CONVENTIONAL FIRE ALARM CONTROL PANEL Model: ARTON-08F

Transcription

1 ISO 9001:2008 CONVENTIONAL FIRE ALARM CONTROL PANEL Model: ARTON-08F OPERATIONAL MANUAL Private enterprise "ARTON" 6 Prutska street Chernivtsi Ukraine EN 54-2 EN 54-4 For further information please contact us:

2 CONTENTS 1 INTRODUCTION PANEL FUNCTIONS TECHNICAL SPECIFICATI ONS ITEMS SUPPLIED WITH THE PANEL DESIGN AND OPERATION Design Operation General overview Access levels Programming possibilities Alarm loops (AL) P rogrammable outputs «AUX1» and «AUX2» Relay outputs «Relay1» and «Relay2» Main modes of operation General overview FIRE mode FAULT mode DISABLEMENT mode ATTENTION mode A LARM mode SAFETY ISSUES COMMISSIONING Mounting Zone wiring Sounder circuit wiring Mains wiring Battery wiring Controlling the panel (authorized user mode) General overview To enable /disable zones To reset zones, FIRE, FAULT and ALARM modes To disable /restore sounders To disable/restore FIRE output To disable/restore FAULT output To check indicators To exit authorized user mode PROGRAMMING GUIDE General overview To enter Programming mode To exit Programmable mode View and change parameters. General overview Section [11n] [22n] Configuring AL Sections [231] Activation conditions of output «SND1» [241] Activation conditions of output «SND2» [311] Activation conditions of output «AUX1» [321] Activation conditions of output «AUX2» [331] Activation conditions of «Relay1» [341] Activation conditions of «Relay2» Sections [232] Zone list for activation of output «SND1» [242] Zone list for activation of output «SND2» [312] Zone list for activation of output «AUX1» [322] Zone list for activation of output «AUX2»

3 [332] Zone list for activation of «Relay1» [342] Zone list for activation of «Relay2» Sections [233] Active time of output «SND1» [243] Active time of output «SND2» [313] Active time of output «AUX1» [323] Active time of output «AUX2» [333] Active time of «Relay1» [343] Active time of «Relay2» Sections [234] Mode of output «SND1» [244] Mode of output «SND2» [314] Mode of output «AUX1» [324] Mode of output «AUX2» [334] Mode of output «Relay1» [344] Mode of output «Relay2» Sections [411] Function of output «AUX1» [412] Function of output «AUX2» [413] Function of output «Relay1» [414] Function of output «Relay2» Sections [431] Access code change of authorized user [432] Access code change of authorized user [432] Access code change of authorized user [432] Access code change of authorized user [441] Engineer access code change Section [421] Control of auxiliary back-up power supply Section [442] Resetting to factory defaults Recording of zone stanby current Output load control Resetting engineer access code to factory defaults Factory default settings GUARANTEES OF MANUFACTURER (SUPPLIER) ACCESSORIES PACK LIST MAINTENANCE APPENDIX APPENDIX APPENDIX APPENDIX APPENDIX APPENDIX USER'S GUIDELINES QUALITY CONTROL CERTIFICATE

4 1 INTRODUCTION 1.1 The manual describes the functions, technical specifications, installation, programming, operation of the ARTON-08F fire alarm control panel (hereinafter panel). 1.2 You should read the manual carefully before installation, adjustment, programming and commissioning the panel. 1.3 This panel must be installed, adjusted and programmed only by a suitably skilled and technically competent person. 1.4 The following abbreviations apply in the manual: BAT rechargeable battery; MCU main control PCB; KIU indications and controls PCB; PSU power supply PCB; Charger backup power charger; S/C short-circuit; O/C open-circuit; Panel ARTON-08F fire alarm control panel; Communicator alarm notification transmission device; FMS fire monitoring station; Zone, ZN fire alarm zone (for the purpose of this manual AL equals to Zone); AL alarm loop. 2 PANEL's FUNCTIONS 2.1 The panel has been designed for the centralized and stand-alone protection of premises against fires by continuous control of up to 8 zone statuses. 2.2 The panel complies with the requirements of EN54-2:2003, EN 54-4:2003. The panel is intended for continuous operation in premises under the following environmental conditions: operating temperature range from 5 to 40 С; relative air humidity up to 95 % at 40 С; atmospheric air pressure kpa. 2.3 The panel can be connected with 2- and 4-wire alarm loops. 2.4 Detectors both increasing and decreasing zone current can be used with the panel. 2.5 Active detectors produced by ARTON can be wired to a panel s loop without current limiting resistors. 2.6 The panel is used to identify and display the following AL statuses: - Standby mode, - ATTENTION, - FIRE, - Fault S/C, - Fault - O/C, - Fault exceeding compensation limit (1) ; - Fault detector s sensor failure (1) ; - Fault detector s system error (1) ; 5

5 - AL disabled. (1): When using intellectual smoke detectors ELITE series produced by ARTON. Note: The ATTENTION status is issued upon detector s first triggering if AL operation algorithm is with verification, or with two detectors wait-to-trigger. 2.7 The panel identifies and indicates the following fault types and statuses for outputs, power supply and the panel in general: S/C in load circuit at outputs enabling; open load of disabled outputs SND1, SND2, FIRE, FAULT (open load monitoring for AUX1, AUX2 can be enabled when you configure the panel); - failure of voltage powering outputs and AL; mains failure; critical discharge or rechargeable battery absence; battery fault; battery fault; charger fault; auxiliary back-up power supply fault; system error. 2.8 When the panel s lid has been opened by an unauthorized user or if the wrong access code has been entered 4 times the panel goes into the alarm condition and issues notifications for FMS. 2.9 The panel issues signals with the following outputs (Bold font - the output names on MC): SND1 first sounder output (up to 300 ma); SND2 second sounder output (up to 300 ma); FIRE FIRE signal output (up to 300 ma); FAULT AULT signal output (up to 300 ma); AUX1 first programmable output (up to 300 ma) (default: 4-wire AL power output); AUX2 second programmable output (up to 300 ma) (default: 4-wire AL power output); 12V auxiliary devices power output (up to 300 ma) with S/C protection; Relay1 first programmable relay (default: enabled in the FIRE mode); Relay1 second programmable relay (default: disabled in the FAULT mode). Each programmable output or relay can be flexibly set by different activation conditions The panel allows to make independent authorized disabling/enabling of any AL as well as short-term resetting of all AL The panel provides automatic charging of BAT and protection against incorrect wiring BAT will be disabled when the battery voltage drops lower than final discharge voltage (10,5V) The panel provides protection of all outputs against S/C with automatic restoration of the initial status after S/C clearing The multilevel access to controls is provided according to the requirements of EN54-2:

