Miniature Thermoelectric Cooler Controller MTCC-01 user's guide

Size: px

Start display at page:

Download "Miniature Thermoelectric Cooler Controller MTCC-01 user's guide"

Christal Lindsay Summers
5 years ago
Views:

1 Miniature Thermoelectric Cooler Controller MTCC-01 user's guide 1

2 Table of Contents 1. Warranty MTCC-01 overview MTCC-01 specification TE cooled detector temperature stabilization general information MTCC-01 operation Connectors Sample kit wiring MTCC-01 physical dimensions Getting started regards complete IR detection kit Unpacking Installation & connections Switching on procedure MTCC-01 other related information CE statement of conformity Electromagnetic interference Operating temperature Storage information Safety instructions Troubleshooting

3 1. Warranty VIGO System S.A. hereby represents and warrants all Products manufactured by VIGO and sold hereunder to be free from defects in workmanship or material during a period of twelve (12) months from the date of delivery save for products for which a special warranty is given. If any Product proves however to be defective in workmanship or material within the period herein provided VIGO System undertakes to the eclusion of any other remedy to repair or at its own option replace the defective Product or part thereof free of charge and otherwise on the same conditions as for the original Product or part without eten sion to original warranty time. Defective parts replaced in accordance with this clause shall be placed at the disposal of VIGO. VIGO also warrants the quality of all repair and service works performed by its employees to products sold by it. In case the repair or service works should appear inadequate or faulty and should this cause malfunction or nonfunctioning of the product to which the service was performed VIGO shall at its free option either repair or have repaired or replace the product in question. The working hours used by employees of VIGO for such repair or replacement shall be free of charge to the client. This service warranty shall be valid for a period of si (6) months from the date the service measures were completed. This warranty is however subject to following conditions: A substantiated written claim as to any alleged defects shall have been received by VIGO System within thirty (30) days after the defect or fault became known or occurred, and The allegedly defective Product or part shall, should VIGO so require, be sent to the works of VIGO or to such other place as VIGO may indicate in writing, freight and insurance prepaid, properly packed and labeled. This warranty does not however apply when the defect has been caused through normal wear and tear or accident; misuse or other unsuitable or unauthorized use of the Product or negligence or error in storing, maintaining or in handling the Product or any equipment thereof; wrong installation, assembly or failure to service the Product or otherwise follow VIGO's service instructions including any repairs or installation or assembly or service made by unauthorized personnel not approved by VIGO or replacements with parts not manufactured or supplied by VIGO; modifications or changes of the Product as well as any adding to it without VIGO's prior authorization; burned active element by irradiation above damage thresholds electrostatic discharges improper detector bias improper TE cooler bias (TE cooler damage or active element overheating). other factors dependent on the Customer or a third party. Notwithstanding the aforesaid VIGO System liability under this clause shall not apply to any defects arising out of materials, designs or instructions provided by the Customer. This warranty is epressly in lieu of and ecludes all other conditions, warranties and liabilities, epressed or implied, whether under law, statute or otherwise, including without limitation any implied warranties of merchantability or fitness for a particular purpose and all other obligations and liabilities of VIGO or its representatives with respect to any defect or deficiency applicable to or resulting directly or indirectly from the Products supplied hereunder, which obligations and liabilities are hereby epressly canceled and waived. VIGO's liability shall under no circumstances eceed the invoice price of any Product for which a warranty claim is made, nor shall VIGO in any circumstances be liable for lost profits or other consequential loss whether direct or indirect or for special damage. RMA Request Instructions: No Product may be returned without first contacting VIGO for a Return Material Authorization ('RMA') number. Please obtain a RMA number at claim@vigo.com.pl before returning any item. When requesting a RMA number, please state your order number, the product you wish to return and the reason for return. We will only accept returns which have a RMA number. Authorized returns are to be shipped according to received instruction from VIGO in appropriate shipping bo. An unauthorized return, i.e. one for which an RMA number has not been issued and authorized returns however, shipped with incorrect customs documents - will not be accepted. Please print the RMA number clearly on the return label to avoid any delay in processing. Please send package to: VIGO System S.A. 129/133 Poznanska St., PL Ozarow Mazowiecki Poland 3

