General-Purpose AC Servo. MELSERVO-J4 Servo amplifier INSTRUCTION MANUAL TROUBLE SHOOTING

Size: px
Start display at page:

Download "General-Purpose AC Servo. MELSERVO-J4 Servo amplifier INSTRUCTION MANUAL TROUBLE SHOOTING"

Transcription

1 General-Purpose AC Servo MELSERVO-J4 Servo amplifier INSTRUCTION MANUAL TROUBLE SHOOTING

2 Safey Insrucions Please read he insrucions carefully before using he equipmen. To use he equipmen correcly, do no aemp o insall, operae, mainain, or inspec he equipmen unil you have read hrough his Insrucion Manual, Insallaion guide, and appended documens carefully. Do no use he equipmen unil you have a full knowledge of he equipmen, safey informaion and insrucions. In his Insrucion Manual, he safey insrucion levels are classified ino "WARNING" and "CAUTION". WARNING CAUTION Indicaes ha incorrec handling m cause hazardous condiions, resuling in deah or severe injury. Indicaes ha incorrec handling m cause hazardous condiions, resuling in medium or sligh injury o personnel or m cause physical damage. Noe ha he CAUTION level m lead o a serious consequence according o condiions. Please follow he insrucions of boh levels because hey are imporan o personnel safey. Wha mus no be done and wha mus be done are indicaed by he following diagrammaic symbols. Indicaes wha mus no be done. For example, "No Fire" is indicaed by. Indicaes wha mus be done. For example, grounding is indicaed by. In his Insrucion Manual, insrucions a a lower level han he above, insrucions for oher funcions, and so on are classified ino "POINT". Afer reading his Insrucion Manual, keep i accessible o he operaor. A - 1

3 1. To preven elecric shock, noe he following WARNING Before wiring or inspecion, urn off he power and wai for 15 minues or more unil he charge lamp urns off. Then, confirm ha he volage beween P+ and N- is safe wih a volage eser and ohers. Oherwise, an elecric shock m occur. In addiion, when confirming wheher he charge lamp is off or no, alws confirm i from he fron of he servo Do no operae swiches wih we hands. Oherwise, i m cause an elecric shock. 2. To preven fire, noe he following CAUTION When you use a MR-J4 muli-axis servo amplifier, connecing an encoder for differen axis o he CN2A, CN2B, or CN2C connecor m cause a fire. 3. To preven injury, noe he following CAUTION The servo amplifier hea sink, regeneraive resisor, servo moor, ec. m be ho while power is on or for some ime afer power-off. Take safey measures, e.g. provide covers, o preven accidenal conac of hands and pars (cables, ec.) wih hem. 4. Addiional insrucions The following insrucions should also be fully noed. Incorrec handling m cause a malfuncion, injury, elecric shock, ec. (1) Wiring CAUTION Wire he equipmen correcly and securely. Oherwise, he servo moor m operae unexpecedly. To avoid a malfuncion, connec he wires o he correc phase erminals (U, V, and W) of he servo amplifier and servo moor. Connec he servo amplifier power oupu (U, V, and W) o he servo moor power inpu (U, V, and W) direcly. Do no le a magneic conacor, ec. inervene. Oherwise, i m cause a malfuncion. Servo amplifier U V W U V W Servo moor M Servo amplifier U V W Servo moor U V M W A - 2

4 (2) Usage CAUTION Before reseing an alarm, make sure ha he run signal of he servo amplifier is off in order o preven a sudden resar. Oherwise, i m cause an acciden. Use he servo amplifier wih he specified servo moor. (3) Correcive acions CAUTION When i is assumed ha a hazardous condiion m occur due o a power failure or produc malfuncion, use a servo moor wih an elecromagneic brake or exernal brake o preven he condiion. Configure an elecromagneic brake circui so ha i is acivaed also by an exernal EMG sop swich. Conacs mus be opened when CALM (Common malfuncion) or MBR (Elecromagneic brake inerlock) urns off. Conacs mus be opened wih he EMG sop swich. Servo moor RA B 24 V DC Elecromagneic brake When any alarm has occurred, eliminae is cause, ensure safey, and deacivae he alarm before resaring operaion. Provide an adequae proecion o preven unexpeced resar afer an insananeous power failure. <<Abou he manual>> This Insrucion Manual covers he following models. MR-J4-_A MR-J4-_B MR-J4W_-_B The symbols in he arge column mean as follows. MR-J4-_A: MR-J4-_B: MR-J4W_-_B: A - 3

5 MEMO A - 4

6 CONTENTS 1. TROUBLESHOOTING 1-1 o Alarm and warning lis Remedies for alarms Remedies for warnings APPENDIX App.- 1 o App.- 1 App. 1 Deecion poins of [AL. 25], [AL. 92], and [AL. 9F]...App.- 1 1

7 MEMO 2

8 1. TROUBLESHOOTING 1.1 Alarm and warning lis When an error occurs during operaion, he corresponding alarm or warning is displed. If any alarm or warning has occurred, refer o secion 1.2 and ake he appropriae acion. When an alarm occurs, ALM (Malfuncion) will urn off. Alarm No. Name Deail displ Deail name 10 Undervolage 10.1 Volage drop in he conrol power 10.2 Volage drop in he main circui power 11 Swich seing error 11.1 Axis number seing error 11.2 Disabling conrol axis seing error 12 Memory error 1 (RAM) 12.1 RAM error RAM error RAM error RAM error RAM error 5 13 Clock error 13.1 Clock error Clock error 2 14 Conrol process error 14.1 Conrol process error Conrol process error Conrol process error Conrol process error Conrol process error Conrol process error Conrol process error Conrol process error Conrol process error 9 14.A Conrol process error Memory error 2 (EEP-ROM) 15.1 EEP-ROM error a power on 15.2 EEP-ROM error during operaion 16 Encoder iniial communicaion 16.1 Encoder iniial communicaion - Receive daa error 1 error Encoder iniial communicaion - Receive daa error Encoder iniial communicaion - Receive daa error Encoder iniial communicaion - Transmission daa error Encoder iniial communicaion - Transmission daa error Encoder iniial communicaion - Transmission daa error 3 16.A Encoder iniial communicaion - Process error 1 16.B Encoder iniial communicaion - Process error 2 16.C Encoder iniial communicaion - Process error 3 16.D Encoder iniial communicaion - Process error 4 16.E Encoder iniial communicaion - Process error 5 16.F Encoder iniial communicaion - Process error 6 17 Board error 17.1 Board error Board error Board error Board error Board error 5 19 Memory error 3 (Flash-ROM) 19.1 Flash-ROM error Flash-ROM error 2 1A Servo moor combinaion error 1A.1 Servo moor combinaion error 1A.2 Servo moor conrol mode combinaion error 1E Encoder iniial communicaion 1E.1 Encoder malfuncion error 2 1F Encoder iniial communicaion 1F.1 Incompaible encoder error 3 1-1

9 Alarm No. Name Deail displ Deail name 20 Encoder normal communicaion 20.1 Encoder normal communicaion - Receive daa error 1 error Encoder normal communicaion - Receive daa error Encoder normal communicaion - Receive daa error Encoder normal communicaion - Transmission daa error Encoder normal communicaion - Transmission daa error Encoder normal communicaion - Transmission daa error Encoder normal communicaion - Receive daa error 4 20.A Encoder normal communicaion - Receive daa error 5 21 Encoder normal communicaion 21.1 Encoder daa error 1 error Encoder daa updae error 21.3 Encoder daa waveform error 21.4 Encoder non-signal error 21.5 Encoder hardware error Encoder hardware error Encoder daa error 2 24 Main circui error 24.1 Ground faul deeced by hardware deecion circui 24.2 Ground faul deeced by sofware deecion funcion 25 Absolue posiion erased 25.1 Servo moor encoder - Absolue posiion erased 27 Iniial magneic pole deecion 27.1 Magneic pole deecion - Abnormal erminaion error 27.2 Magneic pole deecion - Time ou error 27.3 Magneic pole deecion - Limi swich error 27.4 Magneic pole deecion - Esimaed error 27.5 Magneic pole deecion - Posiion deviaion error 27.6 Magneic pole deecion - Speed deviaion error 27.7 Magneic pole deecion - Curren error 28 Linear encoder error Linear encoder - Environmen error 2A Linear encoder error 1 2A.1 Linear encoder error 1-1 2A.2 Linear encoder error 1-2 2A.3 Linear encoder error 1-3 2A.4 Linear encoder error 1-4 2A.5 Linear encoder error 1-5 2A.6 Linear encoder error 1-6 2A.7 Linear encoder error 1-7 2A.8 Linear encoder error 1-8 2B Encoder couner error 2B.1 Encoder couner error 1 2B.2 Encoder couner error 2 30 Regeneraive error 30.1 Regeneraion hea error 30.2 Regeneraion signal error 30.3 Regeneraion feedback signal error 31 Overspeed 31.1 Abnormal moor speed 32 Overcurren 32.1 Overcurren deeced a hardware deecion circui (during operaion) 32.2 Overcurren deeced a sofware deecion funcion (during operaion) 32.3 Overcurren deeced a hardware deecion circui (during a sop) 32.4 Overcurren deeced a sofware deecion funcion (during a sop) 33 Overvolage 33.1 Main circui volage error 34 SSCNET receive error SSCNET receive daa error 34.2 SSCNET connecor connecion error 34.3 SSCNET communicaion daa error 34.4 Hardware error signal deecion 35 Command frequency error 35.1 Command frequency error 36 SSCNET receive error Coninuous communicaion daa error 37 Parameer error 37.1 Parameer seing range error 37.2 Parameer combinaion error 3A Inrush curren suppression circui 3A.1 Inrush curren suppression circui error error 3E Operaion mode error 3E.1 Operaion mode error 1-2

10 Alarm No. Name Deail displ Deail name 42 Servo conrol error 42.1 Servo conrol error by posiion deviaion 42.2 Servo conrol error by speed deviaion 42.3 Servo conrol error by orque/hrus deviaion 45 Main circui device overhea 45.1 Main circui device overhea error 46 Servo moor overhea 46.1 Abnormal emperaure of servo moor Abnormal emperaure of servo moor Thermisor disconneced 46.5 Abnormal emperaure of servo moor Abnormal emperaure of servo moor 4 47 Cooling fan error 47.1 Cooling fan sop error 47.2 Cooling fan speed reducion error 50 Overload Thermal overload error 1 during operaion 50.2 Thermal overload error 2 during operaion 50.3 Thermal overload error 4 during operaion 50.4 Thermal overload error 1 during a sop 50.5 Thermal overload error 2 during a sop 50.6 Thermal overload error 4 during a sop 51 Overload Thermal overload error 3 during operaion 51.2 Thermal overload error 3 during a sop 52 Error excessive 52.1 Excess droop pulse Excess droop pulse Error excessive during 0 orque limi 52.5 Excess droop pulse 3 54 Oscillaion deecion 54.1 Oscillaion deecion error 56 Forced sop error 56.2 Over speed during forced sop 63 STO iming error 63.1 STO1 off 56.3 Esimaed disance over during forced sop 63.2 STO2 off 8A USB communicaion ime-ou error 8A.1 USB communicaion ime-ou error 8E USB communicaion error 8E.1 USB communicaion receive error 888/ Wachdog 8E.2 USB communicaion checksum error 8E.3 USB communicaion characer error 8E.4 USB communicaion command error 8E.5 USB communicaion daa number error 88._/ 8888._ Wachdog 1-3

