Fire Safety. Installation Instructions. Model RCC-2/R and RSE-1 Remote Control Centers OPERATION INTRODUCTION INSTALLATION
|
|
- Vivian Austin
- 6 years ago
- Views:
Transcription
1 Fire Safety Installation Instructions Model RCC-/R and RSE- Remote Control Centers INTRODUCTI The SIEMENS Model RCC-/R Remote Command Center (See Figure ) provides the option to remotely annunciate and control MXL and MXL-IQ system status. The RCC-/R and RSE- provide for mounting and control of the PIM- printer interface module. The following modules come already installed in an RCC-/R: Keypad LCD Display ANN- Driver Board PS-5N7 Power Supply The following modules come already installed in an RSE-: ANN- Driver Board PS-5N7 Power Supply The RCC-/R has a mounting location for an optional PIM-. The RSE- has the same mounting and requires the PIM-. The RCC-/R comes with a clear lens on a secure door. This limits access to the control of the system or the display. The door is secured with a T-5 lock set. OPERATI The keypad on the RCC-/R operates the same as the MKB in the MXL enclosure. See Section of the MXL Installation, Operation and Maintenance Manual, P/N , for the complete operating instructions for the control panel. INSTALLATI Always remove all power before installation, first the battery and then the AC. Setting the Network Address Before installing the RCC/RSE, set the network address on S-SW and S-SW of the ANN- board. Refer to Table for switch settings. (See also Setting the Network Address in Section, INSTALLATI of the MXL/MXLV Manual, P/N ) SWITCH S-SW TABLE SWITCH SETTINGS THE ANN- ADDRESS SETTINGS FOR: On S-SW S-SW S-SW S-SW5 Figure RCC-/R Remote Command Center Siemens Building Technologies, Inc. 8 Fernwood Road Florham Park, New Jersey 079 NOTE: Switches S-SW and S-SW are for future use. Switch S-SW5 is used to select supervision. Siemens Building Technologies, Ltd. Kenview Boulevard Brampton, Ontario L6T 5E CN P/N
2 Setting Supervision Use switch S-SW5 on the ANN- to select or deselect supervision. If your ANN- has a switch with position indicated on the left-hand side, ignore the printing on the switch. SW on S is at the extreme right-hand side of S, regardless of any other marking. To set for supervision S-SW5 = Closed () To set for non-supervision S-SW5 = Open () NOTE: When you select non-supervision for an annunciator, there must also be one and only one supervised annunciator at the same address. Mounting Before mounting the RCC/RSE, follow these steps:. Remove the cover assembly from the backbox.. Disconnect at P the cable from the PS-5N7.. Remove the PS-5N7 from the backbox (See Figures and ).. Set the panel to one side. Consider the following when mounting the backbox: Mounting height for visual and manual access to the keypad Weight and size of the enclosure Local mounting codes To mount the RCC/RSE, follow these steps:. Fasten the RCC/RSE backbox securely to a clean, dry, shock-free, and vibration-free surface using the four mounting holes provided. (Refer to Figure for the dimensions of the backbox and the location of the mounting holes.) Position the RCC/ RSE backbox clear of obstructions so that the door opens freely and the indicators and controls are easily accessible.. Pull all field wiring into the backbox and dress the wiring to the approximate location to which it will go. Install field wiring to the PS-5N7 (Refer to PS-5N7 Installation Instructions, P/N ).. If a PIM- is required, mount it to the set of four standoffs to the right of the PS-5N7 (See Figures and ). Connect P on the PIM- to P on the ANN-, using the inch cable, P/N Connect P on the PIM- to P on the PS-5N7, using the inch cable, P/N (Refer to PS-5N7 Installation Instructions, P/N , PIM- Installation Instructions, P/N and Figure 6).. If a PIM- is not installed, reconnect P on the ANN- to P on the PS-5N7. 5. Reattach the cover assembly to the backbox. 6. Refer to the MXL/MXLV Manual, P/N , for additional information on the operation of the keypad. ELECTRICAL RATINGS RCC/RSE: 8- VDC, 80mA max Battery current: 75mA RCC/RSE with PIM-: 8- VDC, 00mA max Battery current: 95mA WIRING Refer to the following Installation Instructions as needed: MMB- P/N MMB- P/N PSR- P/N PS-5 P/N PLM-5 P/N PAD- P/N SMB- P/N MXL/MXLV Manual P/N
3 PS-5N7 COVER LCD DISPLAY ANN- RCC-/RSE- BACKBOX PIM- (OPTIAL) ANNUNCIATOR PANEL RCC-/RSE- OUTER DOOR Figure RCC-/R Exploded View PS-5N7 ANN- RSE- BACKBOX PIM- (REQUIRED) RSE- OUTER DOOR Figure RSE- Exploded View
