ND4000 Manual Marine Hydraulics
|
|
- Carmel Barber
- 5 years ago
- Views:
Transcription
1 ND4000 Manual Marine Hydraulics Version 1.0 May 2012 Page 1
2 Contents Line Counter Components... 3 Proximity Sensors... 3 Connecting the Proximity Sensors to the SSCD... 3 Fuse... 3 USB... 4 Computer Display... 4 ND4000 Line Counter Software... 4 Running the software... 4 Operating the ND4000 Line Counter... 4 Display Settings... 4 Navigating the Display... 5 Using the ZERO Button... 6 Setting the Stbd In Alarm... 7 Choosing the Alarm Adding your own Alarm Sound Setup Company Setup Vessel and Encoder Setting Winch Parameters Using a slider Display Options Toggle Display Hue Adjust Accuracy Page 2
3 Line Counter Components The ND4000 line counter consists of 4 Proximity Sensors (2 per winch), a Sensor Signal Conditioning Box (SSCD), Power Supply Module (PSM), Universal Serial Bus (USB) cable and Computer Display. Proximity Sensors at the winch detect Spool Rotation. The sensor pulses are fed into the SSCD where they are decoded into a serial count that is fed into a Computer via a USB cable. The ND4000 Line Counter software translates the pulse counts into line length, Spool RPM and direction. Proximity Sensors 2 wire Analog output inductive sensors with a 4-20 ma output signal Connecting the Proximity Sensors to the SSCD 2 wire shielded cable must be used to connect the sensors to the SSCD. The push-in connection terminals on the SSCD accept AWG wire. For the same length, 18 gauge wire has one tenth the resistance of 26 gauge wire. As push-in terminals are used, support the cables adequately to prevent pull out due to cable weight. Terminals are arranged as 2 groups of 4: one group for each winch. Connections to the SSCD are as shown in the following figure (Which is attached to the SSCD): Red to Sensor + Tin the wire ends before inserting into the Push-in terminal blocks. To release push the red release lever and pull out the wire. Fuse The Fuse Holder is accessible from the opposite of the terminal block side of the SSCD. The fuse type is 5mm x 20mm. The fuse should be rated at approximately.5 A. Page 3
4 USB Connect a USB cable (supplied) between the SSCD and the Computer. The USB cable has a standard Type A USB connector on one end and a Mini Type B USB connector on the SSCD end. Computer Display The ND4000 is shipped with a Windows tablet PC. Power Connector On Off button USB ND4000 Line Counter Software Software comes pre-installed. USB Running the software The USB cable must be plugged in. You can register more than one SSCD on the same Display Computer. Operating the ND4000 Line Counter All information is this section refers to the ND4000 supplied with a Display Computer Display Settings The display will scale full screen to any monitor resolution. Use the default text size, otherwise there may be a problem with text cut off. Page 4
5 Navigating the Display The following figure outlines the display. The various components are described. Page 5
6 Line Speed in Selected Units per second Line Out Length in Selected Units Selected Units Current Spool RPM Spool revolutions from Start of haul out. ZERO Set Using the ZERO Button The ZERO Button will set the current reading to 0. The button can be pushed multiple times. When Line is hauled back beyond 0, the display will show negative numbers. The zero point is not retained between shut down and power on of the Line Counter. If line is cut, use the Cut Line feature to recalibrate the winch. The alarm settings are based on the display value from 0. Page 6
7 Setting the Stbd In Alarm Click on the alarm setting (15.2 Meters). The In alarm display area will be highlighted with a box. The Alarm set point slider and small adjustment buttons will be activated. Alarm Display Area Set point slider Smal l adjustment Button Page 7
8 Adjust Alarm Set point Slider and or small adjustment buttons to new Set Point. Page 8
9 Click on In Alarm Set button In Alarm Set Button The other alarms are set in a similar way. Page 9
10 Choosing the Alarm A number of sounds are included as alarm sounds. Pick the alarm of choice from the drop down list. Page 10
11 Adding your own Alarm Sound You can add your own custom alarm (say,a recording your wife offering words of encouragement) by adding a wav file to the sounds folder in the install folder of the application. Something under 5 seconds long is preferable. Page 11
12 Setup Company Setup the winch on first run by entering the Company Name. Make Sure to get it right the first time because it can t be changed once entered. Select Ok Add a company name select Save then Ok Page 12