11 Warning No. Name Deail displ Deail name 91 Servo amplifier overhea warning 91.1 Main circui device overhea warning 92 Baery cable disconnecion 92.1 Encoder baery cable disconnecion warning warning 92.3 Baery degradaion 95 STO warning 95.1 STO1 off deecion 95.2 STO2 off deecion 96 Home posiion seing warning 96.1 In-posiion warning a home posiioning 96.2 Command inpu warning a home posiioning 96.3 Servo off warning a home posiioning 99 Sroke limi warning 99.1 Forward roaion sroke end off 99.2 Reverse roaion sroke end off 9F Baery warning 9F.1 Low baery 9F.2 Baery degradaion warning E0 Excessive regeneraion warning E0.1 Excessive regeneraion warning E1 Overload warning 1 E1.1 Thermal overload warning 1 during operaion E1.2 Thermal overload warning 2 during operaion E1.3 Thermal overload warning 3 during operaion E1.4 Thermal overload warning 4 during operaion E1.5 Thermal overload error 1 during a sop E1.6 Thermal overload error 2 during a sop E1.7 Thermal overload error 3 during a sop E1.8 Thermal overload error 4 during a sop E2 Servo moor overhea warning E2.1 Servo moor emperaure warning E3 Absolue posiion couner warning E3.1 Muli-revoluion couner ravel disance excess warning E3.2 Encoder absolue posiioning couner warning E3.5 Absolue posiion couner warning E4 Parameer warning E4.1 Parameer seing range error warning E5 ABS ime-ou warning E5.1 Time-ou during ABS daa ransfer E5.2 ABSM off during ABS daa ransfer E5.3 SON off during ABS daa ransfer E6 Servo forced sop warning E6.1 Forced sop warning E7 Conroller forced sop warning E7.1 Conroller forced sop warning E8 Cooling fan speed reducion E8.1 Decreased cooling fan speed warning warning E9 Main circui off warning E9.1 Servo-on signal on during main circui off E9.2 Bus volage drop during low speed operaion E9.3 Ready-on signal on during main circui off EA ABS servo-on warning EA.1 ABS servo-on warning EB The oher axis error warning EB.1 The oher axis error warning EC Overload warning 2 EC.1 Overload warning 2 ED Oupu wa excess warning ED.1 Oupu wa excess warning F0 Tough drive warning F0.1 Insananeous power failure ough drive warning F0.3 Vibraion ough drive warning F2 Drive recorder - Miswriing warning F2.1 Drive recorder - Area wriing ime-ou warning F2.2 Drive recorder - Daa miswriing warning F3 Oscillaion deecion warning F3.1 Oscillaion deecion warning 1-4

12 1.2 Remedies for alarms CAUTION When any alarm has occurred, eliminae is cause, ensure safey, and deacivae he alarm before resaring operaion. Oherwise, i m cause injury. If [AL. 25 Absolue posiion erased] occurs, alws make home posiion seing again. Oherwise, i m cause an unexpeced operaion. As soon as an alarm occurs, make he Servo-off saus and inerrup he main circui power. POINT When any of he following alarms has occurred, do no cycle he power repeaedly o resar. Doing so will cause a malfuncion of he servo amplifier and he servo moor. Remove is cause and allow abou 30 minues for cooling before resuming he operaion. [AL. 30 Regeneraive error] [AL. 45 Main circui device overhea] [AL. 46 Servo moor overhea] [AL. 50 Overload 1] [AL. 51 Overload 2] Remove he cause of he alarm in accordance wih his secion. Use MR Configuraor2 o refer o a facor of alarm occurrence. 1-5

13 Alarm No.: 10 Alarm conen Name: Undervolage The volage of he conrol circui power supply has dropped. The volage of he main circui power supply has dropped Volage drop in he conrol power 10.2 Volage drop in he main circui power (1) The connecion of he conrol circui power supply connecor (CNP2) has a failure. Check he conrol circui power supply connecor. I has a failure. I has no failure. Connec i correcly. Check (2). (2) The volage of he conrol circui power supply is low. (3) An insananeous power failure has occurred for longer ime han he specified ime. The ime will be 60 ms when [Pr. PA20] is "_ 0 ". The ime will be he value se in [Pr. PF25] when [Pr. PA20] is "_ 1 ". (1) The main circui power supply connecor (CNP1) was disconneced. (2) The volage of he main circui power supply is low. (3) The alarm has occurred during acceleraion. (4) The servo amplifier is malfuncioning. Check if he volage of he conrol circui power supply is lower han 160 V AC. Check if he power has a problem. Check he main circui power supply connecor. Check if he volage of he main circui power supply is lower han 160 V AC. Check ha he bus volage during acceleraion is 200 V DC or more. Check he bus volage value. The volage is lower han 160 V AC. The volage is higher han 160 V AC. I has a problem. I is disconneced. Review he volage of he conrol circui power supply. Check (3). Review he power. Connec i correcly. I is conneced. Check (2). The volage is lower han 160 V AC. The volage is higher han 160 V AC. The volage is less han 200 V DC. The volage is 200 V DC or more. The volage of he main circui power supply is 160 V AC or more, and he bus volage is less han 200 V DC. Increase he volage of he main circui power supply. Check (3). Increase he acceleraion ime consan. Or increase he power supply capaciy. Check (4). 1-6

14 Alarm No.: 11 Alarm conen Name: Swich seing error The seing of he axis selecion roary swich or auxiliary axis number seing swich is incorrec. The seing of he disabling conrol axis swich is incorrec Axis number seing error 11.2 Disabling conrol axis seing error (1) The seing of he Axis No. is incorrec. (1) The seing of he disabling conrol axis swich is incorrec. Check he seings of he auxiliary axis number seing swich (SW2) and axis selecion roary swich (SW1). Check he seing of he disabling conrol axis swich. When boh of he auxiliary axis number seing swiches are on, check he axis selecion roary swich if "E" is seleced for MR-J4W2, ("E" or "F" is seleced for MR- J4W2). Boh of he auxiliary axis number seing swiches are off. Check if he seing is as follows. 1) Only A-axis is disabled. 2) Only B-axis is disabled. 3) A-axis and B-axis are disabled. 4) A-axis and C-axis are disabled. The seing is oher han above. Se he axis No. correcly. Se i correcly. Alarm No.: 12 Name: Memory error 1 (RAM) Alarm conen A par (RAM) in he servo amplifier is failure RAM error 1 (1) A par in he servo Disconnec he cables I is repeaable. amplifier is failure. excep he conrol circui power supply, I is no repeaable. Check (2). and hen check he repeaabiliy. (2) Somehing near he device caused i. Check he power supply for noise RAM error 2 Check i wih he check mehod for [AL. 12.1] RAM error RAM error RAM error 5 I has a failure. Take counermeasures agains is cause. 1-7

15 Alarm No.: 13 Alarm conen Name: Clock error A par in he servo amplifier is failure. A clock error ransmied from he conroller occurred Clock error 1 (1) A par in he servo amplifier is failure. Disconnec he cables excep he conrol circui power supply, and hen check he repeaabiliy. Check if he error occurs when you connec he amplifier o he conroller. Check if he servo amplifier of he nex axis is malfuncioning. I is repeaable. I is no repeaable. Check (2). (2) A clock error I occurs. Replace he ransmied from he conroller. conroller occurred. I does no occur. Check (3). (3) The servo amplifier of he nex axis is malfuncioning. (4) Somehing near he device caused i. Check he power supply for noise. Check if he connecor is shored Clock error 2 Check i wih he check mehod for [AL. 13.1]. I is malfuncioning. I is no malfuncioning. I has a failure. amplifier of he nex axis. Check (4). Take counermeasures agains is cause. 1-8

16 Alarm No.: 14 Alarm conen Name: Conrol process error The process did no complee wihin he specified ime Conrol process error 1 (1) The parameer seing is incorrec. (2) Somehing near he device caused i. Check if he I is incorrec. Se i correcly. parameer seing is incorrec. I is correc. Check (2). Check he power I has a failure. Take supply for noise. counermeasures Check if he agains is cause. connecor is shored. I has no failure. Check (3) Conrol process error Conrol process error Conrol process error Conrol process error Conrol process error Conrol process error Conrol process error Conrol process error 9 14.A Conrol process error 10 (3) The servo amplifier is malfuncioning. amplifier, and hen check he repeaabiliy. Replace he conroller, and hen check he repeaabiliy. Check if he parameer seing is incorrec. I is no repeaable. (1) A synchronous signal I is repeaable. error ransmied from he conroller occurred. I is no repeaable. Check (2). (2) The parameer seing is incorrec. (3) Somehing near he device caused i. (4) The servo amplifier is malfuncioning. Check i wih he check mehod for [AL. 14.1]. I is incorrec. Se i correcly. I is correc. Check (3). Check he power I has a failure. Take supply for noise. counermeasures Check if he agains is cause. connecor is shored. I has no failure. Check (4). I is no repeaable. amplifier, and hen check he repeaabiliy. 1-9

17 Alarm No.: 15 Alarm conen Name: Memory error 2 (EEP-ROM) A par (EEP-ROM) in he servo amplifier is failure EEP-ROM error a power on 15.2 EEP-ROM error during operaion (1) EEP-ROM is malfuncioning a power on. Disconnec he cables excep he conrol circui power supply, and hen check he repeaabiliy. I is repeaable. I is no repeaable. Check (2). (2) Somehing near he Check he power I has a failure. Take device caused i. supply for noise. counermeasures Check if he connecor agains is cause. is shored. I has no failure. Check (3). (3) The number of wrie imes exceeded 100,000. Check if parameers has been used very frequenly. I has a failure. Change he process o use parameers less frequenly afer replacemen. (1) EEP-ROM is malfuncioning during normal operaion. Check if he error occurs when you change parameers I occurs. I does no occur. Check (2). during normal operaion. (2) A wrie error occurred while uning resuls was processed. Check if he alarm occurs afer an hour from power on. I akes an hour or more. I akes less han an hour. Check (3). (3) Somehing near he I has a failure. device caused i. Check he power supply for noise. Check if he connecor is shored. Take counermeasures agains is cause. Alarm No.: 16 Name: Encoder iniial communicaion error 1 Alarm conen Communicaion error occurred beween encoder and servo 16.1 Encoder iniial (1) An encoder cable is Check if he encoder I has a failure. Replace or repair he communicaion malfuncioning. cable is disconneced cable. - Receive daa or shored. error 1 I has no failure. Check (2) Encoder iniial communicaion - Receive daa error 2 (2) The servo amplifier is malfuncioning. (3) An encoder is malfuncioning. (4) Somehing near he device caused i. amplifier, and hen check he repeaabiliy. moor or linear encoder, and hen check he repeaabiliy. Check he noise, ambien emperaure, vibraion, ec. Check i wih he check mehod for [AL. 16.1]. I is no repeaable. I is repeaable. Check (3). I is no repeaable. moor. I is repeaable. Check (4). I has a failure. Take counermeasures agains is cause. 1-10

18 Alarm No.: 16 Name: Encoder iniial communicaion error 1 Alarm conen Communicaion error occurred beween encoder and servo 16.3 Encoder iniial communicaion - Receive daa (1) An axis no used is no se as disabled-axis. Check he seing of he disabling conrol axis swich (SW2). error 3 (2) An encoder cable was disconneced. I is no se as disabled-axis. I is se as disabledaxis. I is no conneced. Se i as disabledaxis. Check (2). Check if he encoder cable is conneced correcly. I is conneced. Check (3). Connec i correcly. (3) The parameer seing of wo-wire ype/fourwire Check he parameer seing. The seing is incorrec. Se i correcly. ype is incorrec. Type A: [Pr. PC22] Type B: [Pr. PC04] The seing is correc. Check (4). (4) An encoder cable is malfuncioning. Check if he encoder cable is disconneced or shored. I has a failure. I has no failure. Replace or repair he cable. Check (5). (5) The volage of he conrol circui power supply has been unsable. (6) The servo amplifier is malfuncioning. (7) An encoder is malfuncioning. (8) Somehing near he device caused i. Check he volage of he conrol circui power supply. amplifier, and hen check he repeaabiliy. moor, and hen check he repeaabiliy. Check he noise, ambien emperaure, vibraion, ec Encoder iniial Check i wih he check mehod for [AL. 16.1]. communicaion - Transmission daa error Encoder iniial communicaion - Transmission daa error Encoder iniial communicaion - Transmission daa error 3 The conrol circui power supply has been an insananeous power failure. Review he power and relaed pars. I has no failure. Check (6). I is no repeaable. I is repeaable. Check (7). I is no repeaable. moor. I is repeaable. Check (8). I has a failure. Take counermeasures agains is cause. 1-11