6 2.15 The panel provides installing, connecting and status indicating of the BSKT-1 and BSKM-1 communicators (produced by ARTON) The panel provides communication with computer through the BSPC-1 link module The panel ensures connection with communicators from the other manufacturers through the RS-485 interface The panel allows connecting and monitoring of auxiliary back-up power supply to increase stand-alone time of operation The following parameters and functions can be programmed and viewed from the built-in keyboard: - AL operation algorithm (with verification, general, 2 detectors trigger); - AL type (active, passive, combined, ARTON-DL, ELITE); - record of AL baseline standby current (1) ; - zone reset time; - time of verification or waiting for 2 nd detector trigger; - increase current threshold in AL to detect active detector trigger; - decrease current threshold in AL to detect passive detector trigger; - setting of output functions; - setting of output mode; - setting of output activate time; - setting of output activation conditions according to the panel s status and the totality of certain AL statuses on logic conditions AND/OR; - setting of ways to monitor each output load; - setting of user rights on AL control; - access codes of users and engineer; - resetting to factory defaults. (1) : Only if needed. The panel provides automatic record and periodical adjustment of baseline standby current; 3 TECHNICAL SPECIFICATIONS 3.1 The panel is 220 (+22-33) V mains-powered with frequency of (50±1) Hz and/or 12 V sealed non-spillable lead-acid rechargeable battery powered, with a 7/7.2 A/h nominal capacity and 10,5 V terminal voltage of long-lasting discharge (battery is not supplied with the panel). 3.2 Max mains power consumption 25 W. 3.3 Standby mains power consumption 12 W. 3.4 Max BAT current consumption 1,2 А. 3.5 Max BAT standby current consumption 0,2 А. 3.6 Max BAT current consumption at disconnected mains power and BAT voltage < (10,5-1) V 0,01 mа. 3.7 Voltage on open output contacts at total output load < 1,0 A is from 9,0 to 13,8 V. Double pulsation amplitude does not exceed 0,5 V. 3.8 Max voltage on disabled outputs at 3,3 kohm load resistance (with resistors supplied with the panel) - 1,0 V. Note. Presence of the voltage is connected with the need to control output loads. With real loads (e.g., relay winding) the voltage is close to zero. 7

7 3.9 Max number of loops Supply voltage on AL1-AL8 contacts at load absence 15 (±0,5) V. AL1-AL8 voltage at 40 ma in each AL - 12 V Total line (wire) resistance of AL not considering EOL resistor is <220 Ohm Leakage resistance between AL lines (with disabled EOL resistor), and also between each AL line and enclosure - 50 kohm Min current change in AL circuit (relatively to recorded standby AL current) interpreted by the panel as FIRE - plus 4 ma or minus 2 ma (by default). The thresholds can be changed from 1 to 16 ma in increments of 1 ma in programming mode AL current interpreted by the panel as O/C from 0 to 3 mа Max AL current > 60 mа The panel has protection against S/C in AL circuits and outputs with fault indication Up to 32 active detectors can be connected to each loop (SPD-3, SPD-3.5, SPD- 3.10, SPT-2B, SPT-3, SP-2, ARTON-DL etc.), provided that max current consumption by all active fire detectors in the loop does not exceed 3 ma Automatic AL reset period (disablement time) when AL is being verified or manually reset - 5 ±1 sec Detector activation time in Attention mode, on detecting the one the panel goes to FIRE mode - 5 min ±5 sec (by default). It can be set from 5 to 20 min in increments of 5 min Max load current of outputs SND1 and SND2 300 ma; 3.21 Max load current of outputs FIRE and FAULT 300 ma.; 3.22 Max load current of outputs AUX1 and AUX2-300 ma; NB. Total load current of all outputs must not exceed 1.0 A at maximum voltage on outputs Max voltage and current through relay contacts > 30 V, 2A; 3.24 Min current load values of AL in standby mode 3,5 ma (can be set by 3.3 kohm resistors from the accessories pack) Start-up time <10 sec Average mean-time-between-failures - > hs Average lifespan - > 10 years Dimensions 240х300х90 mm Weight without BAT 3,5 kg. 4 ITEMS SUPPLIED WITH THE PANEL 4.1 Having unpacked the panel check the exterior to make sure it is not mechanically damaged and check the contents for completeness that should correspond to Table Note. In accordance with your order the package may contain auxiliary devices expanding the panel s functions. 8

8 5 DESIGN AND FUNCTIONING 5.1 Design The panel consists of the following units: - enclosure; - Main control PCB (MC) with integral transformer board; - rechargeable battery (not supplied with the panel); - Keyboard and Indications PCB (BKI); - terminal block with fuse holder for connection to 220VAC supply; - mains power transformer. The panel s view is shown in Annex 1. For the enclosure s and mounting dimensions refer to Annex 2. The layout of units and PCBs inside the enclosure is shown in Annex 3. The layout and function of outgoing terminals blocks is shown in Annex Operation General overview The panel monitors statuses of 8 fire alarm loops. Depending on the zone current change, panel s condition and program settings, the panel goes to the state with corresponding specific optical indicators light, internal buzzer sounding, enablement of primary and auxiliary sounders, activation of other programmable outputs and relays. Also the panel provides alarm notifications and messages about FMS faults given connected communication appliances. The following statuses are provided by the panel: - «STANDBY»; - «ATTENTION»; - «FIRE»; - «ALARM»; - «FAULT»; - «DISABLEMENT»; - «AUTHORISED USER»; - «PROGRAMMING». Each zone regardless of others can be in the statuses «STANDBY», «FIRE», «S/C», «O/C», «DISABLEMENT», «ATTENTION». The light indicators are located on the front of the enclosure that indicate panel s modes and each loop status (see Appendix 5) Access levels Four access levels are available on the panel. Level 1 general user controls The access of unlimited number of persons is possible on level 1. The following controls are available on the level: testing of all LEDs and internal sounder (by pressing three times on the Test button); silencing the internal buzzer in Fire, Fault, Alarm modes (by pressing the Buzzer off button). Level 2 authorized user controls 9

