Conventional Fire Alarm System 2014 V1.2
|
|
- Emmeline Fisher
- 6 years ago
- Views:
Transcription
1 Conventional Fire Alarm System 2014 V1.2
2 Product Overview Control Panel 2
3 Conventional Fire Panel GST102A 2 zone Fire panel GST104A 4 zone Fire panel GST108A 8 zone Fire panel GST116A 16 zone Fire Panel 3
4 System Configuration Detection Zone: 2 to 16 zones With Active End of Line (AEOL), each zone can be configured with Max. 15 detectors With End of Line Resistor (EOLR), each zone can be configured with Max.25 detectors The total number of detectors and manual call points in a zone shall not exceed 32 Diode base should be applied when AEOL is used Recommended Cable Length: not longer than 1000m 4
5 System Configuration Sounder output: 4 channels) Alarm output: 1 channel Output Voltage: 18VDC ~ 28VDC Output Current: 300mA for each sounder output 300mA for fire alarm output End of Line Resistor: 4.7kΩ Recommended Cable Length: not longer than 1000m 5
6 System Configuration Auxiliary Power Output 18VDC~28VDC 20mA normally 500mA under fire condition Fault Output: Volt-free contact, 1A/24VDC REPEATER OUTPUT: Output terminal for GST-RP16 repeater panel QTY: 1 Distance:200m 6
7 System Configuration Remote input: Day mode input EVAC input SILENCE input RESET input Normally Open Contact input, close to active 7
8 System Configuration Backup Battery Max. Battery Charging Capacity: 2 batteries, 7AH/12VDC Battery Type: Sealed lead-acid battery Min. Operating Voltage: 21.5V Max. Charging Voltage: 27.6V Max. Internal Resistance of the Batteries: 1Ω Max. Operating Current of the Batteries: 2.5A 8
9 Product Overview Field Devices 9
10 Innovative Conventional Multi Detector Standard: EN54-5/EN54-7 Operating voltage: 24VDC Standby Current: 60μA Alarm Current: 10mA I 30mA Built-in remote indicator output Magnetic test Special LED blink under certain degree of DC-9101E Conventional Combination Heat Photoelectric Smoke Detector dirty; fire alarm when 100% dirty A2R Heat alarming IP23 DB-01D Diode Base DB-01 Standard Base C-9314P Remote Indicator 10
11 Innovative Conventional Optical Smoke Detector Standard: EN54-7 Operating voltage: 24VDC Standby Current: 60μA Alarm Current: 10mA I 30mA Special LED blink under certain degree of dirty; fire alarm when 100% dirty Built-in remote indicator output DC-9102E Conventional Photoelectric Smoke Detector Magnetic test IP23 DB-01D Diode Base DB-01 Standard Base C-9314P Remote Indicator 11
12 Innovative Conventional Dual Heat Detector Standard: EN 54-5 Operating voltage: 24V DC Standby Current: 60μA Alarm Current :10mA I 30mA A1R/A1S/BS Selectable Built-in remote indicator output Magnetic test DC-9103E Conventional Rate of Rise and Fixed Temperature Heat IP22 DB-01D Diode Base DB-01 Standard Base C-9314P Remote Indicator 12
13 Active End of Line Unit Reporting fault and keep loop continuity when detector is removed from base Operating Voltage : 24VDC Operating Current : 5mA Equivalent Resistor : 4.7kΩ IP33 DP-9907 Active End of Line Unit 13
14 Innovative Conventional Manual Call Point Standard: EN Non-breaking glass Reset by special key Operating voltage: 24V DC Standby Current: 0mA Alarm Current: 50mA IP43 DC-9204E Innovative Manual Call Point 14
15 Conventional Sounder and Strobe Standard: EN 54-3 Two tones selectable by different jumper setting, Active Power: 24VDC (20V~28V) Current 35mA Easy installation and connection Ultra bright LED Flasher IP33C C-9403 Conventional Sounder Strobe C-94DB deep base (Optional) 15
16 Conventional Sounder Standard: EN 54-3 Two tones selectable by different jumper setting, Active Power: 24VDC (20V~28V) Current 35mA Easy installation and connection IP33C C-9404 Conventional Sounder C-94DB deep base (Optional) 16
17 Repeater Panel Powered from conventional fire panel Common alarm indication Common fault indication Zone alarm indication GST-RP16 Conventional Repeater Panel Operating Voltage : 24VDC Standby Current : 12mA Active Current : 60mA 17
18 Relay Board Accessory of conventional fire panels Individual N/O relay for fire and fault signal of each zone Contact Capability :24VDC/1A RB102A RB104A RB108A for GST102A for GST104A for GST108A RB116A for GST116A 18
19 System Connection 19
20 System Connection System Connection Active EOL P-9907 EOL 4.7kΩ 20
21 System Connection Zone connection with EOLR Using EOLR (4.7kΩ) Manual Call Point should be connected before detectors. If a detector is removed, other devices installed after it can not work anymore 21
22 System Connection Zone connection with AEOL Add a diode on each base when using Active End Of Line. Using P-9907 AEOL Manual Call Point can be anywhere when using AEOL. If a detector is removed, other devices installed after it can still work normally. 22
23 System Connection Special detection connection + Zone - 4k7Ω 470Ω For special requested detection, like Flow Switch or Zonal Valve, a N/O contact is required connecting to a zone. Connection as above to make a FIRE signal when the equipment is activated. 23
24 System Connection Sounder connection + Sounder Output 4.7kΩ _ Polarized conventional sounders can be connected to the sounder circuit, with 4k7 EOLR at the end. 24
25 Panel Operation 25
26 Panel Operation Status Indicators Zone Indicators System Control 26
27 Panel Operation LED Indications 27
28 Panel Operation FIRE: Any zone in fire Alarm Output: Alarm output activated Common Fault: Any type of fault System Fault: CPU fault Disable: Any type of disable 28
29 Panel Operation Power Supply: Delay Mode: Ground Fault: Power Fault: In Test: AC or battery working Day mode (delay enabled) Any cable grounded Mains fault, Battery fault, Charger fault or Hi battery resistance A zone is in test condition. 29
30 Panel Operation Output Indicators Flashes when output in fault condition Lit steadily when output is disabled 30
31 Panel Operation Operation Keys (with LED) 31
32 Panel Operation Control Enable Key Switch The key switch controls access level 2 Only when the switch is in ON position, the operation button can take effect, except Mute and Acknowledgement 32
33 Panel Operation Disable/Enable: Output Program: Test: EVAC: Silence/Resound: To disable or enable an output or a zone To program the outputs To set a zone into test mode To start all sounder outputs To stop all activated sounder outputs. Press again to resound. 33
34 Panel Operation : Shift between Day & Night modes Cancel: Enter: Reset: Mute/ACK: Exist operation Confirm operation Reset panel to normal mode. Exist operation. Self test. Changing the silence status of the internal buzzer. 34
35 Panel Operation Zone Indicators and Operation Instruction FIRE FAULT & DISABLE Operation Instruction Zone Label 35
36 Conventional Panel Operation and Setup 36
