ITC 2000 HEATING CONTROL CABINET. Installation & Operation Manual

Size: px
Start display at page:

Download "ITC 2000 HEATING CONTROL CABINET. Installation & Operation Manual"

Transcription

1 ITC 2000 HEATING CONTROL CABINET Installation & Operation Manual VTI, Incorporated 24 McMillan Way Newark, DE Phone (302) FAX (302) Revision Level 0.03 Manual No June, 1997 TO INSURE PROPER INSTALLATION, THIS MANUAL MUST BE READ PRIOR TO STARTING THE INSTALLATION PROCESS.

2 1. INTRODUCTION This manual covers installation instructions and operation for the ITC 2000 Series Heating Control Cabinets consisting of Model ITC 2024 with provisions for 24 TCM 100 Temperature Control Modules or Model ITC 2036 with provisions for 36 TCM 100 Temperature Control Modules. 1.1 REFERENCE DRAWINGS E IT2024 MAIN CABINET ASSEMBLY E ITC2024 SINGLE LINE WIRING DIAGRAM E ITC2036 MAIN CABINET ASSEMBLY E ITC2036 SINGLE LINE WIRING DIAGRAM E TCM100 MAIN ASSEMBLY B TCM100 SCHEMATIC 2. GENERAL DESCRIPTION The ITC2000 Series Heating Control Cabinets consist of an enclosure, similar to a motor control center, containing a power transformer compartment, a distribution compartment and a temperature control module compartment. The cabinet also contains vertical and horizontal wireways for routing heater and control cables as well as a compartment for the alarm monitor PC board. The power transformer compartment accommodates either a 45 KVA (ITC 2036) or a 30 KVA (ITC 2024) three phase power transformer with a 480 VAC delta primary and 208/120 VAC wye secondary. A transformer with a 600 VAC delta primary may be provided as an option. If required for higher voltage heater, VTI can also provide a three phase power transformer with a 240/138 VAC wye secondary as an option. The primary feed to the transformer is routed through a 1 1/2 conduit located in the rear of the cabinet and extending vertically from the top of the cabinet to the transformer compartment in the bottom of the cabinet. A chimney is provided in the rear of the cabinet to vent the heat from the transformer out the top of the cabinet. The distribution compartment is located above the transformer in the center of the cabinet. This compartment contains either three (ITC 2036) or two (ITC 2024) 24 position panel boards each capable of accepting 12 two pole 25 Amp circuit breakers plus a three pole 250 VAC 150 Amp (ITC 2036) or 100 Amp (ITC 2024) secondary circuit breaker to coordinate with the power transformer. Each two pole branch circuit breaker is designed to protect one of the 36 (ITC 2036) or 24 (ITC 2024) tcm100 control circuits. The 120 VAC or 208 VAC voltage to the tem100 controller is determined by connecting one of the power feed wires from the circuit breaker to the tcm100 to either the second pole of the circuit breaker for 208 VAC operation or an adjacent neutral bus for 120 VAC operation. This compartment is

3 thermally isolated from the transformer compartment via fiberglass insulation and also contains a vent into the chimney to allow heat from the circuit breakers to escape out the top of the cabinet. The module compartment contains three (ITC 2036) or two (ITC 2024) 12 position racks each capable of accepting up to 12 tcm100 Temperature Control Modules. Each tcm100 module may be configured to operate from either a common ambient temperature sensor, such as a VTI TS10A, or a separate pipe temperature sensor, such as a VTI PTS100, to control heater power. Each tcm100 Temperature Control Module contains a power switching contactor, heater current indicator, high and low current alarms, GFI alarm, as well as power line low voltage and heater continuity alarm circuits. The output from each tcm100 Temperature Control Module is connected to a terminal block located in the terminal compartment to facilitate customer heater load connections. The alarms from all tcm100 Temperature Controllers are connected together via a back plane which in turn is connected to a master alarm relay located in the top compartment. A power fail relay is also provided in this compartment of the cabinet. The output from these two relays are wired to terminals in the terminal compartment for customer connection. 3. CABINET INSTALLATION Move the ITC2000 Series Heating Control Cabinet to the desired location and remove the shipping crate. Remove the field wiring entry plate on top of the cabinet to obtain access to wireways. Make sure that the main 120/208 VAC circuit breaker is in the OFF position. Remove the transformer compartment cover, load terminal compartment cover, alarm compartment cover, and horizontal wireway cover to obtain access for field wiring. The ITC2000 Heating Control Cabinet as shipped from the factory contains the tcm1000 Series Controllers configured as requested at time of order. If no configuration instructions were included with order, all modules are shipped with default configuration values. Before energizing the equipment, verify that the controllers are configured properly to prevent damage to the module.

4 4. CABINET WIRING 4.1 LOAD WIRING Select a wire type and gauge that will meet NEC safety and design requirements to minimize voltage drop from the controller output to the heater loads (recommended size is #10 AWG). Ensure that each cable from the heater junction box or PTS100 Temperature Sensor is electrically disconnected from all power sources prior to handling. Pull the cable from each heater junction box or PTS100 Temperature Sensor to the ITC2000 Cabinet and route through the field wiring entry in the top of the cabinet across the horizontal wireway and into the load terminal compartment. Cut and strip the cable for termination on the appropriate load terminal block. Prior to connecting the wires to the load terminal block, use a MEGGER to verify the integrity of the insulation in the cold lead wire and heater cable. The insulation resistance of each wire measured between conductor and ground with 2500 VDC applied must be greater than 20 Megohms. If the wires test normal, proceed to connect the heating load circuits as shown in details F1, F2, F3, or F4 on VTI Single Line Diagram E (ITC 2036) or E (ITC 2024) for the type of circuit configuration selected for the particular application. If the MEGGER test indicates abnormally low resistance, inspect the heater cable for chafed insulation or wrong connections. Correct the high leakage condition before connecting the cable to the load terminal blocks. 4.2 MODULE VOLTAGE SELECTION The operating voltage of each tcm100 Temperature Control Module must be configured to match the operating voltage of the heating cable. Each tcm100 Heating Control Module is capable of operating on 120 VAC or 208 VAC. This voltage is selected by connecting the wire from pin 4 of each tcm100 Temperature Control Module to either the second (lower) pole of the corresponding two pole 25 Amp circuit breaker for 208 VAC operation or to the neutral bus for operation on 120 VAC. If the appropriate configuration information has not been provided at time of shipment, VTI will ship the ITC2000 cabinet with default configuration which is 120 VAC. 4.3 AMBIENT TEMPERATURE SENSOR WIRING If the tcm100 modules installed in the ITC2000 Series Cabinet are to be used in an ambient temperature sensing mode, an ambient temperature sensor must be connected to the terminal block TB2 located on the alarm PC board ( ) mounted in the alarm compartment. If a capillary type mechanical thermostat is used for this purpose, the thermostat cable connects to terminals TB2 4 and TB2 5. If a Model TS10A Electronic Ambient Temperature Sensor is utilized, the control and power connections are detailed in the table below:

