signal extraction pulse oximeter OPERATOR S MANUAL

Transcription

1 signal extraction pulse oximeter OPERATOR S MANUAL

2 Signal Extraction Pulse Oximeter OPERATOR S MANUAL

3 The Radical-7 Operating Instructions provide the necessary information for proper of all models of the Radical-7 pulse oximetry system. There may be information provided in this manual that is not relevant for your system. General knowledge of pulse oximetry and an understanding of the features and functions of the Radical-7 Pulse Oximeter are a prerequisite for its proper use. Do not operate the Radical-7 Pulse Oximeter without completely reading and understanding the instructions in this manual. NOTICE Purchase or possession of this device does not carry any express or implied license to use this device with replacement parts which would, alone or in combination with this device, fall within the scope of one of the patents relating to this device. CAUTION: FEDERAL LAW (U.S.) RESTRICTS THIS DEVICE TO SALE BY OR ON THE ORDER OF A PHYSICIAN. Masimo Corporation 40 Parker Irvine, CA USA Tel.: Fax.: EU Authorized Representative for Masimo Corporation: EC REP MDSS Burckhardtstrasse Hannover, Germany Tel.: Fax.: MEDICAL ELECTRICAL EQUIPMENT WITH RESPECT TO ELECTRIC SHOCK, FIRE AND MECHANICAL HAZARDS ONLY IN ACCORDANCE WITH UL /CAN/CSA C22.2 No Covered by one or more of the following U.S. Patents: RE38,492, RE38,476, 6,850,787, 6,826,419, 6,816,741, 6,699,194, 6,684,090, 6,658,276, 6,654,624, 6,650,917, 6,643,530, 6,606,511, 6,584,336, 6,501,975, 6,463,311, 6,430,525, 6,360,114, 6,263,222, 6,236,872, 6,229,856, 6,206,830, 6,157,850, 6,067,462, 6,011,986, 6,002,952, 5,919,134, 5,823,950, 5,769,785, 5,758,644, 5,685,299, 5,632,272, 5,490,505, 5,482,036, international equivalents, or one or more of the patents referenced at Products containing Satshare feature are also covered by U.S. Patent 6,770,028. Other patents pending Masimo Corporation. Masimo, Discrete Saturation Transform, DST, Satshare, SET, LNOP, LNCS and LNOPv are federally registered trademarks of Masimo Corporation. Radical-7, Rainbow, RadNet, RadicalScreen, Signal IQ, FastSat, FastStart and APOD are trademarks of Masimo Corporation. Radical-7 Signal Extraction Pulse Oximeter Operator s Manual i

4 SAFETY INFORMATION,WARNINGS, CAUTIONS AND NOTES The Radical-7 Signal Extraction Pulse Oximeter s is designed to minimize the possibility of hazards from errors in the software program by following sound engineering design processes, Risk Analysis and Software Validation. Explosion hazard. Do not use the Pulse Oximeter in the presence of flammable anesthetics or other flammable substance in combination with air, oxygen-enriched environments, or nitrous oxide. The Pulse Oximeter is NOT intended for use as an apnea monitor. A Pulse Oximeter should be considered an early warning device. As a trend towards patient hypoxemia is indicated, blood samples should be analyzed by laboratory instruments to completely understand the patient s condition. The Pulse Oximeter is to be operated by qualified personnel only. This manual, accessory directions for use, all precautionary information, and specifications should be read and understood before use. Electric shock hazard. Do not open the pulse oximeter cover except to replace the battery of the Handheld unit. Only a qualified operator may perform maintenance procedures specifically described in this manual. Refer servicing to Masimo for repair of this equipment. As with all medical equipment, carefully route patient cabling to reduce the possibility of patient entanglement or strangulation. Do not place the pulse oximeter or accessories in any position that might cause it to fall on the patient. Do not lift the pulse oximeter by the power cord or any other cable. Interfering Substances: Carboxyhemoglobin and Methemoglobin may erroneously increase readings. The level of increase is approximately equal to the amount of carboxyhemoglobin present. Dyes, or any substance containing dyes, that change usual blood pigmentation may cause erroneous readings. Elevated levels of Methemoglobin (MetHb) will lead to inaccurate SpO 2 measurements. Severe anemia may cause erroneous SpO 2 readings. Do not use the pulse oximeter or oximetry sensors during magnetic resonance imaging (MRI) scanning. Induced current could potentially cause burns. The pulse oximeter may affect the MRI image, and the MRI unit may affect the accuracy of the oximetry measurements. If using pulse oximetry during full body irradiation, keep the sensor out of the irradiation field. If the sensor is exposed to the irradiation, the reading might be inaccurate or the unit might read zero for the duration of the active irradiation period. For home use, ensure that the pulse oximeter s alarm can be heard from other rooms in the house especially when noisy appliances such as vacuum cleaners, dishwashers, clothes dryers, televisions, or radios are operating. Always remove the sensor from the patient and completely disconnect the patient from the pulse oximeter before bathing the patient. Do not place the pulse oximeter where the controls can be changed by the patient. Do not place the pulse oximeter face against a surface. This will cause the alarm to be muffled. Do not place the pulse oximeter on electrical equipment that may affect the pulse oximeter, preventing it from working properly. Do not expose the pulse oximeter to excessive moisture such as direct exposure to rain. Excessive moisture can cause the pulse oximeter to perform inaccurately or fail. Do not place containers containing liquids on or near the pulse oximeter. Liquids spilled on the pulse oximeter may cause it to perform inaccurately or fail. SAFETY INFORMATION,WARNINGS, CAUTIONS AND NOTES (CONTINUED) Failure of Operation - If the pulse oximeter fails any part of the setup procedures or leakage tests, remove the pulse oximeter from until qualified service personnel have corrected the situation. Patient Safety - If a sensor or cable is damaged in any way, discontinue use immediately. The Pulse Oximeter Module can be used during defibrillation, but the readings may be inaccurate for up to 20 seconds. This equipment has been tested and found to comply with the limits for medical devices to the EN : 2002, Medical Device Directive 93/42/EEC. These limits are designed to provide reasonable protection against harmful interference in a typical medical installation.this equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to other devices in the vicinity. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to other devices, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving device. Increase the separation between the equipment. Connect the equipment into an outlet on a circuit different from that to which the other device(s) are connected. Consult the manufacturer for help. ii Radical-7 Signal Extraction Pulse Oximeter Operator s Manual Radical-7 Signal Extraction Pulse Oximeter Operator s Manual iii

