WIRELESS NETWORK USER MANUAL MHz RFT-868-PIR Wireless Passive Infrared Sensor
|
|
- Pierce Palmer
- 6 years ago
- Views:
Transcription
1 WIRELESS NETWORK USER MANUAL MHz RFT-868-PIR Wireless Passive Infrared Sensor
2 Device Specifications Power Supply: 3V (2xAAA battery) Current Draw in standby mode: 12µA Temperature Working Range: C Volumetric Coverage: 8 20 m Dimensions ( L x W x H ): 60 x 42 x 120 mm Radio Module TRX Features 1 Low Rx power consumption: 10mA. Low Tx power consumption: Radio Operative Frequency: MHz FSK Modulation. Good reception sensitivity: down to -100 dbm at 25 kb/s in FSK. Transmit power: 7 dbm Packet handling feature with data whitening and automatic CRC generation. Incoming sync word recognition. Distance coverage: up to 20 m indoors (depending on building materials). Effective Radiated Power (ERP): 5mW. RFTide Network Features Wireless mesh network topology. Proprietary routing protocol and software application. Centrally managed network from a Control Unit. Advanced Encryption Standard (AES) of the data. Typical Applications Wireless alarm and security systems. Wireless sensor networks. Automated Meter reading. Home and building automation. Industrial monitoring and control. Remote wireless control. Revision History Date Version Revision 15/09/ Initial Release 1 Refer to RFTide Transceiver for mesh network datasheet
3 CAUTION Read this manual before attempting to install the device! Failure to observe recommendations included in this manual may be dangerous or cause a violation of the law. The manufacturer Udoit Srl will not be held responsible for any loss or damage resulting from not following the instruction of operating manual. When handled carelessly or used in non-specified environment conditions, the device may not function properly. It s highly recommended to ensure safety and property protection. The RFT-868-PIR is a battery-powered device. Using batteries other than specified may result in explosion. Dispose of properly, observing environmental protection rules.
4 DESCRIPTION...5 FIRST CONFIGURATION...6 WALL MOUNTING...7 DEVICE SETTINGS...8 MAINTENANCE...10 LENS COVERAGE DIAGRAMS...11
5 DESCRIPTION The RFT-868-PIR is the RFTide device suitable for volumetric detection purposes. It is composed by a passive infrared sensor and a radio module working at the frequency of 868.3Mhz. The alarm is activated by the dual element pyro-electric sensor which reveals the body heat and through the radio module it will send the information to the control unit. That kind of device fits the room and offices requirements and due to its sensitivity regulation it s useful also for smaller environment. The use of the microcontroller digital technology combined with Fresnel optics allows a huge resolution in the alarm detection (37 ray bundle on 3 horizontal plane), false alarm immunity and high reliability with no sensitivity reduction; in particular a digital implemented impulse counter is used for false alarm avoidance. The device is protected against tampering with a notification signal to the control unit. It has an adjustable volumetric detection coverage from 8 meters to 20 meters and 100 wide range. During the inhibit time of 4 minutes, after a stabilization of 40 seconds of the sensor, the device stores every event (alarm and tamper) and send it after the inhibition. Low consumption in standby mode allows to obtain a long lifetime of the batteries. The mounting support helps to obtain the right angulation of the device. Figure 1 : PIR sensor external view and mounting support items
6 Figure 2 : PIR sensor internal view with description FIRST CONFIGURATION Referring to Figure 2, these first steps must be followed: a. Remove the screw from the bottom and then open the case of the device. b. As per first configuration, set the dipswitch as follow: 1. OFF 2. OFF 3. ON 4. OFF c. Insert the 2 triple-a batteries. d. Follow the Learning Procedure part explained in the chapter DEVICE SETTINGS at page 8. e. For advanced setup refer to Table 1 Dip-switch configuration at page 9.