37 Panel Operation Acknowledgement and Silence of Fire Alarm A fire alarm can be acknowledged and silenced at access level 1. Pressing Mute/ACK under fire alarm condition, the buzzer of the FACP will be mute and the alarm is acknowledged. FIRE LED and zone red LED will light. If there is a new fire alarm from another zone, the zonal red LED will flash. Pressing Mute/ACK, it will illuminate steadily. Acknowledgement and Silence of Fault A fault condition can be acknowledged and silenced at access level 1. Pressing Mute/ACK under a fault condition, the buzzer of the FACP will be mute and the fault is acknowledged. Common Fault LED will illuminate steadily. 37
38 Panel Operation Silencing the Sounders The sounders can be silenced at access level 2. Pressing Silence/Resound can silence the sounders. In fire alarm state, pressing Silence/Resound will silence the sounders and pressing it again will make them resound. If the SILENCE INPUT contact is shorted for over 2s, the FACP will silence the sounders regardless of the current access level. Evacuation The evacuation can be operated at access level 2. Pressing EVAC key, all sounders will enter EVAC mode to sound continuously. If the EVAC INPUT contact is shorted for 2s, the FACP will activate EVAC function to start all sounders regardless of the current access level. 38
39 Panel Operation Self-test and Reset Self-test and Reset can be carried out at access level 2. Pressing the Reset will clear all audio and visual indication, and the panel will followed by self-test. The self-test can check all indicators and the buzzer. All indicators illuminate and the buzzer sounds. After self-test, the panel returns to normal condition. If the RESET INPUT contact is shorted for over 2s, the FACP will start reset and selftest regardless of the current access level. 39
40 Program and Setup Setting Access Level Access Level Operation Key Switch DIP 1 of SW2 1 Stop panel alarm buzzer by pressing Mute/ACK key. OFF OFF 2 Mute/ACK ON OFF Disable Test Reset Silence/Resound Evacuate SW2 SW3 3 Operations of Access Level 1 ON/OFF ON Program the outputs 40
41 Program and Setup Sounder/Alarm Output Setup Sounder outputs and alarm output can be set to one of the three types through on the control board, live output (output 24VDC when activated), normally open contact or normally closed contact. The default setting is voltage output. Output N/C contact N/O contact Jumpers Jumpers Sounder 1 X1/ 1&2, 3&4 X1/ 1&2, 4&5 Sounder 2 X2/ 1&2, 3&4 X2/ 1&2, 4&5 Sounder 3 X3/ 1&2, 3&4 X3/ 1&2, 4&5 Sounder 4 X4/ 1&2, 3&4 X4/ 1&2, 4&5 Alarm output X5/ 1&2, 3&4 X5/ 1&2, 4&5 41
42 Program and Setup The FACP will be able to check earth fault when X6 (EARTH FAULT) is shorted with a jumper. Otherwise, the earth fault will be ignored. Setting auxiliary power output: If the devices powered by Aux. 24V require steady output, you can connect 24V and AUX SUPPLY of X8 with a jumper. If they are to be reset together with the FACP, you can connect Loop 24V and AUX Supply with a jumper, so that AUX Supply stops output for about 3 seconds when the panel resets. 42
43 Program and Setup Panel programming The panel can be programmed as an addressable system. The main feature is to program the actions of the sounder outputs during fire alarm. Max. 7.5 minutes delay can be set to the outputs. To achieve delay operation, below settings must be taken. 1. The alarming zone does not have manual call point 2. The related sounder output is set in delay output mode 3. A delay time has been set 4. The panel is in DAY mode If this feature is not required, please ignore this section, keep the panel in default setting. 43
44 Program and Setup Default Setting The system provides a quick method to set the system to default: Enter Access Level 3 Press and hold Output Program for more than 2 seconds, and the system will enter default state with 1s sound indication. Exit Access Level 3. System default settings All zones are With Manual Call Point. Alarm from any zone will activate all sounders continuously and immediately Alarm Output is activated without any delay. There is no disabled zone or output. 44
45 Program and Setup DIP Application Note 1 Access Level 3 All setup must be done under Access Level 3 2 With Manual Call Point The purpose of this feature is to ensure that activating a manual call point in field will immediately generate a fire alarm in the system. If a zone is set With Manual Call Point, any fire alarm coming from that zone (either from a detector or a manual call point), the FACP will immediately alarm and activate all sounders associated to that zone and the system Alarm Output regardless of any delay setting. At the same time, delay to outputs is overridden. This function can be applied to all detection zones. S W I T C H 2 3 Associated Sounders of a Zone 4 Delay Time of Alarm Output Output state, output mode and delay time of sounders can be set separately for each detection zone. Set 4 of SW2 to ON position.then delay time of Alarm Output can be set. 5 Resound mode When 5 of SW2 is set to ON position, Resound mode is turned on. When there is fire alarm from a zone, the sounders associated to this zone will be started. Pressing Silence on the FACP, these sounders can be silenced; if there is an alarm signal from another zone at this moment, the silenced sounders that are not associated to this new alarm zone will resound. If Resound mode is turned off, the silenced sounders not associated to this new alarm zone will remain silenced. 6 Silence-Reset mode When 6 of SW2 is set to ON position, Silence-Reset mode is turned on. When there is fire alarm from a zone and its associated sounders are started, the FACP will not be reset until the sounders are silenced. If Silence-Reset mode is turned off, the FACP can be reset immediately. 7 Silence-Delay mode When 7 of SW2 is set to ON position, Silence-Delay mode is turned on. When there is fire alarm from a zone and its associated sounders are started, the FACP has to stay in fire condition for 3 minutes before the sounders could be silenced. If Silence Delay mode is turned off, the sounders can be silenced immediately. 8 Test Zone Silence mode When 8 of SW2 is set to ON position, Test Zone Silence mode is turned on. When a zone is in Test mode and there is an alarm signal coming from the zone, the sounders associated to the zone will be automatically activated for 15s. If Test Zone Silence mode is turned off, the sounder will not be activated. 45
