OCCUPANCY INSPECTION FORM

Transcription

1 NMSU FIRE DEPARTMENT 1510 Wells Street Las Cruces, NM (575) OCCUPANCY INSPECTION FORM Building Name: Building ID: Street Address: Phone #: Emergency Contact: Emergency Phone #: Building Monitor: Property Type: PASS FAIL N/A EXITS Provide exit signs with letters at least 6-inches high on a contrasting background. (IFC 2006 SEC 1011) Remove obstructions from exits, aisles, corridors, and stairways. (IFC 2006 SEC 1028) Remove storage from beneath exit stairs. (IFC 2006 SEC ) Repair or maintain exit doors and hardware to operate properly. (IFC 2006 SEC &1028) Unlock all exit doors during business hours. (IFC 2006 SEC ) EXIT LIGHTING Provide lighting for exits, aisles, corridors, and stairways. (IBC 2009 SEC 1006) Repair lighted exit signs or emergency lighting. (IFC 2006 SEC 1011) FIRE EXTINGUISHERS Mount extinguishers where readily available, not more than 5-feet above floor. (IFC 2006 SEC 906.9) Post signs indicating location where extinguishers are not readily visible. (IFC 2006 SEC 906.6) Portable fire extinguishers are due for annual maintenance on (IFC 2006 SEC 906 & NFPA ): COMMERCIAL KITCHEN Portable K fire extinguishers located in kitchen. (IFC 2006 SEC ) Portable K/hood suppression system fire extinguishers are due for 6-month maintenance on (IFC 2006 SEC ) (mm/yy) : Exhaust hoods/ducts and grease filters will be installed, repaired and maintained to operate properly (IFC 2006 SEC 609) Clean grease filters and hood/duct system over cooking equipment. (IFC 2006 SEC & ) Deep fryers will have the proper size Class K extinguisher available. (IFC 2006 SEC ) Install, repair and maintain the manual activation device for the fire extinguishing system. (IFC 2006 SEC ) FIRE PROTECTION ACCESS and EQUIPMENT Install approved protective covers on fire department hose connection. (IFC 2006 SEC ) Maintain access to and operation of standpipes, fire hose, sprinkler valves, fire hydrants, fire extinguishers, and other fire protection equipment. (IFC 2006 SEC 912.2) Provide and maintain smoke detectors and/or CO detectors in proper operating condition. (IFC 2006 SEC ) Provided minimum 4-inches high address numbers so they are visible from the street. (IFC 2006 SEC 505.1) Remove obstructions and provide access in fire lanes. (IFC 2006 SEC 912.2) The X system(s) is/are due for confidence testing and certification. Please see the attached report. FIRE SEPARATIONS Keep attic and scuttle covers closed, and ceiling tiles in place. (IFC 2006 SEC 507 & 703) Remove obstructions from fire doors and maintain to operate properly. (IFC 2006 SEC 703.2) Seal unapproved openings with approved material. (IFC 2006 SEC & ) HOUSEKEEPING Arrange storage in orderly manner to provide for exiting and fire department access. (IFC 2006 SEC 504.2) Boiler, mechanical, and electrical panel rooms shall not be used for storage. (IFC 2006 SEC ) Chain all compressed gas cylinders in an upright position and provide protective caps. (IFC 2006 SEC ) Move the dumpster at least 5-feet from the building or overhangs. (IFC 2006 SEC 304.3) Post and enforce 'No Smoking' signs. (IFC 2006 SEC ) Provide approved waste containers for combustible waste. (IFC 2006 SEC &304.3) Reduce storage height to at least 2-feet below ceiling. (IFC 2006 SEC ) Remove or store rubbish, waste material, oily rags in closed metal containers. (IFC 2006 SEC & 304.3) Remove storage to at least 18-inches below level of sprinklers (36-inches for storage piled over 12-feet high). (IFC 2006 SEC ) FLAMMABLE LIQUIDS Discontinue pouring from containers exceeding 5-gallons or provide pump taking suction from top. (IFC 2006 SEC & 3405) Discontinue use of Class 1 liquids (gasoline, etc.) for cleaning. (IFC 2006 SEC ) Storage in excess of 10-gallons shall be in an approved cabinet. (IFC 2006 SEC ) Store liquids away from exits, aisles, corridors, or stairways. (IFC 2006 SEC ) Use only approved safety can for portable dispensing of flammable liquids. (IFC 2006 SEC ) ELECTRICAL Discontinue use of extension cords in lieu of permanent wiring. (IFC 2006 SEC 605.5) Discontinue use of non-approved multi-plug adapters. (IFC 2006 SEC 605.4) Each outlet box shall have a cover faceplate or fixture canopy. (IFC 2006 SEC 605.6) Maintain at least 30-inches clearance in front of electrical panel. (IFC 2006 SEC 605.3) Maintain wiring in good condition and protect from damage. (IFC 2006 SEC 605.1) An inspection has been made of these premises to determine if any violations of the adopted NMSU fire code exist. If violations have been found, this shall serve as your official notice, and an inspector shall explain each violation fully. All violations must be corrected immediately. A re-inspection of the premises will be made at a future date to verify the required corrections. Failure to correct the violations shall cause the owner/responsible party of the property to be in possible violation of NM State Statues. Should you require assistance with matters regarding this inspection, please call the NMSU Fire Department office at (575) I, (Print Name), have read and acknowledge the conditions of this notice. Responsible Person (Sign): Inspector (Print): (Sign): Date: Re-inspection: Yes No Date for Re-Inspection:

