RECOGNIZED COMPONENT Constructional Data Report (CDR)

Transcription

1 RECOGNIZED COMPONENT Constructional Data Report (CDR) 1.0 Reference and Address Report Number SHA-001 Original Standard(s) Power Units Other Than Class 2 UL 1012 Eighth Edition Dated November 9, 2010 containing Revisions through and including May 14, 2014 General Use Power Supplies CSA C22.2 No Dated September 2001, Reaffirmed 2011 Applicant Manufacturer Address 5F., No.8, Alley 11, Lane 327, Sec. 2, Chung San Road, Chung Ho, Taipei County Address 2F, No.14, Lane 327, Sec. 2, Chung San Road, Chung Ho, Taipei County Country Contact Phone FAX Taiwan Mr. K.C. Huang kc@ieeeg.com Country Contact Phone FAX Taiwan Ms. S.H. Huang shhuang@ieeeg.com Page 1 of 25

2 2.0 Product Description Product Brand name Switching Power Supply AMC Page 2 of 25 Description Models Model Similarity Ratings Other Ratings Conditions of Acceptability The product covered by this report is switching mode power supplies with no power supply provided, it shall be connected to VAC 50/60Hz supply source indirectly. SPS100 NA Input: Vac, 50/60Hz, 2.5A Output: 12Vdc, 10A NA The products covered in this Report are incomplete in construction features or limited in performance capabilities and are intended for use and evaluation in other products. Consideration should be given to the following when the component is used in or with another product. 1) A suitable enclosure that complies with CSA Enclosure 2 (Dripproof) of CSA Standard C22.2 No. 94, should be provided, and the suitability of the enclosure should be considered during evaluation end-use product. 2) The product is only intended for use in a CONTROLLED ENVIRONMENT

3 3.0 Product Photographs Photo 1 - Front view Page 3 of 25 1 Photo 2 - Back view 12

4 3.0 Product Photographs Page 4 of 25 Photo 3 - Internal view 2 Photo 4 - PCB 8 7

5 3.0 Product Photographs Page 5 of 25 Photo 5 - PCB Photo 6 - Back view of PCB 10

6 3.0 Product Photographs Page 6 of 25 Photo 7 - Transformer 9

7 Page 7 of Critical Components Photo # Item no. 1 Name Manufacturer/ trademark 2 Type / model 2 Technical data and securement means Mark(s) of conformity Enclosure 3 2 Appliance inlet Nan Ya Plastics (Hui Zhou) Corp Ltd 4410G4 Yueqing Yanhui DB-14 Electronic Co Ltd Zhejiang Leci Electronics DB-14 Co Ltd Various CONQUER ELECTRONICS CO LTD Various Rated V-0, RTI(150, 130, 130), HWI=0, HAI=3, Min. thick 1.5mm, secured by screws. (E235269) Rated AC250V, 10A, IEC 320 Config: C14. (E334847) Rated AC250V, 10A, IEC 320 Config: C14. (E302229) Rated AC250V, 10A, IEC 320 Config: C14. curus UL, CSA PTU T5A, 250V, (E82636) curus Fuse VDR (VR2) (optional) X Capacitor (CX1, CX2) Y capacitor (CY1, CY2) SHENZHEN LANSON ELECTRONICS CO LTD HONG HU BLUELIGHT ELECTRONIC CO LTD XC ELECTRONICS (SHENZHEN) CORP LTD Thinking Electronic Industrial Co Ltd Shantou High-New Technology Developmnt Zone Songtian Enterprise Co Ltd Shenzhen Surong Capacitors Co Ltd Shantou High-New Technology Developmnt Zone Songtian Enterprise Co Ltd Liaoning Diya Capacitor Co Ltd Europtronic (Taiwan) Industrial Corp Shantou High-New Zone Songtian Enterprise Co., Ltd Hsuan Tai Electronics Co Ltd 3N T5A, 250V, (E221465) curus L3CT, L3T T5A, 250V, (E324232). curus 3T T5A, 250V, (E249609). curus TVR10471K, TVR10511K, TVR10561K, TVR10621K, TVR10681K, TVR14471K, TVR14511K, TVR14561K, TVR14621K, TVR14681K 10D471K, 10D511K, 10D561K, 10D621K, 10D681K, 14D471K, 14D511K, 14D561K, 14D621K, 14D681K MPX MPX MKP-X2 MPX2 Series CD CY Series Rated Min.300Vac. (E314979) Rated Min.300Vac. (E330837) Max. 0.47µF, Min. 275VAC, 100 C, X2 type; (E314875) Max. 0.47µF, Min. 275VAC, 100 C, X2 type; (E208107) Max. 0.47µF, Min. 275VAC, 100 C, X2 type; (E305002) Max. 0.47µF, Min. 275VAC, 100 C, X2 type; (E211347) Max. 1000pF, Min.400VAC, 125 C, Y1 type, 2 pieces. (E208107) Max. 1000pF, Min.400VAC, 125 C, Y1 type, 2 pieces. (E ) curus curus curus curus

