CMP-2401B/CMP-2402B. Fire Alarm Control Panel. Installation, Maintenance and Operating Instruction Manual

Save this PDF as:
 WORD  PNG  TXT  JPG

Size: px
Start display at page:

Download "CMP-2401B/CMP-2402B. Fire Alarm Control Panel. Installation, Maintenance and Operating Instruction Manual"

Transcription

1 10 Whitmore Road Woodbridge, Ontario L4L 7Z4 Phone (905) FAX (905) CMP-2401B/CMP-2402B Fire Alarm Control Panel Installation, Maintenance and Operating Instruction Manual P/N 50907:A1 ECN A Document # /03/02 Rev Fire Lite

2 Fire Alarm System Limitations An automatic fire alarm system typically made up of smoke detectors, heat detectors, manual pull stations, audible warning devices, and a fire alarm control with remote notification capability can provide early warning of a developing fire. Such a system, however, does not assure protection against property damage or loss of life resulting from a fire. The Manufacturer recommends that smoke and/or heat detectors be located throughout a protected premise following the recommendations of the current edition of the National Fire Protection Association Standard 72 (NFPA 72), manufacturer's recommendations, State and local codes, and the recommendations contained in the Guide for Proper Use of System Smoke Detectors, which is made available at no charge to all installing dealers. A study by the Federal Emergency Management Agency (an agency of the United States government) indicated that smoke detectors may not go off in as many as 35% of all fires. While fire alarm systems are designed to provide early warning against fire, they do not guarantee warning or protection against fire. A fire alarm system may not provide timely or adequate warning, or simply may not function, for a variety of reasons: Smoke detectors may not sense fire where smoke cannot reach the detectors such as in chimneys, in or behind walls, on roofs, or on the other side of closed doors. Smoke detectors also may not sense a fire on another level or floor of a building. A second-floor detector, for example, may not sense a first-floor or basement fire. Particles of combustion or "smoke" from a developing fire may not reach the sensing chambers of smoke detectors because: Barriers such as closed or partially closed doors, walls, or chimneys may inhibit particle or smoke flow. Smoke particles may become "cold," stratify, and not reach the ceiling or upper walls where detectors are located. Smoke particles may be blown away from detectors by air outlets. Smoke particles may be drawn into air returns before reaching the detector. The amount of "smoke" present may be insufficient to alarm smoke detectors. Smoke detectors are designed to alarm at various levels of smoke density. If such density levels are not created by a developing fire at the location of detectors, the detectors will not go into alarm. Smoke detectors, even when working properly, have sensing limitations. Detectors that have photoelectronic sensing chambers tend to detect smoldering fires better than flaming fires, which have little visible smoke. Detectors that have ionizing-type sensing chambers tend to detect fast-flaming fires better than smoldering fires. Because fires develop in different ways and are often unpredictable in their growth, neither type of detector is necessarily best and a given type of detector may not provide adequate warning of a fire. Smoke detectors cannot be expected to provide adequate warning of fires caused by arson, children playing with matches (especially in bedrooms), smoking in bed, and violent explosions (caused by escaping gas, improper storage of flammable materials, etc.). While a fire alarm system may lower insurance rates, it is not a substitute for fire insurance! Heat detectors do not sense particles of combustion and alarm only when heat on their sensors increases at a predetermined rate or reaches a predetermined level. Rate-of-rise heat detectors may be subject to reduced sensitivity over time. For this reason, the rate-of-rise feature of each detector should be tested at least once per year by a qualified fire protection specialist. Heat detectors are designed to protect property, not life. IMPORTANT! Smoke detectors must be installed in the same room as the control panel and in rooms used by the system for the connection of alarm transmission wiring, communications, signaling, and/or power. If detectors are not so located, a developing fire may damage the alarm system, crippling its ability to report a fire. Audible warning devices such as bells may not alert people if these devices are located on the other side of closed or partly open doors or are located on another floor of a building. Any warning device may fail to alert people with a disability or those who have recently consumed drugs, alcohol or medication. Please note that: Strobes can, under certain circumstances, cause seizures in people with conditions such as epilepsy. Studies have shown that certain people, even when they hear a fire alarm signal, do not respond or comprehend the meaning of the signal. It is the property owner's responsibility to conduct fire drills and other training exercise to make people aware of fire alarm signals and instruct them on the proper reaction to alarm signals. In rare instances, the sounding of a warning device can cause temporary or permanent hearing loss. A fire alarm system will not operate without any electrical power. If AC power fails, the system will operate from standby batteries only for a specified time and only if the batteries have been properly maintained and replaced regularly. Equipment used in the system may not be technically compatible with the control. It is essential to use only equipment listed for service with your control panel. Telephone lines needed to transmit alarm signals from a premise to a central monitoring station may be out of service or temporarily disabled. For added protection against telephone line failure, backup radio transmission systems are recommended. The most common cause of fire alarm malfunction is inadequate maintenance. To keep the entire fire alarm system in excellent working order, ongoing maintenance is required per the manufacturer's recommendations, and UL and NFPA standards. At a minimum, the requirements of Chapter 7 of NFPA 72 shall be followed. Environments with large amounts of dust, dirt or high air velocity require more frequent maintenance. A maintenance agreement should be arranged through the local manufacturer's representative. Maintenance should be scheduled monthly or as required by National and/ or local fire codes and should be performed by authorized professional fire alarm installers only. Adequate written records of all inspections should be kept. LimWarLg.p65 01/10/2000

3 Installation Precautions WARNING - Several different sources of power can be connected to the fire alarm control panel. Disconnect all sources of power before servicing. Control unit and associated equipment may be damaged by removing and/or inserting cards, modules, or interconnecting cables while the unit is energized. Do not attempt to install, service, or operate this unit until this manual is read and understood. CAUTION - System Reacceptance Test after Software Changes. To ensure proper system operation, this product must be tested in accordance with NFPA 72 Chapter 7 after any programming operation or change in site-specific software. Reacceptance testing is required after any change, addition or deletion of system components, or after any modification, repair or adjustment to system hardware or wiring. All components, circuits, system operations, or software functions known to be affected by a change must be 100% tested. In addition, to ensure that other operations are not inadvertently affected, at least 10% of initiating devices that are not directly affected by the change, up to a maximum of 50 devices, must also be tested and proper system operation verified. This system meets NFPA requirements for operation at 0-49 C/ F and at a relative humidity of 85% RH (noncondensing) at 30 C/86 F. However, the useful life of the system's standby batteries and the electronic components may be adversely affected by extreme temperature ranges and humidity. Therefore, it is recommended that this system and all peripherals be installed in an environment with a nominal room temperature of C/60-80 F. Verify that wire sizes are adequate for all initiating and indicating device loops. Most devices cannot tolerate more than a 10% I.R. drop from the specified device voltage. Adherence to the following will aid in problem-free installation with long-term reliability: Like all solid state electronic devices, this system may operate erratically or can be damaged when subjected to lightning-induced transients. Although no system is completely immune from lightning transients and interferences, proper grounding will reduce susceptibility. Overhead or outside aerial wiring is not recommended, due to an increased susceptibility to nearby lightning strikes. Consult with the Technical Services Department if any problems are anticipated or encountered. Disconnect AC power and batteries prior to removing or inserting circuit boards. Failure to do so can damage circuits. Remove all electronic assemblies prior to any drilling, filing, reaming, or punching of the enclosure. When possible, make all cable entries from the sides or rear. Before making modifications, verify that they will not interfere with battery, transformer, and printed circuit board location. Do not tighten screw terminals more than 9 in-lbs. Over-tightening may damage threads, resulting in reduced terminal contact pressure and difficulty with screw terminal removal. Though designed to last many years, system components can fail at any time. This system contains static-sensitive components. Always ground yourself with a proper wrist strap before handling any circuits so that static charges are removed from the body. Use static-suppressive packaging to protect electronic assemblies removed from the unit. Follow the instructions in the installation, operating, and programming manuals. These instructions must be followed to avoid damage to the control panel and associated equipment. FACP operation and reliability depend upon proper installation by authorized personnel. FCC Warning WARNING: This equipment generates, uses, and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual, may cause interference to radio communications. It has been tested and found to comply with the limits for class A computing device pursuant to Subpart B of Part 15 of FCC Rules, which is designed to provide reasonable protection against such interference when operated in a commercial environment. Operation of this equipment in a residential area is likely to cause interference, in which case the user will be required to correct the interference at his own expense. Canadian Requirements This digital apparatus does not exceed the Class A limits for radiation noise emissions from digital apparatus set out in the Radio Interference Regulations of the Canadian Department of Communications. Le present appareil numerique n'emet pas de bruits radioelectriques depassant les limites applicables aux appareils numeriques de la classe A prescrites dans le Reglement sur le brouillage radioelectrique edicte par le ministere des Communications du Canada. LimWarLg.p65 01/10/2000

4 Notes 4 Document #50907 Rev.A1 12/03/02 P/N 50907:A1

5 Table of Contents CHAPTER 1: Product Description : Product Features...9 FIGURE 1-1: CMP-2401B/CMP-2402B : Specifications : Controls, Indicators and Operation : Front Panel Slide Switches...12 FIGURE 1-2: CMP-2401B/CMP-2402B Control Switches : LED Indicators...13 FIGURE 1-3: LED Indicators (CMP-2402B Illustrated) : Local Sounder : Normal Standby Operation : Alarm Condition : Trouble Condition : Circuits : Components : Optional Modules and Accessories...16 CHAPTER 2: Installation : Mounting Options...17 FIGURE 2-1: CMP-2401B/CMP-2402B Mounting : Backbox Mounting...17 FIGURE 2-2: Cabinet Dimensions and Knockout Locations...18 FIGURE 2-3: FACP Backbox : Operating Power...20 FIGURE 2-4: Operating Power Connections : Input Circuits...21 FIGURE 2-5: CMP-2402B Style B Initiating Device Circuit Connections : Output Circuits...22 FIGURE 2-6: Auxiliary Power Connection...22 FIGURE 2-7: Notification Appliance Circuit Connections...22 FIGURE 2-8: Relay Terminals : UL Power-limited Wiring Requirements...23 FIGURE 2-9: Typical Wiring Diagram for UL Power-limited Requirements : Installation of Optional Module : 4XTMF Transmitter Module...24 FIGURE 2-10: 4XTMF Module Connections : RTB - Remote Trouble Buzzer...25 FIGURE 2-11: RTB Remote Trouble Buzzer Connection...25 CHAPTER 3: Programming Options : Earth Ground Fault Detection...26 FIGURE 3-1: Ground Fault Detection Circuit : Optional 4XTMF Transmitter Module Placement Supervision...26 FIGURE 3-2: 4XTMF Module Placement Supervision...26 CHAPTER 4: Periodic Testing and Maintenance...27 CHAPTER 5: Battery Calculations...28 TABLE 5-1: Battery Calculations : The Main Power Supply...29 TABLE 5-2: Load in Standby...29 TABLE 5-3: Load in Alarm...30 Document Rev. A1 12/03/02 P/N: 50907:A1 5

6 Notes 6 Document #50907 Rev.A1 12/03/02 P/N 50907:A1

7 This control panel has been designed to comply with standards set forth by the following regulatory agencies: Underwriters Laboratories Standard UL 864 NFPA 72 National Fire Alarm Code CAN/ULC - S527M Standard for Control Units for Fire Alarm Systems Before proceeding, the installer should be familiar with the following documents. NFPA Standards This Fire Alarm Control Panel complies with the following NFPA Standards: NFPA 72 National Fire Alarm Code for Local Fire Alarm Systems and Remote Station Fire Alarm Systems (requires an optional Remote Station Output Module). Underwriters Laboratories Canada Documents: CAN/ULC - S524M Standard for Installation of Fire Alarm Systems CAN/ULC - S527-M87 Standard for Control Units for Fire Alarm Systems Other: Applicable Local and State Building Codes C22.1 Canadian Electrical Code, Part I C22.2 No. 0, General Requirements - Canadian Electrical Code, Part II C22.2 No. 0.4, Bonding and Grounding of Electrical Equipment (Protective Grounding) - Canadian C282, Emergency Electrical Power Supply for Buildings - Canadian Requirements of the Local Authority Having Jurisdiction (LAHJ) Fire Lite Documents Fire Lite Device Compatibility Document Document #15384 Document #50907 Rev. A1 12/03/02 P/N 50907:A1 7

