Wireless Alarm system s manual

Size: px

Start display at page:

Download "Wireless Alarm system s manual"

Edwina Nicholson
5 years ago
Views:

1 MOUNTVIEW TECH AUSTRALIA PTY LTD Wireless Alarm system s manual ADS ECO GSM320 Series ADS Security 1/11/2011

2 1. Before You Begin For your safety and the safety of others, and to ensure that you get the most out of the wireless alarm kit, please read and adhere to these guidelines. Make sure product is fixed correctly and stable if fastened in place. Do not operate if wires and terminals are exposed. Do not put the GSM main panel near large scale metal objects or household appliances with high frequency interference. Do not install the PIR sensors in direct sunlight or near any device which emits heat or cold, such as air conditioners, refrigerators, ovens, heaters, microwaves or other electronic equipment which generates heat as a by product of operation. Replace the batteries in the units regularly. There are batteries in the remote controls, window/door sensors, wireless keypad, PIR motion sensors and smoke detectors. Test the alarm periodically to ensure it is working properly. The strength of the wireless signal is dramatically affected by the placement of the antenna extend the length of the antenna if you need better results. Keep this booklet in a safe place. This alarm system is designed to be, and acts as, a theft deterrent. This system, like any other, cannot offer complete protection for your home or business it is simply an alarm system. Like all practical systems, it has limitations and it could be disabled by a skilled intruder. We suggest that you avoid relaying solely on the wireless alarm system to protect your property, but use it as part of a comprehensive security solution. 2. INTRODUCTION Main features of GSM320 Alarm System Six phone numbers can receive SMS /CALL from alarm, 10 seconds ISD automatic voice recording. Use SIMCOM GSM module (industrial module). Have eight wireless zones and four wired zone. Each wireless zone can be equipped with up to 160 wireless accessories. SMS contents include which zone which detector is triggered. Set Alarm / Arm delay easily and switch Away/ Home arm mode flexibly. Has output relay which can control home appliances, such as light, air conditioner, roller shutters and so on. Two way voice communication to the person on the spot. Control the alarm system remotely by using phone call no matter where you are as long as you can ring your alarm system. After sale support for ebay buyer estore3150@gmail.com 1

3 Inner back up battery for 24 hours. Power off / on alert by sending message to Phone number 1. Easy and quick to be installed and operated. GSM320 main panel The main panel is the heart of the wireless alarm system. It is responsible for monitoring the various sensors throughout your home and or triggering the alarm signal when one of them reports a disturbance. 1. Power ON/OFF 2. DC12V input 3. Siren connection 4. Code button 5. Recode button 6. Relay to control the home appliances Speaker two way voice communications 12V, GND, L4 L1 for the wired detectors 7. SIM card slot 8. Antenna pedestal 9. Power light 10. Network light 11. Alarm light 12. Z1 Z8 light Function Signal Interpretation Buzzer Short beep twice Error in command Long beep once One correct command received Power LED Not lit Without electricity Network LED Blinking every 1 second GSM signal weak or network not found. Blinking every 3 second GSM module &network working properly. Alarm LED Always lit Alarm is alerting Blinking Alerting delayed Window/door sensor Door /windows sensors are extremely reliable, and will be triggered every time the door on which they are mounted is opened. After sale support for ebay buyer estore3150@gmail.com 2

When the two parts of the sensor are extremely close to one another (ideally touching) the sensor is deactivated.

They are reliable and, if installed correctly, can safeguard doors and windows from being opened without your knowledge.

PIR motion sensor spaces. Some garages may be large enough that one sensor cannot cover that whole area we suggest testing this in the actual environment if there s any doubt.

The Passive InfraRed (PIR) sensor will, under typical conditions, detect a human being moving around within approximately 10m from the sensor.

4 When the two parts of the sensor are extremely close to one another (ideally touching) the sensor is deactivated. As soon as the two parts are moved apart by about 10 15mm, this will cause the transmitter to send the alarm signal. We suggest using the window/door gap sensors as your primary alarm triggers. They are reliable and, if installed correctly, can safeguard doors and windows from being opened without your knowledge. However, these types of sensors can be circumvented if a window or fragile door were broken rather than opened. Thus, we suggest using the infrared sensors as a backup to the window/door sensors. PIR motion sensor spaces. Some garages may be large enough that one sensor cannot cover that whole area we suggest testing this in the actual environment if there s any doubt. The sensor has a horizontal 110 vertical 60 field of view. The main blind spots are above, below or behind the sensor itself. The Passive InfraRed (PIR) sensor will, under typical conditions, detect a human being moving around within approximately 10m from the sensor. This is an average value, as the actual detection range is between 5m and 12m. As the performance of the sensor is determined primarily by environmental conditions. No guarantees can be offered regarding the detection range. However, the range is typically sufficient for the majority of interior Typically, the ideal placement in an environment is the upper corner of a room, facing slightly towards the ground (perhaps 20 25, depending on the height of the sensor). Try to cover typical paths through the room, focussing particularly on After sale support for ebay buyer estore3150@gmail.com 3

likely entry and exit points. If the room has several entry points, try to cover as many of these as practicable.