2 EXITS Provide exit signs with letters at least 6-inches high on a contrasting background. (IFC 2006 CHAPTER 10 MEANS OF EGRESS SEC 1011) SECTION 1011 EXIT SIGNS [B] Where required. Exits and exit access doors shall be marked by an approved exit sign readily visible from any direction of egress travel. Access to exits shall be marked by readily visible exit signs in cases where the exit or the path of egress travel is not immediately visible to the occupants. Exit sign placement shall be such that no point in a corridor is more than 100 feet ( mm) or the listed viewing distance for the sign, whichever is less, from the nearest visible exit sign. 1. Exit signs are not required in rooms or areas that require only one exit or exit access. 2. Main exterior exit doors or gates that are obviously and clearly identifiable as exits need not have exit signs where approved by the fire code official. 3. Exit signs are not required in occupancies in Group U and individual sleeping units or dwelling units in Group R-1, R-2 or R Exit signs are not required in sleeping areas in occupancies in Group I In occupancies in Groups A-4 and A-5, exit signs are not required on the seating side of vomitories or openings into seating areas where exit signs are provided in the concourse that are readily apparent from the vomitories. Egress lighting is provided to identify each vomitory or opening within the seating area in an emergency Illumination. Exit signs shall be internally or externally illuminated. Exception: Tactile signs required by Section need not be provided with illumination Tactile exit signs. A tactile sign stating EXIT and complying with ICC A117.1 shall be provided adjacent to each door to an egress stairway, an exit passageway and the exit discharge Internally illuminated exit signs. Internally illuminated exit signs shall be listed and labeled and shall be installed in accordance with the manufacturer s instructions and Section 2702 of the International Building Code. Exit signs shall be illuminated at all times Externally illuminated exit signs. Externally illuminated exit signs shall comply with Sections through Graphics. Every exit sign and directional exit sign shall have plainly legible letters not less than 6 inches (152 mm) high with the principal strokes of the letters not less than 0.75 inch (19.1 mm) wide. The word EXIT shall have letters having a width not less than 2 inches (51 mm) wide, except the letter I, and the minimum spacing between letters shall not be less than inch (9.5 mm). Signs larger than the minimum established in this section shall have letter widths, strokes and spacing in proportion to their height. The word EXIT shall be in high contrast with the background and shall be clearly discernible when the means of exit sign illumination is or is not energized. If a chevron directional indicator is provided as part of the exit sign, the construction shall be such that the direction of the chevron directional indicator cannot be readily changed Exit sign illumination. The face of an exit sign illuminated from an external source shall have an intensity of not less than 5 foot-candles (54 lux) Power source.

3 Exit signs shall be illuminated at all times. To ensure continued illumination for a duration of not less than 90 minutes in case of primary power loss, the sign illumination means shall be connected to an emergency power system provided from storage batteries, unit equipment or an on-site generator. The installation of the emergency power system shall be in accordance with Section 2702 of the International Building Code. Exception: Approved exit sign illumination means that provide continuous illumination independent of external power sources for a duration of not less than 90 minutes, in case of primary power loss, are not required to be connected to an emergency electrical system. Remove obstructions from exits, aisles, corridors, and stairways. (IFC 2006 CHAPTER 10 MEANS OF EGRESS SEC 1028) SECTION 1028 MAINTENANCE OF THE MEANS OF EGRESS General. The means of egress for buildings or portions thereof shall be maintained in accordance with this section Reliability. Required exit accesses, exits or exit discharges shall be continuously maintained free from obstructions or impediments to full instant use in the case of fire or other emergency when the areas served by such exits are occupied. Security devices affecting means of egress shall be subject to approval of the fire code official Obstructions. A means of egress shall be free from obstructions that would prevent its use, including the accumulation of snow and ice Exit signs. Exit signs shall be installed and maintained in accordance with Section Decorations, furnishings, equipment or adjacent signage that impairs the visibility of exit signs, creates confusion or prevents identification of the exit shall not be allowed Furnishings and decorations. Furnishings, decorations or other objects shall not be placed so as to obstruct exits, access thereto, egress therefrom, or visibility thereof. Hangings and draperies shall not be placed over exit doors or otherwise be located to conceal or obstruct an exit. Mirrors shall not be placed on exit doors. Mirrors shall not be placed in or adjacent to any exit in such a manner as to confuse the direction of exit Emergency-escape openings. Required emergency escape openings shall be maintained in accordance with the code in effect at the time of construction, and the following: Required emergency escape and rescue openings shall be operational from the inside of the room without the use of keys or tools. Bars, grilles, grates or similar devices are allowed to be placed over emergency escape and rescue openings provided the minimum net clear opening size complies with the code that was in effect at the time of construction and such devices shall be releasable or removable from the inside without the use of a key, tool or force greater than that which is required for normal operation of the escape and rescue opening Testing and maintenance. All two-way communication systems for areas of refuge shall be inspected and tested on a yearly basis to verify that all components are operational. When required, the tests shall be conducted in the presence of the fire code official.