4 NOTE: The RCC/RSE MUST have an earth ground connected to the chassis. Wire shield or conduit is not an acceptable ground. Use any available unused, unpainted stud for chassis grounding. Figure RCC-/R, RSE- Dimensions PSR- TB DO NOT USE DO NOT USE NO EOLR 6 5 TB CHASSIS EOLR 0 OHMS /W, 5% P/N PS-5N7 (INSTALLED IN AN RCC-/RSE- ENCLOSURE) PSR- TB SHIELD MMB- / SMB- NO EOLR EOLR 0 OHMS /W, 5% P/N Notes:. Use a minimum wire gauge of 8 AWG.. Use a maximum of 80 ohms per pair of wires for the network connections.. Use shielded twisted pair for network connections.. Terminate the shield LY at the MMB/SMB enclosure. 5. PSR- only allowed in systems with MMB-. 6. DO NOT place the PS-5N7 at the end of the network (Style 7 only). 7. This configuration is power limited to NFPA 70 according to NEC All wiring supervised. 9. Refer to Wiring Specification for MXL, MXL-IQ and MXLV Systems, P/N revision 6 or higher, for additional wiring information. Figure 5 PS-5N7 Power Supply and Network Wiring Diagram in RCC/RSE Enclosure (Style )
5 CABLE P/N P POWER TO MOM- TB MMB- / SMB- 5 N PSR- P7 FOR NET-7 N ET 7 M E T W O R K TB SHIELD SHIELD CHASSIS P6 TB P TB P5 TB6 P7 CABLE P/N EOLR 0 OHM, /W, 5% P/N P NET-7 MOM- MAKE THIS CNECTI TO ANY OF THE FOLLOWING TERMINATIS: MMB SMB PSR- PLM-5 (Used with PS-5) ALARMSAF (Model AS/PS5-BFS--UL) PAD- TB5, 9- TB5, 9- TB, -6 TB, - TB, and TB, Aux P.S. + VDC - VDC RETURN SUPERVISED POWER LIMITED NETWORK A (PRIMARY) SUPERVISED POWER LIMITED NETWORK B (SECDARY) SUPERVISED POWER LIMITED 5 6 TB PS-5N7 (INSTALLED IN AN RCC-/RSE- ENCLOSURE) RCC- / RSE- Notes:. Use a minimum wire gauge of 8 AWG.. Use a maximum of 80 ohms per pair of wires for the network connections.. Use shielded twisted pair for network connections.. Terminate the shield LY at the MMB/SMB enclosure. 5. PSR- only allowed in systems with MMB-. 6. DO NOT place the PS-5N7 at the end of the network (Style 7 only). 7. This configuration is power limited to NFPA 70 according to NEC Refer to Wiring Specification for MXL, MXL-IQ and MXLV Systems, P/N revision 6 or higher, for additional wiring information. Figure 6 PS-5N7 Power Supply and Network Wiring Diagram in RCC/RSE Enclosure (Style 7) 5
6 Siemens Building Technologies, Inc. 8 Fernwood Road Florham Park, New Jersey 079 Siemens Building Technologies, Ltd. Kenview Boulevard Brampton, Ontario L6T 5E CN P/N
Fire Safety. Installation Instructions Model SMB-2 Main Control Board OPERATION INSTALLATION
Fire Safety Installation Instructions Model SMB- Main Control Board OPERATION The SIEMENS Model SMB- board in each MXL-IQ System controls operations and monitors input device identity, network communication,
More informationFire Safety. Installation Instructions Model MMB-2 Main Control Board OPERATION. INSTALLATION Always remove power before installation.
Fire Safety nstallation nstructions Model MMB- Main ontrol Board OPERATON The SEMENS Model MMB- board in each MXL System controls operations and monitors input device identity, network communication, and
More informationInstallation Instructions Model SSD-C-REM
Installation Instructions Model SSD-C-REM Remote System Status Display with Control ON ALARM SUPERVISORY SECURITY TROUBLE AUDIBLES SILENCED INTRODUCTION The SIEMENS Model SSD-C-REM is an optional FireFinder
More informationFire Safety. Installation Instructions Model NIM-1W Network Interface Module MXL NETWORK INTERFACE APPLICATIONS OPERATION NIM-1W
Fire Safety Installation Instructions Model NIM-W Network Interface Module MXL NETWORK INTERFACE APPLICATIONS OPERATION The SIEMENS Model NIM-W provides a new communication path for the following uses:
More informationFire Safety. Installation Instructions. Model ADBX-11. Audible Base INTRODUCTION. Model ADBX-11
Fire Safety Installation Instructions Model ADBX11 Audible Base INTRODUCTION Model ADBX11 The SIEMENS Model ADBX11 Audible Base consists of a standard Series 11 base combined with an audible device. All
More informationModel PAD-3 Distributed Power Module NAC Expander Installation, Operation, and Maintenance Manual
Fire Safety Model PAD-3 Distributed Power Module NAC Expander Installation, Operation, and Maintenance Manual Siemens Building Technologies, Inc. Siemens Building Technologies, Ltd. 8 Fernwood Road 2 Kenview
More informationAND ARCHITECT SPECIFICATIONS