13 Setup Vessel and Encoder Then Add a Vessel Page 13
14 Setting Winch Parameters After Adding a Vessel Set the Winch Parameters Page 14
15 You MUST select the vessel before setting the parameter otherwise they will not be saved on form exit. All units are inches including the cable diameter. The top layer is measured in wraps. The diagram at left references the spool parameters. Sliders can be used or the number can be typed into the box. Note: the Display Computer has a touch screen so that a virtual keyboard is used. Slide for variable Using a slider increment There are three regions for adjusting a slider: Click for small increment Click for Large Increment Display Options A number of display options are accessible under the Tools menu. Toggle Display: This will show or hide the RPM and Line speed details at the top of the window. Enhance Precision: this will toggle the decimal point on or off and disable or enable rounding. Page 15
16 Hue: The sub menu items will change the back color of the screen to compensate for light conditions. The custom Option will bring up a standard windows color dialog. Adjust Accuracy: this option will bring up the adjustment dialog. This dialog is semi transparent and can be dragged anywhere on the screen. Page 16
17 Adjust the sliders for a true reading. The winch display will be scaled by the ratio of the adjusted value to the sensed value. Note: The winch accuracy is most affected by the top layer settings and accuracy improves as the level wind improves. This feature is intended to adjust the accuracy at a specific line out value and may not be accurate for lesser or greater distances spooled. Use the Set button to save the adjusted value. The settings can be cleared using the Clear Button. Page 17
M3092 Programmer. User s Manual. M3096B-33 E Copyright 2017 SELCO
User s Manual Copyright 2017 SELCO SELCO Betonvej 11 - DK-4000 Roskilde Denmark Phone: 45 7026 1122 - Fax: 45 7026 2522 e-mail: selco@selco.com www.selco.com Table of contents 1 INTRODUCTION...4 2 SOFTWARE
More informationUSER S GUIDE. AXIS Cross Line Detection
USER S GUIDE AXIS Cross Line Detection User s Guide Rev. 1.00 Copyright Axis Communications AB, 2009 November 2009 Part no. 36687 AXIS Cross Line Detection AXIS Cross Line Detection is a trip-wire application
More informationBC-4000 Bilge Monitor/Controller Installation Manual
SMART SWITCH TECHNOLOGIES BC-4000 Bilge Monitor/Controller Installation Manual Table of Contents Introduction 1 System Overview 1 System Overview (cont.) 2 Wiring Block Diagram 3 System Layout 4 Wiring
More informationAnalog Room Pressure Monitor RPC Series
Description The Room Pressure Monitor is used to measure differential pressure in the range of 0.125 to 1"wc or 30 to 250 Pa. It combines precision high sensitivity silicon sensing capabilities and the
More informationSoftware Version 2.01 LEVEL MONITOR MODEL 220
Software Version 2.01 LEVEL MONITOR MODEL 220 19 April 2000 CONTENTS 1. Introduction 1 1.1 Model Number Designation 2 1.2 Intrinsic Safety Considerations 3 2. Specification 4 3. Operation 6 3.1 Display
More informationUSER MANUAL DexTempTM 1000 Temperature Monitor (P/N: IR-1001) DexTempTM 1000 USB Non-Contact Temperature Monitor. User Manual.
USER MANUAL DexTempTM 1000 Temperature Monitor (P/N: IR-1001) DexTempTM 1000 USB Non-Contact Temperature Monitor User Manual 8690 Rev B Update: 10/24/2013 1 Table of Contents 1 Introduction.. 3 2 Host
More informationTV2 Room Pressure Monitor Quick Start Guide
TV2 Room Pressure Monitor Quick Start Guide 1. The Care and Use guide for your TV2 Room Pressure Monitor can be downloaded here: www.e2di.com/usersguides.html Please print out the Users Guide. Although
More informationSirius Technologies, Inc.
Model#: ST501 CO2/Temp/RH Indoor Air Quality Meter Users Manual Page 1 TABLE OF CONTENTS FEATURES & SPECIFICATIONS... 3 WHAT S IN THE BOX... 7 START UP AND GENERAL OPERATION... 8 Recording and Datalogging...
More informationStratomaster Smart Single
Stratomaster Smart Single EMS-503 Fully integrated Engine Monitoring System for the Rotax 503 DCDI and similar two-stroke engines such as available from Hirth, 2SI and others. The EMS-503 unit is a 2.25
More informationWeatherLink for Alarm Output Addendum
WeatherLink for Alarm Output Addendum Introduction This Streaming Data Logger is designed to provide an electrical interface between a Vantage Pro or Vantage Pro2 weather station console or Weather Envoy
More informationModSync Sequencing System Installation & Operation Manual. For use with Fulton Steam Boilers.
