KIT IOM
|
|
- Elfrieda Marshall
- 5 years ago
- Views:
Transcription
1 KIT IOM Replacement Kit:
2 Table of Contents THE UPM CONTROLLER...3 SPECIFICATIONS...4 KIT INCLUDES...5 INSTALLATION PROCEDURE...5 Remove Old Board...5 Mounting holes...5 Wiring Installation...6 Sensor Installation...8 FINAL PROCEDURES
3 The UPM Controller The Unit Protection Module (UPM) board, shown in Figure 1, is used in all configure-toorder applications. The controller provides short cycling and refrigerant circuit protection. The controller is a plug and play device which also has options for freeze and condensate overflow protection if sensors are installed. The controller is programmed and it is backwards compatible for most functions of its earlier versions. This controller can be used as replacement for the following part numbers: User settings such as reset on power versus Y call and the number of faults prior to lockout among others can be adjusted by a qualified technician when replacing previous revisions. Figure 1 - UPM Controller 3
4 Specifications Power: Physical: Environmental Operating Range: 24VAC ± 10%, 50-60Hz, 1.4 VA of standby power consumption (Single Class II 70VA or 100VA option available) Printed Circuit Board and plastic stand offs. -40 to 176 F (-40 C to 80 C); 10 to 90% relative humidity, non-condensing All controls are conformal coated for environmental protection. Digital Outputs: Inputs: Two digital outputs relay contacts rated at 10A 125 VAC; One dedicated for the compressor contactor 24VAC when ON and one dedicated for alarm purposes dry contact Normally Open (NO) Four (4) inputs. Dedicated inputs for: High Pressure Switch (HPC) Low Pressure Switch (LPC) Freeze Sensor (FREEZE) 10 77F Thermistor Condensate Overflow Sensor (CON) 230 K +/- 15% Compressor Call (Y) Signal Status Indication: Protection: Visual (LED) status of power and alarms status indication. Surge and transient protection circuitry. Weight: Overall Dimensions: Listed By: 0.14 lbs. (0.07 Kg). 4-1/4 (width) by 3-3/4 (height) by 1-3/4 (recommended panel depth). 108mm (width) by 95mm (height) by 32mm (recommended panel depth). UL Mounting Hole Dimensions: Four mounting holes in rectangular pattern with dimensions between them as follows: 3-3/4 (width) by 3-1/4 (height). 95mm (width) by 83 mm (height). 4
5 Kit Includes The UPM replacement kit includes the following components required for the replacement from all previous board versions. Included in this kit Description Qty Screws 1" 4 UPM I Replacement Instructions 1 UPM I IOM 1 Nylon Tubular Sleeves 4 Unit Protection Module, UPM-I 1 Freeze sensor jumper Assembly 1 Ground harness Assembly 1 Needs to be updated Installation Procedure Controller shall be installed inside the unit electrical box; mounting holes are available on the location of the previous board. The plastic stand-offs from the UPM board match the pilot holes on the electrical box. Remove Old Board 1. Locate existing UPM in unit electrical box. 2. Verify old part number on the old board as one of the four listed on page Take a picture or LABEL all wires currently present and according to the terminal designations on the UPM board. 4. Disconnect all the previously labeled wires. 5. Remove existing circuit board. Mounting Holes If existing UPM has plastic stand-offs, pinch the tab on the stand-off from the top side and push downward to release it from the circuit board as shown in Figure 2. The snap the new board onto the stand-offs. If existing UPM does NOT have plastic stand-offs, choose one of the following: A. If drilling is possible bigger pilot holes will need to be made. 1. Use a unit bit or a 3/16 (0.187 ) drill bit to enlarge the existing pilot hole of the electrical box. 5
6 2. Align the plastic stand-offs with the new pilot holes and push in firmly until the stand-offs snap in and do not pull out. B. If drilling is not possible due to space constraints screws will be used to fasten the board. 1. Remove plastic stand-offs from the new controller. Pinch the tab on the stand-off from the top side and push downward to release it from the circuit board as shown in Figure Secure controller to unit by using four 1 long #6 screws along with the tubular sleeves. Wiring Installation Reconnect the wires using the labels or picture from old board removal process. IMPORTANT: Freeze Protection A. If the unit is not equipped with Freeze Protection, use the supplied jumper to short the FREEZE terminals. Open connections will result in faults and lockouts. B. If unit has an existing Freeze Protection or if it will be installed proceed to Sensor Installation section on page 8. Figure 2 - Plastic Stand-Off 6
7 CONTROLS IMPORTANT: Ground Do not forget to ground the board. If a connection is not available, ground the terminal by: 1. Adding a new screw to the electrical box. 2. Using an existing screw that secures an existing component. Avoid sharp edges on unit cabinet during installation Figure 3 - UPM Location 7
