II SL. Installation Guide. VOLTEX IMS64-2 Dual output indoor flush mount PIR motion detector IMS64-2
|
|
- Lorena Black
- 5 years ago
- Views:
Transcription
1 II SL Installation Guide VOLTEX IMS64-2 Dual output indoor flush mount PIR motion detector IMS64-2
2 TECHNICAL DATA Rated voltage: 220V-240V~ 50/60Hz Load: Load 1( /T1) for Lighting Incandescent: Max. 1200W Halogen: Max. 850W Fluorescent or LED: Max. 300W Load 2(T2A,T2B) for HVAC (Dry contact, not controlled by Lux setting): Max. 3A (normally open contacts) VAC or 5-30VDC Environmental Protection: Sensor IP23 from below, when installed Operating Temperature: -20 C ~ 45 C PACKAGE CONTENTS Power box x 1 Lens shield x 1 Plastic plug x 2 Detector x 1 Wood screw x 2 Instruction manual x 1
3 PRODUCT DESCRIPTION Features This series is for ceiling flush mount with spring clips. A red LED indicator is equipped for indication of Test function and IR setting. Dimension Detector Power Box Ø OPERATION AND FUNCTION Detection Range: Approx. Ø7m/360 at height of 2.5m H 2.5m approx.ø2m approx.ø7m Time Adjustment: Time 1 (for Load 1) with 7 steps adjustable: 30s-1m-5m-10m-20m-30m-TEST (FIG.1) Time 2 (for Load 2) with 7 steps adjustable: 10s-1m-5m-10m-20m-30m-60m (FIG.2) The sensor LED indicator will flash 3 times every time the VR knob is adjusted and the desired step is successfully selected.
4 Lux Adjustment: With 7 steps adjustable (for Load 1 only): lux- (Day Mode) (FIG.3) Load 2 is independent and not controlled by Lux setting. The sensor LED indicator will flash 3 times every time the VR knob is adjusted and the desired step is successfully selected. Sens Adjustment: (For Time 1 & Time 2): approx. 25% ~ 100% (FIG.4) Adjust sensitivity to suit the location and avoid false triggering for T1 for T1&T2 FIG. 1 FIG. 2 FIG. 3 FIG. 4 Test Function Under Test mode the load will switch on for 3 sec to each detection, and switch off for 2 sec before next detection. Under Test mode the Lux setting is deactivated. Day Mode Function Under Day Mode the sensor can operate regardless of brightness level. INSTALLATION AND WIRING Please disconnect power completely and read the entire instruction manual carefully before installation. Installation and assembly of electrical equipment must be carried out by qualified electricians. Contact a qualified electrician in the event of fault or break down. A circuit breaker (250VAC, 10A) type C according to EN of load 1 ( / T1) must be installed in the fixed wiring for protection. A circuit breaker (250VAC, 6A) type C according to EN of load 2 (T2A,T2B) must be installed in the fixed wiring for protection. If using power tools, ensure that they are set to a low torque setting.
5 Wiring T2AT 2B N L /T1 Load Load Power Supply N V~ L 8mm FIG.5 Knockouts for Power Cable Entry There are several layers of knockout at the cable entry where can be trimmed according to the size of power cable to be connected. The existing cable entry is suitable for cable size Ø2.5~4mm. Trim the lower knockouts gradually by layer to reach the ideal space for cable size Ø5~10mm. If more space is required, please also trim upper knockout gradually by layer to reach the space up to Ø15mm. E D A B C
6 Suitable Cable Size Ø2.5~4mm Ø5~6mm Ø7~8mm Ø11~12mm Ø13~14mm Ø15~15.5mm Knockout Layer Existing cable entry Trim layer A Trim layer A+B Trim layer A+B+C Trim layer A+B+C+D Trim layer A+B+C+D+E Installation Procedure 1. To install the detector, please drill a hole with diameter of 64~68mm on ceiling board and keep the power cable outside. Please strip off 6-8mm of cable sheathing for wiring (FIG.6). 2. Please refer to illustration of FIG.5 for correct wiring. 3. Insert the power module into the ceiling first, raise the two spring clips, and insert the detector into the drilled hole on ceiling (FIG.7). 4. Detection range can be extended with additional slave sensors. 5. Restore the power supply. =64~68 Drill a hole with =64~68mm on the ceiling Power box 6-8mm 30-35mm FIG. 6 FIG. 7
7 Walk Test It takes about 60 sec for sensor to warm up after power is supplied. The purpose of walk test is to check and adjust the detection coverage at the installation of sensor. Set Time VR knob to Test, and then conduct the walk test. Pay attention to the walking direction in the walk test. The sensor is more sensitive to movement across the detection range and less sensitive to movement directly towards it. The load will switch ON for 3 sec for each movement detected, and switch OFF for 2 sec before next trigger. Set the Time VR knob to the desired setting after walk test. When using IR remote control to enter Test mode, it will exit Test mode after 10 min. The sensor LED indicator will stay ON during the warm up period. For remote controllable models, the sensor LED indicator will blink during the warm up period if the sensor has previously been programmed via remote control.. Usage of Lens Shield Undesired detection areas can be shielded off by fixing the enclosed lens shield onto the lens. Trim the lens shield with scissors either horizontally or vertically until the desired detection area is obtained. TROUBLE SHOOTING 1. Unit will not function at all/lights won t turn on - Check wiring to make sure that you have correct AC power at the unit. - Check the wiring from the unit to the source of power to make sure you have wired the unit correctly. - Check the ambient light control to see if it was set at your desired level. 2. Detector clicks but does not work - Check if lamps are broken. - Check if lamps are tight in lampholders. 3. Lights go on and off quickly - Ensure light and heat are not being reflected onto the detector. Check for white or reflective surfaces that may be causing the problem.