19 Alarm No.: 16 Name: Encoder iniial communicaion error 1 Alarm conen Communicaion error occurred beween encoder and servo 16.A Encoder iniial (1) The servo amplifier is communicaion - malfuncioning. Process error 1 (2) An encoder is malfuncioning. (3) Somehing near he device caused i. amplifier, and hen check he repeaabiliy. I is no repeaable. I is repeaable. Check (2). I is no repeaable. moor, and hen check moor. he repeaabiliy. I is repeaable. Check (3). Check he noise, ambien emperaure, vibraion, ec. 16.B Encoder iniial Check i wih he check mehod for [AL. 16.A]. communicaion - Process error 2 16.C Encoder iniial communicaion - Process error 3 16.D Encoder iniial communicaion - Process error 4 16.E Encoder iniial communicaion - Process error 5 16.F Encoder iniial communicaion - Process error 6 I has a failure. Take counermeasures agains is cause. 1-12

20 Alarm No.: 17 Alarm conen Name: Board error A par in he servo amplifier is malfuncioning Board error 1 (1) A curren deecion circui is malfuncioning. Check if he alarm occurs during he servo-on saus. I occurs. I does no occur. Check (2). (2) Somehing near he Check he noise, I has a failure. Take device caused i. ambien emperaure, counermeasures ec. agains is cause Board error 2 Check i wih he check mehod for [AL. 17.1]" Board error 3 (1) The servo amplifier Disconnec he cables I is repeaable. recogniion signal was excep he conrol no read properly. circui power supply, I is no repeaable. Check (2). and hen check he repeaabiliy. (2) Somehing near he I has a failure. device caused i. Check he noise, ambien emperaure, ec. Take counermeasures agains is cause Board error 4 (1) The seing value of he roary swich (SW1) Disconnec he cables excep he conrol I is repeaable. was no read properly. circui power supply, and hen check he I is no repeaable. Check (2). repeaabiliy. (2) Somehing near he I has a failure. device caused i. Check he noise, ambien emperaure, ec. Take counermeasures agains is cause Board error 5 (1) The seing value of he DIP swiches (SW2) was no read properly. Disconnec he cables excep he conrol circui power supply, and hen check he repeaabiliy. I is repeaable. I is no repeaable. Check (2). (2) Somehing near he I has a failure. device caused i. Check he noise, ambien emperaure, ec. Take counermeasures agains is cause. 1-13

21 Alarm No.: 19 Alarm conen Name: Memory error 3 (Flash-ROM) A par (Flash-ROM) in he servo amplifier is failure Flash-ROM error Flash-ROM error 2 (1) The Flash-ROM is malfuncioning. (2) Somehing near he device caused i. Disconnec he cables excep he conrol circui power supply, and hen check he repeaabiliy. Check he noise, ambien emperaure, ec. Check i wih he check mehod for [AL. 19.1]. I is repeaable. I is no repeaable. Check (2). I has a failure. Take counermeasures agains is cause. Alarm No.: 1A Name: Servo moor combinaion error Alarm conen The combinaion of servo amplifier and servo moor is incorrec. 1A.1 Servo moor (1) The servo amplifier and Check he model The combinaion is combinaion he servo moor was incorrec. error conneced incorrecly. 1A.2 Servo moor conrol mode combinaion error (2) The seing of [Pr. PA01] is no corresponding o he conneced servo moor. (3) An encoder is malfuncioning. (1) The seing of [Pr. PA01] is no corresponding o he conneced servo moor. name of he servo moor and corresponding servo Check he [Pr. PA01] seing. Roary servo moor: " 0 _" Linear servo moor: " 4 _" Direc drive moor: " 6 _" moor, and hen check he repeaabiliy. Check he [Pr. PA01] seing. Roary servo moor: " 0 _" Linear servo moor: " 4 _" Direc drive moor: " 6 _" The combinaion is correc. The combinaion is incorrec. The combinaion is correc. I is no repeaable. The combinaion is incorrec. Use hem in he correc combinaion. Check (2). Se [Pr. PA01] correcly. Check (3). moor. Se [Pr. PA01] correcly. Alarm No.: 1E Name: Encoder iniial communicaion error 2 Alarm conen An encoder is malfuncioning. 1E.1 Encoder (1) An encoder is I is no repeaable. malfuncion malfuncioning. moor, and hen moor. check he I is repeaable. Check (2). repeaabiliy. (2) Somehing near he device caused i. Check he noise, ambien emperaure, vibraion, ec. I has a failure. Take counermeasures agains is cause. 1-14

22 Alarm No.: 1F Name: Encoder iniial communicaion error 3 Alarm conen The conneced encoder is no compaible wih he servo 1F.1 Incompaible encoder (1) A servo moor or linear encoder, which is no compaible wih he servo amplifier, was conneced. (2) The sofware version of he servo amplifier does no suppor he servo moor or linear encoder. (3) An encoder is malfuncioning. Check he model he servo moor/linear encoder. I is no compaible wih he servo I is compaible wih he servo Check if he sofware I is no suppored. version suppors he servo moor/linear encoder. moor or linear encoder, and hen check he repeaabiliy. Replace i wih a compaible one. Check (2). amplifier o one which sofware version suppors he servo moor/linear encoder. I is suppored. Check (3). I is no repeaable. moor or linear encoder. I is repeaable. 1-15

23 Alarm No.: 20 Name: Encoder normal communicaion error 1 Alarm conen Communicaion error occurred beween encoder and servo 20.1 Encoder normal communicaion (1) An encoder cable is malfuncioning. - Receive daa error 1 (2) The servo amplifier is malfuncioning Encoder normal communicaion - Receive daa error Encoder normal communicaion - Receive daa error Encoder normal communicaion - Transmission daa error Encoder normal communicaion - Transmission daa error Encoder normal communicaion - Transmission daa error Encoder normal communicaion - Receive daa error 4 20.A Encoder normal communicaion - Receive daa error 5 (3) An encoder is malfuncioning. (4) Somehing near he device caused i. Check if he encoder I has a failure. Repair or replace he cable is disconneced cable. or shored. I has no failure. Check (2). amplifier, and hen check he repeaabiliy. moor or linear encoder, and hen check he repeaabiliy. Check he noise, ambien emperaure, vibraion, ec. Check i wih he check mehod for [AL. 20.1]. I is no repeaable. I is repeaable. Check (3). I is no repeaable. moor or linear encoder. I is repeaable. Check (4). I has a failure. Take counermeasures agains is cause. 1-16

24 Alarm No.: 21 Name: Encoder normal communicaion error 2 Alarm conen The encoder deeced an error signal Encoder daa error Encoder daa updae error 21.3 Encoder daa waveform error 21.4 Encoder nonsignal error 21.5 Encoder hardware error Encoder hardware error Encoder daa error 2 (1) The encoder deeced a high speed/acceleraion rae due o an oscillaion or oher facors. (2) An encoder is malfuncioning. (3) Somehing near he device caused i. (1) An encoder is malfuncioning. (2) Somehing near he device caused i. Decrease he loop gain, and hen check he repeaabiliy. moor, and hen check he repeaabiliy. Check he noise, ambien emperaure, vibraion, ec. moor, and hen check he repeaabiliy. Check he noise, ambien emperaure, ec. Check i wih he check mehod for for [AL. 21.2]. I is no repeaable. Use he encoder wih low loop gain. I is repeaable. Check (2). I is no repeaable. moor. I is repeaable. Check (3). I has a failure. Take counermeasures agains is cause. I is no repeaable. moor. I is repeaable. Check (2). I has a failure. Take counermeasures agains is cause. (1) A signal of he linear Check if he linear I has a failure. Review he wiring. encoder has no been encoder cable is inpued. wired correcly. I has no failure. Check (2). (2) Somehing near he device caused i. Check he noise, ambien emperaure, ec. Check i wih he check mehod for [AL. 21.2]. Check i wih he check mehod for [AL. 21.1]. I has a failure. Take counermeasures agains is cause. 1-17

25 Alarm No.: 24 Alarm conen Name: Main circui error A ground faul occurred on he servo moor power lines. A ground faul occurred a he servo moor Ground faul deeced by (1) The servo amplifier is malfuncioning. hardware deecion circui 24.2 Ground faul deeced by sofware deecion funcion (2) A ground faul or shor occurred a he servo moor power cable. (3) A ground faul occurred a he servo moor. Disconnec he servo moor power cables (U, V, and W) and check if he alarm occurs. Check if only he servo moor power cable is shored. Disconnec he servo moor power cables on moor side, and check insulaion of he moor (beween U, V, W, and ). Shu off he power, and check if he main circui power supply cable and servo moor power cable are in conac. Check he noise, ambien emperaure, ec. I occurs. I does no occur. Check (2). I is shored. moor power cable. I is no shored. Check (3). I is shored. moor. I is no shored. Check (4). (4) The main circui power They are in conac. Correc he wiring. supply cable and servo moor power cable were shored. Check (5). (5) Somehing near he device caused i. Check i wih he check mehod for [AL. 24.1]. They are no in conac. I has a failure. Take counermeasures agains is cause. 1-18

26 Alarm No.: 25 Alarm conen Name: Absolue posiion erased Absolue posiion daa in error Power was swiched on for he firs ime in he absolue posiion deecion sysem Servo moor encoder - Absolue posiion erased (1) Power was swiched on for he firs ime in he absolue posiion deecion sysem. (2) The baery was removed (replaced) when he conrol circui power supply was off. Check if his is he firs ime in he absolue posiion deecion sysem. Check if he baery was removed (changed) when he conrol circui power supply was off. This is he firs ime. This is no he firs ime. I was removed. Check ha he baery is mouned, and make home posiion reurn. Check (2). Check ha he baery is mouned, and make home posiion reurn. I was no removed. Check (3). (3) The baery volage is low. The baery is Check he baery volage wih a eser. I is less han DC 3.0 V. Replace he baery. consumed. I is DC 3.0 V or more. Check (4). (4) The volage drop of he baery cable is large. Check if a recommended wire is I is no used. Use a recommended wire. used. I is used. Check (5). (5) A baery cable is malfuncioning. (6) There is a loose connecion of he encoder cable on he servo moor side. Check for he loose connecion wih a eser. I has a failure. Replace he baery cable. I has no failure. Check (6). Check for he loose I has a failure. Repair or replace he connecion wih a encoder cable. eser. Measure he volage on he servo moor side. I has no failure. Check (7). Check if he absolue posiion sorage uni posiion sorage uni is conneced correcly. correcly. I is conneced. Check (8). (7) The absolue posiion I is no conneced. Connec he absolue sorage uni was no conneced for using a direc drive moor. (8) The servo amplifier is malfuncioning. (9) An encoder is malfuncioning. amplifier, and hen check he repeaabiliy. moor, and hen check he repeaabiliy. I is no repeaable. I is repeaable. Check (9). I is no repeaable. moor. 1-19