7 WALL MOUNTING I. Mounting without brackets Figure 3 : Backplate of the case 1. Remove the front panel and then the printed circuit board using the plastic clip on position M of Figure Make holes in positions P if the device will be placed on a flat wall or positions A if it will be placed in a corner. Holes must be 6 mm maximum of diameter, consider that the bottom of the device will be the round shaped one. It s suggested to be placed at 2.10 m height. 3. Place the printed circuit board, the batteries and close the front panel. II. Mounting with brackets 1. Fix the bracket in the bottom of the case with the screws. 2. Place the bracket in the wall, about at 2.10 m height, then direct the device to the desired area, consider an angle of about 6 to the wall. 3. Mount the batteries and close the front panel. Figure 4 Typical mounting cases
8 III. Mounting recommendations: In order to have a correct installation and to avoid false alarms some basic rules must be followed: Place the device on stable surfaces and not subject to vibrations. Do not install the device exposed to sun light or source light(e.g. lamps). Do not install the device near air flows (e.g. air conditioner). Do not install the device pointing any source of heat (e.g. radiators, fireplaces, cookers). Do not point the sensor direct to glass surfaces. I. Learning procedure DEVICE SETTINGS In order to let the device communicate with the Control Unit of the existing RFTide network the following steps must be done: 1. Keep pushing the Learn button (Figure 2) for about 3 seconds, till a red led turns on. 2. Till 15 seconds, the Control Unit has to send a PROGR_MESSAGE signal to the device. That message must contain the node address which the sensor will be assigned and the Network ID. 3. If the message is received, the red led must be blinking for a while, then it turns off. II. Keep Alive Referring to Figure 2, the Keep Alive button permit the device to send instantly a message as follow: Command: SEND_PACKET 0x00 0x00 Destination: Control Unit address 0x[Control Unit ID] Payload Byte 0: PIR Device 0x01 Payload Byte 1: Keep Alive message 0x01 Payload Byte 2 7. Not used 0x00..0x00 III. Alarm Status In case of alarm, the device send message as follow: Command: SEND_PACKET 0x00 0x00 Destination: Control Unit address 0x[Control Unit ID] Payload Byte 0: PIR Device 0x01 Payload Byte 1: Alarm message 0x03 Payload Byte 2. Alarm Code 0x[see Table 2] Payload Byte 3: Battery Status 0x[see Table 3] Payload Byte 4-5: Not used 0x00 0x00 Payload Byte 6-7: Alarm Number 0x[Incremental value]
9 As for every SEND_PACKET message, the RFTide module re-send the message in case that the ANSWER_MESSAGE from the Control Unit is not received. The sensor will make 2 retry and then goes off after 1 second. IV. Configuration Tables Dip-switch Configuration ON OFF Dip1 Radio Mode Continuous radio Normal Status TX for 1 minute Dip2 Supervision Active Not Active Dip3 Pulse Counter Active Not Active Dip4 Inhibition 4 minutes of inhibition 4 seconds of inhibition Table 1 Dip-switch configuration If there re some doubts about the radio coverage of the module, it is possible to put the device in continuous transmission mode for 1 minute with the dip-switch 1 (Radio Mode), after that it will turn back to normal status. To put back in continuous transmission mode it s necessary to turn off and then on again. See Table 2 for the radio mode bit status. To set the supervision of the device it s necessary to turn on the dip-switch 2 (Supervision), in this way the radio module will transmit a supervision message every 60 minutes (see Table 2 for the supervision bit status). In order to avoid false alarms it is possible to set the number of ray bundles that has to be crossed for trigger the device with the dip-switch 3 (Pulse Counter), active means 2 rays in 20 seconds, not active means it starts immediately. During the setup of the device it s important to understand the quality of the communication, to do so it s necessary that the device transmit data as much as possible. For that the inhibition time could be changed with the dip-switch 4 (Inhibition Time): every alarm that the device detects is stored and then sent at the end of the inhibition time. It s suggested to use 4 seconds for setup time and 4 minutes for normal operations. PIR Alarm Code (Byte 2) [1=Active; 0=Not Active] Bit 0 PIR Bit 1 Tamper Bit 2 Not used Bit 3 Not used Bit 4 Not used Bit 5 Not used Bit 6 Supervision Bit 7 Radio Mode Table 2 PIR Alarm Code
10 Battery Status (Byte 3) Low Level Batteries (< 2.15V) Normal Level Batteries (> 2.15V) Table 3 Battery Status,Low level is about 2.15 V MAINTENANCE In order to replace the batteries, remove the front plate and place the triple-a batteries as per Figure 2. We suggest to use alkaline batteries. The accidental reversal of the polarity won t cause any electrical damage to the device or batteries drain. In case of loosing of acid from batteries, remove them and clean the contacts. If the sensor lens is dirty clean it with a dry soft cloth. Here follows some cases which could be resolved easily. Buzzer goes on when the batteries are inserted in the holder: That s the indicator of the low voltage alarm. The batteries need to be replaced and if the radio module is already configured in the RFTide network, the Control Unit will receive a low battery message. The Control Unit doesn t receive any message from the PIR: There could be a dual problem, to avoid radio issues it s necessary to repeat the learning procedure as described in the chapter DEVICE SETTINGS at page 8 or the configuration of the dip-switch is wrong, see point b of the chapter FIRST CONFIGURATION at page 6. The device can t detect far/close distances: Be sure to have mounted the device properly as per Figure 4 and check the sensitivity regulation trimmer show in Figure 1.