8 - Note the detector is more sensitive in cold weather. - Make sure the sensor is not installed close to air-conditioner. - Make sure the Time setting is not set to Test Mode position. 4. Lights stay on - Light bulb sockets may be wired directly to the power source -Recheck the wiring diagram. - Adjust time to minimum, and ensure unit is firmly fixed to a solid object with no moving branches etc. in field of view. - Ensure detector is not being activated by stray moving heat sources such as heating outlets. - Fit the lens shield to eliminate triggering outside detection field. - Reduce the sensitivity level. 5. Detector goes on under windy and rainy conditions - Adverse weather conditions and temperature changes can result in unwanted activations. - This can be minimized by mounting in a protected location. 6. Maintenance and repair - Do not attempt to repair as this could invalidate warranty or result in personal injury. - Clean detector lens and outside casing with damp cloth. Voltex Electrical Australia P: E: sales@voltexelectrical.com.au New Zealand P: E: sales@voltexelectrical.co.nz
Ceiling PIR HS presence detector. Product Guide. Overview. Features
Product Guide 796-2047 Ceiling PIR HS presence detector Overview The 796-2047 (passive infrared) presence detector provides automatic control of lighting loads with optional manual control. This is a high
More informationHigh Frequency Sensor
Model: HF1 Installation & Operating Instructions High Frequency Sensor 1. Specifications: 1. Power: AC 220 ~ 240V 50MHz. 2. Sensor Technology: 5.8GHz High Frequency. 3. Switching capacity: 1000W Incandescent
More information360º Surface Mount Ceiling PIR Light Controller
360º Surface Mount Ceiling PIR Light Controller Model: PDRS1500 Installation & Operating Instructions 1 1. General Information These instructions should be read carefully and retained for further reference
More information5W LED Energy Saver PIR Bulkhead
5W LED Energy Saver PIR Bulkhead Model: LED88PIR Black Installation & Operating Instructions 1. General information: The unit utilises passive infrared technology to detect heat radiation of moving human
More information64.7 Ø85. (1) Sensor inset (2) Lens pluggable. (3) Protection cover (covers the high-voltage terminals). (4) Ceiling (drill hole Ø70mm).
Flush Mount PIR Motion Sensor PIR 1-10V Dimming with Remote Control Mechanical Structure 70mm 64.7 4 56 68.1 73.3 Ø85 3 (1) Sensor inset (2) Lens pluggable Infrared receiver 1 Photocell LED indicator (3)
More information60W Multi PIR Bulkhead
60W Multi PIR Bulkhead Model: MLB98 Black Installation & Operating Instructions 1. General information: The unit utilises passive infrared technology to detect heat radiation of moving human bodies. Upon
More information1. Basic safety information 3 2. Proper use 3
310481 01 EN Motion detectors theluxa P220 WH 1010605 theluxa P220 BK 1010606 theluxa P300 WH 1010610 theluxa P300 BK 1010611 1. Basic safety information 3 2. Proper use 3 Disposal 3 3. Description 4 4.
