EXHAUST FANS: LARGEST MOTOR x0.25=5hp x0.25 AT 100% = 1.25 KW 3.7KW AT 100%= 3.7 KW 3 HP AT 100%= 3.0 KW TOTAL A/C LOADS=26.5 HP AT 100% = 26.

Size: px

Start display at page:

Download "EXHAUST FANS: LARGEST MOTOR x0.25=5hp x0.25 AT 100% = 1.25 KW 3.7KW AT 100%= 3.7 KW 3 HP AT 100%= 3.0 KW TOTAL A/C LOADS=26.5 HP AT 100% = 26."

Leon O’Neal’
5 years ago
Views:

1 4#600 KCMIL, 1/0 IN 4" PVC & 1-4" PVC SPARE BELOW RADE ENCASED IN BAR SEE DETAIL /E-5. 60/3 0 TVSS 3#2/0, #6. 1 1/2"C. 175/3 1 L1A /3 15/3 100A/3P CIRCUIT BREAKER ELECTRICAL ONE LINE DIARAM - NEW 30KW-480Y/277V AT 0.8 PF, NATURAL AS EN SET IN A WEATHERPROOF HOUSIN WITH CRITICAL MUFFLER- REFER TO DETAIL /E-5 AND /E5. #1/0, 3/4"C. XFMR "TR-L1A" 480:120/208V, 112.5KVA K-13 (2) 3#3/0, 2#3/0 (N), #3 (), #3 (I), IN 2 1/2"C. L2A 15/3 15/3 15/3 15/3 20/3 20/3 15/3 15/3 15/3 15/3 100/3 70/3 60/3 30/3 20/3 VFD AHU-1 VFD AHU-2 VFD AHU-3 VFD VFD VFD VFD HWP-1 HWP-2 CHWP-1 CHWP-2 3#12, #12. 3/4"C. AHU-4 AHU-5 AHU-6 AHU-7 ELEVATOR ELEVATOR CONTROLLER 3P/70A ELEVATOR SHUNT TRIP FUSED SAFETY SWITCH WITH 60 A FUSE, FOR ELEVATOR SIZE OF FUSES TO BE COORDINATED WITH ELEVATOR MANUFACTURER 3#12, #12. 3/4"C. 3#12, #12. 3/4"C. RADIAL 12, /277V DELTA:WYE ED 300KVA, Z=5.75% EXISTIN MANHOLE & VACUUM SWITCH METER 2-4" PVC ENCASED IN (ONE SPARE), 1 SET 3#2, 15KV 400/3 ATS N E HE1 C LE1 H1A 30 3#4, #8 IN 1"C. 4#3, #8 IN 1 1/4"C. 4#3, #8. 1 1/4"C. 4#3, #8. 1 1/4"C. PRAIRIE VIEW A&M UNIVERSITY 3#2, #8. 4" PVC ENCASED IN JOCKEY PUMP DISC. SW. 30/15AF/3P JOCKEY PUMP CONTROLLER JP-1 5 HP, 480V, 3PH. (VERIFY) 5 4#10, #10. 3/4"C. 10 FT. MAXIMUM FIRE PUMP CONTROLLER FURNISHED AND INSTALLED BY FIRE PROTECTION CONTRACTOR- VERIFY PUMP SIZE PRIOR TO INSTALLATION. 50 JBOX FP-1 50 HP, 480V, 3PH. (VERIFY) 3#2, #8. 1 1/4" C. SIZE PER NEC ELECTRICAL LOAD ANALYSIS- PVAMU-12,2 SF 277/480V, 3 PHASE, 4 S, WYE LIHTIN: 12,2 SF x 3.5 W/SF x1.25 = KW 100A, 4 POLE AUTOMATIC TRANSFER SWITCH (ATS), 480V WITH ENINE STARTIN CONTACTS RECEPTACLES: NORMAL 1 W/SF x 22,2 SF= 22,2KW 1ST. = 10 KW REMAIN 12,2 x 50%= 6.1 KW TECHNOLOY 1 W/SF x 22,2 SF= 22,2KW 1ST. = 10 KW REMAIN 12,2 x 50%= 6.1 KW ELEVATOR: 25 HP = 30 KW (2) 3#3/0, 2#3/0 (N), #3 (), #3 (I), IN 2 1/2"C. MISC. LAB EQUIPMENT LOADS: 50 KW AT 65%= 32.5 KW PUMP LOADS 16 HP AT 100%= 16 KW EXHAUST FANS: HP AT 100%= 3.5 KW COND. UNITS: 3 HP AT 100%= 3.0 KW UNIT HEATER: 3.7KW AT 100%= 3.7 KW SERVICE ENTRANCE HVAC: TOTAL A/C LOADS=26.5 HP AT 100% = 26.5 KW LAREST MOTOR x0.25=5hp x0.25 AT 100% = 1.25 KW 2.1 KW / 480 ( 3 ) = 243 A ALTERNATE #1 REPLACE 30KW ENERATOR WITH A 250KW, 480Y277V ENERATOR, 400A, 4P0LE AUTOMATIC TRANSFER SWITCH, 400A/3P DISCONNECT SWITCH AND FEEDER. UNDER THIS ALTERNATE, THE ENERATOR WILL BE CAPABLE OF POWERIN THE WHOLE BUILDIN DURIN POWER OUTAE. SPARE SPARE SPARE 4#3, # /4" PVC ENCASED IN #8, 1/2"C. 3#3, 2#3N, #8.#8I 1"C. 3#10, #10.-3/4"C. 3#6, #10. 3/4"C. 3#3, 2#3N, #8.#8I 1"C. XFMR "TR-LE1" 480:120/208V, 30KVA, K-13 LE2 4#8, #10.- 3/4"C. UPS LE3 8KW UPS 120/208V, 4#6, #8.- 1"C. ALL "VFDs" PROVIDED BY MECHANICAL CONTRACTOR INSTALLED BY ELECTRICAL CONTRACTOR 3#12, #12.-3/4"C. FCU-1 #8, 1/2"C. XFMR "AUTOCLAVE" 480V DETA:240V DELTA, SEE /E3 3#10, #10.-3/4"C. SPECIAL RECEPTACLE "L15-30 FOR "AUTOCLAVE" LOCATED AT ROOM#204, SEE SHEET E-2 FOR EXACT LOCATION BUILDIN EXTERIOR BUILDIN INTERIOR 'DP' #3/0 MAIN BONDIN JUMPER #1/0 EQUIPMENT BONDIN JUMPER REEN BUILDIN STRUCTURAL STEEL COL. #1/0 ED CONDUCTOR (NEUTRAL) PER NEC WATER PIPE BAR 1 FOR SINLE POINT IN #1/0, 3/4"C SUPPLEMENTARY ROD(S) SYSTEM DIARAM #1/0, 3/4"C

