MAX 1500 / MAX Residential/Commercial Brushless DC Slide Gate Operators Made in USA. Quick Install Guide for. Slide Gate Operators

Transcription

1 Quick Install Guide for 500 / 00 Slide Gate Operators CFORMS TO STD 5 CLASS I, II, III, IV CERTIFIED TO CAN/CSA STD C. NO. 47 SENSORS REQUIRED Residential/Commercial Brushless DC Slide Gate Operators Made in USA Version Standard Quick Install Rev 8

2 Table of Contents Quick Install Guide Installation Steps thru Gate ShutOff Switch Gate Tamper Feature Dropping the Chain Gate Tamper is Armed () Dual Gate Operators Wiring Troubleshooting USB Black Box Port Test Entrapment sensor Gate Cycling Troubleshooting Matrix LED Troubleshooting MC00 LED Troubleshooting BC7 Module LED Troubleshooting Commonly Used Safety Sensor Wiring Omron EKR0K4 Omron IRBRET EMX IRBM Single Gate EMX IRBM Dual Gates Miller Gate Link Page / 00 specifications 5 Class of Operation Class I, II, III, IV Gate Type Vehicular Slide Gate Max Gate Length 50 ft Max Gate Weight: lbs Level Gate; 000 lbs Uphill Gate 5 Max lbs Level Gate; 500 lbs Uphill Gate 5 Max Opening Time Selectable speed control ( inch per second) Cycles per Hour AC Power Continuous Battery BackUp Cycles (Batteries fully charged): 500 approximately 00 cycles 00 approximately 00 cycles NOTE: The number of gate cycles using LY battery backup power will vary depending on the weight of the gate, the gate length, the operating condition of the gate, temperature and the amount of charge the batteries have at the beginning of the battery power only operation. Input AC Power/Amps Switchable: 5VAC / 6 Amp, phase or 0VAC / Amp, phase Motor: 500 / HP 4VDC Brushless (6 million cycles) 00 HP 4VDC Brushless (6 million cycles) Chain Size #40 Operating Temperature: 4 F to 58 F (0 C to 70 C) : 5 Type A Inherent ( sensor) Inputs for NORMALLY D (N.C.) 5 Type B (photo cell) and Type B (sensing edge) 7 / / 5 06 Standard Quick Install Rev 8

3 Quick Install Guide For detailed installation instructions and PLETE information about ALL the available options & features for the 500/00/F8, please refer to the 500/00/F8 Installation and Owners manuals. Operator Placement (standard) The gate must be properly installed and work freely in both directions prior to installation of the gate operator. Guide Rollers Outside Property Conduit Area 6.5 Cover Gate Frame Concrete Pad 4 Operator Position on Concrete Pad Photcell to MC00 EDGE Input VRail Conduit Guidelines and Suggestions REQUIRED AC input power wire. REQUIRED Entrapment protection CLOSING photocell and/or sensing edge when not using Gate Link wireless transmitter. Inground loop wires Standard E Entrapment protection sensor MUST installed or operator will NOT function. It MUST be MITORED and NORMALLY D (N.C.). CLOSING cell Beam can be 5 or less away from gate Gate in Closed Position Physical Stop Reflector Inside Property Operator in Front Position (Standard) Note: See manual when mounting operator in REAR Position. Wireless Module CLOSING Sensing with Wireless Module Guide rollers MUST be Installed to keep gate upright. IMPORTANT: Physical stops MUST be installed on BOTH ends of rail to keep gate from traveling off of rail. Secure gate operator to concrete pad with four (4) / x (min) sleeve anchors. 6 above ground to avoid flooding. Input Power / Operator MUST be level. Conduit Run Concrete Pad Check local building codes in your area for depth of concrete before installation. cell Beam Height: Normal 7.5 Max. Concrete Depth Note: The heavier the gate, the deeper the concrete pad should be. At least two feet recommended for heavier gate. Wireless Module IMPORTANT: Physical Stop MUST be installed CLOSING Sensing with Wireless Module 5 06 Standard Quick Install Rev 8

4 connect chain to gate Top View of Operator NOTE: 5 ft of #40 nickel plated chain included. Minimum distance between the drive gear and gate is 4. IMPORTANT: Physical stops MUST be installed on BOTH ends of gate rail to keep gate from traveling off of rail. 4 Min 4 Min Drive Gear YES Chain Bracket NO Operator is too far from gate. Chain is NOT parallel to gate. IMPORTANT: Operator and chain MUST be parallel to gate or the idler wheels could fail. Use the Fine Tune adjustment on the gate bracket connection bolt and make sure the chain runs through the idler wheels without binding on the side chain guides. 4 Min YES NO Back View of Operator Idler Wheel Side Chain Guide Side Chain Guide 4 Min Gate Bracket Fine Tune Adjustment NO Operator is too close to gate. Chain is NOT parallel to gate. NO Operator is NOT parallel to gate. Chain is NOT parallel to gate. YES NO Chain Bracket Idler Wheels Factory installed position Chain brackets MUST remain same height as idler wheels. Chain Bracket NOTE: The chain should sag no more than one () inch per 0 feet of travel. Do not over tighten the chain. NO Chain Bracket DO NOT mount chain bracket too low on gate. Chain Bracket Concrete Pad 6 Operator in Front Position (Standard) Note: See manual when Connecting chain with operator mounted in REAR Position. DO NOT mount chain bracket too high on gate Standard Quick Install Rev 8

5 5V 5V () SEC () PACK 5V ac input power Choose either 5V or 0V setting on input AC power selector switch. Wire desired input AC power wire to power terminal. A additional single gang box is provided to install power outlets if desired. GFCI outlet type is recommended. CAUTI: Make sure circuit breaker is from incoming AC input wire BEFORE wiring! Input AC Power Options CAUTI: If input AC power selector switch is set for 5V but input power is actually 0 V, 7 Amp Fuse will blow. Single Phase 5VAC Only 5VAC Set to 5V 5V 5 OR 0VAC Power Wire Additional Gang Box Additional single gang box provided. Wire GFCI outlet to the input AC wire BEFORE connecting to operator power terminal if power outlets are desired. GFCI Outlet NOT provided IMPORTANT: Make sure there are NO exposed bare wires at the power terminal connection. Line (Black) Neutral (White) Power Terminal Line (Black) Neutral (White) Additional Box AC IN AC Power Box Toroid Box On Off Select Input Voltage 5VAC or 0VAC FUSE 7 Amp Toroid 5 Amp AC Power Gang Box Power Terminal 7 Amp Fuse Input AC Power Selector Switch WARNING! HIGH VOLTAGE disconnect power before servicing unit Single Phase 0VAC Only 0VAC Chassis (Green) Chassis (Green) DANGER HIGH VOLTAGE! Set to 0V 0V Turn Power AC IN Toroid Box On Off Select Input Voltage 5VAC or 0VAC FUSE 7 Amp Toroid 5 Amp Turn Power LEDs should light up on operator. Battery power automatically turns. DO NOT CYCLE OPERATOR! Turn ALL Power Turn Switch on Toroid Box. Battery power will remain. WAIT for 5 seconds. Press and HOLD (approx. 5 seconds) the RED / button until BC7 LEDs turn, then release button. LEDs will turn. (Up to 0 sec.) IMPORTANT: This procedure must be followed whenever ALL power must be turned on operator. MC00 RADIO SIG. RADIO Entrap 4VDC E / F VDC Limit SW MATRIX JOG JOG LINE ID PLUG FIRE DEPT STRIKE KEYPAD / RDR / Replace Battery Battery TEST Battery TIMER POSITI RECORDER OBD PORT BLACK BOX PARTIAL Battery Module PWR IN Error MATRIX D MADE in USA TIME.5Sec Sec ANTI TAIL LED SPEED BACKUP MODE Power In V Motor OverLoad LEFT AUTOMATIC / CTROLS LINE LINE MOTI REVERSE SENSITIVITY OVERLOAD NO / DISABLE IN USE RIGHT ALARM V ALARM RET INPUTS TAMPER EDGE EDGE ID PLUG ERROR ENTRAP MAGLOCK DELAY ALARM MAG LOCK Tamper NO Tamper IN MATRIX BOARD ATTENTI!! HIGH VOLTAGE de'brancher avant l'entretien RS485 RS485 () PWR 4V WARNING! HIGH VOLTAGE disconnect power before servicing unit AC IN On Off FUSE 7 Amp Toroid 5 Amp Select Input Voltage 5VAC or 0VAC L I M I T S E N S O R 5 06 Standard Quick Install Rev 8