5 FUNCTION 120VAC hot 120VAC neutral Control Control Ground TS10A TERMINAL TB1 2 TB1 3 TB1 4 TB1 5 TB1 G ITC2000 TERMINAL TB2 3 TB2 2 TB2 5 TB2 4 TB2 1 WARNING: THE TS10A TEMPERATURE SENSOR MAY BE SHIPPED FROM THE FACTORY WITH A JUMPER BETWEEN TERMINAL BLOCK TB1 2 AND TB1 5 OR TB1 3 AND TB1 5. THIS JUMPER SHOULD BE REMOVED WHEN OPERATING WITH AN ITC2000 CABINET TO PREVENT APPLYING LINE POTENTIAL TO THE LOW VOLTAGE DC SIGNAL INPUT!! Ensure that the cable from the field thermostat or temperature sensor is electrically disconnected from all power sources prior to handling. Pull the cable from the thermostat or TS10A Ambient Temperature Sensor to the ITC2000 Series Cabinet and route through the field wiring entry in the top of the cabinet to the alarm compartment. Cut and strip the cable for termination on terminal block TB2. Prior to connecting the wires to the load terminal block, Hypot the conductors to ground to verify the integrity of the insulation with 1200 VAC. If the leakage current is less than 1 milliamps, proceed to connect the ambient temperature sensor conductors to TB2. If a shield or ground is provided in the cable, connect it to terminal point TB2 1. It is recommended to use at least a number 14 AWG wire for the ambient temperature sensor conductors. 4.4 ALARM OUTPUT WIRING The ITC2000 Series Heating Control enclosure is supplied with an alarm PC board assembly ( ) which functions in conjunction with each tcm100 module to provide a master alarm output. The contacts of the master alarm relay are combined with the contacts of a incoming power fail relay to provide several modes of operation. Terminals TB1 A NO s are connected to a circuit which will provide a contact closure if either the power fails to the cabinet or if any of the tcm100 modules detect an alarm condition. Terminals TB1 A NC are connected to a circuit which will provide a contact opening if either the power fails to the cabinet or if any of the tcm100 modules detect an alarm condition. Terminals TB1 A PF are contacts of the power fail relay and may be configured on the printed circuit board for either close on alarm or open on alarm operation. Prior to connecting the field cables to the alarm terminals, Hypot each of the conductors at 1200 VAC to verify the integrity of the circuit insulation. If the leakage current is less than 1 milliamp, proceed to connect the field cable to the terminals to provide the desired response. If the cable has appreciable leakage to ground, stop testing and repair the cable prior to proceeding.

6 4.5 FEEDER WIRING WARNING: MAKE SURE THAT THE THREE PHASE 480/600 VOLT, 60 HZ CIRCUIT BREAKER OR DISCONNECT SWITCH WHICH WILL FEED POWER TO THE CABINET IS DE ENERGIZED AND LOCKED OUT BEFORE ATTEMPTING TO PULL THE FEEDER CABLE TO THE SERIES ITC2000 CABINET! Based on the transformer rating of the ITC2000 cabinet, pull appropriately sized four conductor cable from the main disconnect switch or circuit breaker through the input power conduit at the top of the cabinet. DO NOT CONNECT EITHER END AT THIS TIME! The minimum size wire is listed in the table below: MODEL# ITC 2036 ITC 2024 CABLE SIZE FOR 480 VAC PRIMARY KVA RATING 45 KVA 30 KVA WIRE SIZE 6 AWG 8 AWG CABLE SIZE FOR 600 VAC PRIMARY MODEL# KVA RATING WIRE SIZE ITC KVA 6 AWG ITC KVA 10 AWG Now terminate the feeder wiring at the transformer located in the compartment at the bottom of the ITC2000 Series Cabinet. Connect the three phase conductors in the cable (black, blue, and red) to the transformer primary terminals identified at H1, H2, and H3 respectively. Connect the ground conductor (green) to the ground lug provided in the transformer compartment of the cabinet. Make sure that these terminations are secure. DO NOT CONNECT THE FEEDER WIRING TO THE POWER SOURCE AT THIS TIME! Measure the phase to phase voltage of the power source that will feed the ITC2000 Cabinet. Referring to the tap chart on the transformer, connect the numbered taps on each coil which correspond most closely with the measured source voltage as shown in the table below: 480 VOLT TRANSFORMER TAP CHART Line Voltage Tap Number 1 2

7 VOLT TRANSFORMER TAP CHART Line Voltage Tap Number Replace the cover on the transformer compartment after completing the voltage tap adjustment. Ensure that the secondary circuit breaker and the 36 (ITC 2036) or 24 (ITC 2024) circuit breakers on the ITC2000 Cabinet are all in the OFF position. Hypot each of the three phase line feeders at 2000 VAC to insure the integrity of the circuit. If the leakage current is less than 1 milliamp, proceed to connect the ground wire in the feeder cable to the ground lug at the feeder supply point. Now proceed to connect each of the three phase conductors in the feeder cable to the circuit breaker or disconnect switch at the feeder supply point. This completes the installation of the series ITC2000 cabinet.

8 5. OPERATION 5.1 MODULE CONFIGURATION The input voltage for the tcm100 Temperature Control Modules is factory set for operation on 120 VAC or 208 VAC. The input voltage for the tcm101 Temperature Control Modules is factory set for operation on 240 VAC. Other than this distinction, the tcm101 functions identically to the tcm100 and the term tcm100 is used generically throughout this manual to represent both controllers. If the customer has provided configuration data at the time of purchase or even prior to shipment of the equipment, the tcm100 Temperature Control Modules would be configured as requested by the customer during final test. If not, the tcm100 module is configured and shipped as described in the table below: DESIG PARAMETER CONFIGURED JP2/3 Control Source Ambient JP4 Sensor type PTS100 JP1 Heater Type Two Wire JP5 High Current Time Delay 1.1 Minutes DP1 High Current Alarm Disabled DP2 Low Current Alarm Disabled DP3 Ground Fault Alarm 30 Milliamps If the tcm100 Temperature Control Modules require field configuration, proceed with the following: Remove each of the tcm100 Temperature Control Modules from the rack by first loosening the retaining screw at the top center of the module and then turning the ejection wing screw in the upper left hand corner of the front panel in the clockwise direction until the module disconnects from the rack connector. Withdraw the tcm100 Temperature Control Module from the rack and configure each controller for the desired operating voltage, operating mode, and alarm setpoints. The operating mode and alarm setpoints must be programmed by moving the appropriate jump jax to the desired position as described in the table below:

9 DESIG PARAMETER JP2/3 Control Source JP4 Sensor type JP1 Heater Type JP5 High Current Time Delay DP1 High Current Alarm DP2 Low Current Alarm DP3 Ground Fault Alarm SELECTIONS Ambient or Pipe Sensor Contact (thermostat) or PTS100 Two Wire or Three Wire 1.1, 2.3, or 4.5 Minutes Disable, 3, 4, 5, 8, 10, 15, 20 Amps Disable, 1, 2, 3, 5, 7, 10, 15 Amps 30, 50, 70, 100 Milliamps After the configuration has been completed for each module, plug the tcm100 module into the proper rack slot. Verify that the controller is completely seated in the rack with the back surface of front panel touching the front mounting rail. If the module does not appear to be seated completely, try removing the controller from the rack and then forcefully plugging the controller into the rack position to fully engage the connector. Each of the six contacts in the connector rated at 30 Amps and therefore requires considerable force to engage and withdraw the two parts of the connector. 5.2 POWERING THE ENCLOSURE Apply power to the ITC2000 enclosure by closing the fused disconnect switch or circuit breaker that feeds the cabinet. Now switch the main circuit breaker on the front of the ITC2000 cabinet to the ON position. This provides power to each of the individual branch circuit breakers. To energize any of the individual tcm100 Temperature Control Modules, simply switch the corresponding circuit breaker to the ON position. If the load is connected properly, the green CONTINUITY & VOLTAGE LED should illuminate. If heat is required, as sensed by either the pipe sensor or ambient sensor, the yellow TEMPLOW LED will illuminate and power will be applied to the heater. No red ALARM indications should appear. If the heater current exceeds the High Current Alarm setpoint after the selected time delay, the red HIGH CURRENT LED alarm indicator as well as the red master ALARM LED indicator will illuminate and the master alarm relay will be energized. The HIGH CURRENT and master ALARM indications as well as the alarm relay may be cleared/de energized by momentarily depressing the RESET push button on the front panel.