8 Sensor Installation If the unit is equipped with freeze sensor, it can be found attached to the leaving water pipe as shown in Figure 4. The new controller has a different trip point for sensing freeze condition, and therefore the freeze sensor must be relocated to the refrigerant line as shown in Figure 5. Figure 4 - Freeze Sensor's Previous Location, Older Versions Figure 5 - Freeze Sensor's New Location IMPORTANT: If unit is equipped with factory installed DDC, two sensors can be found. Make sure that the DDC leaving water sensor remains in place as it may cause nuisance alarms in the building automation system. Once the sensor has been relocated use wire ties and cork tape to secure and insulate sensor as shown below in Figure 6, Figure 7, and Figure 8. If this is a new install (no previous sensor) the wires must be led into the electrical box and connected to the UPM across the FREEZE connections as shown in Figure 9. 8
9 Figure 6 - Sensor with Wire Ties Figure 7 - Wire Tied Sensor with Cork Tape Figure 8 - Final Sensor Installation with Insulating Tape 9
10 Final Procedures 4 LOCKOUT RESET R Y 2 ALARM CONT PULSE 1 TEST YES NO 1. Check the blue dip switch with the white rockers. The table above shows the switch functionality. 2. If the STATUS LED is blinking, count the number of blinks in an interval. The number of blinks will indicate the fault. Figure 10 shows the operation flow and consequences of each fault. Use the flow chart to back track the A COND error will result in a hard lockout requiring a restart. All other errors must be tripped four times to reach a hard lockout, as set on the dip switch #4 ON, setting #4 OFF will require only two error trips for a hard lockout. IMPORTANT: Freeze Protection Faults If the unit is not equipped with Freeze Protection, use the supplied jumper to short the FREEZE terminals. Open connections will result in faults and lockouts. connection error. To the right of the POWER and STATUS LEDs, a list of number of blinks and their corresponding faults are shown. 1= High Pressure Switch 2= Low Pressure Switch 3= Freeze Protection 4= Condensate Sensor 5= Brownout Protection 10
11 11
12 Figure 9 - UPM Typical Wiring Components 12
13 Figure 10 - UPM Operation Flow Chart 13
14 REV
I/O ZONE 560/583 AND OPERATION MANUAL
UPM I I/O ZONE 560/583 INSTALLATION AND OPERATION MANUAL 1 UNIT PROTECTION MODULE HARDWARE OPERATION IMPORTANT: This manual is for UPM board part numbers 8733 800 259. See controller label as shown in
More informationUPM I. Unit Protection Module. Installation and Operation Manual (2015/06)
UPM I Unit Protection Module Installation and Operation Manual 6 720 220 321(2015/06) 2 Key to Symbols Contents Key To Symbols...2 Warnings...2 Specifications... 3 Unit Protection Module (UPM)....3 Power
More informationHeat Pump Defrost Board Replacement Kit
Bard Manufacturing Company, Inc. Bryan, Ohio 43506 8620-223 Heat Pump Defrost Board Replacement Kit KIT FEATURES This kit is made up of the current defrost control board 8201-129 and a new defrost sensor.
More informationModel 1820 Dehumidifier
Model 1820 Dehumidifier Installation Instructions SAFETY INSTRUCTIONS WARNING 1. 120 Volts may cause serious injury from electric shock. Disconnect electrical power before starting installation or servicing.
More informationPipe Freeze Protection Control SCFP-CO-F130 Installation and Operation Manual
MANUAL Pipe Freeze Protection Control SCFP-CO-F130 Installation and Operation Manual Model FPT 130 Single Point Freeze Protection Heat Trace Control Table of Contents SCFP-CO-F130 Overview... 3 Installation...
More informationTECHNICAL SERVICE DEPARTMENT Technical Service Bulletin Ultra Low NOx PowerVent with Honeywell Electronic Control California Only
Error Code Flash TECHNICAL SERVICE DEPARTMENT Gas Valve Status Flash Code Short flash once every four seconds "Heartbeat", alternates bright/dim One Flash, three second pause Two Flash, three second pause
More informationSingle Point Freeze Protection Heat Trace Control TRACON MODEL FPT 130 Installation and Operation Manual
We manage heat MANUAL Single Point Freeze Protection Heat Trace Control TRACON MODEL FPT 130 Installation and Operation Manual 1850 N Sheridan Street South Bend, Indiana 46628 (574) 233-1202 or (800) 234-4239
More informationSERIES VAC Microprocessor-Based Intermittent Pilot Ignition Control FEATURES APPLICATIONS SPECIFICATIONS DESCRIPTION
R SERIES 35-703 120 VAC Microprocessor-Based Intermittent Pilot Ignition Control F-35-703 July 2016 FEATURES Safe start with DETECT-A-FLAME flame sensing technology Custom pre-purge and inter-purge timings
More informationMODEL FPT-130 SINGLE POINT FREEZE PROTECTION HEAT TRACE CONTROL