8 CMP-2401B/CMP-2402B Main Circuit Board Connections to Remote Trouble Buzzer CMP-2402B Only GND AC TBL BUZ +24V ALARM REG RES NC C NO TROUBLE NC C NO SIGNAL OUTPUT + - INITIAT ZONE INITIAT ZONE TB1 TB2 GND AC TBL BUZ +24V REG RES NC ALARM C NO TROUBLE NC C NO SIGNAL OUTPUT + - INITIAT ZONE INITIAT ZONE TB1 TB2 SW1 SYSTEM RESET System Reset SW2 SIG SILENCE ZONE 1 Signal Silence Zone 1 Transformer J5 CUT IF 4X OPTION BOARD IS PRESENT SW3 SW4 SIG SILENCE ZONE 2 TBL SILENCE Signal Silence Zone 2 (CMP-2402B Only) Trouble Silence R14 NEUTRAL F2 J4 CUT TO DISABLE EARTH FAULT R72 Cut if Option Board is Present R14 F2 AC Power Fuse 2 AMP 3AG Slow Blow EARTH HOT TB3 J3 BATTERY J1 J4 Cut to Disable Earth FAult R72 NEUTRAL EARTH J3 Battery (7.0 AH, 12 VDC) Option Module Connectors 2402LAYO.CDR HOT TB3 J1 8 Document #50907 Rev.A1 12/03/02 P/N 50907:A1

9 Product Description CHAPTER 1 Product Description The CMP-2401B is a one zone FACP (Fire Alarm Control Panel) and the CMP-2402B is a two zone FACP. This manual will use the term FACP to refer to both the CMP-2401B and CMP-2402B where features are identical. These control panels provide reliable fire signaling protection for small to medium sized commercial, industrial and institutional buildings. The FACPs use conventional input devices such as two-wire smoke detectors, four-wire smoke detectors, pull stations, waterflow devices and other normally-open contact devices. Outputs include one NAC (Notification Appliance Circuit) and 24 volt resettable power. The FACP also supervises all wiring, AC voltage and battery level. Activation of a compatible smoke detector or any normally open fire alarm initiating device will activate audible and visual signaling devices, illuminate an indicating LED and sound the piezo at the FACP, activate the FACP alarm relay and operate an optional module used to notify a remote station or initiate a supplementary control function. 1.1 Product Features Style B (Class B) Initiating Device Circuit (IDC) CMP-2401B - one IDC CMP-2402B - two IDCs One NFPA Style Y (Class B) Notification Appliance Circuit (NAC) Form-C Alarm Relay Form-C Trouble Relay Control switches Reset Trouble Silence Signal Silence - Zone One Signal Silence - Zone Two (CMP-2402B only) LED Indicators AC Power Zone Alarm and Trouble Bell Trouble Option Module Trouble System Trouble Zone Silence Ground Fault Battery Trouble Piezo Sounder for alarm and trouble signal Dress Panel coverplate 24 volt operation Small backbox size Low AC voltage sense Silence Inhibit Notification Appliance Circuit Automatic Battery Float Charger Battery Deep Discharge Protection Optional Remote Trouble Buzzer Document #50907 Rev. A1 12/03/02 P/N 50907:A1 9

10 Product Features FIGURE 1-1:CMP-2401B/CMP-2402B +24 Volt Resettable Power Trouble Relay Input Zones (2 on CMP-2402B only) Remote Trouble Buzzer Alarm Relay Notification Appliance Circuit Cut if 4X Option Module is Installed Transformer GND AC TBL BUZ +24V REG RES ALARM TROUBLE SIGNAL INITIAT INITIAT OUTPUT ZONE 1 ZONE 2 NC C NO NC C NO System Reset * TB1 TB2 SW1 SW2 SW3 SYSTEM RESET SIG SILENCE ZONE 1 SIG SILENCE ZONE 2 Signal Silence Zone 1* Signal Silence Zone 2 * (CMP- 2402B) J5 CAUTION! HIGH VOLTAGE F2 R14 CUT IF 4X OPTION BOARD IS PRESENT J4 SW4 CUT TO DISABLE EARTH FAULT TBL SILENCE Trouble Silence * Cut to Disable Earth Fault NEUTRAL EARTH HOT R72 4X Option Module Connectors TB3 J3 BATTERY J1 2401INBX.CDR Holds up to two 7 AH Batteries * Note that all switches are illustrated in the normal position. 10 Document #50907 Rev.A1 12/03/02 P/N 50907:A1

11 Specifications 1.2 Specifications AC Power - TB3 120 VAC, 60 Hz, 0.5 amps Fuse F2-2 Amp, 3AG Slow Blow Wire size: minimum #14 AWG (2.0 mm 2 ) with 600V insulation Battery (lead acid only) - J3 Maximum Charging Circuit: Normal Flat Charge amp Maximum Charger Capacity: 7.0 Amp Hour battery which can be housed in the FACP cabinet Battery Deep Discharge Protection: In order to protect the battery, the deep discharge circuit disconnects the battery from the FACP when the battery voltage drops below 15 VDC. The FACP will restart and the battery will begin recharging only after primary AC power is restored. Initiating Device Circuit(s) - TB2 Zone 1 - TB2 Terminals Initiating Zone 1 (-) & (+) Zone 2 - TB2 Terminals Initiating Zone 2 (-) & (+) (CMP-2402B only) Power-limited circuitry Operation: NFPA Style B (Class B) Normal Operating Voltage: Nominal 24 VDC, ripple 2.0 V P-P Alarm Current: 20 ma minimum Short Circuit Current: 40 ma maximum Maximum Loop Resistance: 100 ohms per side (200 ohms total zone resistance) End-of-Line Resistor: 3.9K ohm, ½ watt Detector Loop Current is sufficient to ensure operation of two alarmed detectors per zone Standby Current: 9 ma (includes ELR and 3 ma maximum detector current) Smoke Detector Identifier A Refer to Fire Lite Device Compatibility Document for listed compatible devices Notification Appliance Circuit - TB2, Terminals Signal Output (-) and Signal Output (+) Operation: NFPA Style Y (Class B) Power-limited circuitry Normal Operating Voltage: Nominal 24 VDC Current Limit: via PTC Maximum signaling current: 1.25 amps End-of-Line Resistor: 3.9K ohm, ½ watt Refer to Fire Lite Device Compatibility Document for listed compatible devices Two Form-C Relays - Terminals Alarm (NC, C, NO) and Trouble (NC, C, NO) Relay contact ratings: VDC (resistive), VAC (resistive) Resettable Power - TB1, Terminals Ground and +24V Resettable Operating Voltage: Nominal 24 VDC Up to 85 ma is available for powering 4-wire smoke detectors Power-limited circuitry Refer to Fire Lite Device Compatibility Document for compatible listed devices Document #50907 Rev. A1 12/03/02 P/N 50907:A1 11

12 Controls, Indicators and Operation 1.3 Controls, Indicators and Operation Front Panel Slide Switches FIGURE 1-2:CMP-2401B/CMP-2402B Control Switches SIGNAL INITIAT INITIAT OUTPUT ZONE 1 ZONE TB2 SW1 SYSTEM RESET System Reset SW2 SIG SILENCE ZONE 1 Signal Silence Zone 1 SW3 SIG SILENCE ZONE 2 Signal Silence Zone 2 (CMP-2402B only) CUT IF 4X OPTION BOARD IS PRESENT SW4 TBL SILENCE Trouble Silence R SWTC.CDR All switches are illustrated in their normal position. The function of each switch is listed below. System Reset The function of this nonlatching switch is: 1. to reset the FACP and the smoke detectors provided the alarm condition has been cleared and 60 seconds has elapsed since the first alarm 2. LED test Signal Silence - Zone 1 Placing the switch in the Silence position will silence the Notification Appliance Circuit if 60 seconds has elapsed since the first alarm. A trouble condition is indicated while the switch is in the Silence position. If an alarm occurs on the silenced zone, the alarm LED will indicate the alarm condition and the alarm relay will transfer. Signal Silence - Zone 2 (CMP-2402B only) Placing the switch in the Silence position will silence the Notification Appliance Circuit if 60 seconds has elapsed since the first alarm. A trouble condition is indicated while the switch is in the Silence position. If an alarm occurs on the silenced zone, the alarm LED will indicate the alarm condition and the alarm relay will transfer. Trouble Silence This latching, two-position switch, will silence the piezo sounder. The trouble LED will continue to indicate a trouble condition. An intermittent tone will sound when the trouble is cleared to indicate that this switch should be returned to its normal position. 12 Document #50907 Rev.A1 12/03/02 P/N 50907:A1

13 Controls, Indicators and Operation LED Indicators FIGURE 1-3:LED Indicators (CMP-2402B Illustrated) 2401DISP.CDR The LED indicators for the CMP-2401B/CMP-2402B are labeled in English and French. The purpose of each indicator is listed below: AC Power (Alimentation) - green LED The green LED is on when the FACP is operating from normal AC power. The LED turns off to indicate a below normal AC voltage (brownout) or complete loss of AC power. The System Trouble LED will also turn on. Option Trouble (Trouble Option) - yellow LED This yellow LED turns on to indicate the removal of the optional supervised 4XTMF Transmitter Module or a trouble with the module. Zone 1 Alarm (Alarme Zone 1) - red LED This red LED turns on to indicate an alarm condition, even if the Zone Silence switch is in the Silence position. Zone 2 Alarm (Alarme Zone 2) - red LED (CMP-2402B only) This red LED turns on to indicate an alarm condition, even if the Zone Silence switch is in the Silence position. Zone 1 Trouble (Trouble Zone 1) - yellow LED This yellow LED turns on to indicate a trouble condition, such as an open in the field wiring, on the IDC (Initiating Device Circuit) zone 1. Zone 2 Trouble (Trouble Zone 2) - yellow LED (CMP-2402B only) This yellow LED turns on to indicate a trouble condition, such as an open in the field wiring on the IDC (Initiating Device Circuit) zone 2. Zone Silence (M.S. Silence Zone) - yellow LED This yellow LED turns on to indicate that the Notification Appliance Circuit has been silenced. Bell Trouble (Trouble Cloche) - yellow LED This yellow LED turns on to indicate a trouble condition, such as an open or short in the field wiring, on the Notification Appliance Circuit. Battery Trouble (Trouble Piles) - yellow LED This yellow LED turns on to indicate a low battery/no battery condition or battery charger fault. Document #50907 Rev. A1 12/03/02 P/N 50907:A1 13

14 Controls, Indicators and Operation System Trouble (Trouble Systeme) - yellow LED This yellow LED turns on for all faults or abnormal operating conditions. Ground Fault (Faute M.A.L.T.) - yellow LED This yellow LED turns on to indicate a ground fault condition (low impedance to ground) on any field wiring or battery connections Local Sounder A piezo sounder provides distinct signals for alarm and trouble conditions: Alarm - steady Trouble - pulse Normal Standby Operation Normal standby operation indicates that there are no alarms or trouble conditions present on the FACP and that the IDC zone(s) have not been Silenced. In Normal Operation: All switches must be in their normal positions. Refer to Figure 1-1, CMP-2401B/CMP-2402B, on page 10. The green AC power LED is on steady The red alarm LED(s) are off All yellow trouble LEDs are off Alarm Condition Alarm condition indicates that an IDC (input) zone has detected an alarm (active smoke detector, pull station activation, etc.). In Alarm Operation: The zone alarm LED will turn on The notification appliances are activated The optional 4XTMF Transmitter Module is activated Piezo sounder turns on steady The alarm relay will transfer Trouble Condition Trouble condition indicates that one or more faults have been detected by the FACP. Contact the local service representative for immediate correction of the fault since FACP operation may be impaired. A Trouble condition will cause the following: The yellow System Trouble LED will light steady Additional trouble LEDs may turn on The piezo sounder will pulse 14 Document #50907 Rev.A1 12/03/02 P/N 50907:A1