4 2. MTCC-01 overview The MTCC-01 (Miniature Thermoelectric Cooler Controller) is the module designed for supplying the thermoelectric cooler (being a part of the cooled IR detector) and providing the temperature stabilization process. The MTCC-01 is suited to work with 2- and 3- stage cooled detector (2TE, 3TE). Due to the compact size, MTCC-01 is especially convenient to use in OEM applications. Features Compact size Low cost Easily configurable by the user High stability and precision Adjustable temperature Low power consumption 2.1. MTCC-01 specification Parameter Temperature stability Unit K Typical value Conditions, remarks 1) ± 0.01 Settling time of the set detector temperature s stage TEC, Tdet=230K 3-stage TEC, Tdet=205K Power supply voltage VSUP V 2.6 to to 5.5 for 2-stage TEC for 3-stage TEC Maimum TEC output current ITEC A ) for 2-stage TEC for 3-stage TEC Maimum TEC output voltage VTEC V 3.6 Dimensions mm Weight g 35 1) Electrical = 20 OC, Vdd = 5 V 2) Depends on TEC version width depth height 4

5 2.2. TE cooled detector temperature stabilization general information Every cooled detector, besides containing IR sensitive structure, is equipped with: TEC (ThermoElectric Cooler), Thermistor, Depending on the requirements, like responsivity, noise level, and therefore the final temperature, detectors fabricated by VIGO contain 2-, 3- or 4-staged TE cooler. The lowest achievable temperature depends also on ambi ent temperature and the heat dissipated by the detector due to the detector biasing. Considering all the factors and preparing measurements under conditions comparable with those in final application, detectors are described and the final temperature is defined. The thermistor being inside the detector package gives the feedback about the IR sensor temperature and allows the controller to perform the temperature control process. The thermistor is a component common for every type of the IR sensors, which makes the temperature measurement simple and repetitive for each detector. Having the detector parameters measured, the MTCC-01 controller parameters (ma current, depending on the cooler) and final temperature are set, and the system is ready to work. The MTCC-01 module contains low noise and precise analog path, PID controller block, and the power stage for Peltier element driving. It also has diode indicating the actual state of the controller (getting the temperature down / ready to work). Temperature controller basing on the PID algorithm allows the system to quickly achieve the final temperature, keeping it long term stable with small fluctuations and can also adapt to varying environment conditions. The MTCC-01 is a linear controller, so it doesn't introduce disturbances to the IR detection system and does not affect its performance. 5

6 2.3. MTCC-01 operation Selecting the MTCC-01 parameters Before turning the IR detecting system on, the MTCC-01 controller has to be configured. TEC type (2- or 3stage) and the final temperature is set by shifting the jumpers to the proper positions. Some jumper positions activate the on board potentiometer and allow the user to adjust the final temperature precisely. Potentiometer for temperature adjustment Configuration jumpers UNIT Function stage TEC, ITEC MAX = 1.2 A 3-stage TEC, ITEC MAX = 0.45 A Ma. TEC current, no temperature control TDET = 230 K TDET = 220 K TDET = 240 K TDET = 220 to 240 K, adjustable TDET = 240 to 250 K, adjustable TDET = 232 to 245 K, adjustable TDET = 245 to 255 K, adjustable 6

LED indicators MTCC-01 controller has two LED diodes indicating the state of the module. RED diode (marked as POWER) is shining if the controller supply (VSUP) is properly connected.

2.4. Connectors The picture below shows the pin configuration of the module.

7 LED indicators MTCC-01 controller has two LED diodes indicating the state of the module. RED diode (marked as POWER) is shining if the controller supply (VSUP) is properly connected. GREEN diode (marked as LOCK) is shining if the detector temperature achieves the set value. After turning on the power supply the GREEN LED is off by maimum 300 seconds depending on the detector type Connectors The picture below shows the pin configuration of the module. Supply connector Preamplifier connector AMP 16 Pin Symbol Function AMP 24 Pin Symbol 1 +VDD TEC controller power supply 1 -VSUP Power supply output (-) 2 TGND TEC controller power supply 2 TH2 Thermistor input 3 +VSUP Power supply input (+) 3 4 GND Power ground 4 -TEC TEC supply output (-) 5 +FAN FAN power supply input (+) 5 GND Power ground 6 -VSUP Power supply input ( ) 6 TH1 Thermistor input 7 +VSUP Power supply output (+) 8 +TEC TEC supply output (-) +FAN FAN power supply output (+) 7