More informationUser Manual 120/240/300 Outdoor Motion Detector
User Manual 120/240/300 Outdoor Motion Detector Swiss Garde 4000 Warning! - Any work on the main power supply must only be completed by trained specialists. - The product must be installed in accordance
More informationPMCSF6 OCCUPANCY SENSOR
PMCSF6 OCCUPANCY SENSOR Lens Main Body Power Cord INTRODUCTION The use of occupancy detectors in commercial and industrial applications can significantly reduce energy usage lessening both energy costs
More informationIntegrated PIR detectors
EBMINT - Product Guide Integrated PIR detectors Overview The EBMINT series of miniature PIR (passive infrared) presence detectors provide automatic control of lighting loads with optional manual control
More information2000W PIR LIGHT CONTROLLER SLB2000-Black SLW2000-White INSTALLATION & OPERATING INSTRUCTIONS
2000W PIR LIGHT CONTROLLER SLB2000-Black SLW2000-White INSTALLATION & OPERATING INSTRUCTIONS SLB2000 PIR LIGHT CONTROLLER - BLACK WEATHERPROOF IP44 PIR SWITCHING 2000w MAXIMUM MANUAL ON/OFF OVERRIDE TIME
More informationCeiling PIR HS presence detector 1-10V, low temperature. PIR Sensor. IR Receiver. Light Level Sensor. Status LEDs. IR Receiver
Product Guide EBDHS-AD-LT30 Ceiling PIR HS presence detector 1-10V, low temperature Overview The EBDHS-AD-LT30 PIR (passive infrared) presence detector provides automatic control of lighting loads with
More informationModel: MLSA360N. Installation & Operating Instructions. 360º Night Eye PIR Light Controller
Model: MLSA360N Installation & Operating Instructions 360º Night Eye PIR Light Controller Motion Sensor Detection Perspective View 5 metre 1 Ceiling Mount Position 0º Sensor Tilt Up 3º 3º 5 metre Sensor
More informationTOCR02 2 PART MICRO MOTION SENSOR W/IR REMOTE CONTROLLER
TOCR0 PART MICRO MOTION SENSOR W/IR REMOTE CONTROLLER SAFETY PRECAUTIONS Be sure to switch off power source before installing. Make sure that the power wiring comes from circuit with an external 16A miniature
More informationCompact Movement Activated Sensor Installation Instructions
MAL540 Instructs. 12/7/06 3:43 PM Page 3 Compact Movement Activated Sensor Installation Instructions MAL540 series 2 Where to fit your Security Sensor To achieve best results for outside use the Arlec
More informationPPAD-C-230V. Ceiling PIR presence/absence detector. Product Guide. Overview. Features
Product Guide PPAD-C-230V Ceiling PIR presence/absence detector Overview The PPAD-C-230V passive infrared presence detector provides automatic control of lighting loads with optional manual control. The
More informationDETECTOR TRANSMITTER INSTALLATION & OPERATING. Cat No. TLTX2000B INSTRUCTIONS
DETECTOR TRANSMITTER Cat No. TLTX2000B INSTALLATION & OPERATING INSTRUCTIONS 1 Introduction The TLTX2000B Controller Transmitter is part of the Timeguard range of PIR products which communicate by radio
More informationFor assistance with the product please contact: HELPLINE. For a product brochure please contact:
For assistance with the product please contact: HELPLINE 020 8450 0515 or email helpline@timeguard.com For a product brochure please contact: Timeguard Limited. Victory Park, 400 Edgware Road, London NW2
More informationIP 55 (category II) IP 54 (category II) 4. Connection. 1. Basic safety information. 2. Proper use. 5. Installation. 3. Description.
EN Motion detectors theluxa P0 WH 0 theluxa P0 BK 0 theluxa P00 WH theluxa P00 BK. Basic safety information WARNING anger of death through electric shock or fire! ¾Installation should only be carried out
More informationFor assistance with the product please contact: HELPLINE. For a product brochure please contact:
For assistance with the product please contact: HELPLINE 020 8450 0515 or email helpline@timeguard.com For a product brochure please contact: Timeguard Limited. Victory Park, 400 Edgware Road, London NW2
More information1. Basic safety information 3 2. Proper use 3
307146 03 EN Presence detector thepiccola P360-100 DE WH 2090200 1. Basic safety information 3 2. Proper use 3 Disposal 3 3. Device description 4 4. Installation and connection 4 Installing the presence
More informationSWITCHLITE MRE SLD MAN SWITCHLITE MRE SLD IP55
96239823 SWITCHLITE MRE SLD MAN 96239821 SWITCHLITE MRE SLD IP55 Overview The SWITCHLITE MRE SLD PIR (passive infrared) presence detector provides automatic control of lighting loads with optional manual
More informationMotion detector themova P360 KNX UP WH themova P360 KNX UP GR
307079 EN Motion detector themova P360 KNX UP WH 1039600 themova P360 KNX UP GR 1039601 1. Product characteristics 4 2. Safety 5 3. Proper use 6 4. Function 6 5. Detection area 10 6. Installation 13 7.