46 Program and Setup With Manual Call Point 1. Enter Access Level 3 as described in Section 3.1.3; 2. Set 2 of SW2 (CFG MCP ZONE) on control board to ON position. 3. Pressing Output Program, Output Program LED illuminates steadily and the amber LED of Zone 1 flashes to show Zone 1 is selected for With Manual Call Point setup. Common Fault LED will indicate a system fault condition. Other indicators, except for the above mentioned LEDs, will be turned off. 4. Pressing will switch the zone number from 1 to The amber LED for Zone 1 to 8 will flash when the zone is selected. Pressing Output Program key can choose whether or not to program the zone as With Manual Call Point or not. The illuminating Delay Mode LED indicates the zone is not programmed as With Manual Call Point. 6. Press Enter to save the current settings and exit after all settings have been finished. The FACP will give 1s sound indication. Pressing Cancel will not save the setting. 7. Press Cancel to exit the programming mode and Output Program LED turns off. 8. Set 2 of SW2 to OFF position. 9. ExitAccess Level 3. 46
47 Program and Setup Associated Sounders of a Zone 1. Enter Access Level 3 as described before. 2. Set the 3 of SW2 (CFG Zonal output) on control board to ON position. 3. Pressing Output Program key, Output Program LED illuminates steadily and the amber LED of Zone 1 flashes to show Zone 1 is selected for setting up associated sounders. Common Fault LED will indicate a system fault condition. Other indicators, except for the above mentioned LEDs, will be turned off. 4. Pressing will shift the zone from 1 to When a zone is selected, press Output Program key to set up its associated zones. Flt/Dis LED of Sounder1 flashes, showing Sounder1 has been selected for setup. 6. Pressing will shift from Sounder1 to Sounder4. 7. Pressing Disable/Enable or Test Key can respectively switch on or off their indicator. Disable/Enable Key & LED and Test Key & LED are used for setting up and indicating the output logic of the selected sounder. 8. Switching 5 of SW3 (Sounder Mode) on or off can change the sound pattern of the selected sounder 9. 1 to 4 of SW3 are used for setting the delay time of the selected sounder. 10.Press Enter to save and exit the current settings. The FACP will sound for 1s to indicate the successful setup. Repeat Step 6 to 9 to set another sounder for this zone. 11.Press Cancel to exit setup for this zone without saving and return to zone selection step. Repeat Step 4 to 10 to select another zone for setup. 12.At zone selection step, pressing Cancel again will exit programming mode. And Output program LED will be turned off. 13.Set 3 of SW2 (CFG Zonal Output) to OFF position. 14.Exit Access Level 3. 47
48 Program and Setup Mode Description Disable/Enable LED Test LED 1 No output Off Off 2 Relay on alarm relay output Off On 3 Delay output On Off 4 Immediate output On On 48
49 Program and Setup Setting Delay Time of Alarm Output Delay time of Alarm Output can be set through the following steps. 1. Enter Access Level Set 4 of SW2 to ON position. 3. Pressing Output Program key, Output Program LED illuminates steadily and Alarm Output Flt/Dis LED flashes to 4 of SW3 are used for setting the delay time of Alarm Output 5. Pressing Enter to save the setting. The FACP will sound for 1s to indicate the successful setup. Pressing Cancel will not save the setting. 6. Pressing Cancel will exit programming mode and Output Program LED turns off. 7. Set 4 of SW2 (CFG alarm output-delay) to OFF position. 8. Exit Access Level 3. 49
50 Program and Setup Switch 3 Setup SWITCH Used together to set the delay time of the sounder/alarm output Sounder Patterns Alert mode, pulse output Evacuation mode, continuous output the sound pattern of the selected sounder Switching 5 of SW3 (Sounder Mode) on or off can change the sound pattern of the selected sounder 5 of SW3 (Sounder Mode) Off On Delay (min) 1 to 4 of SW3(Delay) Off Off Off Off 0.5 on Off Off Off 1 Off on Off Off 1.5 on on Off Off 2 Off Off on Off 2.5 on Off on Off 3 Off on on Off 3.5 on on on Off 4 Off Off Off on 4.5 on Off Off on 5 Off on Off on 5.5 on on Off on 6 Off Off on on 6.5 on Off on on 7 Off on on on 7.5 on on on on 50
51 Program and Setup Setting Day/Night Mode Day and night mode is related with output delay. If there is person on duty, you can set the panel to Day mode, thus any fire alarm output will be delayed for confirmation to avoid false alarm. If there is nobody on duty, you can set the panel to Night mode, so that the FACP will alarm immediately on receiving a fire signal. There are two ways to shift between Day/Night modes. DAY MODE input signal is closed to force the FACP to Night mode. Pressing for 2 seconds at access level 2 will change the Day/Night Mode. The panel gives 1s sound for indication. If Day mode is selected, the Delay Mode LED illuminates. If Night Mode is selected, the Delay Mode LED turns off. Note: If the panel has worked in Day mode for 18 hours, it will automatically change to Night mode. The margin of time error can be ±5%. 51
CONTENTS. GST102A/104A/108A/116A Conventional Fire Alarm Control Panel Installation and Operation Manual
CONTENTS Installation Precautions... 1 EN 54 Information... 2 Chapter 1 Product Overview... 3 1.1 Features... 3 1.2 Technical Specifications... 3 1.2.1 Operating Voltage... 3 1.2.2 Batteries... 3 1.2.3
More informationInstallation, Operating and Maintenance Manual
STATUS ZONES CONTROLS FIRE FAULT DISABLED FIRE 1 2 3 4 5 6 7 8 TEST FAULT DISABLED 1 5 BUZZER SILENCE RESET 1 2 TEST 2 6 LAMP TEST 3 SUPPLY 3 7 SYSTEM FAULT 4 8 SOUNDERS ACTIVATE/ SILENCE 4 FAULTS INSTRUCTIONS
More informationPNC 1000 SERIES 2, 4, 8 Zone Fire Alarm Control Panel
PNC 1000 SERIES 2, 4, 8 Zone Fire Alarm Control Panel INSTALLATION, OPERATION AND MAINTENANCE MANUAL Version: CN-PM-1000.VER1.1-12/2012 EN54 INFORMATION In accordance with EN 54-2 clause 13.7, the maximum
More informationInstallation and user manual for the CF5000, MF5000 and FXP5000 range of fire panels
CF5000, MF5000 and FXP5000 Installation and user manual for the CF5000, MF5000 and FXP5000 range of fire panels 16 zone panels Contents PANEL INSTALLATION...3 Installation...3 PANEL WIRING... 3 Mains power
More informationInstallation and user manual for the FX range of fire panels. 1, 2, 4 and 8 zone panels
Installation and user manual for the FX range of fire panels 1, 2, 4 and 8 zone panels Contents Panel installation 3 Panel connections 3 Wiring connection drawings 4 Panel facilities 6 Installation check
More informationExcel-EN Conventional Fire Control Panel
Available as 2, 4, 6, 8,10 or 12 zones Approved to EN54-2 & 4 Modular expansion zone cards Programmable relays and outputs Optional additional sounder circuits Optional additional programmable outputs
More informationCONTENTS Installation Precautions... 1 Chapter 1 Product Introduction... 2 Chapter 2 Technical Specifications... 3
CONTENTS Installation Precautions... 1 Chapter 1 Product Introduction... 2 Chapter 2 Technical Specifications... 3 2.1 Electrical Specifications... 3 2.2 Communication Loop Parameters... 3 2.3 Dimensions...
