AFP-300/AFP-400 Analog Fire Panel

Transcription

1 12 Clintonville Road Northford, CT (203) (203) (Fax) AFP-300/AFP-400 Analog Fire Panel Operations Manual Document /22/97 Revision: C PN 50260:C1 ECN Technical Manuals line! -

2 Installation Precautions - Adherence to the following will aid in problem-free installation with long-term reliability: WARNING - Several different sources of power can be connected to the fire alarm control panel. Disconnect all sources of power before servicing. Control unit and associated equipment may be damaged by removing and/or inserting cards, modules, or interconnecting cables while the unit is energized. Do not attempt to install, service, or operate this unit until this manual is read and understood. CAUTION - System Reacceptance Test after Software Changes: To ensure proper system operation, this product must be tested in accordance with NFPA Chapter 7 after any programming operation or change in site-specific software. Reacceptance testing is required after any change, addition or deletion of system components, or after any modification, repair or adjustment to system hardware or wiring. All components, circuits, system operations, or software functions known to be affected by a change must be 100% tested. In addition, to ensure that other operations are not inadvertently affected, at least 10% of initiating devices that are not directly affected by the change, up to a maximum of 50 devices, must also be tested and proper system operation verified. This system meets NFPA requirements for operation at 0-49 O C/ O F and at a relative humidity of 85% RH (non-condensing) at 30 O C/86 O F. However, the useful life of the system's standby batteries and the electronic components may be adversely affected by extreme temperature ranges and humidity. Therefore, it is recommended that this system and its peripherals be installed in an environment with a nominal room temperature of O C/60-80 O F. Verify that wire sizes are adequate for all initiating and indicating device loops. Most devices cannot tolerate more than a 10% I.R. drop from the specified device voltage. Like all solid state electronic devices, this system may operate erratically or can be damaged when subjected to lightning induced transients. Although no system is completely immune from lightning transients and interferences, proper grounding will reduce susceptibility. Overhead or outside aerial wiring is not recommended, due to an increased susceptibility to nearby lightning strikes. Consult with the Technical Services Department if any problems are anticipated or encountered. Disconnect AC power and batteries prior to removing or inserting circuit boards. Failure to do so can damage circuits. Remove all electronic assemblies prior to any drilling, filing, reaming, or punching of the enclosure. When possible, make all cable entries from the sides or rear. Before making modifications, verify that they will not interfere with battery, transformer, and printed circuit board location. Do not tighten screw terminals more than 9 in-lbs. Over tightening may damage threads, resulting in reduced terminal contact pressure and difficulty with screw terminal removal. This system contains static-sensitive components. Always ground yourself with a proper wrist strap before handling any circuits so that static charges are removed from the body. Use static suppressive packaging to protect electronic assemblies removed from the unit. Follow the instructions in the installation, operating, and programming manuals. These instructions must be followed to avoid damage to the control panel and associated equipment. FACP operation and reliability depend upon proper installation. Fire System Limitations While installing a fire alarm system may make lower insurance rates possible, it is not a substitute for fire insurance! An automatic fire alarm system - typically made up of smoke detectors, heat detectors, manual pull stations, audible warning devices, and a fire alarm control with remote notification capability can provide early warning of a developing fire. Such a system, however, does not assure protection against property damage or loss of life resulting from a fire. Any fire alarm system may fail for a variety of reasons: Smoke detectors may not sense fire where smoke cannot reach the detectors such as in chimneys, in walls, or roofs, or on the other side of closed doors. Smoke detectors also may not sense a fire on another level or floor of a building. A second floor detector, for example, may not sense a first floor or basement fire. Furthermore, all types of smoke detectors - both ionization and photoelectric types, have sensing limitations. No type of smoke detector can sense every kind of fire caused by carelessness and safety hazards like smoking in bed, violent explosions, escaping gas, improper storage of flammable materials, overloaded electrical circuits, children playing with matches, or arson. IMPORTANT! Smoke detectors must be installed in the same room as the control panel and in rooms used by the system for the connection of alarm transmission wiring, communications, signaling, and/or power. If detectors are not so located, a developing fire may damage the alarm system, crippling its ability to report a fire. Audible warning devices such as bells may not alert people if these devices are located on the other side of closed or partly open doors or are located on another floor of a building. A fire alarm system will not operate without any electrical power. If AC power fails, the system will operate from standby batteries only for a specified time. Rate-of-Rise heat detectors may be subject to reduced sensitivity over time. For this reason, the rate-of-rise feature of each detector should be tested at least once per year by a qualified fire protection specialist. Equipment used in the system may not be technically compatible with the control. It is essential to use only equipment listed for service with your control panel. Telephone lines needed to transmit alarm signals from a premise to a central monitoring station may be out of service or temporarily disabled. The most common cause of fire alarm malfunctions, however, is inadequate maintenance. All devices and system wiring should be tested and maintained by professional fire alarm installers following written procedures supplied with each device. System inspection and testing should be scheduled monthly or as required by National and/or local fire codes. Adequate written records of all inspections should be kept. FCC Warning WARNING: This equipment generates, uses, and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual, may cause interference to radio communications. It has been tested and found to comply with the limits for class A computing device pursuant to Subpart B of Part 15 of FCC Rules, which is designed to provide reasonable protection against such interference when operated in a commercial environment. Operation of this equipment in a residential area is likely to cause interference, in which case the user will be required to correct the interference at his own expense. Canadian Requirements This digital apparatus does not exceed the Class A limits for radiation noise emissions from digital apparatus set out in the Radio Interference Regulations of the Canadian Department of Communications. Le present appareil numerique n'emet pas de bruits radioelectriques depassant les limites applicables aux appareils numeriques de la classe A prescrites dans le Reglement sur le brouillage radioelectrique edicte par le ministere des Communications du Canada. Technical Publishing Document PRECAULG.PM6 12/31/96 Technical Manuals line! -