More informationMWS5. Miniature Microwave Presence Detector (standalone) Product Guide. Overview. Features
Product Guide MWS5 Miniature Microwave Presence Detector (standalone) Overview The MWS5 series of miniature microwave presence detectors provide automatic control of lighting loads with optional manual
More informationEBDSPIR-PRM-2CH, EBDSPIR-PRM-2CH-NC
Product Guide EBDSPIR-PRM-2CH, EBDSPIR-PRM-2CH-NC Ceiling PIR presence/absence detector 2 channel Overview The EBDSPIR-PRM-2CH PIR (passive infrared) presence detector provides automatic control of lighting
More informationEBMHS (standard & slim-line PSU)
Product Guide EBMHS (standard & slim-line PSU) Miniature HS PIR Presence Detector (luminaire fitting) Overview The EBMHS series of miniature PIR (passive infrared) presence detectors provide automatic
More informationMotion Sensor. For Outdoor Use. Wall & ceiling mounted. Quick & Easy Installation 2 Channels
MS3602CH 2 Channel Motion Sensor For Outdoor Use Wall & Ceiling Mounted Quick & Easy Installation 2 Channels Channel 2 Distance Wiring Diagram 220-240V ~ 50Hz 14A Max. (cosø=1) 3000W for incandescent load
More informationEBDSPIR-PRM-VFC & EBDSPIR-PRM-VFC-NC
Product Guide EBDSPIR-PRM-VFC & EBDSPIR-PRM-VFC-NC Ceiling PIR presence/absence detector Overview The EBDSPIR-PRM-VFC PIR (passive infrared) presence detector provides automatic control of lighting loads
More information1. Basic safety information 3 2. Proper use 3
307274 EN Motion detector theluxa R180 WH 1010200 theluxa R180 BK 1010201 1. Basic safety information 3 2. Proper use 3 Disposal 3 3. Connection 4 4. Installation 5 Installation instructions 5 5. Description
More information360º FLUSH MOUNT CEILING PIR LIGHT CONTROLLER INSTALLATION & OPERATING. Cat No. SLFM360 INSTRUCTIONS
360º FLUSH MOUNT CEILING PIR LIGHT CONTROLLER Cat No. SLFM360 INSTALLATION & OPERATING INSTRUCTIONS 1 Introduction The SLFM360 utilises passive infrared technology to detect heat radiation of moving human
More informationPRODUCT INFORMATION. Uses tough, high quality PC diffuser, resistant to fracture and to ultraviolet light to limit discolouring.
Ø297mm Packing list in Ceiling Mount Lamp LEDS 96PCS Φ6 Wall plug 3x30 Screw Φ3 Sealing ring 4x12 Y type Stainless Screw Quantity 1X 4X 4X 3X 3X PRODUCT INFORMATION 98.5mm Ideal for energy saving this
More informationLPCMPIRM65 & LPCMPIRDSI65
Product Guide LPCMPIRM65 & LPCMPIRDSI65 Luminaire high mount PIR detectors Overview The LPCMPIR PIR (passive infrared) presence detector provides automatic control of lighting loads with optional manual
More informationEBDSPIR-PRM-LV Product Guide
EBDSPIR-PRM-LV Product Guide Ceiling PIR presence/absence detector 12-24V AC/DC Overview The EBDSPIR-PRM-LV PIR (passive infrared) presence detector provides automatic control of low voltage loads including
More information30W LED PIR FLOODLIGHT. Model: LEDX30PIRB Model: LEDX30PIRWH
30W LED PIR FLOODLIGHT Model: LEDX30PIRB Model: LEDX30PIRWH 1. Designated Use LEDX30PIR is an outdoor motion detector for automatic LED lighting control. Mainly for wall installation. Simple plug in wall
More informationEBDHS-DD-LT30. Ceiling PIR HS presence detector DALI / DSI, low temperature. Product Guide. Overview. Features
EBDHS-DD-LT30 Product Guide Ceiling PIR HS presence detector DALI / DSI, low temperature Overview The EBDHS-DD-LT30 PIR (passive infrared) presence detector provides automatic control of lighting loads
More informationMounting bezel Retaining spring. Detects movement within the detection range, allowing load control in response to changes in room occupancy.
Installation Guide High-Bay PIR Presence/Absence Detector (317) The 317 High-Bay PIR Presence/Absence Detector, in conjunction with a Helvar lighting control system, provides automatic control of lighting
More informationDetector switch - Dual Tech
Page 1. Use.................................... 1 2. Technical characteristics................1 3. Dimensions............................ 2 4. Connection........................... 2 5. Installation...........................
