command, control, signaling and/or automation. DOCUMENT IS-EJB-A-14 rev. 0
Officine Meccaniche M.A.M. Apparecchiature Antideflagranti DOCUMENT IS-EJB-A-14 rev. 0 Instructions Flameproof enclosures EJB../W series for command, control, signaling and/or automation Emission date:
More informationCertificate of Compliance
FF0 001 Certificate of Compliance Certificate: 70116279 (LR 025993_0_000) Issued to: General Monitors, Incorporated 26776 Simpatica Circle Lake Forest, California 92630 USA Attention: Larry Vlagea The
More informationAdditional Operating Instructions SITRANS F. Vortex flowmeters. SITRANS FX330 Ex-nA.
Additional Operating Instructions SITRANS F Vortex flowmeters Ex-nA Edition 08/207 CONTENTS Safety instructions 3. General notes... 3.2 EU conformity... 3.3 Approval according to the IECEx scheme... 3.4
More informationCertificate of Compliance
Certificate of Compliance Certificate: 70000097 Project: 70125347 Issued to: Thermo Engineering S.r.l Via Giuseppina, 19 26030 Malagnino (CR) Italy Attention: Mr. BOZZETTI The products listed below are
More informationOilSET Installation and Operating Instructions. Oil Separator Alarm Device with SET/DM3AL sensor
Labkotec UK Ltd Adminicle House 1 Lumb Lane Audenshaw Manchester M34 5WH GREAT BRITAIN Tel: 0844 3350 477 Fax: 0161 4281 179 E-mail: info@labkotec.co.uk 10.8.2012 Internet: www.labkotec.co.uk 1/13 OilSET-1000
More informationTechnical Data. General specifications. Rated operating distance s n 5 mm
0102 Model Number Features 5 mm non-flush Usable up to SIL 2 acc. to IEC 61508 Technical Data specifications Switching function Normally closed (NC) Output type NAMUR Rated operating distance s n 5 mm
More informationIECEx Certificate. INTERNATIONAL ELECTROTECHNICAL COMMISSION IEC Certification Scheme for Explosive Atmospheres
INTERNATIONAL ELECTROTECHNICAL COMMISSION IEC Certification Scheme for Explosive Atmospheres for rules and details of the IECEx Scheme visit www.iecex.com Certificate No.: Certificate history: Status:
More informationInductive slot sensor
0102 Model Number Features 2 mm slot width Technical Data specifications Switching function Normally closed (NC) Output type NAMUR Slot width 2 mm Depth of immersion (lateral) 5... 7 mm, typ. 6 mm Output
More informationQuick Start Guide , Rev CB May Rosemount 3144P Temperature Transmitters with FOUNDATION fieldbus Protocol
Quick Start Guide 00825-0100-4834, Rev CB Rosemount 3144P Temperature Transmitters with FOUNDATION fieldbus Protocol Quick Start Guide NOTICE NOTICE This guide provides basic guidelines for the Rosemount
More informationSET Installation and Operating Instructions. Level switch for one sensor
Labkotec Oy Myllyhaantie 6 FI-33960 PIRKKALA FINLAND Tel.: +358 29 006 260 Fax: +358 29 006 1260 7.11.2013 Internet: www.labkotec.fi 1/14 SET-1000 Level switch for one sensor Copyright 2013 Labkotec Oy
More informationRosemount 3144P Rosemount 3144P Temperature Transmitter
Temperature Transmitter Sensor Drift Alert and Hot Backup features improve measurement reliability while the Transmitter-Sensor Matching feature improves temperature measurement accuracy Statistical Process
More informationIECEx Certificate of Conformity
IECEx Certificate of Conformity INTERNATIONAL ELECTROTECHNICAL COMMISSION IEC Certification Scheme for Explosive Atmospheres for rules and details of the IECEx Scheme visit www.iecex.com Certificate IECEx
More informationRosemount 848T High Density Temperature Measurement Family
Product Data Sheet July 2017 00813-0100-4697, Rev PA Rosemount 848T High Density Temperature Measurement Family Innovative temperature measurement for high density applications that provide installation
More informationINSTRUCTION MANUAL (ATEX / IECEx)