4 Remove storage from beneath exit stairs. (IFC 2006 CHAPTER 3 GENERAL PRECAUTIONS AGAINST FIRE SEC ) SECTION 315 MISCELLANEOUS COMBUSTIBLE MATERIALS STORAGE General. Storage, use and handling of miscellaneous combustible materials shall be in accordance with this section. A permit shall be obtained in accordance with Section Storage in buildings. Storage of combustible materials in buildings shall be orderly. Storage shall be separated from heaters or heating devices by distance or shielding so that ignition cannot occur Ceiling clearance. Storage shall be maintained 2 feet (610 mm) or more below the ceiling in nonsprinklered areas of buildings or a minimum of 18 inches (457 mm) below sprinkler head deflectors in sprinklered areas of buildings Means of egress. Combustible materials shall not be stored in exits or exit enclosures Equipment rooms. Combustible material shall not be stored in boiler rooms, mechanical rooms or electrical equipment rooms Attic, under-floor and concealed spaces. Attic, under-floor and concealed spaces used for storage of combustible materials shall be protected on the storage side as required for 1-hour fire-resistance-rated construction. Openings shall be protected by assemblies that are self-closing and are of noncombustible construction or solid wood core not less than 13/4 inches (44.5 mm) in thickness. Storage shall not be placed on exposed joists. 1. Areas protected by approved automatic sprinkler systems. 2. Group R-3 and Group U occupancies Outside storage. Outside storage of combustible materials shall not be located within 10 feet (3048 mm) of a property line. 1. The separation distance is allowed to be reduced to 3 feet (914 mm) for storage not exceeding 6 feet (1829 mm) in height. 2. The separation distance is allowed to be reduced when the fire code official determines that no hazard to the adjoining property exists Storage beneath overhead projections from buildings. Where buildings are protected by automatic sprinklers, the outdoor storage, display and handling of combustible materials under eaves, canopies or other projections or overhangs is prohibited except where automatic sprinklers are installed under such eaves, canopies or other projections or overhangs Height. Storage in the open shall not exceed 20 feet (6096 mm) in height Storage underneath high-voltage transmission lines. Storage located underneath high-voltage transmission lines shall be in accordance with Section

5 Repair or maintain exit doors and hardware to operate properly. (IFC 2006 CHAPTER 10 MEANS OF EGRESS SEC &1028) SECTION 1008 DOORS, GATES AND TURNSTILES [B] Door operations. Except as specifically permitted by this section egress doors shall be readily openable from the egress side without the use of a key or special knowledge or effort Hardware. Door handles, pulls, latches, locks and other operating devices on doors required to be accessible by Chapter 11 of the International Building Code shall not require tight grasping, tight pinching or twisting of the wrist to operate Hardware height. Door handles, pulls, latches, locks and other operating devices shall be installed 34 inches (864 mm) minimum and 48 inches (1219 mm) maximum above the finished floor. Locks used only for security purposes and not used for normal operation are permitted at any height. Exception: Access doors or gates in barrier walls and fences protecting pools, spas and hot tubs shall be permitted to have operable parts of the release of latch on self-latching devices at 54 inches (1370 mm) maximum above the finished floor or ground, provided the self-latching devices are not also self-locking devices operated by means of a key, electronic opener or integral combination lock Locks and latches. Locks and latches shall be permitted to prevent operation of doors where any of the following exists: 1. Places of detention or restraint. 2. In buildings in occupancy Group A having an occupant load of 300 or less, Groups B, F, M and S, and in places of religious worship, the main exterior door or doors are permitted to be equipped with key-operated locking devices from the egress side provided: 2.1. The locking device is readily distinguishable as locked, 2.2. A readily visible durable sign is posted on the egress side on or adjacent to the door stating: THIS DOOR TO REMAIN UNLOCKED WHEN BUILDING IS OCCUPIED. The sign shall be in letters 1 inch (25 mm) high on a contrasting background, 2.3. The use of the key-operated locking device is revokable by the fire code official for due cause. 3. Where egress doors are used in pairs, approved automatic flush bolts shall be permitted to be used, provided that the door leaf having the automatic flush bolts has no doorknob or surface-mounted hardware. 4. Doors from individual dwelling or sleeping units of Group R occupancies having an occupant load of 10 or less are permitted to be equipped with a night latch, dead bolt or security chain, provided such devices are openable from the inside without the use of a key or tool Bolt locks. Manually operated flush bolts or surface bolts are not permitted. 1. On doors not required for egress in individual dwelling units or sleeping units. 2. Where a pair of doors serves a storage or equipment room, manually operated edgeor surface-mounted bolts are permitted on the inactive leaf Unlatching. The unlatching of any door or leaf shall not require more than one operation. 1. Places of detention or restraint.