6 INPUTS Entrap F PACK ID ALARM LEFT 4 5 () () SEC 4V 4 ground operator Operator MUST be Properly GROUNDED IMPORTANT: Operator MUST be grounded in lightning prone areas or warranty will be VOIDED! WARNING connect chassis to ground rod for lightning protection Proper grounding of this gate operator is a requirement for LIGHTNING PROTECTI in lightning prone areas. To be effective, ground connections should be made with a minimum AWG, 600 volt insulated wire to a ground point within feet of the gate operator. The ground point must be at an electrical panel, a metallic cold water pipe that runs in the earth, or a grounding rod. Ground within ft of operator. Grounding Rod Chassis Ground L IM I T S E N SO R connect chassis to ground rod for lightning protection WARNING WARNING MATRIX Power In BACKUP MODE RIGHT MC00 MAGLOCK DELAY D MADE in USA TIME.5Sec Sec AUTOMATIC / CTROLS ANTI TAIL PLUG TIMER VDC 4VDC PARTIAL RADIO SIG. RADIO POSITI RECORDER OBD PORT BLACK BOX FIRE DEPT MOTI RS485 RS485 () PWR 4V SPEED KEYPAD / RDR STRIKE Limit SW MATRIX JOG JOG LINE MAG LOCK Tamper NO TAMPER Tamper IN MATRIX BOARD E / REVERSE SENSITIVITY OVERLOAD NO / ENTRAP LINE LINE / Battery EDGE EDGE ID PLUG ERROR Replace Battery ALARM V ALARM RET DISABLE LED Battery Module TEST Battery IN Battery Error IN USE Motor OverLoad NOTE: Consult city codes for AC line wiring. Beware of existing underground services. Any of the THREE Chassis Grounds can be used. They are located next to the gear reducer. DO NOT remove any existing green ground wires. 5 set opening direction and id plug LEFT RIGHT LEFT RIGHT Set the desired opening direction. MATRIX MADE in USA ANTI TAIL BACKUP MODE MAGLOCK D DELAY TIME.5Sec Sec AUTOMATIC / CTROLS TAMPER MAG LOCK Tamper NO Tamper IN Dual Gate Operators NOTE: Secondary operator will automatically be set to the opposite opening direction as the primary gate operator. EDGE ID plug MUST be plugged in ID Plug ID Plug F8 F8 ID Plug ID PLUG VDC 4VDC TIMER PARTIAL POSITI RECORDER OBD PORT BLACK BOX MOTI REVERSE SENSITIVITY SPEED OVERLOAD NO / ENTRAP EDGE ID PLUG ERROR ALARM V ALARM RET ID Plug Error: If ID plug is NOT plugged in, board will constantly beep and operator will NOT function. LINE IN USE RADIO SIG. RADIO FIRE DEPT STRIKE KEYPAD / RDR LINE SEC () () DISABLE 4V NOTE: See manual for more information about Matrix settings Standard Quick Install Rev 8 4

7 6 install and adjust limit sensors The limit sensor activators MUST be installed on BOTH ends of chain to indicate the and positions of the gate or DAMAGE will occur. They will activate the corresponding SENSOR (Gray or Black) when they move within range, stopping the gate at the desired positions. Gate Bracket IMPORTANT: LEDs MUST light up when gate reaches and positions or operator WILL NOT learn gate positions. If gate positions are not learned, gate cycling speed will remain slow during normal operation. Back View Plug GRAY Limit Sensor Limit Sensor Activator (Magnet) LED lights when sensing a limit sensor activator (Magnet). Plug Plug BLACK Limit Sensor Limit Sensor Activator installation Gate Bracket IMPORTANT: Limit Sensor Activators MUST be installed on BOTTOM of chain as shown. Factory Installed GRAY Limit Sensor Limit Sensor Activator Operator in Front Position (Standard) Note: See manual when installing limit sensors with operator mounted in REAR Position. Factory Installed BLACK Limit Sensor Limit Sensor Activator Install Limit Sensors: Use JOG Left/Right Buttons on MC00 for installation. JOG gate to position.. Mark magnet position on chain.. JOG gate open slightly and install magnet. 4. JOG gate to position. 5. Mark magnet position on chain. 6. JOG gate closed slightly and install magnet. 7. Gate positions can now be learned AFTER at least E entrapment protection device has been installed (see 7 & 8 ). JOG Left/Right Buttons on MC00 Breather Pin Limit SW MATRIX JOG JOG Entrap LINE MC00 LED Motor OverLoad Push and HOLD the JOG LEFT or JOG RIGHT buttons accordingly to move the gate (release the button to stop gate). CAUTI REMOVE BEFORE OPERATI IMPORTANT: Remove breather pin from gear reducer BEFORE cycling operator Standard Quick Install Rev 8 5

8 7 entrapment protection wiring : LEARNED MITORED / : LEARNED MITORED / EDGE : MITORED LY Typical Wiring For: Normally Closed (N.C.) to EDGE NOTE: Matrix MUST be removed to wire IMPORTANT Sensing devices MUST be powered by MC00 or they will NOT be MITORED. Limit SW MATRIX JOG JOG Entrap LINE MC00 NOTE: See manual for more information about learned monitored inputs. MC00. See pages for specific photocell wiring. INPUTS PACK Power In ALARM Inputs & MUST be LEARNED to MITOR sensors. To LEARN inputs & :. MITORED Sensors MUST be wired to inputs BEFORE they can be learned. Any unused inputs MUST be jumpered.. Reversing and/or can be wired to either input or.. Press and HOLD the & buttons at the same time on Matrix until beep is heard, learn mode begins. MOTI PWR V LY power entrapment protection sensors with MC00 PWR V MC00 Limit SW Entrap Motor Contro ler RS485 RS485 () PWR 4V MC00 PWR V MUST be used Learn mode lasts for 5 min. indicated by beeping. 4. LEDs WILL be for each detected sensor on MC00. LEDs WILL be for BOTH MC00s when dual operators are used. 5. Press button again within 5 min. to learn sensors and end learn mode, beeping stops. Inputs are now MITORED. Reversing OR unused inputs Inputs: MUST jumper MATRIX Sensor Guidelines A sensor MUST be wired to EDGE or operator WILL NOT function. Wire NORMALLY D (N.C.) MATRIX JOG JOG LINE MITORED sensors LY, to each operator s MC00 when dual operators are used. Reversing and/or can Ce l be wired to ANY of the Inputs. MC00 PWR V MUST be used to power MITORED sensors. JUMPERED or fault will occur. UNUSED inputs MUST remain PWR V Polarity does NOT matter LED CAUTI: See installation instructions. ATTENTI: Voir la notice d installation. 4 5 MC00 Slide Motor OverLoad (C) EDGE (N.C.) CLOSING Direction LY Recr Trans Power Power ThruBeam Power Reflective Beam LED Reflector IMPORTANT: cells MUST be in alignment or fault will occur. NOTE: See manual for more information about photcell and sensing edges installation and wiring. Device Locations: CLOSING Direction cell Beam: 5 or LESS from D gate Motor OverLoad Jumper UNUSED Inputs to or a fault will occur. EDGE Typical HARDWiring For: Normally Closed (N.C.) See page 4 to wire a Gate Link wireless transmitter. INPUTS PACK Power In ALARM Sensor Wire Example: Inputs & are NOT used and MUST be jumpered to Standard E Entrapment protection sensor MUST be installed or operator will NOT function. It MUST be MITORED and NORMALLY D (N.C.). Outside Property Sensing Entrapment Area 0K Normally Closed GEM 04 = Obstruction BLINKING = Fault M. PWR INPUT GEM04 MUST be used. PWR V Polarity does NOT matter Inputs & MUST be LEARNED to MITOR sensors. To LEARN inputs & :. MITORED Sensors MUST be wired to inputs BEFORE they can be learned. Any unused inputs MUST be jumpered.. Reversing and/or can be wired to either input or.. Press and HOLD the & buttons at the same time on Matrix until beep is heard, learn mode begins. MOTI Sensing to EDGE (CLOSING Direction LY) PWR V LY power entrapment protection sensors with MC00 PWR V MC00 Motor Contro ler PWR 4V RS485 () RS485 MC00 PWR V MUST be used Learn mode lasts for 5 min. indicated by beeping. 4. LEDs WILL be for each detected sensor on MC00. LEDs WILL be for BOTH MC00s when dual operators are used. 5. Press button again within 5 min. to learn sensors and end learn mode, beeping stops. Inputs are now MITORED. Reversing OR unused inputs Inputs: MUST jumper MATRIX Sensor Guidelines A sensor MUST be wired to EDGE or operator WILL NOT function. Wire NORMALLY D (N.C.) Limit SW MATRIX JOG JOG Entrap LINE MITORED sensors LY, to each operator s MC00 when dual operators are used. Reversing and/or can Ce l be wired to ANY of the Inputs. MC00 PWR V MUST be used to power MITORED sensors. JUMPERED or fault will occur. UNUSED inputs MUST remain LED CAUTI: See installation instructions. ATTENTI: Voir la notice d installation. 4 5 MC00 Slide Motor OverLoad (C) EDGE (N.C.) CLOSING Direction LY CLOSING direction photocell to MC00 EDGE input. Run conduit to operator Wall Gate Closed IMPORTANT: Entrapment Protection cells MUST be Normally Closed Type. NOTE: input on Matrix is NOT MITORED (Normally ) and is NOT 5 entrapment protection. IMPORTANT: cells MUST be in alignment or fault will occur. Inside Property Continued on next page Standard Quick Install Rev 8