5 table of contents table of contents SECTION 1 - OVERVIEW About this Manual Product description Features and benefits Indications for use Pulse oximetry General Description Principle of Operation Functional vs. fractional saturation Measured vs. Calculated Saturation Masimo set signal extraction technology SECTION 2 - SYSTEM DESCRIPTION Introduction Radical-7 handheld Handheld Front Panel Handheld back Panel Radical-7 standalone Standalone Front Panel Standalone Back Panel Symbols Radical-7 monitor interface SECTION 3 - SETUP Introduction Unpacking and inspection Preparation for monitoring Radical-7 power requirements Initial battery charging Initial installation Monitor setup Factory Default Settings Custom (user) Defined Settings Adult/neo (hospital defined) settings Satshare setup Philips VueLink setup Spacelabs universal flexport setup RadNet setup SECTION 4 - OPERATION Introduction Basic General Setup and Use Successful SpO2 monitoring Numeric Display - SpO Masimo Sensors Numeric Display - Pulse Rate Signal IQ Low Perfusion Actions To Be Taken Touch key control button and icons Traditional user interface First Page Second page Simplified user interface First page Second Page Navigating the main menu Main menu selection Menu categories Editing a parameter Menu tree Alarms Display General Clock Output About Config Service Trend display Navigating the trend display First page Second page Third page Trend setup Backlight/contrast Satshare Home mode Password SECTION 5 - ALARMS/MESSAGES Introduction Alarm identification Alarm Alarm messages System messages D Alarm System option Purpose D Alarm System overview Desat Index Alarm Perfusion Index (PI) Delta alarm Desat Index Alarm User Interaction to Implement Desat Index Alarm Perfusion Index (PI) Delta Alarm User Interaction to Implement PI Delta Alarm SECTION 6 - TROUBLESHOOTING Troubleshooting SECTION 7 - SPECIFICATIONS Radical-7 specifications iv Radical-7 Signal Extraction Pulse Oximeter Operator s Manual Radical-7 Signal Extraction Pulse Oximeter Operator s Manual v

6 table of contents overview 1 Performance Electrical Environmental Physical characteristics Serial interface specifications Serial Interface Setup Serial Printer Setup Analog output / nurse call specifications Analog Output Calibration Nurse Call SECTION 8 - SENSORS & PATIENT CABLES Introduction Selecting a sensor Sensor Application Site Masimo SpO2 sensors Red Reusable Sensors LNOP Reusable Sensors LNOP Adhesive Sensors LNOP Specialty Sensors LNCSTM Reusable Sensors LNCSTM Adhesive Sensors LNOPvTM Adhesive Sensors Sensor Accuracy Cleaning And Reuse Of Masimo reusable Sensors and cables Reattachment of Single Use adhesive Sensors SECTION 9 - SERVICE AND MAINTENANCE Introduction Cleaning Battery and maintenance Replacing the Batteries Replacing the Fuses Performance verification Service and repair Repair Policy Return Procedure Warranty Exclusions End-user license agreement SECTION 10 - ACCESSORIES Accessories About this Manual This manual explains how to set up and use the Masimo Rainbow SET Radical-7 Pulse Oximeter, herein known as the Radical-7. Important safety information relating to general use of the Radical-7 appears before this introduction. Other important safety information is located throughout the manual where appropriate. Read the entire safety information section before you operate the monitor. In addition to the safety section, this manual includes the following sections: SECTION 1 OVERVIEW gives a general description of pulse oximetry. SECTION 2 SECTION 3 SECTION 4 SECTION 5 SECTION 6 SYSTEM DESCRIPTION describes the Radical-7 Pulse Oximeter system and its functions and features. SETUP describes how to setup the Radical-7 Pulse Oximeter for use. OPERATION describes the of the Radical-7 Pulse Oximetry system. ALARMS AND MESSAGES describes the alarm system messages. TROUBLESHOOTING describes troubleshooting information. SECTION 7 SPECIFICATIONS gives the detailed specifications of the Radical-7 Pulse Oximeter. SECTION 8 SECTION 9 SECTION 10 SENSORS AND PATIENT CABLES outlines how to use and care for Masimo SET sensors, and Masimo SET patient cables. SERVICE AND MAINTENANCE describes how to maintain, service and obtain repair for the Radical-7 Pulse Oximeter. ACCESSORIES lists the available Radical-7 accessories. vi Radical-7 Signal Extraction Pulse Oximeter Operator s Manual Radical-7 Signal Extraction Pulse Oximeter Operator s Manual 1-1