11 LENS COVERAGE DIAGRAMS Figure 5 Lens Coverage
WIRELESS OUTDOOR DUAL TECHNOLOGY MOTION DETECTOR AOD-200
aod-200_en 05/16 WIRELESS OUTDOOR DUAL TECHNOLOGY MOTION DETECTOR AOD-200 SATEL sp. z o.o. ul. Budowlanych 66 80-298 Gdańsk POLAND tel. +48 58 320 94 00 www.satel.eu Firmware version 1.0 WARNING The device
More information1126 Series Ceiling Mount PIR Motion Detector
Installation Sheet 1126 Series Ceiling Mount PIR Motion Detector Description The 1126 Series PIR (Passive Infrared) Motion Detectors are a compact wireless PIR. The 1126 Series offer 360, Wide Angle, or
More information>WIRELESS> ALARM SYSTEM CR200
intrusion >WIRELESS> ALARM SYSTEM CR200 INTRUSION HOME SECURITY CR200 is a Modern, Effective and Versatile 20-zone Household Security System. It is packed with simple Plug & Play functionality, designed
More information1125 PIR Motion Detector
Tamper Survey LED INSTALLATION SHEET 1125 PIR Motion Detector Description The 1125 PIR (Passive Infrared) Motion Detector is a wireless, low current sensor for use with the 1100D Wireless Receiver. Using
More informationEnglish. Italiano. Português. Françias. Español
DT AM Grade 3 Español Françias Português Italiano English High Ceiling Mount Detector Installation Guide English DT AM Grade 3 High Ceiling Mount Detector Installation Guide General Description The Industrial
More informationAdvanced DIGITAL Wired PIR Motion Detector
PRELIMINARY Advanced DIGITAL Wired PIR Motion Detector The PIRfect PYR-2021 provides DIGITAL Passive Infra Red (PIR) motion detection across a volumetric area, with versatile advanced SPHERICAL SEALED
More informationPIR-100B User Manual
Wireless Passive Infrared Motion Detector PIR-100B User Manual Ver 1.00 Date Issued: 2010-06-08 All rights reserved by King Pigeon Hi-Tech. Co., Ltd. Website: Http://www.GSMalarmsystem.com Table of Contents
More informationINTERNAL DETECTORS. Wired and two-way wireless grade 2 and 3 internal detectors
INTERNAL DETECTORS Wired and two-way wireless grade 2 and 3 internal detectors An extensive range of internal detectors utilising the latest Pyronix patented technologies for residential, commercial and
More informationUNICA - ALARM SYSTEM WITH VISUAL VERIFICATION. All in One - All in Touch Video - Alarm System
UNICA - ALARM SYSTEM WITH VISUAL VERIFICATION All in One - All in Touch Video - Alarm System UNICA is a revolutionary alarm system based on architecture all-in-one composed by a burglar alarm (wired and
More informationpowered by Note: This manual applies to several packages. As such, some parts and some steps may not pertain to the package that you purchased.
MivaLife powered by Note: This manual applies to several packages. As such, some parts and some steps may not pertain to the package that you purchased. 1 Contents TripleShield At A Glance...3 Assemble
More informationGJD OPAL RFX WIRELESS 35 METRE EXTERNAL PIR INSTALLATION MANUAL
GJD OPAL RFX WIRELESS 35 METRE EXTERNAL PIR INSTALLATION MANUAL A WIRELESS PASSIVE INFRARED DETECTOR AND THREE CHANNEL RECEIVER THAT SIMULTANEOUSLY OR INDIVIDUALLY CONTROLS CCTV SWITCHERS, VIDEO RECORDERS
More information2 x CR123A Lithium batteries. White night-light LED. Blue alarm LED - also glows behind the lens. Ambient light sensor behind lens.
15m x 15m wide angle coverage Look down Creep Zone White LED motion activated night-light Adjustable Pulse Count Adjustable Range High R.F. and E.S.D. immunity High white light immunity SAWR stabilised
More informationWireless Internal Siren System Installation Guide
Wireless Internal Siren System Installation Guide FW-VESTA -8/9F FW-SIREN2CP -8/9F P/N 7101958 July 2010 Copyright Crow Engineering Ltd. 2008 The copyright of this document is owned by Crow Engineering
More informationDescription. Optex Incorporated
Optex Incorporated Description 1845 W. 205 th St. Torrance, CA 90501-1510 USA TEL (310) 533-1500 and (800) 966-7839 FAX (310) 533-5910 Doc: Model: Desc: Architect/ Engineer Specifications CX-502 PIR Intrusion
More informationSHEPHERD. Smart solutions to protect and manage what matters the most to you
SHEPHERD Smart solutions to protect and manage what matters the most to you Security Shepherd Gateway & Keypad, Repeater, PIR Detectors, PIR Camera, Magnet, Glass Break, Siren 1-10 Safety & Air Quality
More informationIN A BOX. User Manual YOUR HOME SECURITY SYSTEM. curv360.co.uk. Support APP remote arm/disarm, parameter settings and accessories management
YOUR HOME SECURITY SYSTEM IN A BOX 2.4-inch TFT colour display screen Support multi-language GSM network time automatically GPRS real-time networking online WIFI / GSM / 3G / GPRS networking alarm Support
More informationJUNE 2014 SECURITY SYSTEMS
JUNE 2014 SECURITY SYSTEMS LINCE ITALIA S.p.A. Being professionals and a recognized leader in security from 1975, as well as being inspired, commits us offering to our customers the technologically most
More informationWIRELESS ALARM SYSTEM CR200 >SMART GPRS INTRUSION DETECTION PLUG & PLAY FUNCTIONS SELF-LEARNING, SMART FEATURES TEXT ZONE NAMING
>SMART GPRS WIRELESS ALARM SYSTEM CR200 INTRUSION PLUG & PLAY FUNCTIONS SELF-LEARNING, SMART FEATURES TEXT ZONE NAMING INTRUSION HOME SECURITY CR200 is a smart GPRS modern, effective and versatile 30-zone
More informationWM3000 WIRELESS MODULES
WM3000 WIRELESS MODULES $$:05 $$:07 INSTALLATION INSTRUCTIONS Table of Contents Installation... 3 Mounting Instructions & Connections... 3 Setting the Dip Switches... 4 Setting the Recognition Time...