More information3. Proper use. 4. Function. 1. Product characteristics. 2. Safety. Function description. Channel A light. Motion detector
307021 3. Proper use EN Motion detector themova P360-100 UP WH 1030600 themova P360-100 UP GR 1030601 The motion detector is intended for interior. The motion detector is eclusively intended for the use
More informationProduct and Applications Description
Product and Applications Description The presence detector with a sensing range of 360 allows the automatic execution of control functions in the electrical system by detecting movements. For example,
More informationSurface Mount Wall PIR Light Controller. Model: PDWM1500. Installation & Operating Instructions
Surface Mount Wall PIR Light Controller Model: PDWM1500 Installation & Operating Instructions 1. Introduction The PDWM1500 utilises passive infrared technology to detect heat radiation of moving human
More informationECO-IR 360C NT. Presence detector. Art. Nr Bedienungsanleitung 2. Notice d utilisation 22. Installation manual 42
Presence detector ECO-IR 360C NT Art. Nr. 202 0 400 D F GB E I NL S N FIN DK Bedienungsanleitung 2 Notice d utilisation 22 Installation manual 42 Manual de instrucciones 62 Istruzioni per l uso 82 Gebruikershandleiding
More informationHigh bay PIR presence detector 1-10V dimming. PIR Sensor. IR Receiver. Light Level Sensor. Status LEDs. IR Receiver
Product Guide EBDSPIR-HB-AD High bay PIR presence detector 1-10V dimming Overview The EBDSPIR-HB-AD PIR (passive infrared) presence detector provides automatic control of lighting loads with optional manual
More informationProduct Guide. Ceiling PIR HS presence detector DALI / DSI dimming. PIR Sensor. IR Receiver. Light Level Sensor. Status LEDs.
PPAD-C-HB-DALI-230V Product Guide Ceiling PIR HS presence detector DALI / DSI dimming Overview The PPAD-C-HB-DALI-230V PIR (passive infrared) presence detector provides automatic control of lighting loads
More informationHigh bay PIR presence detector DALI / DSI dimming. PIR Sensor. IR Receiver. Light Level Sensor. Status LEDs. IR Receiver
EBDSPIR-HB-DD Product Guide High bay PIR presence detector DALI / DSI dimming Overview The EBDSPIR-HB-DD PIR (passive infrared) presence detector provides automatic control of lighting loads with optional
More informationSystem 2000 System 2000 automatic control switch Safety instructions. 2 Device components
pure white Order-No. : 2270 02 colour aluminium Order-No. : 2270 04 Operating instructions 1 Safety instructions Electrical equipment may only be installed and fitted by electrically skilled persons. Failure
More informationEco-sensors - PIR. Catalogue number(s): / / Use. 1. Use Technical characteristics (continued)
Page. Use..................................... 2. Technical characteristics................. 3. Dimensions.............................2 4. Connection.............................2 5. Removal................................3
More information"Options" Sensor Module
"Options" Sensor Module E-790B INSTALLER GUIDE V1.1-2/07 IQ-SNL-MOD-180 IQ Europe Limited Sandbeck Lane, Wetherby LS22 7TW. Visit us at www.iq-europe.co.uk Installation helpline 0871 717 1100 MANUFACTURER'S
More informationVITMR-EBDSPIR-PRM. PIR Presence/Absence Detector IR with Ceiling Rose. Product Guide. Overview. Features
Product Guide VITMR-EBDSPIR-PRM PIR Presence/Absence Detector IR with Ceiling Rose Overview The VITMR-EBDSPIR-PRM PIR (passive infrared) presence detector provides automatic control of lighting loads.
More informationModel: PDFM1500. Installation & Operating Instructions 360º Flush Mount Ceiling PIR Light Controller
Model: PDFM1500 Installation & Operating Instructions 360º Flush Mount Ceiling PIR Light Controller can cause to your immediateneighbours.light pollution caused by incorrectly installing a unit or over-lighting
More informationMotion Sensor. Specifications
Used for motion activated and dusk to dawn lighting control of flood lights, area lights, etc. Durable weatherproof construction utilizing infrared technology to sense temperature changes caused by movement
More informationSystem 2000 System 2000 presence detector Comfort top unit. 1 Safety instructions. 2 Device components
pure white Order-No. : 0317 02 colour aluminium Order-No. : 0317 04 Operating instructions 1 Safety instructions Electrical equipment may only be installed and fitted by electrically skilled persons. Failure
