SVENSK STANDARD SS-EN 488

Size: px

Start display at page:

Download "SVENSK STANDARD SS-EN 488"

Beatrix Wiggins
6 years ago
Views:

SVENSK STANDARD SS-EN 488 Fastställd 2003-02-28 Utgåva 2 Fjärrvärmesystem Förisolerade rörsystem med fast förband mellan värmeisolering och medierör respektive mantelrör för direkt markförlagd

1 SVENSK STANDARD SS-EN 488 Fastställd Utgåva 2 Fjärrvärmesystem Förisolerade rörsystem med fast förband mellan värmeisolering och medierör respektive mantelrör för direkt markförlagd distribution av hetvatten Ventilenhet med ventil av stål för sammanfogning med medierör av stål och med värmeisolering av hård uretancellplast (PUR-skum) och ytterhölje av etenplast District heating pipes Preinsulated bonded pipe systems for directly buried hot water networks Steel valve assembly for steel service pipes, polyurethane thermal insulation and outer casing of polyethylene ICS ; Språk: engelska Publicerad: april 2003 Copyright SIS. Reproduction in any form without permission is prohibited.

2 Europastandarden EN 488:2003 gäller som svensk standard. Detta dokument innehåller den officiella engelska versionen av EN 488:2003. The European Standard EN 488:2003 has the status of a Swedish Standard. This document contains the official English version of EN 488:2003. Dokumentet består av 18 sidor. Upplysningar om sakinnehållet i standarden lämnas av SIS, Swedish Standards Institute, tel Standarder kan beställas hos SIS Förlag AB som även lämnar allmänna upplysningar om svensk och utländsk standard. Postadress: SIS Förlag AB, STOCKHOLM Telefon: Telefax: E-post: sis.sales@sis.se. Internet:

3 EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM EN 488 February 2003 ICS Supersedes EN 488:1994 English version District heating pipes - Preinsulated bonded pipe systems for directly buried hot water networks - Steel valve assembly for steel service pipes, polyurethane thermal insulation and outer casing of polyethylene Tuyaux de chauffage urbain - Systèmes bloqués de tuyaux préisolés pour les réseaux d'eau chaude enterrés directement - Robinets préisolés pour tubes de service en acier, isolation thermique en polyuréthane et tube de protection en polyéthylène Fernwärmerohre - Werkmäßig gedämmte Verbundmantelsysteme für direkt erdverlegte Fernwärmenetze - Vorgedämmte Absperrarmaturen für Stahlmediumrohre mit Polyurethan-Wärmdämmung und Außenmantel aus Polyethylen This European Standard was approved by CEN on 28 November CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Slovak Republic, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG Management Centre: rue de Stassart, 36 B-1050 Brussels 2003 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 488:2003 E

4 EN 488:2003 (E) Provläsningsexemplar / Preview Contents Foreword...4 Introduction Scope Normative references Terms and definitions Requirements Steel parts General requirements for valves Pressure ratings for valves Service temperatures for valves Steel service pipes Welding ends on valves Resistance to bending and axial forces Leak-tightness of valves Fusion welding of steel Casing Polyurethane rigid foam insulation (PUR) Valve assembly Ends of valve assembly End of stem construction Requirements for polyethylene welding Leak-tightness of the welded casing Increase in diameter of the casing pipe Minimum insulation thickness Tolerances on the main dimensions Test methods General Test specimens Steel parts Constructional testing of valves Leak-tightness test of valves Testing of steel welds Casing Polyurethane rigid foam insulation Valve assembly Marking General Steel valve Casing Valve assembly Installation and maintenance...12 Annex A (informative) Guidelines for inspection and testing...13 A.1 Manufacturer s type test...13 A.2 Manufacturer s quality surveillance...13 A.3 External inspection...13 A.4 Extent of inspection...13 A.5 Manufacturer s responsibility...13 page 2

5 EN 488:2003 (E) Annex B (informative) Guideline for installation of valves...15 Bibliography

6 EN 488:2003 (E) Provläsningsexemplar / Preview Foreword This document (EN 488:2003) has been prepared by Technical Committee CEN/TC 107 "Prefabricated district heating pipe systems", the secretariat of which is held by DS. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by August 2003, and conflicting national standards shall be withdrawn at the latest by August This document supersedes EN 488:1994. Annexes A and B are informative. This document includes a Bibliography. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound implement this European Standard: Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Slovakia, Spain, Sweden, Switzerland and the United Kingdom. 4

