Installation Instructions

Transcription

1 Overview The SIMPLY5 Sensor Connector is used to provide an input for low voltage occupancy sensors and photocells. Use the S5SC with SIMPLY5-compatible lighting fixtures and control devices for fully integrated occupancy and daylight-based lighting control. SIMPLY5 components are plug-and-play devices. They feature automatic detection and configuration for proper operation with other connected SIMPLY5 control devices and lighting fixtures. S5SC Sensor Connectors may be connected at any point in the zone they control. When an occupancy sensor is connected, it will automatically control all zones in the room (all lighting fixtures connected to the SIMPLY 5 Signal Network). When a photocell is connected, it will only control the zone to which it is connected (the local S5JB to which it is connected). Operation The S5SC contains one occupancy sensor input and one photocell input. Occupancy Sensor Input: The S5SC s occupancy sensor input automatically configures to control all lighting fixtures connected in the room, regardless of the number, or location, of all intelligent junction boxes (S5JB) in the space. The S5SC is compatible with the full line of Lithonia Litronic low voltage occupancy sensors. The S5SC s default occupancy sensor function is for manual on / automatic off, but may be configured via the optional S5LEM interface for automatic on / automatic off or automatic on / automatic minimum operation. The S5SC will issue a warning blink 5 minutes prior to turning off the lights. A S5W wall station may be used for manual control and quiet time functionality allowing 1 hour of override to prevent the occupancy sensor from turning off the lights during periods of little movement. To enter Quiet Time mode, press and hold the on/off paddle switch on the S5SW for 3 seconds. The green bargraph LED to the left of the paddle will blink when Quiet Time mode has begun. Photocell Input: The S5SC s photocell input automatically calibrates for daylight-responsive control of the lighting fixtures in the zone to which it is connected. The photocell input only controls the lighting fixtures local to the intelligent junction box (S5JB) zone to which it is connected. 15 WHIP STANDARD FOR S5SC 120 AND S5SC 277 Figure 1 - S5SC 3/08 Page 1

2 Before You Start 1. Always disconnect all power. 2. Install in accordance with the National Electrical Code and any other codes which may apply. 3. Use only as intended and at the listed voltage. 4. All installation and service must be performed by qualified personnel or service technicians. 5. All installation and wiring information contained herein is based on industry-accepted standards and practices. This information is not meant to conflict with or overrule any applicable codes or ordinances. 6. USE EXTREME CAUTION WHEN PERFORMING MAINTENANCE ON THIS EQUIPMENT. Failure to follow any or all warnings and proper safety procedures can cause severe injury or death, and/or damage to the equipment. Mechanical and Electrical Specifications 1. Ambient Conditions: Maximum Ambient Temperature: 104 F/40 C Minimum Ambient Temperature: 32 F/0 C Relative Humidity: 10-90% Non condensing. 2. Power Input: 10-22V, 1.7W max, powered by Simply 5 signal buss. 3. Low voltage power supply: 24VDC, 70 ma maximum, fully regulated, short circuit protected, Class 2 output. 4. Occupancy Sensor Input: Class 2, 0-24VDC; Compatible with all Synergy Litronic brand low voltage occupancy sensors. 5. Photocell Input: Class 2, 0-10VDC; Compatible with DEQ APS series photocell. 6. NEMA 1 enclosure: Mount S5SC using the mounting holes in the rear of the enclosure. 7. A maximum of 3 S5SC(s) can be operated by one intelligent Junction Box (S5JB). Maximum Number of SIMPLY5 Devices: Each S5JB Signal Network can support a maximum of 100 SIMPLY5 devices - S5 Fixtures, S5W wall stations, S5SC sensor connectors or other S5JB(s). When adding occupancy sensors, the total number of possible devices drops based on the number of sensors being added. Refer to the tables below for more information: # of S5 Ballasts, # of LMT, LMTO, LUSO S5W Wall Stations, Occupancy Sensors S5SC Sensor Connectors (32ma each) # of S5 Ballasts, # of LIRO, LIRC S5W Wall Stations, Occupancy Sensors S5SC Sensor Connectors (20ma each) Page 2 3/08

3 Installation HARDWARE Mount Device Mount the S5SC above the ceiling near the photocell or occupancy sensor location, using the mounting holes in the back of the S5SC enclosure. ELECTRICAL Connect Devices The S5SC Sensor Connector is furnished with a Reloc Control Tee for plug and play connection at any point on a SIMPLY5 control zone. The S5SC may also be ordered without the Reloc connector by ordering the HW hardwire option. S5SC Connect the S5SC Reloc Control Tee at the point on the SIMPLY5 zone where control is desired. Connect the occupancy sensor and/or photocell to the S5SC by terminating the conductors from the sensor in the poke-home connector inside the S5SC enclosure. (See Figure 2 For Details) S5SC HW: Select the point on the SIMPLY5 zone where control is desired. Connect the SIMPLY5 signal network conductors to the 2 violet wires inside the S5SC enclosure (they are not polarity sensitive). Connect the occupancy sensor or photocell to the S5SC by terminating the conductors from the sensor in the poke-home connector inside the S5SC enclosure. (See Figure 2 For Details) S5SC CIRCUIT BOARD POKE HOME CONNECTOR RED (+24 VDC) YELLOW (PHOTOCELL) BLUE (OCCUPANCY ) BLACK (DC COMMON) RED YELLOW BLACK PHOTOCELL RED BLACK BLUE OCCUPANCY Figure 2 - S5SC Wiring Terminations 3/08 Page 3