TRACON MODEL FPT-130 SINGLE POINT FREEZE PROTECTION HEAT TRACE CONTROL TABLE OF CONTENTS FPT 130 Overview... 2 Installation... 3 Power Source and Load Connections... 4 Temperature Sensor... 5 External
More informationI/O ZONE 560/583 USERS GUIDE
I/O ZONE 560/583 USERS GUIDE 641-224 641-242 641-237 1 Table of Contents Hot Gas Re-Heat Valve On/Off:... 15 THE ZONE CONTROLLER...4 Modulating Re-Heat Valve:... 16 SPECIFICATIONS...5 CONTROLLER COMPONENTS...6
More informationSAFETY INFORMATION AND WARNINGS
This manual refers to the Model SST-3 control panel manufactured since October 31, 2013, which uses a universal (100 277 VAC; 50/60 Hz) power supply. Older units use a voltage-specific power supply and
More informationMANUAL RESET ALARM RELEASE
Fire Door Release MODEL AR-D MANUAL RESET ALARM RELEASE INSTRUCTION MANUAL AR-D GENERAL INFORMATION 1. Review all installation instructions, procedures, cautions and warnings contained within this manual
More informationModel SV - i Series Geothermal Heat Pump
Made in Florida Model SV - i Series Geothermal Heat Pump SV007 Thru SV070 Installation, Operation and Maintenance Manual 8 733 914 818 (2013/8) 2 SV Heat PumpSeries CONTENTS Model Nomenclature... 3 General
More informationWaterFurnace FX10 Application Guide Reversible Chiller
2011 WaterFurnace FX10 Application Guide Reversible Chiller Introduction This manual provides information about the FX10 Water Source Heat Pump (WSHP) controller as it relates to dual compressor water
More informationHP727S. Single speed swimming pool heat pump controller Operation manual TABLE OF CONTENTS
HP727S Single speed swimming pool heat pump controller Operation manual TABLE OF CONTENTS 1. General Description 2. Specifications 3. Installation Instructions 4. Electrical Wiring 5. Instrument Wiring
More informationModel 76 Dehumidifier Control Installation Instructions
Model 76 Dehumidifier Control Installation Instructions READ AND SAVE THESE INSTRUCTIONS The Model 76 is for use with any dehumidifier as an EXTERNAL CONTROL, including Aprilaire Models 1830, 1850(F)(W),
More informationDual Point General Purpose Heat Trace Control TRACON MODEL GPT 230 Installation and Operation Manual
We manage heat MANUAL Dual Point General Purpose Heat Trace Control TRACON MODEL GPT 230 Installation and Operation Manual 1850 N Sheridan Street South Bend, Indiana 46628 (574) 233-1202 or (800) 234-4239
More informationADDITIONAL INFORMATION
MODEL APS-3C AUTOMATIC SNOW/ICE MELTING SYSTEM CONTROL PANEL MODEL APS-4C AUTOMATIC SNOW/ICE MELTING SYSTEM CONTROL PANEL MODEL SC-40C MODULAR SNOW/ICE HEATER CONTROL SYSTEM SAFETY This device provides
More informationSM Field Installed Electric Heat Kit
SM Field Installed Electric Heat Kit HK050 HK100 HK150 HK200 Installation Manual 8733822029 (2018/07) US 2 SM Series Electric Heat Installation Manual Data subject to change 07.2018 8733822029 Installation
More informationPARAGON Commercial Refrigeration Controls
PARAGON Commercial Refrigeration Controls ERC 2 Electronic Refrigeration Control The ERC 2 Electronic Refrigeration Control is a microprocessor-based electronic controller designed to control both the
More informationBasicTroubleshooting Information and Guidelines
BasicTroubleshooting Information and Guidelines BasicTroubleshooting Information and Guidelines Information and Guidelines May 2017 BasicTroubleshooting PRIOR TO CONTACTING CLIMATEMASTER TECHNICAL SUPPORT,
More informationUSER MANUAL WARNING! CONTENTS MODEL SPECIFICATIONS READ ALL INSTRUCTIONS BEFORE PROCEEDING
MODEL Premier Series 3000 USER MANUAL Non-Programmable Single Stage Heat/Cool Digital Thermostat Compatible with low voltage single stage gas, oil or electric heating or cooling systems, including single
More information21D83M-843 Integrated Single Stage Furnace Control Replacement Kit INSTALLATION INSTRUCTIONS
21D83M-843 Integrated Single Stage Furnace Control Replacement Kit INSTALLATION INSTRUCTIONS FAILURE TO READ AND FOLLOW ALL INSTRUCTIONS CAREFULLY BEFORE INSTALLING OR OPERATING THIS CONTROL COULD CAUSE
More information2 THERMOSTAT DETAILS 3 REMOVING OLD THERMOSTAT
CONTENTS Installation Instructions for Heating & Air Conditioning 1F79 n-programmable Heat Pump Thermostat Preparations... 1 Thermostat Details... 1 Removing Old Thermostat... 1-2 Mounting and Wiring...
More information24 VAC Intermittent Pilot Gas Ignition Control
C610U Universal 24 VAC Intermittent Pilot Gas Ignition Control Issue Date: 08/24/2016 Quick Reference Guide The C610U Universal Intermittent Pilot Gas Ignition Control module replaces many popular flame
More informationHeat pump SM024 SM036 SM048 SMO60 SM070. Installation and Maintenance Manual (2013/1)
Heat pump SM024 SM036 SM048 SMO60 SM070 Installation and Maintenance Manual 6 720 220 406 (2013/1) 2 CONTENTS Model Nomenclature... 3 Standard package... 4 General Description... 4 Moving and Storage...