7 1 overview overview 1 Warnings, cautions and notes Please read and follow any warnings, cautions and notes presented throughout this manual. An explanation of these labels are as follows: A WARNING is provided when actions may result in a serious outcome (i.e., injury, serious adverse affect, death) to the patient or user. Look for text in a gray shaded box. Sample of Warning: Product description The Radical-7 Pulse Oximeter is a noninvasive, arterial oxygen saturation and pulse rate monitor. The Radical-7 can be used as either a Handheld or a Standalone monitor. The Radical-7 features a backlit Liquid Crystal Display (LCD) that continuously displays numeric values for SpO 2, pulse rate, plethysmographic waveform and Signal Identification and Quality Indicator (Signal IQ TM ). The Radical-7 can be used to interface with a multiparameter patient monitor to provide Masimo SET pulse oximetry information to that monitor for display. WARNING: THIS IS A SAMPLE OF A WARNING STATEMENT. A CAUTION is given when any special care is to be exercised by the patient or user to avoid injury to the patient, damage to this device or damage to other property. Sample of Caution: CAUTION: THIS IS A SAMPLE OF A CAUTION STATEMENT. A NOTE is provided when extra general information is applicable. Sample of Note: NOTE: This is a sample of a Note. FEATURES AND BENEFITS Clinically proven Masimo SET technology performance Applicable for use on neonate, pediatric, infant and adult patients Proven for accurate monitoring in motion and low perfusion environments Universal application: Handheld, Standalone and Patient Monitor Interface Automatic upright display with RadicalScreen TM Signal IQ TM for signal identification and quality indication Analog output and nurse call SpO 2, pulse rate, alarm, perfusion index, trend and pleth waveform (non-normalized) displays Lightweight design Internal batteries for transport: Standalone -10 hours (optional) Handheld - 4 hours Serial output to printers and PCs RadNet TM capability (only when used with a RadNet TM Ready Docking Station) INDICATIONS FOR USE The Radical-7 Pulse Oximeter and accessories are indicated for the continuous, noninvasive monitoring of functional oxygen saturation of arterial hemoglobin (SpO 2 ) and pulse rate (measured by an SpO 2 sensor). The Radical-7 Pulse Oximeter and accessories are indicated for use with adult, pediatric, infant and neonatal patients during both motion and no motion conditions, and for patients who are well or poorly perfused in hospitals, hospital-type facilities, mobile and home environments. In addition, the Radical-7 Pulse Oximeter is indicated to provide continuous noninvasive monitoring data to validated multiparameter patient monitors* for display on those monitors. *Contact Masimo for the latest list of SatShare validated multiparameter monitors. 1-2 Radical-7 Signal Extraction Pulse Oximeter Operator s Manual Radical-7 Signal Extraction Pulse Oximeter Operator s Manual 1-3

8 1 overview overview 1 Pulse oximetry GENERAL DESCRIPTION Pulse oximetry is a continuous and non-invasive method of measuring the level of arterial oxygen saturation in blood. The measurement is taken by placing a sensor on a patient, usually on the fingertip for adults and the hand or foot for neonates. The sensor is connected to the pulse oximetry instrument with a patient cable. The sensor collects signal data from the patient and sends it to the instrument. The instrument displays the calculated data in three ways: 1. As a percent value for arterial oxygen saturation (SpO 2 ) 2. As a pulse rate (PR) 3. As a plethysmographic waveform The following figure shows the general monitoring setup. FUNCTIONAL VS. FRACTIONAL SATURATION The Radical-7 is calibrated to measure and display functional saturation: the amount of oxygenated hemoglobin expressed as a percentage of the hemoglobin that can transport oxygen. The Radical-7 does not measure fractional saturation: oxygenated hemoglobin expressed as a percentage of all measured hemoglobin, including measured dysfunctional hemoglobin such as carboxyhemoglobin or methemoglobin. To convert fractional saturation to functional saturation, the fractional saturation measurements must be converted according to: Instrument 2. Patient Cable 3. Sensor PRINCIPLE OF OPERATION Pulse oximetry is governed by the following principles: 1. Oxyhemoglobin (oxygenated blood) and deoxyhemoglobin (non-oxygenated blood) differ in their absorption of red and infrared light (spectrophotometry). 2. The amount of arterial blood in tissue changes with your pulse (photoplethysography). Therefore, the amount of light absorbed by the varying quantities of arterial blood changes as well. The Radical-7 Pulse Oximeter uses a two-wavelength pulsatile system to distinguish between oxygenated and deoxygenated blood. Signal data is obtained by passing red (rd)(660 nm wavelength) and infrared (ir)(905 nm wavelength) light through a vascular bed (for example a fingertip, a hand, a foot) and measuring changes in light absorption during the pulsatile cycle. This information may be useful to clinicians. The radiant power of the light is rated at 0.79mW (max.). See figure below. The Radical-7 utilizes a sensor with red and infrared light-emitting diodes (LEDs) that pass light through the site to a photodiode (photodetector). The photodetector receives the light, converts it into an electronic signal and sends it to the Radical-7 for calculation. Functional saturation = Fractional saturation (% carboxyhemoglobin + % methemoglobin) x 100 MEASURED VS. CALCULATED SATURATION Oxygen saturation measurements obtained from a pulse oximeter are commonly compared to saturations calculated from the partial pressure of oxygen (PO 2 ) obtained from an arterial blood gas sample. When comparing the two measurements, caution should be used when interpreting the values, as the calculated value obtained from the blood gas sample may differ from the SpO 2 measurement of the pulse oximeter. Different results are usually obtained from the blood gas sample if the calculated saturation is not appropriately corrected for the effects of variables that shift the relationship between PO 2 and saturation, such as: ph, temperature, the partial pressure of carbon dioxide (PCO 2 ), 2,3-DPG, and fetal hemoglobin. Also, as blood gas samples are usually taken over a period of 20 seconds (the time it takes to draw blood) a meaningful comparison can only be achieved if the core oxygen saturation of the patient is stable and not changing over the period of time that the blood gas sample is taken. MASIMO SET SIGNAL EXTRACTION TECHNOLOGY Masimo Signal Extraction Technology s signal processing differs from conventional pulse oximeters. Conventional pulse oximeters assume that arterial blood is the only blood moving (pulsating) in the measurement site. During patient motion, however, the nonarterial blood also moves, which causes conventional pulse oximeters to read low values, because they cannot distinguish between the arterial and venous blood movement (sometimes referred to as noise). Masimo SET pulse oximetry utilizes parallel engines and adaptive digital filtering. Adaptive filters are powerful because they are able to adapt to the varying physiologic signals and/or noise and separate them by looking at the whole signal and breaking it down to its fundamental components. The Masimo SET signal processing algorithm, Discrete Saturation Transform (DST), reliably identifies the noise, isolates it and, using adaptive filters, cancels it. It then reports the true arterial oxygen saturation for display on the monitor. LED's Recessed Photo Detector Once the Radical-7 receives the signal from the sensor, it utilizes Masimo Rainbow SET signal extraction technology for calculation of the patient s functional oxygen saturation and pulse rate. 1-4 Radical-7 Signal Extraction Pulse Oximeter Operator s Manual Radical-7 Signal Extraction Pulse Oximeter Operator s Manual 1-5