More informationHSD-200Z Z-Wave Motion Sensor
HSD-200Z Z-Wave Motion Sensor The HSD-200Z is a Z-Wave TM enabled device and is fully compatible with any Z-Wave TM enabled network. Z-Wave TM enabled devices displaying the Z-Wave TM logo can also be
More informationSEPTEMBER SECURITY SYSTEMS REV.00
2017 SEPTEMBER SECURITY SYSTEMS F E E L S E C U R E REV.00 LINCE ITALIA S.p.A. Since 1975 LINCE ITALIA is recognized as a leader in the Security Industry. This success comes from a longstanding experience
More informationFW-SIREN2EXT -8/9F FW-SIREN2CP -8/9F
Wireless Siren System Installation Guide FW-SIREN2EXT -8/9F FW-SIREN2CP -8/9F P/N 7101866 Rev. 04 Jan 2010 Copyright Crow Engineering Ltd. 2008 The copyright of this document is owned by Crow Engineering
More informationMotion Detector User Guide
Care@Home Motion Detector User Guide ESUGSC008 Version 2.0 September 2017 Table of Contents Table of Contents 1. Overview... 3 2. Installing the PIR... 4 2.1. Determining the Best Location... 4 2.1.1 Basic
More informationEWP2WIRELESS MOTION DETECTOR
EN EWP2WIRELESS MOTION DETECTOR User manual v1.2 Compatible with: ESIM364 v02.08.00 and up. EPIR3 v1.2.0 and up EPIR2 v01.03.02 and up Main features: Built-in dual element passive infrared (PIR) sensor.
More informationExternal Wireless Sounder
External Wireless Sounder Model: WL RWS401 Installation and Programming Instructions Table of Contents Introduction... 3 Operational Functions... 3 Alarm / Tamper Indication... 3 Low Battery Indication...
More informationPRODUCT CATALOGUE. Cape Town 18 Darter Road Blue Water Estate Kommetjie. Gauteng 245 Louis Botha Avenue Orchards Johannesburg
PRODUCT CATALOGUE Cape Town 18 Darter Road Blue Water Estate Kommetjie Luke Fowles - 076 161 8124 luke@providenttech.co.za Frank Fowles - 082 445 1541 frank@providenttech.co.za www.providenttech.co.za
More informationIX30 - Z-Wave PIR Detector User Guide
IX30 - Z-Wave PIR Detector User Guide Ⅰ. Introduction IX30-Z-Wave is a digital micro-control intrusion detector adopting Energy Accumulation Logical Processing & Random Dynamic Time Segmentation Technology.
More informationThe Genesis. Wireless PIR System. Se t t i n g n e w s t a n d a r d s f o r P I R d e t e c t i o n. BS8418 Compliant
Se t t i n g n e w s t a n d a r d s f o r P I R d e t e c t i o n The Genesis Wireless PIR System BS8418 Compliant S e t t i n g n e w s t a n The Genesis Wireless PIR System BS8418 compliant The GENESIS
More informationPERMACONN PM1030 Includes DI300. Installation Manual
PERMACONN PM1030 Includes DI300 Installation Manual Radio Data Comms Unit 5/20-30 Stubbs Street Silverwater NSW 2128 Telephone: 02 9352 1777 Facsimile: 02 9352 1700 Introduction The PERMACONN system provides
More informationDUAL TECHNOLOGY SENSOR (PIR + Microwave) Outdoor use INSTALLATION MANUAL
DUAL TECHNOLOGY SENSOR (PIR + Microwave) Outdoor use INSTALLATION MANUAL 1. DESCRIPTION Dual Technology Sensor (PIR + Microwave). AND operation in the prevention of "false alarms". IP65 (indoor and outdoor).