3 Table of Contents 1. Introduction Overview... 1 Operating Features... 1 Components Using the Control Panel Overview... 3 System Status Indicator LEDs... 3 Control Keys Operating Modes Normal Operation... 5 Trouble Operation... 5 Fire... 6 Supervisory Signal... 7 Non- Point Operation... 7 Trouble Monitor Point Operation... 7 Notification Appliance Circuit (NAC) Operation... 8 Control-By-Event Operation... 8 Releasing Functions... 8 Intelligent Detector Functions Pre- Operation (AWACS) Time Functions Overview Operating Coding Functions Presignal/Positive Sequence (PAS) Operation Special System Timers Waterflow Circuits Operation Disable/Enable Operation Style 6 Operation Read Status Overview How to Enter Read Status Read Status Options Read Status for Points and Zones Read Status for a Detector, Module, or Output Read History View History View or Print Hidden History Presignal Delay Releasing Zones Time Control Zones Holiday Zones NAC Coding Zone Pre- Zone System Parameters Annunciator Display Selections Example of Annunciator Display Selections Voice Systems Overview Operating Features In this Section Before you Begin AMG-1/AMG-E Audio Message Generator AMG-1/AMG-E Overview AFP-300/AFP-400 Operations PN 50260:C1 05/22/97 1 Technical Manuals line! -

4 Table of Contents 5. Voice Systems AMG-1/AMG-E Operating Features Operating the AMG Selecting AMG Group Functions Selecting AMG Tones and Messages ATG-2 Audio Tone Generator ATG-2 Overview How to Operate the ATG Selecting Tones for the ATG Selecting a Primary (Evac) Channel Tone Selecting a Secondary (Alert) Channel Tone Select Operating Mode Fire Fighter's Telephones (FFT-7/FFT-7S) Overview FFT-7 Operating Components How to Operate the FFT Audio Amplifiers Overview Audio Amplifier Features AA-30 Audio Amplifiers AA-100/AA-120 Audio Amplifiers Adjusting the Audio Gain Level (AA-30, AA-100/AA-120) Selecting the AA-100/AA-120 Backup Tone AMG Voice Message Options Overview Installation AFP-300/AFP-400 Operations PN 50260:C1 05/22/97 Technical Manuals line! -

5 Overview 1. Introduction The AFP-300/AFP-400 is a modular, intelligent Fire Control Panel (FACP) with an extensive list of powerful features. The CPU module, power supply module, and cabinet combine to create a complete fire control system for most applications. Optional modules mount to the chassis to provide additional output circuits. Operating Features Verification selection per point, with tally. Positive Sequence (PAS) and Presignal per NFPA Silence Inhibit timer and Auto Silence timer. March time/temporal code for Notification Appliance Circuits (NACs). Zone coding for NACs if using an optional UZC-256. Silence/System Reset/ Activate functions through MMX monitor modules. Automatic time-of-day and day-of-week control functions, with holiday option. User-defined password and key-protected nonvolatile memory. AWACS (Advanced Warning Addressable Combustion Sensing) with nine fieldadjustable Pre- levels with programmable Control-by-Event (CBE) Operate automatic smoke or heat detector sounder base on action Pre- level, with general evacuation on alarm level. Security alarm point option with separate audible signal code. Centralized voice paging and audible alarm signaling options. Programmable Control-by-Event control of outputs from individual alarm or supervisory addressable devices. Components Figure 1 shows components that affect operation of the control panel: EIA-232 PC/Terminal Port EIA-232 Printer Port EIA-485 Terminal Mode Port EIA-485 ACS Port 80-character (2 x 40) Liquid Crystal Display (LCD) Programming Keypad System Status LED Indicators Control Keys Figure 1 Control Panel Components AFP-300/AFP-400 Operations PN 50260:C1 05/22/97 1 Technical Manuals line! -

6 Notes 2 AFP-300/AFP-400 Operations PN 50260:C1 05/22/97 Technical Manuals line! -

7 2. Using the Control Panel Overview Table 1 lists the controls and indicators and where to find information on their use: Controls/Indicators Covered in... Eight System Status Indicator LEDs System Status Indicator LEDs on page 3. Five control keys Control Keys on page 4. A panel sounder with a piezo that provides unique sounds for alarm, trouble and supervisory/security conditions Section 3. Operating Modes on page 5. System Status Indicator LEDs Table 1 Control and Indicators The control panel contains eight LED indicators with labels as shown in Figure 2: Figure 2 System Status Indicator LEDs Table 2 contains descriptions of the System Status Indicator LEDs: Indicator Color When Active... To Turn... AC Power Green Lights when the proper primary AC power is applied. Fire Red Flashes when a non-acknowledged Fire exists. Lights steadily after you acknowledge the alarm. Turn off AC power. Clear the alarm condition and reset the system. Pre- Warning Yellow Flashes when a non-acknowledged Pre- exists. Lights steadily after you acknowledge the Pre-. Clear the alarm condition. (Action Pre- requires a system reset.) Security Blue Flashes when a non-acknowledged Security exists. Lights steadily after you acknowledge the alarm. Clear the Security condition and reset the system. Supervisory Signal Yellow Flashes when a non-acknowledged Supervisory exists. Lights steadily after you acknowledge the alarm. Clear the signal. (Tamper inputs require a system reset.) System Trouble Yellow Flashes when a non-acknowledged System Trouble exists. Lights steadily after you acknowledge the trouble. Clear the trouble condition. Disabled Points Yellow Lights when one or more system devices are disabled. Enable or remove the disabled device. Silenced Yellow Lights after an alarm condition occurs and after pressing < Silence>. Press < Activate> or <System Reset>. Table 2 Descriptions of System Status Indicator LEDs AFP-300/AFP-400 Operations PN 50260:C1 05/22/97 3 Technical Manuals line! -