2 RADIAL 12, /277V DELTA:WYE ED 300KVA, Z=5.75% 4#600 KCMIL, 1/0 IN 4" PVC & 1-4" PVC SPARE BELOW RADE ENCASED IN ROOF TO EXISTIN VAULT SWITCH METER ALTERNATE #1 250KW-480Y/277V AT 0.8 PF, EN SET IN A WEATHERPROOF HOUSIN 400A 4#600 KCMIL, 1/0 IN 4" PVC IN ENCASED SIZE PER NEC BAR SEE DETAIL /E5. E L N SERVICE ENTRANCE MAIN DISCONNECT SWITCH, 400A/400AF/3P WITH NEUTRAL, 277/480V - SE RATED 400A, 4POLE, 480V ATS - WITH ENINE STARTIN CONTACTS CIRCUIT BREAKER SECOND LEVEL L TVSS E N DP METER ENERATOR ALTERNATE #1 : 4#600 KCMIL, #3. IN 4" 1. ELIMINATE 100A 4 POLE "ATS" AND CONNECT PANEL "HE" DIRECTLY TO PANEL "DP". FIRST LEVEL 2. INCREASE SIZE OF ENERATOR SO ALL POWER BACKED UP BY ENERATOR. TO PANEL "DP" TO EXISTIN VAULT SWITCH PARTIAL ELECTRICAL ONE LINE DIARAM - ALTERNATE #1 PARTIAL ELECTRICAL RISER DIARAM - ALTERNATE #1 FIRE PUMP CONTROLLER- REFER TO SHEETS /E-4 AND /E-4 "TR-L1A" 480:120/208V, 112.5KVA PANEL "L1A", 120/208V 3PH., 4, 225A 400A/400AF/3P DISCONNECT SWITCH (SE RATED) 400A/4P AUTOMATIC TRANSFER SWITCH PANEL "LE1", 208Y/120V 3PH., 4, 100A MCB PANEL "HE1", 480Y/277V 3PH., 4, 100A MCB 3-4" SLEEVES THROUH WALL CAP FOR FUTURE USE ATS SUSPENDED "TR-LE1" 480:120/208V, 30KVA METER SEE ELECTRICAL RISER DIARAM /E4 PANEL "DP", 480Y/277V 3PH., 4, 400A MCB PANEL "H1A", 480Y/277V 3PH., 4, 100A MLO 42.5"Wx104.8Lx62.1H ENERATOR 300KVA HOUSEKEEPIN PAD SEE STRUCTURAL DW. COORDINATE DUCKBANK WITH AS, STEAM HOTWATER PIPIN TO BUILDIN HOUSEKEEPIN PAD SEE STRUCTURAL DW. REFER TO ELECTRICAL RISER DIARAM FOR ENERATOR FEEDER SIZE AND DETAIL /E-5 FOR ADDITIONAL BRANCH CIRCUITS FOR ENERATOR AND DETAIL /E-5 FOR ENERATOR IN UTILITY EASEMENT ENLARED MAIN ELECTRICAL ROOM - FIRST LEVEL (ALTERNATE #1) SCALE: 1/4" = 1'-0" TRUE NORTH PLAN NORTH AUTOMATIC TRANSFER SWITCH (ATS) SERVICE ENTRANCE DISC. SWITCH.