15 GND AC TBL BUZ +24V ALARM REG RES NC NO TROUBLE NC NO SIGNAL INITIAT INITIAT OUTPUT ZONE 1 ZONE CUT IF 4X OPTION BOARD IS PRESENT BATTERY CUT TO DISABLE EARTH FAULT Circuits 1.4 Circuits Input Circuits The CMP-2401B has one IDC (Initiating Device Circuit) and the CMP-2402B has two IDCs. Input circuit(s) provide Style B (Class B) configuration and accept 2-wire smoke detectors and normally-open contact devices. Output Circuits 24 Volt Resettable Power Output 85 ma 24 Volt Battery Charger (up to two 7 AH batteries) Notification Appliance Circuit One Style Y (Class B) Notification Appliance 1.25 amps maximum Relays Two dry Form-C relays for system alarm and system trouble are provided standard. Contacts are rated VDC (resistive), VAC (resistive). Battery Charger The battery charger will charge up to two 7 AH batteries. The FACP cabinet holds a maximum of two 7 AH batteries. 1.5 Components Main Circuit Board The main circuit board contains power supply, alarm and trouble relays, control switches, LED indicators, option jumpers, wiring interface connectors and other primary components. The option module plugs in and is mounted to the main circuit board. The main circuit board is delivered premounted in the cabinet. NEUTRAL EARTH HOT TB1 J5 F2 C C TB2 R14 J4 SW1 SW2 SW3 SW4 R72 SYSTEM RESET SIG SILENCE ZONE 1 SIG SILENCE ZONE 2 TBL SILENCE 2402BORD.CDR Cabinet The cabinet is red. The backbox measures 14.5" (36.83 cm) high X 12.5" (31.75 cm) wide X 2.875" (7.303 cm) deep and provides space for two batteries (up to 7.0 Amp Hours each). Also supplied is a blue dress panel which mounts inside the cabinet. Dress Panel A blue dress panel, which is required for Canadian installations, is provided with the cabinet. The dress panel restricts access to the system wiring while allowing access to the control switches. TB3 J3 J1 MP2401DR.CDR DP-2401.CDR Transformer Assembly One transformer is provided standard with the panel. The transformer plugs into connector J5 on the main circuit board. Batteries The cabinet provides space for two 7 Amp Hour batteries which must be ordered separately. 2401XFOR.CDR 2401BATT.CDR Document #50907 Rev. A1 12/03/02 P/N 50907:A1 15

16 Optional Modules and Accessories 1.6 Optional Modules and Accessories 4XTMF Transmitter Module The 4XTMF Transmitter Module provides a supervised output for local energy municipal box transmitter and alarm and trouble reverse polarity. It includes a disable switch and disable trouble LED on the module. A jumper option on the module allows the reverse polarity circuit to open with a system trouble condition if no alarm condition exists. Remote Trouble Buzzer One Remote Trouble Buzzer can be connected to the FACP using four wires. The remote unit includes an AC LED, System Trouble LED and piezo sounder which are controlled by the control panel. It mounts to a singlegang electrical box. 16 Document #50907 Rev.A1 12/03/02 P/N 50907:A1

17 Installation CHAPTER 2 Installation 2.1 Mounting Options FIGURE 2-1:CMP-2401B/CMP-2402B Mounting The cabinet may be either semi-flush or surface mounted. The door is removable during the installation period by opening and lifting the door off the hinges. The cabinet mounts using two key slots and two additional (0.635 cm) diameter holes located in the backbox. The key slots are located at the top of the backbox and the two securing holes at the bottom. Carefully unpack the system and check for shipping damage. Mount the cabinet in a clean, dry, vibration-free area where extreme temperatures are not encountered. The area should be readily accessible with sufficient room to easily install and maintain the panel. Locate the top of the cabinet approximately five feet above the floor with the hinge mounting on the left. Determine the number of conductors required for the devices to be installed. Sufficient knockouts are provided for wiring convenience. Select the appropriate knockout(s) and pull the required conductors into the box. Note that there are no knockouts on the left (hinged) side of the cabinet. All wiring should be in accordance with the National and/or Local codes for fire alarm systems. MP2401DR.CDR 2.2 Backbox Mounting 1. Open the door. 2. Remove the main PC board assembly by unscrewing the four screws in the corners of the board. Set the board aside in a safe, clean place. Avoid static discharge which may damage the board. 3. Mark and predrill holes for the top two keyhole mounting bolts using the dimensions illustrated in Figure Install two upper fasteners in the wall with the screw heads protruding. 5. Using the upper keyholes, mount the backbox over the two screws. 6. Mark and drill the lower two holes. 7. Mount the backbox, install the remaining fasteners and tighten. 8. When the location is dry and free of construction dust, reinstall the main PC board. Document #50907 Rev. A1 12/03/02 P/N 50907:A1 17

18 Backbox Mounting Draw wires through the respective knockout locations. FIGURE 2-2:Cabinet Dimensions and Knockout Locations Top (2.858 cm) (2.223 cm) 1.25 (3.175 cm) ( cm) ( cm) ( cm) ( cm) (7.620 cm) (7.62 cm) (31.75 cm) 6.5 (16.51 cm) 1.25 (3.175 cm) (2.540 cm) 3.25 (8.255 cm) " ( cm) 1.75 (4.445 cm) " ( cm) ( cm) 14.5 (36.83 cm) 3.5 (8.89 cm) ( cm) " ( cm) TR-3-R Trim Ring (3.175 cm) (3.175 cm) ( cm) Bottom (7.620 cm) Right Side 5024JRBB.CDR 18 Document #50907 Rev.A1 12/03/02 P/N 50907:A1

19 Backbox Mounting FIGURE 2-3:FACP Backbox Top Depth=3.000 (7.620 cm) Door=12.714" ( cm) Backbox=12.5 (31.75 cm) Door=14.714" ( cm) Backbox=14.5" (36.83 cm) Bottom Right side 2401CABB.CDR Document #50907 Rev. A1 12/03/02 P/N 50907:A1 19

20 Operating Power! 2.3 Operating Power WARNING: Several different sources of power can be connected to this panel. Disconnect all sources of power before servicing. The panel and associated equipment may be damaged by removing and/or inserting modules, interconnecting cables or wiring while this unit is energized. Primary Power Source (AC) and Earth Ground Connections AC power connections are made inside the control panel cabinet. The AC input circuit is limited by fuse F2 (2 amp, 3AG Slow Blow). The primary power source for the FACP is 120 VAC, 60 Hz, 0.5 amps. Run a pair of wires (with ground conductor) from the protected premises main breaker box to TB3 of the main circuit board. As per the National and Canadian Electric Code, use 14 AWG (2.00 mm 2, 1.6 mm O.D.) or heavier gauge wire with 600V insulation. No other equipment may be connected to this circuit. In addition, this circuit must be provided with overcurrent protection and may not contain any power disconnect devices. A separate Earth Ground connection must be made to ensure proper panel operation and lightning and transient protection. Connect the Earth Ground wire [minimum 14 AWG (2.00 mm 2 )] to the grounding stud on the backbox. Do not use conduit for the Earth Ground connection since this does not provide reliable protection.! Secondary Power Source (Batteries) Observe polarity when connecting the battery. Connect the battery cable to J3 on the main circuit board using the plug-in connector and cable provided. The battery charger is current-limited and capable of recharging sealed lead acid type batteries. The charger shuts off when the system is in alarm. See Battery Calculations for calculation of the correct battery rating. WARNING: Battery contains sulfuric acid which can cause severe burns to the skin and eyes and can destroy fabrics. If contact is made with sulfuric acid, immediately flush the skin or eyes with water for 15 minutes and seek immediate medical attention. FIGURE 2-4:Operating Power Connections Grounding Stud GND AC TBL BUZ +24V REG RES ALARM TRO UBLE SIGNAL INITIAT INITIAT 2 NC C NO NC C OUTPUT ZONE 1 ZONE NO + + TB1 TB2 SW1 SYSTEM RESET SW2 SIG SILENCE ZONE 1 SW3 SIG SILENCE ZONE 2 Earth J5 CAUTION! HIGH VOLTAGE F2 R14 CUT IF 4X OPTION BOARD IS PRESENT SW4 TBL SILENCE J4 CUT TO DISABLE EARTH FAULT NEUTRAL EARTH HOT R72 TB3 J3 BATTERY J1 AC Hot Neutral 2402ACBX.CDR 20 Document #50907 Rev.A1 12/03/02 P/N 50907:A1

21 Input Circuits 2.4 Input Circuits The CMP-2401B has one IDC (Initiating Device Circuit) and the CMP-2402B has two IDCs. The maximum total loop resistance limit for each input circuit is 200 ohms. The field wiring is supervised for opens, shorts and ground faults. All conditions are visually and audibly annunciated. The zone(s) is a Style B (Class B) Initiating Device Circuit designed to accept any normally-open contact devices and conventional 2-wire or 4-wire, 24 VDC smoke detectors. Resettable power is provided via TB1 Terminals 24V Resettable (+) and Ground (-). Remove the End-of Line resistor from the FACP and install it on the IDC wiring after the last device in the circuit. Refer to the Fire Lite Device Compatibility Document for a list of compatible smoke detectors. It is allowable to mix an assortment of device types (i.e. smoke detectors, heat detectors, pull stations, etc.) on the same zone. FIGURE 2-5:CMP-2402B Style B Initiating Device Circuit Connections Style B (Class B) Initiating Device Circuit (supervised and power-limited). 3.9K ohm, ½ watt UL listed compatible 2-wire smoke detector Manual Pull Station Heat Detector Dummy load unused circuit TB1 GND AC TBL BUZ NC C NO NC C NO REMOTE +24 VDC RESET ALARM TROUBLE SIGNAL INITIATING OUTPUT ZONE 1 INITIATING ZONE 2 TB2 2402IDC.CDR Document #50907 Rev. A1 12/03/02 P/N 50907:A1 21

22 Output Circuits 2.5 Output Circuits DC Power Output Connections FIGURE 2-6:Auxiliary Power Connection 4-Wire Smoke Detector Power (85 ma) 24 VDC filtered, resettable power for 4-wire smoke detectors can be obtained from TB1 Terminals 24V Resettable (+) and Ground (-) TB GND AC TBL BUZ + NC C NO NC C NO REMOTE +24 VDC RESET ALARM TROUBLE SIGNAL OUTPUT INITIATING INITIATING ZONE 1 ZONE 2 TB2 2402TERM.CDR Notification Appliance Circuit The FACP provides one supervised Notification Appliance Circuit as Style Y (Class B). The circuit is capable of 1.25 amps of current. Observe polarity when connecting polarized devices to the NAC. Remove the End-of-Line resistor from the FACP and install it on the Notification Appliance Circuit wiring after the last device. Refer to the Fire Lite Device Compatibility Document for a listing of compatible notification appliances. FIGURE 2-7:Notification Appliance Circuit Connections Style Y (Class B) Notification Appliance Circuit (supervised). 3.9 K ohm, ½ watt Polarized Bell + Note: Notification Appliance polarities shown in alarm state Polarized Horn + Polarized Horn + Note: Terminal polarity shown in alarm state TB1 GND AC TBL BUZ+ NC C NO NC C NO REMOTE +24 VDC RESET ALARM TROUBLE SIGNAL INITIATING INITIATING OUTPUT ZONE1 ZONE2 TB2 2402NAC.CDR 22 Document #50907 Rev.A1 12/03/02 P/N 50907:A1