Remote Control The remote control is the electronic key. Treat it like any other key keeping it on your keychain. Disarm: Used to disarm the wireless alarm system, whichever mode it is in.

Key guard: A small sliding tab which can be placed to prevent accidental arming or disarming of your alarm system when being carried in a pocket or bag.

5 likely entry and exit points. If the room has several entry points, try to cover as many of these as practicable. A visible PIR motion sensor can be a great deterrent to intruders but on the other hand, skilled intruders can avoid obviously visible sensors. Try to mix it up a bit. Remote Control The remote control is the electronic key. Treat it like any other key keeping it on your keychain. Disarm: Used to disarm the wireless alarm system, whichever mode it is in. Arm (away mode): Arm away mode. (All detectors work) Arm (home mode): Arm home mode. (Some detectors work and other not) Alarm (emergency): Trigger the alarm immediately whichever mode it is in. Key guard: A small sliding tab which can be placed to prevent accidental arming or disarming of your alarm system when being carried in a pocket or bag. Wireless keypad The wireless keypad is the electronic key as same as remote control. The keypad will be a better solution for large family or business user. * / Away: Arm away mode. (All detectors work) # / Home: Arm home mode. (Some detectors work and other not) 0/ Disarm: Used to disarm the After sale support for ebay buyer estore3150@gmail.com 4

6 wireless alarm system, whichever mode it is in. Keypad is locked automatically for power saving. Please press the [*] key to unlock. To operate the keypad always enter password first. Fox example: use keypad to disarm the alarm system by password [0]. The password in here is for keypad itself only which is different as the main system s password. You could set up both passwords the same or different. Change the password for the keypad by command: [*][2][*] new password[#], make sure put away the watch dog after changing password. Intruder who knows this command will operate the alarm system by keypad if you leave the watch dog with keypad. This unit has two new unique designs: Battery / power supply: use both or one of them. Give you more freedom. Watch dog: keep it in a safe place after setting. No one can change the setting without this watch dog including the skilled intruder. Dual beam infrared barrier The dual beam infrared barrier will detect an objective when it blocks any neighbour two or more infrared lights over 40ms. It s designed for outdoor environment, could be installed in driveway, carport, drive through shop, balcony and so on. 1. protective lid 2. Installation seat (360 rotation) 3. line seat 4. protection flake 5. Plastic window 6. aluminium alloy outer cover 7. inner Circuit Board 3. INSTALLATION Open the alarm kit and determine where each piece is to be located. The PIR sensors usually mounted high on a wall and directed into the room requiring protection such as a lounge room or hallway. The main panel is usually located somewhere within 1 meter of a power point. The sensors must not be located more than 80 metres from the main panel. Installing the GSM320 main panel: After sale support for ebay buyer estore3150@gmail.com 5

7 Get SIM card ready which should have credit. Then pinch the yellow point of SIM slot by pen or tools, pull out the SIM tray. SIM card s metal side should face down. Insert back SIM card tray carefully. Connect the power supple, the internal siren, antenna and voice speaker. Switch ON/OFF. Remember: put the SIM in before your turn on the alarm system. Otherwise the system may have trouble to find GSM network. Installing wireless PIR sensors: Installation height is about 2.2 meters above ground and you need consider the best coverage. (Ref: page3) Installing wireless Door/Window sensor: The transmitter should be installed on the fixed frame and the trigger should be placed on the movable side with a gap not exceeding 1CM. The door/window sensors can attach most surfaces by double sided mounting tape. Installing wireless keypad: Install the keypad at main entrance and must under cover. Keep the watch dog separately in a safe place. You need plug watch dog on when you change the password in the future. Installing Dual beam infrared barrier: Connect the power cable as demonstration. + pole connect power adapter s red cable, pole connect power adapter s black cable. Screw both parts onto the position where you prefer. And make sure the same level of two parts. Turning the barrier slightly to make sure two parts are facing each other. 4. PROGRAMMING GSM320 PASSWORD: The default password is We strongly recommend choosing a new password as soon as possible. SMS Command: * 1234 #811 * new password # Code/ Register the wireless Accessories: Hold the code button for 2 seconds, the Z1 (zone1) LED should turn to red with one beep. Release the code button, and you can start to trigger all wireless accessories to let main panel recognize them. Remember, you can press the RECORD button to change the ZONE number, and code the sensor to different ZONE. Press the code button to return. System will return automatically if there is no operation in 30 seconds during code condition. Record voice message: Connect the voice speaker to the main panel. After sale support for ebay buyer estore3150@gmail.com 6