9 90 1 overview system description 2 Masimo SET Parallel Engines R/IR Digitized, Filtered & Normalized R/IR (Conventional Pulse Oximetry) Adaptive Filter with DST TM SST TM Proprietary Algorithm 4 Proprietary Algorithm 5 MEAS CONF MEAS CONF MEAS CONF MEAS CONF MEAS CONF Confidence Based Arbitrator Post Processor Saturation Introduction The Radical-7 provides the functionality of three pulse oximeters in one: The Radical-7 is a fully featured Handheld pulse oximeter The Radical-7 is a fully featured standalone pulse oximeter The Radical-7 interfaces to the SpO 2 input module of multiparameter patient monitors* to upgrade conventional pulse oximetry technology to Masimo SET technology. 4 The Handheld portion of the Radical-7 contains the majority of the pulse oximeter features. All pulse oximetry measurement information, as well as device status data is displayed on the Handheld LCD screen. All user input is handled through the control buttons on the front panel. The sensor cable connector is located on the Radical-7 Handheld oximeter. The Handheld oximeter snaps into the Radical-7 Docking Station to provide a fully featured standalone pulse oximeter. The Docking Station connects to AC power for standalone or charging of the Handheld. An optional Docking Station battery is available.the standalone Radical-7 features nurse call, analog output and interfaces to serial printers. Masimo SET DST CAUTIONS: Utilizing a SatShare TM cable, the standalone Radical-7 also interfaces with the SpO 2 input of a validated multiparameter patient monitor*, instantly upgrading the conventional pulse oximetry to Masimo SET pulse oximetry. The SatShare cable attaches to the back of the Radical-7 Docking Station, and SatShare cables are available to interface with most multiparameter patient monitors*. THE WAVEFORM DISPLAYED ON THE MULTIPARAMETER PATIENT MONITOR IS A SIMULATED SIGNAL (NON-NORMALIZED). REFER TO THE RADICAL-7 DISPLAY FOR PATIENT WAVEFORM. IF DISPLAYING THE SIMULATED WAVEFORM IS NOT DESIRABLE, IT IS RECOMMENDED TO TURN OFF THE PLETH WAVEFORM DISPLAY ON THE MULTIPARAMETER MONITOR ONLY USE A SATSHARE CABLE THAT HAS A FERRITE BEAD INSTALLED. Refer to Section 3, SatShare Setup and Section 4, SatShare Operation for additional details. *Contact Masimo for the latest list of SatShare validated multiparameter monitors. 1-6 Radical-7 Signal Extraction Pulse Oximeter Operator s Manual Radical-7 Signal Extraction Pulse Oximeter Operator s Manual 2-1