ModSync Sequencing System Installation & Operation Manual For use with Fulton Steam Boilers. Revision 3.0 8/21/2008 - 2 - Table of Contents Introduction Page 4 Features Page 4 Sequence of Operation Page
More informationCT398 Heaterstat TM Temperature Controller. Technical User Guide
CT398 Heaterstat TM Temperature Controller Technical User Guide CT398 HeaterStat Controller Contents CT398 HeaterStat Controller... 2 Contents... 2 Document Overview... 2 For More Information... 2 Introduction...
More informationOption M16.x Configurable I/O extension cards, four multi-inputs (4-20 ma/0-5 V/Pt100) Description of option Functional description
MULTI-LINE 2 DESCRIPTION OF OPTION Option M16.x Configurable I/O extension cards, four multi-inputs (4-20 ma/0-5 V/Pt100) Description of option DEIF A/S Frisenborgvej 33 DK-7800 Skive Tel.: +45 9614 9614
More informationInstalling ProSeries 2005
Installing ProSeries 2005 The following instructions will walk you through Installing and Launching ProSeries 2005. Before you begin your installation, it is very important to make note of the following
More informationCELLTROL II BIOREACTOR CONTROL SYSTEM OPERATIONS MANUAL
Operation Manual Celltrol II Bioreactor Control System Page 1 of 33 Table of Contents 1) Introduction... 3 1.1) Scope of Document... 3 1.2) Control System Overview... 3 1.3) Introduction to Celltrol II...
More informationTroubleshooting Thermo Scientific LevelPRO Gauges
Troubleshooting Thermo Scientific LevelPRO Gauges Key Words Scintillation detector Current board Relay output Communications Level indication Purpose A chapter in the user guide for the Thermo Scientific
More informationSierra Model 951 Digital Flo-Box. Instruction Manual Part Number IM-951 Revision A 09-05
Sierra Model 951 Digital Flo-Box Instruction Manual Part Number IM-951 Revision A 09-05 5 Harris Court, Building L Monterey, CA 93940 (831) 373-0200 (800) 866-0200 Fax (831) 373-4402 www.sierrainstruments.com
More informationMark 25 Ultrapure Water Conductivity Analyzer
Martek Instruments, Inc. Mark 25 Ultrapure Water Conductivity Analyzer Instruction Manual WARRANTY POLICY Unless otherwise stated, MARTEK INSTRUMENTS, INC. warrants this equipment to be free from defects
More informationDI220 Using the Optional Docking Station The maintenance and operating functions of the Micro IV can be automated with the Micro IV Docking Station.
DI220 Using the Optional Docking Station The maintenance and operating functions of the Micro IV can be automated with the Micro IV Docking Station. The following steps outline the correct sequence to
More informationPowerLogic ION Setup Meter Configuration Software Configuration Guide
PowerLogic ION Setup Meter Configuration Software Configuration Guide 70002-0293-03 12/2010 Conventions Used in this Manual This section describes the symbols and terminology used in this guide. Symbols
More informationSecurity Management System - Configuring Video Analytics
Introduction This document describes the steps for configuring the Video Analytics (VA) module available in the Security Management System software. Security Management System video analytics module is
More informationModule Features are-configurable, no module jumpers to set
December 2011 PACSystems* RX3i Isolated Thermocouple Input Module, 6 Channels, IC695ALG306 Isolated Thermocouple Input Module, 12 Channels, IC695ALG312 Isolated Thermocouple Input module IC695ALG306 provides
More informationFigure 1. Proper Method of Holding the ToolStick. Figure 2. Improper Method of Holding the ToolStick
CAN OBD READER REFERENCE DESIGN KIT USER GUIDE 1. Standard ToolStick Handling Recommendations The ToolStick Base Adapter and daughter cards are distributed without any protective plastics. To prevent damage
More informationRF SCOUT PLUS INSTRUCTION MANUAL. Dielectric, LLC 22 Tower Rd. Raymond, ME Phone: January 2015, Rev B 1
RF SCOUT PLUS INSTRUCTION MANUAL Dielectric, LLC 22 Tower Rd. Raymond, ME 04071 Phone: 800.341.9678 www.dielectric.com 21 January 2015, Rev B 1 WARNING Powering RF sensors above +30dBm (1W) will cause
More informationPlanning Elevator Relay Groups Programming Millenium for Windows Software