More informationAIR-COOLED CONDENSING UNIT UNITS PRODUCED AFTER JANUARY, 1996 INDEX SCHEMATIC DIAGRAM FIG. NO.
wiring diagrams AIR-COOLED CONDENSING UNIT 566D Sizes 120-240 Cancels: New WD 566D.120.1 11/15/96 UNITS PRODUCED AFTER JANUARY, 1996 INDEX UNIT 566D 120-240 ELECTRICAL CHARACTERISTICS (V-Ph-Hz) SCHEMATIC
More informationIF79 CAUTION CONTENTS YOUR THERMOSTAT REPLACES 1 PREPARATIONS. Installation Instructions for. Heating & Air Conditioning
CONTENTS Installation Instructions for Heating & Air Conditioning IF79 n- Programmable Heat Pump Thermostat Preparations... 1 Thermostat Details... 1 Removing Old Thermostat... 1-2 Mounting and Wiring...
More informationINSTALLATION INSTRUCTIONS WALL MOUNTED PACKAGE AIR CONDITIONERS WA121
INSTALLATION INSTRUCTIONS WALL MOUNTED PACKAGE AIR CONDITIONERS Model: WA121 Bard Manufacturing Company Bryan, Ohio 43506 Since 1914...Moving ahead just as planned. Manual : 2100-234 G Supersedes: 2100-234
More informationtechnical bulletin Control Link RSC Installation Instructions
COMPU TER PROCE SS CONTRO L S Overview The Control Link Refrigeration System Controller (CL-RSC) is an electronic device that can control all functions of a single-compressor refrigeration system, including
More informationMulti-Output Access Control Power Supply Chargers VDC or 24VDC VDC or 4 24VDC.
M Series Multi-Output Access Control Power Supply Chargers Installation Guide Models Include: AL300ULM AL400ULM - 2.5 amp @ 12VDC or 24VDC. - 3 amp @ 12VDC or 4 amp @ 24VDC. AL600ULM AL1012ULM - 6 amp
More informationCHILLGARD M-100. Refrigerant Sensor. Operating Manual. Order No.: /02
CHILLGARD M-100 Refrigerant Sensor Operating Manual GB Order No.: 10086391/02 For the Declaration of Conformity, please visit the product page on MSAsafety.com. MSA Europe GmbH Schlüsselstrasse 12 8645
More informationOWNERS MANUAL YEAR LIMITED WARRANTY READ ALL INSTRUCTIONS BEFORE PROCEEDING. Store this booklet for future reference
3000 Premier Series Non-Programmable Single Stage /Cool Digital Thermostat OWNERS MANUAL Compatible with low voltage single stage gas, oil or electric heating or cooling systems, including single stage
More informationSERVICE MANUAL FOR 6636A & 6636B SERIES TWO TON HIGH EFFICIENCY PACKAGED AIR CONDITIONERS
SERVICE MANUAL FOR 6636A & 6636B SERIES TWO TON HIGH EFFICIENCY PACKAGED AIR CONDITIONERS TABLE OF CONTENTS 1. Warnings & Component Match-Up............................................ 2 2. Unit Specifications..........................................................
More informationOWNERS MANUAL YEAR LIMITED WARRANTY READ ALL INSTRUCTIONS BEFORE PROCEEDING. Store this booklet for future reference
3100 Premier Series Non-Programmable 2 Heat / 2Cool & Heat / Cool Digital Thermostat OWNERS MANUAL Compatible with low voltage multi-stage heat / cool systems with up to two stages of heating and two stages
More informationHoffman Controls 759-ECM. Installation & Operating Instructions. Introduction. Installation. Pre-Installation Information/ Instruction
Hoffman Controls Installation & Operating Instructions Introduction CAUTION Failure to read and understand the accompanying instructions and diagrams prior to energizing the Controller may result in permanent
More informationLM CS Series Heat Pump
LM CS Series Heat Pump LM024 LM036 LM048 LMO60 LM070 Installation, Operation and Maintenance Manual 8 733 920 847 (2014/01) 2 LM CS Series Heat Pump CONTENTS CS/AH Pairing... 3 Key to Symbols... 3 Safety
More informationOFFICE PRO 36 and OFFICE PRO 60 READ THIS MANUAL CAREFULLY FOR INSTRUCTIONS ON CORRECT INSTALLATION AND USAGE AND READ ALL SAFEGUARDS
OPERATION MANUAL OFFICE PRO 36 and OFFICE PRO 60 READ THIS MANUAL CAREFULLY FOR INSTRUCTIONS ON CORRECT INSTALLATION AND USAGE AND READ ALL SAFEGUARDS SECCIÓN EN ESPAÑOL SECTION EN FRANÇAIS AVAILABLE AT
More informationEmerson Inspire 1HDEZ Installation Instructions. Thermostat/Interface Equipment Control TROUBLESHOOTING
Emerson Inspire 1HDEZ-1521 Installation Instructions Thermostat/Interface Equipment Control TROUBLESHOOTING FAILURE TO READ AND FOLLOW ALL INSTRUCTIONS CAREFULLY BEFORE INSTALLING OR OPERATING THIS CONTROL
More informationGreensource i Series SV Model Installation and Maintenance Manual
Greensource i Series SV Model Installation and Maintenance Manual 8733946175 (2016/12) 2 CONTENTS Key to Symbols...3 Safety Warnings...3 Model Nomenclature...4 General Description...5 Moving and Storage...5
More informationTECHNICAL SERVICE GUIDE
GE Consumer Home Services Training TECHNICAL SERVICE GUIDE Electronic Icemaker Pub # 31-9063 8/00 ! IMPORTANT SAFETY NOTICE The information in this service guide is intended for use by individuals possessing
More informationERC2 Control Instructions
Programg ERC2 Control Instructions The ERC 2 control initially powers up displaying 12: AM otherwise it will show the last configured selection (time or temperature). If a power outage occurs during normal
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS The SensorNet I/O Module provides attachment for up to 32 alarms and up to 16 switched devices. An RS-232 or RS-422 communications port is also provided for receiving serial alarms.