More informationMWS6-PRM. Ceiling microwave presence/absence detector. Product Guide. Overview. Features
Product Guide MWS6-PRM Ceiling microwave presence/absence detector Overview The MWS6-PRM microwave presence detector provides automatic control of lighting loads with optional manual control. The MWS6-PRM
More information360 Surface Mount Ceiling PIR Light Controller
360 Surface Mount Ceiling PIR Light Controller Model: SLW360L Installation & Operating Instructions 1 1. General Information These instructions should be read carefully and retained for further reference
More information1. Product characteristics 4 2. Safety 5 3. Proper use 5 4. Operation 6
307214 1103107701 EN Presence detector theronda S360-101 DE WH 2080565 theronda S360-101 DE GR 2080566 theronda S360-101 AP WH 2080555 theronda S360-101 AP GR 2080556 1. Product characteristics 4 2. Safety
More informationµdim Microwave Sensors User Manual
Microwave Sensors User Manual P e o p l e I n n o v a t i o n s S o l u t i o n s 1. Introduction µdim Table of Contents Page Introduction 2 Technical data 3 Dimensions and mounting options 9 Connections
More informationPSC-ID-x-CM Series Ceiling Mount Occupancy Sensor
TECHNICAL SPECIFICATIONS PSC-ID-x-CM Series Ceiling Mount Occupancy Sensor Basic Features Line voltage version: 120-277VAC, 60Hz Low voltage version: 24VDC, requires separate class 2 power supply PIR sensor
More informationMWS3A-PRM. Ceiling microwave presence/absence detector. Product Guide. Overview. Features
Product Guide MWS3A-PRM Ceiling microwave presence/absence detector Overview The MWS3A-PRM microwave presence detector provides automatic control of lighting loads with optional manual control. The MWS3A-PRM
More information, ,
796-2028, 796-2021, 796-2025 Batten mount PIR detectors Overview This series of miniature PIR (passive infrared) presence detectors provide automatic control of lighting loads with optional manual control
More informationModel: PDSM1500. Installation & Operating Instructions 360º Surface Mount Ceiling PIR Light Controller
Model: PDSM1500 Installation & Operating Instructions 360º Surface Mount Ceiling PIR Light Controller Considerate Lighting pollution bythe incorrectly installing a unit an or area Please be caused aware
More informationPIR/INT & PIR/INT-D. Batten mount PIR detectors. Product Guide. Overview. Features
Product Guide PIR/INT & PIR/INT-D Batten mount PIR detectors Overview The PIR/INT & PIR/INT-D miniature PIR (passive infrared) presence detectors provide automatic control of lighting loads with optional
More informationLPC3BSP65 & LPC3BDP65
Product Guide LPC3BSP65 & LPC3BDP65 Batten mount PIR detectors Overview The LPC3B series of miniature PIR (passive infrared) presence detectors provide automatic control of lighting loads with optional
More informationSECURITY LIGHT MODEL NO: CL6PIR OPERATION INSTRUCTIONS PART NO: GC0215
SECURITY LIGHT MODEL NO: CL6PIR PART NO: 4003535 OPERATION INSTRUCTIONS GC0215 INTRODUCTION Thank you for purchasing this CLARKE Security Light with motion sensor. The motion sensor is a small electronic
More informationUP 258E11 OPTISENS OFFICE
Product and functional description The UP 258E11 is a presence/motion detector with integrated 2-point light control. The UP 258E11 device communicates via KNX/EIB with actuators or other KNX devices.
More informationProduct Guide. Ceiling microwave presence detector DALI / DSI. Microwave Sensor. IR Receiver. Light Level Sensor. Status LEDs.
MPAD-C-DALI-230V Product Guide Ceiling microwave presence detector DALI / DSI Overview The MPAD-C-DALI-230V microwave presence detector provides automatic control of lighting loads with optional manual
More information360 Ceiling PIR Light Controller
360 Ceiling PIR Light Controller Model: SLFM360L Installation & Operating Instructions 1 1. General Information These instructions should be read carefully and retained for further reference and maintenance.
More informationPRODUCT DATA AND INSTALLATION SHEET MWS5-SA STAND ALONE MINIATURE CEILING MOUNTED MICROWAVE PRESENCE DETECTOR
8. SPECIFICATION LOAD 6 Amps fluorescent and incandescent lighting. 3 Amps compact fluorescent lighting. 3 Amps low energy lighting. 3 Amps low voltage lighting (switch primary of transformer). Switch
More informationProduct Guide. Ceiling PIR presence detector DALI / DSI dimming. PIR Sensor. IR Receiver. Light Level Sensor. Status LEDs.