More informationPremium 8 Zone Wireless Alarm Kit
Premium 8 Zone Wireless Alarm Kit INTRODUCTION The wireless alarm system is designed to protect your home. It is a simple to use, easy to install unit. No special tools or training are required, all fixings
More informationA1UL PERS. Personal Emergency Response System. For Technical Support Please Contact Your Service Provider Or Distributor
A1UL PERS Personal Emergency Response System TABLE OF CONTENTS 1. READ THIS FIRST... 1 2. SYSTEM OVERVIEW.. 1 3. COMPONENTS 2 4. UNIT OPERATION! Standby Mode.. 3! Emergency Activation. 3! Answering Incoming
More informationXHS1-TY / MP-841 ZigBee Home Automation 1.2 Wireless Digital Pet Immune PIR Detector
XHS1-TY / MP-841 ZigBee Home Automation 1.2 Wireless Digital Pet Immune PIR Detector Installation Instructions 1. INTRODUCTION The XHS1-TY or MP-841 (pet immune) is a microprocessor-controlled wireless
More informationX64 Wireless Training
X64 Wireless Training IDS Contents 1 Contents Features 3 Wireless Hardware 4 IDS & Duevi integration PCB 5 LED operation 5 Wireless Device Hardware setup 6 Location 260 7 LED Keypad Instructions 7 Adding
More informationEnglish. Series. Installation and Use Manual
English Series FOSTER Installation and Use Manual FOSTER Rev.13 03/2015 MITECH srl reserves the right to change the information in this document without warning. Index Anti-intrusion barrier 3 Main components
More information5800-OD Wireless Outdoor Motion Sensor Installation Instructions
GENERAL INFORMATION The Honeywell 5800-OD Wireless Outdoor Motion Sensor (referred to as the 5800-OD) combines the convenience of wireless technology with a full featured outdoor PIR motion sensor. The
More informationWireless Occupancy Sensor, Ceiling Mount (WOS2-CM)
21233 Wireless Occupancy Sensor, Ceiling Mount Installation Instructions The Daintree Networks ceiling mounted Wireless Occupancy Sensor operates seamlessly within the ControlScope Manager (CSM), the Daintree
More informationdesign line performance line Guardall DesignLine & PerformanceLine detector series 2015 Peace of mind
design line performance line Guardall DesignLine & PerformanceLine detector series 2015 Peace of mind Peace of mind The Guardall sensor range comprises two series of motion sensors intended for use in
More informationPOP_ Smoke Detector
POP_004308 Smoke Detector Firmware Version : 1.0 Quick Start S This device is a wireless Z-Wave sensor. Exclusion, Inclusion are confirmed by hitting the programm button for 1 sec when the sensor is removed
More informationInstruction Manual Water Sensor
Instruction Manual Water Sensor Thank you for your support Please read the instruction manual carefully before operating Please keep the instruction manual for future reference Shenzhen NEO Electronics
More informationExternal Wireless Sounder
External Wireless Sounder WL S50 Installation and Programming Instructions 2 Wireless Sounder Instructions Table of Contents Introduction... 4 Operational Functions... 4 Alarm / Tamper Indication...4 Low
More informationConstruction of Wireless Fire Alarm System Based on ZigBee Technology
Available online at www.sciencedirect.com Procedia Engineering 11 (2011) 308 313 The 5 th Conference on Performance-based Fire and Fire Protection Engineering Construction of Wireless Fire Alarm System
More informationWireless Occupancy Sensor, Wall Mount with Photosensor (WOS2-WM)
Installation Instructions The Daintree wall mounted Wireless Occupancy Sensor (WOS2-WM) operates seamlessly within the Daintree wireless lighting control platform. The WOS2-WM is a battery-powered occupancy
More informationPOP_ Smoke Detector
POP_004308 Smoke Detector Firmware Version : 1.0 Quick Start S This device is a wireless Z-Wave sensor. Exclusion, Inclusion are confirmed by hitting the programm button for 1 sec when the sensor is removed
More informationApplications: 27. NETIChome mobile ios 28. NETIChome mobile Android. NETIChome basic elements
INDEX 1 NETIC... 2 2 Door/Window detector MINI... 2 3 FOUR sensor... 3 4 Smoke detector... 3 5 Flood detector... 4 6 ILLumination sensor... 4 7 Lamp holder... 5 8 Siren... 5 9 Power meter & switch... 6
More informationMADE TO PROTECT OUTDOOR DUAL-TECH CURTAIN DETECTORS AGATE / AOCD-250
MADE TO PROTECT OUTDOOR DUAL-TECH CURTAIN DETECTORS / EASY INSTALLATION AND CONFIGURATION COMPACT ENCLOSURE FOR INDOOR AND OUTDOOR USE RELIABLE DETECTION Detector applications in residential, business
More informationADPRO PRO Passive Infrared Detector. Webinar November Ben Klösen, PLM
ADPRO PRO Passive Infrared Detector Webinar November 2015 Ben Klösen, PLM What is the principle of Infra-Red detection? Humans and most other live forms radiate infra-red waves in band lengths from 7 to
More informationFCD-wire Contents. List of Figures
FCD-wire Contents FCD-X21 Configuration 1 Introduction... 1 2 Opening the FCD Application... 1 3 FCD Window... 2 4 FCD LEDs... 3 5 Configuration Operations... 4 FCD Info...4 FCD System Info...5 FCD Interface
More informationDD205RF/TX Detector Installation Sheet
GE Security DD205RF/ Detector Installation Sheet EN DE EL ES FR IT NL PT RU TR 2009 GE Security, Inc. 1 of 28 P/N 1060783 REV 1.00 ISS 26FEB09 2 of 28 P/N 1060783 REV 1.00 ISS 26FEB09 EN: Installation
More informationV1.0. Smart Home Alarm System. User Manual. APP download via QR Code scanning. Please read the manual carefully before using.