27 Alarm No.: 27 Alarm conen Name: Iniial magneic pole deecion error The iniial magneic pole deecion was no compleed properly Magneic pole deecion - (1) A moving par collided agains he machine. Abnormal erminaion 27.2 Magneic pole deecion - Time ou error 27.3 Magneic pole deecion - Limi swich error 27.4 Magneic pole deecion - Esimaed error 27.5 Magneic pole deecion - Posiion deviaion error 27.6 Magneic pole deecion - Speed deviaion error 27.7 Magneic pole deecion - Curren error (2) The wiring of he servo moor power cable is incorrec. Check if i collided. I collided. Move he sar posiion of he magneic pole deecion. I did no collided. Check (2). Check if he wiring of I has a failure. Correc he wiring. he servo moor power cable is correc. I has no failure. Check (3). Check he seing of Se i correcly. [Pr. PL02] and [Pr. incorrec. PL03]. The seing is correc. Check (4). (3) The linear encoder The seing is resoluion seing differs from he seing value. (4) The direcion of Check polariies of The mouning mouning linear direcion is incorrec. encoder is incorrec. (5) The magneic pole deecion volage level is small. (1) Only one of he limi swiches of FLS/RLS is on. (2) The magneic pole deecion volage level is small. (1) Boh of he limi swiches of FLS/RLS are on during he magneic pole deecion. he linear encoder and he linear servo moor. Check if he ravel disance during he magneic pole deecion is oo shor (for a posiion deecion mehod). Check if he ravel disance during he magneic pole deecion is oo long or if a vibraion is occurring (for a minue posiion deecion mehod). Check he limi swiches. Check if he ravel disance during he magneic pole deecion is oo shor (for a posiion deecion mehod). Check he limi swiches. Check i wih he check mehod for [AL. 27.1]. The mouning direcion is correc. I is oo shor. The ravel disance is oo long or a vibraion is occurring. Moun i correcly. Check (5). Increase i wih he [Pr. PL09] seing. Review he [Pr. PL17] seing. I has a failure. Remove he cause. Move he sar posiion of he magneic pole deecion. I has no failure. Check (2). I is oo shor. Increase i wih he [Pr. PL09] seing. Boh of hem are off. Turn on he limi swiches. 1-20

28 Alarm No.: 28 Name: Linear encoder error 2 Alarm conen Working environmen of linear encoder is no normal Linear encoder - Environmen error (1) The ambien emperaure of he linear encoder is ou of specificaions. (2) The signal level of he linear encoder has dropped. Check he ambien emperaure of he linear encoder. Check he mouning condiion of he linear encoder. I is ou of specificaions. I is wihin specificaions. I has a failure. Lower he emperaure. Conac he linear encoder manufacurer. Check (2). Correc he mouning mehod of he linear encoder. Alarm No.: 2A Name: Linear encoder error 1 Alarm conen An error of he linear encoder was deeced. (The deails differ depending on he linear encoder manufacurer.) 2A.1 Linear encoder (1) Mouning condiion of Adjus he posiions of I is no repeaable. Use he equipmen a error 1-1 he linear encoder and he scale and head, he adjused posiion. head is failure. and hen check he I is repeaable. Check (2). repeaabiliy. (2) Somehing near he I has a failure. device caused i. 2A.2 Linear encoder error 1-2 2A.3 Linear encoder error 1-3 2A.4 Linear encoder error 1-4 2A.5 Linear encoder error 1-5 2A.6 Linear encoder error 1-6 2A.7 Linear encoder error 1-7 2A.8 Linear encoder error 1-8 (3) An alarm of he linear encoder was deeced. Check he noise, ambien emperaure, vibraion, ec. Check he conen of he alarm deail lis of he Linear Encoder Insrucion Manual. Check i wih he check mehod for [AL. 2A.1]. Take counermeasures agains is cause. I has no failure. Check (3). Remove is cause described in he insrucion manual. Conac each encoder manufacurer for how o deal wih i. 1-21

29 Alarm No.: 2B Alarm conen Name: Encoder couner error Daa which encoder creaed is failure. 2B.1 Encoder couner error 1 2B.2 Encoder couner error 2 (1) An encoder cable is malfuncioning. (2) Somehing near he device caused i. (3) An encoder is malfuncioning. Check if he encoder cable is disconneced I has a failure. Repair or replace he cable. or shored. I has no failure. Check (2). Check he noise, I has a failure. Take ambien emperaure, counermeasures vibraion, ec. agains is cause. I has no failure. Check (3). Replace he direc drive moor, and hen check he repeaabiliy. Check i wih he check mehod for [AL. 2B.1]. I is no repeaable. Replace he direc drive moor. Alarm No.: 30 Name: Regeneraive error Alarm conen Permissible regeneraive power of he buil-in regeneraive resisor or regeneraive opion is exceeded. A regeneraive ransisor in he servo amplifier is malfuncioning Regeneraion hea error (1) The seing of he regeneraive resisor (regeneraive opion) is Check he regeneraive resisor (regeneraive opion) The seing value is incorrec. I is se correcly. Se i correcly. Check (2). incorrec. and [Pr. PA02] seing. (2) The regeneraive Check if he I is no conneced Connec i correcly Regeneraion signal error resisor (regeneraive opion) is no conneced. (3) Power supply volage high. (4) The regeneraive load raio has been over 100%. (1) A deecion circui of he servo amplifier is malfuncioning Regeneraion (1) A deecion circui of feedback signal he servo amplifier is error malfuncioning. (2) Somehing near he device caused i. regeneraive resisor (regeneraive opion) is conneced correcly. Check he inpu power supply volage. Check he regeneraive load raio when alarm occurs. Check if he regeneraive resisor (regeneraive opion) is overheaing. Remove he regeneraive opion or buil-in regeneraive resisor and hen check if he alarm occur a power on. Check he noise, ground faul, ambien emperaure, ec. correcly. I is conneced correcly. I is 240 V AC or more. I is less han 240 V AC. I is 100% or more. I is overheaing abnormally. The alarm occurs. The alarm does no occur. I has a failure. Check (3). Reduce he power supply volage. Check (4). Reduce he frequency of posiioning. Reduce he load. Use a regeneraive opion if no being using. Review he regeneraive opion capaciy. Check (2). Take counermeasures agains is cause. 1-22

30 Alarm No.: 31 Alarm conen Name: Overspeed The servo moor seed has exceeded he permissible insananeous speed. The linear servo moor seed has exceeded he permissible insananeous speed Abnormal (1) The command pulse moor speed frequency is high. (2) The command from he conroller is excessive. (3) A larger speed command han he overspeed alarm level was inpued. (4) The servo moor was a he maximum orque (maximum hrus) a he ime of acceleraion. (5) The servo sysem is unsable and oscillaing. (6) The velociy waveform has oversho. (7) The connecion desinaion of he encoder cable is incorrec. (8) The encoder or liner encoder is malfuncioning. Check he command pulse frequency. Check if he command from he conroller is over he permissible speed. Check ha he acual moor speed is higher han he seing value of [Pr. PC08 Overspeed alarm deecion level]. Check if he orque (hrus) a he ime of acceleraion is he maximum orque (maximum hrus). Check if he servo moor is oscillaing. The command pulse frequency is high. The command pulse frequency is low. I is over he permissible speed. I is less han he permissible speed. The moor speed is higher han he overspeed alarm deecion level. The moor speed is lower han he overspeed alarm level. I is he maximum orque (maximum hrus). I is less han he maximum orque (maximum hrus). I is oscillaing. Check operaion paern. Check (3). Check operaion paern. Check (3). Review he [Pr. PC08] seing. Check (4). Increase he acceleraion/decelera ion ime consan. Or reduce he load. Check (5). Adjus he servo gain. Or reduce he load. I is no oscillaing. Check (6). Check if i is I is overshooing. Increase he overshooing because acceleraion/decelera he acceleraion ime ion ime consan. consan is oo shor. I is no overshooing. Check (7). Check he connecion I is no correc. Wire i correcly. desinaions of CN2A, CN2B, and CN2C. Check if he alarm is occurring during less han permissible insananeous speed. I is correc. Check (8). I is occurring during less han permissible insananeous speed. moor or linear encoder. 1-23

31 Alarm No.: 32 Alarm conen Name: Overcurren Curren ha flew is higher han he permissible curren of he servo 32.1 Overcurren deeced a (1) The servo amplifier is malfuncioning. hardware deecion circui (during operaion) (2) A ground faul or shor occurred a he servo moor power cable. (3) The servo moor is malfuncioning. (4) The dynamic brake is malfuncioning. Disconnec he servo moor power cables (U, V, and W) and check if he alarm occurs. Check if only he servo moor power cable is shored. Disconnec he servo moor power cables on moor side, and check insulaion of he moor (beween U, V, W, and ). Check if he error occurs when you urn on he servo-on command. Check he connecion desinaions of CN2A, CN2B, and CN2C. I occurs. I does no occur. Check (2). I is shored. moor power cable. I is no shored. Check (3). A ground faul is occurring. A ground faul is no occurring. moor. Check (4). I occurs. I does no occur. Check (5). (5) The connecion desinaion of he encoder cable is incorrec. I is no correc. I is correc. Wire i correcly. Check (6). (6) Somehing near he device caused i. Check he noise, ambien emperaure, ec. I has a failure. Take counermeasures agains is cause. 1-24

32 Alarm No.: 32 Alarm conen Name: Overcurren Curren ha flew is higher han he permissible curren of he servo 32.2 Overcurren deeced a (1) The servo gain is high. Check if an oscillaion is occurring. sofware deecion funcion (during operaion) 32.3 Overcurren deeced a hardware deecion circui (during a sop) 32.4 Overcurren deeced a sofware deecion funcion (during a sop) (2) The servo amplifier is malfuncioning. (3) A ground faul or shor occurred a he servo moor power cable. (4) The servo moor is malfuncioning. Disconnec he servo moor power cables (U, V, and W) and check if he alarm occurs. Check if only he servo moor power cable is shored. Disconnec he servo moor power cables on moor side, and check insulaion of he moor (beween U, V, W, and ). Check he connecion desinaions of CN2A, CN2B, and CN2C. An oscillaion is occurring. An oscillaion is no occurring. Reduce he speed loop gain ([Pr. PB09]). Check (2). I occurs. I does no occur. Check (3). I is shored. moor power cable. I is no shored. Check (4). A ground faul is occurring. A ground faul is no occurring. moor. Check (5). (5) The connecion desinaion of he encoder cable is incorrec. I is no correc. I is correc. Connec i correcly. Check (6). (6) Somehing near he device caused i. Check he noise, ambien emperaure, ec. Check i wih he check mehod for [AL. 32.1]. Check i wih he check mehod for [AL. 32.2]. I has a failure. Take counermeasures agains is cause. 1-25

33 Alarm No.: 33 Alarm conen Name: Overvolage The value of he bus volage exceeded 400 V DC Main circui volage error (1) The seing of he regeneraive resisor (regeneraive opion) is incorrec. Check he regeneraive resisor (regeneraive opion) and [Pr. PA02] seing. The seing value is incorrec. I is se correcly. Se i correcly. Check (2). (2) The regeneraive Check if he I is no conneced Connec i correcly. resisor (regeneraive opion) is no conneced. (3) Wire breakage of builin regeneraive resisor or regeneraive opion (4) The regeneraion capaciy is insufficien. (5) Power supply volage high. (6) Somehing near he device caused i. regeneraive resisor (regeneraive opion) is conneced correcly. Measure he resisance of he builin regeneraive resisor or regeneraive opion. Se a larger deceleraion ime consan, and hen check he repeaabiliy. Check he inpu volage. Check he noise, ambien emperaure, ec. correcly. I is conneced correcly. The resisance is abnormal. The resisance is normal. I is no repeaable. Check (3). When using a buil-in regeneraive resisor, replace he servo When using a regeneraive opion, replace he regeneraive opion. Check (4). When using a buil-in regeneraive resisor, use a regeneraive opion. When using a regeneraive opion, use a larger capaciy one. I is repeaable. Check (5). I is over 264 V AC. Reduce he inpu volage. I is 264 V AC or less. Check (6). I has a failure. Take counermeasures agains is cause. 1-26