Installation Booklet: Elevator Control Unit (ECU) Introduction The Elevator Control Unit (ECU) is an option in the Millenium for Windows systems. Once you add an elevator in the software, each elevator
More informationTV2 Clean Room Monitor
TV2 Clean Room Monitor 1. The Care and Use guide for your TV2 Clean Room Monitor can be downloaded here: www.e2di.com/usersguides.html Please print out the Users Guide. Although you should use the Users
More informationHOBO U14 Data Logger User Manual
HOBO U14 Data Logger User Manual The U family of data loggers offers reliability and convenient monitoring for applications that require higher accuracy, better resolution, more memory, or USB connectivity
More informationTITLE RS20i Atmos & DTS:X Decoder Card (H693) Setup
NUMER 1 of 12 Introduction The RS20i with the H693 card installed and software update V1.05.00 or above is capable of the following Dolby and DTS decoder and post processing technologies: Dolby Atmos Dolby
More informationProcidia iware AlarmWorX32. AlarmWorX32 Viewer January 2010
Procidia iware AlarmWorX32 AlarmWorX32 Viewer Siemens Protection AG 2008. notice All / Copyright rights reserved. notice Introduction / Contents Procidia iware is an operator interface software designed
More informationInterior Design Tutorial
Controlling the Display of Objects Chapter 4: Interior Design Tutorial The Interior Design Tutorial picks up where the House Design Tutorial left off. The basic structure of the plan is complete, but the
More informationALPTEC Power factor controller
ALPTEC Power factor controller I - CONNECTIONS CONTROL II - MANUAL KEYPAD SET-UP III OPERATING MODE IV - ALARMS I - CONNECTIONS CONTROL At the first power up, the ALPTEC display views --- which means no
More informationE N G L I S H FIRE ALARM ASPIRATION SENSING TECHNOLOGY QUICK INSTALLATION GUIDE STAND-ALONE FAAST LT MODELS FL0111E FL0112E FL0122E. 367 mm.
E N G L I S H FIRE ALARM ASPIRATION SENSING TECHNOLOGY QUICK INSTALLATION GUIDE STAND-ALONE FAAST LT MODELS FL0E FL0E FL0E mm mm 0 mm DESCRIPTION The LT FL0 Series is part of the Fire Alarm Aspiration
More informationPump-Down Controller MODEL 4052
Pump-Down Controller 4-20mA Input/Scalable Output Seal Fail Monitoring Duplex Pump Alternation Hand-Off-Auto Controls Dual Run-time Meters RS-485/Modbus Communications DESCRIPTION The Model 4052 Pump-Down
More informationUser Guide. Shaft Speed 6 6-Channel Shaft Speed Monitor. Calibration and Operation Software Reference UDJ701-5
Electro-Magnetic Compatibility (EMC) This product complies with Council Directive 89/336/EEC when installed and used in accordance with the relevant instructions. Service and Technical Support PLEASE CONTACT
More informationInterior Design Tutorial
Interior Design Tutorial The Interior Design Tutorial picks up where the Roof Tutorial left off. The basic structure of the plan is complete, but the plan still needs lights, outlets, and fixtures to be
More informationDryer Controller M720
User Manual Dryer Controller M720 Hardware version 2.00 Software version 2.00 Manual M720 Dryer controller Page 1 of 60 Document history Preliminary version: - Created in April, 2009 Hardware Version 2.00,
More informationHERCULES 6 GRAPHICS SYSTEM
HERCULES 6 GRAPHICS SYSTEM USER MANUAL Protec Fire Detection PLC, Protec House, Churchill Way, Nelson, Lancashire, BB9 6RT. Telephone: +44 (0) 1282 717171 Fax: +44 (0) 1282 717273 Web: www.protec.co.uk
More informationUser Manual. Digi-Sense TC9500 Advanced Multiparameter Temperature Controller with Thermocouple, Thermistor, and RTD Inputs
User Manual Digi-Sense TC9500 Advanced Multiparameter Temperature Controller with Thermocouple, Thermistor, and RTD Inputs Models 89800-03 and 89800-04 THE STANDARD IN PRECISION MEASUREMENT Table of Contents
More informationGeneral The Dryer Programmer for Windows Computers
Published Manual Number: MQYDSB01 Specified Date: 20131120 As-of Date: 20131120 Access Date: 20131120 Depth: Detail Custom: n/a Applicability: YDS Language Code: ENG01, Purpose: publication, Format: 1colA
More informationCONsOlIDATOR 4 & 8. MulTI- C h ANNEl CONTROllERs. ConsoliDator 4 Model PD940 ConsoliDator 4 Features. ConsoliDator 8 Features.