10 2 system description system description 2 Radical-7 handheld The Handheld Radical-7 provides most of the functionality of the pulse oximeter. All user input and displays are controlled by this part of the Radical-7 system. The sensor cable connects into the swivel connector on the Handheld unit. The Handheld is battery powered and can be used either as a transport monitor or as a Handheld Pulse Oximeter for spot checks. HANDHELD FRONT PANEL The following figure and corresponding text outline all the features of the Handheld Radical-7: Pleth + Signal IQ View Numbers View 4 Masimo SET Masimo SET FastSat %SpO BPM No Sensor HPO1 160 %SpO :10:23pm 03/27/ BPM 11:42:46 03/27/ Masimo SET HANDHELD RELEASE BUTTON SpO 2 MEASUREMENT DISPLAY MASIMO SET 4 FastSat FASTSAT Max APOD SATURATION ALARM LIMITS DISPLAY ALARM STATUS INDICATOR SYSTEM MESSAGE AREA SENSITIVITY BATTERY STATUS INDICATORS TOUCH KEY CONTROL BUTTONS 11 SPEAKER PATIENT CABLE CONNECTOR TOUCH KEY ICONS Press down the Handheld Release Button and pull the Handheld device off the Docking Station. The functional arterial hemoglobin oxygen saturation is displayed in units of percentage SpO 2. The upper and lower SpO 2 alarm limits are also displayed next to the SpO 2 measurement. When a sensor is not connected to a patient and during pulse search, the display will show dashed lines. When the measured value is outside of the alarm limits, the SpO 2 Measurement Display flashes and an alarm will sound. The oxygen saturation is calculated and the display is updated at a frequency of once per second. The Masimo SET symbol is shown on the Radical-7 display when SET processing is active. Note: Patient information, not Masimo SET will be displayed when using a RadNet compatible unit connected to a RadNet central station The FastSat symbol is shown on the Radical-7 display whenever the Radical-7 is set to operate in the FastSat mode. The Saturation Alarm Limits Display shows the upper and lower saturation alarm limits. When an alarm limit is reached or exceeded, the SpO 2 value and the violated limit flashes. The alarm status indicator (a bell) can be shown with or without a slash. It flashes when an alarm condition is present. When the alarm is silenced using the Alarm Silence Button, an alarm status indicator with a slash and a timer is shown to indicate that the alarm is temporarily silenced. When the alarm is silenced through All Mute menu selection, which is permanent until power is cycled or deselected using menu, an alarm status indicator with a slash is shown to indicate that alarm has been silenced. The system messages generated by the instrument are displayed in the System Message Area. See Section 5, System messages. The Max or APOD sensitivity icon is shown on the Radical-7 display to indicate if the Radical-7 is set to operate in Normal sensitivity, Maximum sensitivity or Adaptive Probe Off Detection mode The Battery Status Indicators show the capacity of the Radical-7 Handheld and optional Docking Station batteries. The indicator flashes when less than 15 minutes of battery life is left and the battery needs to be recharged. The Docking Station Battery Status indicator is not shown when the optional Docking Station battery is not present. Press a Touch Key Control Button to select the corresponding touch key icon. See Section 4, Touch Key Control Buttons and Icons for more details. The speaker indicates audio alarms. Care should be taken not to cover the speaker and muffle the audible alarm volume. Connect the patient cable to the Handheld Radical-7 by plugging the cable into the Patient Cable Connector. Use only Masimo compatible sensors and cables with this oximeter. See Section 8, Sensors and Patient Cables for more details. The Touch Key Icons indicate the software menu items that can be selected through the Touch Key Control Buttons. Pressing a Touch Key Control Button next to an icon selects the option. 2-2 Radical-7 Signal Extraction Pulse Oximeter Operator s Manual Radical-7 Signal Extraction Pulse Oximeter Operator s Manual 2-3

11 of 2 system description system description 2 14 SIGNAL IQ The Signal IQ shows the acquired signal quality and the timing of the pulse. A tall vertical line indicates a high quality signal, while a small vertical line indicates a low quality signal. The Signal IQ may also be shown as a single, pulsating bar. HANDHELD BACK PANEL The Handheld back panel features the interconnection to the Docking Station, an accessory mount for the pole clamp accessory and access to the Handheld battery pack. 15 PULSE WAVEFORM DISPLAY 16 TIME AND DATE INDICATOR BACKLIGHT/ CONTRAST BUTTON ALARM SILENCE BUTTON 19 OUTPUT MODE INDICATOR PI POWER/STAND BY BUTTON PERFUSION INDEX PULSE RATE ALARM LIMITS DISPLAY PULSE RATE The Pulse Waveform Display shows the acquired plethysmograph waveform. The pleth waveform is scaled with signal strength. Signal strength is defined as the relation of arterial pulsatile signal to the non-pulsatile signal component. The Time and Date Indicator displays the current time and date. The time is displayed in 12 or 24 hour format. The date is displayed in dd/mm/yy or mm/dd/yy format. Select the date and time display formats in the Clock menu. Press the Backlight Button to change the illumination level of the backlight. With the AC line power connected, four levels of illumination are available (in addition to the no illumination level). In the Handheld mode, three levels of illumination are available (again in addition to the no illumination level). Use the lowest illumination for most efficient battery usage. The backlight Button is also used to change the contrast of the LCD display. Press and hold the Backlight Button for longer than six seconds to change the contrast. Release the Backlight Button at the desired contrast setting. Press the Alarm Silence Button to temporarily silence patient and low battery alarms. Press the Alarm Silence Button when the SENSOR OFF or NO SENSOR messages are flashing (i.e. the sensor is removed from the patient) to acknowledge the end of monitoring. In these states, all further alarms are suspended until the pulse oximeter starts measuring SpO 2 and pulse rate again. Note: System failure alarms can be silenced by pressing the Power/Standby or Alarm Silence Button. If the Power/Standby Button does not silence the system fault alarm, press the Alarm Silence Button. The Output Mode Indicator displays the output mode selected by the user. The Output Mode Indicator also displays the type of SatShare TM cable. The Output Mode indicator is only displayed when the Radical-7 device actively outputs data other than ASCII text, or interfaces with a monitor through the SatShare cable. Press the Power/Standby Button to turn the instrument on. Press, hold the button for more than 2 seconds and then release the button to turn the instrument off. The Perfusion Index indicates numerically the percentage of pulsatile signal to non-pulsatile signal (pulse strength) The Pulse Rate Alarm Limits Display shows the upper and lower pulse rate alarm limits. When an alarm limit is reached or exceeded, the pulse rate value and the violated limit flashes. The Pulse Rate Measurement Display shows the patient s pulse rate in beats per minute.the upper and lower pulse rate alarm limits are also displayed next to the pulse rate measurement. The pulse rate is calculated and the display is updated at a frequency of once per second DOCKING STATION CONNECTOR POLE CLAMP ACCESSORY HOLDER 3 BATTERY PACK MEDICAL ELECTRICAL EQUIPMENT UL /CAN/CSA C22.2 No FK Covered by one or more of the following U.S. Patents: RE38,492, RE38,476, 6,850,787, 6,826,419, 6,816,741, 6,699,194, 6,684,090, 6,658,276, 6,654,624, 6,650,917, 6,643,530, 6,606,511, 6,584,336, 6,501,975, 6,463,311, 6,430,525, 6,360,114, 6,263,222, 6,236,872, 6,229,856, 6,206,830, 6,157,850, 6,067,462, 6,011,986, 6,002,952, 5,919,134, 5,823,950, 5,769,785, 5,758,644, 5,685,299, 5,632,272, 5,490,505, 5,482,036, international equivalents, or one or more the patents referenced at Products containing Satshare feature are also covered by U.S. Patent 6,770,028. Other patents pending. The Radical-7 Handheld interfaces with the Docking Station through this connector. The optional Pole Clamp accessory attaches to this holder. See the Directions for Use of the Pole Clamp accessories for attachment instructions. The Radical-7 Handheld is powered by a NiMH battery located in this compartment. For battery care and replacement please see Section 9, Replacing the Batteries /2269M Radical-7 Signal Extraction Pulse Oximeter Operator s Manual Radical-7 Signal Extraction Pulse Oximeter Operator s Manual 2-5