More informationTECHNICAL DATA SHEET CONVENTIONAL FIRE ALARM SYSTEMS Conventional Fire Alarm Control Panel
CVENTIAL ALARM S Features: Description: The LF-CP Series Fire Alarm Control Panel is manufactured based on advanced technology while maintaining high quality during assembly. It is of solid state circuitry
More informationControl Panel Engineering and Commissioning Instructions
Twinflex - V3 Fire Detection & Alarm System Control Panel Engineering and Commissioning Instructions (TO BE RETAINED BY THE COMMISSIONING ENGINEER) 26-0338 Issue 9 Fike s policy is one of continual improvement
More informationPanel Functions & Indicators - Key to Icons General & Zone Fire LEDs ACCEPT SOUNDERS START/ STOP RESET BUZZER MUTE KEYSWITCH DELAY ON/OFF ITEM SELECT
Islenska Français Deutsch Nederlands Svenska EN54-8 Zone Conventional Fire Control Panel User Manual 997-493-00, Issue 0 November 003 Panel Functions & Indicators - Key to Icons General & Zone Fire LEDs
More informationED820-24V MODEL INSTRUCTION MANUAL. fire DETECTOR
ED820 24V MODEL fire DETECTOR INSTRUCTION MANUAL Address: Enigma House, Enigma Business Park, Malvern, Worcestershire, WR14 1GD Tel: 44 (0)1684 891500 Fax: 44 (0)1684 891600 Email: sales@electronicdevices.co.uk
More informationSystem 800 Addressable Fire Detection & Alarm System
SECTION 5: page 1 Section 5: System 800 Addressable Fire Detection & Alarm System SECTION 5: page 3 10 reasons to specify 800 1 Plug and Play A user friendly panel not requiring special software tools
More informationIntelligent Security & Fire Ltd
OPERATIONAL NOTES FOR CONCEPT FIRE PANEL. NOTE ON NEW FIRE PANELS, POSITION 1 ON THE SIX WAY INTERNAL OPTION SWITCH IS TURNED ON, DISABLING THE ZONAL SOUNDERS. TO ENABLE ZONAL SOUNDERS TURN OFF. Operation
More informationMR-2602 Two Zone Fire Alarm Control Panel
MR-2602 Two Zone Fire Alarm Control Panel Installation Manual Secutron LT-2015 Rev.3 July 2010 Table of Contents 1 Introduction 1.1 The MR-2602 Fire Alarm Control Unit... 11 1.1.1 General features...
More informationThe ID51 & ID52 can be upgraded to 2 loops without the need to change back box. FEATURES. Intelligent Features
990-052, Issue 6 20 March 2006 ID50 Series Single Loop Intelligent Fire Alarm Panels Section: Intelligent Fire Alarm Panels GENERAL The NOTIFIER ID50 series single loop intelligent fire alarm panels, has
More informationOPERATION AND INSTALLATION MANUAL
EX+Plus 2 ZONE, 1AREA EXTINGUISHANT CONTROL PANEL OPERATION AND INSTALLATION MANUAL INTRODUCTION The Premier EX Plus is a 2 zone, single area panel for controlling the release of extinguishing gases in
More informationNFS Supra / VSN-2Plus / ESS-2Plus Conventional Fire Alarm Control Panel. Installation and Operating Manual
/ VSN-2Plus / ESS-2Plus Conventional Fire Alarm Control Panel Installation and Operating Manual HLSI-MN-025-I v.05 April 2015 Note: This manual is valid for the following control panel models: NFS-Supra
More informationINTELLIGENT FIRE TECHNOLOGY. Twinflex and Multipoint V3. User Guide (TO BE RETAINED BY USER) Issue 3
INTELLIGENT FIRE TECHNOLOGY Twinflex and Multipoint V3 User Guide (TO BE RETAINED BY USER) 26-0340 Issue 3 Rafiki Protection Limited Rafiki policy is one of continual improvement and the right to change
More informationSaffire User & Installation Manual. IMPORTANT This manual should be left with the panel after installation.
Saffire+ 8-12 User & Installation Manual IMPORTANT This manual should be left with the panel after installation. We reserve the right to change product specifications without prior notice. Copyright VRC
More informationuser manual Document No , Revision 03 November 2015
user manual Document No. 996-202-600-3, Revision 03 November 2015 Contents 1 Introduction...1 1.1 Notice...1 1.2 Models...1 2 User Control Levels...2 2.1 Level Definition...2 2.2 User Passwords...2 3 Controls
More informationBT1 SINGLE ZONE FIRE ALARM SYSTEM OPERATORS MANUAL
BT1 SINGLE ZONE FIRE ALARM SYSTEM OPERATORS MANUAL 26 Aug 2015 V1.8 Page 1 SECTION CONTENTS PAGE NO. 1.0 SYSTEMS DESCRIPTION 1.1 General descriptions 2 1.2 Master Alarm PCB 2 1.3 Zone Display Board 2 1.4
More informationApplication, Installation, Operation & Maintenance Manual
APPROVED BY:JBJ PRESCIENT III FIRE ALARM & GAS EXTINGUISHING CONTROL PANEL Application, Installation, Operation & Maintenance Manual PAGE 1 of 43 CONTENTS 1. INTRODUCTION... 3 2. GENERAL DESCRIPTION...