CONsOlIDATOR 4 & 8 MulTI- C h ANNEl CONTROllERs ConsoliDator 4 Model PD940 ConsoliDator 4 Features Four 4-20 Four 4-20 Outputs ConsoliDator 8 Features Eight 4-20 Two 4-20 Outputs Common Features Four Pulse
More informationProduct Manual SZ1145
Product Manual SZ114 General Purpose Monitor Communicating Controls Description The SZ114 is a microprocessor-based monitoring and alarm interface designed to monitor up to four 1000 Ω platinum temperature
More informationMillennium Xtra. Millennium ATMA setup and configuration guide. May Millennium Group, Inc.
Millennium Xtra Millennium ATMA setup and configuration guide May 16 2017 Millennium Group, Inc. 16 Tech Circle Natick, MA 01760 P: 508-655-1340 F: 508-651-2902 Millennium ATMA setup and configuration
More informationCAN bus-based I/O module, CIO relays Mounting Terminals and wiring Commissioning, using the utility software
INSTALLATION AND COMMISSIONING GUIDE CAN bus-based I/O module, CIO 208 8 relays Mounting Terminals and wiring Commissioning, using the utility software DEIF A/S Frisenborgvej 33 DK-7800 Skive Tel.: +45
More informationPACSystems* RX3i. Thermocouple Input Module, 12 Channels, IC695ALG412. GFK-2578B October 2011
October 2011 PACSystems* RX3i Thermocouple Input Module, 12 Channels, IC695ALG412 The PACSystems * Thermocouple Input module IC695ALG412 provides twelve isolated differential thermocouple input channels.
More informationLOUP II DRILL MONITOR OPERATION MANUAL. SOFTWARE v45
LOUP II DRILL MONITOR OPERATION MANUAL SOFTWARE v45 Service and Technical Support Contact: Loup Electronics Inc. Address: 2960 N. 38th Street Lincoln, NE 68504 Phone: 877-489-LOUP(5687) 402-464-7131 Fax:
More informationIntelligent Video Analysis
Intelligent Video Analysis 1. Intelligent Video Analysis... 2 2. Unattended Object Detection... 6 3. Missing Object Detection... 7 4. Smoke and Fire detection... 8 5. Movement Direction Detection... 9
More informationTerex Operation Manual
Terex Operation Manual Table of Contents Outline of Operation... 3 System Components... 3 Power-Up Self-Test... 5 Home Display... 5 The Configuration Display... 6 Home Button... 7 Man Button... 7 POL Button...
More informationUser Manual. Dryer Controller M720
User Manual Dryer Controller M720 Hardware version 1.00 Software version 1.00 Preliminary version Manual M720 Dryer controller Page 1 of 42 Document history Preliminary version: - Created in April, 2009
More informationAPS-1650 LEVEL SENSOR INSTALLATION AND CALIBRATION
APS-1650 LEVEL SENSOR INSTALLATION AND CALIBRATION You will need a 1/16 Allen wrench, a #1 Phillips screwdriver, and two samples of oil. The first should be a clean highly reflective (clear) or red transmission
More informationUser Manual. Digi-Sense TC9600 Advanced Multiparameter Temperature Controller with Thermocouple, Thermistor, and RTD Inputs
User Manual Digi-Sense TC9600 Advanced Multiparameter Temperature Controller with Thermocouple, Thermistor, and RTD Inputs Models 89800-13 and 89800-14 THE STANDARD IN PRECISION MEASUREMENT Table of Contents
More informationProduct Manual SZ1144
Product Manual SZ1144 Refrigeration Temperature Monitor Communicating Controls Description The SZ1144 is a microprocessor-based monitoring and alarm interface designed to monitor up to four 1000 Ω platinum
More informationSCAN200E USER S MANUAL
SCAN200E USER S MANUAL Code No. 2071 1052 rev. 1.4 Code No. 2071 1052 Rev. 1.4 Page 2/16 SCAN200E User s Manual Foreword This manual is for SCAN200E Controller running software version 2.03 or later. We
More informationInstalling ProSeries 2004
Installing ProSeries 2004 The following instructions will walk you through Installing and Launching ProSeries 2004. Before you begin your installation, it is very important to make note of the following
More informationManage Alarms. Before You Begin CHAPTER
CHAPTER 8 Manage Alarms This chapter contains the procedures for viewing and managing the alarms and conditions on a Cisco ONS 15454. Cisco Transport Controller (CTC) detects and reports alarms generated