23 UL Power-limited Wiring Requirements Standard Relays The FACP provides two Form-C relays rated for VDC (resistive) and VAC (resistive). FIGURE 2-8:Relay Terminals Relay connections may be power-limited or nonpower-limited, provided that a minimum of 0.25" is maintained between conductors of power-limited and nonpower-limited circuits. ALARM TROUBLE TB1 GND AC TBL BUZ + NC C NO NC C NO TB2 SIGNAL OUTPUT INITIATING ZONE 1 INITIATING ZONE 2 M2401REL.CDR 2.6 UL Power-limited Wiring Requirements Power-limited and nonpower-limited circuit wiring must remain separated in the cabinet. All power-limited circuit wiring must remain at least 0.25" (6.35 mm) away from any nonpower-limited circuit wiring. Furthermore, all power-limited and nonpower-limited circuit wiring must enter and exit the cabinet through different knockouts and/or conduits. A typical wiring diagram for the FACP is illustrated below. FIGURE 2-9:Typical Wiring Diagram for UL Power-limited Requirements Grounding Stud Power-limited Circuit Nonpower-limited Circuit Power-limited Circuit GND AC TBL BUZ +24V REG RES ALARM TROUBLE SIGNAL INITIAT INITIAT 2 NO OUTPUT ZONE 1 ZONE C NO NC C NC + + TB1 TB2 SW1 SYSTEM RESET SW2 SIG SILENCE ZONE 1 SW3 SIG SILENCE ZONE 2 J5 CAUTION! HIGH VOLTAGE F2 R14 CUT IF 4X OPTION BOARD IS PRESENT J4 SW4 CUT TO DISABLE EARTH FAULT TBL SILENCE Power-limited Circuit NEUTRAL EARTH HOT R72 AC Power TB3 J3 BATTERY J1 2401PWRL.CDR Document #50907 Rev. A1 12/03/02 P/N 50907:A1 23

24 Installation of Optional Module 2.7 Installation of Optional Module CAUTION: Remove all power (AC and DC) before installing or removing modules or wiring XTMF Transmitter Module Push the disconnect switch to the down position to prevent accidental activation of the municipal box during testing of the control panel. The Disconnect LED will remain illuminated while the municipal box is disconnected. The System Trouble LED will indicate disconnected and/or open circuit conditions on the municipal box. During trouble conditions, it is possible to obtain the circuit condition on the alarm reverse polarity output. If this operation is desired, cut the TBL jumper on the 4XTMF module. FIGURE 2-10:4XTMF Module Connections TROUBLE SIGNAL INITIAT INITIAT OUTPUT ZONE 1 ZONE 2 NO NC C TB2 SW1 SYSTEM RESET 2402BRD2.CDR SW2 SIG SILENCE ZONE 1 Cut R14 for 4XTMF module placement supervision CUT IF 4X OPTION BOARD IS PRESENT SW3 SW4 SIG SILENCE ZONE 2 TBL SILENCE 4XTMF Module Polarities are shown for module activation R14 TBL Jumper J4 CUT TO DISABLE EARTH FAULT 1 (+) Remote Alarm (power-limited)* 2 (-) 3 (+) Remote Trouble (power-limited)* 4 (-) 5 no connection 6 (+) Municipal Box (nonpower-limited)* 7 (-) Install 4XTMF Module by plugging into connector J6 and J7 on CMP-2401B/02B main board R72 * Wiring from these terminals can exit the protected premises. Disconnect Switch Disconnect LED J3 BATTERY J1 4XTMF.CDR 24 Document #50907 Rev.A1 12/03/02 P/N 50907:A1

25 Installation of Optional Module RTB - Remote Trouble Buzzer The RTB is a Remote Trouble Buzzer which provides a green AC Power LED and a yellow Trouble LED along with a piezo sounder, all of which mimic the condition of the control panel. The RTB can be mounted remotely in a single-gang electrical box. Four wires are required to connect the RTB to the CMP-2401B/CMP-2402B control panel as illustrated in Figure FIGURE 2-11:RTB Remote Trouble Buzzer Connection RTB Remote Trouble Buzzer Ground Trouble LED RTBBUZZ.CDR AC Power LED Buzzer CMP-2401B/CMP-2402B TB1 GND AC TBL BUZ +24V ALARM TROUBLE SIGNAL REG OUTPUT INITIAT INITIAT ZONE 1 ZONE 2 RES NC NO NC NO C C TB2 J5 F2 2402RTB.CDR Document #50907 Rev. A1 12/03/02 P/N 50907:A1 25

26 Programming Options CHAPTER 3 Programming Options This chapter describes the programming options available by cutting resistors on the FACP main circuit board. Options should be selected (resistors cut if necessary) prior to applying power to the control panel. 3.1 Earth Ground Fault Detection The FACP is factory configured to automatically detect ground fault conditions. A ground fault occurs when a low resistance is detected between an FACP circuit and earth ground. This condition will cause the System Trouble LED and Ground Fault LED to turn on and the piezo sounder to pulse. The Ground Fault Detection circuit can be disabled by cutting resistor R72 on the main circuit board. Refer to the local codes and consult the local Authority Having Jurisdiction before disabling the Ground Fault Detection circuit. FIGURE 3-1:Ground Fault Detection Circuit J4 CUT TO DISABLE EARTH FAULT NEUTRAL EARTH HOT R72 R72 Cut to Disable Ground Fault Detection TB3 J3 BATTERY J1 2402BRD3.CDR 3.2 Optional 4XTMF Transmitter Module Placement Supervision The 4XTMF module can be used to connect the FACP to a City Box or Reverse Polarity Remote Station. To supervise placement and operation of the module, cut resistor R14. Refer to the local codes and consult the local Authority Having Jurisdiction before installing the 4XTMF Transmitter Module. FIGURE 3-2:4XTMF Module Placement Supervision J5 R14 CUT IF 4X OPTION BOARD IS PRESENT SW4 TBL SILENCE 2402BRD4.CDR R14 Cut to Supervise Placement of 4XTMF Module when installed 26 Document #50907 Rev.A1 12/03/02 P/N 50907:A1

27 Periodic Testing and Maintenance CHAPTER 4 Periodic Testing and Maintenance To ensure proper and reliable operation, it is recommended that system inspection and testing be scheduled monthly or as required by national and/or local fire codes. Testing should be done by a qualified service representative if a malfunction is encountered. Before Testing: 1. Notify the fire department and/or central alarm receiving station if an alarm condition will be transmitted. 2. Notify the facility personnel of a test so that alarm sounding devices are ignored during the test period. 3. When necessary, activation of notification appliances can be prevented by using the Signal Silence switch to silence the zone. Testing: 1. Activate a zone via an alarm initiating device and check that active notification appliances sound and the alarm LED lights. Reset the system and repeat the procedure for each zone*. 2. Momentarily activate the following switches (one at a time) and check for a trouble signal: Reset (all LEDs should illuminate for Lamp Test) Signal Silence 3. Depress the Trouble Silence switch and check for an intermittent audible signal. Return the Trouble Silence switch to the normal position. 4. Momentarily open the following circuits one at a time and check for a trouble signal: Notification Appliance (bell) Circuit Initiating Device Circuit Zone 1 Initiating Device Circuit Zone 2 (CMP-2402B only) 5. If new batteries were installed, wait 48 hours before completing this step. Remove AC power, activate a zone and check that: The Alarm LED lights All active notification appliances sound Measure battery voltage while the notification appliances are sounding. Replace any battery with terminal voltage less than 85% of rating. Reapply AC power and press the Reset switch*. 6. Return all switches to their normal positions. Notify the fire department, central station and/or building personnel that testing is completed. *Note that the Reset and Signal Silence switches will not operate for one minute following activation of an alarm. Document #50907 Rev. A1 12/03/02 P/N 50907:A1 27

28 Battery Calculations CHAPTER 5 Battery Calculations Use the Total Standby and Alarm Load Currents calculated in Table 5-2 and Table 5-3 for the following battery calculation. TABLE 5-1: Battery Calculations Standby Load Current (amps) [ ] X Required Standby Time in Hours (24 or 60 Hours) [ ] = Alarm Load Current (amps) [ ] X Required Alarm Time in Hours (i.e. 5 minutes = minutes = 0.167) [ ] = Add Standby and Alarm Load for Required Ampere Hour Battery = Multiply by the Derating Factor of 1.2 X1.2 Total Ampere Hours (AH) Required = Note: 1. 7 Ampere Hour battery can be located in the backbox. 28 Document #50907 Rev.A1 12/03/02 P/N 50907:A1

29 The Main Power Supply 5.1 The Main Power Supply The FACP provides filtered power for operating the fire alarm control panel, external devices and the standby battery. The power for operating external devices is limited. Use Table 5-2 (standby or nonalarm) and Table 5-3 (alarm) to determine if external loading is within the capabilities of the power supply. For 4-wire smoke detectors, be sure to power them from TB1 Terminals (+24V Resettable) and (-Ground). TABLE 5-2: Load in Standby Device Type # of Devices Current (amps) Total Current (amps) Main Circuit Board 1 X = XTMF (1 max.) X = Remote Trouble Unit (1 max.) X = 2-wire Detector Heads [ ] X [ ] 1 = 4-wire Detector Heads [ ] X [ ] 1 = Power Supervision Relays 2 [ ] X [ ] = Additional Current Draw from TB1 (nonalarm) 3 = Sum Column for Standby Load = amps 1. Refer to the Device Compatibility Document for 2-wire smoke detector standby current. 2. Must use compatible listed Power Supervision Relay. 3. The total standby current must include the resettable power from TB1. Caution must be taken to ensure that current drawn from this output during alarm does not exceed maximum ratings specified (see Table 5-3 ) Document #50907 Rev. A1 12/03/02 P/N 50907:A1 29

30 The Main Power Supply TABLE 5-3: Load in Alarm Device Type # of Devices Current (amps) Total Current (amps) Main Circuit Board 1 X = 4XTMF (1 max.) X = Remote Trouble Unit (1 max.) X = 4-wire Detector Heads 2 [ ] X [ ] = Power Supervision Relays 3 [ ] X [ ] = Notification Appliances 4 [ ] X [ ] = Additional Current Draw from TB1 (nonalarm) 2 = Sum Column for Alarm Load = amps 1. The current shown represents the CMP-2401B control panel in alarm. If both zones of the CMP-2402B control panel are in alarm, the current draw increases to amps. 2. Current limitations of terminals: TB1, Terminals Ground and +24V Resettable = amps, filtered, 24 VDC +/-5%, 10mV RMS. 3. Must use compatible listed Power Supervision Relay 4. Enter current draw of each device. Current limitation of TB2 Notification Appliance Circuit is 1.25 amps. 30 Document #50907 Rev.A1 12/03/02 P/N 50907:A1