8 2. Using the Control Panel Control Keys Control Keys The control panel provides five control keys, Acknowledge/Step, Silence, Activate, System Reset, and Lamp Test. Acknowledge Step Use the <Acknowledge/Step> key to respond to new alarm or trouble signals. Pressing <Acknowledge/Step> causes the control panel to do the following: silence the control panel sounder; change all indicators from flashing to steady; send an Acknowledge message to the history file, an optional printer, and an optional LCD-80; and send a signal to silence the sounder on the LCD-80 and ACS annunciators. You can also press the <Acknowledge/Step> key to display multiple alarms or troubles. If more than one alarm or trouble exists, the control panel displays the next alarm or trouble for 3 seconds (or until you press <Acknowledge/Step>), then displays the next alarm or trouble. Silence Use the < Silence> key to silence the control panel sounder as well as sounders connected to Notification Appliance Circuits. Pressing < Silence> causes the control panel to do the following: turn off the control panel sounder; turn off all silenceable output circuits; light the Silenced LED; and send an Silenced message to the history file, optional printer, and an optional LCD-80. Activate Use the < Activate> key to test notification appliances. Press and hold the Activate switch for 2 seconds (to prevent accidental activation). The control panel does the following: turns on all silenceable NACs; turns off the Silenced LED; and sends a Manual Evacuate message to the history file, optional printer, and an optional LCD-80. System Reset Use the <System Reset> key to reset the control panel. Press <System Reset> and the control panel does the following: turns off all alarm-activated CMX modules and NAC circuits; breaks resettable power to four-wire detectors; and sends an All Systems Normal message to the history file, optional printer, and an optional LCD-80. Any alarm or trouble that exists after a System Reset reactivates NACs, control outputs, and panel audio and visual indicators. Lamp Test Use the <Lamp Test> key to test the control panel LEDs and sounder. Press and hold <Lamp Test> and the control panel does the following: lights all control panel LEDs; turns on the control panel sounder; and lights all segments of the LCD display. 4 AFP-300/AFP-400 Operations PN 50260:C1 05/22/97 Technical Manuals line! -

9 3. Operating Modes Normal Operation The system operates in Normal mode when no alarms or troubles exist. In Normal mode, the control panel displays a system message as follows: YOUR CUSTOM FORTY CHARACTER MESSAGE HERE ALL SYSTEMS NORMAL 11:30A TUE 02/11/97 Figure 3 All Systems Normal Message In Normal mode, the control panel does the following functions at regular intervals: Polls all Signaling Line Circuit (SLC) devices and the four NACs to check for valid replies, alarms, troubles, circuit integrity, and so on. Checks power supply troubles and batteries every 10 seconds. Sends a supervisory query on the LCD-80 and verifies proper response. Refreshes the LCD and the optional LCD-80 display and updates time. Scans the keypad for a System Reset or an Enter key press. Performs a detector automatic test operation. Tests system memory. Trouble Operation The system goes into Trouble mode when the control panel detects an electrical or mechanical fault. With no alarms, a control panel in Trouble mode does the following: Produces a pulsed audible tone; The System Trouble LED flashes; The trouble relay activates (MPS-400, TB3); and Sends a message to the LCD display, an optional LCD-80, an optional printer, and the history file. Figure 4 shows a typical Trouble message: Type of event (trouble) Type of device Custom descriptor for this device location TROUBL PULL STATION I.C.U. WEST WING Z1 INVALID REPLY 11:45PM TUE 02/11/97 Software zone assigned (Zone 1) Type of trouble Time and date Note: CMX modules report both open and short circuit messages. Figure 4 Trouble Message 1. Press <Acknowledge/Step> to silence the panel sounder and switch the System Trouble LED from flashing to steady regardless of the number of troubles, alarms, and supervisory signals. 2. Pressing <Acknowledge/Step> while at least one new alarm or trouble exists, causes the control panel to send an Acknowledge message to the history file and an optional printer. AFP-300/AFP-400 Operations PN 50260:C1 05/22/97 5 Technical Manuals line! -

10 3. Operating Modes Fire If the trouble clears (before or after pressing <Acknowledge/Step>), the control panel sends a Clear Trouble message to the printer. Figure 5 shows a sample Trouble Message: TROUBL CONTROL TROUBL CONTROL MODULE ADDRESS 21 Z00 OPEN CIRCUIT 08:10A 08/20/95 M21 MODULE ADDRESS 22 Z00 OPEN CIRCUIT 08:12A 08/20/95 M22 Figure 5 Sample Trouble Message If all troubles clear and no supervisory or fire conditions exist, the control panel does the following: Returns to Normal mode; Sends an All Systems Normal message to the LCD display, the history file, an optional LCD-80, an optional printer; and Restores troubles automatically even if troubles are not acknowledged. Pressing < Silence> when only troubles exist, gives the same result as pressing <Acknowledge/Step>. The Silenced LED does not light unless an alarm exists in the system. If multiple trouble conditions exist in the system, the LCD and optional LCD-80 displays automatically step through each trouble event every 3 seconds in the following order: 1. s, in order of address; 2. Supervisory, in order of address; or 3. Troubles, in order of address. Press <Acknowledge/Step> and the display stops on the current trouble event for 1 minute. Press <Acknowledge/Step> to continue. Fire The system goes into Fire mode when the control panel detects a fire alarm. During Fire mode, the control panel does the following: Produces a steady audible tone; Activates the System relay (MPS-400, TB3) and flashes the System LED; Displays in the status banner on the LCD display; Latches alarms so they cannot clear until the alarm initiating device returns to its normal condition and the operator resets the control panel; Initiates any Control-by-Event actions; Starts timers (such as Silence Inhibit, Auto Silence); and Activates the general alarm zone (Z00). Status banner ALARM ALARM:PULL STATION I.C.U. WEST WING VISITORS LOUNGE 11:55PM TUE 02/11/97 Figure 6 Fire Display 6 AFP-300/AFP-400 Operations PN 50260:C1 05/22/97 Technical Manuals line! -

