Tek-ENTRY Vandal-Resistant Apartment Entry Systems. Specification Sheets Submittal Package. as of 03/24/2009. Website:

Transcription

1 Tek-ENTRY Vandal-Resistant Apartment Entry Systems s Submittal Package as of 03/24/2009 Website: tektone@tektone.net For Technical Assistance: Technical Assistance teksupt@tektone.net 277 Industrial Park Road Franklin, NC (828) (800) Fax (828) Copyright TekTone Sound & Signal Mfg., Inc., All rights reserved. No part of these publications may be copied without the express written permission of TekTone Sound & Signal Mfg., Inc. The contents of these specification sheets are furnished for informational use only, are subject to change without notice, and should not be construed as a commitment by TekTone Sound & Signal Mfg., Inc. TekTone Sound & Signal Mfg., Inc. assumes no responsibility or liability for any errors or inaccuracies that may appear in this documentation. TekTone, the TekTone logo, Tek-Call, Tek-Care, Tek-Check-In, Tek-Com, Tek-Digicare, Tek-Door, Tek-Entry III, Tek-Guard, Tek-Micro, Tek-Micro II, Tek-MMARS II, Tek-NIOS, Tek-NIOS II, Tek-Paging, Tek-Phone, Tek-Safe, Tek-Select II, Tek-Sentry, Tek-Sound, Tek-Status and Tek-View are either registered trademarks or trademarks of TekTone Sound & Signal Mfg., Inc. in the United States and/or other countries. All other trademarks are the property of their respective owners.

2 AM193, AM493 Series Speaker/Microphone Entrance Panels IL319 Rev. 6-06/2004 The AM193 and AM493 series Speaker/Microphone Entrance Panels are modular series for use with TekTone s TA205B handset intercom suite stations. The panels are equipped with a voice frequency response speaker and microphone, and can accommodate up to 16 buttons per panel. For more than 16 suites, the AM193 is used in conjunction with an AM190/12 or AM190/22 button adder panel, while the AM493 is used with an AM490/12 or AM490/22 button adder panel. The AM193 and AM493 series Speaker/Microphone Entrance Panels and TA205B handset intercom suite stations provide two-way communication between the building entrance and suite, in addition to telephonic privacy and hands-free loudspeaking at the entrance. Controlled entry is permitted by push button operation of the electric door release in the handset, if desired. TekTone s AM193 and AM493 panels with 2 8 buttons are available with postal release option. AM193 Series Entrance Panel (AM193/16 shown) AM493 Series Vandal-Resistant Entrance Panel (AM493/16 shown) The entrance panel shall be TekTone s AM193 or AM493 series Speaker/Microphone Entrance Panel or approved equal and shall provide for up to 16 push buttons per panel. The panel shall contain name and suite (or apartment) number card holders for button identification. The panel shall be flush or surface mounted and shall be finished in brushed aluminum. Modular design Hands-free loudspeaking Weather-resistant speaker Easily accessible name holders Dimensions: Push button: Speaker: Construction: Flush Mount: Surface Mount: S Height: 16.5" (413 mm) Width: 4" (100 mm) each panel Individually replaceable with selfwiping contacts 2.5" (64 mm) voice frequency response Modular extruded, anodized aluminum panel with high-impact grill OH190 series housing and OF190 series frame OF190S series frame AM193, AM493 series PK205 SS102A or SS105B TA205B Entrance Panel Amplifier Transformer Handset Suite Station

3 Tek-ENTRY AM642 Series Vandal Resistant Entrance Panels IL524 Rev. 7-03/2008 The AM642 Series Vandal-Resistant Entrance Panel is for use with TekTone loud-speaker type suite stations. The anodized aluminum panel is available in two sizes. The 4.75" 11.25" panel accommodates 2 to 8 push buttons, and the 4.75" 17.25" panel is used for applications requiring 10 to 16 push buttons or a postal release option. Panels are equipped with a weather-resistant Mylar speaker protected by a louvered panel and perforated aluminum material. The speaker panel can accommodate up to 16 push buttons and actuators. In addition, the panel also contains up to 16 name holders with plastic lenses that snap easily into the panel and are individually replaceable. AM642 Series Entrance Panels The entrance panel shall be TekTone AM642 Vandal- Resistant Series or approved equal, and shall provide for up to 16 push buttons per speaker panel. The panel shall include a weather-resistant Mylar speaker mounted behind a louvered panel and perforated aluminum material to protect the speaker from damage. Push button switches shall be individually replaceable with self-wiping contacts. The push button actuator shall be made of solid, extruded aluminum. In addition, the panel shall contain up to 16 individually replaceable name holders. The name holders shall be made of black flame-retardant polycarbonate plastic with clear flame retardant polycarbonate plastic lenses to protect card inserts. The AM642 shall have top and bottom decorative end caps that shall also serve as mounting brackets to allow flush or surface mounting. The decorative end caps shall be made of black flame retardant polycarbonate plastic. Each AM642 Panel, or approved equal, shall be supplied with name card sheets that may be easily separated into individual name strips. Name strips shall be inserted into name holders without the use of tools. Vandal-resistant panel and push button actuators Hands-free loud-speaking Weather-resistant Mylar speaker Self-wiping push button switches Decorative end caps Individually replaceable name holders Slim-line surface-mount option Simple installation S Dimensions: Height: 11.25" or 17.25" ( S suffix denotes surface mount) Width: 4.75" Push button: Individually replaceable type with self-wiping contacts Speaker: 2.5" (64 mm) voice frequency response Construction: Anodized extruded aluminum panel Housings, flush: OH600 Back Box for 11.25" panel OH601 Back Box for 17.25" panel Surface mount: Add S to panel part number, (i.e., AM642/10S). Name holders: 2.125" " IR100/200 Series: PK543A SS102A (or SS105B) Apartment Stations Amplifier Transformer