9 The user access is limited by actions that do not require the use of a special tool or opening the panel s lid. The authorized user controls can be accessed by entering the access code. Each of 4 users has his unique code. The access code is the character chain from [1] to [8] with length from 1 to 8 characters. The access code is entered with [1] [8] buttons and confirmed by pressing the Select button. For default access codes for all users please refer to Section The following controls are available on the level: resetting Fire, Fault, Alarm, Attention modes; resetting all zones (temporal deenergising of all zones); disabling and enabling of separate zones; disabling and repeated enabling of sounders; disabling and repeated enabling of Fire output signal; disabling and repeated enabling of Fault output signal. Level 3 engineer controls (programming mode) Panel s parameters can be changed on the level. To gain access to the mode enter the engineer access code (factory default - [ ]) and press the Select button. The code is a string of numeric characters from [1] to [8], from 8 to 12 digits. Level 4 maintenance level Special auxiliary hardware and software are involved here (used at the factory or service centers) Programming possibilities The following objects can be configured in the programming mode: AL - AL type («Active», «Passive», «Combined», «ARTON-DL», «Elite»); - AL operation algorithm («With verification», «Without verification» «Two detectors»); - Record of each zone baseline current (if necessary, see. p.8.12); - Time of zone readiness after resetting or enabling (a value from the string 3 sec, 5 sec, 10 sec, 15 sec, 20 sec, 30 sec, 40 sec) - Zone verification time (a value from the string 5 min, 10 min, 15min, 20min); - Current growth threshold in a zone to determine an active detector trigger (from 1 to 16 mа in 1mA increment); - Current drop threshold in a zone to determine a passive detector trigger (from 1 to 16 mа in increment of 1 ma); Programmable outputs «AUX1» and «AUX2» - Functions of the outputs «AUX1», «AUX2» (4-wire zone power output (by default), additional sounder output or +12V auxiliary device power output); - Modes of the outputs «AUX1» and «AUX2». This parameter defines the outputs status in active and passive states; - Active time of the outputs «AUX1» and «AUX2» (from 2 sec to «no limit»); 10

10 - Activation conditions of outputs in the sounder mode (response to the status «FIRE», «FAULT» and/or «ATTENTION» in a zone, response to the general FAULT state); - Zone list involved in the activation condition of an output on AND/OR; - Types of output load control (only «S/C», only «O/C», «S/C» and «O/C», without load control). Relay outputs «Relay1» and «Relay2» - Relay modes. The parameter determines the relay status in active and passive states; - Relay active time (from 2 sec to «no limit»); - Relay activation conditions (response to the «FIRE», «FAULT» and/or «ATTENTION» in zone, реакция response to the general FAULT state); - Zone list involved in the activation condition of an output on AND/OR. Sounders (outputs «SND1» and «SND2») - Modes of the outputs «SND1» and «SND2». The parameter determines the output status in active and passive states; - Active time of the outputs «SND1» and «SND2» (from 2 sec to «no limit»); - Activation conditions of the outputs in the sounder mode (response to the «FIRE», «FAULT» and/or «ATTENTION» in zone, реакция response to the general FAULT state); - Zone list involved in the activation condition of an output on AND/OR; - Types of output load control (only «S/C», only «O/C», «S/C» and «O/C», without load control). Users - User s access code change (authorized user and engineer). The panel s configuration or parameters of separate zones can be reset to factory default settings in the programming mode. For the detailed description of the programming mode please refer to Section Alarm loops (AL) The following types of AL can be set on the panel: «Active». The panel responses only to the current growth in AL. The current growth in AL relative to the recorded baseline standby current on the established threshold value (see Table 8.1) is interpreted as the detector trigger in the AL. «Passive». The panel responses only to the current drop in AL. The current drop in the AL relative to the recorded threshold value (see Table 8.1) is interpreted as the detector trigger in the AL. Manual call points or 4-wire detectors can operate by the passive detector scheme. «Combined». The panel responses to the drop and growth of AL current on the determined threshold values relative to the recorded standby current. Both active (2- wire current consuming) and relay current reducing can be connected to this type AL detectors. «ARTON-DL». This AL type can be set when you connect (2-wire) the three-mode beam smoke detector ARTON-DL series. The correct mutual functioning of the detector and panel is ensured by that. 11

11 «Elite». This AL type is set when you connect three-mode smoke detectors «Elite» series to the zone. The receipt of coded notifications from the detectors and indication of their faults such as exceeding drift compensation ultimate level, smoke channel fault, system error are provided here. Fault condition of some detectors do not inhibit receiving of the Fire signal from the other detectors in the loop. Operation algorithm of each of 8 zones (type of the panel s response to triggering of detectors in the zone) can be the following: «Without verification». When detectors go to alarm mode sounder outputs get activated, the corresponding zone and the panel go to the FIRE mode, the FIRE notification is transmitted to FMS; «With verification». When a detector goes to alarm state the zone goes to the ATTENTION mode, the zone is deenergised for a while ( by default 5 sec) including the outputs set as 4-wire zone power outputs. After the power is applied again within the determined time (by default 5 min) the zone state is activated in such a way that the detector trigger in the zone shall invoke the panel going to the FIRE status, otherwise the zone shall go to standby mode. The zone type «With verification» is recommended for protection against false alarms. «Two detectors». When a detector goes to alarm state the zone goes to the ATTENTION mode, and within the determined time waits for the second detector triggering in the zone. If within the determined time (by default 5 min) the second detector triggers in the zone, then the zone shall go to the FIRE status, otherwise when the waiting time is over the zone shall be automatically reset and the zone shall go to standby mode. NB. To ensure the correct functioning of the zone with the operation algorithm fit a current limiting resistor in each detector s base in accordance with the diagrams shown in Appendix 6, and if necessary, increase the threshold of trigger detection at zone current growth Programmable outputs «AUX1» and «AUX2» Each of the programmable outputs «AUX1» or «AUX2» independently of each other can operate as: - 4-wire power output; - Auxiliary sounder output (by activation conditions); - «Two zone fire» output; - «Fault» output; - «Alarm» output; - Non-commutated power output of auxiliary devices (+12V, 300mА, S/C proof). For the output set as 4-wire power output, the list of those zones that will be powered by the output can be specified. In this case when you reset the zone included to the list the other zones included to the list will be automatically reset. For an output set as the auxiliary sounder output, the list of those zones that will be involved in activation of an output with operation logics on AND/OR taking into account the activation conditions can be specified. 12