34 Alarm No.: 34 Name: SSCNET receive error 1 Alarm conen An error occurred in SSCNET III/H communicaion. (coninuous communicaion error wih 3.5 ms inerval) 34.1 SSCNET receive daa error 34.2 SSCNET connecor connecion error 34.3 SSCNET communicaion daa error 34.4 Hardware error signal deecion (1) The SSCNET III cable is disconneced. (2) The surface a he end of SSCNET III cable go diry. (3) The SSCNET III cable is broken or severed. Check he SSCNET III cable connecion. Wipe off he dir from he cable ip, and hen check he repeaabiliy. Check if he SSCNET III cable is malfuncioning. I is disconneced. Turn off he conrol circui power supply of he servo amplifier, and hen connec he SSCNET III cable. I is conneced. Check (2). I is no repeaable. Take measure o keep he cable ip clean. I is repeaable. Check (3). I has a failure. Replace he SSCNET III cable. I has no failure. Check (4). (4) A vinyl ape is sacked o he SSCNET III cable. Or a wire Check if a vinyl ape is used. Check if he cable is conacing I is used. They are in conac. Take counermeasures agains is cause. insulaor conaining wih oher cables. I is no used. They Check (5). migraing plasicizer is are no in conac. adhered o he cable. (5) The servo amplifier is malfuncioning. amplifier, and hen check he repeaabiliy. Replace he previous and nex servo amplifier of he alarm occurred axis, and hen check he repeaabiliy. Replace he conroller, and hen check he repeaabiliy. Check he noise, ambien emperaure, ec. I is no repeaable. I is repeaable. Check (6). (6) The previous or nex axis servo amplifier of he alarm occurred is malfuncioning. I is no repeaable. I is repeaable. Check (7). (7) The conroller is malfuncioning. (8) Somehing near he device caused i. Check i wih he check mehod for [AL. 34.1]. I is no repeaable. Replace he conroller. I is repeaable. Check (8). I has a failure. Take counermeasures agains is cause. 1-27

35 Alarm No.: 35 Alarm conen Name: Command frequency error Inpu pulse frequency of command pulse is oo high Command frequency error (1) The command pulse frequency is high. (2) The command from he conroller is excessive. (3) The conroller is malfuncioning. (4) Somehing near he device caused i. Check he command pulse frequency. Check if he command from he conroller is over he permissible speed. Replace he conroller, and hen check he repeaabiliy. Check he noise, ambien emperaure, ec. The command pulse frequency is high. The command pulse frequency is low. I is over he permissible speed. I is less han he permissible speed. I is no repeaable. Check operaion paern. Check (4). Check operaion paern. Check (3). Replace he conroller. I is repeaable. Check (4). I has a failure. Take counermeasures agains is cause. 1-28

36 Alarm No.: 36 Name: SSCNET receive error 2 Alarm conen An error occurred in SSCNET III/H communicaion. (inermien communicaion error wih abou 70 ms inerval) 36.1 Coninuous communicaion daa error (1) The SSCNET III cable is disconneced. (2) The surface a he end of SSCNET III cable go diry. Check he SSCNET III cable connecion. Wipe off he dir from he cable ip, and hen check he repeaabiliy. I is disconneced. Turn off he conrol circui power supply of he servo amplifier, and hen connec he SSCNET III cable. I is conneced. Check (2). I is no repeaable. Take measure o keep he cable ip clean. I is repeaable. Check (3). (3) The SSCNET III cable is broken or severed. Check if he SSCNET III cable is malfuncioning. I has a failure. I has no failure. Replace he SSCNET III cable. Check (4). (4) A vinyl ape is sacked Check if a vinyl ape I is used. They are in conac. Take counermeasures agains is cause. o he SSCNET III cable. Or a wire insulaor conaining migraing plasicizer is adhered o he cable. (5) The servo amplifier is malfuncioning. is used. Check if he cable is conacing wih oher cables. amplifier, and hen check he repeaabiliy. Replace he previous and nex servo amplifier of he alarm occurred axis, and hen check he repeaabiliy. Replace he conroller, and hen check he repeaabiliy. Check he noise, ambien emperaure, ec. I is no used. They are no in conac. Check (5). I is no repeaable. I is repeaable. Check (6). (6) The previous or nex I is no repeaable. axis servo amplifier of he alarm occurred is malfuncioning. I is repeaable. Check (7). (7) The conroller is malfuncioning. (8) Somehing near he device caused i. I is no repeaable. Replace he conroller. I is repeaable. Check (8). I has a failure. Take counermeasures agains is cause. 1-29

< Apparecchiatura di controllo di fiamma > RIVELAZIONE FIAMMA MONO - BI ELETTRODO. SAITEK srl

< Apparecchiatura di controllo di fiamma > RIVELAZIONE FIAMMA MONO - BI ELETTRODO. SAITEK srl Serie CF4q < Apparecchiaura di conrollo di fiamma > RIVELAZIONE FIAMMA MONO - BI ELETTRODO SAITEK srl www.saiek.i info@saiek.i Casalgrande (RE) ITALY Tel. +39 0522 848211 Fax +39 0522 849070 BURNER FLAME

More information

UF GENERAL DESCRIPTION 2. SHORT-FORM DATA 3. ORDER NUMBERS 4. MARKINGS BUFFER UNIT 1/11

UF GENERAL DESCRIPTION 2. SHORT-FORM DATA 3. ORDER NUMBERS 4. MARKINGS BUFFER UNIT 1/11 BUFFER UNIT Buffering wih elecrolyic capaciors insead of lead baeries Buffering of 24V loads Minimum hold-up ime 0.2s a 20A Longer hold-up ime a lower loads Clear saus indicaion by saus LED and signaling

More information

Wireless keypad RKB1. Data sheet. Device identification number:

Wireless keypad RKB1. Data sheet. Device identification number: Wireless keypad RKB1 Daa shee Device idenificaion number: 2 1. General Informaion The RKB1 wireless keypad wih LED indicaion (hereinafer referred o as he keypad) is designed for conrolling Rim radio channel

More information

CHIMNEY CENTRIFUGAL FAN KAMIN OPERATION MANUAL

CHIMNEY CENTRIFUGAL FAN KAMIN OPERATION MANUAL CHIMNEY CENTRIFUGAL FAN KAMIN OPERATION MANUAL CONTENT Inroducion 3 General 3 Safey rules 3 Sorage and ransporaion rules 3 Manufacurer's warrany 3 Fan design 4 Delivery se 4 Modificaions and opions 4 Technical

More information

SWIMMING POOL HEAT PUMP UNITS. Installation & Instruction Manual DURA+ - series

SWIMMING POOL HEAT PUMP UNITS. Installation & Instruction Manual DURA+ - series SWIMMIG POO HEAT PUMP UITS Insallaion & Insrucion Manual DURA+ - series Rev. 4.00 21.02.2014 Conens SWIMMIG POO HEAT PUMP UITS... 1! Conens... 2! 1. Preface... 3! 2. Specificaions... 4! 2.1 Technical daa

More information

Automatic Burner Controls IFS 110 IM

Automatic Burner Controls IFS 110 IM Auomaic Burner Conrols IFS 110 IM T 12..1.1. ediion 5.05 Block diagram for inerruped sysen Auomaic Burner Conrols IFS 110 IM Flame conrol by means of flame rod or UV-deecor Flame simulaion check before

More information

INSTALLATION AND OPERATING MANUAL

INSTALLATION AND OPERATING MANUAL INSTALLATION AND OPERATING MANUAL Réf.: REV A NPM32GB GAS DETECTION We are delighed ha you have chosen an INDUSTRIAL SCIENTIFIC insrumen and would like o hank you for your choice. We have aken all he necessary

More information

Exercises in causal loop diagrams (CLD s)

Exercises in causal loop diagrams (CLD s) Exercises in causal loop diagrams (CLD s) 1 Room hea A room is heaed by an elecrical heaer. Explain how he in he room is changed by he elecrical heaer using a causal loop diagram. Reference mode: Draw

More information

Built-in oven INSTRUCTION MANUAL C17MR02.0B

Built-in oven INSTRUCTION MANUAL C17MR02.0B Buil-in oven [en] INSTRUCTION MANUAL C17MR02.0B NO I ] ne [ en Table of conens TCURTSN I Inended use............................. 4 Imporan safey informaion............... 4 General informaion...........................

More information

FC121-ZA / FC122-ZA / FC123-ZA / FC124-ZA

FC121-ZA / FC122-ZA / FC123-ZA / FC124-ZA Fire Conrol Panel FC121-ZA / FC122-ZA / FC123-ZA / FC124-ZA Technical Manual Building Technologies A6V10393190_f_en_-- 2015-09-09 Conrol Producs and Sysems Legal noice Technical specificaions and availabiliy

More information

Compact oven with microwave. CM636GB.1 siemens-home.com/welcome. Register your product online

Compact oven with microwave. CM636GB.1 siemens-home.com/welcome. Register your product online Compac oven wih microwave CM636GB.1 siemens-home.com/welcome en Regiser your produc online no i c u r seni n l en Table of conens 8 Inended use............................. 4 ( Imporan safey informaion...............

More information

Process firing system PF 19

Process firing system PF 19 Process firing sysem PF 9 T 2.6.2. ediion 8.95 Process Firing ysem PF, PFF, PFR, PFP 9" rack large choice of differen subracks giving various applicaions in accordance wih he cusomer's specificaion High

More information

Configuration Software G3800 X015. User Manual Preliminary Data December 2002

Configuration Software G3800 X015. User Manual Preliminary Data December 2002 Du line Fieldbus Insallaionbus Configuraion Sofware G3800 X015 User Manual Preliminary Daa December 2002 Table of Conens 1. Inroducion 4 1.1. Sar-up 4 1.1.1. Hardware requiremens 4 1.1.2. Insallaion 4

More information

EBA 20 EBA 20 C Repair instructions

EBA 20 EBA 20 C Repair instructions EBA 20 EBA 20 C Repair insrucions 03.08 Andreas Heich GmbH & Co. KG AR2002EN Andreas Heich GmbH & Co. KG Föhrensraße 12, D-78532 Tulingen / Germany Phone (07461) 705-0 Fax (07461) 705-125 info@heichlab.com,

More information

SmartCella/SmartCella 3PH. Electronic controllers for cold rooms. User manual NO POWER & SIGNAL CABLES TOGETHER READ CAREFULLY IN THE TEXT!

SmartCella/SmartCella 3PH. Electronic controllers for cold rooms. User manual NO POWER & SIGNAL CABLES TOGETHER READ CAREFULLY IN THE TEXT! SmarCella/SmarCella 3PH Elecronic conrollers for cold rooms User manual NO POWER & SIGNAL CABLES TOGETHER READ CAREFULLY IN THE TEXT! H i g h E f f i c i e n c y S o l u i o n s WARNING DISPOSAL CAREL

More information

The effect of the fire detectors on gas turbine reliability

The effect of the fire detectors on gas turbine reliability ECE 802, secion 605 The effec of he fire deecors on gas urbine reliabiliy By: Mohammed Ben-Idris upervisor: Professor Mira December, 12, 2009 Ben-Idris 1 Absrac. Reliable fire, smoke, and gas leakage deecors

More information

User Manual. If you have any issues or questions, please contact us via

User Manual. If you have any issues or questions, please contact us via User Manual Thanks for choosing ImporAppliances for your kich appliance purchase. We hope you are joying he convice, qualiy and affordabiliy of your new appliance. If you have any issues or quesions, please

More information

Dishwasher SHEM78WH5N. en-us Operating instructions fr-ca Notice d'utilisation

Dishwasher SHEM78WH5N. en-us Operating instructions fr-ca Notice d'utilisation Dishwasher SHEM78WH5N en-us Operaing insrucions fr-ca Noice d'uilisaion 2 en-us gn i a r epo s no i c u r s n i en-us Table of conens ( Safey Definiions...........5 ( IMPORTANT SAFETY INSTRUCTIONS............6

More information

ir33+ Electronic controller User manual

ir33+ Electronic controller User manual ir33+ Elecronic conroller User manual H i g h E f f i c i e n c y S o l u i o n s IMPORTANT HACCP WARNING CAREL bases he developmen of is producs on decades of experience in HVAC, on he coninuous invesmens

More information

User manual. EVD evolution twin. Driver for 2 electronic expansion valves. Integrated Control Solutions & Energy Savings READ CAREFULLY IN THE TEXT!