10 If the heater current decreases below the Low Current Alarm setpoint for more than 5 seconds, the red LOW CURRENT LED alarm indicator as well as the red master ALARM LED indicator will illuminate and the master alarm relay may be cleared/de energized by momentarily depressing the RESET push button on the front panel. If the leakage current in the heater load circuit exceeds the ground fault current setpoint, the red GFI LED alarm indicator as well as the red master ALARM LED indicator will illuminate and the master alarm relay will be energized. The controller will also disconnect both legs of the heater circuit, thereby removing power from the load and interrupting the ground fault condition. The GFI and master alarm indications as well as the alarm relay may be cleared/de energized by momentarily depressing the RESET push button on the front panel. The tcm100 Temperature Control Module may be tested when not powering the load by momentarily depressing the TEST push button on the front panel. As long as the TEST push button is depressed, power will be applied to the heater, the master alarm relay will be energized, and the ALARM LED will be illuminated for test purposes. If High Current Alarm, Low Current Alarm, or Ground Fault Alarm conditions exist, these indicators will also be lit. This completes the configuration and operation of the tcm100 Temperature Control Module.

11 6. ADDENDUM REFERENCE DRAWINGS E ITC2024 MAIN CABINET ASSEMBLY E ITC2024 SUB ASSEMBLY E ITC2024 CABINET WIRING E ITC2024 GROUNDING DRAWING E ITC2024 LABELING DRAWING E ITC2024 SINGLE LINE WIRING DIAGRAM E ITC2036 MAIN CABINET ASSEMBLY E ITC2036 SUB ASSEMBLY E ITC2036 GROUNDING DRAWING E ITC2036 LABELING DRAWING E ITC2036 CABINET WIRING E ITC2036 SINGLE LINE WIRING DIAGRAM E TCM100 MAIN ASSEMBLY B TCM100 SCHEMATIC C PTS100 MAIN ASSEMBLY C PTS100 PC ASSEMBLY C PTS100 SCHEMATIC

tcm100, tcm101 Series Temperature Control Modules and PTS100, PTS100/3 Pipe Temperature Sensors Operations Manual

tcm100, tcm101 Series Temperature Control Modules and PTS100, PTS100/3 Pipe Temperature Sensors Operations Manual tcm100, tcm101 Series Temperature Control Modules and PTS100, PTS100/3 Pipe Temperature Sensors Operations Manual This manual covers operation of the tcm100 and tcm101 Series Temperature Control Modules.

More information

Pipe Freeze Protection Control SCFP-CO-F130 Installation and Operation Manual

Pipe Freeze Protection Control SCFP-CO-F130 Installation and Operation Manual MANUAL Pipe Freeze Protection Control SCFP-CO-F130 Installation and Operation Manual Model FPT 130 Single Point Freeze Protection Heat Trace Control Table of Contents SCFP-CO-F130 Overview... 3 Installation...

More information

Single Point Freeze Protection Heat Trace Control TRACON MODEL FPT 130 Installation and Operation Manual

Single Point Freeze Protection Heat Trace Control TRACON MODEL FPT 130 Installation and Operation Manual We manage heat MANUAL Single Point Freeze Protection Heat Trace Control TRACON MODEL FPT 130 Installation and Operation Manual 1850 N Sheridan Street South Bend, Indiana 46628 (574) 233-1202 or (800) 234-4239

More information

MODEL FPT-130 SINGLE POINT FREEZE PROTECTION HEAT TRACE CONTROL

MODEL FPT-130 SINGLE POINT FREEZE PROTECTION HEAT TRACE CONTROL TRACON MODEL FPT-130 SINGLE POINT FREEZE PROTECTION HEAT TRACE CONTROL TABLE OF CONTENTS FPT 130 Overview... 2 Installation... 3 Power Source and Load Connections... 4 Temperature Sensor... 5 External

More information

MODEL GPT-130 SINGLE POINT HEAT TRACE CONTROL THERMOSTAT

MODEL GPT-130 SINGLE POINT HEAT TRACE CONTROL THERMOSTAT TRACON MODEL GPT-130 SINGLE POINT HEAT TRACE CONTROL THERMOSTAT TABLE OF CONTENTS GPT 130 Overview... 2 Installation... 3 Power Source and Load Connection... 4 Temperature Sensor Installation... 5 Panel

More information

MANUAL RESET ALARM RELEASE

MANUAL RESET ALARM RELEASE Fire Door Release MODEL AR-D MANUAL RESET ALARM RELEASE INSTRUCTION MANUAL AR-D GENERAL INFORMATION 1. Review all installation instructions, procedures, cautions and warnings contained within this manual

More information

VTI MODEL itc5000 HEAT TRACING CONTROL SYSTEM OPERATIONS MANUAL

VTI MODEL itc5000 HEAT TRACING CONTROL SYSTEM OPERATIONS MANUAL VTI MODEL itc5000 HEAT TRACING CONTROL SYSTEM OPERATIONS MANUAL 1 Operations Manual for the VTI Model itc5000 Heat Tracing Control System Description The VTI Model itc5000 Heat Tracing Control System consists

More information

ACSI MODEL 1410 POWER SUPPLY INSTALLATION INSTRUCTIONS

ACSI MODEL 1410 POWER SUPPLY INSTALLATION INSTRUCTIONS II 1400-3 ACSI MODEL 1410 POWER SUPPLY INSTALLATION INSTRUCTIONS Features: For use with doors or groups of doors that must interlock with each other to regulate control of accessing one area from another,

More information

QUICK REFERENCE GUIDE P.C. BOARD/WALL THERMOSTAT FOR 6536A891, 6536B891 & 6536C891 TWO TON PACKAGED HEAT PUMPS

QUICK REFERENCE GUIDE P.C. BOARD/WALL THERMOSTAT FOR 6536A891, 6536B891 & 6536C891 TWO TON PACKAGED HEAT PUMPS QUICK REFERENCE GUIDE P.C. BOARD/WALL THERMOSTAT FOR 6536A891, 6536B891 & 6536C891 TWO TON PACKAGED HEAT PUMPS Note: This manual may also be used for 6536-871 series heat pumps if the 6535-3209 Replacement

More information

Dual Point General Purpose Heat Trace Control TRACON MODEL GPT 230 Installation and Operation Manual

Dual Point General Purpose Heat Trace Control TRACON MODEL GPT 230 Installation and Operation Manual We manage heat MANUAL Dual Point General Purpose Heat Trace Control TRACON MODEL GPT 230 Installation and Operation Manual 1850 N Sheridan Street South Bend, Indiana 46628 (574) 233-1202 or (800) 234-4239

More information

Dual Point General Purpose Heat Trace Control TRACON MODEL GPT 230 Installation and Operation Manual

Dual Point General Purpose Heat Trace Control TRACON MODEL GPT 230 Installation and Operation Manual We manage heat MANUAL Dual Point General Purpose Heat Trace Control TRACON MODEL GPT 230 Installation and Operation Manual 1850 N Sheridan Street South Bend, Indiana 46628 (574) 233-1202 or (800) 234-4239

More information

ACSI AO ELECTRIC LATCH RETRACTION CONTROLLER INSTALLATION INSTRUCTIONS I.D. 1089, REV. F

ACSI AO ELECTRIC LATCH RETRACTION CONTROLLER INSTALLATION INSTRUCTIONS I.D. 1089, REV. F II 1400-2 ACSI 1406-04-AO ELECTRIC LATCH RETRACTION CONTROLLER INSTALLATION INSTRUCTIONS I.D. 1089, REV. F INSTALLATION Transformer Model BE31763001 by Basler Electric, Transformer Model 2010028 by Galaxy

More information

Installation Instructions

Installation Instructions 50ZPB, C, 50ZHB, C, PA3Z ---A, PH3Z ---A, PA4Z, PH4Z, PAJ4,PHJ4,WJA4,WJH4 SMALL PACKAGED PRODUCTS (SPP) Accessory Electric Heaters 5---20 kw For 14 SEER, R---410A Manufactured Home Installation Instructions

More information

Powerohm Resistors Digital HRG System

Powerohm Resistors Digital HRG System Installation and Operating Instructions Powerohm Resistors Digital HRG System This manual provides general information, installation, operation, maintenance, and system setup information for the Powerohm

More information

SAFETY INFORMATION AND WARNINGS

SAFETY INFORMATION AND WARNINGS This manual refers to the Model SST-3 control panel manufactured since October 31, 2013, which uses a universal (100 277 VAC; 50/60 Hz) power supply. Older units use a voltage-specific power supply and

More information

Model GPT 3 Freeze Protection Thermostat

Model GPT 3 Freeze Protection Thermostat We manage heat Model GPT 3 Freeze Protection Thermostat Part Number 19425 Installation and Operation Manual Environmental Technology, Inc. 1850 N Sheridan Street South Bend, Indiana 46628 (574) 233-1202

More information

F PC and AO OUTPUT BOARDS INSTRUCTION MANUAL. Blue-White. Industries, Ltd.