12 2 system description system description 2 Radical-7 standalone When the Radical-7 Handheld is placed into the Docking Station, the Radical-7 becomes a full-featured standalone device.the Radical-7 Standalone acts as a battery charger for the Handheld device and has AC power connection capabilities. The Standalone can also interface to serial devices, nurse call or analog output devices, and multiparameter patient monitors through a SatShare cable. There are several models of Docking Stations available. The following table outline which features are available for each model of Docking Station. STANDALONE FRONT PANEL The following figure and corresponding text review the features of the Radical-7 Standalone device Masimo SET FastSat %SpO Check Sensor 50 DOCKING STATION FEATURES RDS-1 RDS-1B RDS-2 RDS-3 RDS-3B RDS-4 4 BPM 11:42:46 03/27/03 5 AC Power Input SatShare Interface Serial RS-232 Interface Nurse Call/Analog Output Interface 10-hour Extended Battery Automatic Display Rotation Support (Gravity Detector) Docking Station Battery Charging Indicator Handheld Battery Charging Indicator Red Alarm Indicator DOCKING STATION BATTERY CHARGING INDICATOR HANDHELD BATTERY CHARGING INDICATOR VISUAL ALARM INDICATOR AC POWER INDICATOR DOCKING INDICATOR The Docking Station Battery Charging Indicator is illuminated when the Docking Station battery is charging. The indicator blinks just prior to charging. The charging indicator does not illuminate when the battery is fully charged or when the battery is not present. The Handheld Battery Charging Indicator is illuminated when the Handheld battery is charging. The indicator blinks just prior to charging. The Charging Indicator does not illuminate when the battery is fully charged or when the battery is not present. The Visual Alarm Indicator is illuminated when an alarm condition is active and the Alarm Status Indicator is shown. The AC Power Indicator is illuminated when the Radical-7 Docking Station is plugged into AC line power. The Docking Indicator is illuminated when the Handheld unit is turned on and is properly interfaced to a Docking Station. AC Power Indicator Docking Indicator NOTE: When the Radical-7 Standalone is turned on, all indicator LEDs initially turn on and off at start up. Handheld Battery Deep Discharge Support Docking Station Battery Deep Discharge Support The RDS-1 and RDS-3 are optionally available with RadNet capability. (Refer to Section 3 RadNet Setup for details). 2-6 Radical-7 Signal Extraction Pulse Oximeter Operator s Manual Radical-7 Signal Extraction Pulse Oximeter Operator s Manual 2-7

13 MEDICAL ELECTRICAL EQUIPMENT UL /CAN/CSA C22.2 No FK Manufactured by: Masimo Corporation Irvine, CA USA Made in USA Covered by one or more of the following U.S. Patents: RE38,492, RE38,476, 6,850,787, 6,826,419, 6,816,741, 6,699,194, 6,684,090, 6,658,276, 6,654,624, 6,650,917, 6,643,530, 6,606,511, 6,584,336, 6,501,975, 6,463,311, 6,430,525, 6,360,114, 6,263,222, 6,236,872, 6,229,856, 6,206,830, 6,157,850, 6,067,462, 6,011,986, 6,002,952, 5,919,134, 5,823,950, 5,769,785, 5,758,644, 5,685,299, 5,632,272, 5,490,505, 5,482,036, international equivalents, or one or more of the patents referenced at Products containing Satshare 2 system description system description 2 STANDALONE BACK PANEL SYMBOLS The following symbols are found on the back of the Radical-7 Docking Station and are defined below: NOTE: Some of the interfaces and symbols are not available in all versions of the Docking Station. P1 P2 P3 SYMBOLS RS-232 Rx Only SatShare interface Equipotential Ground Terminal 5 4 See Instructions for Use Fuse Replacement 1 SERIAL OUTPUT CONNECTOR 2 3 ANALOG OUTPUT / NURSE CALL CONNECTOR SATSHARE CABLE CONNECTOR Use the Serial Output Connector with a ferrite bead installed to connect a serial device, including a serial printer, RadNet Interface Module or PC, to the Radical-7. See Section 7, Serial Interface Specifications. All external device connections to the Serial Output Connector must be IEC compliant. Use the Analog Output Connector with a ferrite bead installed to interface with an analog output device, such as a chart recorder or nurse call system. All external device connections to the Analog Output / Nurse Call Connector must be IEC compliant. Use the SatShare Cable Connector to connect a SatShare cable to the SpO 2 input connector of a multiparameter patient monitor. All external device connections to the SatShare Cable Connector must be IEC compliant. SatShare cables are available to interface with most major multiparameter patient monitors. Check the label on the SatShare cable and the SatShare Directions for Use to ensure that the correct cable is used for each type of patient monitor. Refer to Section 10 - Accessories of this manual or the Masimo web site at for the latest SatShare cables and validated instruments. Analog Out Interface Nurse Call Interface WEEE Compliant Radical-7 monitor interface In addition to being a full-featured Handheld and Standalone Pulse Oximeter, the Radical-7 s unique SatShare interface links the Radical-7 to most existing multiparameter patient monitors through the pulse oximetry patient cable or SpO 2 input connector. 4 POWER ENTRY MODULE The power entry module contains the input connector for AC power and two fuses. The AC input provides power to the system from the AC line. Always connect the pulse oximeter to the mains power for continuous and/or battery recharging. NOTE: Use the power cord as the means to disconnect the device from the mains power supply. 5 EQUIPOTENTIAL GROUND CONNECTOR Use the Equipotential Ground Connector for grounding. Upgrades any approved and validated monitor to Masimo SET performance by using the calculated SpO 2 and pulse rate determined by Radical-7 to simulate an ideal waveform, which is sent to the validated multiparameter patient monitor. Connects into the SpO 2 patient cable or SpO 2 input connector of the multiparameter patient monitor. Refer to Section 3, SatShare Setup and Section 4, SatShare Operation for additional details. 2-8 Radical-7 Signal Extraction Pulse Oximeter Operator s Manual Radical-7 Signal Extraction Pulse Oximeter Operator s Manual 2-9

