MiNi IP Camera Quick User Manual

Size: px

Start display at page:

Download "MiNi IP Camera Quick User Manual"

Daniela Singleton
6 years ago
Views:

1 MiNi IP Camera Quick User Manual

2 Products Introduction IR Sensor Lens Microphone Speaker Reset MicroSD card Slot DC 5V Power Slot Reset Before starting setup Make sure of the following: - Your router supports the 2.4GHz frequency band (802.11b/g/n). - Your router DHCP is enabled. - Your smartphone is connected to the Internet with a WLAN/Wi-Fi that the camera will connect with. - You know the WLAN/Wi-Fi password.( No special characters in the password and Wi-Fi SSID such - Your smartphone, camera, and router should be within about 8 feet during setup. After your camera is set up,you can move the camera to your preferred location(the configurations are saved to camera system Start setup Step1. ifcam App Installation Go directly to Step3 if the ifcam app is already download and registered in your smartphone. Scan the QR code to download the ifcam App. Search ifcam on Google Play or ios App Store -1-

3 Step2. Register an App user account After download the App ifcam, please Install and register an user account for it. Input a Keep password Forgot Password? Please creat a password for App account please don't input your password Keep password Forgot Password? Step3. Product connection Waiting on App ifcam.. beeping If you can t hear the beeping sound from the device within 1 minute, you need reset the device first. Press RESET button by a reset pin for 10 seconds until you hear a clash sound from the device. Then waiting until you hear continuous beeping sound from the device, and go to Step4 for add the device on App ifcam. -2-

Step4. Add the camera on App Add device Add device Input password(default:888888) Note: The Device ID can be found on the label which is attached to the camera.

4 Step4. Add the camera on App Add device Add device Input password(default:888888) Note: The Device ID can be found on the label which is attached to the camera. Note: Here take camera ID: as an example Add device Add device Add device Device offline,please choose camera network connection mode Smart Wi-Fi AP Hotspot Note:Tap Smart Wi-Fi Your device is offline.please check the device s network connection Step1,Power on the device(ip camera) Step2,Connect the device to network: 1.If device with RJ-45 LAN port, connect device with your router or switch with a net-cable, wait about 30 seconds,tap Back to re-add device; 2.If device without RJ-45 LAN port, tap Smart Wi-Fi Setting to add the device Smart Wi-Fi Setting Your device is offline.please check the device s network connection Step1,Power on the device(ip camera) Step2.1,Wait until you hear continuous beeping sound from the device, tap Next to add the device Step2.2, If didn t hear the continuous beeping sound within 1 minute, reset the device by press the Reset button with a Reset pin for 10 seconds until you hear a clash sound from the device, then wait until hear the beeping sound from the device, tap Next to add the device

Wi-Fi Setting Wi-Fi Setting Wi-Fi Setting Wi-Fi setting succeed salestest Input Wi-Fi Password Skip Change Password Configuring Wi-Fi..., Please wait.

5 Wi-Fi Setting Wi-Fi Setting Wi-Fi Setting Wi-Fi setting succeed salestest Input Wi-Fi Password Skip Change Password Configuring Wi-Fi..., Please wait Change Admin Password Devices List Drop-down to refresh Note: Password should be 3-9 characters long (A-Z,0-9) without special characters. Note: Touch this button for setting APP Authority, Multi-Media, System,Update, Logout, Quit. Authority: Open Audio / Pan Tilt /... Multi-Media: Check Record Playback/ Local Pictures/ Alarm Event

Step5. Live video stream on your smartphone 2.Screenshots Microphone FAQ1: Wi-Fi setting failed Method-1: WiFi setting via MicroSD card 1) Power off the camera. 2) Download WifiInfo.txt from www.

then input this information as picture :FAQ1-1. ifcam ifcam123 4) Copy this WifiInfo.txt file to a empty MircoSD card. 5) Insert the MircoSD card to IP camera and power on the camera.

6 Step5. Live video stream on your smartphone 2.Screenshots Microphone FAQ1: Wi-Fi setting failed Method-1: WiFi setting via MicroSD card 1) Power off the camera. 2) Download WifiInfo.txt from 3) Open the WifiInfo.txt file and input your router's Wi-Fi SSID and password. For example:the router's Wi-Fi SSID is: ifcam and Password is: ifcam123. then input this information as picture :FAQ1-1. ifcam ifcam123 4) Copy this WifiInfo.txt file to a empty MircoSD card. 5) Insert the MircoSD card to IP camera and power on the camera. 6) Wait for 1 min until hear a clash sound from the camera,the clash sound means Wi-Fi settings success. 7) Add the camera to App, Back to user manual Step4 Add the camera on the App. Method-2: WiFi setting via scan QR Code Before Wifi setting, please make sure the camera still on WiFi setting Part..., you can still hear continuous beeping sound from the camera. If can't, you need reset the camera first. ( For reset the camera check user manual Step3 Product connection 3-3) -5-

1) After Wi-Fi setting failed, You will get the following tips: Wi-Fi setting failed Try Again Wi-Fi Setting 404087 Network busy! Please try again.

