Flair 500 Series Annunciators

Transcription

1 Flair 500 Series s

2 Basics Flair Multi-Zone s (MZAs) are fully functional, flexible, programmable micro controller based alarm control panels. They can be used independently d or in conjunction with other control panels and access control systems. Typical applications i include alarm systems where there are guards, officers, nurses or other personnel who need to monitor doors, rooms, objects or people quickly without having to scroll through LCD screens or computers FEATURES 8 Zone Modular Design Micro Controller Based Highly Visible Display Single Touch Control Easily Programmable

3 User Interface The Basic 8 Zone Module consists of 8 each, Yellow, Green, Red LEDs, and 8 Tactile Switches. Yellow LED Green LED Red LED Tactile Switch Indicates if the corresponding Zone is Bypassed. ON = Bypassed Indicates the Status of the Zone Input in real-time. ON = Zone Secure OFF = Zone Faulted Flashing = Zone Trouble Indicates a Zone Alarm. Flashing = New Alarm Steady = Acknowledged Alarm Provides for Individual Zone Control Acknowledge (Press Once) Reset (Press Once after Ack.) Bypass (Hold for 1 ½ seconds) Typical 8 Zone Display

4 Inputs of the MZA Zone Inputs Consist of eight Supervised Loop Inputs with one Common. Zone Inputs may be independently programmed for any one of five Input Types. N.C./N.O. N.C. N.O. Fire High Security Back of MZA Zone Inputs Cont trol In Control Inputs Consist of four Digital Control Inputs with one Common. Control Inputs may be independently programmed for any one of six Control Types Individual Out Com. Out Acknowledge Reset Shunt Disable Shunt Disable w/ Memory Arm/Disarm Lamp Test Serial Port 12 Vdc

5 N.C./N.O - Zone Input Configuration For use with N.C. and or N.O. contacts. N.C/N.O. EOL Zones must have a 1000 Ohm resistor across them. If the Zone is Shorted or Open, it will Alarm, there is no Trouble condition. Resistors should always be placed at the end of the wire run.

6 N.C. - Zone Input Configuration For use with N.C. contacts. N.C. EOL Zones must have a 1000 Ohm resistor across them. An Open Zone will generate an Alarm condition. A Shorted Zone will generate a Trouble condition.

7 N.O./Fire - Zone Input Configuration For use with N.O. Contacts. N.O. EOL Zones must have a 1000 Ohm resistor across them. A Shorted Zone will generate an Alarm condition. An Open Zone will generate a Trouble condition.

8 High Security - Zone Input Configuration High Security EOL Zones monitor for 7 different Loop Resistance Ranges. Secure Loop = 2000 Ohms Alarm Loop = 5300 Ohms Magnetic Tamper = 1000 Ohms Loop Tamper = Short Open and Loop Tamper = Short, Open and ranges above and below the Secure Loop Resistance

9 Individual Outputs Consist of eight Open Collector Transistor Outputs, each with a maximum switch current of 100mA 24VDC. Individual Outputs may be programmed for any one of five Output Types Non-Latch Latched Pulsed Timed Sounder Outputs of the MZA Back of MZA Zone Inputs Cont trol In Common Outputs Consist of two Open Collector Transistor Outputs, each with a maximum switch current of 100mA 24VDC, typically factory wired to an Audible Sounder and Common Relay Output. Common Outputs may be programmed for any one of six Output t Types Non-Latch Latched Pulsed tpulsed Timed Sounder System Arm Serial Port Individual Out Com. Out 12 Vdc

10 Zone Output Configurations The 8 Individual Outputs act as a switch to ground and may be connected to a small audible device, LED lamp, low current relay w/ surge diode, input of a digital device (PLC, Digital it Dialer, Alarm Panel, or PC) etc Non-Latch Follows the Status of the Zone Input, automatically resetting when the Zone Input is Secure. Latched Output will remain activated upon Alarm until the Zone Input is Secure and the Zone has been Acknowledged and Reset. Pulsed Output will activate upon Alarm for a 3 Second Period, each time the Zone Input is Alarmed. Timed Output will activate upon Alarm for a pre-programmed Time Period, then Automatically Reset. Sounder Output will activate upon Alarm and remain on until the Zone has been Acknowledged.