9 7 continued Device Locations: cell Beam Height Install photocells on either side of gate, as close as practical to the gate but no further away than 5. 5 or Less 5 or Less ING Direction cell Outside Property IMPORTANT: Entrapment Protection cells MUST be Normally Closed Type. Beam Height: for most installations but No higher than 7.5 above ground. Wall Gate Inside Property Outside Property Gate Closed Wall Illustrations not to scale Inside Property Sensing s Beam: 5 or LESS from gate. Run conduit to operator Entrapment Area ING direction photocell to MC00 motor controller,. Normally D (N.C.) NOTE: Connect to input on MC00. Beam IMPORTANT: cells MUST be in alignment or fault will occur. ING direction 0K NORMALLY D Sensing Wall CLOSING direction 0K NORMALLY D Sensing Wirelessly Wireless Module Wireless Module Gate Closed Wireless Module ING direction0k NORMALLY D Sensing Wirelessly IMPORTANT: Sensing edges MUST be 0K Normally Closed Type. Wall Wireless Module WIRELESS NOTE: Refer to the instruction sheet that comes with the wireless module for wiring and mounting instructions when using wireless option. ING direction Sensing SelfSupporting Post CLOSING direction Sensing CLOSING direction Sensing Gate Closed Wireless Module ING direction Sensing ING direction Sensing MGLTX0 Gate Link Miller ING direction Sensing (Wireless) If a selfsupporting post is being used, then sensing edges need to be installed on EACH side of the post to protect against entrapment in the ING and CLOSING direction of gate travel Standard Quick Install Rev 8 7

10 8 learn gate positions After the limit sensor activators and at least E entrapment sensor has been installed, put the gate in the D position: Gate ShutOff Switch IMPORTANT: SHUT Switch MUST be. (see page for more information about switch). Push button to cycle gate to open position. Operator cycles slowly while learning position.. Then push button to cycle gate to closed position. Operator cycles slowly while learning position. MOTI MOTI Matrix Matrix SPEED Matrix After gate positions have been learned, the gate will cycle at the speed set on matrix SPEED setting. Set to 9 Adjust Reverse sensor The Sensor Electronic Reversing Device (Type A) MUST be adjusted for the and gate cycles. When the gate encounters an obstruction during the cycle, it will reverse to the open position and PAUSE the gate. An input command (press remote button or exit loop) is needed BEFORE the gate will reset and close again. When the gate encounters an obstruction during the cycle, it will reverse approximately 6 inches and PAUSE the gate. An input command (press remote button or exit loop) is needed BEFORE the gate will reset and open again. For the to function correctly: Limit sensors must be learned BEFORE adjusting the. Limit SW MATRIX JOG JOG Entrap LINE MC00 LED Motor OverLoad 6 sensitivity setting positions. NO mechanical hard stop for knob. Typical Settings: LED LED Position : Typical gate setting. Position 6: Heavy gate setting. Long gate setting. Cantilever gate setting. Uphill gate setting. High wind area gate setting. IMPORTANT: When satisfied with adjustment, cycle the gate or 4 times to make sure that the sensor does not falsely trigger during normal gate operation. Readjust if this happens. CAUTI: Position 6 results in gate exerting IMUM force before reversing direction. LED LED Adjusting : If alarm sounds while adjusting, press BUTT on Matrix to shutoff alarm. A. Turn knob until blue LED lights up. Maximum sensitivity reached, Position Too sensitive for most gates. B. Turn knob counterclockwise to reduce gate sensitivity while testing until desired results is attained. (LED remains for all but position ) Matrix MOTI 5 06 Standard Quick Install Rev 8 8

11 0 loops & loop detectors InGround Loops Connections Exit Loop Safety Loop NOTE: See manual for more information about loops and loop detectors. Safety Loop Safety Loops Wired in series ID PLUG MATRIX VDC 4VDC MADE in USA RADIO SIG. RADIO ANTI TAIL TIMER BACKUP MODE POSITI RECORDER MAGLOCK DELAY TIME.5Sec Sec AUTOMATIC / CTROLS FIRE DEPT D PARTIAL OBD PORT BLACK BOX STRIKE KEYPAD / RDR MOTI REVERSE SENSITIVITY SPEED OVERLOAD NO / LINE LINE SEC () () TAMPER ENTRAP DISABLE MAG LOCK Tamper NO Tamper IN EDGE EDGE ID PLUG ERROR ALARM V ALARM RET 4V IN USE EDI Tel: DEFLECTOMETER 5 = Optimum Sens. = Low = Increase Sens. = MediumLow = Decrease Sens. = MediumHigh = = Fail Secure = Normal Power = Fail Safe = No Power = Pulse on Entry = Detect = B same as A = No Detect LED INDICATORS DETECT Hz Flash=Delay Timing Loop Fault Flash = Open Loop Flashes= Shorted Loop Flashes=5% change of Inductance Both LED s Flashing= Current Loop Fault PWR LED Flashing= Previous Loop Fault SW SW Frequency SW SW4 SW5 Output B = Pulse on Exit = Loop Fault = Second Delay = No Delay = Normal Presence = Infinite Presence SW6 SW7 SW8 External Loop Detector = Boost = No Boost External Loop Detectors LMA800 SENS DEFLECTOMETER SENS DETECT EDI OPTIS Power Terminal Wire to back of detector PlugIn Loop Detectors Power Terminal Com, Gnd (Black) Loop Detect Output (White) Power 5 VDC (Red) External Loop Detector Cable Adapter Sold separately NOTE: DO NOT select the PSED output option for Loop Detectors. NOTE: DO NOT set Loop Detectors to HIGH sensitivity to avoid false trigger. matrix settings Battery BackUp Mode After a power failure and battery power is drained, the next open command, gate will remain. Gate will automatically close after AC power is restored. D After a power failure and battery power is drained, gate will remain D. See manual for more information about opening a D gate during a power failure (emergency open device, manual open, etc). TIME After a power failure, gate automatically S and REMAINS, even after power is restored. A close command or loop event is needed to close gate. Anti Tailgate Set to See manual before enabling this feature. Close Timer st click clockwise Knob at position: / sec... nd click clockwise: sec... rd click: 4 sec... 4th click: 8 sec... etc up to 60 sec.. See manual for more info. ID PLUG MATRIX VDC 4VDC MADE in USA RADIO SIG. RADIO BACKUP MODE ANTI TAIL TIMER POSITI RECORDER MAGLOCK DELAY TIME.5Sec Sec AUTOMATIC / CTROLS FIRE DEPT D PARTIAL OBD PORT BLACK BOX STRIKE KEYPAD / RDR MOTI REVERSE SENSITIVITY SPEED OVERLOAD NO / LINE LINE SEC () () TAMPER ENTRAP DISABLE MAG LOCK Tamper NO Tamper IN EDGE EDGE ID PLUG ERROR ALARM V ALARM RET 4V IN USE Maglock Delay Set to See manual before enabling this feature. Gate Speed Set to See manual for more info Standard Quick Install Rev 8