11 Supervisory Signal Note: You can program Supervisory signals as Tracking or Latching. Supervisory Signal 3. Operating Modes Supervisory signals cause the control panel to do the following: Produce a warbling audible tone; Turn on the Supervisory relay (MPS-400, TB5) and flash the Supervisory LED; Display Active in the status banner on the control panel; and Turn off the panel sounder for all Silenced alarms. Status banner ACTIVE ACTIVE TAMPER I.C.U. WEST WING VISITORS LOUNGE 11:55PM TUE 02/11/97 Non- Point Operation Figure 7 Typical Supervisory Signal Display Non- points are MMX addressable modules that activate Control-by-Event. These points do not activate the System LED or the panel sounder. Non- points use three type codes: Non-Fire, Hazard Alert, and Fire Control. Type Code Does this... Used for... Non-fire (Tracking) Hazard Alert (Latched) Fire Control (Tracking) Activates Control-by-Event only. Sends a message to the LCD display, history file, printer, and LCD-80 (status Active), and overrides code selection for NACs, regardless of the zone F8 coding selection. Sends messages to the LCD, history file, printer and LCD-80. Energy management or other non-fire situations. Monitoring critical processes or other hazardous situations, such as a tornado. Air handler shutdown, intended to override automatic fire functions. Trouble Monitor Point Operation Table 3 Non- Points Trouble Monitor-type MMX modules monitor remote power supplies or other external equipment. These types of MMX modules operate like troubles but with the following differences: The LCD display status banner displays Active ; The type code is Trouble Mon ; The modules latch until the troubles are returned to normal condition and an operator resets the control panel; and MMX modules can have Control-by-Event. AFP-300/AFP-400 Operations PN 50260:C1 05/22/97 7 Technical Manuals line! -

12 3. Operating Modes Notification Appliance Circuit (NAC) Operation Notification Appliance Circuit (NAC) Operation The four NACs (TB7-TB10 on the MPS-400) have Control-by-Event and trouble functions like CMX addressable modules on the SLC loop. NAC circuits differ from CMX modules in the following ways: Addresses (last three characters in LCD field) are B01, B02, B03, or B04; The default type code field is Bell Circuit ; and Control panel NACs, except those controlled with CMX modules, can be used for coded functions (March Time, California Code, Temporal, and Two-stage). Note: Zones F0-F9 are reserved for special functions such as cross-zoning (refer to the AFP- 300/AFP-400 Programming Manual). Note: Refer to Appendix A in the AFP-300/AFP-400 Programming Manual for more information about releasing functions. Control-By-Event Operation Control-by-event (CBE) control is done through 99 software zones. Each input point (detector, MMX) and output point (CMX, NAC) can be programmed to list up to five software zones. Non- or Supervisory points do not activate software zone Z00 (general alarm). You can list zone Z00 for output points, but you do not need to list Z00 for input points. Input and output devices with listed software zones work as follows: Inputs When an input device (detector or MMX) activates, so do all software zones listed to the input device. Outputs When a software zone activates, the output device turns on. CBE Example Detector D102 lists zone Z05. B01 lists zone Z05 and zone Z Detector D102 activates. 2. Zone Z05 activates. 3. B01 activates. Releasing Functions Overview Zones R0-R9 are reserved for releasing zones providing up to ten independent releasing operations. Each releasing zone includes the following options: Option Description Cross-zoning Select one of three types of cross-zoning. Refer to Table 5. Delay Timer Select a 0 60 second delay before activating a zone. Abort An abort switch-type code used to abort activation of a zone. Manual Release Allows immediate zone activation by overriding the abort function, cross-zone function, and delay timer. Soak Timer Automatically shuts off the releasing device. Select seconds for a Soak Timer or 0000 seconds for no Soak Timer. Table 4 Cross Zoning Options 8 AFP-300/AFP-400 Operations PN 50260:C1 05/22/97 Technical Manuals line! -

13 Releasing Functions 3. Operating Modes Using Cross Zoning Options Cross Zoning lets you program the control panel to activate a releasing zone after two initiating devices are tripped. (If not using Cross Zoning, set CROSS= to N.) Table 5 contains a summary of the types of cross zoning and the conditions for activating a releasing zone. Type Y Z H Activates when... Two or more detectors, all mapped to one of the ten releasing zones (R0-R9), are tripped. Two or more detectors, mapped to two different software zones and one of the ten releasing zones (R0-R9), are tripped. At least one smoke detector and at least one heat detector, all mapped to one of the ten releasing zones (R0-R9), are tripped. Note: ly the first non-special zone listed in the zone map is used to determine Cross=Z. Table 5 Cross Zoning Types Cross Zoning Example Table 6 lists examples of devices mapped to releasing zones (ZR1 stands for Releasing Zone 1). Device Address Device Type Zone Mapping D101 Detector Smoke ZR1 Z01 D102 Detector Smoke ZR1 Z01 D103 Detector Smoke ZR1 Z02 D104 Detector Heat ZR1 Z02 B01 Output Circuit (Rel Ckt) ZR1 Table 6 Devices Mapped to Releasing Zones The following explanations apply to the examples listed in Table 6: Cross=N An alarm from any detector activates the releasing circuit. Cross=Y An alarm from any two detectors activates the releasing circuit. Cross=Z Release requires the activation of two detectors mapped to different zones: D101 and D102 cannot activate the releasing circuit because both detectors are mapped to Z01; D101 and D103 can activate the releasing circuit because they are mapped to different zones. Cross=H Release requires activation of heat detector D104 and one smoke detector (D101, D102, or D103). AFP-300/AFP-400 Operations PN 50260:C1 05/22/97 9 Technical Manuals line! -

