FCX-11AB5-3XX-XX 155Mbps BIDI SFP TRANSCEIVER(100Km)

Size: px

Start display at page:

Download "FCX-11AB5-3XX-XX 155Mbps BIDI SFP TRANSCEIVER(100Km)"

Felicia Lynch
6 years ago
Views:

1 FEATURES LC or SC receptacle optical interface compliant Single 3.3V power supply Hot-pluggable Uncooled 1490nm DFB laser transmitter Receiver loss of signal output AC/AC Coupling according to MSA Transmitter disable input DDM function implemented External calibration Serial ID module on MOD(0-2) International Class 1 laser safety certified RoHS complian APPLICATIONS SDH/STM-1,SONET/OC-3 Metropolitan area network STANDARD Compliant with Rev10.2 SFF-8472 Compliant with ITU-T G.957 STM-1 Compliant with SFP MSA(INF-8074i) Absolute Maximum Ratings Parameter Symbol Min. Max. Units Note Storage Temperature Ts Power Supply Voltage Vcc V Soldering Temperature seconds on leads only Recommended Operating Conditions Parameter Symbol Min. Typ. Max. Units Note Operating Supply Voltage Vcc V Operating Temperature Top 0 70 FCX-11AB5-3CX-XX FCX-11AB5-3TX-XX Data Rate 155 Mbps Power Supply Current(1) Icc ma - 1

2 Transmitter Specifications FCX-11AB5-3XX-XX Parameter Symbol Min. Typ. Max. Units Optical Optical Transmit Power Po -2 3 dbm Optical Center Wavelength λc nm Output Spectrum Width Δλ 1 nm SMSR 30 db Extinction Ratio ER db Output Eye Compliance with ITU-T G.957 Optical Rise Time tr ns Optical Fall Time tf ns Jitter(2) TJ 0.1 Uip-p Relative Intensity Noise(3) RIN -116 db/hz Electrical Data Input Current Low IIL -350 ua Data Input Current High 350 A Differential Input Voltage VIH -VIL mv TX Disable Input Voltage-Low TDL V TX Disable Input Voltage-High TDH VCC V TX Disable Assert Time TDAT 10 us TX Disable Deassert Time TDDT 1 ms TX Fault Output Voltage-Low TFL V TX Fault Output Voltage-High TFH 2.0 VCC+0.3 V Receiver Specifications Parameter Symbol Min. Typ. Max. Units Optical Sensitivity(4) Sen -37 dbm Overload Pin -3 dbm Signal Detect -- Asserted Pa -38 dbm Signal Detect -- Deasserted Pd -45 dbm Signal Detect Hysteresis(5) Phys 1 5 db Wavelength of Operation λ nm Electrical Differential Output Voltage VOH VOL mv Output LOS Voltage Low VOH mv Output LOS Voltage High VOL VCC+300 mv Note1: The supply current includes SFP module s supply current and test board working current. Note2: For the jitter measurements, the device was driven with SONET OC-3 data pattern with PRBS payload. - 2

3 Note3: RIN is the laser noise, integrated over a specified bandwidth, measured relative to average optical power with 12dB return loss. Note4: Measured with a PRBS test EX=10dB, BER< Note5: The LOS Hysteresis to minimize chatter on the output line. In principle, Hysteresis alone does not guarantee chatter-free operation.pin ASSIGNMENT Pin Name Function/Description 1 VeeT Transmitter Ground 2 TX Fault Transmitter Fault Indication 3 TX Disable Transmitter Disable-Module disables on high or open 4 MOD-DEF2 Module Definition 2-Two wire serial ID interface 5 MOD-DEF1 Module Definition 1-Two wire serial ID interface 6 MOD-DEF0 Module Definition 0-Two wire serial ID interface 7 Rate Select Not Connected 8 LOS Loss of Signal 9 VeeR Receiver Ground 10 VeeR Receiver Ground 11 Veer Receiver Ground 12 RD- Inverse Received Data out 13 RD+ Received Data out 14 VeeR Receiver Ground 15 VccR Receiver Power V±5% 16 VccT Transmitter Power V±5% - 3