12 wiring opening device options MATRIX MADE in USA BACKUP MODE D MAGLOCK DELAY TIME.5Sec Sec AUTOMATIC / CTROLS MAG LOCK Pos Neg + Maglock 50 ma Max. VDC OR 4 VDC Radio Power ID PLUG VDC 4VDC RADIO SIG. RADIO ANTI TAIL TIMER FIRE DEPT PARTIAL POSITI RECORDER OBD PORT BLACK BOX STRIKE KEYPAD / RDR MOTI REVERSE SENSITIVITY SPEED OVERLOAD NO / LINE LINE SEC () () TAMPER ENTRAP DISABLE Tamper NO Tamper IN EDGE EDGE ID PLUG ERROR ALARM V ALARM RET 4V IN USE Pos Neg + Maglock Power maglock option Maglock MUST be connected as shown when used. MAGLOCK DELAY.5Sec Sec MAG LOCK Wire Radio 4Wire Radio MAGLOCK DELAY: You MUST select a time delay when using a maglock. Maglock power disengages.5 sec or sec before gate starts opening. MAGLOCK LED (Monitors Maglock): Locked Unlocked Flashing Problem with Maglock Power. Dual Gate Operators using Maglock: Primary gate opens FIRST. Install maglock accordingly to account for this. Normal Opening Devices Emergency Open Device Emergency (Overrides gate disable switch) NOTE: See manual for more info. (N.O.) Dry Contact (N.O.) Normal Opening Devices Key Switch Card Reader Keypad External Alarm Reset Button Security Device Com Stop PRESS to Telephone Entry Dry Contact (N.O.) Separate power for Devices if required Standard Quick Install Rev 8 0

13 gate shutoff switch Turn this feature while servicing the gate operator. This switch disables all / devices BUT the JOG LEFT/RIGHT buttons on MC00 so gate can not accidentally get activated while operator is being serviced. IMPORTANT: When the Gate ShutOff switch is turned, any / command given to gate operator will just BEEP for a few seconds and ignore command. Gate ShutOff Switch Only the Jog Left or Jog Right buttons will operate gate when Gate ShutOff switch is turned. Entrap MC00 Limit SW MC00 motor controller MATRIX JOG JOG LINE LED Motor OverLoad TECHNICIAN MAINTENAE TIP: One wire can be unplugged from the back of the Gate ShutOff switch after servicing the operator to prevent the switch from accidentally being turned during normal operation. Plug the wire back in and turn the switch only while servicing the operator. This can prevent an unnecessary service call by a technician when the only thing wrong with a malfunctioning operator is the Gate ShutOff switch has accidentally been turned but the owner is unaware of this Standard Quick Install Rev 8

14 VDC 4VDC MADE in USA LEFT RIGHT LINE () REVERSE SENSITIVITY OVERLOAD ().5Sec ENTRAP gate tamper feature Many different safety devices can be wired to the TAMPER. After device is wired to relay, it MUST be ARMED to function. Wiring Gate Tamper The TAMPER can be used for various functions such as turning a warning light, siren or camera on when the gate is tampered with (Vandalized Gate). The gate operator defines a Vandalized Gate as UNAUTHORIZED movement of the gate. This can occur if the chain is dropped and gate is manually moved from the closed position or the gate is forced open from the closed position without authorization. Existing Building Alarm System TAMPER NO/Com Relay: Connect a warning light, siren, camera or an existing alarm system to relay. TAMPER IN/ Input: Connect a sensor device to input. When Tamper In/ gets triggered, device that is wired to Tamper relay (NO/Com) will activate. Siren Power TAMPER Warning Light Power Tamper NO Tamper IN Motion Sensor Security Camera ID PLUG MATRIX RADIO SIG. RADIO ANTI TAIL BACKUP MODE MAGLOCK D DELAY TIME Sec AUTOMATIC / CTROLS TIMER PARTIAL FIRE DEPT POSITI RECORDER OBD PORT BLACK BOX STRIKE KEYPAD / RDR SPEED MOTI LINE SEC NO / TAMPER DISABLE MAG LOCK EDGE EDGE ID PLUG ERROR ALARM V ALARM RET 4V Tamper NO Tamper IN IN USE Arm Gate Tamper (Turn ) The TAMPER is factory set to (Unarmed). It MUST be turned (Armed) or safety device connected to the TAMPER relay will NOT activate. Press and HOLD the button while simultaneously pressing the POSITI RECORDER button. Hold BOTH buttons down until Gate Tamper LEDs light up then turn and a beep is heard. Gate Tamper is now ARMED (). NOTE: DO NOT press the POSITI RECORDER button before the button or Gate Tamper will NOT Arm. To UNARM (Turn ) Gate Tamper repeat above step. When TAMPER is triggered, the OPERATOR ALARM and TAMPER relay will activate. The operator will shut down all operating functions. The alarm reset button MUST be pressed to turn the alarm and reset the operator. If TAMPER is armed and relay is connected to an existing building alarm system, then they will get a triggering of their alarm system and should be notified of the situation. Alarm Reset Button ID PLUG MATRIX VDC 4VDC MADE in USA RADIO SIG. RADIO ANTI TAIL TIMER BACKUP MODE MAGLOCK DELAY TIME.5Sec Sec AUTOMATIC / CTROLS D PARTIAL POSITI RECORDER FIRE DEPT OBD PORT BLACK BOX STRIKE KEYPAD / RDR MOTI REVERSE SENSITIVITY SPEED OVERLOAD NO / Press Together LINE LINE SEC () () TAMPER ENTRAP DISABLE MAG LOCK Tamper NO Tamper IN EDGE EDGE ID PLUG ERROR ALARM V ALARM RET 4V IN USE Gate Tamper LEDs 5 06 Standard Quick Install Rev 8

15 Dropping the Chain TAMPER is ARMED () The TAMPER is factory set to (Unarmed). See previous page for more information about ARG TAMPER. If an existing alarm system (Building alarm system) is connected to the TAMPER relay (see previous page), notify proper authorities BEFORE dropping the chain. MATRIX MADE in USA ANTI TAIL BACKUP MODE MAGLOCK DELAY TIME.5Sec Sec AUTOMATIC / CTROLS D TAMPER MAG LOCK Tamper NO Tamper IN Gate Tamper Relay Gate ShutOff Switch Alarm Reset Button ID PLUG VDC 4VDC TIMER PARTIAL POSITI RECORDER OBD PORT BLACK BOX SPEED RADIO SIG. RADIO FIRE DEPT STRIKE KEYPAD / RDR MOTI () LINE REVERSE SENSITIVITY OVERLOAD NO / LINE SEC () ENTRAP DISABLE ALARM V ALARM RET 4V EDGE EDGE ID PLUG ERROR IN USE PROPER Dropping of Chain while TAMPER is ARMED:. Turn Gate ShutOff switch to disable operator alarm.. Drop the Chain.. TAMPER relay WILL be activated. 4. Service operator. 5. Reconnect the chain to gate. 6. Turn Gate ShutOff switch. Gate ShutOff Gate ShutOff 7. Rearm an alarm system that may be connected to the TAMPER relay. IMPROPER Dropping of Chain (Vandalize): Gate ShutOff switch is NOT turned. When the chain is improperly dropped (Vandalized), the OPERATOR ALARM and TAMPER relay will activate. The operator will shut down all operating functions. The alarm reset button MUST be pressed to turn the alarm and reset the operator. If TAMPER relay is connected to an existing building alarm system, then they will get a triggering of their alarm system and should be notified of the situation Standard Quick Install Rev 8