14 3. Operating Modes Intelligent Detector Functions Note: For instructions on selecting Intelligent Detector Functions, refer to the AFP-300/AFP-400 Programming Manual. Intelligent Detector Functions Table 7 contains descriptions for intelligent detector functions used with the control panel. Function Description Analog Display Sensitivity Adjust Day/Night Sensitivity Operation Maintenance Alert Automatic Test Operation Type Code Supervision LED Control Operation Verification and Counter Operation The control panel reads and displays analog information from the 198 analog detectors. The display shows the percent of the alarm threshold for each detector. Nine selections for manually setting intelligent detector alarm levels within the UL range. If using Ionization detectors in duct applications, set Sensitivity Adjust to Level 1. You can program the system to automatically force smoke detectors to minimum sensitivity during the day. Refer to Time Control Zones on page 19. When compensation reaches the limit of the amount of drift compensation that can be safely applied, the control panel reports a special trouble condition, per national fire code standards. This condition also activates if the detector remains at very high or very low levels for an extended time. The control panel performs an automatic test of each detector every 256 minutes. Failure to meet the test limits causes an AUTO TEST Fail trouble. The control panel monitors hardware device type codes (CPX, SDX, FDX, LPX, IPX, MMX, and CMX) for each installed device at regular intervals (an interval can take up to 30 minutes for full capacity system). If a mismatch of type compared to the program occurs, the control panel generates a point trouble labelled Invalid Type. A global program selection to prevent detector LEDs from blinking during normal operation. A typical application is a sleeping area where a blinking light can distract people. As a standard function, the control panel allows all LEDs to turn on in alarm. The control panel performs alarm verification on programmed CPX, SDX LPX, and IPX intelligent smoke detectors. The verification time is a global program selection of 0 30 seconds. Each detector includes a verification counter, which displays the number of times that a detector entered verification but did not time-out to alarm. The counter increments to 99 and holds. Table 7 Intelligent Detector Functions 10 AFP-300/AFP-400 Operations PN 50260:C1 05/22/97 Technical Manuals line! -

15 Pre- Operation (AWACS) 3. Operating Modes Note: Refer to the AFP-300/ AFP-400 Programming manual for more information on AWACS applications. Pre- Operation (AWACS) If an SDX or CPX detector exceeds the programmed Pre- level, a Pre- condition occurs: the panel sounder and zone F9 activate; and the Pre- LED lights. Figure 8 shows a sample Pre- message sent to the LCD display, optional LCD-80, optional printer, and history file for a control panel programmed for an Alert Pre-. PREALARM SMOKE (PHOTO) I.C.U WEST WING ALERT 105%/5 12:01A 02/01/97 D101 Shows the detector programmed for ALERT Pre- level. Detector programmed for a Pre- level of 5. Shows the detector has reached 105% of the programmed Pre- level. The 105% is a real-time display and tracks smoke levels. Note: ALERT Pre-s automatically restore. Overview Figure 8 Alert Pre- Message If programming a control panel for an ACTION Pre-, the display remains the same, but the word Action replaces Alert. The control panel latches for ACTION Pre-s and applies the programmed control functions. Time Functions The control panel includes a real-time clock that provides time-of-day, date, and dayof-week. The clock includes a lithium battery backup. Time normally displays in a 12-hour time format with month/day/year. Table 8 contains descriptions and typical uses for time functions. Time Function Time Control Command Day/Night Sensitivity Adjust Holiday Description Zones F5 and F6 are reserved for control-by-time special functions, intended for ancillary (non-fire) applications (such as lighting control, setting a thermostat, and so forth). If a CPX, SDX LPX, or IPX detector CBE lists zone F5 or F6, the control panel sets the detector sensitivity to the minimum (low) setting when zone F5 or F6 is activated by the programmed date/ time in its CBE. When zone F5 or F6 deactivates, the detector sensitivity returns to the programmed setting. The control panel reserves zone F7 for setting holiday dates (up to 9 days). When the current date matches any of the nine holiday dates, the control panel activates zone F7. Typical Uses For example, program zones F5 and F6 to activate at one time of day and deactivate at another time, on certain days of the week. You can turn a non-fire control point on and off, by using zone F5 or F6. For day/night sensitivity use, consider zones F5 and F6 as Day zones. Other uses for zone F7 include: a special day-of-year control; or an 8th day in programming zones F5 and F6. Table 8 Control Time Functions AFP-300/AFP-400 Operations PN 50260:C1 05/22/97 11 Technical Manuals line! -

16 3. Operating Modes Time Functions Operating Coding Functions Zone F8 reserved for NAC coding functions is only used by panel NAC circuits listing zone F8. You can select one of the four code types listed in Table 9: Code March Time (default) Two-Stage California Temporal Signal 120 PPM (Pulses Per Minute) Alert signal 20 PPM; General alarm signal: Steady on 10 sec. on, 5 sec. off, repeats 0.5 on, 0.5 off, 0.5 on, 0.5 off, 0.5 on, 1.5 off, repeats Presignal/Positive Sequence (PAS) Operation Table 9 Zone F8 Type Codes Notes on using coding functions: CMX modules Zone F8 does not work if listed in the CBE of CMX modules. Two-Stage When an alarm occurs, an NAC programmed for two-stage, and not activated by another zone, pulses at 20 PPM. After 5 minutes, the NAC changes to steady on unless you press <Acknowledge/Step>. Pressing < Activate> on the control panel changes the NAC pulse to steady. ICM-4/ICE-4 modules do not support Two-Stage and turn on steady. ICM-4/ICE-4 modules To enable California Code, cut D35 on the ICM-4 modules. If D35 is not cut, ICM-4/ICE-4 modules turn on steady. Zone F0 is reserved for Presignal functions. Zone F0 can be used to delay control points until an operator verifies an active control point. If including zone F0 in a CMX or NAC CBE list, zone F0 overrides all other CBE actions. Detectors and monitor modules must list zone F0 in the CBE to be included in the Presignal/PAS operation. If... And/or... Zone F0 an alarm occurs and there is no PAS inhibit type MMX activates a second alarm activates or you press the alarm activate key, goes false you select PAS and you do not press ACKNOWLEDGE within 15 seconds goes false Table 10 Presignal Operation At the first alarm, a programmable second timer starts. If a Signal Silence occurs, the timer stops. If the delay timer expires, manual activation will activate outputs mapped to zone F0. The System relay, the 4XTM Polarity Reversal Output, and the 4XTM Municipal Box Output delay if PAS is selected, but do not delay for Presignal operations 12 AFP-300/AFP-400 Operations PN 50260:C1 05/22/97 Technical Manuals line! -