4 17 VeeT Transmitter Ground 18 TD+ Transmitter Data In 19 TD- Inverse Transmitter Data In 20 VeeT Transmitter Ground Note1: TX Fault is open collector/drain output which should be pulled up externally with a 4.7K- 10KΩresistor on the host board to supply <VccT+0.3V or VccR+0.3V. When high, this output indicates a laser fault of some kind. Low indicates normal operation. In the low state, the output will be pulled to <0.8V. Note2: TX Disable input is used to shut down the laser output per the state table below. It is pulled up within the module with a K resistor. Low (0 0.8V): Transmitter on Between (0.8V and 2V): Undefined High (2.0 VccT): Transmitter Disabled Open : Transmitter Disabled Note3: Mod-Def 0, 1, 2. These are the module definition pins. They should be pulled up with a K resistor on the host board to supply less than VccT+0.3V or VccR+0.3V. Mod-Def 0 is grounded by the module to indicate that the module is present. Mod-Def 1 is clock line of two wire serial interface for optional serial ID. Mod-Def 2 is data line of two wire serial interface for optional serial ID. Note4: LOS (Loss of signal) is an open collector/drain output which should be pulled up externally with a K resistor on the host board to supply <VccT+0.3V or VccR+0.3V. When high, this output indicates the received optical power is below the worst case receiver sensitivity (as defined by the standard in use). Low indicates normal operation. In the low state, the output will be pulled to <0.8V. Block Diagram SD RD+ RD- Limiting Amplifier Preamplifi -er Photo Detector Optical Signal Input MOD_DEF(2) MOD_DEF(1) MOD_DEF(0) DDMI& EEPROM RX_Power WDM TD- TD+ Laser Bia TX_Power LD Driving Circuit and Control Circuit Laser Diode Optical Signal Output TX_Disable TX_Fault - 4

5 Application Circuit Digital Diagnostic Memory map - 5

6 EEPROM Serial ID Memory Contents FCX-11AB5-3XX-XX Accessing Serial ID Memory uses the 2 wire address X (A0). Memory Contents of Serial ID are shown in the Table 1. Table 1: Serial ID Memory Contents Data Size Address (Bytes) Name of Field Contents(Hex) Description BASE ID FIELDS 0 1 Identifier 03 SFP 1 1 Ext.Identifier 04 SFP function is defined by serial ID only 2 1 Connector 07 LC Connector Transceiver Transceiver Codes 11 1 Encoding 03 NRZ 12 1 BR,Nominal Mbit/s 13 1 Reserved Length(9um)km 15 1 Length(9um) 16 1 Length(50um) 17 1 Length(62.5um) 18 1 Length(Copper) 00 Not compliant 19 1 Reserved Vendor name 42 4F 54 4F 4E Reserved Vendor OUI Transceiver transmit distance BOTONE (ASCII) Vendor PN Transceiver part number Vendor rev Wavelength 05 1E/06 0E 62 1 Reserved CC_BASE Options 00 1A 66 1 BR,max BR,min Vendor SN Transceiver wavelength example 1310/1550 Check Sum Check code for Base ID Fields (Variable) EXTENDED ID FIELDS TX_DISABLE, TX_FAULT and Loss of Signal implemented. Serial Number of transceiver (ASCII). For example