INSTRUCTION MANUAL (ATEX / IECEx) BExS110D and BExS110D-R Sounder For use in Flammable Gas and Dust Atmospheres BExS110D BExS110D-R 1) Warnings DO NOT OPEN WHEN AN EXPLOSIVE ATMOSPHERE IS PRESENT DO NOT
More informationINSTRUCTION MANUAL IS-mB1 Minialite Intrinsically Safe Round LED Beacon
INSTRUCTION MANUAL Minialite Intrinsically Safe Round LED This instruction sheet describes installations which conform to EN60079:Part14:2008 Electrical Installation in Hazardous Areas. When designing
More informationIECEx TEST REPORT IEC Explosive atmospheres Part 0: Equipment General requirements
ExTR Reference Number...: ExTR Free Reference Number...: 223531 Compiled by + signature (ExTL)...: Reviewed by + signature (ExTL)...: NO/NEM/ExTR12.0018/00 Stig André Norheim Arne Hortman Date of issue...:
More information4) Intrinsic Safety Certification
INSTRUCTION MANUAL Minialert Intrinsically Safe Round Combined Unit Section Volume Control Tone Generator S2 S3 Tone Selection Switches Fig 1 Simplified block diagram The combined unit is CE marked for
More informationRosemount 2051 Pressure Transmitter with 4-20 ma HART and 1-5 Vdc HART Low Power Protocol
Quick Installation Guide August 2009 Rosemount 2051 Rosemount 2051 Pressure Transmitter with 4-20 ma HART and 1-5 Vdc HART Low Power Protocol Start Step 1: Mount the Transmitter Step 2: Consider Housing
More informationCertificate of Compliance
Certificate of Compliance Certificate: 70033893 (166720) Issued to: WIKA Alexander Wiegand SE & Co. KG Alexander-Wiegand-Str 30 Klingenberg, 63911 GERMANY Attention: Uwe Schmidt The products listed below
More informationVERSAFLOW VORTEX Supplementary instructions
VERSAFLOW VORTEX Supplementary instructions Vortex flowmeter Equipment category II 2G CONTENTS VERSAFLOW VORTEX 1 Safety instructions 3 1.1 General notes... 3 1.2 EC conformity... 3 1.3 Approval according
More informationATEX Explained A brief Introduction
The Trusted Source for Secure Identity Solutions ATEX Explained A brief Introduction January 19, 2016 ATEX Zones Zones 1 (gas) or 21 (dust) (area in which under normal operation a potentially explosive
More informationOilSET-1000 (12 VDC)
Labkotec Oy Myllyhaantie 6 FI-33960 PIRKKALA FINLAND Tel: +358 29 006 260 Fax: +358 29 006 1260 Internet: www.labkotec.fi 20.03.2009 1/11 OilSET-1000 (12 VDC) Oil Separator Alarm Device Copyright 2009
More informationGeneral Specifications
General Specifications GS 12A01A02-72E Model FLXA 21 2-Wire Analyzer PROFIBUS PA Communication General PROFIBUS is a vendor-independent and open fieldbus based on the international standard IEC61158 and
More informationRosemount 248 Temperature Transmitter
Product Data Sheet March 2017 00813-0100-4825, Rev LA Rosemount 248 Temperature Transmitter Basic temperature transmitter offers a reliable solution for temperature monitoring points. Standard transmitter
More informationSET-2000 Oil/Sludge 12 VDC
Labkotec Oy Myllyhaantie 6 FI-33960 PIRKKALA FINLAND Tel: + 358 29 006 260 Fax: + 358 29 006 1260 12.2.2015 Internet: www.labkotec.fi 1/14 SET-2000 Oil/Sludge 12 VDC Alarm Device for Oil Separators with
More informationRosemount 848T FOUNDATION Fieldbus High Density Temperature Transmitter
Quick Start Guide 00825-0100-4697, Rev SF Rosemount 848T FOUNDATION Fieldbus High Density Temperature Transmitter Device Revision 8 - Requires New DD/CFF Revision Quick Start Guide NOTICE This guide provides
More informationUser s Manual. YTA110, YTA310, YTA320, and YTA710 Temperature Transmitters. Manual Change No
User s Manual YTA110, YTA310, YTA320, and YTA710 Temperature Transmitters Manual Change No. 16-045 Please use this manual change for the manuals listed below. 1. Applicable manuals, revised item, revised
More informationINSTRUCTION MANUAL (ATEX)