14 2 system description setup 3 CAUTION: THE WAVEFORM DISPLAYED ON THE MULTIPARAMETER PATIENT MONITOR IS A SIMULATED SIGNAL. REFER TO THE RADICAL-7 DISPLAY FOR THE PATIENT WAVEFORM. CAUTION: ONLY USE A SATSHARE CABLE THAT HAS A FERRITE BEAD INSTALLED. Introduction Before the Radical-7 can be used in a clinical setting, it needs to be inspected, properly setup and the batteries need to be fully charged. Unpacking and inspection Remove the instrument from the shipping carton and examine it for signs of shipping damage. Check all materials against the packing list. Save all packing materials, invoice and bill of lading. These may be required to process a claim with the carrier. If anything is missing or damaged, contact the Technical Service Department. The contact address and phone numbers are listed in Section 9, Service and Repair. Preparation for monitoring The following sections of the manual describe the preparation, set-up and initial installation of the Radical-7 Pulse Oximeter. RADICAL-7 POWER REQUIREMENTS Always use a hospital grade, AC power cable to connect the Radical-7 to an AC power source. Do not connect the Radical-7 Docking Station to an AC outlet controlled by a switch. Verify the AC power voltage and frequency before use. Verify that the power source can provide adequate power rating as indicated on the rear panel of the Radical-7 Docking Station. The Radical-7 is designed to operate on 100 to 240VAC, Hz. The device is rated at 55 VA max. Connect a hospital grade power cable to the power entry module of the Radical-7 unit (IEC-320 connector type at the Radical). Connect the power cable to an AC power source. Ensure that the unit is adequately powered by verifying that the AC power indicator on the Docking Station is illuminated. CAUTION: FOR HOSPITAL USE, CONNECT ONLY TO A HOSPITAL GRADE RECEPTACLE. DO NOT UNDER ANY CIRCUMSTANCES REMOVE THE GROUNDING CONDUCTOR FROM THE POWER PLUG. DO NOT USE EXTENSION CORDS OR ADAPTERS OF ANY TYPE. THE POWER CORD AND PLUG MUST BE INTACT AND UNDAMAGED. USE THE POWER CORD AS THE MEANS TO DISCONNECT THE DEVICE FROM THE MAINS POWER SUPPLY Radical-7 Signal Extraction Pulse Oximeter Operator s Manual Radical-7 Signal Extraction Pulse Oximeter Operator s Manual 3-1