8 Page 8 of Critical Components Photo # Item no. 1 Name Manufacturer/ trademark 2 Type / model 2 Technical data and securement means Yinan Don's Electronic Component Co Ltd Shantou High-New Zone Songtian Enterprise Co., Ltd CT81 CD Max. 1000pF, Min.400VAC, 125 C, Y1 type, 2 pieces. (E145038) Max. 2200pF, Min.400VAC, 125 C, Y1 type, 2 pieces. (E208107) Max. 2200pF, Min.400VAC, 125 C, Y1 type, 2 Mark(s) of conformity Y capacitor Hsuan Tai Electronics CY Series (CY3, CY4) Co Ltd pieces. (E ) curus Max. 2200pF, Yinan Don's Electronic CT81 Min.400VAC, 125 C, Y1 type, 2 Component Co Ltd pieces. (E145038) Bright Led Electronics Corp BPC-817 (Series) Dti=0.4mm, int.dcr=5.2mm, Ext.dcr=8.0mm, 100 C; (E236324) 4 8 Optical Sharp Corp Electronic isolators Dti=0.4mm, int.dcr=5.2mm, Components And PC817 (U2) Ext.dcr=8.0mm, 100 C; (E64380) Devices Div curus Dti=0.4mm, int.dcr=5.2mm, Shenzhen Orient ORPC-817 Ext.dcr=8.0mm, 100 C; (E Components Co Ltd (Series) ) 7 9 Transformer Shenzhen Anpinyuan Technology Co Ltd SUN1139B 6 10 PCB Various Various 2 11 Output wire Various 2 12 Quick connector Label (not 2 13 show) NOTES: SPT-2 or 2464 or 1185 Class 130 (B) electrical insulation systems, designated APY-01 (E ) certified UL 796, V-0, 130 C, 1.6mm thickness. See 5.0 curus 300V, 20AWG min., 60 C curus Various Various Width:4.8mm, with insulator curus Various Various certified UL 969, 85 C. curus 1) Not all item numbers are indicated (called out) in the photos, as their location is obvious. 2) Various means any type, from any manufacturer that complies with the "Technical data and securement means" and meets the "Mark(s) of conformity" can be used. 3) Indicates specific marks to be verified, which assures the agreed level of surveillance for the component. "NR" - indicates Unlisted and only visual examination is necessary. "See 5.0" indicates Unlisted components or assemblies to be evaluated periodically refer to section 5.0 for details.

9 Page 9 of Critical Unlisted CEC Components Transformer Spec. Photo # Item no. Name Manufacturer/Trademark Type / model 7 9 Transformer Shenzhen Anpinyuan Technology Co Ltd SUN1139B Electrical Rating: / Insulation class Component Standard used: Bobbin Chang Chun T375J UL 1012 Eighth Edition Dated November 9, 2010 containing Revisions through and including May 14, 2014 CSA C22.2 No Dated September 2001, Reaffirmed 2011 MATERIALS LIST Component Manufacturer Type/model Dimensions/thickness/assembly information Core Various Various Ferrite Phenolic, V-0,150 C, min Thick.:1.0mm, (E59481) B Tipple Insulation Wire Furukawa Electric Co Ltd TEX-B for secondary winding 130 C, reinforced insulation, (E206440) 3m Company Electrical Markets Div (Emd) 1350F C, (E ) Insulation tape Jingjiang Yahua Pressure Sensitive Glue Co Ltd PZ, CT, WF 130 C; (E165111) Symbio Inc C, (E50292 ) Varnish Hitachi Chemical Co., Ltd WP-2952F- 2G 130 C, (E72979 ) Margin tape Jingjiang Yahua Pressure Sensitive Glue PZ 130 C, (E165111) WINDING(S) RESISTANCE Winding Wire Size DC resistance Designation (AWG or mm 2 Wire Type Turns Volts Amps ) (Ω) +/- 10%: N1 Coil 0.55X6 TEX-B 6 / / / N5 Coil 0.3X4mm 2UEW 18 / / / N4 Coil 0.5x2 2UEW 43 / / / N3 Coil 0.3X4mm 2UEW 8 / / / N2 Coil 0.55X6 TEX-B 6 / / / VERIFICATION PROCESS Frequency: Annual Test Site: CEC Number of samples to test: 3 Test Name Test Parameters Winding resistance See resistance per winding above(check turn number). Apply voltage Between Test Voltage Test Time Dielectric Strength Primary to core s Primary to secondary s Secondary to core s Illustration for transformer spec.