V1.0 Smart Home Alarm System User Manual APP download via QR Code scanning Please read the manual carefully before using. Content FUNCTION PROFILE 2 THE SCHEMATIC GRAPH OF HOST 3 PROCESS OF BOOTING 6 OPERATION
More informationWireless Alarm system s manual
MOUNTVIEW TECH AUSTRALIA PTY LTD Wireless Alarm system s manual ADS ECO GSM320 Series ADS Security 1/11/2011 1. Before You Begin For your safety and the safety of others, and to ensure that you get the
More informationWHAT S IN THE BOX? The IQ Panel also includes a snap on table stand and power supply with cable.
WHAT S IN THE BOX? The IQ Panel 2 keeps you connected to an entire ecosystem of smart devices giving you control over your entire home. Exciting features like touchless disarming using Bluetooth and a
More informationHDCVI PIR Camera User s Manual
HDCVI PIR Camera User s Manual Version 1.0.1 Table of Contents 1 General Introduction... 1 1.1 Overview... 1 1.2 Features... 1 2 Device Framework... 2 3 Detection Range... 4 4 Device Installation... 5
More informationKwêBeams Effective wire free outdoor early warning system
1 KwêBeams Effective wire free outdoor early warning system Features: - Easy to install & use - Operates on 868Mhz frequency (less congested to avoid signal jamming) - All sensors with built in sirens,
More informationECO N DATE DESCRIPTION OF CHANGE CHG
Model Number: M21E-24-DIN Description: The product is a loop powered device which controls an unsupervised dual pole output channel suitable to manage 24VAC loads. The M21E-24-DIN is micro-controller operated,
More informationTotal Connect Box. User manual
Total Connect Box User manual 1 Congratulations on your purchase of the Honeywell Total Connect Box security system. To make the best out of your system we advise you to read this manual carefully. This
More informationWireless D.I.Y. Alarm Kit
Wireless D.I.Y. Alarm Kit User Manual December 2010 MAMI 21 Hubert Mathew Road Illiondale 1610 Tel: +27 11 452 4737 Email: sales@mami.co.za page 2/10 General The Wireless DIY kit, is a pre-programmed,
More informationRoboguard Technicians Manual Contents
Roboguard Technicians Manual Contents Roboguard 1 Page Roboguard Diagram of Roboguard 2 Installation 3 Walk Test 4 Configuration 5-6 Beam Range 6 Minimising False Alarms 7 Blocking off beams/maintenance
More informationACTIVE INFRARED BARRIER
Although PROTECH provides high security indoor intrusion sensors for the military and government markets, our specialty is outdoor protection. Since we first introduced our PIRAMID outdoor dual technology
More informationPRODUCT DIAGRAM PACKAGE CONTENTS
PRODUCT DIAGRAM PACKAGE CONTENTS After receiving the product, please inventory the contents to ensure you have all the proper parts, as listed below. If anything is missing or damaged, please contact Monoprice
More informationGeneral Description. Industrial LuNAR DT AM Grade 3 Features
DT AM Grade 3 High Ceiling Mount Detector Installation Guide General Description The Industrial LuNAR DT AM Grade 3 is a dual technology ceiling detector with a mounting height of up to 8.6m (28ft) that
More informationThe system is expanded via the RCC network with each RCC capable of passing information to and from up to 31 detection or output devices.
FireCell Radio Hub Fully addressable Wireless activation Third party approved (EN54) 2-way radio communication Loop powered Diagnostics port Range in excess of 150 metres Overview The model FCX-500-001
More informationWireless Driveway and Intruder Alert
Wireless Driveway and Intruder Alert USER MANUAL SFA600 PLEASE READ THIS USER MANUAL COMPLETELY BEFORE OPERATING THIS UNIT AND RETAIN THIS BOOKLET FOR FUTURE REFERENCE. COMPLIANCE WITH FCC REGULATIONS
More informationUSER GUIDE WIRE-FREE HOME PROTECTION SYSTEM AG100+ CONTENTS
CONTENTS USER GUIDE WIRE-FREE HOME PROTECTION SYSTEM AG00 Section Getting started. General system overview. Introduction to the system. Items included with the system. Introduction to the Smart Panel.5
More informationWireless Call Point ( )
Wireless Call Point (100-821) INSTALLATION MANUAL Wireless Call Point Installation Manual Rev2.1 TABLE OF CONTENTS 1. Introduction... 2 FEATURES:...2 2. Normal Operation... 3 3. LED Indicator...3 4. Physical
More informationSimple Instructions for the WisePIR
Simple Instructions for the WisePIR General Description of use. INSTALLATION 2 Channel movement detector for use with Wise Control Radio Receivers. Note: The WisePIR will send a programming signal for