3 TELEPHONE DATA ENERAL NOTES: 1. REFER TO FLOOR PLANS E2 AND E2 FOR LOCATIONS AND QUANTITIES OF JACKS. 2. PROVIDE NYLON BUSHINS IN BOTH ENDS OF ALL CONDUITS. 3. PROVIDE PULL STRIN IN EACH CONDUIT. 4. ALL DATA/VOICE DROPS SHALL O TO IDF ROOM. 5. ROUTE EACH DATA/VOICE CABLES VIA CABLE BASKET LOCATED IN 1ST. FLOOR. 6. PROVIDE 3/4" PLYWOOD BACKBOARDS ON ALL WALLS OF NEW IDF ROOM. 7. ALL CONDUIT SLEEVES SHALL BE FIRE RATED. TELEPHONE/DATA SYSTEM RISER DIARAM KEYED NOTES: T1 2-4" CONDUIT TO COMMUNICATION MANHOLE. T2 TELEPHONE IN SYSTEM. T3 STUB-IN 1" C. WITH CABLE FROM EACH DATA/TELE OUTLET INTO 1ST. FLOOR AND RUN TO CABLE BASKET IN 1ST. FLOOR. SEE E-2 FOR CABLE BASKET LOCATION, CORE 2ND FLOOR WHERE REQUIRED. T4 FOR DATA/TELE OUTLET ON 2ND FLOOR WHERE SHOWN EXPOSED ON AN EXISTIN WALL, MOUNT IN 3/4" RS CONDUIT THRU FLOOR WITH J-BOX ANCHORED TO WALL. DATA OUTLET TELEPHONE TEL/DATA OUTLET 12" CABLE BASKET TRAY IN 1ST. FLOOR T4 CORE AS REQUIRED T3 T3 T3 3/4"C. W/ 3/4"C. W/ DATA T3 T3 T3 TTB IDF T2 IDF ROOM DATA OUTLET TELEPHONE OUTLET TELE/DATA OUTLET T1 TELEPHONE/DATA SYSTEM RISER DIARAM 16A PLENUM RATED CABLE ROOF MOUNTED ANTENNA (TO BE MOUNTED AS CLOSE AS POSSIBLE TO CENTER OF THE BUILDIN) A PS RECEIVER (TO BE MOUNTED AWAY FROM ANY OTHER TRANSMITTER OR RECEIVER TO OTHER CLOCKS IN 2ND LEVEL TO OTHER CLOCKS IN 1ST LEVEL ROOF DUPLEX RECEPTACLE COAX IN 3/4"C. PER MANUFACTURER RECOMMENDATION A PAIRS TWISTED SHIELD IN 3/4"C. PER MANUFACTURER RECOMMENDATION LE1-1 A PS TONE ENERATOR PS RECEIVER /TRANSMITTER TO 120VAC OUTLET LE1-3 TO PAIN SYSTEM TO 120VAC OUTLET TYPICAL LESS MASTER CLOCK SYSTEM RISER DIARAM 2ND FLOOR TO BRANCH CIRCUIT PANEL TELEPHONE WOOD BACKBOARD 4'WX8'HX3/4" PLYWOOD. PAINT WITH COATS OF FIRE RETARDANT WHITE PAINT. 120V CKT, LE1-3 MOUNT RECEPTACLE DIRECTLY TO TELEPHONE BOARD CARD READER CR WITH PULL STRIN 2 COMPARTMENT MOLD, SEE DETAIL /E-5 MOUNT RECEPTACLE DIRECTLY TO TELEPHONE BOARD TERMINATE CONDUIT WITH INSULATED BUSHIN 2-4" CONDUITS WITH PULLSTRIN TO NEAREST COMMUNICATION MANHOLE, BAR TELE/DATA OUTLET IN KNEE SPACE 2ND FLOOR 1#6 TO NEAREST BUILDIN STRUCTURE 06 TELEPHONE BOARD RISER DIARAM (LOCATED IN IDF ROOM 105D) 2 COMPARTMENT MOLD, SEE DETAIL /E-5 J-BOX ABOVE, SIZE PER MANUFACTURER RECOMMENDATION. CR TELE/DATA OUTLET IN KNEE SPACE CASEWORK TOP WITH CHASE BEHIND KNEE SPACE CABLE SECOND FLOOR CARD READER DOOR LOCK/STRIKE VERIFY LOCATION 1ST. FLOOR CABLE- SEE SPECIFICATIONS CARD READER SINLE AN FLUSH BOX AT 48" A.F.F. 2ND. FLOOR PROVIDE POWER AS NEEDED FROM PANEL LE2 FIRST FLOOR 05 SECOND LEVEL DOOR ACCESS CARD READER DETAIL ELECTRICAL CONTRACTOR TO INCLUDE IN HIS BID ROUH-IN RACEWAY THROUHOUT THE DRAWINS 1" CONDUIT WITH PULL STRIN (TYPICAL) TO CAMERAS 1" CONDUIT WITH PULL STRIN (TYPICAL) CABLE- SEE SPECIFICATIONS CARD READER(S) TO IDF FOR REMOTE MONITORIN TO FIRE ALARM PANEL J-BOX ABOVE, SIZE PER MANUFACTURER RECOMMENDATION. 1" CONDUIT WITH PULL STRIN TO MAIN RECEPTIONIST DESK SECURITY PANEL IN IDF ROOM (CABLIN BY OWNER) 120V. SEE PANEL LE2 DOOR LOCK/STRIKE VERIFY LOCATION CARD READER SINLE AN FLUSH BOX AT 48" A.F.F. PROVIDE POWER AS NEEDED FROM LE1 1ST. FLOOR TYPICAL SECURITY CONTROL PANEL 04 FIRST LEVEL DOOR ACCESS CARD READER DETAIL ELECTRICAL CONTRACTOR TO INCLUDE IN HIS BID ROUH-IN RACEWAY THROUHOUT THE DRAWINS