17 Time Functions Special System Timers 3. Operating Modes The control panel can operate with special system timers: Silence Inhibit, Auto Silence, and Verification. Table 11 contains descriptions of how each timer works. Timer Duration If selected... Silence Inhibit seconds Starts at first alarm and restarts with each new alarm. Disables the Silence switch. Auto Silence seconds(0=no timer selected) Automatically shuts off outputs selected as silenceable after the programmed time elapses. To restart the timer, press < Activate>. Verification 0-30 seconds The control panel ignores a CPX, SDX, LPX, or IPX smoke detector for the Verification time. If another point alarm occurs during the Verification time, the control panel dumps the timer and activates the alarm. If a time-out and an alarm exist, the initiating device CBE executes all standard functions. If at timeout an alarm no longer exists in the alarm initiating devices, the control panel increments a verification counter (1-99) for the device and returns to normal operation. Waterflow Circuits Operation Table 11 Special System Timers If an alarm originates from a monitor point with a waterflow type code, the control panel disables the Silence switch. Refer to the AFP-300/AFP-400 Installation Manual for information on Waterflow Circuits. Disable/Enable Operation Disabled input points do not cause an alarm or any Control-by-Event activity. The control panel does the following: holds all disabled output points in the off-state; and handles all disabled points as troubles, but displays DISABL in the status banner. Style 6 Operation! Caution: Disabling a zone disables all input and output devices associated with the zone. The control panel will detect a trouble in an SLC wired and programmed for Style 6 or Style 7 and drive both ends of the line to maintain communication over the loop. The trouble latches and displays on the panel as a Style 6 trouble type until you press <System Reset>. Style 7 requires use of ISO-X modules. AFP-300/AFP-400 Operations PN 50260:C1 05/22/97 13 Technical Manuals line! -

18 Notes 14 AFP-300/AFP-400 Operations PN 50260:C1 05/22/97 Technical Manuals line! -

19 Overview 4. Read Status Read Status functions do not require a password. The control panel will continue to provide fire protection while in Read Status. You can enter Read Status while in Fire or Trouble mode. If a new alarm or trouble occurs during these functions, the control panel automatically exits Read Status. How to Enter Read Status Press <Enter>. The control panel displays the following screen: 1=PROGRAMMING (ESCAPE TO ABORT) 2=READ STATUS ENTRY Figure 9 Programming Entry Screen From the Programming Entry Screen, press <2>. The control panel displays the following screen: READ POINT=0 HIST=2 ALARM HIST=4 <ENTER> PRNT POINT=1 HIST=3 ALARM HIST=5 <ENTER> Figure 10 Read Status Screen Note: If attempting to read a point that is not installed, the control panel displays NOT INSTALLED. Read Status Options To do a Read Status, follow the instructions in Table 12: To... Do this... Read Point Print Points Read History Print History 1. Press 0 C 2. Press H J I or z 3. Enter the device or zone address. Press 1 C Press 2 C Press 3 C Read History Press 4 C Print History Press 5 C Table 12 Read Status Options During all Read Status operations (except print operations) the control panel starts a 2-minute timer each time you press a key. If the control panel does not detect a key press for 2 minutes, the panel leaves the current operation and returns to the previous display. Press <Esc> to delete the previous entry. Press <System Reset> to abort Read Status. AFP-300/AFP-400 Operations PN 50260:C1 05/22/97 15 Technical Manuals line! -

20 4. Read Status Read Status Options Read Status for Points and Zones Read Point options let you display point and zone status on the display, but the information is not sent to the serial ports or the history file. To read the status of points and zones, press <0> then <Enter> from the Read Status screen. The control panel displays the Read Point screen (Figure 11): ZONE=Z,AA,E MODULE=#,AAA,E DETECTORS=*,AAA,E OUTPUT CKT=&,A-A,E Figure 11 Read Point Screen To read a detector, press H then enter the detector address. To read a module, press I then enter the module address. Read Status for a Detector, Module, or Output To read an output circuit, press J then enter the output circuit address. From the Read Status screen, press 0; then press <Enter>. You can then read the status of a detector, module, or output. For example, to read the status of a detector at D101, press H, enter the address (D101), then press <Enter>. The control panel displays information about the detector as shown in Figure 12: Type Code Custom Label for the detector NORMAL SMOKE (PHOTO) DETECTOR ADDR 101 Z03 Z Z Z Z 000%AL:5 PA:0 *V D101 Default Zone Selection Sensitivity Level Pre- Sensitivity Level Address (01-99) SLC loop number D (Detector) or M (Module or Output Verification selection Multidetector selection Figure 12 Detector Read Status Sample Screen 16 AFP-300/AFP-400 Operations PN 50260:C1 05/22/97 Technical Manuals line! -