F PC and AO OUTPUT BOARDS INSTRUCTION MANUAL. Blue-White. Industries, Ltd. F-2000 PC and AO OUTPUT BOARDS INSTRUCTION MANUAL Blue-White R Industries, Ltd. 500 Business Drive Huntington Beach, CA 92649 USA Phone: 714-89-8529 FAX: 714-894-9492 E mail: sales@blue-white.com or techsupport@blue-white.com

More information

MODEL AC-SCC-5 INSTALLATION, OPERATION & MAINTENANCE MANUAL

MODEL AC-SCC-5 INSTALLATION, OPERATION & MAINTENANCE MANUAL 5CIM2-0413 W30-AC0056 MODEL AC-SCC-5 INSTALLATION, OPERATION & MAINTENANCE MANUAL Multi-zone Hydronic Chiller Interface Module SECTION 1: INTRODUCTION Unit description... 5 Location... 5 Handling... 5

More information

Freeze Protection Thermostat TRACON MODEL GPT 3 Installation and Operation Manual

Freeze Protection Thermostat TRACON MODEL GPT 3 Installation and Operation Manual MANUAL We manage heat Freeze Protection Thermostat TRACON MODEL GPT 3 Installation and Operation Manual Environmental Technology, Inc. 1850 N Sheridan Street South Bend, Indiana 46628 http://www.networketi.com/

More information

QUICK REFERENCE GUIDE P.C. BOARD/WALL THERMOSTAT FOR 6535D, 6537C, 6538 A&B SERIES TWO TON PACKAGED HIGH EFFICIENCY HEAT PUMPS

QUICK REFERENCE GUIDE P.C. BOARD/WALL THERMOSTAT FOR 6535D, 6537C, 6538 A&B SERIES TWO TON PACKAGED HIGH EFFICIENCY HEAT PUMPS QUICK REFERENCE GUIDE P.C. BOARD/WALL THERMOSTAT FOR 6535D, 6537C, 6538 A&B SERIES TWO TON PACKAGED HIGH EFFICIENCY HEAT PUMPS RV Products A Division of Airxcel, Inc. P.O. Box 4020 Wichita, KS 67204 1-316-832-4357

More information

American Dish Service

American Dish Service American Dish Service INSTALLATION INSTRUCTIONS Model JDS12 (T) or (R) Muffler Booster (T) 12kW, 240v, 3-ph, (R) 12kW, 208v, 3-ph Manufactured by Hubbell Electric Heater Company for use on American Dish

More information

Public Safety DAS Annunciator Panel

Public Safety DAS Annunciator Panel Public Safety DAS Annunciator Panel 120 VAC Models: 1221-A, 1221-B, 1221-C Revision D 91117 48 VDC Models: 1221-A-48, 1221-B-48, 1221-C-48 24 VDC Models: 1221A-24, 1221-B-24, 1221-C-24 CAUTION: (Read This

More information

WARNING. Installation Tip: Try out this unit before installing onto a fire door system. Test and learn the release INTRODUCTION

WARNING. Installation Tip: Try out this unit before installing onto a fire door system. Test and learn the release INTRODUCTION WARNING 1. CAUTION: Review all installation instructions, procedures, cautions and warnings contained within this manual prior to installing and/or servicing this product. As with all releasing device

More information

Sapphire Series TSVW & TWWS Chillwater Digital Thermostats

Sapphire Series TSVW & TWWS Chillwater Digital Thermostats Sapphire Series TSVW & TWWS Chillwater Digital Thermostats Table of Contents 1. Introduction 3 TSVW Main Components 3 TWWS Main Components 4 2. Display Panels for TSVW and TWWS Thermostats 4 TSVW Display

More information

INSTALLATION INSTRUCTIONS FOR MOUNTING KIT

INSTALLATION INSTRUCTIONS FOR MOUNTING KIT RV Products Division INSTALLATION INSTRUCTIONS FOR 8330-5501 MOUNTING KIT 8330-752 CONTROL BOX KIT (12 VDC COOL ONLY) 9330B755 CONTROL BOX KIT (12 VDC HEAT/COOL) 8530-750 CONTROL BOX KIT (24 VAC COOL ONLY)

More information

INSTALLATION, OPERATING & MAINTENANCE INSTRUCTIONS FOR 870 SERIES INDUSTRIAL CONTROL PANELS

INSTALLATION, OPERATING & MAINTENANCE INSTRUCTIONS FOR 870 SERIES INDUSTRIAL CONTROL PANELS INSTALLATION, OPERATING & MAINTENANCE INSTRUCTIONS FOR 870 SERIES INDUSTRIAL CONTROL PANELS GENERAL INDEECO Industrial Control Panels are designed to provide years of trouble free operation if properly

More information

Lubrication cycle IP Enclosure Rating. 110 VAC, 220/230 VAC (50/60 Hz) Alarm Fault Relay Contacts. IP-55 (Liquid tight connector)

Lubrication cycle IP Enclosure Rating. 110 VAC, 220/230 VAC (50/60 Hz) Alarm Fault Relay Contacts. IP-55 (Liquid tight connector) SMAC Controller Industrial Lubrication Systems Operation The SMAC Controller is a multi-purpose programmable controller used with industrial lubrication systems. Controller settings are saved whenever

More information

www. ElectricalPartManuals. com GADD MKIII Ground Fault Indication System Instruction Manual Ground Fault Protection

www. ElectricalPartManuals. com GADD MKIII Ground Fault Indication System Instruction Manual Ground Fault Protection Ground Fault Protection GADD MKIII Ground Fault Indication System Instruction Manual 7615 Kimbel Street, Mississauga, Ontario Canada L5S 1A8 Tel: (905)673-1553 Fax: (905)673-8472 Toll Free: 1-888-RESISTR

More information

Beacon 200 Gas Monitor Operator s Manual. Part Number: RK Released: 6/6/08

Beacon 200 Gas Monitor Operator s Manual. Part Number: RK Released: 6/6/08 Beacon 200 Gas Monitor Operator s Manual Part Number: 71-2102RK Released: 6/6/08 Table of Contents Chapter 1: Introduction.................................................3 Overview.............................................................3

More information

Model Gas Alarm Panel APPLICABILITY & EFFECTIVITY. This manual provides instructions for the following Sierra Monitor products:

Model Gas Alarm Panel APPLICABILITY & EFFECTIVITY. This manual provides instructions for the following Sierra Monitor products: Model 2102 Gas Alarm Panel APPLICABILITY & EFFECTIVITY This manual provides instructions for the following Sierra Monitor products: Model Description 2102-00 Alarm Panel 2 Channel 2102-01 Alarm Panel 2

More information

MASTER JOCKEY PUMP CONTROLLER. Model JPCE INSTRUCTION MANUAL. C 2018 Master Control Systems, Inc