Product Guide LPCMPIRDSI Ceiling PIR presence detector DALI / DSI dimming Overview The LPCMPIRDSI PIR (passive infrared) presence detector provides automatic control of lighting loads with optional manual
More informationDescription FEATURES. l Innovative dual mount system requires only one sensor for either flush or surface mount applications
Simple Fit Switching Sensors 1.8m to 3m Cone-shaped detection pattern, 6m radius at mounting height 6.0m AC220~240V/50Hz MK Simple Fit Sensors offer cost effective presence detection for lighting control
More information12W Round LED Wall/Ceiling Light with Microwave Sensor
12W Round LED Wall/Ceiling Light with Microwave Sensor Model: LEDSR12WHMS Installation & Operating Instructions 1 1. General Information These instructions should be read carefully and retained for further
More informationEBMPIR-MB. Batten mount PIR detectors. Product Guide. Overview. Features
Product Guide EBMPIR-MB Batten mount PIR detectors Overview The EBMPIR-MB series of miniature PIR (passive infrared) presence detectors provide automatic control of lighting loads with optional manual
More informationINSTALLATION INSTRUCTIONS - POWER SENTRY CONTROL POWER SENTRY CONTROL UNIT PSBCEB2 INSTALLATION INSTRUCTIONS
POWER SENTRY CONTROL UNIT PSBCEB2 INSTALLATION INSTRUCTIONS READ AND FOLLOW THESE INSTRUCTIONS BEFORE INSTALLATION TO ENSURE PROPER AND SAFE OPERATION SAVE THESE INSTRUCTIONS READ AND FOLLOW ALL SAFETY
More informationMPAD-C 12-24V. Ceiling microwave presence/absence detector 12-24V AC/DC. Product Guide. Overview. Features
Product Guide MPAD-C 12-24V Ceiling microwave presence/absence detector 12-24V AC/DC Overview The MPAD-C 12-24V Microwave presence detector provides automatic control of low voltage loads including lighting
More informationThe Power To Supply... All Your Electrical Products
ENERGY EFFICIENT RETROFIT SOLUTIONS The Power To Supply... All Your Electrical Products www.cef.co.uk All products are subject to availability and are correct at the time of print. Errors and omissions
More informationCeiling Microwave presence/absence detector 12-24V AC/DC
MWS3A-PRM-LV Product Guide Ceiling Microwave presence/absence detector 12-24V AC/DC Overview The MWS3A-PRM-LV Microwave presence detector provides automatic control of low voltage loads including lighting
More information1 Safety instructions. 2 Device components. Presence detector. Operating instructions
Presence detector Standard Art. No. 3361 WW Presence detector Standard Art. No. 3361 AL Presende detector Universal Art. No. 3361-1 WW Presende detector Universal Art. No. 3361-1 AL Operating instructions
More informationBIANCO SENSOR FLUSH MOUNT 15W MODEL # GBCL400HFSR
BIANCO SENSOR FLUSH MOUNT 15W MODEL # GBCL400HFSR DESCRIPTI & FEATURES With High Frequency Occupancy On/ Off Sensor ; HF System: 5.8GHz±75MHz, ISM wave band Sensor Power consumption : 0.5W(- standby);
More informationSave energy. ARGUS presence detectors
Save energy Ef cient energy use 2 Keeping energy costs down Increasing energy costs and growing awareness of the environment in modern buildings management now mean that more innovative solutions for efficient
More informationCeiling Microwave presence detector - DALI / DSI 12-24V AC/DC. Microwave Sensor. IR Receiver. Light Level Sensor. Status LEDs.
MWS6-DD-LV Product Guide Ceiling Microwave presence detector - DALI / DSI 12-24V AC/DC Overview The MWS6-DD-LV microwave presence detector provides automatic control of lighting loads with optional manual
More informationCeiling PIR presence detector DALI / DSI dimming. PIR Sensor. IR Receiver. Light Level Sensor. Status LEDs. PIR Sensor.
Product Guide EBDSM-DD Ceiling PIR presence detector DALI / DSI dimming Overview The EBDSM-DD PIR (passive infrared) presence detector provides automatic control of lighting loads with optional manual
More information2 x CR123A Lithium batteries. White night-light LED. Blue alarm LED - also glows behind the lens. Ambient light sensor behind lens.
15m x 15m wide angle coverage Look down Creep Zone White LED motion activated night-light Adjustable Pulse Count Adjustable Range High R.F. and E.S.D. immunity High white light immunity SAWR stabilised
More informationDetailed operating instructions
MA00613903 Detailed operating instructions MD 360/8 Basic EB10430404 MD 360i/8 Basic EB10430428 MD 360/24 Basic EB10430848 MD 360i/24 Basic EB10430862 MD 360/8 Basic SMB EB10430497 MD 360i/8 Basic SMB
More informationSchneider Electric occupancy sensor range. Lighting the way to simple energy saving solutions
Schneider Electric occupancy sensor range Lighting the way to simple energy saving solutions Take control.. and reap the rewards Lighting control is becoming increasingly popular as it offers energy savings
More information3. Intended use. 4. Function. 1. Product characteristics. 2. Safety. Functional description. Channel A light. Motion detector