4 Tek-ENTRY AM492 Vandal Resistant Apartment Intercom System IL462 Rev /2008 The AM492 Series Vandal Resistant Apartment Intercom System Entrance Panel is a modular series for use with TekTone apartment intercom stations. Panels are equipped with a Mylar, voice-frequency response speaker protected by a louvered panel and perforated aluminum material. The speaker panel can accommodate up to 18 push buttons. For more than 18 apartments, the AM492 is used with the AM490/12 or AM490/22 push button add-on panel. Pressing the button corresponding to the desired name and apartment number causes a buzzing at the apartment station. The resident may then converse with the caller. Controlled entry is permitted by push button operation of the electric door release. AM492 panels with 0 10 buttons are available with postal option. AM492 Series Entrance Panel shown with OF191 frame The apartment intercom system entrance panel shall be TekTone AM492 Vandal Resistant Series or approved equal, and shall provide for up to 18 push buttons per speaker panel. The panel shall include a weather-resistant Mylar speaker mounted behind a louvered panel and perforated aluminum material to protect the speaker from damage. Push button switches shall be individually replaceable type with selfwiping contacts. Push button actuators shall be made of solid, extruded aluminum. In addition, the panel shall contain up to 18 individual name holders. The name holders shall be made of black flame-retardant polycarbonate plastic with clear flame retardant polycarbonate plastic strips to protect card inserts. Each name holder shall snap into two small slots on the panel itself and shall be individually replaceable. The panel shall be flush or surface mounted and shall be finished in brushed aluminum. Vandal resistant panel and push button actuators Weather-resistant Mylar speaker Fully-enclosed back box with knockouts Modular design Hands-free loudspeaking Individually replaceable name holders (black flame retardant polycarbonate plastic) Self-wiping push button switches Slim-line surface mount option S Dimensions: Height: 16.5" (419 mm) Width: 4" (102 mm) each panel Speaker: 2.5" (64 mm) Mylar Push Button: Individually replaceable with self-wiping contacts. Construction: Modular extruded, anodized aluminum panel and push button actuators. Housings: OH190 Series for flush mounting. OF190S Series frame for surface mounting. IR Series OF Series OH Series PK543A SS Series Apartment Intercom Stations Frames Housings Amplifier Transformers

5 CM402 Series Stainless Steel Panel IL712 Section E Rev. 6-12/2005 CM402 Stainless Steel Vandal-Resistant Entrance Panels are rugged, attractive panels for use indoors and outdoors. They are made of heavy 16-gauge high-carbon stainless steel, for vandal resistant applications. CM402 panels are custom made to customer s exact size and layout specifications (maximum panel size is 18"H 24"W). Panels are available in three flush mount edges (flat, slight bevel, or ½" folded please specify) and a surface mount edge (1½" folded add suffix S to part number). Other available options are built-in or separate stainless steel directory (add suffix D ), name holder directory option (add suffix N ), built-in postal release switch (PO402I), built-in CCD camera (CM402CAM), and a variety of microphone and handset options. CM402 Series The entry panel shall be TekTone s CM402 series, or approved equal. The panel shall be flush or surface mount type and shall include the proper speaker components to match the apartment intercom stations. The panel shall have integral and separate directory options if a directory is required. Where supplied, the directory unit shall be made of heavy-gauge brushed stainless steel and include a name strip holder covered by a protective sheet of clear polycarbonate. The directory shall be panel mounted, and shall require the use of button pin in head Torx screwdriver tools. The entry panel shall include a size TT25 Torx tool bit for directory insertion (if applicable) and a size TT15 Torx tool bit for panel installation/maintenance. The panels shall have bright nickel push button plungers, engraved apartment markings, and perforated aluminum material for speaker component protection. The panel shall be made of a single sheet of 16-gauge high-carbon stainless steel. CM402 panels feature metal push button plungers, engraved apartment markings and engraved building name or logo and/or company name or logo (where space allows). The use of Torx button pin in head screws makes directory or panel tampering nearly impossible without the use of the included special Torx tool bits. Heavy 16-gauge high-carbon stainless steel panel Bright nickel push-button plungers Custom engraved Integral directory protected by thick polycarbonate Rugged, attractive, tamper and vandal resistant Variety of speaker, microphone and handset options Works with a wide variety of apartment entry systems Flush or surface mountable Dimensions: Construction: Tool Required: S Per customer specifications Heavy 16-gauge high-carbon stainless steel faceplate. Torx screwdriver tips included for panel installation/removal (size TT15) and directory name insertion (size TT25). Dependent upon panel configuration. Flush panels are available with or without matching flush backbox/housing. Contact our sales department for more information.