More informationAL802ULADA. NAC Power Extender. Installation Guide. (See Application Guide for additional information) Rev
AL802ULADA NAC Power Extender Installation Guide (See Application Guide for additional information) Rev. 031703 Overview: The Altronix AL802ULADA is an extremely cost effective 8 amp voltage regulated
More informationSigma. K1000 Series 1, 2, 4 & 6 Zone Fire Control Panels. Operation and Maintenance Manual. Man-1048 Issue 05 October 2009
Sigma K1000 Series 1, 2, 4 & 6 Zone Fire Control Panels Operation and Maintenance Manual Man-1048 Issue 05 October 2009 CONTENTS Contents... Page Safety & Installation...2 Installation - continued...3
More informationInstallation Guide for AL800UL-ADA. NAC Power Extender. Rev
Installation Guide for AL800UL-ADA NAC Power Extender Rev. 090500 Overview: The Altronix AL800UL-ADA is an extremely cost effective 8 amps voltage regulated remote power supply /battery charger. The AL800UL-ADA
More informationIntelligent Security & Fire Ltd
full installation, commissioning and operating manuals can be downloaded from www.haes-systems.co.uk combined addressable / conventional fire alarm control panel User Guide Approved Document No. MFBU-04
More informationLC1 & 2. Fire Alarm Panel 6\VWHPLQVWDOODWLRQRSHUDWLQJ PDLQWHQDQFH LQVWUXFWLRQV
LC1 & 2 Fire Alarm Panel 6\VWHPLQVWDOODWLRQRSHUDWLQJ PDLQWHQDQFH LQVWUXFWLRQV ZIRCONLC1 One Zone Conventional Fire Panel ZIRCONLC2 Two Zone Conventional Fire Panel Compliant with EN54-2:1998 & EN54-4:1998
More informationZX1e ZX2e ZX5e. Document No Issue 01 user manual
ZX1e ZX2e ZX5e Document No. 996-130 Issue 01 user manual MORLEY-IAS ZX2E/ZX5E Fire Alarm Control Panels Table of Contents 1 INTRODUCTION... 4 1.1 NOTICE... 4 1.2 WARNINGS AND CAUTIONS... 4 1.3 NATIONAL
More informationAL800ULADA. NAC Power Extender. Installation Guide
AL800ULADA NAC Power Extender Installation Guide Rev. 122000 AL800ULADA - NAC Power Extender Overview: The Altronix AL800ULADA is an extremely cost effective 8 amp voltage regulated remote power supply/battery
More information3500 CONVENTIONAL FIRE ALARM CONTROL PANEL
3500 CONVENTIONAL FIRE ALARM CONTROL PANEL INSTALLATION AND COMMISSIONING MANUAL Protec Fire Detection PLC, Protec House, Churchill Way, Nelson, Lancashire, BB9 6RT. Telephone: +44 (0) 1282 717171 Fax:
More informationCONVENTIONAL CONTROL PANEL FL2/4/8/12 LT-XP
FLx-LT-XP CONVENTIONAL CONTROL PANEL FL2/4/8/12 LT-XP Installation, Configuration and Operating Manual MAY 2008 MIE-MI-580I_FL rev.003 Information in this document is subject to change without notice.
More informationUser Operation Manual
APPROVED BY: JBJ PRESCIENT III FIRE ALARM & GAS EXTINGUISHING CONTROL PANEL User Operation Manual PAGE 1 of 6 1 CONTENTS 1. FIRE - GENERAL... 3 2. FIRE - ZONES 1 OR 2 - AUTOMATIC MODE... 3 3. FIRE - ZONES
More informationAL600ULADA. NAC Power Extender. Installation Guide
AL600ULADA NAC Power Extender Installation Guide Rev. 122000 AL600ULADA - NAC Power Extender Overview: The Altronix AL600ULADA is an extremely cost effective 6.5 amp voltage regulated remote power supply/battery
More informationFire-Cryer. Plus Application Guide APPLICATION GUIDE FIRE EXIT VIMPEX. Shaping Alarm Technology
Fire-Cryer Plus Application Guide APPLICATION GUIDE FIRE EXIT VIMPEX Shaping Alarm Technology Fire-Cryer Plus The Fire-Cryer range of voice sounders was first introduced to the market by Vimpex in 1999.
More informationGeneral Routing Interface
General Routing Interface Features The General Routing Interface Card is an optional module to provide Fire and Fault Routing Outputs compliant with BSEN54-2: 1998 Clauses 7.9 and 8.9 and BS5839-1: 2002.
More informationInstallation Manual CFP-105. Fire Alarm Control Panel. Version 1.0
CFP-105 Fire Alarm Control Panel Installation Manual Version 1.0 WARNING: This manual contains information on limitations regarding product use and function and information on the limitations as to liability
More informationFTEN1, FTEN2, & FTEN4 1, 2 & 4 ZONE FIRE DETECTION AND ALARM CONTROL PANELS
QUICK USER GUIDE FOR, 2 & 4 ZONE PANELS INDICATORS COLOUR INDICATION MON FAULT Yellow On when a fault condition has occurred, or if no other fault Led is on, this indicates 24v auxiliary fuse failure.
More informationNZ 400 AUTOMATIC FIRE ALARM SYSTEM OPERATORS MANUAL
NZ 400 AUTOMATIC FIRE ALARM SYSTEM OPERATORS MANUAL Document No...G108WO1.DOC Serial No... Issue Date...17 th SEPTEMBER 1999 Software Version...1.4 APPROVED TO: NZS 4512:1997 AS/NZS 3548:1992 Fire Alarm
More informationTX7004. Intelligent Addressable Fire Alarm Control Panel Installation and Operation Manual. TANDA UK Technology Copyright 2015, All right reserved.