16 dual gate operators wiring Reflector To MC00 EDGE Input Sensing s AC input power To Secondary MC00 or Input To Primary MC00 or Input AC input power Secondary Operator NO Matrix Three RS485 Wires to Matrix (See below) NOTE: See manual for more information about Dual Gate Operator installation. Primary Operator Matrix MC00 Entrap Secondary Operator MC00 Learn mode lasts for 5 min. indicated by beeping. 4. LEDs WILL be for each detected sensor on MC00. LEDs WILL be for BOTH MC00s when dual operators are used. 5. Press button again within 5 min. to learn sensors and end learn mode, beeping stops. Inputs are now MITORED. Inputs: MUST jumper unused inputs Limit SW MATRIX JOG JOG LINE Inputs & MUST be LEARNED to MITOR sensors. To LEARN inputs & :. MITORED Sensors MUST be wired to inputs BEFORE they can be learned. Any unused inputs MUST be jumpered.. Reversing and/or Ce l can be wired to either input or.. Press and HOLD the & buttons at the same time on Matrix until beep is heard, learn mode begins. MOTI LED Power In ALARM Reversing OR CAUTI: See installation instructions. ATTENTI: Voir la notice d installation Motor OverLoad ID PLUG MATRIX VDC 4VDC MADE in USA RADIO SIG. RADIO Matrix Primary Operator ANTI TAIL TIMER BACKUP MODE POSITI RECORDER MAGLOCK DELAY TIME.5Sec Sec AUTOMATIC / CTROLS FIRE DEPT Matrix Open Left Open Right set for the OPERATOR opening direction. (Secondary operator automatically set to opposite opening direction) OPTIAL Inground loop wires to the OPERATOR. D PARTIAL OBD PORT BLACK BOX STRIKE KEYPAD / RDR MOTI REVERSE SENSITIVITY SPEED OVERLOAD NO / LINE LINE SEC Jumper ALL Entrapment Protection Inputs to on Secondary MC00 when LY using RS485 to RS485 photocell. RS485 () to RS485 () RS485 to RS485 AC input power to EACH gate operator. Entrapment protection ( photocell) to OPERATOR MC00. Jumper any UNUSED entrapment protection inputs to on BOTH MC00s or a fault will occur. See manual if installing more entrapment protection devices than just a photocell. Opening device to the OPERATOR. INPUTS PACK LY power entrapment protection sensors with MC00 PWR V MC00 PWR V MUST be used operator WILL NOT function. MITORED sensors LY, to each operator s MC00 when dual operators are used. Sensor Guidelines A sensor MUST be wired to EDGE or Wire NORMALLY D (N.C.) Reversing and/or can be wired to ANY of the Inputs. MC00 PWR V MUST be used to power MITORED sensors. UNUSED inputs MUST remain JUMPERED or fault will occur. MC00 Slide PWR V MATRIX RS485 RS485 () PWR 4V () () TAMPER ENTRAP DISABLE SEC MAG LOCK MOTI Tamper NO Tamper IN EDGE EDGE ID PLUG ERROR ALARM V ALARM RET 4V IN USE Alarm Shut NOTE: The Alarm ShutOff is located on the Primary gate operator LY. There is NO alarm shutoff button on the secondary gate operator. Matrix Button 5 06 Standard Quick Install Rev 8 4

17 Troubleshooting This page and the next 5 pages can help troubleshoot problems that might occur after installation is complete. usb black box port 700FS Download a simple.txt file to troubleshoot gate operator errors and view event history. ID PLUG MATRIX ANTI TAIL TIMER BACKUP MODE POSITI RECORDER SPEED AUTOMATIC / CTROLS MAGLOCK DELAY D MADE in USA TIME.5Sec Sec VDC 4VDC RADIO SIG. RADIO Matrix FIRE DEPT PARTIAL OBD PORT BLACK BOX STRIKE KEYPAD / RDR MOTI () LINE LINE REVERSE SENSITIVITY OVERLOAD NO / SEC () TAMPER ENTRAP DISABLE MAG LOCK ALARM V ALARM RET 4V Tamper NO Tamper IN EDGE EDGE ID PLUG ERROR IN USE Flash Drive obd port obd port USB Phone Adapter Required OR Smart Phone Computer Event History Text Document Sample Event type clarifica on: INFO: informa onal message only WARNING: unusual event but doesn't cause system malfunc on ERROR: abnormal event, could cause system malfunc on ENTRAP: entrapment detec on event Event Report: Fri 07//04 0:59:4 INFO : Cycle Counter Fri 07//04 0:59:4 ENTRAP : SEC_MC: First Detected Fri 07//04 0:59:7 INFO : Radio Input Deac vated Fri 07//04 0:59:6 INFO : Radio Input Ac vated Fri 07//04 0:58:54 INFO : PRI_MC: Fully Open Posi on Learned Fri 07//04 0:58:5 INFO : SEC_MC: Fully Open Posi on Learned Fri 07//04 0:57:40 INFO : PRI_CIO: Communica on Established Fri 07//04 0:57:8 ENTRAP : PRI_MC: Deac vated Fri 07//04 0:57:4 ENTRAP : PRI_MC: Ac vated Fri 07//04 0:57: INFO : Radio Input Deac vated Fri 07//04 0:57: INFO : Radio Input Ac vated Fri 07//04 0:56:46 WARNING: PRI_MC: Tamper Reported Fri 07//04 0:56:6 INFO : SEC_MC: Fully Open Posi on Unknown Fri 07//04 0:56:6 INFO : PRI_MC: Fully Open Posi on Unknown Fri 07//04 0:56:6 WARNING: PRI_MC: Tamper Reported Fri 07//04 0:56: ENTRAP : PRI_MC: Deac vated Fri 07//04 0:56: ENTRAP : PRI_MC: Ac vated Fri 07//04 0:56: ENTRAP : PRI_MC: Deac vated Fri 07//04 0:56: ENTRAP : PRI_MC: Ac vated. Plug USB flash drive into OBD port of Matrix. OBD LED will flash while file is downloading. Remove flash drive after LED stops flashing.. Plug flash drive into any computer USB port OR smart phone using a USB phone adapter. The most recent 000 events can be viewed. No special software required. test edge entrapment sensor Troubleshoot EDGE entrapment protection sensor.. Press and HOLD the button while simultaneously pressing the button. Hold BOTH buttons down until beeping is heard, learn mode begins. NOTE: DO NOT press the button before the button or learn mode will NOT begin. MOTI Matrix. EDGE LED should be MC00 if an entrapment sensor is detected. If EDGE LED is NOT on, wiring to photocell is bad, photocell is out of alignment, photocell is wired wrong, photocell is bad, or sensor is NOT normally closed (N.C.), etc. Entrap MC00 Limit SW Jumpers e MATRIX JOG JOG LINE LED Motor OverLoad. Press button again within 5 min. to end learn mode, beeping stops. NOTE: If button is not pressed within 5 min. learn mode automatically end after 5 min. MOTI Matrix Sensor Wire 5 06 Standard Quick Install Rev 8 5