6 2. Where manually operated bolt locks are permitted by Section Doors with automatic flush bolts as permitted by Section , Exception Doors from individual dwelling units and sleeping units of Group R occupancies as permitted by Section , Exception Delayed egress locks. Approved, listed, delayed egress locks shall be permitted to be installed on doors serving any occupancy except Group A, E and H occupancies in buildings that are equipped throughout with an automatic sprinkler system in accordance with Section or an approved automatic smoke or heat detection system installed in accordance with Section 907, provided that the doors unlock in accordance with Items 1 through 6 below. A building occupant shall not be required to pass through more than one door equipped with a delayed egress lock before entering an exit. 1. The doors unlock upon actuation of the automatic sprinkler system or automatic fire detection system. 2. The doors unlock upon loss of power controlling the lock or lock mechanism. 3. The door locks shall have the capability of being unlocked by a signal from the fire command center. 4. The initiation of an irreversible process which will release the latch in not more than 15 seconds when a force of not more than 15 pounds (67 N) is applied for 1 second to the release device. Initiation of the irreversible process shall activate an audible signal in the vicinity of the door. Once the door lock has been released by the application of force to the releasing device, relocking shall be by manual means only. Exception: Where approved, a delay of not more than 30 seconds is permitted. 5. A sign shall be provided on the door located above and within 12 inches (305 mm) of the release device reading: PUSH UNTIL ALARM SOUNDS. DOOR CAN BE OPENED IN 15 [30] SECONDS. 6. Emergency lighting shall be provided at the door Stairway doors. Interior stairway means of egress doors shall be openable from both sides without the use of a key or special knowledge or effort. 1. Stairway discharge doors shall be openable from the egress side and shall only be locked from the opposite side. 2. This section shall not apply to doors arranged in accordance with Section of the International Building Code. 3. In stairways serving not more than four stories, doors are permitted to be locked from the side opposite the egress side, provided they are openable from the egress side and capable of being unlocked simultaneously without unlatching upon a signal from the fire command center, if present, or a signal by emergency personnel from a single location inside the main entrance to the building Panic and fire exit hardware. Where panic and fire exit hardware is installed, it shall comply with the following: 1. The actuating portion of the releasing device shall extend at least one-half of the door leaf width. 2. The maximum unlatching force shall not exceed 15 pounds (67 N). Each door in a means of egress from a Group A or E occupancy having an occupant load of 50 or more and any Group H occupancy shall not be provided with a latch or lock unless it is panic hardware or fire exit hardware.