EN Motion detector themova S360-101 DE WH 1030565 themova S360-101 DE GR 1030566 themova S360-101 AP WH 1030555 themova S360-101 AP GR 1030556 1. Product characteristics 307067 Passive infra-red motion
More informationIP65 High Bay Dual Sense Sensor
IP65 High Bay Dual Sense Sensor TM and, 1-10V Dimming with Remote Control Technical Data Input Characteristics Sensor Data Model No. Model No. Mains voltage 220-240VAC 50/60Hz Sensor principle High Frequency
More informationInstallation Instructions
Specifications PW-100 PW-200 PW-100/PW-100-347/PW-200/PW-200-347 v3 Passive Infrared Wall Switch Occupancy Sensor PW-100-347 PW-200-347 Voltages: PW-100 & PW-200................ 120/277VAC, 50/60Hz PW-100-347
More informationluxcontrol lighting control system basicdim basicdim ILD Compact control module with ambient light sensor and motion sensor
ILD Compact control module with ambient light sensor and motion sensor Compact dimensions for luminaire installation For up to 10 DSI or DALI devices (max. 5 per output channel) 2 DALI/DSI output channels
More informationDUAL ZONE OUTDOOR PIR MS-12TE & MS-12FE
DUAL ZE OUTDOOR PIR MS-12TE & MS-12FE INSTRUCTI MANUAL We appreciate your purchase of a TAKEX passive infrared sensor. This sensor will provide long and dependable service when properly installed. Please
More informationDetailed operating instructions
MA00744002 Detailed operating instructions MD-FLAT 360i/8 RW EP10427886 MD-FLAT 360i/8 SW EP10427893 MD-FLAT 360i/8 RB EP10428074 MD-FLAT 360i/8 SB EP10428081 MD-FLAT-E 360i/8 RW GST EP10427862 MD-FLAT-E
More informationData sheet. Function description. Benefits
uminaire-integrated modules ENOTEC modular system 110046819 Control CD I 110046818 Control CD CO1 110046814 ensor ED HF1 110046813 ensor ED HF2 110046816 ensor ED PIR Function description The new ENOTEC
More informationNO (SPST-NO) 10 A Internal installations Particularly suited for wall mounting
Features PIR movement detector for internal or external installations - wall mounting Small size Adjustable ambient light intervention threshold Adjustable Light On Time Universal mounting position - permits
More informationINSTALLATION INSTRUCTIONS - PS1055LCP & PS1555LCP LED EMERGENCY DRIVER PS1055LCP & PS1555LCP
LED EMERGENCY DRIVER PS1055LCP & PS1555LCP INSTALLATION INSTRUCTIONS READ AND FOLLOW THESE INSTRUCTIONS BEFORE INSTALLATION TO ENSURE PROPER AND SAFE OPERATION SAVE THESE INSTRUCTIONS LED EMERGENCY DRIVER
More informationInstallation Guide. Ceiling PIR Detector (311) Features and Connections
Installation Guide Ceiling PIR Detector (311) The 311 Ceiling PIR Detector is a compact unit containing sensors to provide energy-saving functions when used in a DALI system. Functioning as a presence
More informationUnpack, connect, done - no further work required
DELTA Switches and Socket Outlets DELTA reflex Motion Detectors, IP55 Unpack, connect, done - no further work required A key feature of the DELTA reflex motion detector IP55 is the precision with which
More informationGE Lighting. Lighting Controls. DALI Digital Lighting Controls
GE ighting ighting Controls I Digital ighting Controls the I Protocol Multi-functional control of I-ready GE uminaires 1-1 to I converters available for analogue luminaires I CB Type 2 - complete programmable
More informationSecurity Light Transmitter
SF-PTV180-150-T.qxd 13/04/2005 13:48 Page 1 Security Light Transmitter E-995 INSTALLER GUIDE V1.0-04/05 IQ-PTV180-150-TX-T IQ Europe Limited Sandbeck Lane, Wetherby LS22 7TW. Visit us at www.iq-europe.co.uk
More informationELECTRONIC SOUNDER STROBE Model : AVD-C407
ELECTRONIC SOUNDER STROBE Model : AVD-C407 MULTRON range of combination Electronic Sounders with Strobe Lights are designed to complement our Fire Alarm products both technically and aesthetically as an
More informationInfrascan Passive Infrared Motion Sensor Surface-Mount 753SSR Series. Installation Instructions
Infrascan Passive Infrared Motion Sensor Surface-Mount 753SSR Series Installation Instructions Contents 1.0 Product Range...3 2.0 Principle of Operation...3 3.0 Field of View...3 4.0 System Components
More informationMWS3 Ceiling Mount Microwave Occupancy Detector
MWS3_0916/ISSUE1 MWS3 Ceiling Mount Microwave Occupancy Detector Description: the MW3SA offers a unique presence/absence detection capability by using an adjustable head. This incorporates an innovative
More information18W Round LED Wall/Ceiling Light with Microwave Sensor
18W Round LED Wall/Ceiling Light with Microwave Sensor Model: LEDMR18WHMS Installation & Operating Instructions 1 1. General Information These instructions should be read carefully and retained for further
More information11,9. Ordering data. Max. cable length sensor head 1 basicdim ILD lx 150 lx m 1
Compact dimensions for luminaire installation For up to 10 DSI or DALI devices (max. 5 per output channel) DALI/DSI output channels with adjustable negative offset from channel to channel 1 Ambient light
More information