More information80 CHANNELS WIRELESS RECEIVER WITH LCD DISPLAY M1.1.1-Hx.x-F1.1-ENG [AN] [SPV] MADE IN ITALY INSTALLATION AND USE MANUAL
RX808-LCD 80 CHANNELS WIRELESS RECEIVER WITH LCD DISPLAY 14.12-M1.1.1-Hx.x-F1.1-ENG [AN] [SPV] MADE IN ITALY INSTALLATION AND USE MANUAL WARNINGS Installation: This device must be installed only by qualified
More informationMKTCTBLEFURTINC R001. Catalogue nd Edition
MKTCTBLEFURTINC R001 Catalogue 2009 2 nd Edition control panels KYO32 Expandable hybrid panel for medium-size installations The KYO32 control panel has 8 zones, expandable to 32 zones on BPI bus. The system
More informationSF812 SMOKE DETECTOR. Include to or Exclude from a Z-Wave TM Network. Product Overview
SF812 SMOKE DETECTOR The photoelectric Smoke Detector is a Z-Wave TM enabled device which is fully compatible with any Z-Wave TM enabled network. Z-Wave TM enabled devices displaying the Z-Wave TM logo
More informationIntrunet Wireless Portfolio for Intrunet SPC Series Intrunet SI Series and IC60
Intrunet Wireless Portfolio for Intrunet SPC Series Intrunet SI Series and IC60 Comprehensive wireless portfolio for a wide range of residential and commercial applications Maximum device positioning flexibility
More informationINTRUDER ALARM SOLUTIONS PRODUCT LIST 2012
EN INTRUDER ALARM SOLUTIONS PRODUCT LIST 2012 Intruder and Fire Alarm Systems Teletek Electronics is the biggest Bulgarian manufacturer of whole range intruder and fire alarm systems. The Company was founded
More informationD-TECT Dual Tech. GJD360 Triple Technology External Detector
D-TECT Dual Tech GJD360 Triple Technology External Detector PACKAGE CONTENTS 1 x Dual Tech 1 x Drilling template for fixing holes 3 x 31.75mm wall plugs 3 x 31.75mm screws 2 x Spare Sliding Curtains 2
More informationTRUST WIRELESS ALARM SYSTEM 200S
UK TRUST WIRELESS ALARM SYSTEM 200S User s Manual Version 1.0 Thank you Thank you very much for purchasing this product from the Trust assortment. We wish you hours of fun with it. Please read this manual
More informationQuick Installation Manual LED Touch Keypad Autodial Wireless Alarm System
Quick Installation Manual LED Touch Keypad Autodial Wireless Alarm System By shield4u http:// (Version 20110816) A. Alarm Understanding Away Disarm Home Emergency Function Signal Interpretation Buzzer
More informationWireless Plug Load Control
General Specification Wireless Plug Load Control Model No.: PL20R & PLBPC Description:Enerlites Wireless Plug Load Controller is designed with simplicity, and helps to make plug load control requirements
More informationS3 Sim Secual Alarm system with GSM transmitter
S3 Sim Secual Alarm system with GSM transmitter www.etiger.com Features Control Panel Layout (Back) - ARM CPU + Auror CPU - GSM frequency: 850 / 900 / 1800 / 1900 MHz, suits all phones - Supports up to
More informationWireless Smart Metering LAN-WMBUS-M. Wireless MBUS, door and window sensor. With optional glass break accessory.
Wireless Smart Metering LAN-WMBUS-M Wireless MBUS, door and window sensor. With optional glass break accessory. The LAN-WMBUS-M (I/A) (G)/(E)- is a activity sensor for detecting for example openings/closing
More informationOpen Source Home Security System
Open Source Home Security System Final Report ECE 410: Senior Project By: Allen Chu March 28, 2012 Project Advisor: Dr. John Ventura, PE Table of Contents Title 1 Table of Contents 2 1. Abstract 3 2. Customer
More informationHome Doorway Alert Kit
READ ME FIRST DIY WIRELESS ALERT Home Doorway Alert Kit EN Instruction Manual 2 About this Manual The content in this manual is for information purposes only and is subject to change without notice. While
More informationGSM RFID VOICE Alarm System
GSM RFID VOICE Alarm System User s Manual For a better understanding of this product, please read this user manual thoroughly before using it. CONTENTS [Function Instruction] [Control Panel] Control Panel
More informationE529 Smart Digital Thermostat Product Guide
E529 Smart Digital Thermostat Product Guide Table of Contents Table of Contents... Page 1 Overview and General Concept... Page 2 Application... Page 3 Features... Page 4 LCD Item Descriptions... Page 5
More informationix30 Zwave PIR Sensor
ix30 Zwave PIR Sensor I. Introduction X30_ZWAVE wireless PIR sensor adopts latest detection & induction technologies including Energy Accumulation Management, Dynamic Random Time Division Technology etc.