4 MATCH LENTHS SHOWN ON DRAWINS. FIXTURES DESINATED AS "3", "6" AND "7" ARE SUESTED LENTHS OF THE "" FIXTURES. SEE ARCHITECTURAL REFLECTED PLAN FOR ACTUAL TOTAL LENTH OF FIXTURE. J-BOX TV OUTLET RUN 1" CONDUIT WITH PULL STRIN CONCEALED BELOW FLOOR TO A/V EQUIPMENT 7'-6" 05 LOBBY 1 TV OUUTLET & POWER OUTLET LAYOUT TYPICAL MOUNTIN HEIHTS THE CONTRACTOR SHALL COORDINATE THE MOUNTIN HEIHT OF ALL FIXTURES, DEVICES, AND OUTLETS WITH ARCHITECTURAL PLANS AND ELEVATIONS. SPECIAL MOUNTIN HEIHTS SHOWN ON THE PLANS SHALL TAKE PRECEDENCE OVER THOSE IVEN BELOW. ALL MOUNTIN HEIHTS ARE FROM FINISHED FLOOR TO CENTERLINE OF DEVICE, UNLESS OTHERWISE NOTED. LIHTIN FIXTURES INTERIOR WALL MOUNTED, SCONCE WALL MOUNTED, ABOVE MIRROR WALL MOUNTED, ABOVE DOOR 6'-6" 0'-8" ABOVE TOP OF MIRROR CENTER BETWEEN FRAME & WALL MOUNTED, ABOVE STAIR LANDIN 7'-0" EXTERIOR IN SOFFIT (SEE ACHITECTURAL DETAIL) WALL MOUNTED, BESIDE DOOR 6'-0" STEP MOUNTED (SEE ARCHITECTURAL DETAIL) WALL MOUNTED, NEAR RADE 8'-0" ABOVE RADE LEVEL WALL MOUNTED, NEAR ROOF 2'-6" BELOW PARAPET SWITCHES WALL SWITCHES AND DIMMERS MANUAL MOTOR STARTERS 3'-9" 3'-9" RECEPTACLES WALL ABOVE COUNTER WITHOUT BACKSPLASH 0'-8" ABOVE TOP OF COUNTER ABOVE COUNTER WITH BACKSPLASH 0'-4" ABOVE TOP OF BACKSPLASH FOR TELEVISION (SAME AS TV OUTLET) WALL HUN SINKS (FCI) 3'-6" CLOCK 1'-0" BELOW MULTIOUTLET RACEWAY WALL 3'-0" ABOVE COUNTER WITHOUT BACKSPLASH 0'-8" ABOVE TOP OF COUNTER ABOVE COUNTER WITH BACKSPLASH 0'-4" ABOVE TOP OF BACKSPLASH TELEPHONE DESK/TABLE WALL TELEPHONE PAY TELEPHONE ABOVE COUNTER WITHOUT BACKSPLASH 0'-8" ABOVE TOP OF COUNTER ABOVE COUNTER WITH BACKSPLASH 0'-4" ABOVE TOP OF BACKSPLASH PAY TELEPHONE, HANDICAPPED (SEE ARCHITECTURAL DETAIL) DATA OUTLETS ELECTRICAL EQUIPMENT WALL ABOVE COUNTER WITHOUT BACKSPLASH ABOVE COUNTER WITH BACKSPLASH SAFETY SWITCH MOTOR STARTER PANELBOARD COMMUNICATIONS CABINET 0'-8" ABOVE TOP OF COUNTER 0'-4" ABOVE TOP OF BACKSPLASH FEEDER CONDUITS TV CABLE OUTLET WALL ARMOIRES WALL BRACKET 0'-4" ABOVE SHELF FOR TV CENTERLINE OF BRACKET CONTROL/SECURITY DOOR ALARM PUSHBUTTON DOOR ACCESS KEYPAD FIRE ALARM MANUAL PULL CHIME, HORN AND/OR STROBE 6'-8" OR 0'-6" BELOW CCTV CAMERA 0'-6" BELOW LEVEL CCTV MONITOR - (WHICHEVER IS LOWER) SMOKE, HEAT DETECTORS CONTROL PANEL, ANNUNCIATOR MANETIC DOOR HOLDER 0'-8" DOWN FROM TOP OF DOOR FLEX FLEX VENT MONITOR WALL ABOVE COUNTER 0'-8" ABOVE TOP OF COUNTER WALL BRACKET CENTERLINE OF BRACKET SOFFIT (SEE ARCHITECTURAL DETAIL) VIBRATION MOUNTS NOTES: HOUSEKEEPIN PAD 1. MAINTAIN MINIMUM OF 6" DISTANCE FROM HORIZONTAL CONTSTRUCTION (WALLS, DUCTS, ETC.) AND 12" FROM ALL VERTICAL CONSTRUCTIONS (S, DUCTS, ETC.). FLOOR MOUNTIN 2. FLEXIBLE CONDUIT SHALL BE LENTH IN SPECIFICATIONS AND POSITIONED TO AVOID TRANSMISSION OF VIBRATION. HOT 3. VIBRATION ISOLATORS SHALL BE SUBMITTED FOR APPROVAL. NEUTRAL 04 MOUNTIN DETAIL HOT NEUTRAL DATA QUADRAPLEX (ORANE) NOTES: RESET TEST FCI DEVICE SUCH THAT THE DOWNSTREAM DEVICES ARE NOT AFFECTED BY FAULT INTERRUPTION. IE. NON FEED THRU. EACH FCI DEVICE SHALL BE SELF PROTECTIN ONLY. DEDICATED QUADRAPLEX (ORANE) 1. PROVIDE DEDICATED CIRCUIT FOR EACH QUAD OUTLET WITH DEDICATED IN 3/4" CONDUIT. 2. CORE DRILL SECOND FLOOR AS REQUIRED (MIN. 2-4" CORE) FOR DATA & POWER. 3. ALL CONDUITS IN FIRST LEVEL TO BE RUN TO ABOVE IN FIRST FLOOR ( ALL DATA/TELE CONDUITS TO NEAREST CABLE TRAY AND POWER CIRCUITS TO DESINATED PANEL). FCI RECEPTACLE WIRIN DIARAM ACCESS PANEL 4. ALL CONDUITS IN SECOND LEVEL TO BE RUN TO ABOVE IN FIRST FLOOR ( ALL DATA/TELE CONDUITS TO NEAREST CABLE TRAY AND POWER CIRCUITS TO DESINATED PANEL). STEEL CHANNEL SIZE AND LENTH AS REQUIRED, ANCHOR TO WALL DEDICATED QUADRAPLEX (ORANE) 4" 1" 4" REFERENCE ARCHITECTURAL DRAWIN /A-512 CONDUIT (TYPICAL) PIPE OR CONDUIT CLAMP CONDUIT SUPPORT WALL MOUNTED DETAIL TYPICAL DUPLEX DATA/TELEPHONE OUTLETS & QUAD ELECTRICAL OUTLETS FOR LAB VERRTICAL UTILITY CHASE