MASTER JOCKEY PUMP CONTROLLER. Model JPCE INSTRUCTION MANUAL. C 2018 Master Control Systems, Inc MASTER JOCKEY PUMP CONTROLLER Model JPCE INSTRUCTION MANUAL C 2018 Master Control Systems, Inc TABLE OF CONTENTS Important Safety Information. Page 3 General Description and Installation.. Page 4 Model

More information

MASTER PRESSRE MAINTANENCE CONTROLLER. Models PMCE INSTRUCTION MANUAL. C 2018 Master Control Systems, Inc

MASTER PRESSRE MAINTANENCE CONTROLLER. Models PMCE INSTRUCTION MANUAL. C 2018 Master Control Systems, Inc MASTER PRESSRE MAINTANENCE CONTROLLER Models PMCE INSTRUCTION MANUAL C 2018 Master Control Systems, Inc TABLE OF CONTENTS Important Safety Information. Page 3 General Description and Installation.. Page

More information

Beacon 800 Gas Monitor Operator s Manual

Beacon 800 Gas Monitor Operator s Manual Beacon 800 Gas Monitor Operator s Manual Part Number: 71-0037RK Revision: F Released: 4/18/17 www.rkiinstruments.com Product Warranty RKI Instruments, Inc. warrants gas alarm equipment sold by us to be

More information

WARNING WARNING TROUBLESHOOTING GUIDE INTEGRATED FURNACE CONTROL MODULE

WARNING WARNING TROUBLESHOOTING GUIDE INTEGRATED FURNACE CONTROL MODULE TROUBLESHOOTING INTEGRATED FURNACE Failure to read and follow all instructions carefully before installing or operating this control, could cause personal injury and/ or property damage. 50A55 INTEGRATED

More information

INSTALLATION INSTRUCTIONS FOR 9330F4552 FREE DELIVERY PLENUM KITS

INSTALLATION INSTRUCTIONS FOR 9330F4552 FREE DELIVERY PLENUM KITS RV Products Division INSTALLATION INSTRUCTIONS FOR 9330F4552 FREE DELIVERY PLENUM KITS 8330-752 CONTROL BOX KIT (12 VDC COOL ONLY) 9330C755 CONTROL BOX KIT (12 VDC HEAT READY) 8530-750 CONTROL BOX KIT

More information

FlashGuard 3000B Dual Lighting System Troubleshooting Guide

FlashGuard 3000B Dual Lighting System Troubleshooting Guide FlashGuard 3000B Dual Lighting System Troubleshooting Guide Table of Contents Section Flashhead (Strobe) Troubleshooting Flowchart 1 Multiple Strobe Troubleshooting Flowchart 2 Sidelight Troubleshooting

More information

Installation Instructions

Installation Instructions 50ES--A, 50EZ--A, 50VG--A, B, 50VL--A, B, 50VR--A, 50VT--A, B 604D-- --A, 607C-- --A, B, 607E-- --A, 704D-- --A, 707C-- --A, B, 707E-- --A PA3G -- -- A, PH3G -- -- A, PA4G, PH4G PAD3, PHD3, PAD4, PHD4,

More information

TCM120. Operation Manual

TCM120. Operation Manual TCM120 Operation Manual This manual covers operation of the tcm120, tcm121, tcm122, tcm123, tcm125, and the European version tcm121e. The term tcm120 is used throughout this manual as the generic name

More information

CommStat 6. Controller for Redundant HVAC Systems PRODUCT DATA SHEET

CommStat 6. Controller for Redundant HVAC Systems PRODUCT DATA SHEET CommStat 6 Controller for Redundant HVAC Systems PRODUCT DATA SHEET General Description The CommStat 6 HVAC controller is designed for controlling up to six redundant air conditioners in an E-House or

More information

Pump-Down Controller MODEL 4052

Pump-Down Controller MODEL 4052 Pump-Down Controller 4-20mA Input/Scalable Output Seal Fail Monitoring Duplex Pump Alternation Hand-Off-Auto Controls Dual Run-time Meters RS-485/Modbus Communications DESCRIPTION The Model 4052 Pump-Down

More information

Pioneer-R16 Gas Monitor Operator s Manual

Pioneer-R16 Gas Monitor Operator s Manual Pioneer-R16 Gas Monitor Operator s Manual Edition 7/2/97 RKI INSTRUMENTS, INC RKI Instruments, Inc. 33248 Central Ave, Union City, CA 94587 (510) 441-5656 Chapter 1: Description About the Pioneer-R16 Gas

More information

SERVICE BY QUALIFIED PERSONNEL ONLY

SERVICE BY QUALIFIED PERSONNEL ONLY Installation Instructions Automatic Load Control Relay For Emergency Lighting! IMPORTANT SAFEGUARDS! WHEN USING ELECTRICAL EQUIPMENT, BASIC SAFETY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED, INCLUDING THE FOLLOWING:

More information

GTD20A Installation Instructions BRANCH CIRCUIT TRANSFER SWITCH/LIGHTING CONTROL DEVICE

GTD20A Installation Instructions BRANCH CIRCUIT TRANSFER SWITCH/LIGHTING CONTROL DEVICE Installation Instructions BRANCH CIRCUIT TRANSFER SWITCH/ CONTROL DEVICE UL 1008-BCELTS UL 924-Switch Bypass! IMPORTANT SAFEGUARDS! WHEN USING ELECTRICAL EQUIPMENT, BASIC SAFETY PRECAUTIONS SHOULD ALWAYS

More information

Emergency Lighting Transfer System Model: ELTS2 Installation and User Operation Manual

Emergency Lighting Transfer System Model: ELTS2 Installation and User Operation Manual Emergency Lighting Transfer System Model: ELTS2 Installation and User Operation Manual Part Number: 1096M1200 Rev: E Released: 2018-07 ETC is a registered trademark of Electronic Theatre Controls, Inc.

More information

Installation and Operation Manual Low Power (LP) DC Power System

Installation and Operation Manual Low Power (LP) DC Power System Installation and Operation Manual Low Power (LP) DC Power System LPS Power Enclosure LPB Battery Enclosure 2051259 R3 Information in this document is subject to change without notice and does not represent

More information

RELEASE DEVICES RELEASE DEVICE-WPS MODELS A/B INSTALLATION MANUAL U.L. LISTED CANADIAN LISTED CSFM: :100 GENERAL DESCRIPTION:

RELEASE DEVICES RELEASE DEVICE-WPS MODELS A/B INSTALLATION MANUAL U.L. LISTED CANADIAN LISTED CSFM: :100 GENERAL DESCRIPTION: RELEASE DEVICES MADE IN THE U.S.A. RELEASE DEVICE-WPS MODELS A/B INSTALLATION MANUAL U.L. LISTED CANADIAN LISTED CSFM: 7300-1418:100 GENERAL DESCRIPTION: S/N: The "WPS" World Power Series, Time Delay Release

More information

www. ElectricalPartManuals. com GADP Ground Fault Indication System Instruction Manual Ground Fault Protection

www. ElectricalPartManuals. com GADP Ground Fault Indication System Instruction Manual Ground Fault Protection Ground Fault Protection GADP Ground Fault Indication System Instruction Manual 7615 Kimbel Street, Mississauga, Ontario Canada L5S 1A8 Tel: (905)673-1553 Fax: (905)673-8472 Toll Free: 1-888-RESISTR 737-4787

More information

Electric Heat Accessory Installation Instructions

Electric Heat Accessory Installation Instructions Electric Heat Accessory Installation Instructions EBP, EBX, EBV, EBW FVM, FEM, FSM, FSU WARNING Electrical shock hazard. Installation or repairs made by unqualified persons can result in hazards to you