More informationMODEL GPT-130 SINGLE POINT HEAT TRACE CONTROL THERMOSTAT
TRACON MODEL GPT-130 SINGLE POINT HEAT TRACE CONTROL THERMOSTAT TABLE OF CONTENTS GPT 130 Overview... 2 Installation... 3 Power Source and Load Connection... 4 Temperature Sensor Installation... 5 Panel
More informationPECO. WavePRO Wireless System INSTALLATION GUIDE: T2500 THERMOSTAT AND R2500 RECEIVER. The Peco WavePRO Wireless System
PECO WavePRO Wireless System INSTALLATION GUIDE: T2500 THERMOSTAT AND R2500 RECEIVER Wireless control for up to 3-HEAT/ 2-COOL heat pump and conventional systems (gas,oil,electric). Benefits: Reduced installation
More informationProgrammable Thermostat
Set & $ave Programmable Thermostat Installation and Operation Manual English Model 44360 Form# 42710-01 20091204 2009 Hunter Fan Co. 2 Table of Contents Important Information... 5 Tools... 6 Uninstalling
More informationDeluxe Programmable Thermostats
Deluxe mable Thermostats T8602D INSTALLATION INSTRUCTIONS APPLICATION The T8602D IV Deluxe mable Thermostat provides electronic control of 24 Vac single-stage heating and cooling systems or 750 mv heating
More informationLodam Compressor Protection Module. Technical manual. Version 3.0 SE-G1
Lodam Compressor Protection Module Technical manual Version 3.0 SE-G1 Contents 1. Read this first... 4 1.1. Reading instructions... 4 1.2. User manual... 4 1.3. Safety... 4 2. General... 5 3. Definitions...
More informationSERIES 35-63J APPLICATIONS FEATURES SPECIFICATIONS AGENCY CERTIFICATIONS
SERIES 35-63J INSTALLATION INSTRUCTIONS FOR REPLACING JOHNSON CONTROLS G77X AND OTHER MODELS WITH FENWAL SERIES 35-63J IP IGNITION CONTROL APPLICATIONS The Fenwal 35-63J series Intermittent Pilot Ignition
More informationT7200D,E Series 2000 Commercial Microelectronic Thermostats
T7200D,E Series 2000 Commercial Microelectronic Thermostats INSTALLATION INSTRUCTIONS APPLICATION The T7200D,E Thermostats provide electronic control of 24 Vac commercial single-zone heating, ventilating
More informationInstaller Guide. WARNING Important Safety Information. 1 Specifications
1 Specifications cont. Premier Series Universal Auto Changeover Up to 3 Heat / 2 Cool Heat Pump or 2 Heat / 2 Cool Conventional Thermostat Installer Guide Before Installing, Programming or Operating, PLEASE
More informationBGH Series Hot Surface Ignition Control
Installation Instructions BGH Series Issue Date April 14, 2011 BGH Series Hot Surface Ignition Control Application The BASO Gas Products BGH Series Hot Surface Ignition (HSI) control is microprocessor
More informationWW/WT SERIES. Table of Contents
WW/WT SERIES Table of Contents Model Nomenclature...1 Initial Inspection...2 Installation...2 Electrical...2 Piping...3 Cooling Tower / Boiler Applications...4 Well Water Systems...4 Earth Coupled Geothermal
More informationCXM/DXM. Application, Operation & Maintenance Instructions 97B0003N08 Revision: 01/10/05. CXM/DXM Digital Heat Pump Controllers.