7 Exception: A main exit of a Group A occupancy in compliance with Section , Item 2. Electrical rooms with equipment rated 1,200 amperes or more and over 6 feet (1829 mm) wide that contain overcurrent devices, switching devices or control devices with exit access doors must be equipped with panic hardware and doors must swing in the direction of egress. If balanced doors are used and panic hardware is required, the panic hardware shall be the push-pad type and the pad shall not extend more than one-half the width of the door measured from the latch side. Unlock all exit doors during business hours. (IFC 2006 CHAPTER 10 MEANS OF EGRESS SEC ) Exit or exit access doorway arrangement. Required exits shall be located in a manner that makes their availability obvious. Exits shall be unobstructed at all times. Exit and exit access doorways shall be arranged in accordance with Sections and Two exits or exit access doorways. Where two exits or exit access doorways are required from any portion of the exit access, the exit doors or exit access doorways shall be placed a distance apart equal to not less than onehalf of the length of the maximum overall diagonal dimension of the building or area to be served measured in a straight line between exit doors or exit access doorways. Interlocking or scissor stairs shall be counted as one exit stairway. 1. Where exit enclosures are provided as a portion of the required exit and are interconnected by a 1-hour fire-resistance-rated corridor conforming to the requirements of Section 1017, the required exit separation shall be measured along the shortest direct line of travel within the corridor. 2. Where a building is equipped throughout with an automatic sprinkler system in accordance with Section or , the separation distance of the exit doors or exit access doorways shall not be less than one-third of the length of the maximum overall diagonal dimension of the area served Three or more exits or exit access doorways. Where access to three or more exits is required, at least two exit doors or exit access doorways shall be arranged in accordance with the provisions of Section EXIT LIGHTING Provide lighting for exits, aisles, corridors, and stairways. (IBC 2009 CHAPTER 10 MEANS OF EGRESS SEC 1006) SECTION 1006 MEANS OF EGRESS ILLUMINATION Illumination required. The means of egress, including the exit discharge, shall be illuminated at all times the building space served by the means of egress is occupied. 1. Occupancies in Group U. 2. Aisle accessways in Group A. 3. Dwelling units and sleeping units in Groups R-1, R-2 and R Sleeping units of Group I occupancies Illumination level. The means of egress illumination level shall not be less than 1 footcandle (11 lux) at the walking surface.

8 Exception: For auditoriums, theaters, concert or opera halls and similar assembly occupancies, the illumination at the walking surface is permitted to be reduced during performances to not less than 0.2 footcandle (2.15 lux), provided that the required illumination is automatically restored upon activation of a premises' fire alarm system where such system is provided Illumination emergency power. The power supply for means of egress illumination shall normally be provided by the premises' electrical supply. In the event of power supply failure, an emergency electrical system shall automatically illuminate all of the following areas: 1. Aisles and unenclosed egress stairways in rooms and spaces that require two or more means of egress. 2. Corridors, exit enclosures and exit passageways in buildings required to have two or more exits. 3. Exterior egress components at other than their levels of exit discharge until exit discharge is accomplished for buildings required to have two or more exits. 4. Interior exit discharge elements, as permitted in Section , in buildings required to have two or more exits. 5. Exterior landings as required by Section for exit discharge doorways in buildings required to have two or more exits. The emergency power system shall provide power for a duration of not less than 90 minutes and shall consist of storage batteries, unit equipment or an on-site generator. The installation of the emergency power system shall be in accordance with Chapter Performance of system. Emergency lighting facilities shall be arranged to provide initial illumination that is at least an average of 1 footcandle (11 lux) and a minimum at any point of 0.1 footcandle (1 lux) measured along the path of egress at floor level. Illumination levels shall be permitted to decline to 0.6 footcandle (6 lux) average and a minimum at any point of 0.06 footcandle (0.6 lux) at the end of the emergency lighting time duration. A maximum-to-minimum illumination uniformity ratio of 40 to 1 shall not be exceeded. Repair lighted exit signs or emergency lighting. (IFC 2006 CHAPTER 10 MEANS OF EGRESS SEC 1011) SECTION 1011 EXIT SIGNS Where required. Exits and exit access doors shall be marked by an approved exit sign readily visible from any direction of egress travel. The path of egress travel to exits and within exits shall be marked by readily visible exit signs to clearly indicate the direction of egress travel in cases where the exit or the path of egress travel is not immediately visible to the occupants. Intervening means of egress doors within exits shall be marked by exit signs. Exit sign placement shall be such that no point in an exit access corridor or exit passageway is more than 100 feet ( mm) or the listed viewing distance for the sign, whichever is less, from the nearest visible exit sign. 1. Exit signs are not required in rooms or areas that require only one exit or exit access. 2. Main exterior exit doors or gates that are obviously and clearly identifiable as exits need not have exit signs where approved by the building official. 3. Exit signs are not required in occupancies in Group U and individual sleeping units or dwelling units in Group R-1, R-2 or R-3.