18 gate cycling troubleshooting Use this table to help with troubleshooting AND operator LED troubleshooting on the next 4 pages. Refer to 500/00/F8 installation owner manuals for more information. Gate Symptom Gate beeps but will not open or close for any command given. Gate moves slowly. Gate beeps when opening and closing. Gate does NOT open. Gate does NOT close. Gate stops prematurely and beeps, moves in opposite direction. Gate will stop before reaching desired limit setting. Gate stops abruptly while in motion. Gate reopens while closing. Gate does not learn new magnet positions. Solutions (what to check) Check SHUT switch, it should be. Turn switch then again, possible chain drop event and switch needs to be recycled. DISABLE LED should be. Check if and Limits have been learned. Refer to Learn Gate Positions section and learn limits. Check if SPEED rotary dial is set to position (LED on). Gate may be too heavy for operator (check manual for maximum gate weight for your model operator). Check if " IN USE" LED is. If so, gate is on Battery back up mode and battery is running low. Operator may be in battery back up mode. check if Mode switch is on the back of Matrix. Check if Gate in Motion Alarm feature is ( Mode 0 switch is on back of Matrix and set to ). Check if Power LEDs are on both Matrix and MC00. Check if LINE LED and LINE LED are both on Matrix. Check if "open RIGHT / open LEFT" switch is set properly. Check if SHUT switch is ( DISABLE LED should be ) Check if DISABLE LED is. If so, check if DISABLE input is active. Check if "EDGE " LED or "" LED is or BLINKING on MC00. If so, check entrapment sensor wiring or missing jumper. Check if IN USE LED is. IF so, battery may be too low and gate is kept closed ( BACKUP MODE switch set to Leave Closed ). Check if Power LEDs are on both Matrix and MC00. Check if LINE LED and LINE LED are both on Matrix. Check if EDGE LED is or BLINKING on MC00. If so, check entrapment sensor wiring and alignment. Check if any loops are active, check LOOP or LOOP LED is. Check if any open command inputs are active (check if LED is on the matrix for: RADIO, FIRE DEPT,, STRIKE, KEYPAD/RDR, ). Check device connected to the input that LED light is turned. Check if open RIGHT / open LEFT switch is set properly. Check if SHUT switch is ( DISABLE LED should be ) Check if DISABLE LED is. If so, check if DISABLE input is active. If EDGE LED or LED is or BLINKING on MC00. If so, check entrapment sensor wiring or missing jumper. If IN USE LED is and BACKUP MODE switch = Leave Open, then battery may be too low and gate is kept. If IN USE LED is and BACKUP MODE switch is set to TIME, then if AC power is lost, gate will automatically open time. If TIMER is, then gate will not close automatically. A close command (i.e radio, close) is required to close gate. Loop detector is defective (, or ). Loop has a short or open. Measure loop resistance. If LED is, an obstruction ( event) is detected. If no apparent obstruction, select a less sensitive setting. If EDGE LED is, entrapment sensor is triggered or jumper on connector is broken. Gate Open and Close Limits have not been learned properly. Relearn limit positions using jog RT and jog LT. The magnet(s) are not installed in correct limit position on the chain. Only for ING gate (not during closing cycle): Check if PARTIAL feature is turned. Relearn partial open position or turn off PARTIAL feature. If MATRIX LINE LED or LINE LED are on MC00, then check wiring between (MC00 & Matrix ) or (MC00 and Limit switch box). Check if LED is on MC00. If so, check entrapment sensor wiring or missing jumper Motor hall sensor cable may be compromised. Unplug cable from MC00 Motor Inputs and ensure wires are not broken and are crimped properly. Check if closing photo cell is misaligned with reflector (check photocell on MC00 EDGE input or Matrix cell input. Check if LOOP is set too sensitive, then gate itself triggers loop and reopens gate. Desensitize LOOP detector. Use jog LEFT/RIGHT buttons to learn new positions instead of using open or close buttons on Matrix Standard Quick Install Rev 8 6

19 matrix led troubleshooting. LOOP. LOOP. LOOP ID plug MUST be plugged in F8 4. VDC 5. 4 VDC F8 ID PLUG MATRIX VDC 4VDC MADE in USA RADIO SIG. RADIO BACKUP MODE ANTI TAIL TIMER POSITI RECORDER MAGLOCK DELAY TIME.5Sec Sec AUTOMATIC / CTROLS FIRE DEPT D PARTIAL OBD PORT BLACK BOX STRIKE KEYPAD / RDR MOTI REVERSE SENSITIVITY SPEED OVERLOAD NO / LINE LINE SEC () () TAMPER ENTRAP DISABLE MAG LOCK Tamper NO Tamper IN EDGE EDGE ID PLUG ERROR ALARM V ALARM RET 4V IN USE 0. MAGLOCK. TAMPER.. EDGE 4. EDGE 5. ID PLUG ERROR 6. ENTRAPMENT 7. REVERSE SENSITIVITY 8. OVERLOAD 9. NO 0. IN USE.. DISABLE Matrix LED Problem Condition ID PLUG LED is FLASHING on Matrix and board beeping LED is IN USE LED is IN USE and LED are FLASHING LINE LED is SECDARY LINE LED is LINE LED is SECDARY LINE LED is Entrap LED is REVERSE SENSITIVITY LED is FLASHING EDGE LED is EDGE LED is flashing EDGE LED is EDGE LED is FLASHING 6. SECDARY LINE 7. LINE Normal LED 5 0 / 0 / Table continued on next page 8. SECDARY LINE 9. LINE Solution(s) for Problem Condition Insert ID PLUG module that is tethered to chassis into ID PLUG connector of Matrix. Check if AC / is. Check 4 V wiring from MC00. AC power is lost, operator is in battery backup mode. Check if AC / is. Measure power input DC voltage on Matrix ( 4V/ pin black connector), (expected reading 4 VDC if AC on, 5VDC if on battery backup). Battery not plugged in to IN port on battery charger (BC7 module) Check wiring between Matrix RS485 (+,, gnd) and MC00 RS485 (+,, gnd) terminals, connect [ to ], [() to ()] and [ to ] Check wiring between Matrix RS485 (+,, gnd) and SECDARY MC00 RS485 (+,, gnd) terminals, connect [ to ], [() to ()] and [ to ]. Check if limit switch box is plugged into MC00 input on back and MC00 is powered. Check if limit switch box is plugged into SECDARY MC00 input on back and MC00 is powered. An entrapment event has occurred, check if an entrapment sensor was triggered (see if EDGE, EDGE, or LED is on). An event may have occurred. Check for gate obstruction. sensitivity is too high for application. Readjust setting on MC00, (see 9 ). Sensor on EDGE input (photocell or edge) may have detected an obstruction while closing gate. cell on EDGE input is misaligned with reflector. Sensor on EDGE input (photocell or edge) may not be wired properly, (see 7 ). Sensor is NOT a N.C. monitored sensor that is 5 06 compliant. Sensor is damaged or malfunctioning. Sensor might need to be relearned. Jumper between EDGE and is missing or broken (jumper is required if a sensor is not present). Sensor on EDGE input (photocell or edge) may have detected an obstruction while opening or closing gate. cell on EDGE input is misaligned with reflector. Sensor on EDGE input (photocell or edge) may not be wired properly, (see 7 ). Sensor is NOT a N.C. monitored sensor that is 5 06 compliant. Sensor on EDGE is damaged or malfunctioning. Sensor might need to be relearned Standard Quick Install Rev 8