MXL-IQ Advanced Life Safety System ENGINEER AND ARCHITECT SPECIFICATIONS FirePrint Application Specific Fire Detection Capacity for up to 240 Intelligent Analog Detectors Expandable Up to a Stand Alone
More informationMXL/MXLV 19 Rack Mount Equipment
MXL/MXLV 19 Rack Mount Equipment Models: MXL-RK1, ACM-RK, MKB-RK, MMB-RK, MOM-RK, MPS-RK, TSP-RK, VSM-RK, CABLES-RK, MKB-3 ENGINEER AND ARCHITECT SPECIFICATIONS Standard 19 Rack Mounting for MXL and MXLV
More informationMXL/MXLV Enclosuress & Equipment Models: MME-3, MBR-MP, MLE-6, MBR-3MP, MDL-1, MDB-1, MDG-1, MHD-1, MHD-2, MHD-3, MHD-4
MXL/MXLV Enclosuress & Equipment Models: MME-3, MBR-MP, MLE-6, MBR-3MP, MDL-1, MDB-1, MDG-1, MHD-1, MHD-2, MHD-3, MHD-4 ENGINEER AND ARCHITECT SPECIFICATIONS Enclosure & Door Package (MME-3) Standard Size
More informationFire Safety. Installation Instructions Model PSR-1 Remote Power Supply INTRODUCTION. Figure 1 PSR-1 Remote Power Supply
Fire Safety Installation Instructions Model PSR- Remote Power Supply Figure PSR- Remote Power Supply INTRODUCTION The SIEMENS Model PSR- (See Figure ) is a microprocessor controlled remote power supply
More informationOperating Instructions MXL Multi-Line Keyboard/Display Panel
Operating Instructions MXL Multi-Line Keyboard/Display Panel Local Mode Operation TRODUCTION When the MXL Keyboard/Display Panel is installed in a control panel, the components are behind a locked door.
More informationAdvanced Protection System
MXL-IQ Advanced Protection System FirePrint Application Specific Detection Capacity for up to 240 Intelligent Analog Detectors Expandable Up to a Stand Alone System Capacity of 998 Input and Output Points
More informationInstallation Instructions Model HZM
Installation Instructions Model Remote Conventional Zone Module INTRODUCTION The Model from is an intelligent device that connects a single zone of conventional devices to a DLC (FireFinder-XLS System)
More informationInstallation Instructions Model DLC
Installation Instructions Model DLC Device Loop Card INTRODUCTION OPERATION The SIEMENS Model DLC Device Loop Card is the interface for connection of FireFinder-XLS smoke detectors, manual stations, monitor
More informationData Sheet Fire Safety & Security Products. System Overview. Initiating Circuits SXL-EX FACP 7906
s Data Sheet Fire Safety & Security Products SXL-EX Fire Alarm Control Panel Conventional Zone Fire Alarm Control Panel ARCHITECT AND ENGINEER SPECIFICATIONS Four (4) zones expandable to eight (8) zones
More informationFire Safety. Installation Instructions Model D2300CPS Fiber Optic Interface INTRODUCTION MOUNTING ELECTRICAL CONNECTIONS. Figure 1 D2300CPS Module
Fire Safety Installation Instructions Model Fiber Optic Interface INTRODUCTION The Model from Siemens uilding Technologies, Inc. (See Figure 1) is a Fiber Optic interface for the MXL s RS-485 network (MNET
More information08 Series Notification Appliances AS / AH & AS Audible Strobe Appliances and AH Audibles Application: Indoor / Outdoor
s Data Sheet Fire Safety & Security Products 08 Series Notification Appliances AS / AH & AS Audible Strobe Appliances and AH Audibles Application: Indoor / Outdoor AS-MC-CW AS-MC-R AH-W AH-R Product Overview
More informationRM-1 Series. Remote Microphones. (RM-1, RM-1SA) Document Revision B RM-1 RM-1SA. RM-1 on ADP-4 dress panel. RM-1SA in a CAB-RM or CAB-RMR
This product has been certified to comply with the requirements in the Standard for Control Units and Accessories for Fire Alarm Systems, UL 864 9th Edition. The following products have not received UL
More informationMXL-IQ CONTROL PANEL. Operation, Installation, and Maintenance Manual. Siemens Industry, Inc. Building Technologies Division Florham Park, NJ
MXL-IQ CONTROL PANEL Operation, Installation, and Maintenance Manual Siemens Industry, Inc. Building Technologies Division Florham Park, NJ P/N 315-093624-13 Siemens Building Technologies, Ltd. Fire Safety
More informationInstallation Instructions Model MDACT MXL/FireFinder-XLS Multi-Point Digital Alarm Communicator
Installation Instructions Model MDACT MXL/FireFinder-XLS Multi-Point Digital Alarm Communicator INTRODUCTION The Model MDACT from Siemens Industry, Inc. is a multipoint serial dialer for use in MXL and
More informationANNUNCIATOR FIXED MODULE
12 Clintonville Road Northford, CT 06472 Phone: 203-484-7161 Fax: 203-484-7118 THE ANNUNCIATOR FIXED MODULE Installation Manual for the AFM-16ATF and AFM-32AF Annunciator Modules Document # 15970 3/27/95