If you heard continuous beeping sound, check whether input incorrect Wifi password, and try again If this setting failed several times, please try QR Code Setting to configure Wifi QR Code Setting QR

7 1) After Wi-Fi setting failed, You will get the following tips: Wi-Fi setting failed Try Again Wi-Fi Setting Network busy! Please try again. First, please confirm whether the device make beeping sound. If not beeping, you need back to the first step of Add New Device? If you heard continuous beeping sound, check whether input incorrect Wifi password, and try again If this setting failed several times, please try QR Code Setting to configure Wifi QR Code Setting QR Code Setting press Reset button with the Reset pin for 10 seconds untill hear a clash sound from the device,then input Wi-Fi password and tap Next Sricamsales Input Wi-Fi Password Next FAQ1-2 FAQ1-3 2) Click QR Code Setting, and input Wi-Fi password, Click Next. You will get a Wi-Fi QR Code on your smartphone, please direct put the lens of the camera to the QR code within20-30cm and move forward slowly. when you hear a clash sound from the camera, click Next the camera successfully connected to Wi-Fi. QR Code Setting Move camera back and forth slowly scan the QR code above at the distance about 20-30cm, after hear a beeping sound, tap Next Next FAQ1-4 FAQ1-5 Note: When scan the QR code, maybe you need try some different position and angle for scan succeed. -6-

FAQ2: MicroSD card record and playback setting 1) Insert the microsd card to the camera 2) MicroSD card format and record setting Log in ifcam App and follow the steps: Settings -> Record Setting ->

If the SD card recording is full,it will automatically loop coverage, you do not need to manually delete the video file.

8 FAQ2: MicroSD card record and playback setting 1) Insert the microsd card to the camera 2) MicroSD card format and record setting Log in ifcam App and follow the steps: Settings -> Record Setting -> SD card Formatting-> Record Switch (Note: If you use 64G or 128G SD card can't recording, you need to format the SD card to FAT32 format on your PC. If the SD card recording is full,it will automatically loop coverage, you do not need to manually delete the video file.) Devices List Settings Record Setting SD Card Total Space:3784M 1 SD Card Free Space:827M Device information Time Setting Modify Playback Settings Delete SD Card Formatting Record Type Media Setting Security Setting 2 Manual Record Network Setting! Alarm Record Alarm Setting Timing Record Record Setting FAQ2-1 Record Switch FAQ2-2 FAQ2-3 3) Record Playback(on App) Log in ifcam App and follow the steps: Settings >> Playback Tap " Playback" for playback the record on MicroSD card,as picture below (Note: each record is 30 minutes) Devices List Playback-63 Phone local videos SD card videos Latest 1 day 1 Latest 3 days Latest 1 month Lastest 3 months disc1/ _14:00:00_s.av (1123S) disc1/ _13:30:00_s.av (1800S) Modify Playback Settings 2 Delete disc1/ _13:00:00_s.av (1800S) FAQ2-4 FAQ

9 FAQ3: How to Setup Motion Detection Alarm Step1: Enable motion detection alarm Step1-1: Tap Settings button Settings Alarm setting be the alarm setting window as pictures FAQ3-1, FAQ3-2 and FAQ3-3. Devices List Settings 1 Time Setting Media Setting Device information Modify Playback Settings Delete 2 Security Setting Network Setting Alarm Setting FAQ3-1 FAQ3-2 Step1-2: Enable Motion Detection Alarm and Alarm Switch as FAQ3-3! Alarm Setting Receive Notifications Push Notifications Account Alerts Unbound Alerts Save Sender: Please input sender s mail address SMTP server: Select the SMTP server... port: Please input the port number Motion Detect Sensitivity(The most sensitive 0 ) Motion Detection Alarm Buzzer Alarm Alarm Switch Password: Input password Encryption mode No encrypt SSL encrypt TLS encrypt Receiver Input the Input the FAQ3-3 FAQ3-4 Step2: Choose motion detection alarm notification types There are 3 types you can choose to get the alarm notification. Phone push alarm Enable Receive Notifications then the camera will push notification to your smart phone when an alarm is activated. Push notification account is default as the ifcam app login account. If don t need this function, you can delete the push account. Buzzer alarm Enable Buzzer Alarm then the camera s buzzer works when an alarm is activated. Alerts The alarm notification will send to your designated address. Tap " Alerts", and fill in the information as below guide 1. Sender: Please input your address (e.g., Lucy@gmail.com). 2. SMTP server: The server address for the Sender's account. 3. Port: Please select 587 or 465 if the SMTP address is mtp.gmail.com, Smtp.mail.yahoo.com or smtp.live.com(hotmail.com). If not, please select Password: input password 5. Enter up to three receiving accounts (e.g., you may have both Lucy@gmail.com and Marcy@yahoo. com) as picture FAQ3-4 If failed to setup Alert, please activate your Gmail or Yahoo account, Please check FAQS 8 in website -8-

IDoorBell Fon DP68 Quick Installation Guide

IDoorBell Fon DP68 Quick Installation Guide 1. Interface 1. Front Panel 2. Back Panel 2. Doorbell Installation Options and Rain Cover Mounting Note: For the best camera angle, position the camera around