8 Hold the [record] button for 2 seconds, and then release the button when all ZONE LED glitter at the same time, with one beep. Press the [code] button to record 30 seconds voice message or press the [record] button to listen what you have recoded. Set inner defence zone for home arm mode: Zone 8 is the inner zone. Please code the wireless detectors and sensors into the eightdefence zone if those detectors and sensors will not work during home arm mode. Reset the system: Press on the [code] button and switch ON/OFF at same time. The middle two LEDs will be on for few seconds, then two LEDS go opposite, release [code] button until 4 LEDS in the middle are red at the same time. Should hear one long beep after 2 3 minutes if reset successfully. Programming command: General one command pattern sent via SMS is * [password] # [command] *[parameter] # General more than one command pattern sent via SMS is * [password] # [command1] *[parameter1] # [command2] *[parameter2] # [command3] *[parameter3] # [command4] *[parameter4] # Commands and parameters table: command function parameter details 810 Phone number adjustment 0 Add 0 at front of the phone numbers. 811 Change password New password 1234 (default password) 812 Recycling times to dial up the phone numbers 1 once 2 twice 3 Triple (default times) 813 Siren sound when pressing 0 Silent remote control 1 On (default is ON) 814 How long will siren on 0 Silent when system alarming minute 30 minutes 815 Delay time to arm second 99 seconds 816 Dial up / SMS 0 Send message and call the phone numbers (default). 1 Send messages only. 2 Call the numbers only. 819 Delay time to alarm second 99 seconds 831 Phone number 1 Add * at front of the phone number if that 832 Phone number Phone number 3 number needs receive SMS. Get rid of the first number 0 when you put After sale support for ebay buyer estore3150@gmail.com 7

9 834 Phone number 4 the phone number into the system. For 835 Phone number 5 example: 836 Phone number 6 Mobile: * Mobile: Landline: Country code 61 Australia 1 USA 44 England 900 Message content Automatically including PIR/smoke /panic/ sensors detail in the SMS. System will send message to phonenumber1 when power is on/off no matter which mode the system is in. 5. Operate in long distance call in the GSM320 alarm system and hear one long beep. key in password, ( one long beep for correct password, two short beeps for incorrect password. The system will hang up after receiving 3 times incorrect password). key in [command] Operate in long distance commands table: Command Function 1 Arm (one beep if successfully) 2 Disarm (one beep if successfully) 3 Siren sounds for 3 seconds 4 Turn on the output relay (home appliances) 5 Turn off the output relay (home appliances) 0 Two way communicate. (Press * to continue. 0 to returen. 1, 2, 3, 4, and 5 to adjust the voice. 1 is the lowest voice.) * Listen in # return 6. TROUBLESHOOTING Problem Probable Reasons Available Solutions 1. alarm can t dial or run out of credit of your SIM top up your SIM SMS Alerting phone number was re set the phone numbers 2. cannot longdistance operation set incorrectly password input wrongly ( or forgotten ) and county code retry password or reset password After sale support for ebay buyer estore3150@gmail.com 8

10 3. No voice message indication when alerting 4. remote control (keypad) out of order 5. infrared detector out of order 6. siren without sound 7. the transmission distance of detector to panel shorten 8. the network LED blinking quickly voice message not recorded coding un matched with the Panel insufficient battery power low battery low power siren plug or jack in short circuit or broken line siren out of order closed siren by command positive and ground wires of siren reversed a nearby emitter is sending signal Panel receiver stoppage standby battery of the Panel insufficient SIM card un loaded SIM card is setting PIN code GSM signal weak record voice message re learn the remote control change battery to correct type change the battery change to the same type battery repair or change plug or jack change the jack line activate siren by command use another siren to double check reverse the wires to try move one detector next to panel and try identify the interfering source and eliminate it check Panel power whether plugged well reload SIM card cancel PIN code of SIM change to place with strong signal 7. Technical Parameters GSM320 Main Panel: Operating voltage: DC12V Average power: AC/DC exchanger 2A. Work currency: less than 50 ma Wireless receiving distance: 100m Operating Frequency: MHZ GSM 850/ 900/1800/1900MHZ Operating voltage: DC12V, AC 220/110V Wireless receiving distance: 100m 250m Voice speaker: After sale support for ebay buyer estore3150@gmail.com 9

11 Siren: Volume: 110 db Working Condition: Temperature Humidity 90% rh Wireless Door/Window Gap Detector: Power Supply: DC12V (inner 12V battery) Static Current: 20 ma Transmission Current: 15mA Transmission Frequency: 433MHZ Transmission Distance: less 80M Internal Distance: 15 mm Working Condition: Temperature Humidity 90% rh Wireless P.IR Detector: Power Supply: DC9V (inner 9V battery) Static Current: 100 ma Transmission Current: 20mA Frequency: 433MHZ Transmission Distance: less 80M Detective Speed: 0.3 3m/s Detective Distance: 5 12M Detective Range: Horizontal 110 Vertical 60 Working Condition: Temperature Humidity 90 rh Remote Control: Power Supply: DC12V (inner DC12V battery) Transmission Current: 15mA Frequency: 433MHZ or 315MHZ Transmission Distance: less 80M After sale support for ebay buyer estore3150@gmail.com 10

MOBILE CALL GSM Alarm System User s Manual

MOBILE CALL GSM Alarm System User s Manual Profile For a better understanding of this product, please read this user manual thoroughly before using it. Contents Function Introduction (3) Alarm Host Diagram