5 FLOOR J-BOX ABOVE ACCESSIBLE DRINKIN FOUNTAIN WITH FCI BLANK FACE LINE POWER INPUT FCI BLANK FACE INSTALLED OUTSIDE OF EWC TEST BUTTON RECEPTACLE MOUNTED WITHIN CONFINES OF DRINKIN FOUNTAIN1 RESET BUTTON ELECTRICAL WATER COOLER POWER DETAIL RADE SCHEDULED PARTITION NOTES BY SYMBOL: WARNIN TAPE SHALL RUN ENTIRE LENTH OF CABLE MIN. DEPTH FOR SECONDARY SERVICE. 24" MIN. DEPTH FOR PRIMARY SERVICE TO PAD MOUNTED 12" COMPACTED FILL MINIMUM 12" BETWEEN BOXES UNLESS OTHERWISE INDICATED CUT YPSUM BOARD TO ALLOW 1/4" MINIMUM OVERLAP BY FACE PLATE FLEXIBLE CONDUIT MINIMUM OF ONE STUD BETWEEN OUTLETS REFER TO NEC ARTICLE (A)(1)(a) THROUH (A)(1)(c) FOR DEPTH OF WORKIN SPACE FOR ELECTRICAL EQUIPMENT 600V OR LESS. REFER TO NEC ARTICLE (A)(2) FOR WIDTH OF WORKIN SPACE FOR ELECTRICAL EQUIPMENT 600V OR LESS. REFER TO NEC ARTICLE (A)(3) FOR HEIHT OF WORKIN SPACE FOR ELECTRICAL EQUIPMENT 600V OR LESS. REFER TO NEC ARTICLE (E)(1)(a) THROUH (E)(1)(d) FOR DEDICATED EQUIPMENT SPACE FOR ELECTRICAL EQUIPMENT 600V OR LESS. VARIES W/ CONDUIT SIZE. CONDUITS ( ENCASED) VARIES W/ CONDUIT SIZE. 05 SEAL VOIDS FROM OUTSIDE AND COVER BOX WITH 1/3" MINIMUM ACOUSTICAL SEALANT (TYPICAL) BACK TO BACK BOXES ARRANEMENT FOR NOISE CONTROL 04 PANEL TYPICAL PANELBOARD CLEARANCE DETAIL 1 3/4" SECURED TO WALL 4 3/4" LOCK WASHER 2" LOCK WASHER 5/8" HARDWARE EQUAL 2" 5/8" HARDWARE MOUNTIN BOLT LOCK WASHER INSULATOR FABRICATED FROM FLAME RESISTANT FIBERLASS-REINFORCED THERMOSET POLYSTER MOLDIN COMPOUND (TYPICAL OF BOTH SIDES) 2" LOCK WASHER EQUAL 5/8" HARDWARE HOLES DRILLED W/NUMBER & SIZE AS REQUIRED 2" DUPLEX RJ45 DATA OUTLET (TYP.) DUPLEX RECEPTACLE (TYP.), PROVIDE FCI TYPE IF THEY ARE WITHIN 6' OF SINK BAR (COPPER) 1/4" X 4" X LENTH COORDINATE EXACT LENTH WITH NUMBER OF CABLES CONNECTIN - MIN. 21" IN MAIN ELECTRICAL ROOM WALL MOUNTED SINLE- POINT BAR DETAIL MOLD ALDS 4000 (STAINLESS STEEL) DETAIL VARIES W/ CONDUIT SIZE. VARIES W/ CONDUIT SIZE. 200% NEUTRAL BUS I A B C N SERVICE RACEWAY 200% NEUTRAL BUS PANELBOARD BUS ISOLATED BUS EQUIPMENT IN CONDUCTOR (EC) I AB C N 200% NEUTRAL OR DEDICATED NEUTRAL FOR EACH PHASE 09 NON-LINEAR LOAD PANELBOARD DETAIL 06 TYPICAL DUCT BANK DETAIL 1" C. RECESSED J-BOX IN FURRED OUT WALL ENTRY FOR DATA FROM J-BOX ABOVE (OR AT STRUCTURE) 1" C. RECESSED J-BOX IN FURRED OUT WALL ENTRY FOR POWER FROM J-BOX ABOVE (OR AT STRUCTURE) MOLD S4000 SERIES DUAL CHANNEL BRUSHED STAINLESS STEEL RACEWAY WITH FCI DUPLEX RECEPTACLES AT 36" CENTERS ALTERNATIN WITH DUPLEX TELE/DATA OUTLETS IN BOTTOM CHANNEL. ALTERNATIN RECEPTACLES ON A CIRCUIT. MOLD S40D ENTRANCE END FITTIN, TO POWER START OR DATA CABLES. PROVIDE ONE AT EACH END OF RUN. 1. UTILIZE S4000 SERIES RACEWAY PARTS FOR ELBOW, DEVICE MOUNTIN PLATES, COVER PLATES, ETC. AS REQUIRED FOR COMPLETE WORKIN ASSEMBLIES. 2. MOLD FOR FIRST FLOOR SHOWN. 3. FOR MOLD ON SECOND FLOOR, CONDUIT IS RUN IN FIRST FLOOR SPACE AND ENTERS FROM BOTTOM OF ENTRANCE FITTIN.