INSTRUCTION MANUAL (ATEX) ISmA1M Minialarm Intrinsically Safe Round ISmA1M Volume Control Tone Generator S3 Tone Selection Switches Fig 1 Simplified block diagram The ISmA1M sounder is CE marked for compliance
More informationBrooks Models MT3809G and MT3810G Metal Tube Variable Area Flowmeters
Installation and Operation Manual Brooks Models MT3809G and MT3810G Metal Tube Variable Area Flowmeters Model MT3809G, FNPT Connections, General Purpose Stainless Steel Housing Model MT3809G, Flanged Connections,
More informationAdditional Information. Introduction. Temperature transmitter for all communications protocols. Redundancy thanks to two inputs. Measurement made easy
ABB MEASUREMENT & ANALYTICS COMMISSIONING INSTRUCTION TTF300 Field-mount temperature transmitter Temperature transmitter for all communications protocols. Redundancy thanks to two inputs. Measurement made
More informationQuick Start Guide , Rev HA January Rosemount 248 Temperature Transmitter
00825-0100-4825, Rev HA Rosemount 248 Temperature Transmitter NOTICE This guide provides basic guidelines for the Rosemount 248. It does not provide instructions for detailed configuration, diagnostics,
More informationRosemount 2090F Hygienic Pressure Transmitter
Rosemount 2090F Hygienic Pressure Transmitter Product Data Sheet December 2017 00813-0100-4698, Rev GA Conforms to 3-A Sanitary Standards Features CIP/SIP service for process temperatures up to 284 F (140
More informationRosemount 248 Temperature Transmitter
Product Data Sheet January 2018 00813-0100-4825, Rev LB Rosemount 248 Temperature Transmitter Basic temperature transmitter offers a reliable solution for temperature monitoring points. Standard transmitter
More informationSafety Instructions Omnigrad S TR/TC6x
XA01450T/09/EN/01.16 71340266 Products Solutions Services Safety Instructions Omnigrad S TR/TC6x RTD / TC Thermometer 1ExdIICT6...T4 X, DIP A21 T A 85 C/100 C/135 C Omnigrad S TR/TC6x XA01450T Omnigrad
More informationSchedule of Accreditation issued by United Kingdom Accreditation Service 2 Pine Trees, Chertsey Lane, Staines-upon-Thames, TW18 3HR, UK
2 Pine Trees, Chertsey Lane, Staines-upon-Thames, TW18 3HR, UK 17065:2012 to provide product conformity certification Newport Business Park New Port Road Ellesmere Port CH65 4LZ United Kingdom Contact:
More informationRosemount 248 Temperature Transmitter. Quick Start Guide , Rev. EA April 2013
Rosemount 248 Temperature Transmitter 00825-0100-4825, Rev. EA NOTICE This installation guide provides basic guidelines for the Rosemount 248 Wireless. It does not provide instructions for detailed configuration,
More informationRosemount 644H Temperature Transmitters
Quick Start Guide 00825-0100-4829, Rev DA Rosemount 644H Temperature Transmitters with FOUNDATION Fieldbus Quick Start Guide NOTICE This guide provides basic guidelines for the Rosemount 644. It does not
More informationAS/NZS :2009 Explosive atmospheres - Part 14: Electrical installations design, selection and erection
Skip to main content Skip to primary navigation Home Home About this portal Latest updates Menu Print Save Email Resource detail Citations AS/NZS 60079.14:2009 Explosive atmospheres - Part 14: Electrical
More informationOilSET Installation and Operating Instructions. Oil Separator Alarm Device
Labkotec Oy Myllyhaantie 6 FI-33960 PIRKKALA FINLAND Tel: +358 29 006 260 Fax: +358 29 006 1260 18.11.2010 Internet: www.labkotec.fi 1/10 OilSET-1000 Oil Separator Alarm Device Copyright 2010 Labkotec
More informationRosemount 3051 Pressure Transmitter
Quick Start Guide 00825-0100-4001, rev. JA Rosemount 3051 Pressure Transmitter with 4-20 ma HART and 1-5 Vdc Low Power Protocol Rosemount 3051CF Series Flowmeter Transmitter with 4-20 ma HART and 1-5 Vdc
More informationRosemount 3051S MultiVariable Transmitter Rosemount 3051SF Series Flowmeter MultiVariable Transmitter