10 Page 10 of Critical Features Recognized Component - A component part, which has been previously evaluated by an accredited certification body with restrictions and must be evaluated as part of the basic product considering the restrictions as specified by the Conditions of Acceptability. Listed Component - A component part, which has been previously Listed or Certified by an accredited Certification Organization with no restrictions and is used in the intended application within its ratings. Unlisted Component - A part that has not been previously evaluated to the appropriate designated component standard. It may also be a Listed or Recognized component that is being used outside of its evaluated Listing or component recognition. Critical Features/Components - An essential part, material, subassembly, system, software, or accessory of a product that has a direct bearing on the product s conformance to applicable requirements of the product standard. Construction Details - For specific construction details, reference should be made to the photographs and descriptions. All dimensions are approximate unless specified as exact or within a tolerance. In addition to the specific construction details described in this Report, the following general requirements also apply. 1. Spacing - In primary circuits, minimum spacings are maintained 3.2 mm through air and 6.4 over surfaces of insulating material between current-carrying parts of opposite polarity and between current-carrying parts and dead-metal parts. The spacings between field wiring terminals of opposite polarity or between the field wiring terminal and other uninsulated metal parts, not of the same polarity, are minimum 6.4 mm through-air and over-surface. The spacings between a Class 2 circuit and non-class 2 circuits, and accessible metal, and grounded metal shall not be less than 6.4 mm. 2. Mechanical Assembly - Components such as switches, fuseholders, connectors, wiring terminals and display lamps are mounted and prevented from shifting or rotating by the use of lockwashers, starwashers, or other mounting format that prevents turning of the component. 3. Corrosion Protection - All ferrous metal parts are protected against corrosion by painting, plating or the equivalent. 4. Accessibility of Live Parts - All uninsulated live parts in primary circuitry are housed within a metal and nonmetallic enclosure constructed with no openings other than those specifically described in Sections 4 and Grounding - All exposed dead-metal parts and all dead-metal parts within the enclosure that are exposed are connected to the grounding lead of the power supply cord. 6. Polarized Connection - NA 7. Internal Wiring - NA(no internal wire) 8. Circuit diagram - Refer to Illustration No. 2 for circuit diagram requiring verification during Field Representative Inspection Audits. 9. Markings - The product is marked on a labeling system as described in item No.14 of Section 4.0 as follows: manufacturer's name, brand name, model number, date of manufacturer, electrical ratings.refer to 7.0 Illustrations No.1 for details Cautionary Markings - None. 11. Installation, Operating and Safety Instructions - Instructions for installation and use of this product are provided by the manufacturer. Refer to Illustration No(s).4, 4a, 4b, 4c, 4d for details. 12. PWB layout - Refer to Illustration No. 3 for requiring verification during Field Representative Inspection Audits.

11 7.0 Illustrations Illustration 1- Label Page 11 of 25 Remark: 1. The control number and wording CONFORMS TO UL STD.1012 CERTIFIED TO CSA STD. C22.2 No " shall be at least 1.5 mm high. 2. The ETL & cetl logo shall not be less than 8 mm in width and 8 mm in height, the US, C and control number shall not be less than 2 mm in height. The CM shall not be less than 1mm in height."intertek"shall not less than 3 mm in height. 3. Date code of manufacture (Series No. ) (not shown): "Month/YYYY " represent the month and after four numbers"yyyy " represent the year.