21 Read Status Options 4. Read Status Table 13 contains descriptions of the fields shown in Figure 12: Field SMOKE (PHOTO) Description Type code of the detector. DETECTOR ADDR 101 Default custom label: 101 (1=loop 1; 01=address 01). Z03 AL:5 PA:0 Default zone selection: Zone 01 (Heat detectors) Zone 02 (Ion detectors) Zone 03 (Photo detectors) Zone 04 (Laser detectors) Zone 05 (Multi detectors) You can change zones as well as add four more zones for each detector s CBE. The sensitivity level, with 9 the least sensitive level and 1 the most sensitive level. Shows the Pre- level setting a number between 0 and 9 as follows: 0 no Pre-. 1 most sensitive Pre- level. 9 least sensitive Pre- level. *V * The asterisk (*) indicates the cooperative multidetector mode: A combines the detector's alarm decision with the next address above. B combines the detector's alarm decision with the next address below. C combines the detector's alarm decision with the next address above and the next address below. V indicates Verification (V=on, *=off). Table 13 Default Read Status Values for a Detector Read Status for a Zone Address Note: Press L to read a point or zone with next highest address; or press M to read a point or zone with next lowest address. From the Read Point screen, press z, then enter the zone address (01-99) Figure 13 shows the default Read Status display for a zone: Zone status (ON or OFF) OFF SOFTWARE ZONE FLOOR 5 MAIN BLDG Z04 Zone number Figure 13 Read Status Display for a Zone Address AFP-300/AFP-400 Operations PN 50260:C1 05/22/97 17 Technical Manuals line! -

22 4. Read Status Read Status Options Read History View Event History The control panel maintains a history file of the last 800 events, each with a time and date stamp. History events include the following: All alarms, troubles and operator actions, such as: Acknowledge, Reset, Signal Silence, Activate, and Walk Test. Programming entries, along with a number (0-9) indicating the programming submenu (for example, 0=Clear). The control panel contains two event buffers: a History buffer that can store up to 800 events (all types); and an buffer that can store up to 200 alarm events. From the Read Status screen, press <2>; then, press <Enter> to display the Event History screen. Figure 14 shows a sample Event History screen: EVENT HISTORY START EVENTS IN HISTORY : 800 The number of events in the History buffer View History Figure 14 Event History Screen From the Read Status screen, press <4>; then, press <Enter> to display the Event History screen. Figure 15 shows a sample Event History screen: ALARM HISTORY START (ESCAPE TO ABORT) ALARMS IN HIST : 200 The number of events in the buffer View or Print Hidden History Figure 15 History Screen If you clear History, events remain in a shadow file known as a Hidden History file. To display or print a Hidden History file, follow the instructions in Table 14. To clear the history file, refer to the instructions in the AFP-300/AFP-400 Programming Manual. To... Read Hidden history Print Hidden history Read Hidden Normal history Print Hidden Normal history Press... 6 C 7 C 8 C 9 C Table 14 Hidden History Selections Viewing and printing Hidden History is similar to Read Point. ce you read a Hidden History, you can do the following: Press L to view the next event in sequence; or Press M to view the previous event in sequence. 18 AFP-300/AFP-400 Operations PN 50260:C1 05/22/97 Technical Manuals line! -

23 Read Status Options Presignal Delay 4. Read Status Figure 16 shows a typical format for displaying software zone F0 (Presignal Delay): OFF PRESIGNAL FUNCT PRESIGNAL DELAY DELAY=180 PAS=NO F00 Figure 16 Presignal Delay Screen DELAY=180 shows the programmed Presignal delay of 180 seconds. PAS=Yes shows that Positive Sequence (PAS) operation is selected in the program; PAS=No shows that PAS operation is not selected in the program. Releasing Zones Figure 17 shows the typical format for displaying Releasing Zones R0-R9: OFF SOFTWARE ZONE DELAY=30 ABORT=ULI RELEASE CONTROL CROSS=Y SOAK=000 R0 Figure 17 Releasing Zone Screen Note: Refer to the AFP-300/ DELAY=30 shows the programmed delay time, in seconds. AFP-400 Programming Manual for information on Releasing ABORT=ULI shows the abort function (ULI, IRI, NYC, or AHJ, if an abort switch Zones and the Soak Timer. is mapped to this zone. CROSS=Y indicates that cross zoning is used (requires two or more detectors programmed to this zone in alarm to activate the zone). SOAK specifies the Soak Timer (automatic shut off of device) value ( seconds; 0000 = no Soak Timer). Time Control Zones Figure 18 shows the typical format for displaying time control zones F5 and F6: OFF TIME FUNCTION TIME CONTROL ON=07:00 OFF=18:00 DAYS=MTWTF H FO5 The ON time for devices programmed for zone F5 The OFF time for devices programmed for zone F5 Indicates zone F5 Holiday schedule defined by zone F7 Figure 18 Time Control Screen The Time Control screen provides the following information: ON=7:00 OFF=18:00 shows the programmed times in 24-hour (military) format when zone F5 automatically turns on and off each day. DAYS= MTWTF H shows the programmed days-of-week when the / times are effective. H is a holiday schedule defined by the program for zone F7. You can also select zone F5 or F6 for detector day/night sensitivity. For example, you can do the following: 1. List zone F5 in the CBE of an initiating device, such as a smoke detector. 2. Set the time for F5 to 07:00 and the time for F5 to 19: When zone F5 is active at 07:00, the control panel forces the detector sensitivity of any initiating device listed for zone F5 to the least sensitive setting. When zone F5 goes off at 19:00, the detector sensitivity returns to it s original setting. AFP-300/AFP-400 Operations PN 50260:C1 05/22/97 19 Technical Manuals line! -