20 matrix led continued. LOOP. LOOP. LOOP ID plug MUST be plugged in F8 4. VDC 5. 4 VDC F8 ID PLUG MATRIX VDC 4VDC MADE in USA RADIO SIG. RADIO BACKUP MODE ANTI TAIL TIMER POSITI RECORDER MAGLOCK DELAY TIME.5Sec Sec AUTOMATIC / CTROLS FIRE DEPT D PARTIAL OBD PORT BLACK BOX STRIKE KEYPAD / RDR MOTI REVERSE SENSITIVITY SPEED OVERLOAD NO / LINE SEC () LINE () TAMPER ENTRAP DISABLE MAG LOCK Tamper NO Tamper IN EDGE EDGE ID PLUG ERROR ALARM V ALARM RET 4V IN USE 0. MAGLOCK. TAMPER.. EDGE 4. EDGE 5. ID PLUG ERROR 6. ENTRAPMENT 7. REVERSE SENSITIVITY 8. OVERLOAD 9. NO 0. IN USE.. DISABLE 6. SECDARY LINE 7. LINE 8. SECDARY LINE 9. LINE Matrix LED Problem Condition LED is LED is FLASHING OVERLOAD LED is NO SW / LED is LOOP LED is FLASHING or contstantly LOOP LED is FLASHING or contstantly DISABLE LED is MAG LOCK LED is FLASHING TAMPER LED is FLASHING VDC LED is. 4VDC LED is Normal LED or 5 Solution(s) for Problem Condition Jumper between and is missing or broken (jumper is required if a sensor is not present). Sensor on input (photocell or edge) may have detected an obstruction while opening or closing gate. cell on input is misaligned with reflector. Sensor on input (photocell or edge) may not be wired properly, (see 7 ). Sensor is NOT a N.C. monitored sensor that is 5 06 compliant. Sensor on is damaged or malfunctioning. Sensor might need to be relearned. Check if gate is binding against catch post or bracket in opened or closed position. Check if gate moves manually with low resistance throughout its full range of motion. Check if chain is installed inline with idle wheels in both and D positions. Gate may be too heavy for operator (check manual for maximum gate capacity). Check if and magnets are still connected on chain. Loop fault condition: Check if loop wires are connected into to loop input connector properly. Check if loop detector is inserted properly in Matrix slot. Set unique loop detector frequency for each loop detector used. Loop Detector might be defective. Replace defective loop detector. NOTE: RENO loop detector LED s flash as default, but function normally (ignore the flashing). Loop fault condition: check if loop wires are connected into to loop input connector properly. Check if loops are wired in series. Check if loop detector is inserted properly in Matrix slot. Set unique loop detector frequency for each loop detector used. Loop Detector might be defective. Replace defective loop detector. NOTE: RENO loop detector LED s flash as default, but function normally (ignore the flashing). Check if Gate Shutoff switch is, Turn it. If it is, cycle the switch ( then ). Check if the chain is dropped. If so, gate is disabled for safety. Reinstall chain and cycle the "Gate Shutoff" switch ( then ) to enable operator. Check if an external device is triggering DISABLE input on Matrix. Disconnect devices individually to determine possible false triggering of DISABLE. Maglock power is lost. Check if maglock power transformer is wired properly to Matrix or needs to be replaced. Switch is set to delay but no maglock is connected. Set switch to Gate was manually moved off of its D position causing Tamper Relay to trigger for few seconds. Check for a short in wiring to connected device. DO NOT power external keypads or telephone entry to this port (only use for radio receiver / photocell) Standard Quick Install Rev 8

21 mc00 led troubleshooting Jumper UNUSED Entrapment Inputs to or a fault will occur. 0. EDGE 9. EDGE ENTRAPMENT Example: Inputs & are NOT used and MUST be jumpered to. 5. LINE 4. MATRIX LINE : LEARNED MITORED / : LEARNED MITORED / EDGE : MITORED LY Sensor Wire. LED.. OVERLOAD 6. Limit SW Entrap MC00 MATRIX JOG JOG LINE ENTRAPMENT INPUTS LED Motor OverLoad MC00 LED Problem Condition LED is MATRIX LINE LED is Limit SW LINE LED is OVERLOAD LED is Entrap LED is LED is EDGE LED is EDGE LED is flashing EDGE LED is EDGE LED is FLASHING LED is LED is FLASHING LED is Normal LED Solution(s) for Problem Condition Check if AC / (on toroid box) is. Check if power cable is plugged into back of MC00 Power In input. Check wiring between Matrix RS485 (+,, gnd) and MC00 RS485 (+,, gnd) terminals. Connect [ to ], [() to ()] and [ to ]. Check if limit switches are plugged into MC00 input on back. Check if gate is binding against catch post or bracket in opened or closed position. Check if gate moves manually with low resistance throughout its full range of motion. Check if chain is installed inline with idle wheels in both and D positions. Gate may be too heavy for operator (check manual for maximum gate weight for your model operator). An entrapment event has occurred, check an entrapment sensor was triggered (see if, EDGE, EDGE, or LED is on). An event may have occurred. Check for gate obstruction. sensitivity is too high for application. Readjust setting on MC00, (see 0 ). Sensor on EDGE input (photocell or edge) may have detected an obstruction while closing the gate. cell on EDGE input is misaligned with reflector. Sensor on EDGE input (photocell or edge) may not be wired properly, (see 7 ). Sensor is NOT a N.C. monitored sensor that is 5 06 compliant. Sensor is damaged or malfunctioning. Sensor might need to be relearned. Jumper between EDGE and is missing or broken (jumper is required if a sensor is not present). Sensor on EDGE input (photocell or edge) may have detected an obstruction while opening or closing the gate. cell on EDGE input is misaligned with reflector. Sensor on EDGE input (photocell or edge) may not be wired properly, (see 7 ). Sensor is NOT a N.C. monitored sensor that is 5 06 compliant. Sensor on EDGE is damaged or malfunctioning. Sensor might need to be relearned. Jumper between and is missing or broken (jumper is required if a sensor is not present). Sensor on input (photocell or edge) may have detected an obstruction while opening or closing gate. cell on input is misaligned with reflector. Sensor on input (photocell or edge) may not be wired properly, (see 7 ). Sensor is NOT a N.C. monitored sensor that is 5 06 compliant. Sensor on is damaged or malfunctioning. Sensor might need to be relearned. MOST sensitive setting for entrapment detection. Select a less sensitive setting (recommended level thru 6) Standard Quick Install Rev 8

22 BC7 module LED troubleshooting. REPLACE. IN ERROR Battery Voltage E / F BC7 Battery Module. VOLTAGE / Battery / Battery Replace Battery TEST Battery Battery IN Error To Turn ALL : Turn AC switch on Toroid. Battery power remains. Press and HOLD / button on BC7 until 4 LEDs turn, release button. WAIT for ALL LEDs to turn. Up to 0 sec. SHUT / BC7 LED Problem Condition VOLTAGE (E / F) LEDs, only E is. IN ERROR LED is. REPLACE LED is. Normal LED Solution(s) for Problem Condition Battery is very LOW. Check if AC power / switch is. If so, check AC power. Plug not plugged in to IN port on battery module (see below). Battery needs to be replaced if TEST fails and REPLACE LED is. /SOLAR IN Port: Megatron Toroid box connection. IN / Battery Pack Ports: Back of MC00 motor controller connections. connect to IN IMPORTANT /SOLAR IN before use Plug: MUST be plugged into IN port Before use. /SOLAR IN IN IN IN TO CTROLLER Battery Voltage E / F / Battery Battery Pack Battery Voltage E / F / Replace TEST Battery Battery Battery / Battery BC7 Battery Module Battery IN Error Replace TEST Battery Battery BC7 Battery Module Battery IN Error To Turn ALL : Turn AC switch on Toroid. Battery power remains. Press and HOLD / button on BC7 until 4 LEDs turn, release button. WAIT for ALL LEDs to turn. Up to 0 sec. Battery IN Error LED: Lights when there is a battery connection problem. Make sure battery plug # is plugged into IN port or there is no damaged or loose wires. TEST Battery Button: Press to show amount of battery power available when using battery power LY (Battery voltage LEDs will light respectively). Replace Battery LED: Replace battery when lit. / Battery Button: IMPORTANT: Battery power automatically turns when Megatron Toroid Box AC Switch is turned. To turn ALL to operator:. Turn AC Switch on Megatron Toroid Box. Battery power remains.. WAIT for 5 seconds.. Press and HOLD (approx. 5 seconds) the RED / button until BC7 LEDs turn, then release button. LEDs will turn. (Up to 0 sec.) 5 06 Standard Quick Install Rev 8 0

