Honeywell Modbus Solution: 7800 Series Burner Controller through S7810M Modbus Module

Transcription

1 Point Map August 1, 2006 Systems Integration Honeywell Modbus Solution: 7800 Series Burner Controller through S7810M Modbus Module Table Series Burner Controller through S7810M Modbus Moduler APOGEE Points, Application Number: Point Type Range/Units abc 1 LAO Address 2 LAI Application 3 LDI No Communication Off/On 4 LAO IP Address Byte 1 5 LAO IP Address Byte 2 6 LAO IP Address Byte 3 7 LAO IP Address Byte 4 8 LAO Modbus IP Port 9 LAO Base Offset 10 LAO Send Initial 11 LAI Fault Code 12 LAI Sequence State 13 LAI Sequence Time sec 14 LAI Flame 1 Signal Strenght V 15 LAI Flame Failure Response Time sec 16 LAI Purge Time sec 17 LAI TOTAL CYCLES ( ) cycles 18 LAI TOTAL HOURS ( ) hrs 19 LAO Burner Control 20 LDI Initiate No/Yes 21 LDI Standby No/Yes 22 LDI Purge No/Yes 23 LDI Pilot Ignition Off/On 24 LDI Main Ignition Off/On 25 LDI Run Stop/Run 26 LDI Postpurge No/Yes Siemens Building Technologies, Inc. Page 1 of 10

2 Table Series Burner Controller through S7810M Modbus Moduler APOGEE Points, Application Number: (continued) Point Type Range/Units abc 27 LDI Pre-ignition Off/On 28 LDI Reserved 28 Off/On 29 LDI Reserved 29 Off/On 30 LDI Reserved 30 Off/On 31 LDI Reserved 31 Off/On 32 LDI Reserved 32 Off/On 33 LDI Alarm3 Off/On 34 LDI Hold No/Yes 35 LDI Lockout3 No/Yes 36 LDI Auto Operation use pre-programmed control Limits Manual/Auto 37 LDI Do Not Fire. The burner will remain off No/Yes 38 LDI High Fire. Maintain pre-programmed High Firing rate No/Yes 39 LDI Low Fire Maintain pre-programmed Low Firing rate No/Yes 40 LDI Controller Reset. Forced Reset/Restart Normal/Reset 41 LDI Reserved 41 Off/On 42 LDI Reserved 42 Off/On 43 LDI Reserved 43 Off/On 44 LDI Reserved 44 Off/On 45 LDI Reserved 45 Off/On 46 LDI Reserved 46 Off/On 47 LDI Reserved 47 Off/On 48 LDI Reserved 48 Off/On 49 LDI Reserved 49 Off/On 50 LDI Reserved 50 Off/On 51 LDI Reserved 51 Off/On a s noted for LDIs and LDOs are in the following format: OFF text/on text. b This column indicates the value/range or engineering units or both if known. c The default English value is not italicized. An italicized entry indicates an SI value. Table 2. Fault Code. 0 No Fault 1 No Purge Card 2 AC Frequency/Noise 3 AC Line Dropout Page 2 of 10 Siemens Building Technologies, Inc.

3 4 AC Frequency 5 Low Line Voltage 6 Purge Card Error 7 Flame Amplifier 8 Flame Amp/Shutoff 9 Flame Detected 10 Pre-ignition InterLock 11 Running InterLock On 12 Lockout InterLock On 13 Airflow Switch On 14 High Fire Switch 15 Flame Detected 16 Flame-Out Timer 17 Main Flame Fail 18 Flame Detected 19 Main Flame Ignition 20 Low Fire Switch Off 21 Running InterLock 22 Lockout InterLock 23 Airflow Switch 24 Call Service 25 Call Service 26 Manual-Open Switch Off 27 Start Switch On 28 Pilot Flame Fail 29 Lockout InterLock 30 Running InterLock 31 Low Fire Switch Off 32 Airflow Switch 33 Pre-ignition InterLock 34 Control On 35 Call Service 36 Call Service 37 Call Service 38 Call Service Siemens Building Technologies, Inc. Page 3 of 10

4 39 Call Service 40 Call Service 41 Main Valve On 42 Pilot Valve 1 On 43 Ignition On 44 Pilot Valve 2 On 45 Low Fire Switch Off 46 Flame Amp Type 47 Jumpers Changed 48 Delayed MV On 49 Man-Open Switch On 50 Jumpers Wrong 51 Flame Too Strong 52 Call Service 53 Lockout Switch 54 Combination Pressure 55 Purge Fan Switch On 56 Block Intake 57 Purge Fan Switch Off Call Service 67 AC Phase 68 Pre-ignition InterLock 69 Call Service 70 Call Service Device Specific Accessory Fault Call Service 128 Poor Flame Sensor Call Service Expanded Annunciator 144 Other Pre-ignition InterLock 145 Valve Closure 146 Other Interlocks 147 Auxiliary Interlock No Auxiliary Interlock No. 4 Page 4 of 10 Siemens Building Technologies, Inc.