More informationMMF Six Zone Interface Module
Installation and Maintenance Instructions I56-900-005 MMF-0-6 Six Zone Interface Module SPECIFICATIONS Normal Operating Voltage: 5- VDC Stand-By Current: ma Alarm Current: 40 ma (assumes all six LEDs solid
More informationSPEC SHEET. Simple Expansion Solutions ZONE EXPANSION MODULES: SINGLE AND MULTIPLE POINT
SPEC SHEET Simple Expansion Solutions Expand your DMP panel options with a wide array of expansion modules. Add supervised Class B burglary zones. Connect non-powered burglary or fire type devices for
More informationInstallation Instructions Model CDC-4
Installation Instructions CDC-4 Conventional Card INTRODUCTION The SIEMENS CDC is a card that allows conventional detectors to be used on the FireFinder-XLS system. It provides four Class or Class B conventional
More informationIDP-Zone-6 Six Zone Interface Module
INSTALLATION AND MAINTENANCE INSTRUCTIONS IDP-Zone-6 Six Zone Interface Module BEFORE INSTALLING If the modules will be installed in an existing operational system, inform the operator and local authority
More informationBooster Power Supply Manual
Supply Manual DEVELOPED BY COPYRIGHT NOTICE General Signal Building Systems Corporation 6411 Parkland Drive Sarasota, FL 34243 (941) 739-4300 Copyright 1999 General Signal Building Systems Corporation
More informationLDM Series Lamp Driver Modules For Graphic Annunciation and Control
12 Clintonville Road Northford, CT 06472 (203) 484-7161 FAX: (203) 484-7118 LDM Series Lamp Driver Modules For Graphic Annunciation and Control Used with the System 500, System 5000, AM2020/AFP1010 and
More informationSC-6 Six Supervised Control Module
INSTALLATION AND MAINTENANCE INSTRUCTIONS SC-6 Six Supervised Control Module SPECIFICATIONS Normal Operating Voltage: Stand-By Current: Alarm Current: Temperature Range: Humidity: Dimensions: Accessories:
More informationTYPE C: RETURN AIR UNDER POSITIVE PRESSURE FROM SEPARATE BLOWER
Installation Instructions Model AD-HR Air Duct Monitoring Housing INTRODUCTION The SIEMENS Model AD-HR is a sampling tube, air duct monitoring housing. When used with a compatible smoke detector, smoke
More information'08 Series Notification A liances
SIEMENS Data Sheet Fire Safety & Security Products '08 Series Notification A liances AS I AH & AS - Audible Strobe Appliances and AH Audibles AS-MC-CW AS-MC-R AH-W AH-R Product Overview - Fast installation
More informationAddressable NAC Output Module D327A
Installation Instructions Notice Addressable NAC Output Module D327A These instructions cover the installation of the D327A Addressable NAC Output Module in an analog system controlled by a Bosch D8024,
More informationHarrington Signal HS-3100/3200 Fire Alarm Control Unit
HARRINGTON SIGNAL INC. FIRE ALARM Harrington Signal HS-3100/3200 Fire Alarm Control Unit Installation Manual Revision 2 January 2009 Document # LT-2000HAR Table of Contents 1.0 Technical Information...
More informationAir Duct Housings. Description
Air Duct Housings Series IL, and Series 3 Ionization or Photoelectric Detectors Optional Relays for Supplementary Equipment Operation Optional Control Module for Self-contained Operation (Series 3 Detectors
More information* These Remote Mics must be SPRM-GP
273 Branchport Avenue Long Branch, NJ 07740 (800) 6312148 Thank you for using our products. www.coopernotification.com INSTALLATION INSTRUCTIONS REMOTE MICROPHONE EXPANSION MODULE Use this product according
More information1 UL 864 Compliance. 2 Product Overview. Network Communications Module NCM-W/F Product Installation Document. 1.1 Products Subject to AHJ Approval
1 UL 864 Compliance 12 Clintonville Road Northford, CT 06472-1653 USA 203-484-7161 FAX 203-484-7118 www.notifier.com Network Communications Module NCM-W/F Product Installation Document PN 51533:D2 04/13/2012
More information30.45 Electric Release PDRP-2001
The PDRP-2001 Fire Alarm Control Panel (FACP) is a six-zone control panel for single and dual hazard deluge and preaction applications. The FACP is compatible with conventional input devices (2-wire or
More informationGeneral Routing Interface
General Routing Interface Features The General Routing Interface Card is an optional module to provide Fire and Fault Routing Outputs compliant with BSEN54-2: 1998 Clauses 7.9 and 8.9 and BS5839-1: 2002.