More information

INSTALLATION INSTRUCTIONS FOR 8330*5511 MOUNTING KIT

INSTALLATION INSTRUCTIONS FOR 8330*5511 MOUNTING KIT RV Products Division INSTALLATION INSTRUCTIONS FOR 8330*5511 MOUNTING KIT 8330-752 CONTROL BOX KIT (12 VDC COOL ONLY) 9330A755 CONTROL BOX KIT (12 VDC HEAT/COOL) 8530-750 CONTROL BOX KIT (24 VAC COOL ONLY)

More information

MANUFACTURED BY. Gus Berthold Electric Company 1900 W. Carroll Avenue Chicago, Illinois 60612

MANUFACTURED BY. Gus Berthold Electric Company 1900 W. Carroll Avenue Chicago, Illinois 60612 Installation Manual S3031-48VDC Emergency Lighting Controller MANUFACTURED BY Gus Berthold Electric Company 1900 W. Carroll Avenue Chicago, Illinois 60612 Phone: 312-243-5767 Fax: 312-243-5811 E-mail:

More information

INSTALLATION INSTRUCTIONS FOR 6532 SERIES PACKAGE HEAT PUMP

INSTALLATION INSTRUCTIONS FOR 6532 SERIES PACKAGE HEAT PUMP INSTALLATION INSTRUCTIONS FOR 6532 SERIES PACKAGE HEAT PUMP RV Products A Division of Airxcel, Inc. P.O. Box 4020 Wichita, KS 67204 1976-360 (1-02) PP TABLE OF CONTENTS 1. Warnings......................................................

More information

TraceTek Sensing Module Installation, Operation and Maintenance Instructions DESCRIPTION SPECIFICATIONS APPROVALS TYPE NM

TraceTek Sensing Module Installation, Operation and Maintenance Instructions DESCRIPTION SPECIFICATIONS APPROVALS TYPE NM TTC-1 TraceTek Sensing Module Installation, Operation and Maintenance Instructions DESCRIPTION The nvent RAYCHEM TraceTek TTC-1 sensing module is used with TraceTek sensing cables to detect liquid leaks.

More information

Pump-Up Controller MODEL 4062

Pump-Up Controller MODEL 4062 Pump-Up Controller 4-20mA Input/Scalable Output Seal Fail Monitoring Duplex Pump Alternation Hand-Off-Auto Controls Dual Run-time Meters RS-485/Modbus Communications DESCRIPTION The Model 4062 Pump-Up

More information

STATUS ALARM ALARM HISTORY POWER HISTORY RESET

STATUS ALARM ALARM HISTORY POWER HISTORY RESET Instruction Manual Model 1582-70L2 RF Switch June 2011, Rev. D CH1 AUTO CH2 SWITCH 1 2 1 2 STATUS 1 2 MODEL 1582 SWITCH CROSS TECHNOLOGIES INC. CH1 ONLINE MANUAL SELECT CH2 SWITCH MANUAL REMOTE ONLINE

More information

Installing the Cisco ONS FAP-4 Fuse Alarm Panel

Installing the Cisco ONS FAP-4 Fuse Alarm Panel Installing the Cisco ONS 15454-FAP-4 Fuse Alarm Panel Product Number: 15454-FAP-4= This document explains how to install, test, operate, and maintain the Cisco ONS 15454-FAP-4 fuse alarm panel. This document

More information

MEGA. cal electronic gas alarm. Installation, Operation, and Maintenance Instructions. Part No Rev. D Pg.

MEGA. cal electronic gas alarm. Installation, Operation, and Maintenance Instructions. Part No Rev. D Pg. WARD OXYGEN Installation, Operation, and Maintenance Instructions MEGA medical electronic gas alarm MEGA WARD MEGA medical electronic gas alarm WARD POWER SUPPLY Medical Electronic Gas Alarm OXYGEN SYSTEM

More information

PowerWave 2 Busway System

PowerWave 2 Busway System PowerWave 2 Busway System Guide Specifications (Revision 004, 11/17/2017) 1 GENERAL 1.1 Summary This specification covers the electrical characteristics and general requirements for a continuous opening,

More information

21-light Remote Annunciator. Owner s Manual

21-light Remote Annunciator. Owner s Manual 21-light Remote Annunciator Owner s Manual Annunciator Description... Inside Font Cover Detailed Specifications... 1 Environmental Specifications... 1 Power Supply Requirements... 1 Communication With

More information

Chromalox. Installation, Operation. Screw Plug Heating Solution Control Panel Assembly for Screw Plug Heaters RENEWAL PARTS IDENTIFICATION

Chromalox. Installation, Operation. Screw Plug Heating Solution Control Panel Assembly for Screw Plug Heaters RENEWAL PARTS IDENTIFICATION Chromalox Installation, Operation and RENEWAL PARTS IDENTIFICATION DIVISION SALES REFERENCE DATE 4 (Supersedes PG422-) DECEMBER, 2000 SECTION RAD PE440 6-058074-002 Screw Plug Heating Solution Control

More information

TECHNICAL DATA OBSOLETE

TECHNICAL DATA OBSOLETE Deluge Devices 270a 1. PRODUCT NAME VIKING PAR-3 Available since 1991 2. MANUFACTURED FOR: THE VIKING CORPORATION 210 N. Industrial Park Road Hastings, Michigan 49058 U.S.A. Telephone: (269) 945-9501 (877)

More information

prestige Condensing Water Boiler SERVICE TECHNICIAN S TROUBLE SHOOTING GUIDE TSG-SOLO-9/04

prestige Condensing Water Boiler SERVICE TECHNICIAN S TROUBLE SHOOTING GUIDE TSG-SOLO-9/04 prestige Condensing Water Boiler SERVICE TECHNICIAN S TROUBLE SHOOTING GUIDE 2004-28 TSG-SOLO-9/04 Table of Contents INTRODUCTION Page 1 SERVICING TIPS AND INSTRUCTIONS Page 3 CONTROL MODULE DISPLAY -

More information

Troubleshooting Guide For FG3000 Dual Medium Intensity Lighting System

Troubleshooting Guide For FG3000 Dual Medium Intensity Lighting System Troubleshooting Guide For FG3000 Dual Medium Intensity Lighting System TABLE OF CONTENTS SECTION 1.0 - GENERAL INFORMATION...1 1.1 Scope...1 1.2 General Description...1 1.3 Safety Precautions...2 1.4 Honeywell

More information

CHAPTER 20 SERVICE EQUIPMENT

CHAPTER 20 SERVICE EQUIPMENT SERVICE EQUIPMENT CHAPTER 20 SERVICE EQUIPMENT Service equipment includes service cabinets and the equipment and materials necessary for installation. 20.1 Signal Service Cabinet For MnDOT traffic control

More information

Series. Access Power Controllers. Installation Guide

Series. Access Power Controllers. Installation Guide Series Access Power Controllers Installation Guide Models Include: Maxim11 - Power Supply 1: 12VDC @ 3.5 amp or 24VDC @ 2.7 amp. - Power Supply 2: 12VDC @ 3.5 amp or 24VDC @ 2.7 amp. - Sixteen (16) fuse

More information

CAUTION WARNING. 50T Integrated Furnace Control INSTALLATION INSTRUCTIONS DESCRIPTION PRECAUTIONS

CAUTION WARNING. 50T Integrated Furnace Control INSTALLATION INSTRUCTIONS DESCRIPTION PRECAUTIONS 50T35-743 Integrated Furnace Control INSTALLATION INSTRUCTIONS FAILURE TO READ AND FOLLOW ALL INSTRUCTIONS CAREFULLY BEFORE INSTALLING OR OPERATING THIS CONTROL COULD CAUSE PERSONAL INJURY AND/OR PROPERTY