More informationCampers Alert TM Portable System Hunters Alert TM Portable System
Campers Alert TM Portable System Hunters Alert TM Portable System USER MANUAL READ THIS ENTIRE MANUAL PRIOR TO INSTALLATION AND OPERATION We thank you for purchasing this Driveway Alert System. All our
More informationREAD ME FIRST DIY WIRELESS ALERT. Add-on Alert Sensor. For Swann Wireless Alert systems. Instruction Manual
READ ME FIRST DIY WIRELESS ALERT Add-on Alert Sensor For Swann Wireless Alert systems EN Instruction Manual 2 About this Manual The content in this manual is for information purposes only and is subject
More informationHX-80NRAM. High Mount Outdoor Detector
Battery operated with 2 PIRs and HX-80NRAM anti-masking Battery operated Battery saving logic Compatible with most wireless transmitter Long distance detection area (24.0 m) Flexible detection area setting
More informationISC-PDL1-W18G-H. Installation Instructions Professional Series Dual Detector
ISC-PDL1-W18G-H EN Installation Instructions Professional Series Dual Detector 1.0 General Information 1.1 Unlock and remove the cover The ISC-PDL1-W18x Professional Series TriTech Detectors are exceptionally
More informationFlash 3 times per 3 seconds: Under voltage indication, please
VOH1007 VOH1007 is a high performance wireless pet immunity P.I.R. motion detector. It consists of digital dual-core fuzzy logic infrared control chip and intelligent analysis which effectively identify
More informationPhotoelectric Beam Detector
Photoelectric Beam Detector ANTI-CRAWL HIGH SECURITY PHOTOBEAM Model: vg-2t30, vg-2t60, vg-2t100 Built-in Rechargeable Lithium-ion Battery Anti-Interference IP65 Weatherproof Environment Adaptive Fully-Sealed
More informationINFRARED PERIMETRAL BARRIER DOUBLE BEAMS
INFRARED PERIMETRAL BARRIER DOUBLE BEAMS 1 MAIN COMPONENT LIST Pag. 3 2 SUGGEST FOR INSTALLATION Pag. 5 3 INSTALLATION Pag. 6 WALL MOUNTING Pag. 6 POLE MOUNTING Pag. 6 4 CONNECTIONS AND DESCTIPRIONS Pag.
More informationPRODUCT DIAGRAM PACKAGE CONTENTS
PRODUCT DIAGRAM PACKAGE CONTENTS After receiving the product, please inventory the contents to ensure you have all the proper parts, as listed below. If anything is missing or damaged, please contact Monoprice
More informationInstallation Instructions
Indoor/Outdoor PIR Motion Sensors 466-1534G August 2006 Copyright 2006, GE Security Inc. Introduction This is the GE Indoor/Outdoor PIR Motion Sensors Installation Instructions for model numbers: 60-639-95R
More informationFitting instructions
Fitting instructions Ver. 02_English 02. 11. 2017 CONTENT 1 INTRODUCTION... 3 2 FITTING THE PATRIOT EU... 3 2.1 Electronic diagram... 3 2.2 Fitting instructions... 4 2.3 Final placement... 4 2.4 Alarm
More informationConsultant Specification AGILE Wireless Fire Detection System
Contents Scope of Work... 2 The EN54 Part 2 & 4 Fire System... 2 Standards... 2 Wireless Intelligent Photoelectric Smoke Detector Specification... 4 Wireless Intelligent Thermal Heat Detector Specification...
More informationWith Magictrl, you can control MatiGard anytime & anywhere via your smartphone, even without data network.
MatiGard User Guide 02 Menu Feature-------------------------------------------------------------- 05 Overviews---------------------------------------------------------- 07 Read Before Using-----------------------------------------------
More informationTo activate using remote control: press [ ] key once. To activate using keyboard: on panel keyboard [ ] keys once.
Table of Content 1.1General Description----------------------------------------------------------------------2 2.2System Setup-----------------------------------------------------------------------------3
More informationPET IMMUNE PIR MOTION DETECTOR
SP815 PET IMMUNE PIR MOTION DETECTOR The SP815 is a multifunction device with motion detector and temperature/humidity sensor. It uses Passive Infra-Red (PIR) technology to detect movement in a protected
More information2G & 3G GSM Portable PIR Alarm
2G & 3G GSM Portable PIR Alarm www.gsm-activate.co.uk MODEL RF - PORTABLE-PIR PAGE 1 Product Information Our 2G/3G Portable PIR Alarm is a standalone alarm system suitable for indoors or outside usage.
More informationSensor : IRA-S210ST01 Lens : IML-0685/0688 Pyro Electric Infrared Sensor Fresnel Lens Features Applications Excellent S/N Intrusion Detectors
Sensor : IRA-S210ST01 Lens : IML-0685/0688 Pyro Electric Infrared Sensor Fresnel Lens Features Excellent S/N Low voltage operation available Applications Intrusion Detectors Lighting Automation Please
More informationGSM Based Computer Lab Security System Using PIR Sensors
Available Online at www.ijcsmc.com International Journal of Computer Science and Mobile Computing A Monthly Journal of Computer Science and Information Technology ISSN 2320 088X IMPACT FACTOR: 6.017 IJCSMC,
More information"Pegaso" wireless alarm system
"Pegaso" wireless alarm system Summary Page 1.0. Description... 2 2.0. Installation... 3 3.0. Connections to mains power... 4 4.0. Low battery signalling... 4 5.0. Service key... 5 6.0. Selection of functions...
More information