More informationPS6 SERIES. Installation PS6 SERIES. Power Supplies c/w Fire Panel Interface, EOL Trigger and Standby Power Option
Installation PS6 SERIES Power Supplies PS6 SERIES Power Supplies c/w Fire Panel Interface, EOL Trigger and Standby Power Option Installation and Specifications Manual ISDPS6_SERIES 08121590 PCN15016 R05/15GR
More information4100U City and Relay Cards Installation Instructions
4100U City and Relay Cards Installation Instructions Introduction This publication describes the installation procedure for the following: 4100-6031/6032 City Circuit Cards 4100-6033 Alarm Relay Card Inspecting
More informationTruPortal Wireless Locks Quick Reference
TruPortal Wireless Locks Quick Reference en-us Introduction This document describes how to connect the following wireless locks to TruPortal hardware: Schlage AD-400, which connects to TruPortal hardware
More informationCerberus TM PRO Fire Safety System A comprehensive fire-protection system
s Data Sheet Fire Safety & Security Products Cerberus TM PRO Fire Safety System A comprehensive fire-protection system Standard 50-point, 252-point and 504-point-capacity systems Remote viewing for the
More informationMODUL-R FIRE ALARM CONTROL PANELS. MR-2900/MR-2920 Addressable Fire Alarm Control Panels MEA. Features. Description
MODUL-R FIRE ALARM CONTROL PANELS MR-2900/MR-2920 Addressable Fire Alarm Control Panels Description MR-2900 Fire Alarm Control Panel The MR-2900 fire alarm system control unit is the heart of a sophisticated
More informationCZ-6A Six Zone Interface Module
INSTALLATION AND MAINTENANCE INSTRUCTIONS CZ-6A Six Zone Interface Module 658 Kitimat Rd. Unit #6 Mississauga, Ontario L5N T5-800-SENSOR, FAX: 905-8-077 www.systemsensor.ca SPECIFICATIONS Normal Operating
More informationPublic Safety DAS Annunciator Panel
Public Safety DAS Annunciator Panel 120 VAC Models: 1221-A, 1221-B, 1221-C Revision D 91117 48 VDC Models: 1221-A-48, 1221-B-48, 1221-C-48 24 VDC Models: 1221A-24, 1221-B-24, 1221-C-24 CAUTION: (Read This
More informationMultiplex Eight Input Remote Modules
Multiplex Eight Input Remote Modules 1.0 Introduction These instructions cover the installation of the D7042/D7042B Eight Input Remote Modules in a fire system supervised by an FPD-7024 Fire Alarm Control
More informationRPSMLR2 RPSMLR2BB. Panic Device Power Controller Installation Guide LISTED. Rev
RPSMLR2 RPSMLR2BB Panic Device Power Controller Installation Guide LISTED Rev. 102715 Overview: RPSMLR2BB, RPSMLR2 will operate up to two (2) 24VDC panic hardware devices simultaneously. It is designed
More informationThese instructions detail procedures to follow in order to avoid damage to equipment.
D326A, D334A, D339A Point Contact Modules Installation Guide 1.0 Notice These instructions are for the installation of the D326A, D334A and D339A Point Contact Modules in an analog system controlled by
More informationMS-4012/4024 and CMS-4012/4024. Instruction Manual for the. Fire Alarm Control Panels
R 12 Clintonville Road, Northford, CT 06472 Phone: (203) 484-7161 FAX: (203) 484-7118 Instruction Manual for the MS-4012/4024 and CMS-4012/4024 Fire Alarm Control Panels Document 15586 5/11/93 Revision:
More informationFireNET Plus Wiring Instructions
FireNET Plus Wiring Instructions This manual provides wiring instructions for the 1 loop and 2 loop version of the FireNET Plus panels, which supports our finest Hochiki s DCP protocol. Note: Refer to
More information- 4 12VDC or 24VDC VDC or 24VDC - Eight (8) Fused Outputs - Eight (8) PTC Outputs. Installing Company: Service Rep.
140 58th St. Brooklyn, NY Power Supply/Chargers Installation Guide Models Include: eflow4n/eflow4nx - 4 amp @ 12VDC or 24VDC eflow4n8/eflow4nx8 eflow4n8d/eflow4nx8d - 4 amp @ 12VDC or 24VDC - 4 amp @ 12VDC
More informationInstallation Instructions Model ABHW-4S
Installation Instructions Model ABHW-4S Intelligent Audible Base for Sleeping Area with 520Hz Low Frequency Sounder Introduction Application note The Model ABHW-4S audible base from Siemens Industry, Inc.
More informationMarine Fire Detection System Manual MXL Control Panel
Marine Fire Detection System Manual MXL Control Panel US Coast Guard Approved Certificate No. (Cert No:6.002/22/7) Reference ULI File No. S522 Siemens Building Technologies, Inc. Fire Safety 8 Fernwood
More informationRMS/RPX Reader. User Manual
RMS/RPX Reader User Manual Copyright Disclaimer Trademarks and patents Intended use FCC compliance Copyright 2005, GE Security Inc. All rights reserved. This document may not be copied or otherwise reproduced,
More informationADEMCO 4208SNF V-Plex Universal Class A Module INSTALLATION AND SETUP GUIDE
K3179V2 2/11 Rev. A ADEMCO 4208SNF V-Plex Universal Class A Module INSTALLATION AND SETUP GUIDE FEATURES The ADEMCO 4208SNF Universal Class A Module can be used in either of two different applications.