6 ELEVATOR ENERAL NOTES: ELEVATOR KEYED NOTES: 1. 1 PROVIDE MOUNTED SMOKE DETECTOR IN THIS DETAIL DEPICTS TYPICAL ELEVATOR SITUATION AND IS NOT AN EXACT REPRESENTATION OF CONSTRUCTION. THIS DETAIL SHOULD BE USED FOR ELECTRICAL REQUIREMENTS, EQUIPMENT TYPES, CONNECTIONS AND OPERATION SEQUENCE. COORDINATE EXACT LOCATION OF ALL ELECTRICAL DEVICES WITH ELEVATOR MANUFACTURER AND ALL APPLICABLE CODE OFFICIALS PRIOR TO ROUH-IN. PROVIDE ALL ACCESSORIES NEEDED FOR A COMPLETE AND FUNCTIONIN SYSTEM. WIRIN AND CONTROLS SHALL BE IN ACCORDANCE WITH ALL APPLICABLE ELEVATOR REQUIREMENTS AND IN COMPLIANCE WITH THE ELEVATOR MANUFACTURER REQUIREMENTS AND ALL REQUIREMENTS OF THE LOCAL AUTHORITY HAVIN JURISDICTION. ALL ELECTRICAL DEVICES INSTALLED IN ELEVATOR PIT SHALL BE LISTED AND LABLED FOR WEATHERPROOF RATIN. PROVIDE TRAVELIN CABLE AS REQUIRED. IN THE EVENT OF POWER FAILURE ALL ELEVATOR EQUIPMENT REQUIRIN POWER SHALL OPERATE UNDER ONE OF THE FOLLOWIN CONDITIONS. a ELEVATOR MACHINE ROOM, HOISTWAY, AND AT EACH ELEVATOR LOBBY. SMOKE DETECTOR SHALL INTERFACE WITH ELEVATOR CONTROL PANEL. SMOKE DETECTORS LOCATED IN ELEVATOR LOBBIES SHALL INTERFACE WITH THE FIRE ALARM CONTROL PANEL FOR ELEVATOR RECALL PURPOSES. PROVIDE VISUAL AND/OR AUDIO NOTIFICATION DEVICE IN EACH ELEVATOR LOBBY. REFER TO ELECTRICAL AND ARCHITECTURAL PLANS FOR EXACT LOCATIONS. PROVIDE FIREMAN'S PHONE OUTLET IN EACH ELEVATOR LOBBY. REFER TO ELECTRICAL AND ARCHITECTURAL PLANS FOR EXACT LOCATIONS. PROVIDE CIRCUIT AND MOTOR RATED SWITCH FOR EACH SUMP PUMP. SWITCH TO BE LOCATED ADJACENT TO ELEVATOR PIT ACCESS/LADDER. COORDINATE EXACT LOCATION AND REQUIREMENTS OF SUMP PUMP WITH PLUMBIN CONTRACTOR. PROVIDE LIHT SWITCH ADJACENT TO ELEVATOR PIT ACCESS. PROVIDE WALL MOUNTED FIXTURE. PROVIDE WEATHER PROOF, FCI DUPLEX RECEPTACLE FOR MAINTAINANCE. CIRCUIT WITH PIT LIHT PROVIDE TELEPHONE OUTLET WITH PULL STRIN PER ELEVATOR. COORDINATE EXACT LOCATION OF TELEPHONE WITH ELEVATOR SUPPLIER. PROVIDE DEDICATED TELEPHONE LINE FROM TELEPHONE COMPANY. PROVIDE 120V DEDICATED FCI CIRCUIT PER ELEVATOR TO LOCKABLE SWITCHES FOR ELEVATOR CAB LIHTIN. LOCATE SWITCHES IN ELEVATOR MACHINE ROOM. PROVIDE ENCLOSED SHUNT TRIP CIRCUIT BREAKER FEEDIN EACH ELEVATOR MOTOR/CONTROLLER. CIRCUIT BREAKER SHALL BE LOCKABLE IN THE 'OFF/OPEN' POSITION. CIRCUIT BREAKER SHALL BE ADJUSTABLE TIME DELAY TYPE, COORDINATE REQUIREMENTS WITH ELEVATOR MANUFACTURER. PROVIDE AUDIO/VISUAL NOTIFICATION DEVICE IN ELEVATOR MACHINE ROOM. REFER TO FIRE ALARM CONTRACTOR PLANS FOR EXACT LOCATIONS. PROVIDE LED SCENT LIHT FIXTURES. FIXTURES TO BE ON EMERENCY/BATTERY SERVICE. REFER TO ELECTRICAL LIHTIN PLANS FOR LOCATION AND CIRCUITIN. b. 8 PROVIDE /WALL MOUNTED HEAT DETECTOR IN ELEVATOR MACHINE ROOM, HOISTWAY, AND ELEVATOR PIT AT EVERY SPRINKLER HEAD, REFER TO FIRE PROTECTION OF RISE, REFER TO SPECIFICATIONS FOR REQUIREMENTS. HEAT DETECTORS SHALL BE D SO TO SHUNT TRIP THE MAIN POWER SUPPLY TO ELEVATOR AFTER THE CAB HAS RETURNED TO THE LOWEST LANDIN OF RECALL. HEAT DETECTORS SHALL INTERFACE WITH THE ELEVATOR CONTROL PANEL AND THE FIRE ALARM CONTROL PANEL. F4 TOP OF F4 HOISTWAY ROOF F HOISTWAY DP-15 LE ELEVATOR EQUIPMENT F ELEVATOR MACHINE ROOM 8 4 ELEVATOR PIT LE ELEVATOR MACHINE ROOM AND HOISTWAY DETAIL WP FCI NEMA-1 ENCLOSURE SIZE AS REQUIRED PHOTOCELL ON ROOF AIMED NORTH BY-PASS SWITCH 120V TIME CLOCK INTERMATIC DIITAL PRORAMMABLE 120V CONTROL CIRCUIT 277V LIHTIN CONTACTOR W/120V COIL NEUTRAL SEE PANEL SCHEDULES CIRCUITS TO ALL EXTERIOR LIHT FIXTURES- SEE SHEETS E-1 & E1 04 EXTERIOR LIHT CONTROL SCHEMATIC 100A, 4 POLE, AUTOMATIC TRANSFER SWITCH (ATS) WITH ENINE STARTIN CONTACTS H 30 KW WEATHERPROOF AS ENERATOR 480/277V, 3PH., 4W. N H N #8 TO DRIVEN ROD EQUIPMENT IN CONDUCTOR (TYP.) ED CIRCUIT CONDUCTOR (NEUTRA) (TYP.) 277V/480Y, 3 PHASE PANEL EMERENCY PANEL N N H TO NORMAL DISTRIBUTION PANE; (DP) IN DIARAM FOR EMERENCY ENERATOR EXTERIOR INTERIOR WEATHERPROOF ENERATOR ENERATOR CONTROL PANEL 100A ENCLOSED CIRCUIT BREAKER EMERENCY ENERATOR BATTERY CHARER BLOCK HEATER TO TRANSFER SWITCH SEE RISER DIARAM L1A-44 L1A-46 RUN 2#12 IN 3/4"C. TO ATS ENINE START CONTACTS RUN 1" CONDUIT WITH 14/2 SHIELDED CABLE TO CAMPUS FAS NETWORK IN IDF EMERENCY ENERATOR DETAIL 120V FIXTURE 120V FIXTURE ON LE1-2 3/4"C. REMOTE ENERATOR ANNUNCIATOR PANEL EMERENCY "OFF" SWITCH HE1-3 HE1-3 F4 F4 SEE DRAWIN E-2 FOR LOCATIONS 120V FIXTURE F4 FCI WP F4 120V FIXTURE