TX7004 Intelligent Addressable Fire Alarm Control Panel Installation and Operation Manual Technology Copyright 2015, All right reserved. Product Safety To prevent severe injury and loss of life or property,
More informationSyncro AS. Analogue Addressable Fire Control Panel. User Manual
Syncro AS Analogue Addressable Fire Control Panel User Manual Man-1100 Issue 02 Nov. 2008 Index Section Page 1. Introduction...3 2. Safety...3 3. Panel Controls...4 3.1 Access Level 1...4 3.2 Access Level
More informationFire Alarm Control Panel Installation, Commissioning & Operation MAN
DH4 ZoneSense Fire Alarm Control Panel Installation, Commissioning & Operation MAN 1531-5 Access Level 1 (Normal Operation) Responding To An Alarm Zone FIRE Alarm Indicator - flashing Common FIRE Alarm
More informationConventional Fire Detection
SECTI 4: page 1 Section 4: Conventional Fire Detection Contents System Architecture Control Panel Automatic & Manual Detection Manual Call Points Smoke Detectors Heat Detectors Beam Smoke Detectors Duct
More informationXenex Conventional Fire Detection & Alarm System
SECTI 4: page 1 Section 4: Xenex Conventional Fire Detection & Alarm System SECTI 4: page 3 Xenex system architecture Beam Transmitter Beam Receiver End of Line Call Point Smoke Detector Smoke Detector
More informationConventional Leaflets
Conventional Leaflets Panels Last updated October 1999 Make leaflet selection by clicking on appropriate bookmark Return to Menu Installation and Basic Commissioning guide for the range of 1,2,4 and 8
More informationFire Control Panel FS4000
Fire Control Panel FS4000 INSTRUCTION MANUAL Revision 4/02.11 Contents 1. Introduction... 4 2. Terminology... 4 3. Function... 5 4. Technical features... 5 4.1 Fire alarm lines... 5 4.2. Current thresholds
More informationFire Alarm System. The Intelligent Solution. Leading global technology Safe guarding lives and properties
Fire Alarm System The Intelligent Solution Leading global technology Safe guarding lives and properties Parent company UTC Headquartered in Hartford, Connecticut, USA, GST s parent company United Technologies
More informationGAS SUPRESSION CONTROL PANEL:
GAS SUPRESSION CONTROL PANEL: MODEL NAME: COMPANY: DELTA 437/2, Main Road, Mandwali Fazalpur, Delhi-110092 Page 1 ABOUT THE PRODUCT ASES is very proud of to introduce DELTA the completely digital microprocessor
More informationFIRE DETECTOR TYPE ED816 ZONE 5 ZONE 4 ZONE 6 ZONE 7 FIRE FIRE FIRE FIRE FAULT FAULT FAULT FAULT DISABLED DISABLED DISABLED DISABLED OFF OFF OFF OFF
DETECTOR TYPE ED816 ZE 1 ZE 2 ZE 3 ZE 4 ZE 5 ZE 6 ZE 7 S ZE 8 CIRCUIT 1 ZE 9 ZE 10 ZE 11 ZE 12 ZE 13 ZE 14 ZE 15 ZE 16 CIRCUIT 1 POWER POWER SUPPLY GENERAL MENT DC GENERAL SYSTEM ALARM DELAYED ALARM RESOUND
More informationOperating instructions SENTRI4 Control panel based Fire detection and alarm system
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 30 32 Zones Healthy 15:45 Fault Power Fault System Fault SenTRI 4 Fire System Designed to EN54 Pt 2 & 4 Operating instructions
More informationTX7004. Intelligent Addressable Fire Alarm Control Panel Installation and Operation Manual. TANDA UK Technology Copyright 2015, All right reserved.
TX7004 Intelligent Addressable Fire Alarm Control Panel Installation and Operation Manual Technology Copyright 2015, All right reserved. Product Safety To prevent severe injury and loss of life or property,
More informationVSN-RP1r Extinguishing Control Panel. User Manual (Software version 3.x) by Honeywell. doc. MIE-MN-570I rev.008
www.morley-ias.es by Honeywell VSN-RP1r Extinguishing Control Panel User Manual (Software version 3.x) doc. MIE-MN-570I rev.008 Information in this document is subject to change without notice. 22 June
More informationThe EN54 Part 2 and 4 Fire System
Scope of work: To design, supply, install and commission a Fire Alarm Control System in accordance with the details specified herein and in accordance with supplied drawings The EN54 Part 2 and 4 Fire
More informationOperating manual and Log book for the range of 1,2,4 and 8 zone fire Control and Repeat panels
Operating manual and Log book for the range of 1,2,4 and 8 zone fire Control and Repeat panels The panels are designed in accordance with the requirements of EN54 Part 2:1997 (and include optional clauses
More informationFire Extinguishing Control Panel INSTRUCTION MANUAL. Revision 8/ Instruction Manual Page 1 Revision 8/01.17 of 63
Fire Extinguishing Control Panel FS5200Е INSTRUCTION MANUAL Revision 8/01.17 Instruction Manual Page 1 1. 2. 3. 4. 4.1. 4.2. 4.2.1. 4.2.2. 4.2.3. 4.2.4. 4.2.5. 4.2.6. 4.2.7. 4.2.8. 4.2.9. 4.2.10. 4.2.11.
More informationUSER MANUAL & MAINTENANCE GUIDE OG OO
M+48. USER MANUAL & MAINTENANCE GUIDE OG OO What to do if the Fire Alarm Panel shows an Alarm (Red LED) Write down which LEDs are lit (either in the log book, or on a piece of paper for transferring to
More informationConventional Releasing Control Panel
s Data Sheet Fire Safety Products Conventional Releasing Control Panel Pre-Action Deluge Agent-Releasing Fire System Model TXR-320 Remote configurable Up to two (2) hazard areas Operable with the following:
More information2018 Johnson Controls. Tyco Fire & Security GmbH, Victor von Bruns-Strasse 21, 8212 Neuhausen am Rheinfall, Switzerland DUO-CEL
OM_FC_DUO-CEL_APP 2018 Johnson Controls. Tyco Fire & Security GmbH, Victor von Bruns-Strasse 21, 8212 Neuhausen am Rheinfall, Switzerland DUO-CEL FIRE DETECTION/ALARM PANEL Application Guide PAGE 1 of
More informationMenvier Fire System MF9300
Menvier Fire System MF9300 Eight and sixteen zone control panels Installation and User Instructions and Systems Log IMPORTANT THIS MENVIER FIRE PANEL IS DESIGNED TO BE USED WITH POLARISED AND SUPPRESSED
More informationAL802ULADA. NAC Power Extender. Installation Guide. (See Application Guide for additional information)
AL802ULADA NAC Power Extender Installation Guide (See Application Guide for additional information) Rev. 042010 Agency Listings: UL Listed Control Units for Fire Protective Signaling Systems (UL 864).