More informationDesigo TM Fire Safety System A comprehensive fire-protection system
s Desigo TM Fire Safety System A comprehensive fire-protection system Standard 50-point, 252-point and 504-point-capacity systems Remote viewing for the 252- point and 504-point systems One (1) or (2)
More informationSP-1000X. Panic Device Power Controller Installation Guide. Rev
TM SP-1000X Panic Device Power Controller Installation Guide Rev. 120213 Overview: SP-1000X will operate up to two (2) 24VDC panic hardware devices simultaneously. It is designed to handle the high current
More informationMultiple Input and Output Modules
Kingfisher Company, inc. Multiple Input and Output Modules Features: Removable 12 to 18 AWG plug-in terminal blocks Individual LED indicators Unused addresses may be disabled Rotary address switches Class
More informationMOUNTING DETAILS. Mounting Matrix / Details ENGINEER AND ARCHITECT SPECIFICATIONS CATALOG SHEET. 2-1/8 Deep
MOUNTING DETAILS Mounting Matrix / Details (a) universal mounting plate ENGINEER AND ARCHITECT SPECIFICATIONS (e) 4 square, deep, flush (bo) 2-1/8 Deep AS Mounting (item included with AS series devices)
More informationFireSeeker Fire Alarm Control Panel Model FS-100 Installation, Operation, and Maintenance Manual
Fire Safety FireSeeker Fire Alarm Control Panel Model FS-100 Installation, Operation, and Maintenance Manual Siemens Building Technologies, Inc. Siemens Building Technologies, Ltd. 8 Fernwood Road 2 Kenview
More informationACC-25/50ZST. Zoned System Voice with Telephone Evacuation Control Panel
ACC-25/50ZST Zoned System Voice with Telephone Evacuation Control Panel General The AUDIO COMMAND CENTER 25/50 Zone System with FireFighters Telephone (ACC-25/50ZST) is a state-of-the-art Emergency Voice
More informations Notification Appliances
s Notification Appliances Data Sheet Fire Safety Products AS & AH Audible Horn Strobe / Audible Horn Appliances Application: Indoor / Outdoor AS-MC-CW AS-MC-R AH-R AH-W Product Overview Fast installation
More informationFireSeeker Fire Alarm Control Panel Model FS-250 Installation, Operation and Maintenance Manual
FireSeeker Fire Alarm Control Panel Model FS-250 Installation, Operation and Maintenance Manual P/N 315-049353-1 Siemens Building Technologies Fire Safety TABLE OF CONTENTS INTRODUCTION... 1 CONTROL PANEL
More informationRemote NAC Power Supply D7038
Operation and Installation Guide Remote NAC Power Supply D7038 D7038 REMOTE NAC POWER SUPPLY Page 2 2005 Bosch Security Systems Contents Contents 1.0 Overview...5 1.1 Module Control...5 1.1.1 Option Bus
More informationModels NFPA 1221-A, NFPA 1221-B Public Safety DAS Annunciator Panel. Revision E 61117
Models NFPA 1221-A, NFPA 1221-B Public Safety DAS Annunciator Panel Revision E 61117 CAUTION: (Read This First) This panel has been designed to make it nearly bullet proof to mistakes made when wiring
More informationHARDwired Installation/ Owner s Manual
HARDwired Installation/ Owner s Manual Use this manual for circuit - Revision L or higher. For Models:,, and Multi-Door Access Controller Wiegand Compatable --R-- Provides Access Control System to manage
More informationThe ACM-8R Annunciator Control Module
12 Clintonville Road Northford, CT 06472 203-484-7161 FAX: 203-484-7118 The Annunciator Control Module For the System 500, System 5000, AFP-200, AM2020, AFP1010 and SFP-1024 Fire Alarm Control Panels Document
More informationFire Safety. Installation Instructions Model CSM-4 Controllable Signal Module OPERATION INSTALLATION
Fire Safety Installation Instructions Model SM- ontrollable Signal Module OPERATIO The Model SM- ontrollable Signal Module has two fully supervised, programmable circuits. The outputs supply two lass B
More informationACSI AO ELECTRIC LATCH RETRACTION CONTROLLER INSTALLATION INSTRUCTIONS I.D. 1089, REV. F
II 1400-2 ACSI 1406-04-AO ELECTRIC LATCH RETRACTION CONTROLLER INSTALLATION INSTRUCTIONS I.D. 1089, REV. F INSTALLATION Transformer Model BE31763001 by Basler Electric, Transformer Model 2010028 by Galaxy
More informationMGD-32 and AGD-048. Remote Multiplex Graphic Driver Annunciators and Adder Boards. Wiring and Installation Manual
MGD-32 and AGD-048 Remote Multiplex Graphic Driver Annunciators and Adder Boards Wiring and Installation Manual LT-847 Rev. 8 February 2011 Table of Contents Table of Contents 1.0 Introduction 7 1.1 Contact
More informationSHORT CIRCUIT ISOLATOR TO NEXT COMPONENT REQUIRING POWER TO NEXT KEYPAD (** IF REQUIRED) STROBE RELAY MODULE KEYSWITCH ISOLATION MODULE STROBE
The Door Switch 11772 Westline Industrial Drive St. Louis, Mo 63146 (877) 998-5625 www.thedoorswitch.com Patent No. RE42,991 and RE44,039 CONTROL PANEL TRANSFORMER (SUPPLIED WITH CONTROL PANEL) NOTIFICATION