31 Index Numerics 4XTMF see Transmitter Module A Alarm 14 B Backbox 19 Battery 15 Alarm 30 Calculations 28 Charger 15 see also Power - Battery Standby 29 Trouble 13 C Cabinet 15 Dimensions 18 Knockouts 18 see also Backbox D Description 9 Discharge Protection 11 Dress Panel 15 E Earth Ground 20 Fault Detection 26 F Form-C Relays See also Relays G Ground Fault see also Earth Ground - Fault Detection I Indicators 13 AC Power 13 Battery Trouble 13 Bell Trouble 13 Ground Fault 14 Option Trouble 13 System Trouble 14 see also Trouble Zone Alarm 13 see also Alarm Zone Silence 13 Zone Trouble 13 Initiating Device Circuit Current Alarm 11 Short Circuit 11 Standby 11 End-of-Line Resistor 11 Style Y 11 Voltage 11 Input Circuits 15, 21 L LED see Indicators M Maintenance 27 Mounting 17 N Notification Appliance Circuit 11, 15, 22 Current 11 End-of-Line Resistor 11 Style Y 11 Voltage 11 O Operational Power 20 Primary 20 see Battery Output Circuits 22 Resettable Power 15 see Battery - Charger P Piezo see Sounder Power AC 11 AC fuse 11 see also Operational Power - Primary Battery 11 Charger Capacity 11 charging circuit 11 Deep Discharge Protection 11 Programming 26 R Relays 11, 15, 23 Contact Rating 11 Remote Trouble Buzzer 16, 25 Resettable Power Current 11 voltage 11 Resistor, End-of-Line Initiating Device Circuit 11 Notification Appliance Circuit 11 RTB see Remote Trouble Buzzer S Sounder Alarm 14 Trouble 14 Standby 14 Style B 9 Style Y 9 Switches 12 Reset 12 Signal Silence 12 Trouble Silence 12 T Testing 27 Transformer Assembly 15 Transmitter Module 16, 24 Placement Supervision 26 Trouble 14 U UL Power-limited Wiring 23 Document #50907 Rev. A1 12/03/02 P/N 50907:A1 31

32 Notes 32 Document #50907 Rev.A1 12/03/02 P/N 50907:A1

33 Notes Document #50907 Rev.A1 12/03/02 P/N 50907:A1 33

34 Notes 34 Document #50907 Rev.A1 12/03/02 P/N 50907:A1

35 Limited Warranty The manufacturer warrants its products to be free from defects in materials and workmanship for eighteen (18) months from the date of manufacture, under normal use and service. Products are date-stamped at time of manufacture. The sole and exclusive obligation of the manufacturer is to repair or replace, at its option, free of charge for parts and labor, any part which is defective in materials or workmanship under normal use and service. For products not under the manufacturer's date-stamp control, the warranty is eighteen (18) months from date of original purchase by the manufacturer's distributor unless the installation instructions or catalog sets forth a shorter period, in which case the shorter period shall apply. This warranty is void if the product is altered, repaired, or serviced by anyone other than the manufacturer or its authorized distributors, or if there is a failure to maintain the products and systems in which they operate in a proper and workable manner. In case of defect, secure a Return Material Authorization form from our customer service department. Return product, transportation prepaid, to the manufacturer. This writing constitutes the only warranty made by this manufacturer with respect to its products. The manufacturer does not represent that its products will prevent any loss by fire or otherwise, or that its products will in all cases provide the protection for which they are installed or intended. Buyer acknowledges that the manufacturer is not an insurer and assumes no risk for loss or damages or the cost of any inconvenience, transportation, damage, misuse, abuse, accident, or similar incident. THE MANUFACTURER GIVES NO WARRANTY, EXPRESSED OR IMPLIED, OF MERCHANTABILITY, FITNESS FOR ANY PARTICULAR PURPOSE, OR OTHERWISE WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE HEREOF. UNDER NO CIRCUMSTANCES SHALL THE MANUFACTURER BE LIABLE FOR ANY LOSS OF OR DAMAGE TO PROPERTY, DIRECT, INCIDENTAL, OR CONSEQUENTIAL, ARISING OUT OF THE USE OF, OR INABILITY TO USE THE MANUFACTURER'S PRODUCTS. FURTHERMORE, THE MANUFACTURER SHALL NOT BE LIABLE FOR ANY PERSONAL INJURY OR DEATH WHICH MAY ARISE IN THE COURSE OF, OR AS A RESULT OF, PERSONAL, COMMERCIAL, OR INDUSTRIAL USE OF ITS PRODUCTS. This warranty replaces all previous warranties and is the only warranty made by the manufacturer. No increase or alteration, written or verbal, of the obligation of this warranty is authorized. LimWarLg.p65 01/10/2000

Instruction Manual. CMP-12/24 Fire Alarm Control Panel. 12 Clintonville Road, Northford, CT DOCUMENT /11/96 REV: D1

Instruction Manual. CMP-12/24 Fire Alarm Control Panel. 12 Clintonville Road, Northford, CT DOCUMENT /11/96 REV: D1 12 Clintonville Road, Northford, CT 06472 Instruction Manual CMP-12/24 Fire Alarm Control Panel DOCUMENT 15819 3/11/96 REV: D1 P/N 15819:D1 ECN 96-047 Installation Precautions - Adherence to the following

More information

MS-2410BC. Conventional Fire Alarm Control Panel. Programming, Installation, Maintenance and Operating Instruction Manual

MS-2410BC. Conventional Fire Alarm Control Panel. Programming, Installation, Maintenance and Operating Instruction Manual 24 Viceroy Road Unit #6 & 7 Concord, Ontario L4K2L9 Phone (905) 660-7210 FAX: (905) 660-7204 MS-2410BC Conventional Fire Alarm Control Panel Programming, Installation, Maintenance and Operating Instruction

More information

The RPT-485W/RPT-485WF

The RPT-485W/RPT-485WF 12 Clintonville Road Northford, CT 06472 203/484-7161 FAX: 203/484-7118 The RPT-485W/RPT-485WF EIA-485 Annunciator Loop Repeater for Twisted Pair Wiring/Fiber Optic Cable Document 15640 08/13/97 Revision:

More information

HP101U Conventional Fire Alarm Control Panel Installation And Operation Manual

HP101U Conventional Fire Alarm Control Panel Installation And Operation Manual HP101U Conventional Fire Alarm Control Panel Installation And Operation Manual NOTICE All information, documentation, and specifications contained in this manual are subject to change without prior notice

More information

Fire Alarm Control Panels MS-2 & MS-4 MS-2E & MS-4E. Instruction Manual. Document /6/2014 Rev: G3 P/N 51512:G3 ECN

Fire Alarm Control Panels MS-2 & MS-4 MS-2E & MS-4E. Instruction Manual. Document /6/2014 Rev: G3 P/N 51512:G3 ECN Fire Alarm Control Panels MS-2 & MS-4 MS-2E & MS-4E Instruction Manual Document 51512 8/6/2014 Rev: G3 P/N 51512:G3 ECN 14-523 Fire Alarm & Emergency Communication System Limitations While a life safety

More information

FireNET FN-LCD-S Serial Annunciator Installation and Operation Manual

FireNET FN-LCD-S Serial Annunciator Installation and Operation Manual FireNET FN-LCD-S Serial Annunciator Installation and Operation Manual Hochiki America Corporation 7051 Village Drive, Suite 100 Buena Park, CA 90621-2268 714.522.2246 Corporate Headquarters 800.845.6692

More information

MS-4012/4024 and CMS-4012/4024. Instruction Manual for the. Fire Alarm Control Panels

MS-4012/4024 and CMS-4012/4024. Instruction Manual for the. Fire Alarm Control Panels R 12 Clintonville Road, Northford, CT 06472 Phone: (203) 484-7161 FAX: (203) 484-7118 Instruction Manual for the MS-4012/4024 and CMS-4012/4024 Fire Alarm Control Panels Document 15586 5/11/93 Revision:

More information

CFP-2410B. Programming, Installation, Maintenance and Operating Manual. Conventional Fire Alarm Control Panel.

CFP-2410B. Programming, Installation, Maintenance and Operating Manual. Conventional Fire Alarm Control Panel. Conventional Fire Alarm Control Panel CFP-2410B Programming, Installation, Maintenance and Operating Manual Document 50974 2/18/04 Rev: B P/N 50974:B ECN 02-253 Fire Alarm System Limitations While a fire

More information

PN:51264:A2 ECN Remote Fire Annunciator FDU-80. Document /14/00 Rev: A.

PN:51264:A2 ECN Remote Fire Annunciator FDU-80. Document /14/00 Rev: A. PN:51264:A2 ECN 00-245 Remote Fire Annunciator FDU-80 Document 51264 6/14/00 Rev: A Fire Alarm System Limitations An automatic fire alarm system typically made up of smoke detectors, heat detectors, manual

More information

Field Charger/Power Supply FCPS-24S6 FCPS-24S8. Document # /06/03 Revision: C1 PN: 51977:C1 ECN

Field Charger/Power Supply FCPS-24S6 FCPS-24S8. Document # /06/03 Revision: C1 PN: 51977:C1 ECN Field Charger/Power Supply FCPS-S6 FCPS-S8 Document #977 8/06/0 Revision: C PN: 977:C ECN 0-96 Fire Alarm System Limitations While a fire alarm system may lower insurance rates, it is not a substitute

More information

The MS-4412B/MS-4424B(E) FIRE ALARM CONTROL PANELS

The MS-4412B/MS-4424B(E) FIRE ALARM CONTROL PANELS The MS-4412B/MS-4424B(E) FIRE ALARM CONTROL PANELS 12 Clintonville Road, Northford CT 06472 DOCUMENT 15125 06/24/97 Rev: F1 ECN 97-192 Installation Precautions - Adherence to the following will aid in

More information

HPFF8(E)/HPFF8CM(E) NOTIFICATION APPLIANCE CIRCUIT EXPANDER INSTALLATION & OPERATION MANUAL

HPFF8(E)/HPFF8CM(E) NOTIFICATION APPLIANCE CIRCUIT EXPANDER INSTALLATION & OPERATION MANUAL HPFF8(E)/HPFF8CM(E) NOTIFICATION APPLIANCE CIRCUIT EXPANDER INSTALLATION & OPERATION MANUAL P/N 53499:B3 ECN 16-562 10/5/2016 Fire Alarm & Emergency Communication System Limitations While a life safety

More information

Cautions and Warnings. Introduction 4009 NAC POWER EXTENDER

Cautions and Warnings. Introduction 4009 NAC POWER EXTENDER Cautions and Warnings DO NOT INSTALL ANY SIMPLEX PRODUCT THAT APPEARS DAMAGED. Upon unpacking your Simplex product, inspect the contents of the carton for shipping damage. If damage is apparent, immediately

More information

Lamp Driver Module LDM-32F

Lamp Driver Module LDM-32F PN 50055:C0 ECN 01-155 Lamp Driver Module LDM-32F Instruction Manual Document 50055 03/20/2001 Rev: C Fire Alarm System Limitations An automatic fire alarm system typically made up of smoke detectors,

More information

AFP-100 Intelligent Fire Panel

AFP-100 Intelligent Fire Panel One Fire-Lite Place Northford, CT 06472 (203) 484-7161 (203) 484-7118 (Fax) AFP-100 Intelligent Fire Panel Installation, Programming and Operating Manual Document 51010 A 12/15/98 Revision PN 51010:A ECN

More information

MR-2602 Two Zone Fire Alarm Control Panel

MR-2602 Two Zone Fire Alarm Control Panel MR-2602 Two Zone Fire Alarm Control Panel Installation Manual Secutron LT-2015 Rev.3 July 2010 Table of Contents 1 Introduction 1.1 The MR-2602 Fire Alarm Control Unit... 11 1.1.1 General features...