More informationAVTECH. Digital Active Power Sensor. Installation Note
AVTECH Digital Active Power Sensor AVTECH s Digital Active Power Sensor monitors active power status and ambient room temperatures. Simply strap the sensor to the AC electrical cord of any device that
More informationEL-OEM-3 OEM Packaged Voltage Data Logger
FEATURES PCB Mounted (2.54mm pitch, header sockets) 0 to 2.4V d.c. Measurement Range Logging Rates between 1s and 12hr Stores 64,000 readings USB interface for set-up and data download (USB connector not
More informationSAM. Interface Robot & Trainer Board. User Guide V0211
SAM Interface Robot & Trainer Board User Guide 59892 V0211 Note: Pages 2-7 cover the use of the SAM Interface Robot. See pages 7-8 for the use of the SAM Trainer Board. SAM Interface Robot Materials Included
More informationPHD Dolphin Installation
Summary This document is intended to provide a user with instructions on installing the hardware on a Windows computer 2. Download the Dolphin USB driver by holding down the CTRL key and left clicking
More informationManage Alarms. Before You Begin CHAPTER
CHAPTER 9 This chapter explains how to view and manage the alarms and conditions on a Cisco ONS 15310-CL and Cisco ONS 15310-MA. Cisco Transport Controller (CTC) detects and reports SONET alarms generated
More informationEXPERT TRI-STAR. Temperature controller. User s Manual
Temperature controller r s Manual WARNINGS The warranty can be void if this product is used in a manner not specified by the manufacturer. Every effort has been made to ensure that this manual is complete,
More informationFLX380 and OFL280 FlexTester Series
FLX380 and OFL280 FlexTester Series User Guide www.aflglobal.com or +1 (800) 321-5298, +1 (603) 528-7780 Contents Safety Information... 4 General Information... 5 Contacting Customer Service...5 Recommended
More informationPump-Up Controller MODEL 4062
Pump-Up Controller 4-20mA Input/Scalable Output Seal Fail Monitoring Duplex Pump Alternation Hand-Off-Auto Controls Dual Run-time Meters RS-485/Modbus Communications DESCRIPTION The Model 4062 Pump-Up
More informationHBC-4301 Hot Bonding Controller. Operators Manual
HBC-4301 Hot Bonding Controller Operators Manual January, 2006 TABLE OF CONTENTS TABLE OF CONTENTS... 1 1. GETTING GOING FAST... 7 2. INTRODUCTION... 9 3. SPECIFICATIONS... 11 3.1 HARDWARE SPECIFICATIONS...
More informationManitex Operation Manual
Manitex Operation Manual Introduction The Greer Insight system is designed for use as an aid to crane operation. Do not use this system without a properly trained operator who is knowledgeable in safety
More information1592 In Cab Monitor (ICM) QUICK START GUIDE
1592 In Cab Monitor (ICM) QUICK START GUIDE Refer to your Operators Manual for additional information on controls 89-023 Rev - C 4/2013 Program # 1592.0.45.3 SAFETY Allied Systems Co. is concerned with
More informationIntelliPack : 800 Series
800 Series Models by Function Guide 800T Intelligent Transmitters 800A Intelligent Alarms 890M Math/Computation IntelliPack transmitter units convert sensor inputs to isolated process current or voltage
More informationCBI-064. User Manual. Caddx to KNX-BUS Interface
CBI-064 Caddx to KNX-BUS Interface User Manual GDS Intelligence in Buildings El. Venizelou 116 Nea Erithrea 14671 Tel: +30 2108071288 Email: info@gds.com.gr Web: gds.com.gr Contents 1 Device Description...
More informationQuick start guide. English
Quick start guide English Read your entire Astral User Guide or Clinical Guide before use. The Astral device 1. Adapter port Can be fitted with single limb adapter, single limb leak adapter or double limb
More informationFCR 05, FCR 07. Power factor correction controller. User and service manual
FCR 05, FCR 07 Power factor correction controller User and service manual version 2.3 Czech Republic Czech Republic 1 Content 1. Control and signal elements... 3 2. Device description... 4 3. Instruction
More informationOVEN INDUSTRIES, INC.