More informationJune 10, 2002 DF C S2424
GENERAL www.firelite.com The Fire Lite FIRE COMMAND 25/50X is a state-of-theart Emergency Voice Evacuation Control Panel (VECP), with significant technological enhancements that set it apart from other
More information20 Light Remote Annunciator
Light Remote Annunciator Owner s Manual Surface Mount Flush Mount 94-95- Standard Annunciator 94-, 94-95-, 95-4- 4- Annunciator w/remote Relay Panel 4-, 4-4-, 4-49-, 49-49-, 49- Time Multiplexed Annunciator
More informationMANUAL RESET ALARM RELEASE
Fire Door Release MODEL AR-D2 MANUAL RESET ALARM RELEASE INSTRUCTION MANUAL AR-D2 GENERAL INFORMATION 1. Review all installation instructions, procedures, cautions and warnings contained within this manual
More informationLamp Driver Module LDM-32F
PN 50055:C0 ECN 01-155 Lamp Driver Module LDM-32F Instruction Manual Document 50055 03/20/2001 Rev: C Fire Alarm System Limitations An automatic fire alarm system typically made up of smoke detectors,
More informationCerberus PRO A comprehensive fire-protection system
Cerberus PRO A comprehensive fire-protection system Cerberus TM ARCHITECT AND ENGINEER SPECIFICATIONS Standard 252-point and 504-point fire systems Remote viewing for the 252- point and 504-point systems
More informationMS Rev. 2/DACT-UD: Intelligent Addressable FACP with Optional 2nd Loop
MS-9600 Rev. 2/DACT-UD: Intelligent Addressable FACP with Optional 2nd Loop DF-52395:A A1-90 Addressable General The Fire Lite MS-9600 is a compact, cost-effective, intelligent addressable fire alarm control
More informationInstallation Instructions Model CAB-BATT/R
Installation Instructions odel CABBATT/R Box INTRDUCTIN The odel CABBATT/R Box from, is used to house BTX2 (55AH) batteries for XL Systems; BTX2 (55AH) batteries and BTX3 (00AH) batteries for FireFinderXLS/Desigo
More informationI NSTALLATION M ANUAL
MR-2900 Fire Alarm Control Unit I NSTALLATION M ANUAL September 2009 Document #: LT-2010 Rev.2 WARNING : This manual contains information on limitations regarding product use and function and information
More informationSIGA-CC1 Single Input Signal Module Installation Sheet
SIGA-CC1 Single Input Signal Module Installation Sheet Personality codes Use the personality codes described below to configure the SIGA-CC1 module. See Table 1 for listing information Table 1: Personality
More informationINSTALLATION INSTRUCTIONS Model FH-2071-UM Enclosure
INSTALLATION INSTRUCTIONS Model FH-2071-UM Enclosure Enclosure INTRODUCTION The Model FH-2071-UM Enclosure from., used in Marine applications is robust and weather-resistant. Its durable design is customized
More informationLED Driver Module. These instructions contain procedures to follow in order to avoid personal injury and damage to equipment.
LED Driver Module Installation Guide 1.0 Notice These instructions are for installing Radionics LED Driver Module in a fire alarm system controlled by Radionics D8024 or D10024 Fire Alarm Control Panels
More informationE340 BOILER CONTROL INSTALLATION MANUAL
E-3451 JUNE 1999 E340 BOILER CONTROL INSTALLATION MANUAL DESCRIPTION The E340 Boiler Room Control is a microprocessor-based Boiler Management System designed to interface with existing Fireye D Series
More informationPOWERPATH PS-8 (105531) PS-8E (100263) PS-6 (105530) PS-6E (100262)
PATH PS-8 (105531) PS-8E (100263) PS-6 (105530) PS-6E (100262) NAC ETENDER SUPPLIES Installation Instructions 273 Branchport Avenue, Long Branch, NJ 07740-6899 Ph: (800) 631-2148 Fax: (732) 222-8707 Web
More informationXP6-C. Six Circuit Supervised Control Module and SYNC-1 Accessory Card
XP6-C Six Circuit Supervised Control Module and SYNC-1 Accessory Card General NOTIFIER s XP6-C six-circuit supervised control module provides intelligent alarm systems with supervised monitoring of wiring
More informationMPC-6000 / MPC-7000 / RND-2
MPC-6000 / MPC-7000 / RND-2 Fire Alarm System Control Unit Installation, Operation and Maintenance Manual Siemens Building Technologies, Inc. 8 Fernwood Road Florham Park, NJ 07932 Tel: (973) 593-2600
More informationInstallation Guide for models:
140 58th St. Brooklyn, NY Access Power Controllers with Power Supplies Installation Guide for models: Maximal11F - Power Supply 1: 12VDC @ 3.3 amp or 24VDC @ 3.6 amp. - Power Supply 2: 12VDC @ 3.3 amp
More informationSeries SPB Audio Boosters Installation, Testing, Operation, and Maintenance Manual
Series SPB Audio Boosters Installation, Testing, Operation, and Maintenance Manual Part Number P84748 Assembly Number A84749 Revision C Revision A Copyright 2006 Printed in U.S.A. All rights reserved.