User manual. EVD evolution twin. Driver for 2 electronic expansion valves. Integrated Control Solutions & Energy Savings READ CAREFULLY IN THE TEXT! EVD evoluion win Driver for 2 elecronic expansion valves User manual NO POWER & SIGNAL CABLES TOGETHER READ CAREFULLY IN THE TEXT! Inegraed Conrol Soluions & Energy Savings WARNINGS DISPOSAL CAREL INDUSTRIES

More information

L8151A Triple Aquastat Relay

L8151A Triple Aquastat Relay L85A riple Aquastat Relay he L85A is a remote bulb controller for use with hydronic heating systems that include domestic hot water service. Provides high limit, low limit, and circulator control for maintaining

More information

Single Package Heat Pump. important:

Single Package Heat Pump. important: 13 SEER Single Package Hea Pump Single Package Hea Pump important: Read his owner informaion o become familiar wih he capabiliies and use of your appliance. Keep his wih lieraure on oher appliances where

More information

User manual. EVD evolution. electronic expansion valve driver. Integrated Control Solutions & Energy Savings READ CAREFULLY IN THE TEXT!

User manual. EVD evolution. electronic expansion valve driver. Integrated Control Solutions & Energy Savings READ CAREFULLY IN THE TEXT! EVD evoluion elecronic expansion valve driver User manual NO POWER & SIGNAL CABLES TOGETHER READ CAREFULLY IN THE TEXT! Inegraed Conrol Soluions & Energy Savings WARNINGS DISPOSAL CAREL bases he developmen

More information

L7224A,C; L7248A,C,L Oil Electronic Aquastat Controllers

L7224A,C; L7248A,C,L Oil Electronic Aquastat Controllers L74A,C; L748A,C,L Oil Electronic Aquastat Controllers APPLICAION he L74A,C and L748A,C,L Oil Electronic Aquastat Controllers provide electronic temperature sensing in a UL limit-rated control with a single

More information

ir33+ platform ir33+, ir33+wide, ir33+ small wide easy wide y easy small wide Electronic controller User manual

ir33+ platform ir33+, ir33+wide, ir33+ small wide easy wide y easy small wide Electronic controller User manual ir33+ plaform ir33+, ir33+wide, ir33+ small wide easy wide y easy small wide Elecronic conroller User manual I n e g r a e d C o n r o l S o l u i o n s & E n e r g y S a v i n g s IMPORTANT DISPOSAL

More information

UltraCella. Electronic control for Cold Rooms. User manual NO POWER & SIGNAL CABLES TOGETHER READ CAREFULLY IN THE TEXT!

UltraCella. Electronic control for Cold Rooms. User manual NO POWER & SIGNAL CABLES TOGETHER READ CAREFULLY IN THE TEXT! UlraCella Elecronic conrol for Cold Rooms User manual NO POWER & SIGNAL CABLES TOGETHER READ CAREFULLY IN THE TEXT! H i g h E f f i c i e n c y S o l u i o n s WARNING DISPOSAL CAREL developed is producs

More information

R8182D,E,F,H,J Combination Protectorelay Primary Control and Aquastat Controller

R8182D,E,F,H,J Combination Protectorelay Primary Control and Aquastat Controller R88D,E,F,H,J Combination Protectorelay Primary Control and Aquastat Controller APPLICAION he R88 combines a Protectorelay primary control and immersion type Aquastat controller in one unit for use in oil-fired,

More information

Technical Data. Specifications are typical and given at 23 C & 50% relative humidity unless stated.

Technical Data. Specifications are typical and given at 23 C & 50% relative humidity unless stated. 34865 A4 44pp: plus final singles 10/01/2011 16:32 Page 13 IONISATION S M OK E D ETECTOR Par Number 55000-500IMC Type: Flaming combusion Very good Very good Ionisaion Smoke Deecor, XPERT syle, 55000-500IMC

More information

L7224A,C; L7248A,C,L Oil and Electric Boiler Electronic Aquastat Controllers

L7224A,C; L7248A,C,L Oil and Electric Boiler Electronic Aquastat Controllers L74A,C; L748A,C,L Oil and Electric Boiler Electronic Aquastat Controllers APPLICAION he L74A,C and L748A,C,L 0 Compliant Electronic Aquastat Controllers provide electronic temperature sensing in a UL limit-rated

More information

EVD evolution. electronic expansion valve driver. User manual. Integrated Control Solutions & Energy Savings

EVD evolution. electronic expansion valve driver. User manual. Integrated Control Solutions & Energy Savings EVD evoluion elecronic expansion valve driver User manual Inegraed Conrol Soluions & Energy Savings WARNINS DISPOSAL CAREL bases he developmen of is producs on decades of experience in HVAC, on he coninuous

More information

Two-Stage Compression Centrifugal Chiller

Two-Stage Compression Centrifugal Chiller Two-Sage Compression Cenrifugal Chiller hp://www.ers.ebara.com/en/ Model ype series in his caalogue is our model code. Head Office & Sales Deparmen 3--16 Ohmorikia, Tokyo 143-0016, JPN Phone: +81-3-6384-8145

More information

Why Mendel Succeeded. Why Mendel Succeeded. Mendel chose his subject carefully. Mendel chose his subject carefully. Mendel chose his subject carefully

Why Mendel Succeeded. Why Mendel Succeeded. Mendel chose his subject carefully. Mendel chose his subject carefully. Mendel chose his subject carefully Why Mendel Succeeded I was no unil he mid-nineeenh cenury ha Gregor Mendel, an Ausrian monk, carried ou imporan sudies of herediy he passing on of characerisics from parens o offspring. Characerisics ha

More information

t Instruction Manual GAS BBQ "Bloomfield" Version 2017, Item No. 3160UK

t Instruction Manual GAS BBQ Bloomfield Version 2017, Item No. 3160UK Insrucion Manual GAS BBQ "Bloomfield" Version 2017, Iem No. 3160UK Conens Before using he device... 4 Scope of delivery... 4 Inended use... 5 For your safey... 5-6 Signal symbols... 5 General safey insrucions...

More information

Engineer Programming Quick Guide

Engineer Programming Quick Guide 2 EN50131-1:2006+A1:2009 EN50131-3:2009 EN50131-6:2008 EN50131-5-3:2005+A1:2008 Securiy Grade 2 Environmenal Class II Engineer Programming Quick Guide INTERNAL SIREN WARNING The Enforcer 32-WE conrol panel

More information

Q7300L Series 2000 Commercial Thermostat Subbases

Q7300L Series 2000 Commercial Thermostat Subbases Q700L Series 2000 Commercial hermostat Subbases INSALLAION INSRUCIONS APPLICAION he Q700L hermostat Subbase is used with the 700D,F hermostat to provide electronic control of commercial 24 Vac single zone

More information

Doepke. ProLine NG. Configuration Software for the Dupline Bus System. User Manual. ProLine NG Version 1.20 and newer. May 2010, Version 1.

Doepke. ProLine NG. Configuration Software for the Dupline Bus System. User Manual. ProLine NG Version 1.20 and newer. May 2010, Version 1. Doepke ProLine NG Configuraion Sofware for he Dupline Bus Sysem User Manual ProLine NG Version 1.20 and newer May 2010, Version 1.03 ProLine NG Configuraion Sofware for he Dupline Bus Sysem User Manual

More information

etron M100

etron M100 Регулятор процесса etron M00 www.jumo.n-r.ru По вопросам продаж и поддержки обращайтесь: Архангельск (882)63-90-72 Астана +7(772)727-32 Белгород (4722)40-23-64 Брянск (4832)59-03-52 Владивосток (423)249-28-3

More information

UltraCella. Electronic control for Cold Rooms. User manual NO POWER & SIGNAL CABLES TOGETHER READ CAREFULLY IN THE TEXT!

UltraCella. Electronic control for Cold Rooms. User manual NO POWER & SIGNAL CABLES TOGETHER READ CAREFULLY IN THE TEXT! UlraCella Elecronic conrol for Cold Rooms User manual NO POWER & SIGNAL CABLES TOGETHER READ CAREFULLY IN THE TEXT! H i g h E f f i c i e n c y S o l u i o n s WARNING DISPOSAL CAREL developed is producs

More information

RONALD G. BILLY JR. THIS ADDENDUM CONSISTS OF THREE (3) PAGES AND ATTACHMENTS:

RONALD G. BILLY JR. THIS ADDENDUM CONSISTS OF THREE (3) PAGES AND ATTACHMENTS: Lincolnshire Place Memory Care Facility - Muncie 00 000 7-60 ADDENDUM # ADDENDUM #0 O: ALL BIDDERS RE: CHANGES O PROJEC MANUAL AND DRAWINGS DAED /8/8 DAE: MARCH 9, 08 SUBJEC: LINCOLNSHIRE PLACE MEMORY

More information

Compressed Air Dryers

Compressed Air Dryers Filers for he Food Indusry Balson Balson offers boh membrane and PSA echnology. Balson Membrane combine superior coalescing echnology wih a proven, innovaive membrane sysem o supply clean, dry compressed

More information

Q7300H Series 2000 Commercial Thermostat Subbases

Q7300H Series 2000 Commercial Thermostat Subbases Q700H Series 000 Commercial hermostat Subbases INSALLAION INSRUCIONS APPLICAION he Q700H hermostat Subbases are used with 700F hermostats to provide electronic control of commercial Vac single or multistage

More information

www.lessonplansinc.com opic: Mendel Pea Plan Workshee Summary: Sudens will learn how Mendel discovered classical geneics using pea plans. Sudens will simulae how alleles express alernae versions of genes

More information

L4188A,B; L4189A,B; L6188A-C; L6189A-C Aquastat Controllers

L4188A,B; L4189A,B; L6188A-C; L6189A-C Aquastat Controllers L488A,B; L489A,B; L688A-C; L689A-C Aquastat Controllers PRODUC DAA FEAURES Remote Bulb with Screwdriver Slot APPLICAION Direct Mount with Setting Knob L488 and L489 provide spst switching for high and

More information

Analysis on the Operating Characteristics of a Household Dehumidifier

Analysis on the Operating Characteristics of a Household Dehumidifier Purdue Universiy Purdue e-pubs Inernaial Refrigerai and Air Cdiiing Cference School of Mechanical Engineering 24 Analysis he Operaing Characerisics of a Household Dehumidifier Hg Qi Li Beijing Universiy

More information

INSTALLATION AND USERS GUIDE

INSTALLATION AND USERS GUIDE MINI MEL'S - SAVI MELODY & SOL (COLOR)-"P" SERIES INSALLAION AND USERS GUIDE FOR INDEPENDEN USE OR WIH PENAIR CONROLS or ZODIAC 1 ouch Rev.1 CONROLS WARNING: DO NO USE IN JUNCION WIH ANY PENAIR LIGH -

More information

Contents Page. Page: 2

Contents Page. Page: 2 Conens Page Conens Page... 2 A. Operaing he PCX 46 App... 3 B. Enering Engineers Menu... 4 1. Engineers Menu: Dae + Time... 4 2. Engineers Menu: Learn Wireless Devices... 4 3. Engineers Menu: Program Inpus...