Quick Start Guide 00825-0100-4803, Rev EF Rosemount 3051S MultiVariable Transmitter Rosemount 3051SF Series Flowmeter MultiVariable Transmitter Quick Start Guide NOTICE This guide provides basic guidelines
More informationRosemount 214C Sensor. Quick Start Guide , Rev AF August 2017
Rosemount 214C Sensor 00825-0400-2654, Rev AF NOTICE This guide provides basic guidelines for Rosemount 214C Sensor models. If the sensor was ordered assembled to a temperature thermowell or transmitter,
More informationModel 144H. Product Data Sheet , Rev DB February Content
Rosemount 144 PC-Programmable Temperature Transmitter Provides an installation-ready solution for temperature monitoring applications using Complete Point Solutions (CPS) Increases measurement accuracy
More informationRosemount 702 Wireless Discrete Transmitter
August 2009 Rosemount 702 Rosemount 702 Wireless Discrete Transmitter Start Step 1: Physical Installation Step 2: Verify Operation Step 3: Reference Information Product Certifications EC Declaration of
More informationREGULATIONS EUROPEAN ATEX DIRECTIVE. INTERNATIONAL SCHEME: IECEx AREAS CLASSIFICATION DEFINED BY DIRECTIVE 1999/92/EC
EUROPEAN ATEX DIRECTIVE > European Directive 2014/34/EU ATEX Directive 2014/34/EU is a "new approach" directive that applies to protective systems against explosions as well as all equipment used in or
More informationOPTIBAR P 1010/2010 C Supplementary instructions
OPTIBAR P 1010/2010 C Supplementary instructions Pressure transmitter Equipment category II 1G / Ga, II 1D / Da in protection type intrinsic safety Exi KROHNE CONTENTS OPTIBAR P 1010/2010 C 1 Safety instructions
More informationIECEx Certificate of Conformity
INTERNATIONAL ELECTROTECHNICAL COMMISSION IEC Certification Scheme for Explosive Atmospheres for rules and details of the IECEx Scheme visit www.iecex.com Certificate No. : Status: Date of Issue: Applicant:
More informationSafety instructions VEGABAR 81, 82, 83, 86, 87
C US Safety instructions VEGABAR 81, 82, 83, 86, 87 Dust ignition protection CSA 70015745 Document ID: 52267 Contents 1 Area of applicability... 3 2 General information... 3 3 Technical data... 4 4 Installation
More informationRosemount 752 Fieldbus Remote Indicator
Product Data Sheet Rosemount 752 Rosemount 752 Fieldbus Remote Indicator ROSEMOUNT 752 DELIVERS: Two-wire segment powered device Displays up to 8 values Link Master Capability Optional PID, Characterizer,
More informationfor CE 134 CCSAUS certificate Meggitt SA Route de Moncor 4 PO Box 1616 CH Fribourg Switzerland Title page EN
Title page CCSAUS certificate: EN 70034691 for EX Meggitt SA Route de Moncor 4 PO Box 1616 CH - 1701 Fribourg Switzerland CCSAUS certificate 70034691 www.meggittsensingsystems.com www.vibro-meter.com THIS
More informationATEX GUIDE. A short introduction to ATEX Terminology. Equipment for use in flammable atmospheres. Directive 94/9/EC
Quick Introduction to TÛV Denmark TÜV Denmark - is a part of the TÜV NORD Group a global Organisation f Certification and Inspection of: Quality Management Systems, Products, Processes and Qualification
More informationRosemount 3051S Series Pressure Transmitter and Rosemount 3051SF Series Flowmeter
Quick Start Guide 00825-0100-4801, Rev NA Rosemount 3051S Series Pressure Transmitter and Rosemount 3051SF Series Flowmeter with HART Protocol Quick Start Guide NOTICE This guide provides basic guidelines
More informationSET-2000 Oil/Sludge. Alarm Device for Oil Separators. Installation and Operating Instructions
SET-000 Oil/Sludge Alarm Device for Oil Separators Copyright 007 Labkotec Oy We reserve the right for changes without notice TABLE OF CONTENTS GENERAL... INSTALLATION... 4. SET-000 Oil/Sludge Control Unit...