9 4. Exit signs are not required in dayrooms, sleeping rooms or dormitories in occupancies in Group I In occupancies in Groups A-4 and A-5, exit signs are not required on the seating side of vomitories or openings into seating areas where exit signs are provided in the concourse that are readily apparent from the vomitories. Egress lighting is provided to identify each vomitory or opening within the seating area in an emergency Illumination. Exit signs shall be internally or externally illuminated. Exception: Tactile signs required by Section need not be provided with illumination Tactile exit signs. A tactile sign stating EXIT and complying with ICC A117.1 shall be provided adjacent to each door to an area of refuge, an exterior area for assisted rescue, an exit stairway, an exit ramp, an exit passageway and the exit discharge Internally illuminated exit signs. Electrically powered, self-luminous and photo-luminescent exit signs shall be listed and labeled in accordance with UL 924 and shall be installed in accordance with the manufacturer's instructions and Chapter 27. Exit signs shall be illuminated at all times Externally illuminated exit signs. Externally illuminated exit signs shall comply with Sections through Graphics. Every exit sign and directional exit sign shall have plainly legible letters not less than 6 inches (152 mm) high with the principal strokes of the letters not less than 3/4 inch (19.1 mm) wide. The word "EXIT" shall have letters having a width not less than 2 inches (51 mm) wide, except the letter "I," and the minimum spacing between letters shall not be less than 3/8 inch (9.5 mm). Signs larger than the minimum established in this section shall have letter widths, strokes and spacing in proportion to their height. The word "EXIT" shall be in high contrast with the background and shall be clearly discernible when the means of exit sign illumination is or is not energized. If a chevron directional indicator is provided as part of the exit sign, the construction shall be such that the direction of the chevron directional indicator cannot be readily changed Exit sign illumination. The face of an exit sign illuminated from an external source shall have an intensity of not less than 5 footcandles (54 lux) Power source. Exit signs shall be illuminated at all times. To ensure continued illumination for a duration of not less than 90 minutes in case of primary power loss, the sign illumination means shall be connected to an emergency power system provided from storage batteries, unit equipment or an on-site generator. The installation of the emergency power system shall be in accordance with Chapter 27. Exception: Approved exit sign illumination means that provide continuous illumination independent of external power sources for a duration of not less than 90 minutes, in case of primary power loss, are not required to be connected to an emergency electrical system.

10 FIRE EXTINGUISHERS Mount extinguishers where readily available, not more than 5-feet above floor. (IFC 2006 CHAPTER 9 FIRE PROTECTION SYSTEMS SEC 906.9) Post signs indicating location where extinguishers are not readily visible. (IFC 2006 CHAPTER 9 FIRE PROTECTION SYSTEMS SEC 906.6) Portable fire extinguishers are due for annual maintenance on (IFC 2006 CHAPTER 9 FIRE PROTECTION SYSTEMS SEC 906 & NFPA ): SECTION 906 PORTABLE FIRE EXTINGUISHERS Where required. Portable fire extinguishers shall be installed in the following locations. 1. In new and existing Group A, B, E, F, H, I, M, R-1, R-2, R-4 and S occupancies. Exception: In new and existing Group A, B and E occupancies equipped throughout with quickresponse sprinklers, portable fire extinguishers shall be required only in locations specified in Items 2 through Within 30 feet (9144 mm) of commercial cooking equipment. 3. In areas where flammable or combustible liquids are stored, used or dispensed. 4. On each floor of structures under construction, except Group R-3 occupancies, in accordance with Section Where required by the sections indicated in Table Special-hazard areas, including but not limited to laboratories, computer rooms and generator rooms, where required by the fire code official General requirements. Portable fire extinguishers shall be selected, installed and maintained in accordance with this section and NFPA The travel distance to reach an extinguisher shall not apply to the spectator seating portions of Group A-5 occupancies. 2. Thirty-day inspections shall not be required and maintenance shall be allowed to be once every three years for dry-chemical or halogenated agent portable fire extinguishers that are supervised by a listed and approved electronic monitoring device, provided that all of the following conditions are met: 2.1. Electronic monitoring shall confirm that extinguishers are properly positioned, properly charged and unobstructed Loss of power or circuit continuity to the electronic monitoring device shall initiate a trouble signal The extinguishers shall be installed inside of a building or cabinet in a noncorrosive environment Electronic monitoring devices and supervisory circuits shall be tested every three years when extinguisher maintenance is performed A written log of required hydrostatic test dates for extinguishers shall be maintained by the owner to ensure that hydrostatic tests are conducted at the frequency required by NFPA Size and distribution. For occupancies that involve primarily Class A fire hazards, the minimum sizes and distribution shall comply with Table 906.3(1). Fire extinguishers for occupancies involving flammable or combustible liquids with depths of less than or equal to 0.25-inch (6.35 mm) shall be selected and placed in accordance with Table 906.3(2). Fire extinguishers for occupancies involving flammable or combustible liquids with a depth of greater than 0.25-inch (6.35 mm) or involving