More informationSLATE. Base Module INSTALLATION INSTRUCTIONS R8001A1001
SLATE Base Module R8001A1001 INSTALLATION INSTRUCTIONS Scan for more information Application SLATE brings configurable safety and programmable logic together into one single platform. The platform can
More informationFireNET Fire Alarm Control Panel Installation Manual
FireNET L@titude Fire Alarm Control Panel Installation Manual Page 2 Contents Contents Contents 3 Glossary 9 Compliance Information 11 Section 1: Introduction 12 Technical Support 12 Return Material Authorization
More informationAND ARCHITECT SPECIFICATIONS
CSM-4 Controllable Signal/Releasing Module ENGINEER AND ARCHITECT SPECIFICATIONS Supervised Alarm Notification Appliance Circuits Operates Audible or Visual Devices Class A (Style Z) or Class B (StyleY)
More informationD326A/D334A/D339A. Installation Instructions. Point Contact Modules
D326A/D334A/D339A EN Installation Instructions Point Contact Modules D326A/D334A/D339A Installation Instructions 1.0 Description Notice Use these instructions to install the D326A, D334A, and D339A Point
More informationPSN-1000 & PSN 1000(E) Installation Manual
PSN-1000 & PSN 1000(E) Installation Manual Potter Electric Signal Company, LLC St. Louis, MO Customer Service: (866) 240-1870 Technical Support: (866) 956-1211 Fax: (314) 595-6999 www.pottersignal.com
More informationANC BBX-FXMNS or BBX Audio Network Controller Board Installation Instructions TNC-5000 ANC Module Mounting Locations
Audio Network Controller Board Installation Instructions Module Mounting Locations The Audio Network Controller board can be mounted in two places. One position is over the Audio Network Controller module
More informationOperation and Installation Guide. Zone Expansion Module D8125
Operation and Installation Guide Zone Expansion Module D8125 Page 2 2004 Bosch Security Systems, Inc. Contents 1.0 Introduction...7 1.1 Guide Organization... 7 1.2 Other Literature Referenced... 7 1.3
More informationAPS-300 SERIES DUAL VOLTAGE UL 294 LISTED ACCESS CONTROL POWER SUPPLIES
APS-300 SERIES DUAL VOLTAGE UL 294 LISTED ACCESS CONTROL POWER SUPPLIES POWER SUPPLY AND BATTERY CHARGER AC AND DC STATUS INDICATORS ENOUGH POWER TO SUPPORT UP TO 3 MAGLOCKS OR ELECTRIC STRIKES PLUS REQUIRED
More informationPFC-4064 Conventional Fire Alarm Panel
PFC-4064 Conventional Fire Alarm Panel Installation, Operations & Programming Manual Potter Electric Signal Company, LLC St. Louis, MO Customer Service: (866) 240-1870 Technical Support: (866) 956-1211
More informationMADE IN THE U.S.A. ADVANCE FIRE CONTROL MODEL LM21-AFC MANUAL RELEASE DEVICES TEST WEEKLY TO ASSURE PROPER OPERATION OF RELEASE DEVICE/CONTROL PANEL
RELEASE DEVICES MADE IN THE U.S.A. ADVANCE FIRE CONTROL MODEL LM21-AFC MANUAL The LiftMaster Fire Control (LM21-AFC) Release Device/Control Panel is UL/CUL listed normally energized fail-safe device incorporating
More informationTHE "SS90" SERIES RELEASE DEVICES MODEL B2 INSTALLATION MANUAL
S S S S S S S S 90 OLID TATE ECURITIES, INC SOLID STATE FAIL-SAFE UNIT * PATENT PENDING LISTED U 99Y9 RESET L RELEASING DEVICE SOLID STATE SECURITIES, INC. THE "SS90" SERIES RELEASE DEVICES MADE IN THE
More informationPN: 53049:A1 ECN Agent Release Control System MRP-2002 MRP-2002E. Document # /01/08 Revision: A1
PN: 53049:A1 ECN 08-319 Agent Release Control System MRP-2002 MRP-2002E Document #53049 5/01/08 Revision: A1 Fire Alarm System Limitations While a fire alarm system may lower insurance rates, it is not
More informationDesigo TM Fire Safety System A comprehensive fire-protection system
s Desigo TM Fire Safety System A comprehensive fire-protection system Standard 252-point and 504-point capacity systems Remote viewing for the 252- point and 504-point systems One (1) or (2) two-heightunit
More information