OVEN INDUSTRIES, INC. OPERATING MANUAL Model 5C7-252 TEMPERATURE CONTROLLER With PLC Inputs Introduction Thank you for purchasing our controller. The Model 5C7-252 is an exceptionally versatile unit and
More informationRS485 MODBUS Module 8AI
Version 1.4 15/04/2013 Manufactured for Thank you for choosing our product. This manual will help you with proper support and proper operation of the device. The information contained in this manual have
More informationAutomatic Isokinetic Sampler ST5
Automatic Isokinetic Sampler ST5 Automatic Isokinetic Sampler ST5 Description The ST5 is the next generation isokinetic sampler, developed to be efficient, rugged, accurate and user friendly. The perfect
More informationGAMMA OTDR application consists of main window and menu. Using menu user can operate in different modes of application.
GAMMA OTDR Introduction...1 Using GAMMA OTDR...1 Application main window...1 Menu description...2 file...2 instrument...2 mode...5 events...9 view...11 Introduction GAMMA OTDR is the first Android application
More informationVAV Thermostat Controller Specification and Installation Instructions. Model TRO24T4XYZ1
Model TRO24T4XYZ1 Description The TRO24T4XYZ1 is a combination controller and thermostat. The VAV Thermostat Controller is designed for simple and accurate control of any variable air volume box in a number
More informationOxygen & Carbon Dioxide Analyser
Oxygen & Carbon Dioxide Analyser Model 1637-Mk II TABLE OF CONTENTS 1. Overview & Specifications... 3 1.1 Hardware Specifications... 4 1.2 Product & Logging Specifications... 5 1.3 Heater Supply for the
More informationInterior Design Tutorial
Chapter 4: Interior Design Tutorial In the Interior Design Tutorial, we ll pick up where we left off in the House Design Tutorial. The shell and basic structure of our plan is complete, but a lot of interior
More information1 MXS Strada: connect and configure alarm LEDs
1 MXS Strada: connect and configure alarm LEDs Question: How can I activate my MXS Strada (Street Icons version) alarm LEDs so to answer my car/bike signals? Answer: MXS Strada alarm LEDs are not strictly
More informationDigital Control Unit- Installation, Operation & Maintenance IMPORTANT INFORMATION
Environment IMPORTANT INFORMATION It is not anticipated that this equipment will be exposed to adverse environmental conditions without additional protection. Site the equipment in a frost free area. Ensure
More informationOperating manual. Wascator FOM71 CLS
Operating manual Wascator FOM71 CLS Operating manual in original language 438 9200-91/EN 2010.05.03 Register now And be able to join the Wascator FOM 71 CLS web site where you can find: General information
More informationOxygen & Carbon Dioxide Analyser. Model 1737 Operators Manual
Oxygen & Carbon Dioxide Analyser Model 1737 TABLE OF CONTENTS 1. Overview & Specifications... 3 1.1 Hardware Specifications... 4 1.2 Product & Logging Specifications... 5 1.3 Cabinet... 6 1.4 Display...
More informationSurface Concept Product Catalog 2014
Surface Concept Product Catalog 2014 Delayline Detectors MCP Detectors Time-to-Digital Converters Distributor of Surface Concept Products in the United States is Pulse Processing Electronics 727-532-6144
More informationElectronic Pellet Burner Controller NPBC-V3-1
Electronic Pellet Burner Controller NPBC-V3- SOFTWARE VERSION 3.2/3. page of 3 CHANGES IN THE TECHNICAL AND USER GUIDE OR IN THE SOFTWARE VERSION Technical and User Guide's version Changes Page 2.8. The
More informationManage Alarms. Before You Begin CHAPTER
CHAPTER 9 Manage Alarms This chapter contains the procedures for viewing and managing the alarms and conditions on a Cisco ONS 15454 SDH. Cisco Transport Controller (CTC) detects and reports SDH alarms
More informationDistributed By: M&M Control Service, Inc Building Technologies
Building Technologies Combustion Control Systems Count on Siemens. Siemens Building Technologies, the worldwide industry leader in combustion controls, delivers globally approved products specifically
More informationOTDR - FHO5000-xxx. Optical Time Domain Reflectometer
OTDR - FHO5000-xxx Optical Time Domain Reflectometer FHO5000 series Optical Time Domain Reflectometer (OTDR) is the latest generation of intelligent instrument for test and detection of fiber optic communication