6 Tek-ENTRY Vandal Resistant Apartment Entry Panels IL500 Rev. 8-03/2008 CM492/024 OF192 Frame and AM190D Directory CM491/016 OF291 Frame The entrance panel shall be TekTone 's vandal resistant CM491 series or CM492 series. CM492 shall contain as many engraved plungers as there are apartments or areas to be called. CM491 shall contain 4, 8, 12, 16 or 20 engraved plungers. Directory panels shall be supplied to accommodate an equivalent number of tenant names. The panel shall include a weather resistant Mylar speaker mounted behind a louvered grill and perforated aluminum material to protect the speaker from damage. Push button switches shall be individually replaceable with self-wiping contacts. Push button actuators shall be made of solid, extruded aluminum suitable for engraving. All mounting screws shall be tamper resistant. The panel shall be flush or surface mounted and shall be finished in brushed aluminum. The CM492 series vandal resistant apartment entry panels are modular so that adding additional button panels (if required), directory panels, frame and housing will comprise a complete entrance panel. The CM491 series vandal resistant apartment entry panel is available with 4, 8, 12, 16 or 20 buttons and includes an integral directory. Panels are equipped with a Mylar voice-frequency response speaker protected by a louvered grill and perforated aluminum material. The aluminum push button actuators may be engraved with up to four letter/digit combinations. Vandal resistant panel and push button actuators Weather resistant Mylar speaker Fully enclosed back box with knockouts Hands-free loudspeaker (or optional handset) Engraveable solid aluminum and push button actuators Vandal resistant Lexan directories* Slim-line surface mount frame option Tamper resistant mounting screws S Dimensions: Height: 16.5" (418 mm) Width: 4" (100 mm) Speaker: 2.5" (63.5 mm) Mylar Construction: Modular extruded anodized aluminum Flush Mount: CM491 OF291 frame, OH191 housing CM492 OF190 series frame, OH190 series housing Surface Mount: CM491 OF291S frame CM492 OF190S series frame Plungers: Engraved extruded aluminum Push Button: Individually replaceable with self-wiping contacts AM190D IR series PK543/A RP055EN SS Series OF/OH Series *Note: COMPONENTS Directory Panel Speaker-type Remote Stations Amplifier Apartment Number Button Engraving Transformer Frame & Housing Lexan is a Registered Trademark of General Electric Corporation.

7 IR402 Apartment Intercom Station IL733 Rev. 4-05/2004 The IR402 vandal resistant apartment intercom station is designed for renovation, new installation and other applications that require a heavy duty, customizable station (minimum order is 10 pieces). The customer or installer will specify the width and height of the panel, as well as the sizes, number and locations of the mounting holes. The dimensions between speaker, circuit board and buttons will remain the same without regard to overall panel dimensions. TALK LISTEN DOOR IR402 The caller, by pressing the appropriate button on the entrance panel, causes an electronic tone to be heard at the apartment station. The tenant responds by pushing the TALK button while speaking to the caller, the LISTEN button while waiting for a reply, and the DOOR button to allow entry to the building. Simple operation Customizable configuration Vandal resistant construction S Suite stations shall be TekTone IR402 or approved equal. The IR402 is a custom remote station that is built to specifications provided by the customer as to the physical dimension of the panel, and the size, location and number of mounting holes. If the customer has no specific size requirements, the default size shall be the minimum of 4.5" high 4.625" wide. Maximum height is 9" (229 mm) Heavy duty momentary push buttons mounted on heavy gauge stainless steel shall be provided for TALK, LISTEN and DOOR operations. The speaker/microphone shall be a 2.5" 2.5" highsensitivity type, and connections to the station shall be made with provided plug-on wire harness connectors. The dimensions between speaker, circuit board and buttons shall remain consistent. Dimensions: Height: Minimum 4.5" (114 mm) Maximum 9.0" (229 mm) Width: Minimum 4.625" (117 mm) Construction: Stainless steel faceplate Controls: Heavy duty vandal resistant steel plunger Speaker/Mic: push buttons. 2.5" (63.5 mm) 2.5" (63.5 mm) with voice response. Also used for electronic tone signal. Mounting: Station will fit a minimum cutout of 3" (76 mm) " (90.5 mm). Mounting holes are located as specified by customer to fit almost any existing box. Cannot be mounted to a single gang box and/or ring. Tek-PHONE -or- Tek-GUARD PO001 Apartment Entry Systems Electric Door Opener

8 IR085B Apartment Intercom Station IL614 Rev. 5-06/2007 The IR085B Apartment Intercom Station is designed specifically for renovation use and is large enough to cover the area occupied by most existing intercom units, making repainting unnecessary. The reduced wiring requirement permits using the existing wiring (if in good condition), while the advanced electronic design permits use in large or small buildings. A wide variety of optional accessories are available to provide additional functions, such as dual entrance operation, post office door release, silent door operation, etc. IR085B Pressing the appropriate button on the entrance panel causes an electronic call tone to be heard in the apartment stations. The tenant responds by pushing the TALK button while speaking to a caller, the LISTEN button while waiting for a reply, and the DOOR button to allow entry to the building. Simple push button operation Automatic privacy Easy installation Large panel covers most openings Suite stations shall be TekTone IR085B, or approved equal, and shall be large enough to cover the area occupied by the previous intercom unit. Momentary action push buttons shall be provided for TALK, LISTEN and DOOR operations. The speaker/microphone shall be 3.5" (89 mm) high-sensitivity type with voice-frequency response. Screw terminal connections shall be provided and required wiring shall be just three common wires and one selective wire. S Dimensions: Width: 8.75" (222 mm) Height: 6.5" (165 mm) Construction: Steel faceplate with white vinyl coat. Controls: Individually replaceable push buttons with self-wiping plated contacts., identified for TALK, LISTEN and DOOR functions. Speaker/Mic: 3.5" (89 mm) with voice response, also used for electronic tone signal. Mounting: Mounting holes may be positioned to accommodate an existing back box. Supplied without holes or mounting screws, unless custom ordered. PK543A Amplifier PO001 Door Release SS102A, SS105B Transformer AM192, CM192, AM600 Series Entrance Panel