7 Date code Manufactory date code. For example Digital diagnostic monitoring implemented, 92 1 Diagnostic externally calibrated / internally calibrated is 58 Monitoring Type implemented, RX measurement type is Average Power Optional Alarm/Warning flags implemented for all Enhanced monitored quantities, Optional Soft TX_FAULT B0 Options monitoring implemented, Optional Soft RX_LOS monitoring implemented SFF_8472 Includes functionality described in Rev Compliance SFF CC_EXT Check Sum (Variable) Check sum for Extended ID Field. VENDOR SPECIFIC ID FIELDS Vendor Specific Read only Depends on customer information Reserved Read only Filled by zero Diagnostic Monitor Functions Diagnostic Monitor Functions interface uses the 2 wire address X (A2). Memory contents of Diagnostic Monitor Functions are shown in Table 2 Table 2: Memory contents of Diagnostic Monitor Function Data Address Field Size (bytes) Name Contents and Description Alarm and Warning Thresholds 9 2 Temperature High Alarm On select Temperature Low Alarm On select Temperature High Warning On select Temperature Low Warning On select Vcc High Alarm Set to 3.6 V Vcc Low Alarm Set to 3.0 V Vcc High Warning Set to 3.5 V Vcc Low Warning Set to 3.1 V Bias High Alarm 2 Ibias(25 o C ) Bias Low Alarm 25% IBias (25 o C ) Bias High Warning 2 IBias(25 o C ) Bias Low Warning 50% IBias(25 o C ) TX Power High Alarm Manufacture measurement plus 2dB TX Power Low Alarm Manufacture measurement minus 2dB TX Power High Warning Manufacture measurement plus 1dB TX Power Low Warning Manufacture measurement minus 1 db - 7

8 RX Power High Alarm Maximum input optical power RX Power Low Alarm Minimum input optical power RX Power High Warning Maximum input power minus 3dB RX Power Low Warning Manufacture measurement plus 3dB Reserved Calibration Constants RX Power Calibration Data RX Power Calibration Data3 Single precision floating-point numbers (various RX Power Calibration Data2 values at each device) RX Power Calibration Data RX Power Calibration Data Bias Calibration Data (fixed) Bias Calibration Data (fixed) TX Power Calibration Data (fixed) TX Power Calibration Data (fixed) Temperature Calibration Data (fixed) Temperature Calibration Data (fixed) Vcc Calibration Data (fixed) Vcc Calibration Data (fixed) Reserved (fixed) 95 1 Check Sum Checksum of bytes 0-94 Real Time Diagnostic Monitor Interface Measured Temperature Yield to a 16-bit A/D value (see Table 2.1) Measured Vcc Yield a 16-bit A/D value (see Table 2.1) Measured Bias Yield a 16-bit A/D value (see Table 2.1) Measured TX Power Yield a 16-bit A/D value (see Table 2.1) Measured RX Power Yield a 16-bit A/D value (see Table 2.1) Reserved Logic Status See Table AD Conversion Updates See Table Alarm and Warning Flags See Table 2.3 Vendor Specific Vendor Specific Don t Access User writable EEPROM Vendor Specific Don t Access The measured values located at bytes (in the 2 wire address 0xA2) are raw A/D values (16-bit integers) of transceiver temperature, supply voltage, laser bias current, laser optical output power and received power. All the measured values are Externally Calibrated, and then it is necessary to convert raw A/D values to real world units by the manner as shown in Table