CXM/DXM CXM/DXM Digital Heat Pump Controllers Application, Operation & Maintenance Instructions 97B0003N08 Revision: 01/10/05 Table of Contents CXM / DXM Control Features Comparison 2 Part I - CXM Control
More informationSet & $ave. Model Programmable Thermostat. installation and operation manual
Set & $ave Programmable Thermostat installation and operation manual Model 44110 42707-01 8-21-06 2 Table of Contents Important Information... 5 Tools... 6 Uninstalling the Existing Unit... 7 Installing
More informationTS93 EMF SERIES. INSPK NO Rev.03/10
TS93 EMF SERIES 1 Each hold open (HO) unit contains a door closer and track assembly with hold open solenoid. The unit can be connected directly to a fire control panel. 1) Read the entire instruction
More information1F98EZ-1421, Easy Install
1F98EZ-1421, -1441 Easy Install For up to 4 Stages and 2 Stages Cool INSTALLATION INSTRUCTIONS APPLICATIONS Configuration Options Single Stage Multi Stage Pump Pump with Dual Fuel FAILURE TO READ AND FOLLOW
More informationFigure 10 or Figure 6
SUPPLEMENT TO INSTRUCTION MANUAL P/N 238-45637-00 and 238-48933-00 (Replaces pg. 32 (238-45637-00) or pg. 28 (238-48933-00) in Wiring Diagram Honeywell A B C VERY HO HO LOW Figure 10 or Figure 6 238-48214-00B
More informationProdigy Flaked and Nugget Ice Machines Technical Review
CM 3 Control System Update Prodigy Flaked and Nugget Ice Machines Technical Review Evaporator Assembly Behind Ice Chute Assembly Fan Blade Control Panel Water Reservoir Air Filter Compressor Ice Chute
More informationMODEL GF PRO AUTOMATIC SNOW/ICE MELTING SYSTEM CONTROL PANEL
MODEL GF PRO AUTOMATIC SNOW/ICE MELTING SYSTEM CONTROL PANEL This manual refers to the Snow Switch Model GF Pro control panel manufactured since October 31, 2013, which uses a universal (100 277 VAC; 50/60
More informationINSTALLATION INSTRUCTIONS FOR 7330C740 FLUSH MOUNT CEILING ASSEMBLY
INSTALLATION INSTRUCTIONS FOR 7330C740 FLUSH MOUNT CEILING ASSEMBLY TABLE OF CONTENTS Warnings...3 Package Contents...3 General Information...3 Supply Ducting And Registers...3 Routing 115 VAC Wiring...5
More informationL SERIES UNITS 504,520M. 10/2001 Supersedes 504,413M
Litho U.S.A. 2 L SERIES UNITS 54,52M /2 Supersedes 54,4M M 6 VERSION 4. INTEGRATED MODULAR CONTROL (IMC) GUIDE TO THE M 6 VERSION 4. INTEGRATED MODULAR CONTROL USED IN L SERIES THROUGH TON UNITS TABLE
More informationIMPORTANT. HOSHIZAKI provides this manual primarily to assist qualified service technicians in the service and maintenance of the icemaker.
73105 IMPORTANT Only qualified service technicians should attempt to service or maintain this icemaker. No service or maintenance should be undertaken until the technician has thoroughly read this Service
More informationINSTALLATION GUIDE AND OWNER S MANUAL. AccuMix II ELECTRIC INSTANTANEOUS WATER HEATER WITH ASSE 1070 APPROVED MIXING VALVE
INSTALLATION GUIDE AND OWNER S MANUAL AccuMix II ELECTRIC INSTANTANEOUS WATER HEATER WITH ASSE 1070 APPROVED MIXING VALVE 2 BEFORE ATTEMPTING ANY INSTALLATION, MODIFICATION OR SERVICE OF THIS HEATER, MAKE
More informationSM CS Series Heat pump
SM CS Series Heat pump SM024 SM036 SM048 SMO60 SM070 Installation, Operation and Maintenance Manual 8 733 920 846 (2015/01) 2 SM CS Series Heat Pump CONTENTS Model Nomenclature... 3 Key to Symbols... 3
More informationTechnical
Service Mode (electronic Control Only) Service Mode is entered by pressing down and holding all keys for 5 seconds. Alarm history of the connected appliance is displayed, alarms are indexed by E1 for most
More information1F Non-programmable Electronic Digital Heat Pump Thermostat INSTALLATION AND OPERATION INSTRUCTIONS
FAILURE TO READ AND FOLLOW ALL INSTRUCTIONS CAREFULLY BEFORE INSTALLING OR OPERATING THIS CONTROL COULD CAUSE PERSONAL INJURY AND/OR PROPERTY DAMAGE. DESCRIPTION Your new White-Rodgers Digital Thermostat
More informationInstallation, Operation & Service Manual
Installation, Operation & Service Manual WARNING Improper installation, adjustment, alteration, service or maintenance can result in death, injury or property damage. Read the Installation, Operation and
More informationT8411R Electronic Heat Pump Thermostat
T84R Electronic Heat Pump Thermostat INSTALLATION INSTRUCTIONS The T84R Heat Pump Thermostat provides 24V control of two-stage heating and one-stage cooling heat pump system with manual changeover from
More informationMR3CCUHV Temperature/Defrost Control
Master Catalog 125 Temperature Controls Section A Product/Technical Bulletin Issue Date 0401 MR3CCUHV Temperature/Defrost Control The MR3CCUHV Temperature/Defrost Control is designed to control the temperature
More informationWARNING Important Safety Information
Builder Series Non-Programmable Thermostats MODEL 1000 MODEL 0 1 2 3 4 Single Stage Heat / Cool Conventional and Heat Pump Multi-Stage 2 Heat / 1 Cool Conventional and Heat Pump Before Installing, Programming
More informationRV Products Division INSTALLATION INSTRUCTIONS FOR SERIES PACKAGE AIR CONDITIONER
RV Products Division INSTALLATION INSTRUCTIONS FOR 46413 SERIES PACKAGE AIR CONDITIONER 1. WARNINGS IMPORTANT NOTICE These instructions are for the use of qualified individuals specially trained and experienced
More informationMANUAL Rev. C 02/15 (800) Environmental Technology, Inc.