15 3 setup setup 3 IF THERE IS ANY DOUBT ABOUT THE INTEGRITY OF THE PROTECTIVE EARTH CONDUCTOR ARRANGEMENT, OPERATE THE OXIMETER ON INTERNAL BATTERY POWER UNTIL THE AC POWER SUPPLY PROTECTIVE CONDUCTOR IS FULLY FUNCTIONAL. TO ENSURE PATIENT ELECTRICAL ISOLATION, CONNECT ONLY TO OTHER EQUIPMENT WITH ELECTRICALLY ISOLATED CIRCUITS. DO NOT CONNECT TO AN ELECTRICAL OUTLET CONTROLLED BY A WALL SWITCH OR DIMMER. INITIAL BATTERY CHARGING Before use, the Radical-7 Handheld battery and the optional Docking Station battery needs to be fully charged. To charge the batteries, attach the Handheld unit to the Docking Station and plug in the AC power cord. Verify that the batteries are charging. The battery charging LED indicators on the Docking Station flash prior to charging and remain illuminated while the batteries are charging. Refer to Section 9, Battery Operation and Maintenance, for proper battery charging. Monitor setup The Radical-7 maintains three types of default values which will automatically revert to after a power cycle: Factory these options are restored to factory values Custom these settings can be changed by the user and retained through the power cycle. Adult / Neo these settings can be selected to revert to factory or hospital-defined values (for Adult or Neonatal) after a power cycle. The following outlines the default values the Radical-7 reverts to after a power cycle. FACTORY DEFAULT SETTINGS OPTION LCD SCREEN ILLUMINATION AC Power Battery Power SENSITIVITY DEFAULT SETTING Set to maximum, level 4 Set to minimum, level 1 Set to normal mode INITIAL INSTALLATION Place the Docking Station on a stable hard flat surface near the patient. Always place the Radical-7 unit on a dry surface. Maintain a minimum of 3 cm (1 inch) free space around the Radical-7 Standalone unit. Make sure that the Radical-7 loudspeaker is not covered to avoid a muffled alarm sound. The Radical-7 Handheld, Docking Station or Standalone should not be operated outside the following environmental conditions: CUSTOM (USER) DEFINED SETTINGS This mode is indicated by Mode Custom on the Alarms menu. The following table outlines the settings that may be changed by the user and the Radical-7 will remember after a power cycle. OPTION DISPLAY VIEW AND CONTRAST DEFAULT SETTING Set to pre-power down setting OPERATING ENVIRONMENTAL CONDITIONS AVERAGING TIME Set to pre-power down setting TEMPERATURE +5 C to +40 C, +41 F to +104 F FASTSAT Set to pre-power down setting HUMIDITY 5% to 95%, non-condensing HOME USE Set to pre-power down setting OPERATING ALTITUDE 1060 mbar to 500 mbar pressure ft to 18,000 ft (-304 m to 5,486 m) INTERFACE ALARMS SATSHARE NUMBERS Set to pre-power down setting Set to pre-power down setting Configure the unit for your regional power line frequency (50 or 60 hz) if needed. Default is 60 hz (standard for the United States). See Section 4, Operation, Config. CAUTION: THE UNIT MUST BE CONFIGURED TO MATCH YOUR LOCAL POWER LINE FREQUENCY TO ALLOW FOR THE CANCELLATION OF NOISE INTRODUCED BY FLUORESCENT LIGHTS AND OTHER SOURCES. POWER SAVE DATE AND TIME FORMAT LANGUAGE ANALOG OUTPUT SERIAL OUTPUT PORT MODE Set to pre-power down setting Set to pre-power down setting Set to pre-power down setting Set to pre-power down setting Set to pre-power down setting 3-2 Radical-7 Signal Extraction Pulse Oximeter Operator s Manual Radical-7 Signal Extraction Pulse Oximeter Operator s Manual 3-3

16 3 setup setup 3 OPTION PULSE BEEP VOLUME TREND DISPLAY PARAMETERS TREND PERIOD LOW SpO 2 ALARM LIMIT DEFAULT SETTING Set to pre-power down setting Set to pre-power down setting Set to pre-power down setting Set to pre-power down setting CAUTION: SIMULTANEOUS USE OF SATHSARE AND SERIAL PORT IS NOT SUPPORTED. SATSHARE SETUP 1. Select the SatShare cable that is appropriate for the multiparameter monitor that is being connected. Check the Masimo web site at for the latest list of available SatShare cables and validated instruments. ADULT/NEO (HOSPITAL DEFINED) SETTINGS The following table outlines settings that may be defined by the hospital. If enabled (via a password protected screen), these settings will return to pre defined values after a power cycle. This mode is indicated by Mode Adult or Mode Neo on the Alarms menu. See Section 4, Operation for details on enabling and setting these parameters. ADULT / NEO SETTING OPTION CUSTOM SETTING (PRE DEFINED) SpO 2 HIGH/LOW ALARM LIMIT PULSE RATE HIGH/LOW ALARM LIMIT ALARM SILENCE ALARM VOLUME ALARM DELAY Set to pre-power down setting Set to pre-power down setting Set to 120 seconds Set to pre-power down setting The 0 and 5 second setting is retained, the 10 second setting is set to 5 seconds Set to pre-defined Adult or Neo setting Satshare setup The Radical-7 has been proven to be accurate during patient motion and low perfusion conditions. Saturation and pulse rate values from the Radical-7 may be displayed on a multiparameter monitor through the SatShare feature. The SatShare feature provides an ideal, simulated waveform corresponding to the measured saturation and pulse rate values determined by the Masimo SET technology. This waveform may be used to display these values on multiparameter monitors through the multiparameter monitor s oximetry sensor or input connector. It is recommended that the Radical-7 is positioned close to the multiparameter monitor with the Radical-7 screen visibly displaying the plethysmographic waveform and the saturation and pulse rate measurements. 2. Connect the labeled end of the cable to the SatShare Cable Connector port on the back of the Docking Station. Tighten the connector screws for a secure connection. 3. Connect the other end of the SatShare cable either to the sensor connector of the multiparameter monitor s SpO 2 cable or directly to the SpO 2 connector on the monitor. 4. Verify that the Radical-7 recognizes the correct cable.the name of the SatShare cable will be displayed on the LCD screen when the SatShare mode is functional. 5. Set the multiparameter monitor s high and low saturation and pulse rate alarm limits as appropriate. 6. Set the multiparameter monitor's averaging time to the lowest setting (i.e. fastest response). The Radical-7 s ideal waveform necessitates the need for additional averaging by the monitor. If the multiparameter monitor's averaging time is not changed, the time to display physiological changes in saturation on the monitor will be increased with SatShare. However, the delay can be minimized by reducing the multiparameter monitor's averaging time. 7. While in the SatShare mode, if there are any significant discrepancies between the readings from the Radical-7 and those on the monitor displaying the values obtained from SatShare, the values reported by the Radical-7 are to be considered the correct values. 8. To use the Radical-7 with SatShare while it is not connected to AC power, set the Power Save parameter in the General menu to "No", refer to Section 4-Operation. Please note that if the Radical-7 is used in this mode, the length of time the Radical- 7 can operate on battery power will be significantly diminished. 9. Set the SatShare Numbers and the Interface Alarms parameters in the General menu according to Customer preference. 3-4 Radical-7 Signal Extraction Pulse Oximeter Operator s Manual Radical-7 Signal Extraction Pulse Oximeter Operator s Manual 3-5