More information

TT /97. Features INSTALLATION INSTRUCTIONS. Horn. Lamps

TT /97. Features INSTALLATION INSTRUCTIONS. Horn. Lamps TT-1023 1/97 INSTALLATION INSTRUCTIONS Original Issue Date: 2/94 Model: 6-2000 kw Market: Industrial Subject: Flush- or Surface-Mount Remote Annunciator Kits PA-293991 and PA-293991-SD The remote annunciator

More information

ISIMET Series Shop Controller

ISIMET Series Shop Controller ISIMET 5000 6000 Series Shop Controller Installation, Maintenance, Operations, and Start-up Instructions The 5000 / 6000 Series Shop Controllers can be utilized to control multiple utility services, gas

More information

EB-M*-** Midsize Electro-Boiler BL509. EB-S-**/EB-WX-**-2 TS Standard Electro-Boiler BL506. EB-CX-** TS Commercial Electro-Boiler BL508

EB-M*-** Midsize Electro-Boiler BL509. EB-S-**/EB-WX-**-2 TS Standard Electro-Boiler BL506. EB-CX-** TS Commercial Electro-Boiler BL508 Electro-HELPS IX Boiler, Submittal Data Sheets These provide the mechanical technical details often required for architects/design engineers, shop drawings, etc. They are also useful in providing additional

More information

OPERATING AND MAINTENANCE MANUAL FOR ELECTRIC STAINLESS STEEL HEATER FOR DEIONIZED (DI) WATER ELECTRIC HEATER COMPANY BASE MODEL D

OPERATING AND MAINTENANCE MANUAL FOR ELECTRIC STAINLESS STEEL HEATER FOR DEIONIZED (DI) WATER ELECTRIC HEATER COMPANY BASE MODEL D OPERATING AND MAINTENANCE MANUAL FOR ELECTRIC STAINLESS STEEL HEATER FOR DEIONIZED (DI) WATER ELECTRIC HEATER COMPANY BASE MODEL D HUBBELL ELECTRIC HEATER COMPANY P.O. BOX 288 STRATFORD, CT 06615 PHONE:

More information

Service Handbook. Servicing should only be performed by a Qualified Service Agent.

Service Handbook. Servicing should only be performed by a Qualified Service Agent. Service Handbook COMMERCIAL ELECTRIC WATER HEATERS Technical Support and Parts: 800-456-9805 www.americanwaterheater.com MODELS STCE3-52/80/119 & ITCE3-52/80/119 INSTALLATION CONSIDERATIONS - PRE SERVICE

More information

SOLID STATE SECURITIES, INC. THE "SS90" SERIES RELEASE DEVICES MADE IN THE U.S.A. SS90-WPS MODEL A/B INSTALLATION MANUAL

SOLID STATE SECURITIES, INC. THE SS90 SERIES RELEASE DEVICES MADE IN THE U.S.A. SS90-WPS MODEL A/B INSTALLATION MANUAL S S S S S S LISTED L * PATENT PENDING S S 90 OLID TATE ECURITIES, INC SOLID STATE FAIL-SAFE UNIT U 99Y9 RESET RELEASING DEVICE SOLID STATE SECURITIES, INC. THE "SS90" SERIES RELEASE DEVICES MADE IN THE

More information

INSTRUCTION MANUAL Portable Refrigerator Units MODEL 15-LITER Including the Standard Battery Backup System (BBS)

INSTRUCTION MANUAL Portable Refrigerator Units MODEL 15-LITER Including the Standard Battery Backup System (BBS) 1 INSTRUCTION MANUAL Portable Refrigerator Units MODEL 15-LITER Including the Standard Battery Backup System (BBS) SECTION TITLE PAGES 1 Introduction and Basic Operation 2-3 2 Cleaning & Storing 4 3 Basic

More information

MS-4012/4024 and CMS-4012/4024. Instruction Manual for the. Fire Alarm Control Panels

MS-4012/4024 and CMS-4012/4024. Instruction Manual for the. Fire Alarm Control Panels R 12 Clintonville Road, Northford, CT 06472 Phone: (203) 484-7161 FAX: (203) 484-7118 Instruction Manual for the MS-4012/4024 and CMS-4012/4024 Fire Alarm Control Panels Document 15586 5/11/93 Revision:

More information

INSTALLATION, OPERATION AND MAINTENANCE MANUAL

INSTALLATION, OPERATION AND MAINTENANCE MANUAL GE Digital Energy Power Quality INSTALLATION, OPERATION AND MAINTENANCE MANUAL GE TRANQUELL Enhanced Thermal Protection (ETP) Series Integrally Mounted Medium and High Exposure Surge Protective Devices

More information

OWNER S MANUAL. Vintage Signature Series models: AC750, AC1050, AC1100, AC1250, AC1500, AC1750. Proudly Made in the USA.

OWNER S MANUAL. Vintage Signature Series models: AC750, AC1050, AC1100, AC1250, AC1500, AC1750. Proudly Made in the USA. OWNER S MANUAL Vintage Signature Series models: AC750, AC1050, AC1100, AC1250, AC1500, AC1750 Proudly Made in the USA support@aquacomfort.com 888-475-7443 Manufacturing High Quality, High Efficiency Heat

More information

Installation Instructions

Installation Instructions Electric Heaters 5 --- 20 kw SMALL PACKAGED PRODUCTS (SPP) Accessory Electric Heaters For 13 SEER, R---410A, Z Chassis Installation Instructions NOTE: Read the entire instruction manual before starting

More information

ACCURATE ELECTRONICS INC

ACCURATE ELECTRONICS INC ACCURATE ELECTRONICS INC Page 1 of 7 Model 108078 2 Sept 09 WWW.ACCURATE.ORG PO BOX 1654 97075-1654 8687 SW Hall Blvd 97008 BEAVERTON OR USA 503.641.0118 FAX 503.646.3903 Practice Section 108078 Rev A

More information

Firefly II Multi Voltage RELEASE DEVICES. Firefly II & IIB-MV INSTALLATION MANUAL

Firefly II Multi Voltage RELEASE DEVICES. Firefly II & IIB-MV INSTALLATION MANUAL Firefly II Multi Voltage RELEASE DEVICES Firefly II & IIB-MV INSTALLATION MANUAL GENERAL DESCRIPTION: S/N The The Cookson Company Firefly II-MV time delay release devices are designed for use on rolling

More information

Wiring Instructions for the 2900 Series FIREGUARD Combination Door Closer-Holder and Releasing Device with Integral Smoke Detector

Wiring Instructions for the 2900 Series FIREGUARD Combination Door Closer-Holder and Releasing Device with Integral Smoke Detector Wiring Instructions for the 900 Series FIREGUARD Combination Door Closer-Holder and Releasing Device with Integral Smoke Detector CAUTION: FAILURE TO INSTALL OR ADJUST PROPERLY MAY RESULT IN INJURY OR

More information

ADDITIONAL INFORMATION

ADDITIONAL INFORMATION MODEL APS-3C AUTOMATIC SNOW/ICE MELTING SYSTEM CONTROL PANEL MODEL APS-4C AUTOMATIC SNOW/ICE MELTING SYSTEM CONTROL PANEL MODEL SC-40C MODULAR SNOW/ICE HEATER CONTROL SYSTEM SAFETY This device provides

More information

User s Manual. TIGER S EYE E-Series Mark V Jockey. TIGERFLOW Systems, Inc Mint Way Dallas, Texas

User s Manual. TIGER S EYE E-Series Mark V Jockey. TIGERFLOW Systems, Inc Mint Way Dallas, Texas User s Manual TIGER S EYE E-Series Mark V Jockey TIGERFLOW Systems, Inc. 4034 Mint Way Dallas, Texas 75237 214-337-8780 www.tigerflow.com TABLE OF CONTENTS Introduction... 4 Sequence of Operation... 5