12 7.0 Illustrations Illustration 2 - Circuit diagram Page 12 of 25

13 7.0 Illustrations Illustration 3 - PWB layout Page 13 of 25

14 7.0 Illustrations Illustration 4- Manual Page 14 of 25

15 7.0 Illustrations Illustration 4a- Manual (continued) Page 15 of 25

16 7.0 Illustrations Illustration 4b- Manual (continued) Page 16 of 25

17 7.0 Illustrations Illustration 4c- Manual (continued) Page 17 of 25

18 7.0 Illustrations Illustration 4d- Manual (continued) Page 18 of 25

19 Page 19 of Test Summary Evaluation Period to Project No SHA Sample Rec. Date 5-Aug-2015 Condition Prototype Sample ID Test Location Test Procedure Building No. 86, 1198 Qinzhou Road (North), Shanghai , P. R. China Testing Lab Determination of the result includes consideration of measurement uncertainty from the test equipment and methods. The product was tested as indicated below with results in conformance to the relevant test criteria. The following tests were performed: Test Description Leakage Current Test Power Input Test Temperature (normal) Test Dielectric Strength Tests on insulating materials Strain Relief Test Push-back Relief Conduit Connections(Ploymeric Enclosures): Pullout Conduit Connections(Ploymeric Enclosures): Torque Conduit Connections(Ploymeric Enclosures): Bending Secrement of Components Capacitor Discharge(Energy and Shock Hazards) Bonding Continuity Overload of Switches and Controls Static load test Abormal test: Output short circuit test Abormal test: Relay and solenoid burnout Abormal test: Transformer overload test Abormal test: Component short- and open-circuit test Flanged Bobbin Transformer Abnormal Test Capacitor Test Abnormal Operation Resistance to Impact Mold-Stress Relief Distortion Stain-Relief Test after Mold-Stress Relief Distortion UL 1012 Eighth Edition Dated November 9, 2010 containing Revisions through and including May 14, 2014 CSA C22.2 No Dated September 2001, Reaffirmed 2011 UL 746C Sixth Edition Dated September 10, 2004 containing Revisions through and including October 16, Signatures A representative sample of the product covered by this report has been evaluated and found to comply with the applicable requirements of the standards indicated in Section 1.0. Completed by: Eric Shao Reviewed by: Will Wang Title: Engineer Title: Supervisor Signature: Signature:

20 Page 20 of Correlation Page For Multiple Listings The following products, which are identical to those identified in this report except for model number and Listee name, are authorized to bear the ETL label under provisions of the Intertek Multiple Listing Program. BASIC LISTEE Address Country Product 5F., No.8, Alley 11, Lane 327, Sec. 2, Chung San Road, Chung Ho, Taipei County Taiwan Switching Power Supply MULTIPLE LISTEE 1 Address Country Brand Name ASSOCIATED MANUFACTURER Address Country None MULTIPLE LISTEE 1 MODELS BASIC LISTEE MODELS MULTIPLE LISTEE 2 Address Country Brand Name ASSOCIATED MANUFACTURER Address Country None MULTIPLE LISTEE 2 MODELS BASIC LISTEE MODELS MULTIPLE LISTEE 3 Address Country Brand Name ASSOCIATED MANUFACTURER Address Country None MULTIPLE LISTEE 3 MODELS BASIC LISTEE MODELS

21 Page 21 of General Information The Applicant and Manufacturer have agreed to produce, test and label ETL Listed products in accordance with the requirements of this Report. The Manufacturer has also agreed to notify Intertek and to request authorization prior to using alternate parts, components or materials. COMPONENTS Components used shall be those itemized in this Intertek report covering the product, including any amendments and/or revisions. LISTING MARK The ETL Listing mark applied to the products shall either be separable in form, such as labels purchased from Intertek, or on a product nameplate or other media only as specifically authorized by Intertek. Use of the mark is subject to the control of Intertek. The mark must include the following four items: 1) applicable country identifiers "US" and/or "C" or "US", "C" and "EU" 2) the word "Listed" or "Classified" or "Recognized Component" (whichever is appropriate) 3) a control number issue by Intertek 4) a product descriptor that identifies the standards used for certification. Example: For US standards, the words, Conforms to shall appear with the standard number along with the word, Standard or Std. Example: Conforms to ANSI/UL Std. XX. For Canadian standards, the words Certified to CAN/CSA Standard CXX No. XX. shall be used, or abbreviated, Cert. to CAN/CSA Std. CXX No. XX. Can be used together when both standards are used. Note: A facsimile must be submitted to Intertek, Attn: Follow-up Services for approval prior to use. The facsimile need not have a control number. A control number will be issued after signed Certification Agreements have been received by the Follow-up Services office, approval of the facsimile of your proposed Listing Mark, satisfactory completion of the Listing Report, and scheduling of a factory assessment in your facility. MANUFACTURING AND PRODUCTION TESTS Manufacturing and Production Tests shall be performed as required in this Report. FOLLOW-UP SERVICE Periodic unannounced audits of the manufacturing facility (and any locations authorized to apply the mark) shall be scheduled by Intertek. An audit report shall be issued after each visit. Special attention will be given to the following: 1. Conformance of the manufactured product to the descriptions in this Report. 2. Conformance of the use of the ETL mark with the requirements of this Report and the Certification Agreement. 3. Manufacturing changes. 4. Performance of specified Manufacturing and Production Tests. In the event that the Intertek representative identifies non-conformance(s) to any provision of this Report, the Applicant shall take one or more of the following actions: 1. Correct the non-conformance. 2. Remove the ETL Mark from non-conforming product. 3. Contact the issuing product safety evaluation center for instructions.