9 IR086S Apartment Intercom Station IL503 Rev. 7-03/2008 The IR086S Apartment Station is designed specifically for replacement of 3311-type apartment intercom stations, and is large enough to cover the area occupied by most existing units, making repainting unnecessary. The caller, by pressing the appropriate button on the entrance panel, causes an electronic call tone to be heard in the apartment station. The tenant responds by pushing the TALK button while speaking to the caller, the LISTEN button while waiting for a reply, and the DOOR button to allow entry to the building. Simple push button operation Easy installation IR086S Suite stations shall be TekTone IR086S, or approved equal, and shall be large enough to cover the area occupied by the previous intercom. Momentary-action push buttons shall be provided for TALK, LISTEN and DOOR operations. The speaker/microphone shall be a 3.5", high-sensitivity type with voice-frequency response. Pigtail or plug-in terminal connections shall be provided. S Dimensions: Height: 6.875" (175 mm) Width: 6.125" (155 mm) Construction: Steel faceplate with white vinyl coat. Controls: Individually replaceable type push buttons with self-wiping, plated contacts. Identified TALK, LISTEN, and DOOR functions. Speaker/Mic: 3.5" (89 mm) with voice response. Also used for electronic tone signal. Mounting: Mounting holes are positioned to accommodate an existing surface or flush back-box. Supplied with holes and mounting screws.

10 IR087A Apartment Intercom Station IL723 Rev. 3-06/2007 The IR087A Apartment Station is designed specifically for renovation use and is large enough to cover the area occupied by most existing intercom units, making repainting unnecessary. The reduced wiring requirement permits using the existing wiring (if in good condition), while the advanced electronic design permits use in large or small buildings. A wide variety of optional accessories is available to provide additional functions, such as dual entrance operation, post office door release and silent door operation. Simple push button operation Automatic privacy Easy installation Large panel covers most openings S IR087A Suite stations shall be TekTone IR087A, or approved equal, and shall be large enough to cover the area occupied by the previous intercom unit. Momentary action push buttons shall be provided for TALK, LISTEN, and DOOR operations. The speaker/microphone shall be 3.5" highsensitivity type with voice-frequency response. Screw terminal connections shall be provided and required wiring shall be only three common wires and one selective wire for IR087A stations. Dimensions: Height: 8.75" (222 mm) Width: 6.5" (165 mm) Construction: Steel faceplate with white vinyl coat. Controls: Individually replaceable type push buttons with self-wiping plated contacts. Identified for TALK, LISTEN, and DOOR functions. Speaker/Mic: 3.5" (89 mm) with voice response. Also used for electronic tone signal. Mounting: Mounting holes may be positioned to accommodate an existing back box. Supplied without holes or mounting screws, unless custom ordered. PK543A PO001 SS102A, SS105B AM192, CM192, AM600 Amplifier Door Release Transformer Series Entrance Panel

11 IR102C Suite Station IL490 Rev /2006 The IR102C Suite Station allows the tenant to press a button to talk and then release the same button to listen. This eliminates the necessity of pressing one button to talk and another button to listen. The station automatically shuts off a few seconds after conversation is completed, or as soon as the door button is pressed. The IR102C is not a voice/noise activated intercom station and does not require a complex and costly amplifier. One combination TALK/LISTEN button Eliminates two-button talk/listen operation Uses standard amplifier power pack English text, international symbols and Braille S IR102C Suite station shall be TekTone IR102C or approved equal, and shall provide circuitry for communications, signaling, and door release operation. Talk and listen functions shall require operation of a single push button. The speaker shall be a voice frequency response type. Electronics shall be securely mounted on a printed circuit board. Wiring shall be via screw terminals. Dimensions: Height: 6.875" (174.6 mm) Width: 5" (127 mm) Depth: 1.5" (38.1 mm) Projects: 1" (25.4 mm) from mounting surface Finish: Molded of high-impact ABS plastic AM/CM Series PK543A SS102A, SS105B IH102, IH101 Speaker/Button Panels Amplifier Transformer Ring or Housing