23 4 5 Commonly used Safety Sensor Wiring Min Max SENSITIVITY C NO Com NO C Set switch to LIGHT LIGHT DARK Adjustment: If the photocell does not respond to an obstruction, lower the sensitivity by turning adjustment counterclockwise. EDGE to NO DO NOT connect to #. N0 NOTE: DO NOT use 0K Resisitor included with photocell. Power 4 to 40 VAC 4 to 40 VDC OK to use VDC PWR V Polarity does NOT matter INPUTS MC00 Use motor controller when dual operators are used. Installation Steps:. Set switch to LIGHT. Wire V power to photocell. Wire motor controller EDGE to photocell NO Wire motor controller to photocell C 4. Align photocell to reflector 5. Adjust sensitivity PACK Power In ALARM Inputs & MUST be LEARNED to MITOR sensors. To LEARN inputs & :. MITORED Sensors MUST be wired to inputs BEFORE they can be learned. Any unused inputs MUST be jumpered.. Reversing and/or can be wired to either input or.. Press and HOLD the & buttons at the same time on Matrix until beep is heard, learn mode begins. MOTI PWR V LY power entrapment protection sensors with MC00 PWR V Jumper UNUSED Entrapment Protection Inputs or a fault will occur. MC00 Limit SW Entrap PWR 4V RS485 () RS485 MC00 PWR V MUST be used Learn mode lasts for 5 min. indicated by beeping. 4. LEDs WILL be for each detected sensor on MC00. LEDs WILL be for BOTH MC00s when dual operators are used. 5. Press button again within 5 min. to learn sensors and end learn mode, beeping stops. Inputs are now MITORED. Reversing LY OR unused inputs Inputs: MUST jumper MATRIX Sensor Guidelines A sensor MUST be wired to EDGE or operator WILL NOT function. Wire NORMALLY D (N.C.) MATRIX JOG JOG LINE MITORED sensors LY, to each operator s MC00 when dual operators are used. Reversing and/or can EDGE be wired to ANY of the Inputs. MC00 PWR V MUST be used to power MITORED sensors. UNUSED inputs MUST remain (Com) JUMPERED or fault will occur. LED Sensor Wire CAUTI: See installation instructions. ATTENTI: Voir la notice d installation. MC00 Slide Motor OverLoad omron EKR0K4 cell (Reflector) CLOSING Direction IMPORTANT: cell MUST be in alignment with reflector or fault will occur. 4 DIPSwitches O 4 N NOTE: Power must be cycled when switches are changed. emx irbret cell (Reflector) CLOSING Direction JP5 JP6 NOTE: To meet the 5 06 standard, Type B NonContact sensor entrapment protection device MUST be MITORED by the gate operator. SENSITIVITY Adjustment: If the photocell does not respond to an obstruction, lower the sensitivity by turning adjustment counterclockwise. O N 4 IMPORTANT: cell MUST be powered by or it will NOT be MITORED. NOTE: To meet the 5 06 standard, Type B NonContact sensor entrapment protection device MUST be MITORED by the gate operator. Installation Steps:. Set DIPswitches. Remove jumpers JP5 and JP6. Wire V power to photocell (VRX) 4. Wire motor controller EDGE to photocell (Energized) Wire motor controller to photocell (Energized) 5. Align photocell to reflector 6. Adjust sensitivity Jumper UNUSED Entrapment Protection Inputs or a fault will occur. Sensor Wire MC00 Inputs: MUST jumper Entrap Learn mode lasts for 5 min. indicated by beeping. 4. LEDs WILL be for each detected sensor on MC00. LEDs WILL be for BOTH MC00s when dual operators are used. 5. Press button again within 5 min. to learn sensors and end learn mode, beeping stops. Inputs are now MITORED. unused inputs Limit SW MATRIX JOG JOG LINE Jumper EDGE (Com) Remove BOTH Jumpers Inputs & MUST be LEARNED to MITOR sensors. To LEARN inputs & :. MITORED Sensors MUST be wired to inputs BEFORE they can be learned. Any unused inputs MUST be jumpered.. Reversing and/or can be wired to either input or.. Press and HOLD the & buttons at the same time on Matrix until beep is heard, learn mode begins. LY MOTI LED Motor OverLoad Jumper Power In ALARM Reversing OR CAUTI: See installation instructions. ATTENTI: Voir la notice d installation. INPUTS 0K 4W W PACK LY power entrapment protection sensors with MC00 PWR V MC00 PWR V MUST be used Sensor Guidelines A sensor MUST be wired to EDGE or operator WILL NOT function. Wire NORMALLY D (N.C.) MITORED sensors LY, to each operator s MC00 when dual operators are used. Reversing and/or can be wired to ANY of the Inputs. MC00 PWR V MUST be used to power MITORED sensors. UNUSED inputs MUST remain JUMPERED or fault will occur. MC00 Slide PWR V MATRIX RS485 RS485 () PWR 4V Polarity does NOT matter PWR V MC00 Use motor controller when dual operators are used. 0K 4W W VRX ENERGIZED PSE OUT NO E C VRX VTX N.C. Com Power NOTE: If photocell does NOT function using VRX power input, connect power to VTX input instead Standard Quick Install Rev 8

24 emx irbmon Transmitter (TX) CLOSING direction ThruBeam Receiver (RX) cell (ThruBeam) CLOSING Direction Single Gate Operator To EDGE and PWR V Input To PWR V Input Transmitter (TX) TX INPUT TRANSMITTER BOARD (TX) Green LED Gate Closed Single Operator Installation Steps:. Set DIPswitches on receiver.. Install jumper on receiver.. Wire V motor controller power to receiver. 4. Wire motor controller EDGE to receiver photocell. Wire motor controller to receiver photocell. 5. Wire V motor controller power to transmitter. 6. Align photocells. 7. Adjust sensitivity on receiver. TX RX Adjustment: If the photocell does not respond to an obstruction, lower the sensitivity by turning adjustment counterclockwise. DIPswitches:,, are. Switch 4 is If trouble occurs, try turning switch 4. NOTE: Power must be cycled when switches are changed. Jumper MUST be on Com. NO Com NO JUMPER IMPORTANT: cells MUST be in alignment or fault will occur. Green LED will remain receiver when in proper alignment. Receiver (RX) RX NO 4 DIP INPUT RECEIVER BOARD (RX) SENSITIVITY EARTH Green LED Jumper Common PWR V Polarity does NOT matter Normally Closed IMPORTANT: cells MUST be powered by or they will NOT be MITORED. NOTE: To meet the 5 06 standard, Type B NonContact sensor entrapment protection device MUST be MITORED by the gate operator. Power In Inputs & MUST be LEARNED to MITOR sensors. To LEARN inputs & :. MITORED Sensors MUST be wired to inputs BEFORE they can be learned. Any unused inputs MUST be jumpered.. Reversing and/or can be wired to either input or.. Press and HOLD the & buttons at the same time on Matrix until beep is heard, learn mode begins. MOTI Learn mode lasts for 5 min. indicated by beeping. 4. LEDs WILL be for each detected sensor on MC00. LEDs WILL be for BOTH MC00s when dual operators are used. 5. Press button again within 5 min. to learn sensors and end learn mode, beeping stops. Inputs are now MITORED. INPUTS Inputs: MUST jumper unused inputs PACK LY ALARM LY power entrapment protection sensors with MC00 PWR V PWR V RS485 RS485 () MATRIX MC00 PWR V MUST be used Sensor Guidelines A sensor MUST be wired to EDGE or operator WILL NOT function. Reversing Wire NORMALLY D (N.C.) MITORED sensors LY, to each operator s MC00 when dual operators OR are used. Reversing and/or can be wired to ANY of the Inputs. MC00 PWR V MUST be used to power MITORED sensors. UNUSED inputs MUST remain JUMPERED or fault will occur. CAUTI: See installation instructions. ATTENTI: Voir la notice d installation. PWR 4V MC00 Slide Jumper UNUSED Entrapment Protection Inputs to or a fault will occur Standard Quick Install Rev 8