More information

Model SK Installation and Operations Manual. Fire Control / Communicator. Document Rev: P P/N :P ECN:

Model SK Installation and Operations Manual. Fire Control / Communicator. Document Rev: P P/N :P ECN: Model SK-5208 Fire Control / Communicator Installation and Operations Manual Document 151204 Rev: P P/N 151204:P ECN: 17-0298 Installation Procedure Adherence to the following will aid in problem-free

More information

PN: 52626:A1 ECN Fire Alarm Control Panels MS-5UD & MS-10UD Series. Document # /11/07 Revision: A1

PN: 52626:A1 ECN Fire Alarm Control Panels MS-5UD & MS-10UD Series. Document # /11/07 Revision: A1 PN: 52626:A1 ECN 07-248 Fire Alarm Control Panels MS-5UD & MS-10UD Series Document #52626 5/11/07 Revision: A1 Fire Alarm System Limitations While a fire alarm system may lower insurance rates, it is not

More information

12 Clintonville Road, Northford, CT Technical Manual MS-9200 DOCUMENT # /28/97 REV: B P/N 50428:B1 ECN

12 Clintonville Road, Northford, CT Technical Manual MS-9200 DOCUMENT # /28/97 REV: B P/N 50428:B1 ECN 12 Clintonville Road, Northford, CT 06472 Technical Manual MS-9200 Addressable Fire Control Panel (Export Version) DOCUMENT # 50428 7/28/97 REV: B P/N 50428:B1 ECN 97-316 Installation Precautions - Adherence

More information

Fire Alarm Control Panels. MS-5UD Series MS-10UD Series. Manual. Document /7/2014 Rev: C4 P/N 52626:C4 ECN

Fire Alarm Control Panels. MS-5UD Series MS-10UD Series. Manual. Document /7/2014 Rev: C4 P/N 52626:C4 ECN Fire Alarm Control Panels MS-5UD Series MS-10UD Series Manual Document 52626 3/7/2014 Rev: C4 P/N 52626:C4 ECN 14-167 Fire Alarm & Emergency Communication System Limitations While a life safety system

More information

Fire Alarm Control Panels. MS-5UD Series MS-10UD Series. Manual. Document /24/2012 Rev: C2 P/N 52626:C2 ECN

Fire Alarm Control Panels. MS-5UD Series MS-10UD Series. Manual. Document /24/2012 Rev: C2 P/N 52626:C2 ECN Fire Alarm Control Panels MS-5UD Series MS-10UD Series Manual Document 52626 1/24/2012 Rev: C2 P/N 52626:C2 ECN 12-056 Fire Alarm System Limitations While a fire alarm system may lower insurance rates,

More information

/9308 External Battery Chargers Installation Instructions

/9308 External Battery Chargers Installation Instructions 4081-9306/9308 External Battery Chargers Installation Instructions Introduction This publication describes the installation procedure for an External Battery Charger used with the 4100U or 4100ES System.

More information

Specification/ Data Sheet

Specification/ Data Sheet Specification/ Data Sheet TRITON RP Agent Release Control Panel FEATURES Agent Release Control Panel designed specifically for suppression release operation with: Four initiating device circuits (IDCs)

More information

Emergency Command Center ECC-50/100 ECC-50/100E. Instruction Manual. Document LS FL-E 5/3/2016 Rev: G P/N LS FL-E:G ECN

Emergency Command Center ECC-50/100 ECC-50/100E. Instruction Manual. Document LS FL-E 5/3/2016 Rev: G P/N LS FL-E:G ECN Emergency Command Center ECC-50/100 ECC-50/100E Instruction Manual Document LS10001-000FL-E 5/3/2016 Rev: G P/N LS10001-000FL-E:G ECN 16-212 Fire Alarm & Emergency Communication System Limitations While

More information

AL802ULADA. NAC Power Extender. Installation Guide. (See Application Guide for additional information)

AL802ULADA. NAC Power Extender. Installation Guide. (See Application Guide for additional information) AL802ULADA NAC Power Extender Installation Guide (See Application Guide for additional information) Rev. 042010 Agency Listings: UL Listed Control Units for Fire Protective Signaling Systems (UL 864).

More information

Liquid Crystal Display LCD-160. Manual. Document /26/2003 Rev: A P/N 51850:A ECN

Liquid Crystal Display LCD-160. Manual. Document /26/2003 Rev: A P/N 51850:A ECN Liquid Crystal Display LCD-160 Manual Document 51850 09/26/2003 Rev: A P/N 51850:A ECN 03-419 Fire Alarm System Limitations While a fire alarm system may lower insurance rates, it is not a substitute for

More information

ACC-25/50ZST. Zoned System Voice with Telephone Evacuation Control Panel

ACC-25/50ZST. Zoned System Voice with Telephone Evacuation Control Panel ACC-25/50ZST Zoned System Voice with Telephone Evacuation Control Panel General The AUDIO COMMAND CENTER 25/50 Zone System with FireFighters Telephone (ACC-25/50ZST) is a state-of-the-art Emergency Voice

More information

Installation, Operating and Maintenance Manual

Installation, Operating and Maintenance Manual STATUS ZONES CONTROLS FIRE FAULT DISABLED FIRE 1 2 3 4 5 6 7 8 TEST FAULT DISABLED 1 5 BUZZER SILENCE RESET 1 2 TEST 2 6 LAMP TEST 3 SUPPLY 3 7 SYSTEM FAULT 4 8 SOUNDERS ACTIVATE/ SILENCE 4 FAULTS INSTRUCTIONS

More information

GasScanner 8C. Eight Channel Monitor. Operator s Manual. MINT-0281-XX Rev. A 01/29/08

GasScanner 8C. Eight Channel Monitor. Operator s Manual. MINT-0281-XX Rev. A 01/29/08 GasScanner 8C Eight Channel Monitor Operator s Manual MINT-0281-XX Rev. A 01/29/08 Product Warranty Matheson Tri-Gas, Inc., warrants gas alarm equipment sold by us to be free from defects in materials,

More information

December Scorpio. Fire Control Panel. Installation, Operation & Maintenance Manual. P/N UL Listing File No. S2422.

December Scorpio. Fire Control Panel. Installation, Operation & Maintenance Manual. P/N UL Listing File No. S2422. December 2001 Scorpio TM Fire Control Panel Installation, Operation & Maintenance Manual P/N 06-235793-001 UL Listing File No. S2422 Fire Systems SAFETY SUMMARY Installation Precautions Adherence to the

More information

MS-9200UDLS MS-9200UDLSE. Fire Alarm Control Panel

MS-9200UDLS MS-9200UDLSE. Fire Alarm Control Panel PN: 52750:A ECN 05-680 Fire Alarm Control Panel MS-9200UDLS MS-9200UDLSE IMPORTANT! The SLC Manual Document #51309 must be referenced in addition to this manual when installing or servicing the Fire Alarm

More information

Electric Release Panel Wiring Tips

Electric Release Panel Wiring Tips R IPS CARBO STEEL PIPE FIRE PROTECTIO PRODUCTS Electric Release Panel Wiring Tips 30.4 VICTAULIC IS A ISO 900 CERTIFIED COMPAY Model PDRP-00 Releasing Panels are compact single enclosure units containing

More information

Wiring Instructions for the 2900 Series FIREGUARD Combination Door Closer-Holder and Releasing Device with Integral Smoke Detector

Wiring Instructions for the 2900 Series FIREGUARD Combination Door Closer-Holder and Releasing Device with Integral Smoke Detector Wiring Instructions for the 900 Series FIREGUARD Combination Door Closer-Holder and Releasing Device with Integral Smoke Detector CAUTION: FAILURE TO INSTALL OR ADJUST PROPERLY MAY RESULT IN INJURY OR

More information

ACSI AO ELECTRIC LATCH RETRACTION CONTROLLER INSTALLATION INSTRUCTIONS I.D. 1089, REV. F

ACSI AO ELECTRIC LATCH RETRACTION CONTROLLER INSTALLATION INSTRUCTIONS I.D. 1089, REV. F II 1400-2 ACSI 1406-04-AO ELECTRIC LATCH RETRACTION CONTROLLER INSTALLATION INSTRUCTIONS I.D. 1089, REV. F INSTALLATION Transformer Model BE31763001 by Basler Electric, Transformer Model 2010028 by Galaxy

More information

* These Remote Mics must be SPRM-GP

* These Remote Mics must be SPRM-GP 273 Branchport Avenue Long Branch, NJ 07740 (800) 6312148 Thank you for using our products. www.coopernotification.com INSTALLATION INSTRUCTIONS REMOTE MICROPHONE EXPANSION MODULE Use this product according

More information

AL802ULADA. NAC Power Extender. Installation Guide. (See Application Guide for additional information) Rev

AL802ULADA. NAC Power Extender. Installation Guide. (See Application Guide for additional information) Rev AL802ULADA NAC Power Extender Installation Guide (See Application Guide for additional information) Rev. 031703 Overview: The Altronix AL802ULADA is an extremely cost effective 8 amp voltage regulated

More information

Digital Alarm Communicator/Transmitters 411/411UD. Manual. Document LS GE-E 1/29/2014 Rev: A P/N LS GE-E:A ECN

Digital Alarm Communicator/Transmitters 411/411UD. Manual. Document LS GE-E 1/29/2014 Rev: A P/N LS GE-E:A ECN Digital Alarm Communicator/Transmitters 411/411UD Manual Document LS10105-000GE-E 1/29/2014 Rev: A P/N LS10105-000GE-E:A ECN 13-875 Fire Alarm & Emergency Communication System Limitations While a life

More information

Advanced Life Safety Solutions. FA-103 and FA-106. Fire Alarm Control Panels. Installation and Operation Manual

Advanced Life Safety Solutions. FA-103 and FA-106. Fire Alarm Control Panels. Installation and Operation Manual Advanced Life Safety Solutions FA-103 and FA-106 Fire Alarm Control Panels Installation and Operation Manual LT-1200 Rev 0 February 2017 FA-106 Fire Alarm Control Panel Table of Contents Introduction...

More information

RELEASE DEVICE CONTROLS

RELEASE DEVICE CONTROLS RELEASE DEVICE CONTROLS RELEASE DEVICE MODEL C+ INSTALLATION MANUAL UL LISTED CANADIAN LISTED CSFM: 7300-48:00 GENERAL DESCRIPTION: MADE IN THE U.S.A. S/N: The LM0-C+ Release Device/Control Panel is a

More information

FireSeeker Fire Alarm Control Panel Model FS-250 Installation, Operation and Maintenance Manual

FireSeeker Fire Alarm Control Panel Model FS-250 Installation, Operation and Maintenance Manual FireSeeker Fire Alarm Control Panel Model FS-250 Installation, Operation and Maintenance Manual P/N 315-049353-1 Siemens Building Technologies Fire Safety TABLE OF CONTENTS INTRODUCTION... 1 CONTROL PANEL

More information

FireSeeker Fire Alarm Control Panel Model FS-100 Installation, Operation, and Maintenance Manual

FireSeeker Fire Alarm Control Panel Model FS-100 Installation, Operation, and Maintenance Manual Fire Safety FireSeeker Fire Alarm Control Panel Model FS-100 Installation, Operation, and Maintenance Manual Siemens Building Technologies, Inc. Siemens Building Technologies, Ltd. 8 Fernwood Road 2 Kenview

More information

Series SPB Audio Boosters Installation, Testing, Operation, and Maintenance Manual

Series SPB Audio Boosters Installation, Testing, Operation, and Maintenance Manual Series SPB Audio Boosters Installation, Testing, Operation, and Maintenance Manual Part Number P84748 Assembly Number A84749 Revision C Revision A Copyright 2006 Printed in U.S.A. All rights reserved.