7 EN 488:2003 (E) Introduction The first edition of EN 488 was approved in The main areas of the revision are: the title has been amended by District heating pipes ; the term underground has been changed to directly buried ; the mentioning in the foreword of the production method injected (poured) has been deleted; two notes concerning commonly used types of valves and rules for calculation of loads and stresses in valve assemblies have been added to the scope; service pipes with nominal diameters from DN 700 up to and including DN 1200 have been added and the requirements have been amended accordingly; through the reference to EN 448 casings with nominal outside diameters from 900 mm up to and including 1400 mm have been added and the requirements have been amended accordingly; through the reference to EN 448 the requirements for polyethylene welding have been changed. This specification is part of the standards for bonded systems using polyurethane foam thermal insulation applied to bond to a steel service pipe and a polyethylene casing. For information on the minimum expected thermal life with operation at various temperatures with respect to PUR foam performance see EN 253:2003, annex B. The other standards from TC 107 are: EN 253:2003, District heating pipes Preinsulated bonded pipe systems for directly buried hot water networks Pipe assembly of steel service pipe, polyurethane thermal insulation and outer casing of polyethylene. EN 448:2003, District heating pipes Preinsulated bonded pipe systems for directly buried hot water networks Fitting assemblies of steel service pipes, polyurethane thermal insulation and outer casing of polyethylene. EN 489:2003, District heating pipes Preinsulated bonded pipe systems for directly buried hot water networks Joint assembly for steel service pipes, polyurethane thermal insulation and outer casing of polyethylene. EN 13941:2003, Design and installation of preinsulated bonded pipe systems for district heating. NOTE The following draft in connection with the above mentioned is under development: pren 14419, District heating pipes Preinsulated bonded pipe systems for directly buried hot water networks Surveillance systems. 5

8 EN 488:2003 (E) Provläsningsexemplar / Preview 1 Scope This European Standard specifies requirements and test methods for valves of prefabricated thermally insulated valve assemblies comprising a steel valve, rigid polyurethane foam insulation and an outer casing of polyethylene for use in directly buried hot water networks with preinsulated pipe assemblies in accordance with EN 253. This standard applies only to insulated valve assemblies for continuous operation with hot water at various temperatures in accordance with clause 1 of EN 253:2003. Guidelines for quality inspection are given in annex A of this standard. Guidelines for installation of valves are given in annex B of this standard. NOTE 1 NOTE 2 For this application the following valve types are commonly used: ball valves, gate valves, and butterfly valves. This standard does not include rules for calculation of loads and stresses. 2 Normative references This European Standard incorporates by dated or undated reference, provisions from other publications. These normative references are cited at the appropriate places in the text, and the publications are listed hereafter. For dated references, subsequent amendments to or revisions of any of these publications apply to this European Standard only when incorporated in it by amendment or revision. For undated references the latest edition of the publication referred to applies (including amendments). EN 19, Industrial valves Marking of metallic valves. EN 253:2003, District heating pipes Preinsulated bonded pipe systems for directly buried hot water networks Pipe assembly of steel service pipe, polyurethane thermal insulation and outer casing of polyethylene. EN 448:2003, District heating pipes Preinsulated bonded pipe systems for directly buried hot water networks Fitting assemblies of steel service pipes, polyurethane thermal insulation and outer casing of polyethylene. EN 736-1, Valves Terminology Part 1: Definition of types of valves. ISO 5208:1993, Industrial valves Pressure testing of valves. 3 Terms and definitions For the purposes of this European Standard, the terms and definitions given in EN 253:2003 and EN 448:2003 apply. For definition of types of valves see EN Requirements 4.1 Steel parts General requirements for valves The valve body shall be fully welded. Flanged or screwed connections shall not be used. The design of the valve shall make it possible to operate the valve outside the insulation. 6

SVENSK STANDARD SS-EN 253/A1:2005

SVENSK STANDARD SS-EN 253/A1:2005 Fastställd 2005-12-01 Utgåva 1 Fjärrvärmesystem Förisolerade rörsystem med fast förband mellan värmeisolering och medierör respektive mantelrör för direkt markförlagd