4 The S5SC s photocell input automatically calibrates for daylight-responsive control of the lighting fixtures. Manual calibration is typically NOT required for proper photocell operation. However, for situations where greater control over daylight harvesting operation is desired, an optional Scaling Factor Setup procedure is available. As this Scale Factor setting is lowered, the natural light in the space will have less effect on the artificial light level. As the Scale Factor setting is raised, the natural light in the space will have more effect on the artificial light level. Follow the steps below to set up the Scaling Factor: Calibration 1. Grasp the bottom of the large paddle on the S5SW, and pull out and up gently until you hear a click and the bargraph and amber locator LEDs go off. 2. Press in and hold the paddle switch until the amber locator LED begins flashing once per second, then release it. 3. Press & release the paddle switch once, the amber indicator LED will begin to flash twice per second. 4. Press & release the paddle switch once more, the amber indicator LED will turn steady on. 5. Within the next 10 seconds, you must press and hold the paddle switch until the bargraph LED begins to flash. This should be about 3 seconds. 6. Release the paddle switch after the bargraph LED begins to flash. The lights will flash 3 times indicating Scale Factor Setup Mode is active. The bargraph will indicate the current Scale Value. 7. Use the Raise/Lower button to set the Scale Factor from 1 to Press & release the paddle switch once more to exit Scale Factor Setup Mode. The lights will flash 3 times indicating the system has exited Scale Factor Setup Mode. Note: During this calibration period, you should not try to operate the lights. Additionally, the user has the option to force the photocell into calibration mode. Follow the steps below to force calibration: 1. Grasp the bottom of the large paddle on the S5SW, and pull out and up gently until you hear a click and the bargraph and amber locator LEDs go off. 2. Press in and hold the paddle switch until the amber locator LED begins flashing once per second, then release it. 3. Press & release the paddle switch once, the amber indicator LED will begin to flash twice per second. 4. Press & release the paddle switch once more, the amber indicator LED will turn steady on. 5. Within the next 10 seconds, you must press and hold the paddle switch until the bargraph LED begins to flash. This should be about 3 seconds. 6. Release the paddle switch after the bargraph LED begins to flash. The lights will flash 3 times indicating Scale Factor Setup Mode is active. The bargraph will indicate the current Scale Value. 7. Press and hold the paddle switch until the bargraph LED begins to flash, which should last about 3 seconds. The lights will flash once to indicate calibration mode is active, then the lights will go to full for approximately 30 seconds. While at full, the bargraph LED will blink from bottom to top. After this time interval ends, the lights will go off for 5 seconds. While off, the bottom bargraph LED will blink from top to bottom. The lights will blink once more to indicate the end of calibration mode, and then transition back into Scale Factor Setup Mode. 8. Press & release the paddle switch once more to exit Scale Factor Setup Mode. The lights will flash 3 times indicating the system has exited Scale Factor Setup Mode. Note: During this calibration period, you should not try to operate the lights. Page 4 3/08

5 CONNECT OCCUPANCY S AND PHOTOCELLS AT ANY POINT ON THE ZONE THEY CONTROL BY USING AN S5SC CONNECTOR SYNERGY LITRONIC OCCUPANCY S5SC CONNECTOR TO ADDITIONAL FIXTURES ON THIS ZONE CLASS 2 HARDWIRES INTO S5SC DEQ APS S5 COMPATIBLE FIXTURES S5JB S5SSC S5SC CONNECTOR S5SSC ADD S5W WALLSTATIONS AT ANY POINT ON THE ZONE S5W Figure 3 - SIMPLY5 System Connections Adding S5SC Sensor Connector (Typical) 3/08 Page 5

6 1. The sensors connected to S5SC appear to have no control: The S5SC circuit board contains a status LED which will blink approximately once a second while power is applied. If the sensors connected to S5SC appear to have no effect on the controlled lighting fixtures, remove the cover on the S5SC and verify that the status LED is blinking. If the LED is not blinking, the S5SC is damaged, is not connected to the SIMPLY5 data signal network, or the SIMPLY5 data signal network is not operating correctly. Troubleshooting Contact SIMPLY5 Technical Service at SIMPLY5 Technical Service is available Mon - Fri, from 8:00 a.m. to 5:00 p.m. EST for phone consultation. Visit SIMPLY5 on the internet at for additional information on products, technical data and installation instructions. Warranty SIMPLY5 warrants all equipment to be free from defect in manufacturing, under normal and proper storage, installation, and use. For SIMPLY5 products containing standard Reloc connectors, the warranty is 3 years. For SIMPLY5 products using the hardwire option, the warranty is 1 year. Our guarantee liability extends only to the repair or replacement of the defective part and no labor charges for correction of the defect by repair or replacement will be honored by SIMPLY5 unless prior written authority has been granted by our Customer Service Department. Page 6 3/08