More information

ADVANCED TAPCHANGER CONTROL TO COUNTERACT POWER SYSTEM VOLTAGE INSTABILITY

ADVANCED TAPCHANGER CONTROL TO COUNTERACT POWER SYSTEM VOLTAGE INSTABILITY 1 ADVANCED TAPCHANGER CONTROL TO COUNTERACT POWER SYSTEM VOLTAGE INSTABILITY Zoran Gajiş zoran.gajic@se.abb.com Samir Aganoviş samir.aganovic@se.abb.com ABB AB, Subsaion Auomaion Producs, SE-721 59 Vaseras,

More information

MODEL CW MANUFACTURER WATER CLOSET ADA COMPLIANT AMERICAN STANDARD (OR APPROVED EQUAL) CHAMPION PRO 211AA.104 CADET PEDESTAL SINK

MODEL CW MANUFACTURER WATER CLOSET ADA COMPLIANT AMERICAN STANDARD (OR APPROVED EQUAL) CHAMPION PRO 211AA.104 CADET PEDESTAL SINK DESCRIPION MANUFACURER PLUMBING FIXURE SCHEDULE RESIDENCE MODEL CW CONNECIONS HW WASE VEN NOES 0220 BID SE Addendum # WC WAER CLOSE ADA COMPLIAN AMERICAN SANDARD CHAMPION PRO 2AA.0 /2" 3" 2" VIREOUS CHINA,

More information

UNIVERSAL QUERSTROMZERSPANER UNI-CUT Series QZ

UNIVERSAL QUERSTROMZERSPANER UNI-CUT Series QZ UNIVERSAL QUERSTROMZERSPANER UNI-CUT Series QZ UNI-CUT Series QZ powerful, flexible UNIVERSAL QUERSTROMZERSPANER DRIVE POWER kw 1 WEIGHT DRUM Diameer / heigh mm THROUGHPUT RATES/ h Refrigeraors Elecronics

More information

MTS 5100 Media Test Set. Mini OTDR and Optical Test Set for Fiber Networks. Wavetek MTS-5100 Specs Provided by

MTS 5100 Media Test Set. Mini OTDR and Optical Test Set for Fiber Networks. Wavetek MTS-5100 Specs Provided by MTS 5100 Media Tes Se Mini OTDR and Opical Tes Se for Fiber Neworks Waveek MTS-5100 Specs Provided by www.aaatesers.com MTS 5100 Media Tes Se Advanced Tools for Advanced Services Waveek Fiber Opic Tes

More information

Q7100A,C Thermostat Subbases

Q7100A,C Thermostat Subbases Q700A,C hermostat Subbases INSALLAION INSRUCIONS APPLICAION he Q700 hermostat Subbases provide electronic control of commercial 4 Vac single or multistage heat pump or conventional heating and cooling

More information

PADDY DRYING IN A VIBRATION-ASSISTED VACUUM INFRARED DRYER

PADDY DRYING IN A VIBRATION-ASSISTED VACUUM INFRARED DRYER PADDY DRYING IN A VIBRATION-ASSISTED VACUU INFRARED DRYER Jiraporn Sripinyowanich JONGYINGCHAROEN1, Sahawa THANIKARN2 and *Paarachai VICHAIYA 1 1 Curriculum of Agriculural Engineering, Faculy of Engineering,

More information

THE EFFECTIVENESS OF FIRE DETECTION SYSTEMS IN DIFFERENT DIMENSIONS ÚČINNOSŤ SYSTÉMOV POŽIARNEJ DETEKCIE V RÔZNYCH ROZMEROCH

THE EFFECTIVENESS OF FIRE DETECTION SYSTEMS IN DIFFERENT DIMENSIONS ÚČINNOSŤ SYSTÉMOV POŽIARNEJ DETEKCIE V RÔZNYCH ROZMEROCH THE EFFECTIVENESS OF FIRE DETECTION SYSTEMS IN DIFFERENT DIMENSIONS Agoson RESTAS ÚČINNOSŤ SYSTÉMOV POŽIARNEJ DETEKCIE V RÔZNYCH ROZMEROCH Absrac Inroducion: There are many ways of fire deecion; in many

More information

ASHRAE Standard Solutions Guide. Real-World Applications and Single Source Compliance Strategies

ASHRAE Standard Solutions Guide. Real-World Applications and Single Source Compliance Strategies ASHRAE Sandard 90.1 2010 Soluions Guide Real-World Applicaions and Single Source Compliance Sraegies Levion Excellence For ASHRAE Sandards ASHRAE Sandard 90.1 2010 provides he minimum requiremens for

More information

Q7100A,C,D Thermostat Subbases

Q7100A,C,D Thermostat Subbases Q700A,C, hermostat Subbases INSALLAION INSRUCIONS APPLICAION he Q700 hermostat Subbases provide electronic control of commercial Vac single or multistage heat pump or conventional heating and cooling systems.

More information

O-6. Mechanical 008 REFER TO ENLARGED MECHANICAL ROOM PLAN. Electrical. Basement Storage. Hallway 009. Theater Storage 010 TYPICAL CEILING MOUNTED

O-6. Mechanical 008 REFER TO ENLARGED MECHANICAL ROOM PLAN. Electrical. Basement Storage. Hallway 009. Theater Storage 010 TYPICAL CEILING MOUNTED O- O- O-3 O-4 O-5 O-5b O-6 O-7 DUC-MOUNED ELECRIC HEAING COIL Vault 006 H UP Stair 0 UP EGRESS DOOR HE EISING UILDING (ECEP FOR HE AUDIORIUM) WILL E SUPPLIED EMPERED VENILAION SERVED Y AHU-. EACH OCCUPIED

More information

Stainless Steel Condensing Boiler Connection Instructions To Additional Heating Devices

Stainless Steel Condensing Boiler Connection Instructions To Additional Heating Devices Stainless Steel Condensing Boiler Connection Instructions o Additional Heating Devices Kit #55002875 Kit installation shall be completed by qualified agency.! WARNING Fire, explosion, asphyxiation and

More information

R8888A,B Hydronic Circulator Zone Panels with Priority Control

R8888A,B Hydronic Circulator Zone Panels with Priority Control A,B Hydronic Circulator Zone Panels with Priority Control EAURES PRODUC DAA APPLICAION he A,B Hydronic Circulator Zone Panels with Priority Control provide relay switching for multizone hot water control

More information

Highly efficient heat dissipation units using free cooling. Free Line. You can count on us...

Highly efficient heat dissipation units using free cooling. Free Line. You can count on us... You can coun on us... Highly efficien hea dissipaion unis using free cooling Reliable and energy-saving soluions o proec your invesmens HANSA is a member of he associaion of manufacurers for air condiioning

More information

Performance Rating of Central Station Air-handling Unit Supply Fans

Performance Rating of Central Station Air-handling Unit Supply Fans AHRI Sandard 430 (I-P) 2014 Sandard for Performance Raing of Cenral Saion Air-handling Uni Supply Fans IMPORTANT SAFETY DISCLAIMER AHRI does no se safey sandards and does no cerify or guaranee he safey

More information

L4006,7,8; L6006,7,8 Aquastat Controllers

L4006,7,8; L6006,7,8 Aquastat Controllers L4006,7,8; L6006,7,8 Aquastat Controllers FOR SURFACE MOUNING GENERAL FOR VERICAL MOUNING AND HORIZONAL SENSOR INSERION WIH REMOE BULB FEAURES PRODUC DAA L4006,7 and 8 provide spst switching for high or

More information

International Journal of Engineering Research & Science (IJOER) ISSN: [ ] [Vol-2, Issue-10, October- 2016]

International Journal of Engineering Research & Science (IJOER) ISSN: [ ] [Vol-2, Issue-10, October- 2016] Model developmen of unenable condiions during egress and sochasic evaluaion in comparmen fires Bai-Nian Zhou 1, Yi-Chun Lin 2*, Yuan-Shang Lin 3 1 Fire Service and Disaser Prevenion Advocae Managemen,

More information

MECHANICAL LINETYPE LEGEND MINIMUM MISC MISCELLANEOUS MEDIUM PRESSURE STEAM RETURN MEDIUM PRESSURE STEAM SUPPLY NOT TO SCALE OUTSIDE AIR

MECHANICAL LINETYPE LEGEND MINIMUM MISC MISCELLANEOUS MEDIUM PRESSURE STEAM RETURN MEDIUM PRESSURE STEAM SUPPLY NOT TO SCALE OUTSIDE AIR XX XX H C S F/S NOES: SYMBOL LEGEND 1. ALL SYMBOLS MAY NO APPLY. CODED PLAN NOE EQUIPMEN AION POIN OF CONNECION HUMIDISA CO2 SENSOR RECANGULAR SPLY DUC RISER RECANGULAR REURN DUC RISER RECANGULAR EXHAUS

More information

Product Manual SZ2182

Product Manual SZ2182 Product Manual SZ1 Advanced Air Handling Unit Controller Description he SZ1 is designed to control constant volume and variable air volume air handling units that require advanced control functionality

More information

Study on the quantitative feasibility of rainwater harvesting in small islands

Study on the quantitative feasibility of rainwater harvesting in small islands Sudy on he quaniaive feasibiliy of rainwaer harvesing in small islands Jaehong Ki 1, Mooyoung Han 2 1 Seoul Naional Universiy, Korea, marchsixh@naver.com 2 Seoul Naional Universiy, Korea, myhan@snu.ac.kr

More information

Aesculap Orthopaedics Hip Platform - USA

Aesculap Orthopaedics Hip Platform - USA Aesculap Orhopaedics Hip Plaform USA Page Page Page 6 Page Page Page Page 9 nsrucions for use/technical descripion Orhopedic and Traumaology nsrumen Ses nsrucions for use/technical descripion Ben cup nserion

More information

Memorial Plastic Surgery

Memorial Plastic Surgery enant Improvements 24080 Hwy 59 N Suite 75 Kingwood, 77339 el.: 28/358-0964 www.kaim-inc.com Memorial Plastic Surgery Physician Clinic & Office ased Procedures CFI Companies Medix, LLC Evergreen echnology

More information

mini-kool series INSTALLATION, OPERATION & MAINTENANCE rev 05/01

mini-kool series INSTALLATION, OPERATION & MAINTENANCE rev 05/01 mini-kool series INSALLAION, OPERAION & MAINENANCE 80806-1 rev 05/01 ABLE OF CONENS INRODUCION... 1 PRODUC OVERVIEW... 1 he mini-kool self contained unit... 1 hermostat / Controllers... 2 Seawater pump...

More information

Conductivity Network Sensor

Conductivity Network Sensor Installation and Operation Manual For Boiler-Feed Chemical Monitoring Applications Network Sensor 4VDC Power Source Meter 4 5 6 Network X X X LINE NEURAL GND 4-0mA Interface Warning his Heat-imer sensor

More information

Complex constrained CA urban model: Long-term urban form prediction for Beijing metropolitan area

Complex constrained CA urban model: Long-term urban form prediction for Beijing metropolitan area LONG, Ying; SHEN, Zhenjiang; DU, Liqun, Complex consrained CA urban model 44 h ISOCARP Congress 2008 Complex consrained CA urban model: Long-erm urban form predicion for Beijing meropolian area 1 Inroducion

More information

The Curators of the University of Missouri

The Curators of the University of Missouri Page of ADDENDUM # DAE: November 7, 07 O CONRAC DOCUMENS ENILED: Memorial Student Union Maintenance Repairs & Second Floor Renovation to North Wing; Life Safety Upgrades to North, South, & AP Green Chapel

More information

Significant Earnings Growth Opportunities. Christopher Coughlin Executive Vice President and CFO

Significant Earnings Growth Opportunities. Christopher Coughlin Executive Vice President and CFO Significan Earnings Growh Opporuniies Chrisopher Coughlin Execuive Vice Presiden and CFO February 13, 2008 Tyco_Inernaional_SHOW_FILE_FINAL.pp ForwardLooking Saemen/ NonGAAP Measures This presenaion conains

More information

Product Manual SZ2161. Description The SZ2161 is a microprocessor-based controller designed for water source heat pump plant control applications.