11 Configuring the MZA Characteristics of the Inputs and Outputs of each MZA Module are easily configured with the use of the Flair one page MZA Configuration software. Input Types Entry/Exit Delays Door Prop Delays Output Types Output Mapping

12 Input to Output Mapping Any Outputs may be configured to operate with any individual Input or combination of Inputs. Connect Multiple Zones to a Single Output for control of: Digital Dialers Camera Switchers DVR s Voice s Lighting Sirens Output Mapping

13 Communication Module Communication Status LEDs Operation Status LEDs ICSP Port 12 Vdc PC Serial Port Output Expansion Port Relay Drivers RS485 Port 1 RS485 Port 2 RS485 Port 3 RS485 Port 4 Link Port

14 Communication Module Basics The Communication Module (CM) is an accessory to the that controls and routes RS485 Serial Communication between two or more Cabinets Local/Remote The CM can be used to connect a Local Cabinet to one or more Remote Cabinets, each with complete display and control of the Local Zones. Multiplex up to 512 Zones FEATURES Micro Controller o Based Easily Programmable Individual Status LEDs

15 RS485 Ports Each CM has four RS485 Ports to connect up to four Cabinets in Local/Remote Configuration, with one Cabinet on each of the four RS485 Ports. Local Cabinets are typically hard wired to sensors in the surrounding building and display the status of those inputs. Remote Cabinets provide visual display and control of a Local Cabinet at one or more other locations. Each RS485 Port can be configured as either Local or Remote. A Local Cabinet may be routed to several Remote Cabinets. A Remote Cabinet may only be routed to one Local Cabinet.

16 CM Link Port The CM Link Port can be used to connect two Communication Modules together, in order to expand the number of Local/Remote Cabinets multiplexed to eight and/or to Link Local/Remote Cabinets over the Internet or a wireless transceiver. PC Serial Port The PC Serial Port is used to Configure the CM using a standard PC with an RS232 Serial Port.

17 Configuring the CM The Communication Module is easily configured with a standard PC, via the PC Serial Port, using the Flair one page CM Configuration Software. Configurable Features: Routing of Local Cabinet to one or more Remote Cabinets. Output Expansion Port Features Virtual MZA CM Link Port Routing

18 Application Profiles Social Services Duress Alarm School/University Alarm Estate Upgrade/Retro-fit Existing Alarm Panel Access Control

19 Social Services Duress Alarm 503A-24 Local Telecom Room 3 rd Floor 503A-24 Local RS485 RS485 PORT CM COMMUNICATION MODULE RS485 PORT 2 Telecom Room 2 nd Floor 561R-72 Remote 503A-24 Local Telecom Room 1 st Floor Guard Station 1 st Floor Lobby

20 School/University Alarm 503A-12 Local Mathematics/Science Building 503A-12 Local Technology Building 503A-12 Local Liberal Arts Building 503A-12 Local Performing Arts Building RS485 RS485 PORT CM COMMUNICATION MODULE Local Sensors Door Window PIR RS485 PORT 2 561BC-72 Local/Remote Security Office Administration Building

21 Estate Security Zone Inputs 503A-48 Local Door Window PIR Sensors Tele-Com Utility Room 550A-48 Remote Graphic Office RS485 PORT 1 500CM Communication Module RS485 PORT 2 RS485 PORT 3 RS485 PORT 4 550A-48 Remote Graphic Master Bedroom 550A-48 Remote Graphic

22 Upgrade/Retro-fit Existing Alarm Panel Existing Sensors Door Window PIR Existing Field Wiring Existing Zone Inputs Existing Local Alarm Panel Zone Inputs Guard Station 1 st Floor Lobby 550A-48 Local Graphic RS485 PORT 1 500CM Communication Module Individual Outputs CM Link Port Ethernet to RS485 Converter LAN WAN RS485 to Ethernet Converter CM Link Port Remote Site 500CM Communication Module RS485 PORT 1 561BC-48 Remote

23 Access Control Card Reader KeyPad Door Sensor Door Control Access Control Panel Guard Station 1 st Floor Lobby Zone Inputs 561R-48 Local RS485 PORT 1 Remote Site 561BC-48 Remote RS485 PORT 1 500CM Communication Module CM Link Port RS485 CM Link Port 500CM Communication Module

24 Simple Access Control Card Reader KeyPad DPST Door Sensor Door Control Guard Station 1 st Floor Lobby Zone Inputs 561R-48 Local