More informationRosemount 2090F Hygienic Pressure Transmitter
Rosemount 2090F Hygienic Pressure Transmitter Product Data Sheet November 2016 00813-0100-4698, Rev FC Conforms to 3-A Sanitary Standards Features CIP/SIP service for process temperatures up to 284 F (140
More informationTechnical Data. Dimensions
0102 Model Number Features 8 mm non-flush Stainless steel housing Usable up to SIL2 acc. to IEC 61508 Technical Data specifications Switching element function NAMUR, NC Rated operating distance s n 8 mm
More informationInstallationsmanual GWSL1100/2100, GWML3100
GRAIN-WATCH SYSTEM Installationsmanual Grain Watch Sensor Cables GWSL1100/2100, GWML3100 Table of contents 1 1 1 3. Safety certification and features 3.1. Certification label information 3.2. Safety approvals
More informationIECEx Certificate of Conformity
INTERNATIONAL ELECTROTECHNICAL COMMISSION IEC Certification Scheme for Explosive Atmospheres for rules and details of the IECEx Scheme visit www.iecex.com issue No.:2 Status: Current Date of Issue: 2014-05-14
More information国家级仪器仪表防爆安全监督检验站 National Supervision and Inspection Centre for Explosion Protection and Safety of Instrumentation (GYJ ) (Attachment Ⅰ) Attachm
国家级仪器仪表防爆安全监督检验站 National Supervision and Inspection Centre for Explosion Protection and Safety of Instrumentation (GYJ14.1317) (Attachment Ⅰ) Attachment Ⅰ (Translation) Isolated safety barrier type KFa
More informationTechnical Data. General specifications Switching element function Rated operating distance s n 5 mm
0102 Model Number Features 5 mm non-flush Usable up to SIL2 acc. to IEC 61508 Technical Data specifications Switching element function NAMUR, NC Rated operating distance s n 5 mm Installation non-flush
More informationRosemount 2088 Absolute and Gage Pressure Transmitter
Product Data Sheet February 2015 00813-0100-4690, Rev PB Rosemount 2088 Absolute and Gage Pressure Transmitter Performance of 0.065% with High Accuracy option Lightweight, compact design for cost-effective
More informationRosemount 148 Temperature Transmitter. Quick Start Guide , Rev GA September 2016
Rosemount 148 Temperature Transmitter 00825-0100-4148, Rev GA NOTICE This guide provides basic guidelines for the Rosemount 148. It does not provide instructions for detailed configuration, diagnostics,
More informationSET-2000 Hi Level/Oil
Labkotec Oy Labkotie 1 FI-36240 KANGASALA FINLAND Tel: + 358 29 006 260 Fax: + 358 29 006 1260 13.03.2008 Internet: www.labkotec.fi Alarm Device for Oil Separators Copyright 2008 Labkotec Oy We reserve
More informationQuick Start Guide For the
A Leader in Level Measurement Quick Start Guide For the Universal IV Lite and Universal IV Pro Model Transmitters 2-Wire RF Admittance / Capacitance Level Measurement System with HART Protocol For Assistance
More informationIECEx Certificate of Conformity
Page 1 of 10 IECEx Certificate of Conformity INTERNATIONAL ELECTROTECHNICAL COMMISSION IEC Certification Scheme for Explosive Atmospheres for rules and details of the IECEx Scheme visit www.iecex.com Certificate
More informationRosemount 2051G Pressure Transmitter
Quick Start Guide 00825-0700-4101, Rev AB Rosemount 2051G Pressure Transmitter with 4 20 ma HART Protocol (Revision 5 and 7) Quick Start Guide NOTICE This guide provides basic guidelines for Rosemount
More informationCenturion Guided Radar HAWK CGR SERIES