More informationAmbient Temperature/ Relative Humidity & Dew Point Temperature Sensors to USB Output. Model LFS108B
Ambient Temperature/ Relative Humidity & Dew Point Temperature Sensors to USB Output Model LFS108B Copyright 2018 - LLC. All rights reserved. Table of Contents Quick Start... 3 1- Introduction... 4 2-
More informationOperators Manual. E15 Seeder Console Air Seeder Monitor A600 R1.3 V2.0.18
Operators Manual E15 Seeder Console Air Seeder Monitor A600 R1.3 V2.0.18 How to use this operators manual As with any software operated equipment, software and/or hardware is in many cases changed and
More information2012 Toolbar & NH3 Operators Manual
2012 Toolbar & NH3 Operators Manual P/N 320379 Amity Technology, LLC 2800 7th Avenue North Fargo, ND 58102 (701) 232-4199 www.amitytech.com This Page Left Intentionally Blank Page 2 2012 Toolbar/NH3 Manual
More informationMOVING FILTER AIR MONITOR ALPHA, BETA/GAMMA PARTICULATES
FEATURES: MOVING AIR FILTER AIRBORNE ALPHA LESS RADON AND BETA/GAMMA PARTICULATES RUGGED, 100% DUTY CYCLE SETTABLE ALARM HIGH THROUGH-PUT UNATTENDED OPERATION 12 WEEKS PRINTED RECORD (Optional) 4 CHANNEL
More informationAdaptive CyCLO Technical and HMI User Guide. CyCLO User Guide. Version th December 2017 REV
CyCLO User Guide Version 2.00 19 th December 2017 REV 2.00 1 Contents 1. Hardware... 3 1.1. Introduction... 3 1.2. Electrical Specification... 3 1.3. Board Overview... 4 1.4. Electrical Installation...
More informationUSER MANUAL USB Multi-Function Datalogger Model RHT35
USER MANUAL USB Multi-Function Datalogger Model RHT35 Additional User Manual Translations available at www.extech.com Introduction Thank you for selecting the Extech multi-function, easy-to-use, portable
More informationLift Station Level Controller
Lift Station Level Controller Installation and Operation Manual 1 California Motor Controls, Inc. Benicia, CA Table of Contents 1. Features Product Overview... 4-6 Access Security... 7 Optional Features...
More informationOperating, Installation and Service Manual W3400H, CLC 41 Clarus Control
Operating, Installation and Service Manual W3400H, CLC 41 Clarus Control 438 9202-01 05.26 Washer extractor, drum volume 400 litres 3 Contents Machine operation... 7 General description... 7 Automatic
More informationStandard Operating Manual
Standard Operating Manual EVG 101 Spray Coater Version 1.1 Page 1 of 24 Contents 1. Picture and Location 2. Process Capabilities 2.1 Cleanliness Standard 2.2 Substrate Size 2.3 Spin speed 2.4 Spin ramp
More informationL CONNECTION NETWORK Commercial Controls
L CONNECTION NETWORK Commercial Controls SIMPLIFIED, CENTRAL CONTROL Simplified Control for Your Facility The L Connection Network not only enhances comfort and energy-efficiency throughout your facilities,
More informationBeacon 200 Gas Monitor Operator s Manual. Part Number: RK Released: 6/6/08
Beacon 200 Gas Monitor Operator s Manual Part Number: 71-2102RK Released: 6/6/08 Table of Contents Chapter 1: Introduction.................................................3 Overview.............................................................3
More informationUSB Multi Function Dataloggers. RHT30 Humidity/Temperature Datalogger. TH30 Dual Temperature Datalogger
USER MANUAL USB Multi Function Dataloggers RHT30 Humidity/Temperature Datalogger TH30 Dual Temperature Datalogger Additional User Manual Translations available at www.extech.com Introduction Thank you
More informationLago SD3. Differential Controller with Speed Control. Operating and Installation Instructions
Lago SD3 Differential Controller with Speed Control Operating and Installation Instructions Please observe the safety instructions and read through this manual carefully before commissioning the equipment.
More informationAvigilon Control Center System Integration Guide
Avigilon Control Center System Integration Guide with Velocity INT-HIRSCH-A-Rev3 Copyright 2013 Avigilon. All rights reserved. No copying, distribution, publication, modification, or incorporation of this
More informationFrequently asked questions: Intelligent Transmitter Series
Frequently asked questions: Intelligent Transmitter Series The Wilcoxon family of Intelligent Transmitters, relay alarms, and communication modules can be used to implement low-cost online vibration monitoring
More information