More informationELECTRONIC SOUNDER STROBE Model : AVD-C407
ELECTRONIC SOUNDER STROBE Model : AVD-C407 MULTRON range of combination Electronic Sounders with Strobe Lights are designed to complement our Fire Alarm products both technically and aesthetically as an
More informationControl Panel User Guide
Fire Detection & Alarm System Control Panel V4.14 Control Panel User Guide (TO BE RETAINED BY USER) 26-0397 Issue 6 Fike s policy is one of continual improvement and the right to change a specification
More informationThe complete conventional fire warning system
The complete conventional fire warning system www.espuk.com MAG2P 2 Zone Fire Panel 2 programmable zones Active end of line monitoring and head removal 30 fire detectors per zone Unlimited number of call
More informationInstallation, Commissioning & Operating Manual
EN54 APPROVED 2-4 ZONE ALARMSENSE CONTROL PANEL Installation, Commissioning & Operating Manual 810a/05 Approved Document UI-ALS-01 Issue 2.0 0832 Haes Systems Ltd, Columbia House, Packet Boat Lane, Cowley
More informationOperating instructions Vigilon panel and Network node Fire detection and alarm system
Healthy 15:45 Fault Power Fault Vigilon Fire System GENT 2015 Designed to EN54 Pt 2 & 4 System Fault Operating instructions Vigilon panel and Network node Fire detection and alarm system Test Fire Fault/Dis
More informationTECHNICAL DATA OBSOLETE
Deluge Devices 270a 1. PRODUCT NAME VIKING PAR-3 Available since 1991 2. MANUFACTURED FOR: THE VIKING CORPORATION 210 N. Industrial Park Road Hastings, Michigan 49058 U.S.A. Telephone: (269) 945-9501 (877)
More informationFA-300 Series. LED Fire Alarm Control Panel. User Guide. FA-300 SERIES Fire Alarm Control Panel. FA-300 SERIES Fire Alarm Control Panel
LAMP TEST REMOTE CPU FAULT GROUND FAULT SIGNAL SILENECE FIRE DRILL BUZZER SILENCE INFO AC ON ALARM SUPERVISORY BATTERY SYSTEM RESET AUXILIARY DISCONNECT LAMP TEST MENU LAMP TEST REMOTE CPU FAULT GROUND
More informationSurveyor Excel. Fire Alarm Control Equipment Network version. Programming Manual MASTER MANUAL. VERSION 14.0 and Above
Surveyor Excel Fire Alarm Control Equipment Network version Programming Manual VERSION 14.0 and Above MASTER MANUAL Drawing S1606. PCB Layout guide for XLK range of control panels FCPXLK-2/4/6/8 & FCPXLK2/4/6/8TW
More informationEX8. Instruction Manual: COMBINED FIRE & EXTINGUISHING CONTROL PANEL COMPLIES WITH BS EN PART 1 AND EN54 PARTS 2 & 4
EX8 COMBINED FIRE & EXTINGUISHING CONTROL PANEL COMPLIES WITH BS EN 12094 PART 1 AND EN54 PARTS 2 & 4 Instruction Manual: Approved Document No: GLT.MAN-124 PAGE 2 INDEX INDEX... 3 Introduction... 4 Indications
More informationSFC-200 SERIES LED FIRE ALARM PANEL
SFC-200 SERIES LED FIRE ALARM PANEL USER GUIDE LT-953SUM SFC-200 Series LED Version User Guide Contents Contents... i Introduction... 1 About this Manual... 1 Technical Support... 1 Main Display... 2
More informationVSN PLUS VSN 4 PLUS ; VSN 8 PLUS ; VSN 12 PLUS
Installation, Configuration and Operating Manual VSN PLUS VSN 4 PLUS ; VSN 8 PLUS ; VSN 12 PLUS HLSI-MI-130I 19 March 2010 Information in this document is subject to change without notice Contents 1 Introduction
More informationInstallation Instructions 4 Zone Fire Panel
Installation Instructions 4 Zone Fire Panel General Features Four fully controlled zones with test / disable capability per zone. Two full controlled alarm lines with disable capability per line. 4V/800mA
More informationSYSTEM MANUAL FT1-SB. Single Zone Fire Alarm System
SYSTEM MANUAL FT1-SB Single Zone Fire Alarm System DOCUMENT HISTORY Issue Date Description Written By Checked By Draft 0 2/9/2008 Original Document. A. Shenouda C. Orr Issue 1 4/11/2011 Update drawing
More informationControl/Communicator Installation Manual
DAS NETWORX NX-12 Control/Communicator Installation Manual General Description...2 Ordering Information...2 Option Definitions...3 Programming the LED Code Pads...5 Programming the NX-12...9 Types of Programming
More informationSpecification/ Data Sheet
Specification/ Data Sheet TRITON RP Agent Release Control Panel FEATURES Agent Release Control Panel designed specifically for suppression release operation with: Four initiating device circuits (IDCs)
More informationFIRE BRIGADE RESPONSE GUIDE. LoopSense. Fire Alarm Control Panel (AS4428 & AS & 4) Operation & Onsite Programming MAN
LOOPSENSE FIRE BRIGADE RESPONSE GUIDE LoopSense Fire Alarm Control Panel (AS4428 & AS7240. 2 & 4) Operation & Onsite Programming MAN 1567-2 LOOPSENSE FIRE BRIGADE RESPONSE GUIDE Responding to a Fire Access
More informationFEC403EN Installation Manual
FEC403EN Installation Manual P/N 10-4101-501-2FC1-01 ISS 22JAN15 Copyright Trademarks and patents Manufacturer 2015 UTC Fire & Security. All rights reserved. The FEC403EN name and logo are trademarks of
More informationEXTINGUISHING AGENT RELEASE MODULE
EXTINGUISHING AGENT RELEASE MODULE Operation, Installation & Programming Manual Revision 3.00 Distributors For: 18-20 Brookhollow Ave telephone 02 8850 2888 www.firesense.com.au Baulkham Hills NSW 2153
More information4 wire conventional alarm system
Scimitar 4 wire conventional alarm system from Channel Safety Systems Scimitar 4 wire conventional alarm system The Scimitar Fire Alarm Control System is a comprehensive range of high specification conventional
More informationBiWire Flexi. BiWire Flexi Fire Panel EFBW8ZONE-FLEXI / EFBW4ZONE-FLEXI / EFBW2ZONEFLEXI Installation Manual
BiWire Flexi BiWire Flexi Fire Panel EFBW8ZONE-FLEXI / EFBW4ZONE-FLEXI / EFBW2ZONEFLEXI Installation Manual Contents Contents 1. INTRODUCTION... 4 1.1 Purpose...4 2. THE BIWIRE FLEXI FIRE DETECTION & ALARM
More informationFEC400 Series. Installation Manual
FEC400 Series Conventional microprocessor controlled fire detection and alarm panels with extinguishing control Installation Manual Version 2.3 / August 2004 Aritech is a GE Interlogix brand. http://www.geindustrial.com/ge-interlogix/emea
More informationINDEX 1- Introduction The Control Pane...7l 4.1- The Control Panel 1 and 2 Loops The Control Panel 4 and 8 Loops...