12 Besides this, a bunch of from 1 to 7 activation conditions can be used to activate the output: - «Attention» in a zone from the programmed list; - «Fire» in a zone from the programmed list; - «Fault» in a zone from the programmed list; - «Fault» of the panel; - «Fault of primary power source (220V)»; - «Fault of back-up power source (BAT)»; - «Alarm» of the panel». Example. One of outputs can be programmed, e.g. «AUX1», with the following activation condition: AUX1 =( Fire[ZN1] AND Fire[ZN2]) OR Fire[ZN3]. The output will get active provided that two zones ZN1 and ZN2 or one ZN3 will go to the FIRE status. An output type «Fire in two zones» activates in the case when two zones from the zone list specified in the programming mode for the output will go to the FIRE mode Relay outputs «Relay1» and «Relay2» Programmable relays «Relay1» and «Relay2» are designed to generate outcoming signals by N.C. or N.O. switchgroups on different activation conditions. The programming possibilities of relays coincide with those of the outputs «AUX1» and «AUX2». NB. By default, «Relay1» is enabled when the panel goes to the Fire mode, the «Relay2» is enabled when the panel goes to the Fault mode. 5.3 Main modes of operation General overview The panel can be simultaneously in the FIRE, ATTENTION, FAULT, ALARM, DISABLEMENT modes, which are indicated with various LED light, the internal buzzer sounding and statuses of outputs. Depending on the panel s mode LED illumination differs with colour, frequency of flashes, and porosity (repetition period/ illumination time). The panel provides different sounding of the internal buzzer in FIRE, ATTENTION, FAULT, and ALARM modes. Enabling of the corresponding general indicators of modes and zone indicators coincides on frequency and phase in FIRE and FAULT modes. For the detailed description of light and sound indication of all statuses and modes of the panel please refer to Appendix «FIRE» mode In the FIRE mode the appropriate zone indicators and General Fire indicator synchronically pulse red, the internal buzzer issues the Fire signal, the FIRE output activates, the sounder outputs SND1 and SND2 activate. Also under the appropriate settings the outputs «AUX1», «AUX2» and relays «Relay1», «Relay2» activate. Besides this the relevant notifications are issued to be transmitted to FMS. The FIRE mode can be reset by any user in the authorized user mode (after entering the access code) while keeping the Reset button pressed for 2-3 sec until the sound signal ceases. 13

13 5.3.3 «FAULT» mode The general FAULT indicator pulses, the internal buzzer generates the Fault signal and the FAULT output activates in the FAULT mode. The following indicators will flash according to the fault type: «Mains fault» 220 V mains fault; «Back-up fault» back-up power fault (BAT); «Zone 1»..«Zone 8» zone fault; «Sounder» sounder fault; «Fire output» Fire output fault; «Fault output» Fault output fault; «Communicator» communication device fault; «System» system error. You can determine a fault type by the LED light. NB. For the detailed description of light and sound indication of each type fault please refer to Appendix 5. Yet the outputs «AUX1», «AUX2» and the relays «Relay1», «Relay2» can be activated with the appropriate settings. The relevant notifications are issued to be sent to FMS. The FAULT mode is reset automatically (is the fault cause has been cleared) or by any user in the authorized user mode (after entering the access code) while keeping the Reset button pressed for 2-3 sec. After resetting the panel will go to the Fault mode if the fault cause has not been cleared «DISABLEMENT» mode The DISABLEMENT mode is activated resulting from the following user actions in the authorized user mode: - Zone disablement; - Disablement (silencing) of sounders; - Disablement (silencing) of the outgoing «FIRE» signal; - Disablement (silencing) of the outgoing «FAULT» signal; The mode is indicated with steady light of the general indicator DISABLED, as well as the relevant indicators «Zone 1»..«Zone 8», «Sounder», «Fire output», «Fault output» «ATTENTION» mode The panel goes to the ATTENTION mode when the triggering of a detector with the With verification or Two detectors operation algorithm has been detected in a zone. The mode is used to warn about the possible fire in the zone. The red indicator of the relevant zone flashes and the internal buzzer issues the Attention signal (two short recurrent beeps). The outputs configured to the response to the Attention status also activate in the mode. The panel also generates the relevant notifications to be sent to FMS. The ATTENTION mode is reset automatically upon the verification time expiring (by default 5 min), if within the time the zone has not gone to the FIRE mode. 14

14 5.3.6 «ALARM» mode The panel goes to the ALARM mode when the panel s lid has been unauthorisingly open. The Alarm indicator flashes red, the internal buzzer issues the alarm signal and the sounder outputs «SND1» and «SND2» or relays configured to response to ALARM status activate. The appropriate notification to FMS is issued. The ALARM mode is reset upon the correct code entering by any user. The panel s lid opening doesn t result to going to the Alarm mode upon the user code entering. 6 SAFETY ISSUES 6.1 Attention! All operations with the panel must be made by operators (users) with the closed panel s lid. 6.2 The installation, mounting, connection and maintenance must be performed by the competent service personnel. 6.3 It should be kept in mind that the 220 V mains voltage in operating state is connected to input terminals that is dangerous for human life. 6.4 The installation, removing, wiring and repair of the panel should be made when the A.C. mains is off. 6.5 The mounting works with the panel should be done using an electrical tool with the voltage not more than 42 V and power not more than 40 W with healthy isolation of current leading circuits from the electrical tool housing. 6.6 The fire safety rules should be kept when performing works with the panel. 6.7 The use of the panel without earthing its enclosure is forbidden. 6.8 The use of the panel in premises with aggressive admixtures causing corrosion is prohibited. 7 COMMISSIONING 7.1 Mounting Decide on the height convenient for mounting and maintenance according to the construction regulations. The panel can be wall-mounted. Mark the holes on the surface the panel is to be mounted to in accordance with the mounting dimensions (Appendix 2). Wires and cables must only be brought through holes in the bottom section of the enclosure (Appendix 3). All the further wirings must be made with the enclosure s lid open. To prevent the panel from going to the FAULT mode when the panel is switched without regular loadings fit 3,3 kohm resistors (supplied in the accessories pack) parallel to terminal blocks of all zones and the outputs «SND1», «SND2», «FIRE», «FAULT». 7.2 Zone wiring Connect alarm loops to the connections «Zone1»..«Zone8» and «GND». The plus wire of a loop connect to the connection «+», and the minus one to the connection «GND» (see Appendix 4). The type and algorithm of loop operation different from the factory defaults are configured in the programming mode. Default programming settings of the panel can be 15