Product Manual SZ2161. Description The SZ2161 is a microprocessor-based controller designed for water source heat pump plant control applications. Product Manual SZ2161 Heat Pump Water Loop Controller Description he SZ2161 is a microprocessor-based controller designed for water source heat pump plant control applications. Features Stand-alone or

More information

Winner: Traditional Home. Delicately Detailed

Winner: Traditional Home. Delicately Detailed Winner: Tradiional Home Delicaely Deailed Peer and Les Adamson s new ligh-filled home combines a perfecly deailed period exerior wih simple, elegan open plan ineriors. Words: Michael Holmes Phoography:

More information

FIREYE EPD260, EPD261, EPD270 PROGRAMMER MODULES

FIREYE EPD260, EPD261, EPD270 PROGRAMMER MODULES EPD-201 AUGUS, 200 FIREYE EPD20, EPD21, EPD20 PROGRAER ODULES AN ALERNAIVE PROGRAER FOR USE WIH HE FLAE-ONIOR SYSE DESCRIPION he Fireye EPD20, EPD21, and EPD20 Programmer odules are used with the FLAE-ON-

More information

SOLAR FEATURES TANK FEATURES

SOLAR FEATURES TANK FEATURES SOLAR GAS BACKUP INEGRAED SOLAR & HIGH EFFICIENCY GAS BACKUP WAER HEAERS he Solar Gas Backup blends all of the features of the Ultra Force high efficiency gas water heater with a storage tank optimized

More information

Treasure every moment

Treasure every moment Treasure every momen Imagine fresh omaoes from he communiy garden. Blue Mounains views from a peaceful hillop park. Local markes and café cach-ups in a hriving own cenre conneced o Schofields rain saion.

More information

Translation of Extended Petri Net Model into Ladder Diagram and Simulation with PLC

Translation of Extended Petri Net Model into Ladder Diagram and Simulation with PLC rojniški vesnik - Journal of Mechanical Engineering 55(009)0, 608-6 Paper receive: 0.05.009 UDC 68.5 Paper accepe: 5.09.009 Translaion of Exene Peri Ne Moel ino Laer Diagram an imulaion wih PLC Tomaž Perme

More information

CAUTION: ELECTRICAL HAZARD

CAUTION: ELECTRICAL HAZARD R R Installation Guide 53DF50-HW hermostat System ypes Cool Only (single stage) Heat Pump (with electric heat) CAUION: ELECRICAL HAZARD Can cause electrical shock or equipment damage. Disconnect power

More information

DESIGN OF LOW POWER FFT PROCESSORS USING MULTIPLIER LESS ARCHITECTURE

DESIGN OF LOW POWER FFT PROCESSORS USING MULTIPLIER LESS ARCHITECTURE DESIGN OF LOW POWER FFT PROCESSORS USING MULTIPLIER LESS ARCHITECTURE Senhil Sivakumar M., Gurumekala T. 2, Sundaram A. 3, Thandaiah Prabu R. 4, Arpuharaj T. 5 and Banupriya M. 6 Deparmen of Elecronics,

More information

SLIDE-IN HEATING COIL INSTALLATION MANUAL BULLETIN

SLIDE-IN HEATING COIL INSTALLATION MANUAL BULLETIN SLIDE-IN HEAING COIL INSALLAION MANUAL BULLEIN 30-030 ABLE OF CONENS Installation Specifications... 3 INRODUCION... 3 INSALLAION... 3 PIPING... 6 FREEZE PROECION... 6 WIRING AND CONROLS... 6 SARUP... 7

More information

Evaluation of the drying methods and conditions with respect to drying kinetics, colour quality and specific energy consumption of thin layer pumpkins

Evaluation of the drying methods and conditions with respect to drying kinetics, colour quality and specific energy consumption of thin layer pumpkins Bulgarian Chemical Communicaions, Volume 48, Number3 (pp. 480 491) 016 480 Evaluaion of he drying mehods and condiions wih respec o drying kineics, colour qualiy and specific energy consumpion of hin layer

More information

Due to possibility of personal injury or property damage, always contact an authorized technician for servicing or repair of this unit.!

Due to possibility of personal injury or property damage, always contact an authorized technician for servicing or repair of this unit.! echnical Information- Dishwasher JD51AWP RJDW7A Due to possibility of personal injury or property damage, always contact an authorized technician for servicing or repair of this unit.! CAUION All safety

More information

Morgan Stanley Global Industrials CEOs Unplugged Conference

Morgan Stanley Global Industrials CEOs Unplugged Conference Morgan Sanley Global Indusrials CEOs Unplugged Conference Ed Ardie Sr. Vice Presiden, Sraegy & Invesor Relaions George Oliver Presiden, Safey Producs Sepember 11, 2008 Tyco_Inernaional_SHOW_FILE_FINAL.pp

More information

3.4 SPINDLE AMPLIFIER MODULE

3.4 SPINDLE AMPLIFIER MODULE 3. TROUBLESHOOTING AND 3. ACTION TO BE TAKEN TROUBLESHOOTING B 65165E/01 3.4 SPINDLE AMPLIFIER MODULE If an alarm occurs in the spindle amplifier module, the ALM LED lights red in the STATUS display, and

More information

MODEL Day Programmable 1 Heat / 1 Cool Electric / Gas

MODEL Day Programmable 1 Heat / 1 Cool Electric / Gas ELECRONIC HERMOSAS MODEL 8353 5-2 Day Programmable 1 Heat / 1 Cool Electric / as User s Manual Installation and Programming Installation uide IMPORAN SAFE INFORMAION ARNIN: Always turn off power at the

More information

ADA 100 OPERATIONS & INSTALLATION MANUAL

ADA 100 OPERATIONS & INSTALLATION MANUAL ADA 00 AREA OF RESCUE SYSEM VERSION.a OPERAIONS & INSALLAION MANUAL HOUSING DEVICES, INC 0R MYSIC AVE. MEDFORD, MA 0 0000 ABLE OF CONENS INRODUCION Page SYSEM DESCRIPION Page SYSEM OPERAION Page MASER

More information

Chromatographic Detectors and Column Holdup for Organics PDMS Systems

Chromatographic Detectors and Column Holdup for Organics PDMS Systems Irnaional Conference on Innovaions in Chemical Engiering and edical Sciences (ICICES'01) December 6-7, 01 Dubai (UAE) Chromaographic Deecors and Column Holdup for Organics PDS Sysems Edison uzenda Absrac

More information

RESIDENTIAL & GARDEN LIGHTS

RESIDENTIAL & GARDEN LIGHTS RESIDENTIAL & GARDEN LIGHTS PAGE 122 PAGE 123 PAGE 126 PAGE 131 PAGE 135 PAGE 138 4 Wide range of ligh fiings, mosly IP raed for exernal domesic applicaions covering lanerns, wall lighs, deck lighs and

More information

S BV NW BEDDINGTON TR NE CENTRE ST N 4 ST NW 16 AV NW 17 AV SW 9 AV SE 33 AV SW 42 AV SE 50 AV S CROWCHILD TR NW 58 AV SE HERITAGE DR SW

S BV NW BEDDINGTON TR NE CENTRE ST N 4 ST NW 16 AV NW 17 AV SW 9 AV SE 33 AV SW 42 AV SE 50 AV S CROWCHILD TR NW 58 AV SE HERITAGE DR SW 14 ST SW MACLEOD SE CROWCHILD SW SARCEE SW 37 ST SW 4 ST 14 ST SW Amended: 19P2017 HWY 772 144 AV A SIMONS VALLEY Y P COUNY HILL S BV HARV E ST HIL LS BV N DEERFOOT NE 128 AV NE COUNY HILLS BV NE NOSEHILL

More information

Description / Applications

Description / Applications PARS & ACCESSORIES Description / Applications he Beckett AquaSmart is an advanced boiler control designed for use on residential and light commercial boiler systems. All models include the option of enabling

More information

Issue 1 (37), 2018 ISSN CHOICE OF MIXTURES OF AGENTS IN HEAT PUMPS FOR HEATING AND COOLING MEDIA WITH LIMITED CAPACITY

Issue 1 (37), 2018 ISSN CHOICE OF MIXTURES OF AGENTS IN HEAT PUMPS FOR HEATING AND COOLING MEDIA WITH LIMITED CAPACITY Issue 1 (37), 2018 ISSN 2542-0526 UDC 6216036 A L Shurais 1, A V Rulev 2, E Yu Usacheva 3 CHOICE OF MIXTURES OF AGENTS IN HEAT PUMPS FOR HEATING AND COOLING MEDIA WITH LIMITED CAPACITY JSC «Giproniigaz»

More information

GCL design series Part 1: GCL performance as a fluid barrier

GCL design series Part 1: GCL performance as a fluid barrier Designer s Forum GCL design series Par 1: GCL performance as a fluid barrier By Richard B. Erickson, Richard Thiel, P.E., and Gregory N. Richardson, P.E., Ph.D. Over he pas 18 monhs, GSE in conjuncion

More information

STUD IES ON HEAT PUMP DRY ING OF THOMSON SEED LESS GRAPES (Vitis Vinifera) FOR THE PRO DUC TION OF RAI SINS

STUD IES ON HEAT PUMP DRY ING OF THOMSON SEED LESS GRAPES (Vitis Vinifera) FOR THE PRO DUC TION OF RAI SINS Progressive Research An Inernaional Journal Prin ISSN : 973-647, Online ISSN : 2454-63 Volume (Special-V) : 7-77, (25) Sociey for Scienific Developmen in Agriculure and Technology Meeru (U.P.) INDIA STUD

More information

DCS-3000 AutoCure Operating Manual

DCS-3000 AutoCure Operating Manual DCS-3000 AutoCure Operating Manual DCS-3000 AutoCure Control System 2011 110707 page 1 ABLE OF CONENS 1. Overview 2. AutoCure operation 3. Casing control 4. Set Up (Changing the way the instrument works)

More information

[Aggarwal, 5(8): August 2018] ISSN DOI /zenodo Impact Factor

[Aggarwal, 5(8): August 2018] ISSN DOI /zenodo Impact Factor [Aggarwal, 5(8): Augus 2018] ISSN 2348 8034 DOI- 10.5281/zenodo.1339350 Impac Facor- 5.070 GLOBAL JOURNAL OF ENGINEERING SCIENCE AND RESEARCHES ELZAKI TRANSFORM OF BESSEL S FUNCTIONS Sudhanshu Aggarwal

More information

ARGO AR SERIES CONTROLS

ARGO AR SERIES CONTROLS ARGO AR SERIES CONROLS AR822-II, AR861-2II, AR861-3II INSALLAION, OPERAION & MAINENANCE MANUAL AR861-2II AR822-II AR861-3II Information and specifications outlined in this manual in effect at the time

More information

Description / Applications

Description / Applications PARS & ACCESSORIES Description / Applications he Beckett AquaSmart is an advanced boiler control designed for use on residential and light commercial boiler systems. All models include the option of enabling

More information

STRIP COMMERCIAL AND MIXED-USE DEVELOPMENT

STRIP COMMERCIAL AND MIXED-USE DEVELOPMENT STRIP COMMERCIAL AND MIXED-USE DEVELOPMENT IN HILLSBOROUGH COUNTY Draf Augus 2014 Hillsborough Couny Ciy-Couny Planning Commission 601 E. Kennedy Boulevard, 18 h Floor Tampa, Florida 33602 Dover, Kohl

More information