More information

Instruction Manual Model L2 RF Switch

Instruction Manual Model L2 RF Switch Instruction Manual Model 1582-22L2 RF Switch November 2015, Rev. A CH1 AUTO CH2 SWITCH 1 2 1 2 STATUS 1 2 MODEL 1582 SWITCH CROSS TECHNOLOGIES INC. CH1 ONLINE MANUAL SELECT CH2 SWITCH MANUAL REMOTE ONLINE

More information

STATUS ALARM ALARM HISTORY POWER HISTORY RESET

STATUS ALARM ALARM HISTORY POWER HISTORY RESET Instruction Manual Model 1582-152 RF Protection Switch November 2009, Rev B. CH1 AUTO CH2 SWITCH 1 2 1 2 STATUS 1 2 MODEL 1582 SWITCH CROSS TECHNOLOGIES INC. CH1 ONLINE MANUAL SELECT CH2 SWITCH MANUAL

More information

MAINTENANCE & TROUBLESHOOTING GUIDE LEAK ALARM CHANNEL DRY OIL WATER AUX ALARM HIGH LOW CRITICAL WATER TANK LEVEL ALARM MODEL LDE-740 ADVANCE PAPER

MAINTENANCE & TROUBLESHOOTING GUIDE LEAK ALARM CHANNEL DRY OIL WATER AUX ALARM HIGH LOW CRITICAL WATER TANK LEVEL ALARM MODEL LDE-740 ADVANCE PAPER PNEUMERCATOR Liquid Level Control Systems Electronic Systems Excluding LC2000 And TMS Series MAINTENANCE & TROUBLESHOOTING GUIDE 400 300 500 FUEL LEVEL LEAK MONITOR 1 200 600 OIL/GAS NORMAL WATER PNEUMERCATOR

More information

Installation Guide for models:

Installation Guide for models: 140 58th St. Brooklyn, NY Access Power Controllers with Power Supplies Installation Guide for models: Maximal3FD - 12VDC @ 4.6 amp or 24VDC @ 5.2 amp. - Sixteen (16) PTC protected power-limited outputs.

More information

Beacon 410A Gas Monitor Operator s Manual

Beacon 410A Gas Monitor Operator s Manual Beacon 410A Gas Monitor Operator s Manual Part Number: 71-0397 Revision: F Released: 12/5/17 www.rkiinstruments.com Product Warranty RKI Instruments, Inc., warrants gas alarm equipment sold by us to be

More information

INSTALLATION INSTRUCTIONS AND OWNER S MANUAL FOR

INSTALLATION INSTRUCTIONS AND OWNER S MANUAL FOR INSTALLATION INSTRUCTIONS AND OWNER S MANUAL FOR ELECTRIC ON-DEMAND TANKLESS WATER HEATERS: SpecAdvantage with PhD Technology SafeAdvantage with PhD Technology 208 and 480 VAC three phase 32 144 kw 600

More information

CER Series 2. Installation Instructions. Electric-Hydronic Boilers. Installer

CER Series 2. Installation Instructions. Electric-Hydronic Boilers. Installer CER Series 2 Electric-Hydronic Boilers Installation Instructions Installer Read all instructions before installing. Follow all instructions in proper order to prevent personal injury or death. Consider

More information

PART GENERAL 1.01 SECTION INCLUDES

PART GENERAL 1.01 SECTION INCLUDES Specification Number: 26 24 16.06 Product Name: Emergency Lighting Control NQ Circuit Panelboards: 240 Vac, 48 Vdc Maximum SECTION 26 24 16.06 Emergency Lighting Control NQ Circuit Panelboards: 240 Vac,

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS T CLASS TSA Series 6 to 20 Ton AIR CONDITIONERS 6 20 TONS 506147 01 06/11 Supersedes 3/11 Litho U.S.A. RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE IMPORTANT The Clean Air Act

More information

Installation Instructions

Installation Instructions Electric Heaters 5 --- 20 kw SMALL PACKAGED PRODUCTS (SPP) Accessory Electric Heaters For 13 SEER, R---410A Manufactured Home Installation Instructions NOTE: The Dual Point Kit can only be installed on

More information

INSTRUCTION MANUAL. AlarmGard Chain Operator (Model FCA) AlarmGard Crank Operator (Model FKA)

INSTRUCTION MANUAL. AlarmGard Chain Operator (Model FCA) AlarmGard Crank Operator (Model FKA) INSTRUCTION MANUAL AlarmGard Chain Operator (Model FCA) & AlarmGard Crank Operator (Model FKA) WARNING 1. CAUTION: Review all installation instructions, procedures, cautions and warnings contained within

More information

WATLOW IND. WATROD Modular Duct Heater Installation & Maintenance Manual I&M NUMBER: Page: 1 Date:6/11/2008 Rev: 2

WATLOW IND. WATROD Modular Duct Heater Installation & Maintenance Manual I&M NUMBER: Page: 1 Date:6/11/2008 Rev: 2 I&M NUMBER: 316-42-15-1 Page: 1 _ Pre Installation Check to make sure that heater received is the same as that ordered. Elements may come in contact with each other during shipment. Minor adjustments to

More information

MANUAL RESET ALARM RELEASE BOX

MANUAL RESET ALARM RELEASE BOX MANUAL RESET ALARM RELEASE BOX (For 100~240VAC or 24VAC or 24VDC) INSTRUCTION MANUAL WARNING 1. CAUTION: Review all installation instructions, procedures, cautions and warnings contained within this manual

More information

MANUAL RESET ALARM RELEASE

MANUAL RESET ALARM RELEASE Fire Door Release MODEL AR-D2 MANUAL RESET ALARM RELEASE INSTRUCTION MANUAL AR-D2 GENERAL INFORMATION 1. Review all installation instructions, procedures, cautions and warnings contained within this manual

More information

Gunite & Fiberglass Pools

Gunite & Fiberglass Pools Electrical Wiring The Pro Logic Control Center and PS-16 Expansion Unit require both high and low voltage connections. Low voltage connections will be made to actuators, sensors, remote keypad, etc. High

More information

IF79 CAUTION CONTENTS YOUR THERMOSTAT REPLACES 1 PREPARATIONS. Installation Instructions for. Heating & Air Conditioning

IF79 CAUTION CONTENTS YOUR THERMOSTAT REPLACES 1 PREPARATIONS. Installation Instructions for. Heating & Air Conditioning CONTENTS Installation Instructions for Heating & Air Conditioning IF79 n- Programmable Heat Pump Thermostat Preparations... 1 Thermostat Details... 1 Removing Old Thermostat... 1-2 Mounting and Wiring...

More information

GasScanner 8C. Eight Channel Monitor. Operator s Manual. MINT-0281-XX Rev. A 01/29/08

GasScanner 8C. Eight Channel Monitor. Operator s Manual. MINT-0281-XX Rev. A 01/29/08 GasScanner 8C Eight Channel Monitor Operator s Manual MINT-0281-XX Rev. A 01/29/08 Product Warranty Matheson Tri-Gas, Inc., warrants gas alarm equipment sold by us to be free from defects in materials,

More information

Electrical Installation Instructions

Electrical Installation Instructions Steambath Generators Models: SM-2 and SM-5! Electrical Installation Instructions C US LISTED 995C WARNING: Elderly persons, pregnant women, or those suffering from heart disease, high blood pressure, diabetes,

More information

THE "SS90" SERIES RELEASE DEVICES MADE IN THE U.S.A. MODELS A/B INSTALLATION MANUAL

THE SS90 SERIES RELEASE DEVICES MADE IN THE U.S.A. MODELS A/B INSTALLATION MANUAL S S S S S S OLID TATE ECURITIES, INC S S 90 SOLID STATE FAIL-SAFE UNIT * PATENT PENDING LISTED 99Y9 RESET U L RELEASING DEVICE SOLID STATE SECURITIES, INC. THE "SS90" SERIES RELEASE DEVICES MADE IN THE

More information