11 combustible metals shall be selected and placed in accordance with NFPA 10. Extinguishers for Class C fire hazards shall be selected and placed on the basis of the anticipated Class A or Class B hazard Cooking grease fires. Fire extinguishers provided for the protection of cooking grease fires shall be of an approved type compatible with the automatic fire-extinguishing system agent and in accordance with Section Conspicuous location. Portable fire extinguishers shall be located in conspicuous locations where they will be readily accessible and immediately available for use. These locations shall be along normal paths of travel, unless the fire code official determines that the hazard posed indicates the need for placement away from normal paths of travel Unobstructed and unobscured. Portable fire extinguishers shall not be obstructed or obscured from view. In rooms or areas in which visual obstruction cannot be completely avoided, means shall be provided to indicate the locations of extinguishers Hangers and brackets. Hand-held portable fire extinguishers, not housed in cabinets, shall be installed on the hangers or brackets supplied. Hangers or brackets shall be securely anchored to the mounting surface in accordance with the manufacturer s installation instructions Cabinets. Cabinets used to house portable fire extinguishers shall not be locked. 1. Where portable fire extinguishers subject to malicious use or damage are provided with a means of ready access. 2. In Group I-3 occupancies and in mental health areas in Group I-2 occupancies, access to portable fire extinguishers shall be permitted to be locked or to be located in staff locations provided the staff has keys. TABLE ADDITIONAL REQUIRED PORTABLE FIRE EXTINGUISHERS SECTION SUBJECT Asphalt kettles Open burning Open flames torches Powered industrial trucks Aircraft towing vehicles Aircraft welding apparatus Aircraft fuel-servicing tank vehicles Aircraft hydrant fuel-servicing vehicles Aircraft fuel-dispensing stations Heliports and helistops Dry cleaning plants Buildings under construction or demolition

12 Roofing operations Spray-finishing operations Dip-tank operations Powder-coating areas Lumberyards/woodworking facilities Recycling facilities Exterior lumber storage Organic-coating areas Industrial ovens Motor fuel-dispensing facilities Marine motor fuel-dispensing facilities Repair garages Rack storage Tents, canopies and membrane structures Tire rebuilding/storage Welding and other hot work Combustible fibers Fireworks Flammable and combustible liquids, general Indoor storage of flammable and combustible liquids Liquid storage rooms for flammable and combustible liquids Solvent distillation units Farms and construction sites flammable and combustible liquids storage Bulk plants and terminals for flammable and combustible liquids Commercial, industrial, governmental or manufacturing establishments fuel dispensing Tank vehicles for flammable and combustible liquids Flammable solids LP-gas TABLE 906.3(1) FIRE EXTINGUISHERS FOR CLASS A FIRE HAZARDS LIGHT (Low) HAZARD ORDINARY (Moderate) HAZARD OCCUPANCY EXTRA (High) HAZARD OCCUPANCY

13 Minimum Rated Single Extinguisher Maximum Floor Area Per Unit of A OCCUPANCY 2-A c 2-A 4-A a 3,000 square feet Maximum Floor Area For Extinguisher b 11,250 square feet Maximum Travel Distance to Extinguisher 1,500 square feet 11,250 square feet 1,000 square feet 11,250 square feet 75 feet 75 feet 75 feet For SI: 1 foot = mm, 1 square foot = m 2, 1 gallon = L. a. Two 2.5-gallon water-type extinguishers shall be deemed the equivalent of one 4-A rated extinguisher. b. Annex E.3.3 of NFPA 10 provides more details concerning application of the maximum floor area criteria. c. Two water-type extinguishers each with a 1-A rating shall be deemed the equivalent of one 2- A rated extinguisher for Light (Low) Hazard Occupancies. TABLE 906.3(2) FLAMMABLE OR COMBUSTIBLE LIQUIDS WITH DEPTHS OF LESS THAN OR EQUAL TO 0.25-INCH TYPE OF HAZARD BASIC MINIMUM EXTINGUISHER RATING Light (Low) 5-B MAXIMUM TRAVEL DISTANCE TO EXTINGUISHERS (feet) B Ordinary (Moderate) 10-B 20-B Extra (High) 40-B 80-B For SI: 1 inch = 25.4 mm, 1 foot = mm. NOTE. For requirements on water-soluble flammable liquids and alternative sizing criteria, see Section 4.3 of NFPA Height above floor. Portable fire extinguishers having a gross weight not exceeding 40 pounds (18 kg) shall be installed so that its top is not more than 5 feet (1524 mm) above the floor. Hand-held portable fire extinguishers having a gross weight exceeding 40 pounds (18 kg) shall be installed so that its