22 Page 22 of Evaluation of Unlisted Components Because Unlisted Components are uncontrolled, and they do not fall under a third party follow up program, Intertek may require these components to be tested and/or evaluated at least once annually, more often for certain components, as part of the independent certification process. The Unlisted Components in Section 5.0 require testing and/or evaluation as indicated. Note to Intertek Follow Up Inspector: The Component Evaluation Center, CEC, will notify you in writing when these components must be selected and sent to the CEC for re-evaluation Ship the samples to: Intertek Testing Services Shanghai Limited ETL Component Evaluation Center Building No. 86, 1198 Qinzhou Road (North) Shanghai , China Attn: Ms. Dansy Xu Sample Disposition: Due to the destructive nature of the testing, all samples will be discarded at the conclusion of testing unless, the manufacturer specifically requests the return of the samples. The request for return must accompany the initial component shipment.

23 Page 23 of Manufacturing and Production Tests The manufacturer agrees to conduct the following Manufacturing and Production Tests as specified: Required Tests Dielectric Voltage Withstand Test Grounding Continuity Test 11.1 Dielectric Voltage Withstand Test Method One hundred percent of production of the products covered by this Report shall be subjected to a routine production line dielectric withstand test. The test shall be conducted on products, which are fully assembled. Prior to applying the test potential, all switches, contactors, relays, etc., should be closed so that all primary circuits are energized by the test potential. If all primary circuits cannot be tested at one time, then separate applications of the test potential shall be made. The test voltage specified below shall be applied between primary circuits and accessible dead-metal parts. The test voltage may be gradually increased to the specified value but must be maintained at the specified value for one second or one minute as required. Test Equipment The test equipment shall incorporate a transformer with an essentially sinusoidal output, a means to indicate the applied test potential, and an audible and/or visual indicator of dielectric breakdown. The test equipment shall incorporate a voltmeter in the output circuit to indicate directly the applied test potential if the rated output of the test equipment is less than 500VA. If the rated output of the test equipment is 500VA or more, the applied test potential may be indicated by either: 1 - a voltmeter in the primary circuit; 2 - a selector switch marked to indicate the test potential; or 3 - a marking in a readily visible location to indicate the test potential for test equipment having a single test potential output. In cases 2 and 3, the test equipment shall include a lamp or other visual means to indicate that the test potential is present at the test equipment output. All test equipment shall be maintained in current calibration. Products Requiring Dielectric Voltage Withstand Test: Product Test Voltage Test Time All products covered by this Report. 1000V 60 s or 1200V 1 s

24 Page 24 of Grounding Continuity Test Method Each unit that has a power supply cord having a grounding conductor shall be tested for continuity between the grounding blade of the attachment plug and the inaccessible dead metal parts of the appliance that are required to be grounded. This may require testing before final assembly of the enclosure. Any indicating device (an ohmmeter, a battery-and-buzzer combination, or the like) may be used to determine compliance with the grounding continuity. Products Requiring Dielectric Voltage Withstand Test: Product All products covered by this Report.

25 Page 25 of Revision Summary The following changes are in compliance with the declaration of Section 8.1: Date/ Project Handler/ Proj # Site ID Reviewer Section Item Description of Change None