Safety Instructions CGR (Cat 3GD) Centurion Guided Radar HAWK CGR SERIES ATEX Category 3GD Intrinsically Safe probe / Flameproof enclosure II 3G Ex ia/d IIC T6 T2 Gc II 3D Ex ia tb IIIC T85 C T255 C Dc
More informationIECEx Certificate of Conformity
INTERNATIONAL ELECTROTECHNICAL COMMISSION IEC Certification Scheme for Explosive Atmospheres for rules and details of the IECEx Scheme visit www.iecex.com issue No.:3 Status: Current Date of Issue: 2010-10-04
More informationRosemount 8800D Series Vortex Flowmeter
Quick Installation Guide Rosemount 8800D Rosemount 8800D Series Vortex Flowmeter Start Step 1: Mount the Flowmeter Step 2: Consider Housing Rotation Step 3: Set Jumpers and Switches Step 4: Connect Wiring
More informationMT3809G Series. Metal Tube Variable Area Flowmeters. Overview. Product Description. Variable Area
DS-VA-MT3809G-eng December, 2017 Data Sheet MT3809G Series MT3809G General Purpose Housing Variable Area Metal Tube Variable Area Flowmeters Overview Brooks MT3809 meter operation is based on the variable
More informationRosemount 3144P Temperature Transmitters with FOUNDATION Fieldbus Protocol. Quick Start Guide , Rev DA June 2016
Rosemount 3144P Temperature Transmitters with FOUNDATION Fieldbus Protocol 00825-0100-4834, Rev DA NOTICE This guide provides basic guidelines for Rosemount 3144P. It does not provide instructions for
More informationMT5000 Guided Wave Radar Level Transmitter. State-of-the-art loop powered, 4-20 ma output guided wave radar transmitter for liquid level applications
Safety manual SM/MT5000 series-en Rev. A MT5000 Guided Wave Radar Level Transmitter State-of-the-art loop powered, 4-20 ma output guided wave radar transmitter for liquid level applications Introduction
More informationRosemount 2051 Pressure Transmitter and Rosemount 2051CF Series Flowmeter
Quick Start Guide 00825-0400-4101, Rev AD Rosemount 2051 Pressure Transmitter and Rosemount 2051CF Series Flowmeter with PROFIBUS PA Protocol Quick Start Guide NOTICE This installation guide provides basic
More informationRosemount 644H Temperature Transmitters
Quick Start Guide 00825-0300-4728, Rev BA Rosemount 644H Temperature Transmitters with PROFIBUS PA Quick Start Guide NOTICE This guide provides basic guidelines for the Rosemount 644. It does not provide
More informationRosemount 3490 Series
Product Data Sheet July 2014 00813-0100-4841, Rev DA Rosemount 3490 Series 4 20 ma + HART Compatible Controller Field mounted controller with integral multi-function LCD and keypad Tough weatherproof wall
More informationAr-Mite TM Low Flow Armored Flowmeter
Data Sheet Brooks Ar-Mite TM MT 3750C Ar-Mite TM Low Flow Armored Flowmeter Ar-Mite TM Model MT 3750 Metal Tube Flowmeter Ar-Mite TM Model MT 3750 Metal Tube Flowmeter with Transmitter or Inductive Alarm
More informationTechnical Data. Dimensions
0102 Model Number Features Comfort series 50 mm non-flush Technical Data specifications Switching element function NAMUR, NC Rated operating distance s n 50 mm Installation non-flush Output polarity NAMUR
More informationE2S Datasheet v10a. The IS-mA1 is suitable for all intrinsically safe signalling applications including fire, security and process control.
E2S Datasheet 1.2.1 v10a ISmA1 ISminialarm The ISmA1 is a compact, 100dB(A) alarm sounder. Approvals include ATEX, IECEx and GOSTR for Zone 0 applications and FM approval for Class I Division 1 and Class
More information