GUIDE MANUAL INDEX 1- Introduction...5...5...6 4- The Control Pane...7l 4.1- The Control Panel 1 and 2 Loops...7 4.2- The Control Panel 4 and 8 Loops...9 5- Installation Guide...10 5.1- Pre-Installation
More informationUSER MANUAL COMBINED FIRE & EXTINGUISHING CONTROL PANEL COMPLIES WITH BS EN PART 1 & EN54 PARTS 2 & 4
PREMIER EX8 EXTINGUISHING PANEL USER MANUAL COMBINED FIRE & EXTINGUISHING CONTROL PANEL COMPLIES WITH BS EN 12094 PART 1 & EN54 PARTS 2 & 4 USER MANUAL Approved Document No: GLT.MAN-132 INDEX Extinguishing
More informationOperating manual and Log book for the range of 1,2,4 and 8 zone fire Control and Repeat panels
Operating manual and Log book for the range of 1,2,4 and 8 zone fire Control and Repeat panels The panels are designed in accordance with the requirements of EN54 Part 2:1997 (and include optional clauses
More informationFIREPRO INSTALLATION MANUAL FIRE ALARM CONTROL PANEL INSTALLATION MANUAL. Approved Document No. GLT Issue: 1. 8 Author: NRPJ Date: 7/ 3/201 4
FIRE ALARM CONTROL PANEL INSTALLATION MANUAL Approved Document No. GLT -201-7-3 Issue: 1. 8 Author: NRPJ Date: 7/ 3/201 4 CONTENTS 1. INTRODUCTION... 1.1 HANDLING THE PCBS... 1.2 USING THIS MANUAL... 1.3
More information2000 Series Sensors Installation Guide
2000 Series Sensors Installation Guide Revision 5.1: August 2000 (unreleased) Aritech is a trademark of SLC Technologies B.V. COPYRIGHT SLC Technologies B.V. 2000. All rights reserved. SLC Technologies
More informationFire Control Panel FS4000
Fire Control Panel FS4000 INSTRUCTION MANUAL Revision 11/01.17 Contents 1. Introduction... 3 2. Terminology... 3 3. Function... 4 4. Technical features... 4 4.1 Fire alarm lines... 4 4.2. Current thresholds
More informationZerio Plus EDA-R6000 Radio Combined Optical Smoke Detector and Sounder Installation Instructions
Zerio Plus EDA-R6000 Radio Combined Optical Smoke Detector and Sounder Installation Instructions EN54-3:2001+A1:2002+A2:2006 EN54-7:2000+A1:2002+A2:2006 EN54-25:2008 0359 Electro Detectors Ltd. Electro
More informationLF-4000 Series Conventional Fire Alarm Control Unit
LF-4000 Series Conventional Fire Alarm Control Unit Features: 1 to 36 Zone Control Panels Control Key Switch Easy Push Button Control Switches Zone Circuit Monitoring for Open and Short Sounder Circuit
More informationIndustries. As a premier global manufacturing company, we believe that great brands are
JSB Fire Systems ONE COOPER Every day, thousands of people all over the world use products made by Cooper Industries. As a premier global manufacturing company, we believe that great brands are built on
More informationConventional Smoke Detectors KFAPO
Kingfisher Company, inc. Conventional Smoke Detectors KFAPO Features: Wide operating voltage, 9-33 VDC Advanced electronic technology Flashing LED Magnetic test switch Proven detection performance Designed
More informationEvacU Emergency Warning Control and Indicating Equipment (Occupant Warning Systems) Technical Manual MAN3072-9
EvacU Emergency Warning Control and Indicating Equipment (Occupant Warning Systems) Technical Manual MAN3072-9 TABLE OF CONTENTS Section Page No. 1 About This Manual... 3 1.1 Introduction... 3 1.2 References...
More informationEvacU Emergency Warning Control and Indicating Equipment (Occupant Warning Systems) Technical Manual MAN3072-5
EvacU Emergency Warning Control and Indicating Equipment (Occupant Warning Systems) Technical Manual MAN3072-5 MAN2995-2 05/09/12 TABLE OF CONTENTS Section Page No. 1 About This Manual... 3 1.1 Introduction...
More informationReflective Optical Beam Smoke Detector User Guide
Reflective Optical Beam Smoke Detector User Guide 1. Installation IMPORTANT NOTE: The infrared beam path MUST be kept clear of obstructions at all times! Failure to comply may result in the system initiating
More informationone Operating instructions SenTRI ONE panel-based Fire detection and alarm system
SenTRI ONE panel-based Fire detection and alarm system one 042bc/14 4188-978 issue 2_04-10_SenTRI ONE system oper Part of Document pack 2535-235 issue 2 1 Contents User responsibility - - - - - - - - -
More informationDiscovery 1-4 Loop 32 Zone, 40 Character Analogue Addressable Control Panel. Application Guide
Discovery 1-4 Loop 32 Zone, 40 Character Analogue Addressable Control Panel Application Guide Contents Page 1.0 Introduction and Typical System Illustration 2 2.0 Cabinet Specifications 4 3.0 Hardware
More informationTechnical Data Sheet
Mx-1000 Series Technical Data Sheet Application Guide for Mx-1002, Mx-1004, Mx-1008, Mx-1016 & Mx-1032 Conventional Fire Alarm Control Panels And Mx-1108, Mx-1116 & Mx-1132 Repeater Panels Document Number:
More informationFire Control Panel. Installation & Programming Manual TABLE OF CONTENTS
Fire Control Panel Installation & Programming Manual TABLE OF CONTENTS Page Getting Started 2 Power Supply Unit 3 Remote Keypad Bus 3 Inputs & Outputs 4 User Keypad Functions 5 Engineer Keypad Functions
More informationAddressable and Conventional Fire Protection
Addressable and Conventional Fire Protection Simply reliable F I R E P R O T E C T I O N The MAGPro and Fireline systems has been created to balance performance, reliability and aesthetics whilst being
More informationDocument No Issue 4 user manual
DX Document No. 996-148-000-4 Issue 4 user manual Dimension Series Table of Contents 1 INTRODUCTION... 5 1.1 NOTICE... 5 1.2 MODELS... 5 1.3 WARNINGS AND CAUTIONS... 7 1.4 NATIONAL APPROVALS... 7 1.5 EN54
More informationGST Headquarters. GST Production Base
GST Headquarters GST Production Base Company Profile GST, a high tech company, is specialising in R&D, manufacturing, marketing and technical service of Fire Alarm Systems. GST manufactures over 6 million
More information