7 120V CIRCUITS FROM PANEL (SEE DRAWINS FOR QUANTITIES) MOUNT ABOVE, FIELD CONNECT CONTROL WIRIN ISIMET E-SERIES: E S-L-EX OR APPROVED EQUAL ELECTRICAL ENCLOSURE TO EXH. FAN CIRCUIT TO EACH SOLENOID & RELAY ENERAL NOTES: 1. INSTALL PER MANUFACTURER'S RECOMMENDATIONS AND INSTRUCTIONS. 2. COORDINATE WITH PLUMBIN SHEETS. 3. CONTROLLER SHALL BE PROVIDED WITH A DOOR PANEL MOUNTED MOMENTARY PANIC BUTTON ASSEMBLY. TO HOOD (RECEPTACLE) TO SCIENCE LAB RECEPTACLES HOT WATER COLD WATER AS ROOM EXHAUST FAN UTILITY CONTROLLER 120 VAC CONTROL WIRIN ISIMET UTILITY CONTROLLER: LA SERIES CONTROLLER WITH EPO SWITCH LA R FIRE ALARM PANEL 4. PROVIDE CONDUIT FOR CONTROL AND INTERATION WIRIN. 5. PROVIDE 20A, 120V DEDICATED CIRCUIT FOR UTILITY CONTROLLER. 6. PROVIDE 24VAC CONTROL WIRIN FROM UTILITY CONTROLLER TO EACH CONTROLLED UTILITY OR DEVICE. 7. UTILITY CONTROLLER WITH PUSH BUTTON EMERENCY SHUT-OFF AND MANUAL ON/OFF KEYED SWITCH. REMOTE EOP SWITCH WHERE REQUIRED FOR PREP. ROOM 8. ALL RECEPTACLES CIRCUITS IN THE SCIENCE LAB SHALL BE CONNECTED THROUH THE ISIMET CONTROLLER, EXCEPT FOR CIRCUIT DESINATED FOR REFRIERATOR OR FREEZER.. ISIMET S-SERIES: S ()- OR APPROVED EQUAL SOLENOID ENCLOSURE TO EACH SOLENOID & RELAY MOUNT ABOVE, FIELD CONNECT CONTROL WIRIN CONNECTION TO SINKS, FAUCETS AND AS TURRETS, (REFER TO PLUMBIN) FURNISH AUTOMATIC SHUTOFF OF WATER, AS, AND ELECTRICAL POWER IN SCIENCE LAB. UTILITY CONTROL PANEL SHALL BE SEMI-RECESSED AND SHALL HAVE EPO SWITCH. THE SWITCHES IN ALL LABS SHALL BE KEYED THE SAME, INCLUDIN STORAE CABINET. LOCATION OF UTILITY CONTROLLER SHALL BE APPROVED BY ARCHITECT AND OWNER PRIOR TO INSTALLATION. SEE PLUMBIN DRAWINS FOR INFORMATION ON SOLENOID VALVE ENCLOSURE. PROVIDE A SEPARATE ON-OFF SWITCH FOR ROOM EXHAUST FAN. RUN ALL POWER DUPLEX & QUAD RECEPTACLES CIRCUITS AND THE HOOD EXHAUST FAN CIRCUIT THROUH E-SERIES ELECTRICAL ENCLOSURE (ENCLOSURE CAN BE MOUNTED ABOVE ). DO NOT RUN LIHTIN CIRCUITS THROUH CONTACT AND DO NOT POWER CIRCUITS IN PREP ROOM THROUH CONTACTOR U.N.O. FOR LABORATORIES WITH UTILITY CONTROLLERS FOR EMERENCY SHUTDOWN OF AS, WATER, AND ELECTRICAL POWER, PROVIDE ADDRESSABLE CONNECTIONS SO THAT THE FIRE ALARM SYSTEM CAN CAUSE THE UTILITIES TO BE SHUTDOWN UNDER A FIRE ALARM CONDITION, AND SO THAT IF THE EMERENCY SHUTDOWN IS ACTIVATED IN THE LABORATORY, IT WILL CAUSE A TROUBLE ALARM TO SOUND AT THE FIRE ALARM PANEL. SEE PLUMBIN DRAWINS FOR SOLENOID VALVE SIZES. 