MANUAL We Manage Heat Automatic Snow/Ice Melting System Controller SNOW SWITCH MODEL LCD 8 100 240 VAC Installation and Operation Manual Environmental Technology, Inc. 1850 N Sheridan Street South Bend,
More information! WARNING To avoid risk of electrical shock, personal injury or death; disconnect power to range before servicing, unless testing requires power.
Technical Information Electric Downdraft Slide-In Range JES9800BA* JES9900BA* Due to possibility of personal injury or property damage, always contact an authorized technician for servicing or repair of
More informationSM CS Series Heat pump
SM CS Series Heat pump SM024 SM036 SM048 SMO60 SM070 Installation, Operation and Maintenance Manual 8 733 920 846 (2013/11) 2 SM CS Series Heat Pump CONTENTS Model Nomenclature... 3 Key to Symbols... 3
More informationMulti-Output Access Control Power Supply Charger VDC or 24VDC VDC or 3 24VDC.
M Series Multi-Output Access Control Power Supply Charger Installation Guide Models Include: AL300ULM AL400ULM - 2.5 amp @ 12VDC or 24VDC. - 4 amp @ 12VDC or 3 amp @ 24VDC. AL600ULM AL1012ULM - 6 amp @
More information21 TRV Blower Installation Instructions
INSTALL THE ACCENT LIGHT BEFORE THE BLOWER (IF APPLICABLE) If installing the accent light, install it first, leaving the control cover loose for blower rheostat installation. THE BLOWER IS MUCH EASIER
More informationSAFETY INFORMATION AND WARNINGS
SAFETY INFORMATION AND WARNINGS Pilot Duty The GF Pro snow and ice control cannot be used for Pilot Duty applications. Resistive Load Usage Only This product is not for use with Inductive loads. Inductive
More informationDXM CONTROLS. DXM Digital Heat Pump Controllers. Application, Operation, & Maintenance. Table of Contents
Table of Contents DXM CONTROLS DXM Electronic Controls Features Comparison 2 DXM Electronic Heat Pump Controls 3 DXM Physical Dimensions & Layout 4 DXM Controls 5 DXM Service & Application Notes 13 Troubleshooting
More informationMR4PMUHV Electronic. Temperature/Defrost Control with Relay Pack
Master Catalog 125 Temperature Controls Section A Product/Technical Bulletin Issue Date 1098 MR4PMUHV Electronic Temperature/Defrost Control with Relay Pack The MR series temperature controls are designed
More informationLC1 & 2. Fire Alarm Panel 6\VWHPLQVWDOODWLRQRSHUDWLQJ PDLQWHQDQFH LQVWUXFWLRQV
LC1 & 2 Fire Alarm Panel 6\VWHPLQVWDOODWLRQRSHUDWLQJ PDLQWHQDQFH LQVWUXFWLRQV ZIRCONLC1 One Zone Conventional Fire Panel ZIRCONLC2 Two Zone Conventional Fire Panel Compliant with EN54-2:1998 & EN54-4:1998
More informationDiMM Unit. LST Digital Interface Monitor Module (LST-DiMM) MAN3109
LST Digital Interface Monitor Module (LST-DiMM) MAN3109 TABLE OF CONTENTS: Page No. 1 Important Guidelines... 3 2 General Description... 4 Digital Interface Monitor Module... 4 3 Specifications... 5 Leader
More informationDual Point General Purpose Heat Trace Control TRACON MODEL GPT 230 Installation and Operation Manual
We manage heat MANUAL Dual Point General Purpose Heat Trace Control TRACON MODEL GPT 230 Installation and Operation Manual 1850 N Sheridan Street South Bend, Indiana 46628 (574) 233-1202 or (800) 234-4239
More informationProdigy Plus - D Series Cuber Technical Review
Prodigy Plus - D Series Cuber Technical Review Water Distributor Control Panel Air Filter ice Thickness Sensor Lower Light and Switch Panel Water Pump Water Level Sensor & Guard Curtain Switch and Magnet
More informationAG Series Electric Heaters
AG Series Electric Heaters Installation, Operation and Maintenance Instructions Internal Auxililary Electric Heat 97B0005N03 Table of Contents Overview 3 Vertical Upflow Installation 4 Horizontal Installation
More informationWater Source Heat Pump Module Technical Guide
Factory Packaged Controls Tulsa Water Source Heat Pump Module WSHP WSHP Protection Module Module Orion No.: OE334-23-WPM-A NON-DIGITAL COMPRESSORS #1 THRU #4 +5V SUCT. +5V SUCTION PR. SENSOR PRES PRES
More informationINSTALLATION INSTRUCTIONS
2008 Lennox Industries Inc. Dallas, Texas, USA INSTALLATION INSTRUCTIONS ComfortSense 3000 Series Models / / 5/2 Day Programmable Thermostats RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE // 5/2 Day Programmable