12 IR103E, IR104E, IR105E Apartment Intercom Stations IL486 Rev /2006 The IR103E, IR104E and IR105E Apartment Intercom Stations combine modern styling with ease of operation to provide natural, clear voice communication and positive door-release operation. The attractive, flame-retardant ABS plastic faceplates are flush mounted and blend with any setting. The advanced circuitry and versatility permit use in large or small buildings, with one or several entrances. A wide variety of optional accessories is available to provide additional functions, such as multiple entrance operation and post office door release. IR103E, IR104E, IR105E Suite stations shall be TekTone s IR103E, IR104E or IR105E. The stations shall be equipped with momentaryaction push buttons for talk, listen and door operation. Buttons shall be labeled in English, and with both international and Braille symbols. The speaker/microphone shall be a 2.5" high-sensitivity type with voice-frequency response. The station shall have an attractive, flameretardant ABS plastic faceplate with screw terminal connections. Required wiring shall be just 2 common and 1 selective wires for the IR103E station; 3 common and 1 selective wires for the IR104E station; and 4 common and 1 selective wires for the IR105E station. Flush mounting Simple, push button operation Easy installation Advanced design Automatic privacy Clear voice quality Precision-engineered for reliability English text, international symbols and Braille S Dimensions: Height: 6.875" (175 mm) Width: 5" (127 mm) Depth: 1.25" (32 mm) Finish: Controls: Speaker/Mic: Connection: Housings: AM/CM Series PK543A SS Series Flame-retardant ABS plastic. Individually replaceable push buttons with self-wiping contacts. Identified for talk, listen and door functions. 2.5" (89 mm) with voice response. Also used for electronic tone signal. Screw terminals IH102 ring or IH101 box Entrance Panels Amplifier Transformers

13 IR203E, IR204E, IR205E Apartment Intercom Stations IL233 Rev /2006 The IR203E, IR204E, IR205E Apartment Intercom Stations combine modern styling with ease of operation to provide natural, clear voice communication and positive door-release operation. The attractive flame-retardant ABS plastic faceplates are surface mounted, and blend with any setting. The advanced circuitry and versatility permit use in large or small buildings, with one or several entrances. A wide variety of optional accessories is available to provide additional functions, such as multiple entrance operation and post office door release. IR203E, IR204E, IR205E Surface mounted Simple, push button operation Easy installation Advanced design Automatic privacy Clear voice quality Precision-engineered for reliability English text, international symbols and Braille S Apartment intercom stations shall be TekTone s IR203E, IR204E or IR205E. The stations shall be equipped with momentary-action push buttons for talk, listen and door operation. Buttons shall be labeled in English, and with both international and Braille symbols. The speaker/ microphone shall be a 2.5" high-sensitivity type with voice-frequency response. The station shall have an attractive, flame-retardant ABS plastic faceplate with screw terminal connections. Required wiring shall be just 2 common and 1 selective wires for the IR203E station; 3 common and 1 selective wires for the IR204E station; and 4 common and 1 selective wires for the IR205E station. Dimensions: Height: 6.875" (175 mm) Width: 5" (127 mm) Depth: 1.25" (32 mm) Finish: Controls: Speaker/Mic: Connection: Housings: AM/CM Series PK543A SS Series Flame-retardant ABS plastic. Individually replaceable push buttons with self-wiping contacts. Identified for talk, listen and door functions. 2.5" (62.5 mm) with voice response. Also used for electronic tone signal. Screw terminals standard. Single-gang ring or single-gang electrical box. Entrance Panels Amplifier Transformers

14 IR207B 4-Wire Apartment Station IL183 Rev /2008 The IR207B Apartment Stations are rugged, dependable units combined with advanced electronic design to provide natural, clear voice communication and positive door release operation. These versatile stations may be used in large or small buildings and feature a wide variety of optional accessories to provide needed additional functions, such as multiple entrance, post office door release, timed door release operation, etc. Simple push button operation Easy installation Advanced design Automatic privacy Clear voice quality Rugged and reliable IR207B Suite stations shall be TekTone IR207B or approved equal, with a rugged stainless steel panel and momentary action push buttons for talk, listen and door operation. The 2.5" 2.5" speaker/microphone shall have voice-frequency response and shall be secured by stainless steel studs. Screw terminal connections shall be provided. Required wiring shall be just 3 common and 1 selective wires. S Dimensions: Height: 4.5" (115 mm) Width: 4.5" (115 mm) Finish: Satin brushed stainless steel Controls: Individually replaceable push buttons with self-wiping contacts. Identified for TALK, LISTEN and DOOR functions. Speaker/Mic: 45 ohms, 2.5" 2.5" Connections: Screw terminals Housing: Standard 2-gang electrical box Wiring: 3 common and 1 selective PK543/A PO001 CM192 or AM192 SS102A or SS105B Amplifier Door Release Entrance Panel Transformer

15 LI404B Strobe IL544 Section E Rev. 7-11/2005 The LI404B Strobe is a high-intensity remote visual signaling device for use with TekTone PK543, PK205 and PK104B Amplifier Apartment Systems, and with TekTone PK502B Transfer Relays. The unit is primarily for use in locations where hearing-impaired persons require supplemental call notification, but can be used anywhere a visual indication of an incoming call is desired. The bright strobe light flashes for approximately seconds when an incoming call is detected. The device can be installed in most standard single or double gang electrical boxes or similar indoor openings. It is not a weatherproof device and therefore should not be used for any outdoor applications. Installation is facilitated by the use of simple connections to the pre-mounted circuitry and a complement of mounting hardware. LI404B Supervised Corridor Light The LI404B Strobe Light portion meets ADA and UL 1971 requirements. S Strobe light shall be TekTone LI404B or approved equal. Operation shall be accomplished by placing a call to a remote station. The strobe light shall flash for approximately seconds upon detection of the incoming call signal. The strobe light shall have a brightness of 15 candela per UL 1971 (75 candela per UL 1638). It shall be encased in an attractive, flame retardant (UL 94V-0) plastic housing. The strobe light shall meet ADA and UL requirements for signaling appliances. Dimensions: Height: 5.5" (140 mm) Width: 4.5" (114 mm) Depth : 3.5" (89 mm) Projects: 2.5" (63.5 mm) from mounting surface Construction: Attractive, flame-retardant (UL 94V-0) plastic housing Strobe: 15 candela per UL 1971 Power: 24 VDC, 57 ma DC nominal Wiring: 18 gauge minimum, 750' maximum Installation: Standard single or dual gang box PK amplifier system: includes PK543, PK205, and related system components (PK502B Transfer Relays, IR & TA Remote Stations, CM & AM Entrance Panels)