15 found in p The maximum AL resistance not considering EOL resistor must not exceed 220 Ohm. Typical wiring diagrams (2-wire, 4-wire, active, passive, combined) are shown in Appendix 6. The panel automatically records baseline standby currents of all ALs in 10 sec after the panel s enablement. 7.3 Sounder circuit wiring Connect sounders to the outputs «SND1» and «SND2». The plus wire of the loop connect to the connection «+», and the minus one to the connection «GND» (see Appendix 4). 12 V 300 ma sounders and beacons (strobe lights) can be connected to each output. To control line integrity with sounders fit terminal resistors rated from 1 to 5,1 kohm in the end of the line. 7.4 Mains wiring Attention! The connection of the mains power supply to the panel must only be carried out by a suitably qualified service personnel The panel can be wired to the mains supply only using the diagram with differential protective relay in the main distribution board Connect the terminal of the terminal block to grounding mat rated at not greater than 4 Ohm Check for presence and proper operation of 1.0 А fuse in the terminal block Connect the dead power cable to terminals «220 V» so that the phase wire would be connected to «L» terminal and the neutral wire - to terminal «N». Fix the cable using a plastic clip Apply power to the panel. Upon that the test is carried out within 10 sec. During the interval all LED indicators shall be lit a few times and a short signal of the internal buzzer shall sound. The panel also checks program and non-volatile memory, initiates configuration, checks for the faults in outputs, AL and power supply system. When in the course of testing any fault is detected, the general Fault indicator pulses and the internal buzzer turns on (one short and two long signals). When the test is complete the panel produces 3 short sound signals and goes to the standby mode if there are no faults. If after applying the mains supply none of the indicators are not lit check for presence and correct operation of the fuse in the terminal block. 7.5 Battery wiring Caution. You must connect the battery after applying the mains power Position the rechargeable battery as shown in Annex 3. Connect the black wire with the minus terminal, the red wire with the plus terminal of the battery. You must keep the polarity in mind while connecting the battery Close the panel s lid. Upon that only green POWER indicator shall be lit Check the indicators and the internal buzzer by short-time pressing the Test button. As a result all indicators shall flash a few times and the internal buzzer shall sound. 16

16 7.6 Controlling the panel (authorized user mode) General overview You can access to control functions of the panel only after entering the access code. Four programmable access codes for 4 authorized users and one programmable engineer s access code are available. To access the mode enter one of 4 access codes. Use the keys [1] [8] and confirm by pressing [Selection]. Upon that if the entered code is correct the Authorized user indicator shall be illuminated and the panel goes to the appropriate mode. To exit the authorized user mode press [Cancel]. The following controls are available on the level: - enablement/disablement of zones; - resetting of the modes FIRE, FAULT, ALARM; - resetting of all zones (temporal deenergizing of all 2-wire and 4-wire ALs); - disablement (silencing) and enablement (restoring) of sounders; - disablement (silencing) and enablement (restoring) of the outgoing signal Alarm (output «FIRE»); - disablement (silencing) and enablement (restoring) of the outgoing signal «Fault» (output «FAULT»); - checking of LED indicators and internal buzzer for proper operation To disable/enable zones Keep pressed the button of the relevant zone for 2 sec to disable and then to enable a zone. You shall hear the continuous sound signal. Keep the button pressed until the sounding is ceased. After the disabling the indicator of the disabled zone and the general indicator DISABLED shall be steadily lit. Also as a result of the disabling of the zone the FAULT output activates (is disabled). After deenergizing of the panel and then applying power the status of the disabled zones retains. Disablement/enablement of zones by a user is impossible if the user is not entitled to control the zones. User rights to control separate zones can be set in the programming mode using the BSPC-1 computer coupler. By default users have rights for all zones To reset zones, FIRE, FAULT, and ALARM modes To reset FIRE, FAULT, and ALARM modes press [Reset] and keep the button pressed for about 2 sec in the authorized user mode. You shall hear the continuous sound signal while keeping the button pressed. Keep it until the sound ceases To mute/ restore sounders To disable (mute) the sounders «SND1», «SND2» (as well as the outputs «AUX1», «AUX2» set as auxiliary sounders) press [Sounder] in the authorized user mode. To restore sounders (i.e. to turn on sounders when the panel goes to the Fire or Alarm status) press [Sounder] again. Upon muting when the panel goes to the Fire or Alarm mode sounders do not activate. The sounder disablement status is indicated with the steady light of the general indicator "DISABLED" and the indicator "Sounder"

17 7.6.5 To disable/ restore FIRE output To prevent activation of the Fire outgoing signal (output «FIRE») when the panel goes to the FIRE condition use the output's disablement. While keeping pressed [Test]([Func]) push [2] in the authorized user mode. If you will repeat the actions the FIRE output will be restored, i.e. the Fire signal will be activated when the panel goes to the FIRE mode. The disablement of the Fire outgoing signal is indicated with steady light of the general indicator "DISABLED" and the indicator "Outp. Fire" To disable/ restore FAULT output To prevent activation of the Fault outgoing signal (output «FAULT») when the panel goes to the FAULT condition use the output's disablement. To disable the Fault signal push [3] while keeping pressed [Test]([Func]) in the authorized user mode. If you will repeat the actions the Fault signal will be issued when the panel goes to the FAULT mode. The disablement of the Fault output is indicated with steady light of the general indicator "DISABLED" and the indicator "Outp. Fault". NB: The FAULT output is under 12 V voltage in the disabled state. This is a consequence of the output's inverse logics. The active state of the FAULT output is the low voltage on the output To check indicators To check all light indicators and the integral buzzer press [Test] on access level one or level two. All LED indicators shall flash a few times and the internal buzzer shall sound To exit authorized user mode To exit the authorized user mode press [Cancel] or automatically if within 1 minute no buttons have been pressed. 18

18 8 PROGRAMMING GUIDE 8.1 General information To enter programming mode To gain access to the programming mode enter the engineer access code using the numeric keys [1] [8] (engineer factory default - [1][2][3][4][4][3][2][1]) and confirm the entering by pressing [Select]. Upon the correct entering of the access code two short sound signals of different tones will sound and the indicator "Engineer" will be lit on the panel's front. To reset the entered code prior to the confirmation using [Select], press [Cancel]. After reset you should enter the code from the very beginning To exit programming mode To exit the programming mode press [444] using zone numeric keys and confirm it pressing [Select]. The panel shall go to standby mode provided no faults and disablements are in the system. 8.2 View and change of parameters. General overview Programming the panel means change of an object's parameter values. Objects are zone, output, relay, user etc. All object parameters are located in separate sections/cells every of which has its own code. Objects of the same type with typical parameters for the object are grouped in each section when possible. In general to change parameter value you need to enter a 5-digit numeric sequence on the keypad and press [Select]: Indication of the current value Indication of the new value [section code/cell (3 numbers)] [new value (2 numbers)] [Select]. Example. You need to set operation algorithm AL2 with verification. Enter in the programming mode: [122] [12] [Select] Where: [122] section code/cell, and [12]- new parameter value Note: When you press [Cancel] at any place of the entering the whole entered sequence will be cleared. After you have entered the section (cell) number, the 2-digit parameter value code will be indicated with successive flashes of zone indicators [1]..[8]. The selected parameter value can be defined by the succession of flashes of separate LEDs. Example. Succession of flashes of indicators [2] and [1] corresponds to the code «21». If while the current parameter value code is indicated you will enter a new permissible code then the indicators will indicate the new value. The correct entering of the new value is confirmed by the short dual-toned sound signal. Entering of impermissible parameter value is indicated by the long-lasting lowtoned sound signal. To save the new parameter value in non-volatile memory of the panel press [Select]. Saving is accompanied with three short sound signals, after that the return to the beginning of programming will be carried out. Going back to the programming mode without saving the changes made occurs when you press [Cancel] or automatically in 1 min if no buttons have been pressed within the time. 19

19 In several clauses of the section the service section [443] is mentioned, from where the several special functions are performed such as, e.g., recording of standby current of all zones or setting of specific parameters. For the detailed description of configuring please refer to the appropriate clauses of the section. 8.3 Section [11n] [22n] Zone Configuring Section (n zone number) 11n Parameter value Description Table 8.1 Zone type 11 combined 12 active (by default) 13 passive 14 for connection of ARTON-DL detectors 21 for connection of «Elite» detectors 20 12n 13n 14n 21n 22n Zone operation algorithm 11 Without verification (by default) 12 With verification 13 Two detectors Zone setup time 11 3 sec (by default) 12 5 sec sec sec sec sec sec sec Zone verification time 11 5 min (by default) min min min Threshold of activating detection at zone current growth 11 1,0 mа 12 2,0 mа 13 3,0 mа 14 4,0 mа (by default) 21 5,0 mа 22 6,0 mа 42 14,0 mа 43 15,0 mа 44 16,0 mа Threshold of activating detection at zone current drop 11 1,0 mа 12 2,0 mа (by default)

20 13 3,0 mа 14 4,0 mа 21 5,0 mа 22 6,0 mа 42 14,0 mа 43 15,0 mа 44 16,0 mа Example. Successive entering [215][23][Select] sets the activation threshold at zone current growth - 7 ma. 8.4 Sections [231] activation conditions of output «SND1» [241] activation conditions of output «SND2» [311] activation conditions of output «AUX1» [321] activation conditions of output «AUX2» [331] activation conditions of output «Relay1» [341] activation conditions of output «Relay2» Activation conditions define the list of panel's events leading to activation of the relevant output or relay. An output or relay can be activated when one of several events occurs, their list is given below. To view the actual value of activation conditions enter the section number on the numeric keypad in the programming mode. After that the steady light of red and LEDs [1] [4] will indicate the events involved in the activation of the output. - LED zone 1 mode «Attention»; - LED zone 2 mode «Fire»; - LED zone 3 mode «Fault» in zone; - LED zone 4 general mode «Fault»; - red LED zone 1 mains fault (220V); - red LED zone 2 back-up power fault (BAT); - red LED zone 3 mode «Alarm»; Example: if after entering [311] (activation conditions of output «AUX1») the indicators [2] and [3] are lit, then the output «AUX1» will activate when the Fire event or any zone fault occurs. To change zone indicators status press the corresponding buttons [1] [4]. To change red zone indicators status press the corresponding buttons [1] [4] keeping [Func]pressed. Successive pressings cause turn-by-turn change of LED illumination (on/off). Pressing [Select] leads to going to the programming mode with saving the new activation condition. Pressing [Cancel] leads to going to the programming mode with resetting the changes made. 8.5 Section [232] zone list for activation of the output «SND1» [242] zone list for activation of the output «SND2» [312] zone list for activation of the output «AUX1» [322] zone list for activation of the output «AUX2» 21

21 [332] zone list for activation of the output «Relay1» [342] zone list for activation of the output «Relay2» If the modes «Attention», «Fire» or «Fault in zone» have been set for an output or relay in their activation condition, then in those sections the zones involved in activation will be set. Example: If the Fire mode has been set in the activation condition of the «AUX1» output then in the section [312] the zones which will activate the output when the panel goes to the Fire mode) will be set. From 1 to 8 zones with the operation logics on "AND"/"OR" can participate in activation condition of each output. After the section number entering the illumination of zone indicators points to the zones participating in activation condition of the output: - steadily lit zone is included to condition on "AND"; - pulsing zone is included condition on "OR"; - not lit zone is not included to activation condition. Example: If after entering [312] (zone list for activation of the output «AUX1») the indicator [1] is pulsing and the indicators [3] and [4] are steadily lit, then the activation condition for the output «AUX1» is the expression: AUX1 = AL1 OR (AL3 AND AL4)). If the Fire mode response is set in the activation condition of the output (section [311]) then in this case the output «AUX1» will be activated when AL1 or both loops AL3 and AL4 will go to the Fire status. To change AL included to the activation conditions press the relevant zone buttons. Successive pressing leads to turn-by-turn change of zone indicator (on/pulsing/off), that corresponds to the logical condition change (AND, OR, AL not included to condition). Pressing [Select] leads to going to the programming mode with saving of the new zone list for the output or relay. Pressing [Cancel] leads to going to the programming mode with resetting of the changed made. 8.6 Section [233] active time of the output «SND1» [243] active time of the output «SND2» [313] active time of the output «AUX1» [323] active time of the output «AUX2» [333] active time of the output «Relay1» [343] active time of the output «Relay2» Active time of the output is the time an output stays enabled (active) within after occurrence of the activation conditions. NB. If within the active time the conditions that invoked the activation of an output disappear, then the output goes to the passive state. To view and change the parameter enter the following succession in the programming mode: 22

22 [section code/cell (3 numbers)] [new time code (2numbers)] [Select] Code of the new value is according to the table. Table 8.2 Code Time value 11 no limit 12 2 sec 13 5 sec sec sec sec sec sec 31 1 min 32 2 min 33 5 min min min min 43 1 hour 44 2 hour Example. Successive entering [323][31][Select] sets active time of the output «AUX2» equaling 1 min. 8.7 Sections [234] Operation mode of the output «SND1» [244] Operation mode of the output «SND2» [314] Operation mode of the output «AUX1» [324] Operation mode of the output «AUX2» [334] Operation mode of the output «Relay1» [344] Operation mode of the output «Relay2» The operation mode defines the physical state of the output or relay in active and passive state. To view or change the parameter enter the following chain in the programming mode: [section code/cell (3 numbers)] [new mode code (2numbers)] [Select] The code of new mode value should be taken from the table below. Table 8.3 Code 11 Current value indication Current value indication Description of the mode passive state disabled active state enabled (by default) New value indication New value indication 23

23 passive state enabled active state disabled (inversion mode) passive state disabled active state pulsing mode (1Hz) passive state enabled active state pulsing mode (1 Hz) Example. Successive entering [234][12][Select] causes the output «SND1» to go to the mode with inversion (code 12). 8.8 Section [411] Function of the output «AUX1» [412] Function of the output «AUX2» [413] Function of the output «Relay1» [414] Function of the output «Relay2» Function of the output or relay determines its general (typical) functionality. To view and change a parameter enter the following chain in the programming mode: Code 11 [section code/cell (3numbers)] [new node code (2 numbers)] [Select] Code of the new value mode is taken from the table. Function of output Power output of 4wire zones 12 User output 13 Sounder output Activation conditions zone list Activation conditions + zone list Activation conditions + zone list 14 Output «Fire» AL list 21 Output «Fire in 2 zones» AL list 22 Output «Fault» Current value indication Remark New value indication Table 8.4 for powering (+12V) of 4wire zones from the output's zone list Предназначен для питания 4-х проводных ШС из списка ШС для данного выхода (by default for outputs «AUX1» and «AUX1») Output's operation algorithm is defined by the activation conditions and the output's zone list Identical to user output. responses to the commands «Muting/restoring of sounders» Activates when any zone from the output's zone list goes to the Fire mode (by default for relay «Relay1») Activates when any two zones from the output's zone list goes to the Fire mode Activates when the control panel goes to the Fault mode (by default for the relay «Relay2») 24

24 23 Output «Alarm» 24 Secondary power output 31 Output is disabled in configuration Activates when the panel goes to the Alarm mode power output of auxiliary devices (+12V, 300mА max) (identical to the output «+12V») Output is disabled and not analyzedfor faults NB. Functions of the outputs «SND1», «SND2» can be defined by changing the activation conditions and by the zone list for the outputs. NB. Successive entering [414][23][Select] sets the function of the «Relay2» as the output «Alarm» (code 23). 8.9 Sections [431] Access code change of authorized user 1 [432] Access code change of authorized user 2 [432] Access code change of authorized user 3 [432] Access code change of authorized user 4 [441] Engineer access code change To change a user's access code enter the section number in the programming mode. After that using the numeric keys enter a new access code, then press [Select]. Authorized user's code consists of from 1 to 8 digits, engineer's from 8 to 12 digits. [section code/cell (3 numbers)] [new access code] [Select] Example. Successive entering [431][21][Select] sets access code for the 1st user 21. If change of code was successful you will hear 3 short sound signals. To prevent unauthorized control over a zone the change of default access code is recommended Section [421] Control of auxiliary back-up power supply The panel incorporates terminal blocks to connect an auxiliary back-up power supply. With the enabled control the panel analyzes the voltage presence on the inputs «PWR Back+» and «PWR Back Flt». Voltage absence on these inputs or voltage beyond the permissible voltages (10,5 15V) when the control is enabled lead to the panel going to the fault status. To view or change the parameter enter the following chain in the programming mode: Current value indication [section code/cell (3 numbers)] [new value code (2 numbers)] [Select] The code of a new value is taken from the table. Table 8.5 Code Description 11 Control of external power is disabled (by default) 12 Control of external power is enabled New value indication Example. Successive entering [421][12][Select] enables the control of external back-up power supply. 25

25 8.11 Section [442] Resetting to factory defaults This operation resets the panel's configuration to factory defaults indicated in p Enter the section number [442] in the programming mode. After that the delay will be enabled for 10 sec. accompanied with pulsing of the red zone indicators. Confirm your decision about resetting to factory defaults within the time by pressing [Select]. If within the delay none of the buttons (except [Select]) has been pressed then the panel goes to the programming mode without resetting to factory defaults. It is possible to reset the configuration of a separate zone to factory defaults. This operation can be implemented from the service section [443]. Enter the following chain in the programming mode (n zone number): service section code [443] [14n] function code 8.12 Recording of zone standby current Zone standby current is the current value the panel defines the zone current change from, in order to determine the device's activation in zone. The automatic standby current record is provided in the panel. But in certain cases when the big number of devices have been connected to the zone which go to the stable mode of current consumption lingeringly (longer than 10 sec), the manual standby current record is necessary. Manual zone standby current record is performed from the service section [443]. To record standby current of a zone enter the following chain in the programming mode (n zone number): service section code function code [443] [12n] The internal buzzer issues as a result of performing the function: - 3 short sound signals, if setting of zone baseline current has been successful; - 1 long sound signal if the measured zone current is beyond the permissible current range (zone is in S/C or O/C). - To record standby current of all zones enter: service section code function code [443] [111] After implementing of these procedures the panel goes to the beginning of the programming mode. Prior to using this procedure, the zones, the standby current record is being performed for, must be enabled and all detectors in the zones must be in standby mode Output load control All the panel's outputs are S/C proof. Besides that, all the outputs, except for the output «+12V», feature a load control with detecting of O/C in communication line and fault indication. S/C detection enabling/disabling as well as output load presence control (O/C) for every individual output are provided in the panel. The change of output load control is performed from the service section [443]. 26