More informationAuxiliary Electric Heater Interface kit ASKHTR
Auxiliary Electric Heater Interface kit ASKHTR Installation, Operation & Maintenance Table of Contents General Information 2 INSTRUCTIONS for 1: Boilerless 2 INSTRUCTIONS for 2: Supplemental 3 Typical
More information50M56U-843 INSTALLER MUST READ DESCRIPTION PRECAUTIONS WARNING CAUTION
50M56U-843 Universal Single Stage HSI Integrated Furnace Control Kit INSTALLATION INSTRUCTIONS INSTALLER MUST READ PAGE 3 CONTAINS WIRING HARNESS AND BLOWER CONNECTION INSTRUCTIONS FOR ALL APPLICATIONS
More informationOPERATION MANUAL. CLASSIC 10 and CLASSIC 18. Unit Serial Number Range: 1111XXXX### to Present (From November 2011 to Present)
OPERATION MANUAL CLASSIC 10 and CLASSIC 18 Unit Serial Number Range: 1111XXXX### to Present (From November 2011 to Present) READ THIS MANUAL CAREFULLY FOR INSTRUCTIONS ON CORRECT INSTALLATION AND USAGE,
More information! WARNING To avoid risk of electrical shock, personal injury or death; disconnect power to range before servicing, unless testing requires power.
Technical Information Electric Slide-In Range JES9750BA* JES9860BA* Due to possibility of personal injury or property damage, always contact an authorized technician for servicing or repair of this unit.
More informationLow Water Cutoff (LWCO) IQ Option Card p/n , for Hot Water Boilers
Low Water Cutoff (LWCO) IQ Option Card p/n 102711-01, 102714-01 for Hot Water Boilers Instruction Sheet 102-360 APPLICATION The Low Water Cutoff (LWCO) IQ Option Cards are advanced, microprocessor based
More informationModel 17A00 Expansion Enclosure
HOME AUTOMATION, INC. Model 17A00 Expansion Enclosure Installation Manual Document Number 17I00-1 Rev A March, 2002 Home Automation, Inc. Model 17A00 Expansion Enclosure Installation Manual Document Number
More informationInstallation Instructions
Installation Instructions Sabbath Mode Product Kit ZSAB1 For Use With Monogram Built-In s: 36", 42" & 48" Side-by-Side R Models (Manufactured On or After February 2004) and X Models 36" Bottom-Freezer
More informationOFFICE PRO 63 READ THIS MANUAL CAREFULLY FOR INSTRUCTIONS ON CORRECT INSTALLATION AND USAGE AND READ ALL SAFEGUARDS
OPERATION MANUAL OFFICE PRO 63 READ THIS MANUAL CAREFULLY FOR INSTRUCTIONS ON CORRECT INSTALLATION AND USAGE AND READ ALL SAFEGUARDS SECCIÓN EN ESPAÑOL SECTION EN FRANÇAIS AVAILABLE AT WWW.MOVINCOOL.COM
More informationHOSHIZAKI AMERICA, INC. SERVICE BULLETIN
HOSHIZAKI AMERICA, INC. SERVICE BULLETIN Subject: E SERIES CONTROL BOARD Page 1 of 4 Beginning in February, the KM Universal Alpine replacement control board part number 2U0139-01, will sub to a new Control
More informationFAULT CODES. Included in this section are instructions to Reset the two Hot Tank Overload Devices (High Safety Limit).
FAULT CODES Fault Code Index 1. Blue Chilling LED Flashing Cold Sensor Fault 2. Red Heating LED Flashing Hot Sensor Fault 3. Green LED Flashing Filter Service Alert 4. All but Power Button LEDs Flashing
More informationT7079A,B Solid State Remote Temperature Controllers
T7079A,B Solid State Remote Temperature Controllers FEATURES PRODUCT DATA Switch selection of heat or cool mode. Temperature sensing up to 400 feet. Does not require field calibration. 0K NTC temperature
More informationSERIES VAC Microprocessor-Based Direct Spark Ignition Control FEATURES APPLICATIONS SPECIFICATIONS DESCRIPTION. Export Information (USA)
R SERIES 35-70 120 VAC Microprocessor-Based Direct Spark Ignition Control F-35-70 November 2015 FEATURES Safe start with DETECT-A-FLAME flame sensing technology Custom pre-purge and inter-purge timings
More informationGUIDE SPECIFICATIONS. WW Series Water-to-Water Reverse Cycle Chillers & Low Temp Boilers. WW Reverse Cycle Chillers / Low Temperature Boilers
GUIDE SPECIFICATIONS WW Series Water-to-Water Reverse Cycle Chillers & Low Temp Boilers WW024-072 Reverse Cycle Chillers / Low Temperature Boilers GENERAL Units shall be Underwriter Laboratories (UL) listed
More information