9 Table 2.1: Real Time Diagnostic Monitor Values FCX-11AB5-3XX-XX Byte Name Description 96 Temperature MSB 97 Temperature LSB 98 Vcc MSB 99 VCC LSB 100 Laser Bias MSB 101 Laser Bias MSB 102 Tx Power MSB 103 TX Power LSB 104 Rx Power MSB 105 RX Power LSB Internally measured transceiver temperature. Comply with External Calibration of SFF Internally measured supply voltage. Comply with External Calibration of SFF Measured Laser bias current. Comply with External Calibration of SFF Measured Tx power. Comply with External Calibration of SFF Measured Tx power. Comply with External Calibration of SFF This transceiver implements two optional status bytes, Logic States at byte 110(0xA2) and A/D Updated at byte 111(0xA2) as shown in Table 3.2. A/D Updated status bits allow the user to verify if an update from the analog-digital conversion has occurred of the measured values, temperature, Vcc, laser bias, Tx power and Rx power. The user writes the byte to 0x00. Once a conversion is completed for a given value, its bit will change to 1. Table 2.2:Logic Status and AD Conversion Updates Byte Bit Name Description Tx Disable State Optional digital State of the Tx Disable input pin Soft Tx Disable Control Not supported (set to 0) Reserved Set to Rx Rate Select State Not supported (set to 1) Soft Rate Select Control Not supported (set to 0) Tx Fault Optional digital state of the Tx Fault output pin LOS Optional digital state of the LOS output pin Power on Logic Bit will be 0 when the analog monitoring is active Temp A/D Valid Indicates A/D value in Bytes 96/97 is valid Vcc A/D Valid Indicates A/D value in Bytes 98/99 is valid Laser Bias A/D Valid Indicates A/D value in Bytes 100/101 is valid Tx Power A/D Valid Indicates A/D value in Bytes 102/103 is valid Rx Power A/D Valid Indicates A/D value in Bytes 104/105 is valid Reserved Set to Reserved Set to Reserved Set to 0. Each of the measured values has a corresponding high alarm, low alarm, high warning and low warning threshold level at location 00-39(x0A2) written as the data format of a corresponding valued shown in Table 2.3.Alarm and warning flags at bytes (0xA2) are defined as follows. [1] Alarm flags indicate conditions likely to result (or have resulted) in link failure and cause for immediate - 9

10 action. FCX-11AB5-3XX-XX [2] Warning flags indicate conditions outside the guaranteed operating specification of transceiver but not necessarily causes of immediate link failures. Table 2.3:Alarm and Warning Flags Byte Bit(s) Name Description Temperature High Alarm Set when temperature monitor value exceeds high alarm Temperature Low Alarm Set when temperature monitor value exceeds low alarm Vcc High Alarm Set when Vcc monitor value exceeds high alarm Vcc Low Alarm Set when Vcc monitor value exceeds Low alarm Laser Bias High Alarm Set when laser bias monitor value exceeds high alarm Laser Bias Low Alarm Set when laser bias monitor value exceeds low alarm Tx Power High Alarm Set when Tx power monitor value exceeds high alarm level Tx Power Low Alarm Set when Tx power monitor value exceeds low alarm Rx Power High Alarm Set when Rx power monitor value exceeds high alarm level Rx Power Low Alarm Set when Rx power monitor value exceeds low alarm level Reserved All bits set to Reserved All bits set to Reserved All bits set to Temperature High Set when temperature monitor value exceeds high warning warning Temperature Low Set when temperature monitor value exceeds low warning warning Vcc High warning Set when Vcc monitor value exceeds high warning Vcc Low warning Set when Vcc monitor value exceeds Low warning Laser Bias High warning Set when laser bias monitor value exceeds high warning Laser Bias Low warning Set when laser bias monitor value exceeds low warning Tx Power High warning Set when Tx power monitor value exceeds high warning level Tx Power Low warning Set when Tx power monitor value exceeds low warning Rx Power High warning Set when Rx power monitor value exceeds high warning level Rx Power Low warning Set when Rx power monitor value exceeds low warning level Reserved All bits set to

11 Reserved All bits set to Reserved All bits set to 0. PACKAGE DIAGRAM (Units in mm) 1) FCL-11AB5-3XX-XX(Receptacle:LC) 2) FCS-11AB5-3XX-XX(Receptacle:SC) - 11

12 ORDER INFORMATION FCX-11AB5-3XX-XX D=DDM SFP,T=Without DDM Operating temperature:c=0~70 C,T=-40~85 C Receptacle:S=SC,L=LC - 12

1.25G SFP transceiver with DDM function. RTXM191-xxx (DDM) Features

1.25G SFP transceiver with DDM function RTXM191-xxx (DDM) Features Up to 1.25Gbps data rate Duplex LC receptacle optical interface compliant Single +3.3V power supply DDM function implemented External