More information

MMF Six Zone Interface Module

MMF Six Zone Interface Module Installation and Maintenance Instructions I56-900-005 MMF-0-6 Six Zone Interface Module SPECIFICATIONS Normal Operating Voltage: 5- VDC Stand-By Current: ma Alarm Current: 40 ma (assumes all six LEDs solid

More information

Macurco HD-11 Hydrogen Gas Detector

Macurco HD-11 Hydrogen Gas Detector Macurco HD-11 Hydrogen Gas Detector User Instructions Important: Keep these User Instructions for reference TABLE OF CONTENTS GENERAL SAFETY INFORMATION 3 Intended Use 3 List of Warnings and Cautions 3

More information

Long Range Radio Alarm Transmitter

Long Range Radio Alarm Transmitter TM Long Range Radio Alarm Transmitter INSTALLATION MANUAL Version 1.3W FEATURES Transmits alarm information to a long range radio network Varitech Transmission Format Note: If automatic SIA is used in

More information

PS6 SERIES. Installation PS6 SERIES. Power Supplies c/w Fire Panel Interface, EOL Trigger and Standby Power Option

PS6 SERIES. Installation PS6 SERIES. Power Supplies c/w Fire Panel Interface, EOL Trigger and Standby Power Option Installation PS6 SERIES Power Supplies PS6 SERIES Power Supplies c/w Fire Panel Interface, EOL Trigger and Standby Power Option Installation and Specifications Manual ISDPS6_SERIES 08121590 PCN15016 R05/15GR

More information

Table 1: dba Ratings for AMT Multitone Signal Typical Anechoic dba at 10 Feet per CAN/ULC S525-07

Table 1: dba Ratings for AMT Multitone Signal Typical Anechoic dba at 10 Feet per CAN/ULC S525-07 273 Branchport Avenue Long Branch, NJ 07740 (800) 631-2148 (USA) Thank you for using our products. (800) 397-5777 (CANADA) www.coopernotification.com GENERAL: INSTALLATION INSTRUCTIONS AMT MULTITONE APPLIANCES

More information

FMR Installation Instructions. Addressable Fire System Controller

FMR Installation Instructions. Addressable Fire System Controller FMR-7033 EN Installation Instructions Addressable Fire System Controller EN 2 FMR-7033 Installation Instructions Contents Contents Contents...2 1.0 Introduction...3 2.0 Description...3 3.0 Device Mounting...3

More information

Beacon 410A Gas Monitor Operator s Manual

Beacon 410A Gas Monitor Operator s Manual Beacon 410A Gas Monitor Operator s Manual Part Number: 71-0397 Revision: F Released: 12/5/17 www.rkiinstruments.com Product Warranty RKI Instruments, Inc., warrants gas alarm equipment sold by us to be

More information

LDM Series Lamp Driver Modules For Graphic Annunciation and Control

LDM Series Lamp Driver Modules For Graphic Annunciation and Control 12 Clintonville Road Northford, CT 06472 (203) 484-7161 FAX: (203) 484-7118 LDM Series Lamp Driver Modules For Graphic Annunciation and Control Used with the System 500, System 5000, AM2020/AFP1010 and

More information

MPC-6000 / MPC-7000 / RND-2

MPC-6000 / MPC-7000 / RND-2 MPC-6000 / MPC-7000 / RND-2 Fire Alarm System Control Unit Installation, Operation and Maintenance Manual Siemens Building Technologies, Inc. 8 Fernwood Road Florham Park, NJ 07932 Tel: (973) 593-2600

More information

PNC 1000 SERIES 2, 4, 8 Zone Fire Alarm Control Panel

PNC 1000 SERIES 2, 4, 8 Zone Fire Alarm Control Panel PNC 1000 SERIES 2, 4, 8 Zone Fire Alarm Control Panel INSTALLATION, OPERATION AND MAINTENANCE MANUAL Version: CN-PM-1000.VER1.1-12/2012 EN54 INFORMATION In accordance with EN 54-2 clause 13.7, the maximum

More information

Intelligent Control Panel SLC. Wiring Manual. Document /17/2014 Rev: P4 P/N 51309:P4 ECN

Intelligent Control Panel SLC. Wiring Manual. Document /17/2014 Rev: P4 P/N 51309:P4 ECN Intelligent Control Panel SLC Wiring Manual Document 51309 9/17/2014 Rev: P4 P/N 51309:P4 ECN 14-790 Fire Alarm & Emergency Communication System Limitations While a life safety system may lower insurance

More information

Installation and user manual for the FX range of fire panels. 1, 2, 4 and 8 zone panels

Installation and user manual for the FX range of fire panels. 1, 2, 4 and 8 zone panels Installation and user manual for the FX range of fire panels 1, 2, 4 and 8 zone panels Contents Panel installation 3 Panel connections 3 Wiring connection drawings 4 Panel facilities 6 Installation check

More information

MGD-32 and AGD-048. Remote Multiplex Graphic Driver Annunciators and Adder Boards. Wiring and Installation Manual

MGD-32 and AGD-048. Remote Multiplex Graphic Driver Annunciators and Adder Boards. Wiring and Installation Manual MGD-32 and AGD-048 Remote Multiplex Graphic Driver Annunciators and Adder Boards Wiring and Installation Manual LT-847 Rev. 8 February 2011 Table of Contents Table of Contents 1.0 Introduction 7 1.1 Contact

More information

FA-1000 SERIES. Microprocessor-Based Fire Alarm Control Panel. Installation and Operation Manual

FA-1000 SERIES. Microprocessor-Based Fire Alarm Control Panel. Installation and Operation Manual FA-1000 SERIES Microprocessor-Based Fire Alarm Control Panel Installation and Operation Manual LT-600 Rev. 19 May 2017 Table of Contents 1.0 Introduction 8 1.1 About this Manual... 8 1.2 About the FA-1000...

More information

Sigma. K1000 Series 1, 2, 4 & 6 Zone Fire Control Panels. Operation and Maintenance Manual. Man-1048 Issue 05 October 2009

Sigma. K1000 Series 1, 2, 4 & 6 Zone Fire Control Panels. Operation and Maintenance Manual. Man-1048 Issue 05 October 2009 Sigma K1000 Series 1, 2, 4 & 6 Zone Fire Control Panels Operation and Maintenance Manual Man-1048 Issue 05 October 2009 CONTENTS Contents... Page Safety & Installation...2 Installation - continued...3

More information

GasScanner 4C. Four Channel Monitor. Operator s Manual. MINT-0280-XX Rev. A 02/25/08

GasScanner 4C. Four Channel Monitor. Operator s Manual. MINT-0280-XX Rev. A 02/25/08 GasScanner 4C Four Channel Monitor Operator s Manual MINT-0280-XX Rev. A 02/25/08 Product Warranty Matheson Tri-Gas., warrants gas alarm equipment sold by us to be free from defects in materials, workmanship,

More information

RAM-3500-LCD. Remote Annunciator. Installation and Operation Manual

RAM-3500-LCD. Remote Annunciator. Installation and Operation Manual RAM-5-LCD Remote Annunciator Installation and Operation Manual LT-9 Rev. July Table of Contents. Introduction 6. Contact Us... 6. Mechanical Installation 8. Mounting Dimensions... 8. Configuring the Main

More information

D350RPL INTELLIGENT PHOTOELECTRONIC DUCT SMOKE DETECTOR WITH EXTENDED AIR SPEED RANGE INSTALLATION AND MAINTENANCE INSTRUCTIONS

D350RPL INTELLIGENT PHOTOELECTRONIC DUCT SMOKE DETECTOR WITH EXTENDED AIR SPEED RANGE INSTALLATION AND MAINTENANCE INSTRUCTIONS D350RPL INTELLIGENT PHOTOELECTRONIC DUCT SMOKE WITH EXTENDED AIR SPEED RANGE INSTALLATION AND MAINTENANCE INSTRUCTIONS Before installing detectors, please thoroughly read the NEMA Guide for Proper Use

More information

GG-2 2-CHANNEL GAS DETECTION CONTROL PANEL. Installation and Operation Manual

GG-2 2-CHANNEL GAS DETECTION CONTROL PANEL. Installation and Operation Manual GG-2 2-CHANNEL GAS DETECTION CONTROL PANEL Installation and Operation Manual 2 GG-2 Warning Use this product only in the manner described in this manual. If the equipment is used in a manner not specified

More information

Long Range Radio Alarm Transmitter

Long Range Radio Alarm Transmitter W A R N I N G Please refer to the System Installation Manual for information on limitations regarding product use and function and information on the limitations as to liability of the manufacturer. TM

More information

Sentry LIQUID LEVEL ALARM MODEL 100 OPERATING MANUAL.

Sentry LIQUID LEVEL ALARM MODEL 100 OPERATING MANUAL. Sentry LIQUID LEVEL ALARM MODEL 100 OPERATING MANUAL www.aquaticsentry.com TABLE OF CONTENTS 1. SAFETY PRECAUTIONS... 3 2. APPLICATION... 3 2.1 HIGH Liquid Level Alarm 2.2 LOW Liquid Level Alarm 3. INSTALLATION...

More information

RANGER 8600 DOWNLOADABLE CONTROL COMMUNICATOR INSTALLATION MANUAL

RANGER 8600 DOWNLOADABLE CONTROL COMMUNICATOR INSTALLATION MANUAL RANGER 8600 DOWNLOADABLE CONTROL COMMUNICATOR INSTALLATION MANUAL TABLE OF CONTENTS GENERAL DESCRIPTION... 2 STANDARD AND OPTIONAL PARTS LIST... 2 PARTS DIAGRAM... 3 TERMINAL DRAWING AND SPECIAL NOTES...

More information

Fire Alarm Control Panel AM2020/AFP1010. Document /22/99 Rev: P/N 15088:J ECN

Fire Alarm Control Panel AM2020/AFP1010. Document /22/99 Rev: P/N 15088:J ECN Fire Alarm Control Panel AM2020/AFP1010 Document 15088 10/22/99 Rev: J P/N 15088:J ECN 99-521 Fire Alarm System Limitations An automatic fire alarm system typically made up of smoke detectors, heat detectors,

More information

AL600ULADA. NAC Power Extender. Installation Guide

AL600ULADA. NAC Power Extender. Installation Guide AL600ULADA NAC Power Extender Installation Guide Rev. 122000 AL600ULADA - NAC Power Extender Overview: The Altronix AL600ULADA is an extremely cost effective 6.5 amp voltage regulated remote power supply/battery

More information

DETECTOR TEST LOG. Detector Identification Information DHX-501 INTELLIGENT AIR DUCT SMOKE DETECTOR HOUSING INSTALLATION AND MAINTENANCE INSTRUCTIONS

DETECTOR TEST LOG. Detector Identification Information DHX-501 INTELLIGENT AIR DUCT SMOKE DETECTOR HOUSING INSTALLATION AND MAINTENANCE INSTRUCTIONS TEST LOG Detector Identification Information Manufacturer and Serial Date Detector Model: Number: Installed: Description of Detector Location: Test Results and Maintenance Data Date Test Test Maintenance

More information

as required for residential sprinklers intended for use in dry pipe systems.

as required for residential sprinklers intended for use in dry pipe systems. Worldwide Contacts www.tyco-fire.com RAPID RESPONSE Residential Dry Pipe System General Description The TYCO RAPID RESPONSE Residential Dry Pipe System provides a normally dry system for areas subject

More information

Cookson Company 1901 South Litchfield Road Goodyear, AZ Phone:

Cookson Company 1901 South Litchfield Road Goodyear, AZ Phone: Cookson Company 1901 South Litchfield Road Goodyear, AZ 85338 Phone: 800-294-4358 www.cooksondoor.com O W N E R S M A N U A L MODEL FIREFLY III EXTENDED PERFORMANCE RELEASE DEVICE TABLE OF CONTENTS INTRODUCTION

More information

M O D E L S FIREGARD BV EXTENDED PERFORMANCE RELEASE DEVICE

M O D E L S FIREGARD BV EXTENDED PERFORMANCE RELEASE DEVICE Cornell 100 Elmwood Ave. Crestwood Industrial Park Mountaintop, PA 18707 tel 800.233.8366 fax 800.526.0841 cornell@cornelliron.com O W N E R S M A N U A L M O D E L S F I R E G A R D B B FIREGARD BV EXTENDED

More information

Installation Instructions

Installation Instructions Installation Instructions S E C U R I T Y S Y S T E M Please refer to the System Installation Manual for information on limitations regarding product use and function and information on the limitations

More information

Model 4001 Series Single Channel Controller

Model 4001 Series Single Channel Controller Model 4001 Series Single Channel Controller Sierra Monitor Corporation 1991 Tarob Court, Milpitas, CA 95035 (408) 262-6611 (800) 727-4377 (408) 262-9042 - Fax E-Mail: sales@sierramonitor.com Web site:

More information

AMC-RAM-4. Refrigerant Alarm Module USER MANUAL. Please read the installation and operating instructions completely and carefully before starting.