9. ALL RECEPTACLES WITHIN 6 FT. OF SINK SHALL BE FCI TYPE AND CONNECTED THROUH THE ISIMET CONTROLLER. ISIMET CONTROLLER NOTES 1. ELECTRICAL CONTRACTOR: PROVIDE A UTILITY CONTROLLER (LA SERIES) AND E-SERIES CONTACTOR ENCLOSURE FOR EMERENCY SHUT-OFF OF POWER (RECEPTACLES), COLD WATER, HOT WATER AND AS. PROVIDE INDIVIDUAL CONTROL SWITCH FOR CW/HW//AS/RECEPTACLES AND ROOM EXHAUST FAN. CONTACTOR ENCLOSURES FOR ELECTRIC CIRCUITS TO BE MOUNTED ABOVE. ELECTRICAL CONTRACTOR TO FURNISH AND INSTALL UTILITY CONTROLLER AND E-SERIES CONTACTOR ENCLOSURE AND PROVIDE ALL 120 VOLT WIRIN AND 24V WIRIN BETWEEN CONTROLLER, CONTACTOR ENCLOSURE AND EQUIPMENT. PROVIDE CONTACTOR ENCLOSURES FOR ALL CIRCUITS (RECEPTACLES, DUPLEX, FAN). ELECTRICAL CONTRACTOR ALSO TO PROVIDE 24 VOLT CONTROL WIRIN BETWEEN UTILITY CONTROLLER AND S-SERIES SOLENOID ENCLOSURE. INNER CONNECT WITH FACP TO SHUT DOWN SERVICES. COORDINATE WITH FIRE ALARM CONTRACTOR. 2. PLUMBIN CONTRACTOR: PROVIDE PRE-ASSEMMBLED (S-SERIES) SOLENOID ENCLOSURE WITH ALL CONTACTS RESET SOLENOID AND INTERFACE RELAYS FOR SCIENCE ROOM FOR EMERENCY SHUT-OFF OF COLD WATER, HOT WATER AND AS. EACH SOLENOID TO BE ASSEMBLED WITH THREADED BALL VALVE, UNIONS, "Y" STRAINERS, SHOCK ARRESTOR, AND CAPPED ENDS FOR FIELD INSTALLATION. ENCLOSURE SHALL BE NEMA 1 ABOVE. 3. ELECTRICAL AND PLUMBIN CONTRACTOR TO COORDINATE ALL REQUIREMENTS TO PROVIDE COMPLETE AND WORKABLE SYSTEM. 4. PROVIDE FACTORY START-UP WITH PLUMBIN AND ELECTRICAL CONTRACTOR PRESENT AND SINED START-UP CERTIFICATE. 5. WHEN EMERENCY BUTTON IS DEPRESSED POWER IS SHUT OFF TO ALL AUXILIARY DEVICES IN THE LAB AND EXHAUST FAN IN THE LAB IS TURNED ON TO RUN. 6. PROVIDE 10 KEYS FOR EACH UTILIITY PANEL KEYED ALIKE FOR BOTH PANELS. TYPICAL SCIENCE LAB EMERENCY SHUT-OFF "ISIMET" SYSTEM DETAIL

8 PRAIRIE VIEW A&M UNIVERSITY

9 PRAIRIE VIEW A&M UNIVERSITY

FIRE ALARM: BY OTHERS, IF REQUIRED.

FIRE ALARM: BY OTHERS, IF REQUIRED. x x x x x x OS LIGHTING S FLUORESCENT LIGHT FIXTURE, SEE LIGHT FIXTURE SCHEDULE FOR SIZE AND MOUNTING. FLUORESCENT STRIP LIGHT FIXTURE, SEE LIGHT FIXTURE SCHEDULE FOR SIZE AND MOUNTING. WALL BRACKET FLUORESCENT