16 PK124 Battery Charger IL818 Section E Rev. 2-10/2004 C B P T1 T2 PK124 The PK124 Battery Charger, when used in conjunction with two BA VDC batteries, provides continuous battery charging so that if power to system equipment is interrupted, standby operating power is provided for up to approximately 6 hours. (Time may vary depending on system size and usage.) TekTone systems supported by the PK124 include the DS100 Door Sentry & Emergency Alarm System and the CM800 Emergency Call System. The PK124 may also be used for battery backup on all TekTone apartment entrance system amplifiers. Low voltage operation Reliable alternate power supply Integrated circuit design Easy installation S The battery charger shall be TekTone PK124 or approved equivalent, and shall be used in conjunction with two TekTone BA VDC batteries, or approved equivalent. The PK124 shall provide continuous battery charging for approximately 6 hours for uninterrupted equipment operation during power failures. Screw terminals shall be provided for connections. The PK124 Battery Charger shall be of rugged construction and modular integrated circuit design. Dimensions: Height: 9.5" (240 mm) Width: 2.375" ( 60 mm) Depth: 2.25" ( 57 mm) Construction: Rugged extruded aluminum case housing, quality electronic components mounted on PCB Power: 24 VAC, 30 VA provided by SS106 transformer Connection: Screw terminals Mounting: Surface CM800 or DS100 Emergency Call System Door Sentry & Emergency Alarm System

17 IH151N Housing IL646 Section E Rev. 4-03/2008 The IH151N Housing is used as a central junction point for wiring in the CM800 and Tek-CARE NC110, NC150, NC200 systems. Knockouts are included on all sides except lid to allow the connection of electrical conduit from any direction. In addition, the lid has a knockout which can be used to install an optional key lock the TekTone HW231 or equivalent. A single-gang electrical junction box is mounted inside the main enclosure to allow protected electrical connections to be made. The enclosed electrical junction box is galvanized steel with a stainless steel cover plate. IH151N Housing Maintenance free Easy Installation 19-gauge steel construction Knockouts provided UL 1069 Listed when constructed with PK151A Annunciator Power & Control Unit and SS106 Transformer Housing shall be TekTone IH151N housing or approved equal. The IH151N housing shall be of steel construction for durability. It shall include a single-gang metal junction box to protect electrical connections. Knockouts shall be provided on all sides except lid to facilitate easy connection of electrical conduit. The lid shall have a knockout for an optional key lock TekTone HW231 or equivalent. All exposed surfaces shall be either stainless steel or painted to protect against oxidation. The outer enclosure shall be composed of 19-gauge cold-rolled steel. S Dimensions: Height: 11.75" (300 mm) Width: 11.75" (300 mm) Depth: 3.75" (96 mm) Construction: 19 gauge, cold-rolled steel

18 Wiring Diagrams for PK124 Battery Charger IL426 Section E Rev. 8-09/2004 PK124 to PK151A (NC110N, NC150N, NC200N) Interconnect Wiring Diagram PK151A J D R R PP T1 T2 N N Q Q E C B P T1 T2 PK124 4 AMP FUSE VAC SS106 TWO 12V GEL CELL BATTERIES PUT IN SERIES 2.5 AMP HOUR 117 VAC Copyright TekTone Sound & Signal Mfg., Inc. All Rights Reserved. IL426 PK124 to PK151A Interconnect Wiring Diagram Rev Notes: 1. Do not connect transformer to PK151A. 2. Use 24 VAC connections on SS106 transformer. 3. All wiring #18 unless shown. 4. See installation manual for additional PK151A connections.

19 PK124 to PK2019 (CM800, CM900) or SK109 (DS100) Interconnect Wiring Diagram PK2019 R1 R2 R3 B A W PK124 C B P 4 AMP FUSE TWO 12V GEL CELL BATTERIES PUT IN SERIES 2.5 AMP HOUR SK019 C T DP S P D N T1 T2 T1 T VAC SS VAC IL426 PK124 to PK2019 or SK019 Interconnect Diagram REV Notes: 1. Do not connect transformer to PK2019 or SK Use 24 VAC connections on SS106 transformer. 3. All wiring #18 unless shown. 4. See installation manual for additional PK2019 or SK019 connections. PK124 to PK400 Interconnect Wiring Diagram Notes: 1. Do not connect transformer to PK Use 24 VAC connections on SS106 transformer. 3. All wiring #18 unless shown. 4. See installation manual for additional PK400 connections. Copyright TekTone Sound & Signal Mfg., Inc. All Rights Reserved.