14 top is not more than 3.5 feet (1067 mm) above the floor. The clearance between the floor and the bottom of installed hand-held extinguishers shall not be less than 4 inches (102 mm) Wheeled units. Wheeled fire extinguishers shall be conspicuously located in a designated location. COMMERCIAL KITCHEN Portable K fire extinguishers located in kitchen. (IFC 2006 CHAPTER 9 FIRE PROTECTION SYSTEMS SEC ) Portable K/hood suppression system fire extinguishers are due for 6-month maintenance on (IFC 2006 CHAPTER 9 FIRE PROTECTION SYSTEMS SEC ) (mm/yy) : SECTION 904 ALTERNATIVE AUTOMATIC FIRE-EXTINGUISHING SYSTEMS Portable fire extinguishers for commercial cooking equipment. Portable fire extinguishers shall be provided within a 30-foot (9144 mm) travel distance of commercial-type cooking equipment. Cooking equipment involving vegetable or animal oils and fats shall be protected by a Class K rated portable extinguisher Portable fire extinguishers for solid fuel cooking appliances. All solid fuel cooking appliances, whether or not under a hood, with fireboxes 5 cubic feet (0.14 m3) or less in volume shall have a minimum 2.5-gallon (9 L) or two 1.5-gallon (6 L) Class K wetchemical portable fire extinguishers located in accordance with Section Class K portable fire extinguishers for deep fat fryers. When hazard areas include deep fat fryers, listed Class K portable fire extinguishers shall be provided as follows: 1. For up to four fryers having a maximum cooking medium capacity of 80 pounds (36.3 kg) each: One Class K portable fire extinguisher of a minimum 1.5 gallon ( 6 L) capacity. 2. For every additional group of four fryers having a maximum cooking medium capacity of 80 pounds (36.3 kg) each: One additional Class K portable fire extinguisher of a minimum 1.5 gallon (6 L) capacity shall be provided. 3. For individual fryers exceeding 6 square feet (0.55 m2) in surface area: Class K portable fire extinguishers shall be installed in accordance with the extinguisher manufacturer s recommendations Operations and maintenance. Commercial cooking systems shall be operated and maintained in accordance with this section Ventilation system. The ventilation system in connection with hoods shall be operated at the required rate of air movement, and classified grease filters shall be in place when equipment under a kitchen grease hood is used Grease extractors. Where grease extractors are installed, they shall be operated when the commercial-type cooking equipment is used Cleaning. Hoods, grease-removal devices, fans, ducts and other appurtenances shall be cleaned at intervals necessary to prevent the accumulation of grease. Cleanings shall be recorded, and records shall state the extent, time and date of cleaning. Such records shall be maintained on the premises Extinguishing system service. Automatic fire-extinguishing systems shall be serviced at least every 6 months and after activation of the system. Inspection shall be by qualified individuals, and a certificate of inspection shall be forwarded to the fire code official upon completion.

15 Fusible link and sprinkler head replacement. Fusible links and automatic sprinkler heads shall be replaced at least annually, and other protection devices shall be serviced or replaced in accordance with the manufacturer s instructions. Exception: Frangible bulbs are not required to be replaced annually. Exhaust hoods/ducts and grease filters will be installed, repaired and maintained to operate properly. (IFC 2006 CHAPTER 6 BUILDING SERVICES AND SYSTEMS SEC 609) SECTION 609 COMMERCIAL KITCHEN HOODS General. [M] Commercial kitchen exhaust hoods shall comply with the requirements of the International Mechanical Code Where required. [M] A Type I hood shall be installed at or above all commercial cooking appliances and domestic cooking appliances used for commercial purposes that produce grease vapors. Clean grease filters and hood/duct system over cooking equipment. (IFC 2006 CHAPTER 9 FIRE PROTECTION SYSTEMS SEC & ) Deep fryers will have the proper size Class K extinguisher available. (IFC 2006 CHAPTER 9 FIRE PROTECTION SYSTEMS SEC ) Install, repair and maintain the manual activation device for the fire extinguishing system. (IFC 2006 CHAPTER 9 FIRE PROTECTION SYSTEMS SEC ) FIRE PROTECTION ACCESS and EQUIPMENT Install approved protective covers on fire department hose connection. (IFC 2006 CHAPTER 9 FIRE PROTECTION SYSTEMS SEC ) SECTION 912 FIRE DEPARTMENT CONNECTIONS Installation. Fire department connections shall be installed in accordance with the NFPA standard applicable to the system design and shall comply with Sections through Location. With respect to hydrants, driveways, buildings and landscaping, fire department connections shall be so located that fire apparatus and hose connected to supply the system will not obstruct access to the buildings for other fire apparatus. The location of fire department connections shall be approved Visible location. Fire department connections shall be located on the street side of buildings, fully visible and recognizable from the street or nearest point of fire department vehicle access or as otherwise approved by the fire code official Existing buildings. On existing buildings, wherever the fire department connection is not visible to approaching fire apparatus, the fire department connection shall be indicated by an approved sign mounted on the street front or on the side of the building. Such sign shall have the letters FDC at least 6 inches (152 mm) high and words in letters at least 2 inches (51 mm) high or an arrow to indicate the location. All such signs shall be subject to the approval of the fire code official.

16 912.3 Access. Immediate access to fire department connections shall be maintained at all times and without obstruction by fences, bushes, trees, walls or any other object for a minimum of 3 feet (914 mm) