Open-area Smoke Imaging Detection (OSID)
|
|
- Anne Hudson
- 6 years ago
- Views:
Transcription
1 Open-area Smoke Imaging Detection (OSID)
2 OSID Smoke Detection Open-area Smoke Imaging Detection (OSID) by Xtralis is a new innovation in projected beam smoke detection technology. By using advanced dual wavelength projected beams and optical imaging technology for early warning smoke detection, OSID provides a low-cost, reliable and easy-to-install solution that overcomes typical beam detection issues such as false alarm incidents and alignment difficulties. Unique Detection Technology The OSID system measures the level of smoke entering beams of light projected over an area of protection. A single OSID Imager can detect up to seven Emitters to provide a wide coverage area. Two innovations in smoke detection technology have been developed for the revolutionary OSID smoke detector: Dual Wavelength Particle Detection The beam projected from each Emitter contains a unique sequence of ultraviolet (UV) and infrared (IR) pulses that are synchronised with the Imager and enable the rejection of any unwanted light sources. By using two wavelengths of light to detect particles, the system is able to distinguish between particle sizes. The shorter UV wavelength interacts strongly with both small and large particles while the longer IR wavelength is affected only by larger particles. Dual wavelength path loss measurements therefore enable the detector to provide repeatable smoke obscuration measurements, while rejecting the presence of transient dust particles or solid intruding objects. Optical Imaging with a CMOS Imaging Chip An optical imaging array in the OSID Imager provides the detector with a wide viewing angle to locate and track multiple Emitters. Consequently, the system can tolerate a much less precise installation and can compensate for the drift caused by natural shifts in building structures. Optical filtering, high-speed image acquisition and intelligent software algorithms also enable the OSID system to provide new levels of stability and sensitivity with greater immunity to high level lighting variability. Operation Status information (Fire Alarm, Trouble and Power) is communicated through the Imager via Status LEDs, dedicated Trouble and Alarm relays, and the Remote Indicator interface. Specific Trouble (Fault) conditions are identified through coded flashes of the Trouble LED. Maximum detection range of 150 m (492 ft) for the OSI-10 Dual wavelength LED-based smoke detection Optical imaging with CMOS imaging chip On-board event log for fault and alarm diagnostics High tolerance to false alarm due to building movement High tolerance to transient dust, steam and intrusion of solid objects Easy alignment with large adjustment and viewing angles No need for precise alignment Tolerant of alignment drift Automatic commisioning in under ten minutes Simple DIP switch configuration Simple and easy maintenance requirements Three selectable alarm thresholds Status LEDs for Fire, Trouble and Power Conventional alarm interface for straightforward fire system integration Listings/Approvals UL ULC FM AFNOR CE - EMC and CPD VdS ActivFire BOSEC An internal heating option is also provided on the Imager to prevent condensation on the optical surface, and a reset input enables an external signal to reset the device. Simple Installation and Maintenance The OSID system consists of up to seven Emitters, for the 45 and 90 Imager units, located along the perimeter of the protected area, and an Imager mounted opposite. Each component can be mounted directly to the surface or can be secured with the supplied mounting brackets. Battery powered Emitters with three or five years battery life are also available to reduce installation time and cost.
3 106mm (4.2 ) OSID Smoke Detection On the Imager, a termination card provides all field wiring terminals, and DIP switches enable the user to configure the detector for particular applications. Alignment of the Emitter is simply achieved using a laser alignment tool to rotate the optical spheres until the laser beam projected from the alignment tool is close to the Imager. The Imager is aligned in a similar way so that its Field of View (FOV) encompasses all Emitters. A Trouble or Fault will be indicated if an Emitter is missing or outside the Imager field of view. The OSID system is highly tolerant to transient dust and dirt and requires little maintenance in practice. Preventative maintenance is limited to occasionally cleaning the optical faces of the detector components. The Imagers are equipped with an onboard event memory for diagnostic purposes. Connecting the OSID Diagnostic tool allows users to download this memory log for further alarm and fault analysis and troubleshooting. Configuration Options OSID systems may be configured to suit a range of detection spaces by selecting the number of Emitters and type of Imager. Each type of Imager differs by the lens used in the unit, which determines the field of view and range of the system. Imager Field of View Detection Range Max. Number Standard Power High Power of Horizontal Vertical Min Max Min Max Emitters m (98 ft) 150 m (492 ft) m (20 ft) **34 m (111 ft) 12 m (39 ft) 68 m/50 m* (223 ft/ 164 ft) * Distance with OSE-HP-01. ** Maximum Distances measured for the Center Field of View of the Imager. For more details on distances for the Imager, see the OSID Product Guide. Emitter / Imager Dimensions 208 mm (8.2 ) 20mm (0.8 ) 90mm (3.5 ) 4mm (0.16 ) OSI-10 Imager - 7º coverage OSE-HPW OSI-90 Imager - 80º coverage OSE-HP-01 OSE-SP-01 Emitter - Alkaline Battery OSP-001 OSE-SPW Emitter - Standard Power, Wired OSP-002 OSID-INST OSID Installation Kit OSID-WG OSID-EHE Emitter environmental housing IP66 OSE-RBA OSID-EHI Imager environmental housing IP66 OSI-LS OSE-ACF Anti-condensation film for Emitters OSI-RS OSEH-ACF Anti-condensation film for OSID-EHE and OSID-EHI environmental housings 136 mm (5.4 ) Emitter - High Power, Wired Emitter - High Power, Alkaline Battery FTDI Cable 1.5m Laser Alignment tool Wire Guard Spare alkaline battery pack for Emitter units Light shield for Imagers Reset Station 7 Supply Voltage 20 to 30 VDC (24 VDC nominal) Imager Current Consumption Nominal (at 24 VDC): 8mA (1 Emitter) 10mA (7 Emitters) Peak (at 24 VDC) during training mode: 31mA Emitter Current Consumption Wired Version (at 24 VDC): 350µA Std Power, 800µA High Power Battery Version ( VDC): OSE-RBA Built-in Battery: -SP Version: 5-year battery life -HP Version: 3-year battery life Field Wiring Cable Guage 0.2-4mm² (26-12 AWG) Alarm Threshold Levels: Low - Highest sensitivity / earliest alarm: 20% (0.97 db) Medium - Medium sensitivity: 35% (1.87 db) High - Lowest sensitivity / maximum immunity to nuisance smoke conditions: 50% (3.01 db) Adjustment Angle ±60 (horizontal) ±15 (vertical) Maximum Misalignment Angle ±2 Dimensions (WHD) Emitter / Imager: 208 mm x 136 mm x 96 mm (8.19 in. x 5.35 in. x 3.78 in.) Operating Conditions* Temperature: -10 C to 55 C (14 F to 131 F)* Humidity: 10 to 95% RH (non-condensing) Please consult your Xtralis office for operation outside these parameters. IP Rating IP 44 for Electronics IP 66 for Optics Enclosure Status LEDs Fire Alarm (Red) Trouble / Power (Bi-color Yellow / Green) Event log 10,000 events Approvals Compliance Please refer to the Product Guide for details regarding compliant design, installation and commissioning. * Product UL listed for use from 0 C to 37.8 C (32 F to 100 F) Doc _24
4 Light Shield for OSID Imagers Prevents Imager saturation from bright light sources in one-on-one applications Protects Imagers against bright light outside of a 30 viewing angle in oneon-one applications Quick and easy installation Fits all OSID Imagers Application Beam detectors are susceptible to saturation from direct sunlight most often when installed in an East-West direction and when the sun is low on the horizon. Background subtraction techniques and IR and UV filters make OSID far less susceptible to saturation than standard IR beams. OSID will never false alarm due to bright sunlight. However, severe saturation may in some cases affect the Emitter IR and UV signal and cause a fault to be reported. OSI-LS light shield is available for Imagers to prevent saturation from direct or reflected light. The light shield can only be used in end-to-end / one-on-one configurations. The light shield cannot be used in Multi-Emitter applications. The shield is easy to apply and protects against light outside of a 30 viewing angle. The light shield cannot be used in combination with an environmental housing.
5 Light Shield for OSID Imagers Installation The light shield is fitted with self-adhesive tape. To install, remove the backing paper from the adhesive, align the shield as in the photo, and apply force to affix the shield to the eyeball. Material Flame retardant ABS (UL94 Rating V0) Colour Black OSI-LS Light Shield for Imagers Doc _00
6 OSID Environmental Housing for Imagers and Emitters OSID-EH IP66, NEMA 4-4X for use in harsh environments Imager with extra viewing opening for Alarm and Fault LEDS Dedicated entry for OSP-001 FTDI cable Fast and easy installation- entry and exit opening for wiring Protects against dust and water Application Custom designed IP 66, NEMA 4-4X protective and environmental housings protect OSID imagers and emitters from dust and water ingress in industrial environments. The housings are only to be used with 1 on 1 systems. The glazed housings are made of ABS. The glass window causes minimal attenuation of the UV and IR beams. Installation and servicing is extremely easy. The imager housing has two glands for easy wiring. The Emitter housing can be used with both battery powered and 24V wired emitter. To access to the Imagers FTDI socket the lid needs to be removed. A separate cable inlet directly below the FTDI socket is normally sealed but can be fitted with an additional gland supplied with the enclosure for servicing or upgrading the imager. Both the imager and emitter housing have 3 pre-drilled screw connections for fixed mounting of the unit. The imager has an additional glass window at the bottom of the housing to allow the Alarm and Fault LEDs to be seen from below. Where condensation is expected, both housings can be equipped inside with a heater of minimum 5W. Configuration Options OSID-EHI OSID-EHE Minimum Maximum OSI-10 25m (82ft.) 125m (410ft.) OSI-90 5m (16.4ft.) 28m (91.8ft.) Imager environmental housing Emitter environmental housing Material ABS Size 241x194x127 mm (9.64x7.76x5.08 inch) Colour Grey, RAL 7035 Usage temperature -25 C (-13 F) up to +60 C (140 F) External mechanical resistance IK 07 Doc _03
7 OSID Wire Guard OSID-WG Designed to not interfere with the operation of the protected unit. Fast and easy installation. Simple removal for servicing the units. Constructed from 9 gauge galvanised steel rod. Plastic coated for durability and use in harsh environments. Protects against vandalism or accidental damage Application This steel cage is designed to protect OSID Imagers and Emitters from vandalism and accidental damage. The cage is constructed of heavy gauge steel wire with corrosion resistant polyester coating. Installation and servicing are easy. Highly recommended for areas where abuse to beams is severe in. (104mm) 6.7 in. (167mm) Material: Hard drawn steel wire Thickness: 9 gauge (0.366mm) Diameter Finish: Polyester Powder Coating - Non Carcinogenic Colour: White HMIS: Code-010E 9.2 in. (234mm) OSID-WG Wire Guard for Imager and Emitter Doc _00
8 Anti-Condensation Film for OSID Emitters and EH Housings Application OSID Emitters are equipped with an acrylic lens and are therefore not normally prone to condensation. However in some extremely moist environments, condensation may nevertheless occur on the lens. Slow forming condensation can produce an unacceptably large loss of signal. To prevent that from occurring, the Emitter lens can be fitted with an anti-condensation film. The film can be quickly and easily applied to the lens without the need for special tools or adhesives. Prevents condensation Fast and easy installation Simple maintenance Long lifetime Highly scratch resistant Does not crack, peel or discolour from exposure to sunlight Easy to clean using cleaning solvents The film prevents condensation from forming and keeps the lens clear. Note however that the film causes a 10% reduction in maximum detection distance. A damp cloth can be used to clean the film if it becomes contaminated. The combination of the film and the algorithms in the Imager offer a cost-effective solution for condensation susceptible areas. The OSID Imager has a built-in heater and the film should not be used on Imagers. In harsh environments where the OSID-EH environmental housings are used and condensation is expected, both Emitter and Imager housing can be fitted with an anticondensation film. When applied on Emitter and Imager housing there is a 20% reduction in maximum detection distance.
9 Anti-Condensation Film for OSID Emitters and EH Housings Configuration Options OSE-ACF Min (m/ft) Max (m/ft) HP Min (m/ft) HP Max (m/ft) OSI-10 27/88 135/ OSI-90 5/18 31/100 11/35 61/201 OSI-90 corners - 24/80-49/160 OSEH-ACF (*) Min (m/ft) Max (m/ft) HP Min (m/ft) HP Max (m/ft) OSI-10 19/62 97/ OSI-90 4/13 22/72 8/26 44/144 Material Clear ABC coated polycarbonate Size Diameter 50 mm for Emitter Diameter 120 mm for EH housings Colour Clear, haze < 0.5% Thickness 0.14 mm (*) Film applied on both Imager and Emitter housing. OSE-ACF Anti-condensation film for Emitter OSEH-ACF Anti-condensation film for EH housings Doc _00
Open-area Smoke Imaging Detection (OSID)
Open-area Smoke Imaging Detection (OSID) www.xtralis.com/osid Large, open spaces warehouses, airports, train stations, stadiums and shopping malls pose unique challenges to reliable fire detection due
More informationOpen-area Smoke Imaging Detection (OSID)
Open-area Smoke Imaging Detection (OSID) Large, open spaces warehouses, airports, train stations, stadiums and shopping malls pose unique challenges to reliable fire detection due to their environmental
More informationOpen-area Smoke Imaging Detection (OSID)
Open-area Smoke Imaging Detection (OSID) www.xtralis.com/osid Large, open spaces warehouses, airports, train stations, stadiums and shopping malls pose unique challenges to reliable fire detection due
More informationOpen-area Smoke Imaging Detector. Engineering Specification
Open-area Smoke Imaging Detector 15273_02 October 2011 Table of Contents 1. Scope... 3 2. System Information... 3 2.1 General... 3 2.2 Approvals... 3 2.3 Codes, Standards or Regulations... 3 2.4 System
More informationBeam detector DBD-DL40 KBD-DL80 KBD-DL100
DBD-DL40 Beam detector Beam detector for distances over 5 metres and up to 40 meters, expandable up to 80 or 100 meters with extension kits. Separated head detector and controller for easy access to programming.
More informationOSID in Challenging Environments
OSID in Challenging Environments Application Note March 2013 This page has been left blank intentionally. OSID OSID in Challenging Environments Application Note Table of Contents 1 Scope... 1 2 Dual wavelength
More informationOSID Smoke Detector. Product Guide OSI-10 OSI-45 OSI-90 OSE-SP OSE-SPW OSE-SP-01 OSE-HPW
OSID Smoke Detector Product Guide OSI10 OSI45 OSI90 OSESP OSESPW OSESP01 OSEHPW June 2013 Document No.: 15204 Revision: B Build: 0 Part No. LF42339 OSID by Xtralis OSID Product Guide Intellectual Property
More informationOSID Smoke Detector. Product Guide. July 2011 Document No.: Revision: A Build: 4 Part No. LF42339
OSID Smoke Detector Product Guide July 2011 Document No.: 15204 Revision: A Build: 4 Part No. LF42339 OSID by Xtralis OSID Product Guide Intellectual Property and Copyright This document includes registered
More informationFIRERAY 5000 range USER GUIDE
FIRERAY 5000 range USER GUIDE 0044-003-04 IMPORTANT PLEASE NOTE: The beam path MUST be kept clear of obstructions at all times! Failure to comply may result in the Detector initiating a Fire or Fault signal.
More informationFAAST. Fire Alarm Aspirating Sensing Technology
FAAST Fire Alarm Aspirating Sensing Technology The FAAST range FAAST 8100e FAAST LT PipeIQ Next Generation Aspiration Detection Detection for Challenging Environments 3 in 1 Design, Confi guration and
More informationMulti-Spectral, Digital, Infrared Electro-Optical. FSC Model No. s. Unitized, Two Stage, Quick Response Flame Detectors.
Fire Sentry Corporation (FSC) 593 Apollo Street Tel.: 714-671-1100 Brea, California 92821 Fax: 714-671-5821 Multi-Spectral, Digital, Infrared Electro-Optical FSC Model No. s FS10-R and FS10-A Unitized,
More informationFAAST. Fire Alarm Aspirating Sensing Technology
FAAST Fire Alarm Aspirating Sensing Technology The FAAST range FAAST 8100e FAAST LT PipeIQ Next Generation Aspiration Detection Detection for Challenging Environments 3 in 1 Design, Configuration and Monitoring
More informationTrueAlarm Analog Sensing
TrueAlarm Analog Sensing UL, ULC Listed* Addressable Duct Sensor Housings with TrueAlarm Photoelectric Sensor; Available with Multiple Relay Features Compact air duct sensor housing with clear cover to
More informationOH110, OP110, HI110 Automatic fire detectors
OH110, OP110, HI110 Automatic fire detectors For collective and conventional detector lines Signal processing with detector algorithms Selectable parameter sets 3 color LED indication Drift compensation
More informationDescription. Optex Incorporated
Optex Incorporated Description 1845 W. 205 th St. Torrance, CA 90501-1510 USA TEL (310) 533-1500 and (800) 966-7839 FAX (310) 533-5910 Doc: Model: Desc: Architect/ Engineer Specifications CX-502 PIR Intrusion
More informationI am Rick Jeffress and I handle sales for Fike Video Image Detection. We thank the AFAA for coordinating the venue for this presentation, and we
I am Rick Jeffress and I handle sales for Fike Video Image Detection. We thank the AFAA for coordinating the venue for this presentation, and we appreciate your taking the time to learn more about this
More informationFact File 66. Guide to Beam Smoke Detectors
Fact File 66 Guide to Beam Smoke Detectors Guide to Beam Smoke Detectors INTRODUCTION... 3 TERMINOLOGY... 4 PURPOSE OF BEAM DETECTORS... 5 PROS AND CONS OF BEAM DETECTORS... 6 FUNDAMENTAL PRINCIPLES OF
More informationElite. GJD022 /GJD023 35m External PIR. Multi Beam Lens Data
Elite GJD022 /GJD023 35m External PIR Multi Beam Lens Data The GJD multifunction lens fitted to the GJD Elite detector produces 9 long range beams and 9 medium to short range curtain beams. Movement across
More informationAnaLASER II Detector. Protection Systems. A UTC Fire & Security Company. High-Sensitivity Smoke Detector (HSSD ) FEATURES DESCRIPTION
AnaLASER II Detector High-Sensitivity Smoke Detector (HSSD ) F-89-250 FEATURES Air Sampling Smoke Detector for Early Warning Applications Two Versions Available: Standard Detector and Ultra Detector STANDARD
More informationINSTALLATION INSTRUCTIONS. This model is UL Listed product. The comment with *UL-Number are UL s requirements and information for using this product.
(UL) 9176-13-1 (No. 9176-) INSTALLATION INSTRUCTIONS INSTALLATION AND MAINTENANCE NOTES Warning REDWALL-V series This model is UL Listed product. The comment with *UL-Number are UL s requirements and information
More informationDräger Polytron Pulsar 2 Detection of flammable gases and vapours
Dräger Polytron Pulsar 2 Detection of flammable gases and vapours The Dräger Polytron Pulsar 2 is the latest infrared technology in open path gas detection. Equipped with all the same functions as the standard
More informationHART XL High Sensitivity Smoke Detection
High Sensitivity Smoke Detection The Hart XL High Sensitivity Smoke Detection system (HSSD) is an aspirating fire detection system designed to give very early indication of an incipient fire condition.
More informationIMPORTANT. PLEASE NOTE: The infrared beam path MUST be kept clear of obstructions at all times!
USER GUIDE English IMPORTANT PLEASE NOTE: The infrared beam path MUST be kept clear of obstructions at all times! Failure to comply may result in the Detector initiating a Fire or Fault signal. Contents
More informationMotorised Infrared Optical Beam Smoke Detector. User Guide
Motorised Infrared Optical Beam Smoke Detector User Guide EN 1. General Information 50cm 50cm 8-100m Ensure clear line of sight from Detector to Reflector Mount on solid surfaces (structural wall or girder)
More informationNotifier by Honeywell: FAAST TM Fire Alarm Aspiration Sensing Technology
Notifier by Honeywell: FAAST TM Fire Alarm Aspiration Sensing Technology Notifier by Honeywell: FAAST FAAST Delivers When very early warning fire detection is essential FAAST is a ground breaking aspirating
More informationISC-PDL1-W18G-H. Installation Instructions Professional Series Dual Detector
ISC-PDL1-W18G-H EN Installation Instructions Professional Series Dual Detector 1.0 General Information 1.1 Unlock and remove the cover The ISC-PDL1-W18x Professional Series TriTech Detectors are exceptionally
More informationDräger Flame 2100 Flame Detection
Dräger Flame 2100 Flame Detection Working in areas with combustible gases, vapors, or materials requires fire/ flame detection as a life-saving necessity. The best solutions must combine state-of-the-art
More informationDräger Flame 2500 Flame Detection
Dräger Flame 2500 Flame Detection Working in areas with combustible gases, vapours or materials requires fire/ flame detection as a life-saving necessity. The best solutions must combine state-of-the-art
More informationDT900 Series Sensors TECHNOLOGY FOR LARGE COMMERCIAL AND INDUSTRIAL APPLICATIONS. Impressive Performance, Impressive Coverage
DT00 Series Sensors TECHNOLOGY FOR LARGE COMMERCIAL AND INDUSTRIAL APPLICATIONS Impressive Performance, Impressive Coverage DT00 Series Sensors Building on more than 20 years of dual technology innovation,
More informationReflective Beam Smoke Detector
Reflective Beam Smoke Detector SRA-ET Features! 5-30m range! Small flat reflector! Powered directly from the zone! Full line continuity options! Automatic compensation! Approved by LPCB & VdS Description
More informationTX7130. Conventional Reflective Beam Detector Installation and Operation Manual. TANDA UK Technology Copyright 2015, All right reserved.
TX7130 Conventional Reflective Beam Detector Installation and Operation Manual Technology Copyright 2015, All right reserved. Product Safety To prevent severe injury and loss of life or property, read
More informationFlame Detection Jon Sarfas
Flame Detection Jon Sarfas Agenda Introduction Detection Principles FL4000H MSIR Flame Detector Flame Test Lamp Installation Best Practice Features & Benefits Applications Introduction Primary objectives:
More informationMotorised Infrared Optical Beam Smoke Detector. User Guide
Motorised Infrared Optical Beam Smoke Detector User Guide EN 1. General Information 50cm 50cm 8-100m Ensure clear line of sight from Detector to Reflector Mount on solid surfaces (structural wall or girder)
More informationApollo Intelligent Auto Aligning Beam Detector. User Guide
Apollo Intelligent Auto Aligning Beam Detector User Guide EN 1. General Information 50cm 50cm 8-100m Ensure clear line of sight from Detector to Reflector Mount on solid surfaces (structural wall or girder)
More informationMovement Detector GJD 300
Movement Detector GJD 300 Installation & Set Up Guide Introduction A CCTV event trigger utilising two independent passive infrared detectors combined in a T05 package. Both sensors have to trigger before
More informationNotifier by Honeywell: FAAST TM Fire Alarm Aspiration Sensing Technology
Notifier by Honeywell: FAAST TM Fire Alarm Aspiration Sensing Technology Notifier by Honeywell: FAAST FAAST Delivers When very early warning fire detection is essential FAAST is a ground breaking aspirating
More informationALK-V PHOTOELECTRIC SMOKE SENSOR
ALK-V PHOTOELECTRIC SMOKE SENSOR APPLICATION The HOCHIKI America ALK-V Photoelectric Smoke Sensor is particularly suited to detecting optically dense smoke typical of fires involving materials such as
More informationTrueAlarm Analog Sensing
UL, ULC Approved* TrueAlarm Analog Sensing TrueAlarm Analog Sensors Photoelectric and Heat; Standard Bases and Accessories Features TrueAlarm analog sensing provides: Digital transmission of analog sensor
More informationD-TECT Dual Tech. GJD360 Triple Technology External Detector
D-TECT Dual Tech GJD360 Triple Technology External Detector PACKAGE CONTENTS 1 x Dual Tech 1 x Drilling template for fixing holes 3 x 31.75mm wall plugs 3 x 31.75mm screws 2 x Spare Sliding Curtains 2
More informationGJD OPAL RFX WIRELESS 35 METRE EXTERNAL PIR INSTALLATION MANUAL
GJD OPAL RFX WIRELESS 35 METRE EXTERNAL PIR INSTALLATION MANUAL A WIRELESS PASSIVE INFRARED DETECTOR AND THREE CHANNEL RECEIVER THAT SIMULTANEOUSLY OR INDIVIDUALLY CONTROLS CCTV SWITCHERS, VIDEO RECORDERS
More informationD-TECT Introduction. Connecting the Unit. Quick Installation. Multi Beam Alignment & Masking. Mounting the Unit
D-TECT 2 GJD300 Quad PIR Movement Detector Package Contents Package Contains: 1 x D-Tect 2 1 x Drilling template for fixing holes 3 x 31.75mm wall plugs 3 x 31.75mm screws 2 x Spare Sliding Curtains 2
More informationOH110, OP110, HI110. Automatic Fire Detectors. Automatic Fire Detector For collective and conventional detector lines
Automatic Fire Detector For collective and conventional detector lines Signal processing with detector algorithms Selectable parameter sets 3 colour LED indication Drift compensation Internal fault monitoring
More informationMiniature Infrared Temperature Sensors with Optional Touch Screen Display. PSC-SSS-PM with touch screen display (-CRT version)
PSC-SSS-PM Series Miniature Infrared Temperature Sensors with Optional Touch Screen Display PSC-SSS-PM with touch screen display (- version) FEATURES Miniature sensing head and configurable electronics
More informationLZR -H110. LASER SCANNER FOR BARRIERS & GATES with max. detection range of 5.0 m x 6.5 m (16.5 ft x21 ft) User s Guide
EN LZR -H110 LASER SCANNER FOR BARRIERS & GATES with max. detection range of 5.0 m x 6.5 m (16.5 ft x21 ft) User s Guide 75.5897.02 LZR-H110 20170821 Page 1 of 12 SAFETY The device contains IR and visible
More informationINSTALLATION AND MAINTENANCE INSTRUCTIONS NFXI-BEAM AND NFXI-BEAM-T REFLECTED TYPE PROJECTED BEAM SMOKE DETECTOR
INSTALLATION AND MAINTENANCE INSTRUCTIONS NFXI-BEAM AND NFXI-BEAM-T REFLECTED TYPE PROJECTED BEAM SMOKE DETECTOR GENERAL The model NFXI-BEAM is an addressable long range projected beam smoke detector designed
More informationHART XL High Sensitivity Smoke Detection
High Sensitivity Smoke Detection Hart XL High Sensitivity Smoke Detection (HSSD) TM is a smoke detection system that is simple to install, commission, service and use yet remains brilliantly capable in
More informationDräger Polytron Pulsar 2 Open Path Gas Detector
Dräger Polytron Pulsar 2 Open Path Gas Detector The Dräger Polytron Pulsar 2 represents the latest infrared technology in open path gas detection. Equipped with all the same functions as the standard Dräger
More informationReflective Optical Beam Smoke Detector User Guide
Reflective Optical Beam Smoke Detector User Guide 1. Installation IMPORTANT NOTE: The infrared beam path MUST be kept clear of obstructions at all times! Failure to comply may result in the system initiating
More informationWhy choose Fireray? Why use a Beam Smoke Detector? Product Range.
Range Brochure Why use a? Beam smoke detectors are the wide area smoke detection technology of choice, offering both excellent detection and value for money. With a high area of coverage per unit (as high
More informationCOMPANY PROFILE Technoswitch with its headquarters, manufacturing and training facilities in Johannesburg, has been supplying and providing technical
COMPANY PROFILE Technoswitch with its headquarters, manufacturing and training facilities in Johannesburg, has been supplying and providing technical support for high quality fire detection products into
More informationMulti-Point Peripherals
UL, ULC Approved* Multi-Point Peripherals TrueAlarm CO Sensor Bases for Smoke, Heat, and Photo/Heat Sensors using IDNet Communications Features Fig 1: TrueAlarm CO Sensor Base with Sounder (shown with
More informationInstallation and Operation Manual
[Please read this installation & operation manual before install and use this Installation and Operation Manual Address: 8-701,Dongfangming Industry Zone, Dabao Road., Baoan, Shenzhen, China-518101 Page
More informationExtended Range DUAL TEC Motion Sensor
DT-900 S E R I E S Extended Range DUAL TEC Motion Sensor Building on more than 1 of dual technology innovation, IntelliSense s new generation DUAL TEC DT-900 motion sensor provides the features and technology
More informationINSTALLATION AND MAINTENANCE INSTRUCTIONS 6500R AND 6500RS REFLECTIVE TYPE PROJECTED BEAM SMOKE DETECTOR
INSTALLATION AND MAINTENANCE INSTRUCTIONS 6500R AND 6500RS REFLECTIVE TYPE PROJECTED BEAM SMOKE DETECTOR GENERAL The model 6500R is a conventional long range projected beam smoke detector designed to provide
More informationEnglish. Italiano. Português. Françias. Español
DT AM Grade 3 Español Françias Português Italiano English High Ceiling Mount Detector Installation Guide English DT AM Grade 3 High Ceiling Mount Detector Installation Guide General Description The Industrial
More informationTrueAlarm Smoke Detectors
UL, ULC Approved* TrueAlarm Smoke Detectors TrueAlarm Photoelectric Smoke Detector with TrueSense Smoke/Heat Detection Features detection. If any of these alarm conditions are experienced, an alarm is
More informationD-Tect 2 GJD300 Quad PIR Movement Detector
D-Tect GJD0 Quad PIR Movement Detector Package Contents 3. Package Contains: x D-Tect x Drilling template for fixing holes x Allen Key 3 x 3.75mm wall plugs 3 x 3.75mm screws x Spare Sliding Curtains x
More information4040 FM 535 F :
OVERVIEW OPTICAL TURNSTILE SYSTEM HALF HEIGHT BARRIER TURNSTILES MODEL OTS-HHB-6 The OTS-HHB monitors through-beam infrared sensors, access control contacts, and barrier posion sensors to control the moon
More informationTITLE SLIDE FIRERAY50/100R OPTICAL BEAM SMOKE DETECTOR. Doc. No: Copyright Fire Fighting Enterprises Ltd.
TITLE SLIDE FIRERAY50/100R OPTICAL BEAM SMOKE DETECTOR Doc. No: 32-0008-01 OPTICAL BEAM SMOKE DETECTORS This training material provides information to assist the Fire System Designer and Installer in achieving
More informationFAAST. Fire Alarm Aspiration Sensing Technology
FAAST Fire Alarm Aspiration Sensing Technology European Head Office Life Safety Distribution AG Javastrasse 2 8604 Hegnau Switzerland Tel: +41 44 943 4400 Email: sse.sales@systemsensor.com www.systemsensoreurope.com
More informationModel DRD-AS Conventional Infrared Flame Detector User Manual Ver. 1.0
Model DRD-AS Conventional Infrared Flame Detector User Manual Ver. 1.0 Page 1 of 11 DRD-AS Flame Detector User Manual Table of Contents 1.1 Description... 3 1.2 Alarm Response Modes... 3 1.3 IR Detection
More informationConsultant Specification AGILE Wireless Fire Detection System
Contents Scope of Work... 2 The EN54 Part 2 & 4 Fire System... 2 Standards... 2 Wireless Intelligent Photoelectric Smoke Detector Specification... 4 Wireless Intelligent Thermal Heat Detector Specification...
More informationSmoke Detection Solutions for Challenging Environments
Smoke Detection Solutions for Challenging Environments Agenda The Detection Triangle A Balancing Act Harsh and/or Industrial Environments New advances in Open Area smoke detection Traditional Beam Detection
More informationIntrusion Outdoor Protection Perimeter
Intrusion Outdoor Protection Perimeter Borders Commercial industrial Military base Correctional institution VIP Estates/Residences Communication Airports Warehouses Perimeter Sensors: the ideal solution
More informationINSTALLATION AND MAINTENANCE INSTRUCTIONS 6500 AND 6500S REFLECTED TYPE PROJECTED BEAM SMOKE DETECTOR
INSTALLATION AND MAINTENANCE INSTRUCTIONS 6500 AND 6500S REFLECTED TYPE PROJECTED BEAM SMOKE DETECTOR GENERAL The model 6500 is an addressable long range projected beam smoke detector designed to provide
More informationEvolution Analogue Addressable Fire System
Addressable Fire System optimum fire safety systems solutions High speed FSK protocol, uniquely resistant to noise Up to 254 addresses per loop for flexible system design Built to exceptional marine standards
More information>WIRELESS> ALARM SYSTEM CR200
intrusion >WIRELESS> ALARM SYSTEM CR200 INTRUSION HOME SECURITY CR200 is a Modern, Effective and Versatile 20-zone Household Security System. It is packed with simple Plug & Play functionality, designed
More informationLZR -I30. max. detection range of 30 ft x 30 ft LASER SCANNERS FOR INDUSTRIAL DOORS LZR-I Page 1 of 12
EN LZR -I30 LASER SCANNERS FOR INDUSTRIAL DOORS max. detection range of 30 ft x 30 ft 75.5667.07 LZR-I30 0509 Page of SAFETY The device contains IR and visible laser diodes. IR laser: wavelength 905nm;
More informationInstructions AutroFlame IR Flame Detector BG-201/BG-21
Instructions AutroFlame IR Flame Detector BG-201/BG-21 116-P-BG201-BG21/DGB 2012-10-10 COPYRIGHT This publication, or parts thereof, may not be reproduced in any form, by any method, for any purpose. and
More informationAspirating Smoke Detection PRODUCTS. Accessories Piping Conventional and Intelligent Detectors
Aspirating Smoke Detection PRODUCTS Accessories Piping Conventional and Intelligent Detectors 2 High Sensitivity. Simple Communications. Nuisance Immunity. FAAST Fire Alarm Aspiration Sensing Technology
More informationINSTALLATION AND MAINTENANCE INSTRUCTIONS 6500R AND 6500RS REFLECTIVE TYPE PROJECTED BEAM SMOKE DETECTOR
INSTALLATION AND MAINTENANCE INSTRUCTIONS 00R AND 00RS REFLECTIVE TYPE PROJECTED BEAM SMOKE DETECTOR GENERAL The model 00R is a conventional long range projected beam smoke detector designed to provide
More informationOSI-RI-FL Single-ended Reflected Type Projected Imaging Beam Smoke Detector Intelligent
OSI-RI-FL Single-ended Reflected Type Projected Imaging Beam Smoke Detector Intelligent Installation Guide October 2018 Document No.: E56-6584-001 (33807_01) OSI-RI by Fire-Lite Alarms OSI-RI-FL Installation
More informationMulti-Point Peripherals
Multi-Point Peripherals UL, ULC, CSFM Listed; FM Approved* TrueAlarm CO Sensor Bases for Smoke, Heat, and Photo/Heat Sensors using IDNet Communications Features TrueAlarm addressable CO sensor bases contain
More informationGAS PLUS ALARM SYSTEM
GAS PLUS -IR SERIES 4688-IR COMBUSTIBLE GAS OR CARBON DIOXIDE TRANSMITTER GAS PLUS -IR TRANSMITTER SERIES 4688-IR COMBUSTIBLE GAS OR CARBON DIOXIDE TRANSMITTER The Scott Gas Plus -IR Model 4688 IR Gas
More informationSAFETY MANUAL. X2200 UV, X9800 IR, X5200 UVIR SIL 2 Certified Flame Detectors
SAFETY MANUAL X2200 UV, X9800 IR, X5200 UVIR SIL 2 Certified Flame Detectors SAFETY-CERTIFIED Flame DETECTORs This manual addresses the specific requirements and recommendations applicable to the proper
More informationIntelligent addressable fire alarm control panel
Intelligent addressable fire alarm control panel Input current consumption: Panel rating: Batteries: Networking and Interfaces Panel to panel communication: Number of panels: Interface port: System capacity
More informationSiemens aspirating smoke detector (ASD) for the addressed FDnet/C-NET detector line or for standalone operation
Sinteso Cerberus PRO FDA241, FDA221 ASD Aspirating smoke detector Siemens aspirating smoke detector (ASD) for the addressed FDnet/C-NET detector line or for standalone operation Patented technology Early
More informationM O T I O N DETECTORS. The Paradox series of motion detectors. combines advanced features and patented. technologies to provide a high level of
M O T I O N DETECTORS The Paradox series of motion detectors combines advanced features and patented technologies to provide a high level of detection and false alarm prevention. Whatever the application,
More informationS200Plus Triple Infra Red Flame Detector Triple Waveband Infra-Red Flame Detection
DATASHEET S200Plus Triple Infra Red Flame Detector Triple Waveband Infra-Red Flame Detection Features: Unrivalled black body rejection over a wide range of source temperatures Triple waveband infra-red
More informationDanfoss gas detection units
Data sheet Danfoss gas detection units Types GD Premium, Premium+, Premium Duplex, Premium Remote, Premium Flex and Premium Uptime The Premium line gas detection units are used for monitoring and warning
More informationAnalogue Detectors. Series 200 plus
Analogue Detectors Series 200 plus The world s finest manufacturing facility System Sensor s European products are researched, designed and manufactured at our 10,000m 2 state-ofthe-art facility in Trieste,
More informationTwin Photobeam Detectors Manual
Also available from SECO-LARM: Twin Photobeam Sensors Quad Photobeam Detectors Curtain / Barrier Sensors Twin Photobeam Detectors Manual Up to 390ft (0m) range Laser-beam alignment Anti-frost system Adjustable
More informationSAFEYE XENON 700. Hydrocarbons and ethylene detection. Heated optics. 10-year Warranty for the Xenon flash bulb. SIL 2 according to IEC 61508
Open-Path Gas Detection System SAFEYE XENON 700 Hydrocarbons and ethylene detection Heated optics 10-year Warranty for the Xenon flash bulb SIL 2 according to IEC 61508 Certifications The Fixed Gas Detection
More informationXGUARD-10/-5. LASER SCANNERS for industrial doors. User s Guide for product version 0600 and more
EN XGUARD-0/-5 LASER SCANNERS for industrial doors XGUARD-0: max. detection range of 9.9 m x 9.9 m XGUARD-5: max. detection range of 5.0 m x 5.0 m User s Guide for product version 0600 and more SAFETY
More informationIFD-E Flame Detector User Manual
IFD-E Flame Detector User Manual 2 Hochiki Europe (UK) Ltd General Description The flame detector is designed for use where open flaming fires may be expected. It responds to the light emitted from flames
More informationIntrusion sensors. We listened to you
Intrusion sensors We listened to you Advanced technology, makes it a simple choice Whether you choose Passive Infrared (PIR), Dual or Vector technology, our motion sensors have a number of intrinsic advantages:
More informationSEC Signature Process Gas Analyzer
SEC Signature Process Gas Analyzer Instruction and Operation Manual Sensor Electronics Corporation 5500 Lincoln Drive Minneapolis, Minnesota 55436 USA (952) 938-9486 Fax (952) 938-9617 email sensor@minn.net
More informationPhotobeam 5000 ISC-FPB1-W60QS, ISC-FPB1-W120QS, ISC-FPB1-W200QS. en Installation and Operation Guide
Photobeam 5000 ISC-FPB-W60QS, ISC-FPB-W20QS, ISC-FPB-W200QS en Installation and Operation Guide Photobeam 5000 Table of Contents en 3 Table of contents Introduction 4. About documentation 4.2 Bosch Security
More informationLaserFOCUS VLF-250 Engineering Specification
Vision Fire & Security LaserFOCUS VLF-250 Engineering Specification May 2004 Part Number 20296 LaserFOCUS VESDA 2 VESDA LaserFOCUS Contents Scope...4 Description...4 General...4 Approvals...4 Codes, Standards
More informationSIL725 Safety Annunciator
SIL725 Safety Annunciar Configurable SIL2 Annunciar certified IEC61508 SIRA certified at safety integrity level SIL2 IEC61508 Modular construction from 1 128 alarm channels Multi-redundant design Choice
More informationHigh Mount. Low Mount. High security wired tri-technology external detectors with anti-masking
High Mount Low Mount High security wired tri-technology external detectors with anti-masking XDH10TT-AM Installation height 2.4m High Mount Installation - XDH The XDH detectors optical configuration is
More informationSAFETY MANUAL. FL4000H and FL4000 Multi-Spectral Infrared Flame Detectors
SAFETY MANUAL FL4000H and FL4000 Multi-Spectral Infrared Flame Detectors The information and technical data disclosed in this document may be used and disseminated only for the purposes and to the extent
More informationMR300 OPTICAL SMOKE DETECTOR RANGE PRODUCT APPLICATION & DESIGN INFORMATION
DOCUMENT CONTROL NUMBER / MR300 OPTICAL SMOKE DETECTOR RANGE PRODUCT APPLICATION & DESIGN INFORMATION 1. INTRODUCTION The MR300 range of optical smoke detectors forms part of the M300 series of plug-in
More informationMINERVA S200Plus. Fire Detection. Triple Waveband Infra-Red Flame Detection. Features: Minerva S200PLUS
MINERVA S200Plus Triple Waveband Infra-Red Flame Detection Features: Unrivalled black body rejection over a wide range of source temperatures Triple waveband infra-red solar blind flame detection for optimum
More informationModel 3300 Technical Support and Installation Manual
Model 3300 Technical Support and Installation Manual Manual # T15011 Document Revision: A1 1. OVERVIEW 1 2. BASIC OPERATION 1 2.1 General 1 2.2 Field-of-View 2 2.3 Range 2 2.4 Environment 2 2.5 Configuration
More informationADPRO PRO Series by Xtralis
ADPRO PRO Series by Xtralis Passive Infrared Outdoor Detectors Product Highlights The ADPRO PRO Series by Xtralis PIR detectors are specifi cally designated for intrusion detection Designed and manufactured
More information2 General Application Photoelectric Sensors
SMARTEYE PRO/PRO 2 General Application Photoelectric Sensors Self-Adjusting General Purpose Sensor www.ttco.com 800-237-0946 2-7 General Application Photoelectric Sensors 2 SMARTEYE PRO/PRO The SMARTEYE
More informationAir Sampling Smoke Detection
Air Sampling Smoke Detection Notifier by Honeywell: Data Sheet Air Sampling Smoke Detection Data Sheet The Notifier by Honeywell range of air sampling smoke detection systems (ASSD) comprises smoke detectors
More informationLASER ASPIRATED SMOKE DETECTOR
LASER ASPIRATED SMOKE DETECTOR LASD1 (Single Channel) INSTALLATION, OPERATION & MAINTENANCE INSTRUCTIONS (CE) 1 INTRODUCTION The LASD1 utilises one or two high-sensitivity laser point detectors in an aspirated
More informationWFDE Series Waterflow Detector
WFDE Series Waterflow Detector The System Sensor WFDE series is compatible with pipe diameters ranging from 50mm through 200mm and can be mounted in a vertical or horizontal position. Features Compliant
More information