20 PK205 Intercom Amplifier IL246 Rev. 8-03/2008 The PK205 Intercom Amplifier is designed for use with the TA205B Handset Intercom Suite Station and provides the amplification, control and power circuits needed to operate a complete apartment intercom system. Using solid-state technology and constructed with high-quality components, this amplifier is designed for long-lasting reliable performance. Optional accessories are available to provide additional functions such as dual-entrance operation, post office door release, etc. Low voltage operation Rugged aluminum construction Volume adjustment Easy installation S PK205 Intercom Amplifier The intercom amplifier shall be a TekTone PK205 or approved equal, and shall provide the control, amplification and power circuits to operate the entire intercom system. The amplifier shall have rugged aluminum construction, adjustable volume, and balanced input. Low voltage wiring shall be used and screw terminals shall be provided for ease of installation. Dimensions: Height: 9.5" (240 mm) Width: 2.375" (60 mm) Depth: 2.25" (57 mm) Construction: Rugged extruded aluminum case housing quality electronic components on a printed circuit board Amplification: Solid-state circuitry Door Switching: Heavy-duty relay with nylon dust cover (buzzing operation) Controls: Volume adjustment Connections: Mounting: Screw terminals Surface (usually installed in entrance panel housing) Power Required: 16 volts AC 10 VA Temperature: 0 C 50 C AM193 or AM493 Series PO001 SS102A or SS105B TA205B Entrance Panels Door Release Transformer Handset Suite Station

21 PK601A 24 VDC Power Supply IL420 Section D Rev /2008 The PK601A is a 24 VDC power supply designed to power auxiliary signaling devices used in TekTone emergency call systems. The unit provides a filtered 24 VDC output rated at 1 amp. Although specifically designed for use with emergency call systems, the PK601A may also be used as a DC silent door opener adapter in TekTone apartment entrance systems. Easy installation Low-voltage operation Multiple applications Precision engineering S PK601A 24 VDC Power Supply Dimensions: Height: 5" (127 mm) Width: 2.375" (60 mm) Depth: 2.25" (57 mm) Construction: Quality electronic components mounted on a PC board encased in a rugged extruded aluminum housing Connections: Screw terminals Mounting: Surface Output voltage: 24 VDC Output current: 1 amp Power Requirements: 16 VAC, 30 VA The power supply shall be TekTone PK601A, or approved equal, and shall provide 24 VDC power to auxiliary signaling devices used in specified TekTone emergency call systems. The PK601A shall also be suitable for use as a DC silent door opener adapter in specified TekTone apartment entrance systems. The PK601A circuitry shall be housed in a rugged extruded aluminum case. Screw terminals shall be provided for installation wiring.

22 PK543A Apartment Intercom Amplifier for 5-, 4- & 3-Wire Remote Stations IL482 Rev /2006 PK543A The PK543A Apartment Intercom Amplifier is a selfcontained unit that does not require an external amplifier. The PK543A is designed for use with 3-, 4- or 5-wire apartment remote stations and provides amplification, control and power circuits needed to operate a complete apartment intercom system. Voice volume control and tone volume control are easily adjustable through the screwdriver opening on the front panel. Additional functions include multiple door entrance operation with the PK502B; AC, DC or Maglock configurations with three selectable delayed door timing modes; post office door lock release; steady or warble call tones; power LED; selectable door button hold timeout; and selectable talk before door interlock (available for 4-wire stations only). S The intercom amplifier shall be PK543A or approved equal, and shall provide the amplification, control and power circuits needed to operate the entire intercom system. The amplifier shall feature integrated circuit amplification, integrated circuit tone oscillator (supporting steady and warble tone modes). User access to the voice volume control and call tone volume control shall be provided for field adjustment. Unit shall also provide for AC, DC or Maglock (12 VDC/ 24 VDC) door release with three selectable delayed door timing modes and support for postal lock door access control. Steady and warble tone options shall be available to provide identification of call source from entrance panel or suite call button. Unit shall include power LED and selectable options to provide door button hold timeout and talk interlock (talk button must be pressed before door button is pressed available for 4-wire stations only). A specific function connector shall be provided to facilitate connection to devices that provide multiple entrance panel functionality. Low voltage wiring shall be used and plug-in type terminals shall be provided for installation wiring. Dimensions: Height: 5.5" (140 mm) Width: 3.125" (80 mm) Depth: 2" (51 mm) Construction: Amplification: Call Tone: Door Release: Controls: Connections: Power Required: 16 VAC, 10 VA Mounting: Surface mount AM or CM series IR Series SS Series Flame-retardant (UL 94V-0) plastic Integrated Circuit amplifier including amplifier with frequency response, adjusted for ideal voice quality. Integrated circuit oscillator with steady and warble modes AC, DC or Maglock (12 VDC/24 VDC) Voice Volume, Tone Volume and Dipswitches for selectable modes Polarized plug-in type Entrance Panels Remote Stations Transformers