5 149 Airflow Switch 150 Low Gas Pressure 151 High Gas Pressure 152 Atomizing Switch 153 Low Oil Temperature 154 High Oil Temperature 155 Low Oil Pressure 156 High Oil Pressure 157 Both Fuels Select 158 Fuel Select Off 159 Auxiliary Limit No High Limit 161 Low Water Cut Off 162 Auxiliary Limit #2 163 Auxiliary Limit #1 164 Other Interlocks 165 Auxiliary Interlock No Auxiliary Interlock No Airflow Switch 168 Low Gas Pressure 169 High Gas Pressure 170 Atomizing Switch 171 Low Oil Temperature 172 High Oil Temperature 173 Low Oil Pressure 174 High Oil Pressure 175 Both Fuels Select 176 Fuel Select Off 177 Auxiliary Limit #3 178 High Limit 179 Low Water Cut Off 180 Auxiliary Limit No Auxiliary Limit No Other Interlocks 183 Auxiliary Interlock No. 5 Siemens Building Technologies, Inc. Page 5 of 10

6 184 Auxiliary Interlock No Airflow Switch 186 Low Gas Pressure 187 High Gas Pressure 188 Atomizing Switch 189 Low Oil Temperature 190 High Oil Temperature 191 Low Oil Pressure 192 High Oil Pressure 193 Both Fuels Select 194 Fuel Select Off 195 Auxiliary Limit No High Limit 197 Low Water Cut Off 198 Auxiliary Limit No Auxiliary Limit No Other Interlocks 201 Auxiliary Interlock No Auxiliary Interlock No Airflow Switch 204 Low Gas Pressure 205 High Gas Pressure 206 Atomizing Switch 207 Low Oil Temperature 208 High Oil Temperature 209 Low Oil Pressure 210 High Oil Pressure 211 Both Fuels Select 212 Fuel Select Off 213 Auxiliary Limit No High Limit 215 Low Water Cut Off 216 Auxiliary Limit No Auxiliary Limit No Other Interlocks Page 6 of 10 Siemens Building Technologies, Inc.

7 219 Auxiliary Interlock No Auxiliary Interlock No Airflow Switch 222 Low Gas Pressure 223 High Gas Pressure 224 Atomizing Switch 225 Low Oil Temperature 226 High Oil Temperature 227 Low Oil Pressure 228 High Oil Pressure 229 Both Fuels Select 230 Fuel Select Off 231 Auxiliary Limit No High Limit 233 Low Water Cut Off 234 Auxiliary Limit No Auxiliary Limit No Other Interlocks 237 Auxiliary Interlock No Auxiliary Interlock No Airflow Switch 240 Low Gas Pressure 241 High Gas Pressure 242 Atomizing Switch 243 Low Oil Temperature 244 High Oil Temperature 245 Low Oil Pressure 246 High Oil Pressure 247 Both Fuels Select 248 Fuel Select Off 249 Auxiliary Limit No High Limit 251 Low Water Cut Off 252 Auxiliary Limit No. 2 Siemens Building Technologies, Inc. Page 7 of 10

8 253 Auxiliary Limit No Other Pre-ignition InterLock 255 Valve Closure Table 3. Sequence State. Sequence State 0 Unused History 1 Initiate 2 Initiate Hold: AC Frequency/Noise 3 Initiate Hold: AC Line Dropout 4 Initiate Hold: AC Frequency 5 Initiate Hold: Low Line Voltage 6 Standby 7 Standby Hold: Remote Control 8 Standby Hold: Start Switch 9 Standby Hold: F/G Flame Detected 10 Standby Hold: T20 Pre-ignition Lock 11 Standby Hold: T7 Running Interlock 12 Standby Hold: T7 Lockout Interlock 13 Standby Hold: Airflow Switch 14 PurgeHold:T19HighFireSwitch 15 Purge Delay: T19 High Fire Jumprd 16 Purge Hold: Test Run/Test Switch 17 Purge Delay: T18 Low Fire Jumprd 18 Purge Hold: F/G Flame Detected 19 Purge 20 PurgeHold:T18LowFireSwitch 21 Purge Hold: T7 Running Interlock 22 Purge Hold: Lockout Interlock 23 Purge Hold: Airflow Switch 24 Purge Hold: Start Switch 25 Pilot Ignition 26 Pilot Hold: Test Run/Test Switch 27 Pilot Hold: StartSwitch 28 Main Ignition 29 Main Ignition Hold: Manual-Open Switch Page 8 of 10 Siemens Building Technologies, Inc.

9 Table 3. Sequence State. (continued) Sequence State 30 Run 31 Run Pilot Valve Hold: Low Fire Switch 32 Pilot Valvehold Ignition 33 Pilot Valve Hold: Pilot Valve Hold Switch 34 Run/Lowfire: Test Run/Test Switch 35 Postpurge 36 State Reset/Alarm Test 38 Safe Start Check 39 Safety Safety Safety Safety Safety Blank 45 Pre-ignition 46 Safety 1 47 Pilot Stab. 48 Main Trial 49 Main Trial 50 Standby Hold: Test Run/Test Switch 51 State State Safety 1: Test Run/Test Switch 54 State Standby Hold: Purge Fan Switch 56 State Purge Hold: Purge Fan Switch 58 State State State State State State State 67 Siemens Building Technologies, Inc. Page 9 of 10

10 Table 3. Sequence State. (continued) Sequence State 65 State State Initiate Hold: AC Phase Error 68 Standby Hold: Pre-ignition Lock 69 State State Burner Off: T6 Burner Switch 72 Standby Hold: T6 Ea Hold Message 73 Standby Hold: T6 Circuit Fault Expanded Annuciator 74 Standby Hold 75 Purge Hold 76 Pilot Hold 77 Main Ignition Hold 78 Run Hold 79 Postpurge Hold 80 Pre-ignition Hold Information in this document is based on specifications believed correct at the time of publication. The right is reserved to make changes as design improvements are introduced. Product or company names mentioned herein may be the trademarks of their respective owners Siemens Building Technologies, Inc. Siemens Building Technologies, Inc Deerfield Parkway Country of Origin: US Buffalo Grove, IL Page10of10 U.S.A.