AMC-RAM-4. Refrigerant Alarm Module USER MANUAL. Please read the installation and operating instructions completely and carefully before starting. AMC-RAM-4 Refrigerant Alarm Module USER MANUAL IMPORTANT: Please read the installation and operating instructions completely and carefully before starting. Filename: 3310405B, DOC, AMC_RAM4_Manual.doc

More information

www. ElectricalPartManuals. com GADD MKIII Ground Fault Indication System Instruction Manual Ground Fault Protection

www. ElectricalPartManuals. com GADD MKIII Ground Fault Indication System Instruction Manual Ground Fault Protection Ground Fault Protection GADD MKIII Ground Fault Indication System Instruction Manual 7615 Kimbel Street, Mississauga, Ontario Canada L5S 1A8 Tel: (905)673-1553 Fax: (905)673-8472 Toll Free: 1-888-RESISTR

More information

ELECTRIC FIREPLACE HEATER WITH SINGLE GLASS DOOR

ELECTRIC FIREPLACE HEATER WITH SINGLE GLASS DOOR ELECTRIC FIREPLACE HEATER WITH SINGLE GLASS DOOR Model 91797 ASSEMBLY and Operating Instructions Visit our website at: http://www.harborfreight.com Read this material before using this product. Failure

More information

AEGIS FEATURES DESCRIPTION. Conventional Fire Alarm-Suppression Control Unit. Effective: March Programmable Relays

AEGIS FEATURES DESCRIPTION. Conventional Fire Alarm-Suppression Control Unit. Effective: March Programmable Relays AEGIS Conventional Fire Alarm-Suppression Control Unit FEATURES Agency Approvals FM Approved FM Approved to ANSI/UL 864, 9th edition FM Approved to ULC-S527-99 Other domestic U.S. approvals/listings pending/

More information

Multi-Output Access Control Power Supply Charger VDC or 24VDC VDC or 3 24VDC.

Multi-Output Access Control Power Supply Charger VDC or 24VDC VDC or 3 24VDC. M Series Multi-Output Access Control Power Supply Charger Installation Guide Models Include: AL300ULM AL400ULM - 2.5 amp @ 12VDC or 24VDC. - 4 amp @ 12VDC or 3 amp @ 24VDC. AL600ULM AL1012ULM - 6 amp @

More information

UNC100 Integra Manual

UNC100 Integra Manual UNC100 Integra Manual New Generation Building Security July 30, 2014 V1.2 Copyright Notice Copyright 1995-2014 by All rights reserved Worldwide. Printed in Canada. This publication has been provided pursuant

More information

MODEL IFP-100. Installation and Operations Manual. Analog/Addressable Fire Control Panel. Part Number Rev L

MODEL IFP-100. Installation and Operations Manual. Analog/Addressable Fire Control Panel. Part Number Rev L MODEL IFP-100 Analog/Addressable Fire Control Panel Installation and Operations Manual Part Number 151280 Rev L Installation Procedure Adherence to the following will aid in problem-free installation

More information

DH100ACDCLP Air Duct Smoke Detector with Extended Air Speed Range

DH100ACDCLP Air Duct Smoke Detector with Extended Air Speed Range INSTALLATION AND MAINTENANCE INSTRUCTIONS Air Duct Smoke Detector with Extended Air Speed Range A Division of Pittway 825 Ohio Avenue, St. Charles, Illinois 60174 1-800-SENSOR2, FAX: 60-77-6495 The Innovair

More information

Installation Instructions. PS902 Power Supply. These instructions cover the following parts: PS902 Power Supply Specifi cations:

Installation Instructions. PS902 Power Supply. These instructions cover the following parts: PS902 Power Supply Specifi cations: F1! 44487023 These instructions cover the following parts: PS902 Power Supply Installation Instructions! DANGER: To avoid risk of electric shock, turn off AC power before installing or servicing PS902

More information

Control Panel Engineering and Commissioning Instructions

Control Panel Engineering and Commissioning Instructions Twinflex - V3 Fire Detection & Alarm System Control Panel Engineering and Commissioning Instructions (TO BE RETAINED BY THE COMMISSIONING ENGINEER) 26-0338 Issue 9 Fike s policy is one of continual improvement

More information

WARNING. Installation Tip: Try out this unit before installing onto a fire door system. Test and learn the release INTRODUCTION

WARNING. Installation Tip: Try out this unit before installing onto a fire door system. Test and learn the release INTRODUCTION WARNING 1. CAUTION: Review all installation instructions, procedures, cautions and warnings contained within this manual prior to installing and/or servicing this product. As with all releasing device

More information

INTELLIKNIGHT Model 5808

INTELLIKNIGHT Model 5808 INTELLIKNIGHT Model 5808 Addressable Fire Alarm Control Panel Installation and Operations Manual Document: 151274-L8 Rev: X P/N 151274-L8:X ECN: 17-0298 Fire Alarm & Emergency Communication System Limitations

More information

Network Display Unit Installation Instructions

Network Display Unit Installation Instructions Network Display Unit Installation Instructions Introduction This publication describes the installation procedures for the optional Network Display Units (NDUs). This product is compatible with both the

More information

TABLE OF CONTENTS. FOR THE RECORD 15 PROGRAMMING WORK SHEETS 16 CONTROL PANEL WIRING DIAGRAM inside back cover

TABLE OF CONTENTS. FOR THE RECORD 15 PROGRAMMING WORK SHEETS 16 CONTROL PANEL WIRING DIAGRAM inside back cover TABLE OF CONTENTS FEATURES 2 SPECIFICATIONS 2 INSTALLATION 3 Mounting the Panel... 3 Mounting the Keypad... 3 Auxiliary Power Connection... 3 PGM Terminal Connections... 3 Bell/Siren Connection... 3 Keypad

More information

Addressable Fire Alarm Control Panel

Addressable Fire Alarm Control Panel PRODUCT SPECIFICATION XR2400F Addressable FACP Addressable Fire Alarm Control Panel Description The DMP XR2400F Addressable Fire Alarm Control Panel is an expandable Fire Alarm Control with built-in DACT

More information

www. ElectricalPartManuals. com GADP Ground Fault Indication System Instruction Manual Ground Fault Protection

www. ElectricalPartManuals. com GADP Ground Fault Indication System Instruction Manual Ground Fault Protection Ground Fault Protection GADP Ground Fault Indication System Instruction Manual 7615 Kimbel Street, Mississauga, Ontario Canada L5S 1A8 Tel: (905)673-1553 Fax: (905)673-8472 Toll Free: 1-888-RESISTR 737-4787

More information

Beacon 200 Gas Monitor Operator s Manual

Beacon 200 Gas Monitor Operator s Manual Beacon 200 Gas Monitor Operator s Manual Part Number: 71-0059RK Revision: J Released: 1/31/18 www.rkiinstruments.com Product Warranty RKI Instruments, Inc. warrants gas alarm equipment sold by us to be

More information

Pioneer-R16 Gas Monitor Operator s Manual

Pioneer-R16 Gas Monitor Operator s Manual Pioneer-R16 Gas Monitor Operator s Manual Edition 7/2/97 RKI INSTRUMENTS, INC RKI Instruments, Inc. 33248 Central Ave, Union City, CA 94587 (510) 441-5656 Chapter 1: Description About the Pioneer-R16 Gas

More information

RK-05 Carbon Monoxide Detector Operator s Manual

RK-05 Carbon Monoxide Detector Operator s Manual 65-2433RK-05 Carbon Monoxide Detector Operator s Manual Part Number: 71-0189RK Revision: 0 Released: 5/17/11 RKI Instruments, Inc. www.rkiinstruments.com WARNING Read and understand this instruction manual

More information

DESCRIPTIVE AND INSTALLATION INSTRUCTION MANUAL FOR MODEL AH1000, BH1000, AND EH1000 SERIES ANNUNCIATORS

DESCRIPTIVE AND INSTALLATION INSTRUCTION MANUAL FOR MODEL AH1000, BH1000, AND EH1000 SERIES ANNUNCIATORS DESCRIPTIVE AND INSTALLATION INSTRUCTION MANUAL FOR MODEL AH1000, BH1000, AND EH1000 SERIES ANNUNCIATORS SEEKIRK, INC. 2420 Scioto Harper Dr. Columbus, OH 43204 Tel: (614) 278-9200 FAX: (614) 278-9257

More information

RK Transmitter Technical Notice

RK Transmitter Technical Notice 65-2450RK Transmitter Technical Notice Although this Operator s Manual was written for the 65-2400RK combustible gas LEL transmitter, the operational instructions are the same for the 65-2450RK hydrogen

More information

Operation and Maintenance Manual

Operation and Maintenance Manual (FKER Series) Repeater Panel (FKER, FKER, FKER8) Operation and Maintenance Manual Man-9EL Issue June Index Section Page. Introduction.... Safety and mounting.... Technical specification.... Control panel

More information

INSTALLATION AND INSTRUCTION MANUAL

INSTALLATION AND INSTRUCTION MANUAL INSTALLATION AND INSTRUCTION MANUAL SS650-013 013 SIREN LCS652-013 SIREN and Light Controller PLITSTR247 REV. F 12/9/13 NOTICE Due to continuous product improvements, we must reserve the right to change

More information

RC300 IntelliFire Plus Multifunction Remote Control Installation & Operating Instructions

RC300 IntelliFire Plus Multifunction Remote Control Installation & Operating Instructions RC300 IntelliFire Plus Multifunction Remote Control Installation & Operating Instructions Hearth & Home Technologies disclaims any responsibility for, and the warranty will be voided by, the following

More information

FEC403EN Installation Manual

FEC403EN Installation Manual FEC403EN Installation Manual P/N 10-4101-501-2FC1-01 ISS 22JAN15 Copyright Trademarks and patents Manufacturer 2015 UTC Fire & Security. All rights reserved. The FEC403EN name and logo are trademarks of

More information

RK Carbon Monoxide Transmitter Operator s Manual

RK Carbon Monoxide Transmitter Operator s Manual 65-2335RK Carbon Monoxide Transmitter Operator s Manual Part Number: 71-0177RK Revision: 0 Released: 4/12/11 RKI Instruments, Inc. www.rkiinstruments.com WARNING Read and understand this instruction manual

More information

ESL 500N Series Smoke Detector Installation Sheet

ESL 500N Series Smoke Detector Installation Sheet ESL 500N Series Smoke Detector Installation Sheet Additional features Depending on the model, the smoke may also provide the following features. CleanMe: Enables a CleanMe compatible control panel to receive

More information

SHORT CIRCUIT ISOLATOR TO NEXT COMPONENT REQUIRING POWER TO NEXT KEYPAD (** IF REQUIRED) STROBE RELAY MODULE KEYSWITCH ISOLATION MODULE STROBE

SHORT CIRCUIT ISOLATOR TO NEXT COMPONENT REQUIRING POWER TO NEXT KEYPAD (** IF REQUIRED) STROBE RELAY MODULE KEYSWITCH ISOLATION MODULE STROBE The Door Switch 11772 Westline Industrial Drive St. Louis, Mo 63146 (877) 998-5625 www.thedoorswitch.com Patent No. RE42,991 and RE44,039 CONTROL PANEL TRANSFORMER (SUPPLIED WITH CONTROL PANEL) NOTIFICATION

More information