2.5. Sample kit wiring 1 3 4 2 The sample IR detection kit

the picture: SIPXC) 3) AMP 24 AMP 24 cable 4) AMP 16 power cable

8 2.5. Sample kit wiring The sample IR detection kit consists of: 1) MTCC-01 controller, 2) IR detection module (in the picture: SIPXC) 3) AMP 24 AMP 24 cable 4) AMP 16 power cable 2.6. MTCC-01 physical dimensions Dimensions are given in millimeters. 8

9 3. Getting started regards complete IR detection kit 3.1. Unpacking Before unpacking, verify if there are no visible damages of the package. Report them to the manufacturer or the distributor Installation & connections Mount the IR module in the measurement setup, Connect all elements with cables provided in the package, Make sure that all the elements are properly connected Switching on procedure Do not switch on the IR module power supply until ALL elements of the IR detection kit are correctly connected with the proper cables, Switch on the thermoelectric cooler controller and wait until detector operating temperature is reached and stabilized. Ready state will be indicated by the LOCK green LED light, Before starting the measurements make sure the load resistance is valid. IR detector module output should be terminated by 50Ω or 1MΩ resistance depending on the bandwidth and is given in the test data provided on the module, Do not manipulate any connectors on the active IR kit this may introduce additional noises to the system or can cause severe damages due to electrostatic discharges. 9

10 4. MTCC-01 other related information 4.1. CE statement of conformity VIGO System declares that IR detection kit is fully compliant with: EU Low Voltage Directives: 73/23/EEC, 93/68/EEC EU Electromagnetic Compatibility Directives: 89/336/EEC, 91/263/EEC, 92/31/EEC, 93/68/EEC 4.2. Electromagnetic interference To avoid the electromagnetic interferences (EMI), please do not put any electromagnetic source close to the IR module. That may cause interference to the input of the preamplifier and disturb the useful signal in the IR track 4.3. Operating temperature Detector parameters are guaranteed for the environment temperature not eceeding 35 OC Storage information To ensure reliable operation and long lifetime of detector, the following conditions should be fulfilled: Storage temperature: -10ºC + 50ºC and 10% to 90% humidity, Avoid eposing to direct sunlight and strong UV/VIS light as this may result in degradation of a detector performance, Avoid electrostatic discharges (ESD). 10

11 5. Safety instructions To ensure safe and failure-free operation of the MTCC-01 controller, comply with the following precautions: Before connecting the power supply to the mains, make sure if it is compatible with the mains voltage and fre quency. Do not use the controller if the temperature and the air humidity etends the values valid for the MTCC-01 controller. Use the proper cables to connect elements of the kit, dedicated for specified device only. Never cut or shorten any cable, it may cause damage to your device. Use the cables delivered by VIGO. In case of OEM systems, make sure the the cables match the specifica tion of the controller. Turn off the power supply before plugging / unplugging cables. Avoid static discharges. MTCC-01 controller is an OEM type, so it is not equipped with the case. Provide the proper shielding and avoid touching the module while working. MTCC-01 module doesn't require forced cooling, although keep the radiator not covered and allow the air to flow the module. Important note! If you are setting up own system supplied by the the custom power supply, please make sure, the voltage/current matches to the values of the TEC and the IR detector. 11

12 6. Troubleshooting Typical reasons of malfunction the controller and the possible solutions are collected in the following table. Symptom SUPPLY diode is not shining LOCK diode is never turned on, or turns of after some time LOCK diode is blinking Possible reason Typical solution Controller is not connected to the supply Connect the controller and the power supply together Power supply is not connected to the mains Connect the power supply to the mains Controller or power supply is broken Contact with the distributor or the manufacturer The controller is not connected with the IR detector Properly connect the controller and the detector TEC efficiency is too small Increase the final detector temperature by reconfiguring switches or using potentiometer Environment temperature is too high Keep the environment temperature within the limits. Controller or IR detector is broken Contact with the distributor or the manufacturer IR radiation flu is too strong Reduce the IR radiation level IR detector position is unstable, or it is eposed to the vibrations Properly mount the IR detector and keep it mechanically stable Controller or IR detector is broken Contact with the distributor or the manufacturer 12

Miniature Thermoelectric Cooler Controller MTCC-01 user's guide

Miniature Thermoelectric Cooler Controller MTCC-01 user's guide 1 Table of Contents 1. Warranty... 3 2. MTCC-01-xxx overview... 4 2.1. MTCC-01-xxx specification... 4 2.2. TE cooled detector temperature