24 4. Read Status Read Status Options Holiday Zones Figure 19 shows the typical format for displaying software zone F7 (Holiday zone): OFF HOLIDAY FUNCT 01/01 03/38 05/26 06/03 07/04 09/04 11/23 11/24 12/25 A Day/Month program selection for Holiday days of the month. Figure 19 Holiday Zone Screen NAC Coding Zone Figure 20 shows the typical format for displaying NAC coding using software zone F8: OFF CODING FUNCTION CODE TYPE MARCH TIME F08 Indicates the NAC coding selection Refer to Operating Coding Functions on page 12. Indicates NAC coding zone F8 Pre- Zone Figure 20 NAC Coding Zone Screen The NAC coding selection indicates the type of coding applied to each of the four panel Notification Appliance Circuits that list zone F8 in their CBE. Zone F8 does not affect addressable control modules. NAC coding selections include the following: March Time (default) 120 PPM (Pulses Per Minute) Alert signal 20 PPM; General alarm signal: Steady on California 10 sec. on, 5 sec. off, repeats Temporal 0.5 on, 0.5 off, 0.5 on, 0.5 off, 0.5 on, 1.5 off, repeats Figure 21 shows the typical format for displaying software zone F9 (Pre-): OFF PRE-ALARM FUNCT ALERT F09 Note: Refer to the AFP-300/ AFP-400 Programming Manual for more information on Pre- settings. Figure 21 Pre- Zone Screen You can list zone F9 in the CBE of any control point. The Pre- zone turns on if any detector reaches a Pre- threshold. Zone F9 indicates the beginning of an alarm, or when the detector needs maintenance. 20 AFP-300/AFP-400 Operations PN 50260:C1 05/22/97 Technical Manuals line! -

25 Read Status Options System Parameters To read System Parameters, follow these steps. 4. Read Status 1. Select Read Point from the Read Status screen to display the Read Point screen (Figure 11): 2. Press <Z>, <S0>, <Enter> to display the System Parameters screen, which typically displays as shown in Figure 22: SIL INH=060 AUTO=600 VERIFY=30 USA TIME TERM SUPERV=NO LocT BLINK=Y ST=4 ACS=N Figure 22 System Parameters Screen 0 Table 15 contains descriptions of the items shown on System Parameter Screen (Figure 22): Parameter Description Set to... SIL INH=060 AUTO=600 Silence Inhibit timer in seconds. Required in Canada and some areas of the USA. Automatic Silence timer in seconds. 0 no timer; or the timer duration in seconds. 0 no timer; or the timer duration in seconds. VERIFY=30 Verification timer 0 no timer; or the timer duration in seconds. USA TIME Time/date display format USA TIME or EUR TIME TERM_SUPERV=YES Terminal supervision YES To supervise the wiring of a terminal mode LCD-80. NO No Terminal mode and no LCD-80 supervision. LocT BLINK=Y ST=4 ACS=N e of three operating modes of a PC or terminal connected to the control panel (through TB2 PC/ Terminal). For a complete list of functions, refer to the AFP-300/AFP-400 Installation Manual. Blink LEDs on intelligent devices during polling (for certain applications). NFPA wiring style operation for the SLC loop Use ACS Selection Groups (refer to the AFP-300/ AFP-400 Installation Manual for details). LocT terminal connected to control panel and located in the same room as the control panel. LocM terminal connected to control panel but requires password for operation. RemT terminal connected through a modem for Read Status operations only. Y blink LED; or N do not blink LED. 4 Style 4 SLC loop; or 6 both Style 6 and Style 7 SLC loop. N No annunciator selected; or Y Select and display ACS Selection Groups. Table 15 System Parameters AFP-300/AFP-400 Operations PN 50260:C1 05/22/97 21 Technical Manuals line! -

26 4. Read Status Read Status Options Annunciator Display Selections Press <Z>, <S1>, <Enter> to display Annunciator Selection 1 Screen which typically displays as shown in Figure 23: A=Address ANNUN SELECTION1: A1=* A2=* A3=* A4=* A5=* A6=* A7=* A8=* A9=* A10=* UDACT=N Note: Refer to Appendix A, Annunciators in the AFP-300/ AFP-400 Installation Manual for detailed instructions on using an AMG-1 in ACS mode. For programming instructions, refer to the AFP-300/AFP-400 Programming Manual. Figure 23 Annunciator Selection 1 Screen If UDACT=N, the control panel displays the Annunciator Selection 2 Screen, addresses A11 A19, as shown in Figure 24: ANNUN SELECTION2: A11=* A12=* A13=* A14=* A15=* A16=* A17=* A18=* A19=* Figure 24 Annunciator Selection 2 Screen Use the Annunciator Selection screen to select information that will display on the ACS annunciators. Table 16 contains the ACS display selections. ACS Selection Group Annunciator Display 1 CPU status and zones Zones 57 to 99, NAC circuits 1-4 and 16 special zones 3 Intelligent modules 101 to Intelligent modules 201 to 264 (AFP-400 only) 5 Intelligent modules 165 to 196 and 265 to 296 (AFP-400 only) 6 Detectors 101 to 164 on SLC 1 7 Detectors 201 to 264 on SLC 2 (AFP-400 only) 8 Detectors 165 to 196 and 265 to 296 (AFP-400 only) 9 NAC/panel output circuit modules (64 points) * or 0 Annunciator not installed at address Example of Annunciator Display Selections Table 16 ACS Selection Groups Figure 25 shows an example of ACS selections in Annunciator Selection Screen 1: ANNUN SELECTION1: A1=6 A2=3 A3=9 A4=* A5=* A6=* A7=* A8=* A9=* A10=* UDACT=Y Figure 25 Annunciator Selection Screen 1 Example Figure 25 shows annunciator selections for addresses A1-A3 (addresses A4-A10 are not selected). Annunciators set to Address 1 display the status of detectors 1-64 on SLC 1 (ACS Selection Group 6); Annunciators set to Address 2 display the status intelligent modules (ACS Selection Group 3); and Annunciators set to Address 3 display the status of the panel modules (ACS Selection Group 9). 22 AFP-300/AFP-400 Operations PN 50260:C1 05/22/97 Technical Manuals line! -