26 To change load control of an output enter the following chain in the programming mode: service section code [443] [kkk] [nn] [Select] where, kkk cell code of service section, nn new value parameter. The cell code kkk can have the following values: [311] load control of output «FIRE» [312] - load control of output «FAULT» [313] - load control of output «SND1» [314] - load control of output «SND2» [321] - load control of output «AUX1» [322] - load control of output «AUX2» [323] - load control of output «+12V» The new parameter value is taken from the table. Table 8.6 Code Description 11 Only S/C control 12 Only O/C control 13 S/C &O/C control 14 No load control Current value indication New value indication Example. Successive entering [443][314][14][Select] disables the load control of the output «SND2». NB. To ensure load control fit a 1kОhm 5,1kOhm (0,25W) resistor parallel to output load terminals Resetting engineer access code to factory defaults To change engineer access code for the default code [ ], follow the following steps: - deenergise the panel from the 220 V mains and disconnect the battery from the panel; - close the contacts of the MCU "Reset" connector using a jumper (see Appendix 4) and then apply the mains or battery power. On applying power three series of short beeps with long interval between the series shall sound; - remove the jumper, the panel shall be switched on with the factory engineer access code. 27

27 Factory default settings Zone1 Zone8: - type active; - operation algorithm without verification; - start-up time 5 sec; - verification time 5 min; - trigger detection threshold at current growth 4 mа; - trigger detection threshold at current drop 2 mа. Outputs «SND1», «SND2»: - activation conditions Fire and Alarm modes; - zone list zone1 zone8; - active time no limit; - operation mode passive state off, active state on; - load control S/C and O/C detection. Outputs «AUX1», «AUX2»: - type power output of 4-wire zones; - activation conditions not set; - zone list zone1 zone8; - active time no limit; - operation mode passive state off, active state on; - load control S/C detection. «Relay1»: - activation conditions FIRE mode; - zone list zone1 zone8; - active time no limit; - operation mode passive state off, active state on; «Relay2»: - activation conditions general FAULT mode; - zone list zone1 zone8; - active time no limit; - operation mode passive state on, active state off; User access codes: - user 1 [1111]; - user 2 [1112]; - user 3 [1113]; - user 4 [1114]; - engineer [ ]; NB. Each authorized user is entitled to control all zones. Secondary power supply control is disabled. 28

28 9 GUARANTEES OF THE MANUFACTURER (SUPPLIER) The manufacturer warrants the compliance of the panel with the requirements of technical specifications provided the terms of usage, transportation, storage and mounting established by the technical specifications have been kept by the user. The guarantee term is 12 months from the date of commissioning, but not more than 18 months from the date of shipment to the customer s address. 10 ACCESSORIES PACK LIST Table 10.1 No Name Qnty А fuse 2 2 3,3kOhm 0,25W resistor ,4kОhm 0,25W resistor 8 11 MAINTENANCE 11.1 Maintenance must be carried out at least once a year Maintenance works should be fulfilled by staff from a service organization and include: а) examination of the external state of the panel; b) checking for proper operation in accordance with the instructions in Section 7 of the present manual; c) checking how reliable the panel is secured, state of external mounting wires, contact joints; d) checking parameters of the panel's zones and outputs. 29

29 APPENDIX 1 View of the panel's front primary and back-up power supply indicators «POWER», «AC fault» and «BAT fault»; 2 general FIRE mode indicator; 3 general DISABLED mode indicator; 4 general FAULT mode indicator; 5 general ALARM mode indicator; 6 group of indicators for DISABLED and FAULT modes. It turns on the disablement and fault indicators of individual units of the panel: - «Sounder» muting or fault of sounders; - «Fire output» disablement or fault of Fire output; - «Fault output» disablement or fault of Fault output; - «Communicator» disablement or fault of the installed communicator; - «System» indication of system error. 7 indicator of internal buzzer silencing; 30

30 8 button of internal buzzer silencing; 9 button of muting/enabling of sounders; 10 button of FIRE, FAULT modes reset; 11 Test button of indication and internal buzzer; 12 group of indicators for communicator modes It includes disablement and fault indicators of the panel's individual units: - «Transmission» transmission of notifications to FMS; - «Acknowledgment» the acknowledgement about the received notification from FMS has been received. 13 group of indicators for the panel's access level. It includes the following indicators: - «Authorized user» indicator of user identification - (entering access level 2); - «Engineer» engineer identification indicator - (entering access level 3, programming). 14 group of indicators for zone statuses. It includes the following indicators for each zone: - red indicator of the FIRE mode; - indicator of FAULT and DISABLED mode. 15 group of zone controls and access code entry buttons; 16 Cancel button for access code programming; 17 button for access code entry confirmation or for parameter change when the panel is programmed; 18 mounting screw. 31

31 APPENDIX 2 Dimensions

32 1 APPENDIX 3 Layout of PCBs and components of the panel inside the cabinet main control PCB (MCU); 2 «Reset» connector; 3 interface joints for connecting of expansion boards; 4 internal buzzer; 5 wires for battery connection; 6 terminals for connection of secondary winding of the transformer and grounding; 7 terminal block with 0.5 А fuse holder for connection of the panel to the mains; 9 mains transformer; 10 terminals of RS-485 interface and «+12V» output; 11 system joint for the panel connection; 12 KIU joint; 13 terminals for connection of alarm loops; 14 grounding terminals for AL cable screens; 15 holes for cable entry; 16 rechargeable battery; 17 bracket with screw for fastening of BAT. 33

33 34 APPENDIX 4 Main control PCB layout