23 PO101S Postal Door Release IL593 Rev. 5-03/2008 The PO101S Postal Door Release provides for postal lock installation and microswitch control of door release devices. It is constructed of a rugged aluminum panel with durable, flame retardant ABS plastic endcaps. The extrusion design provides sufficient depth to make the panel surface mountable with no additional housing required. A gasket is also attached to the rear surface to increase the station s resistance to weather exposure. S PO101S Postal door release shall be TekTone PO101S or approved equal. Postal door release panel shall be surface mountable and include a gasket to provide resistance to weather exposure. The postal door release shall be constructed of a rugged extruded aluminum panel with necessary mounting hardware and a microswitch to allow for the installation of a postal lock. Endcaps for the panel shall be molded of durable, flame retardant ABS plastic. The microswitch shall have wire leads to provide for easy connection. Dimensions: Height: 7.25" (184 mm) Width: 4.9" (125 mm) Depth: 1.5" (38 mm) Construction: Rugged extruded aluminum panel with durable, flame retardant ABS plastic endcaps Finish: Brushed aluminum Tek-ENTRY -or- Apartment Entry System Vandal-Resistant Entry System

24 TA205C Handset Intercom Suite Station IL081 Rev /2009 The TA205C Handset Intercom Suite Station is designed especially for intercom use. It features compact modern styling and advanced electronic design using dynamic speech elements. The TA205C includes an integral push button for door lock release, and a reliable hook cradle switch. The TA205C is molded of a high impact flame retardant ABS plastic and is suitable for a variety of applications. Clear, true voice reproduction Integral door lock release push button Easy to install and use Audible signal tone TA205C Handset intercom suite station shall be TekTone TA205C, or approved equal. The TA205C shall be molded of a highimpact flame retardant ABS plastic. Dynamic speech elements shall be used, and a push button shall be provided for door lock release. The suite station shall be mounted on a standard single gang electrical box and have screw terminals for wiring hook-up. S Dimensions: Height: 9.03" (229 mm) (not including cord) Width: 2.87" (73 mm) Depth: 2.84" (72 mm) Construction: High impact flame retardant ABS plastic Speech Elements: Dynamic with voice response Push Button: Replaceable with plated, self-wiping contacts Connections: Screw terminals Color: Mounting: White Standard single gang electrical box, installed vertically CM193 or AM193 PK205 SS102A or SS105B PO001 Entrance Panel Amplifier Transformer Electric Door Opener (optional)

25 Housings Reference Chart IL312 Rev /2007 NOTES: 1. For SF Series Emergency Switches, use single gang ring, or single gang ring and double gang box IH357/IH For LI Dome Light Series, use double gang ring (or double gang ring and box). 3. For AM and CM Series, see specification requirements. 4. For IR300 Series Nurse Call Stations, use Steel City #3GC and #H3BD or exact equivalent. 5. For IR150B Series, use Steel City #3GC and #H3BD. If space is limited, use ARC-CO #2GBD and #3GC. 6. For IR150SS Station, use OH600 flush housing mounted horizontally. 7. The last two digits of frame and housing model numbers indicate the number of gangs (i.e., panel capacity). Exceptions: IH101, IH102, OH600, OH601, IH400A. IH101 backbox (flush) IH102 ring (flush) IH400A housing (desk) Model # IR100B IR102C IR103E IR104E IR105E IR203E IR204E IR205E IR207B use standard 2-gang electrical box IR704BD OR500 Series OR600 Series use standard 1-gang electrical box SM201B use standard 1-gang SM201K/P electrical box Dimension and Finish Chart Housings, Frames, Desk Cabinets Flush Mount Housings Overall Wall Cutout Overall Wall Cutout Overall Model# Width Width Height Height Depth IH101 4" 4-1/4" 5-1/2" 5-3/4" 1-3/4" IH /4" 4-1/4" 6" 5-5/8" 1/2" OH /4" 4-1/2" 11-1/8" 10-5/8" 3-7/8" OH /8" 4-1/2" 17-1/8" 17-1/4" 3-1/2" OH /8" 8-1/2" 17-1/8" 17-1/4" 3-1/2" OH /8" 12-1/2" 17-1/8" 17-1/4" 3-1/2" OH /8" 16-1/2" 17-1/8" 17-1/4" 3-1/2" OH /8" 20-1/2" 17-1/8" 17-1/4" 3-1/2" OH /8" 4-1/2" 16-7/8" 16-1/4" 3-7/8" OH /8" 8-1/2" 16-7/8" 16-1/4" 3-7/8" OH /8" 12-1/2" 16-7/8" 16-1/4" 3-7/8" OH600 4" 4-1/4" 10-3/16" 10-3/8" 1-13/16" OH601 4" 4-1/4" 16-1/16" 16-1/4" 1-13/16" Frames Model # Width Wall Cutout OF /4" - OF /4" - OF /4" - OF /4" - OF /4" - Height: 19" (overall) Depth: 7/8" OF /4" 4-1/2" OF /4" 8-1/2" OF /4" 12-1/2" Height: 17-3/4" (overall) Cutout: 15-7/8" Depth: 2-1/2" Desk Cabinets Model # Width Depth *IH /2" 6" *IH /2" 6" *IH /2" 6" IH400A (white) 5" 7" * Cabinet Assembly Only. IH300 series Height = 17" Surface Mount Frames Model # Width Height Depth OF190S 4-1/4" 19-3/4" 1-1/2" OF191S 6-1/4" 19" 2-1/4" OF192S 10-1/4" 19" 2-1/4" OF193S 14-1/4" 19" 2-1/4" OF194S 18-1/4" 19" 2-1/4" OF195S 22-1/4" 19" 2-1/4" Surface Mount Housings Model # Width OH /8" OH /8" Height: 17-3/4" Depth: 3-5/8"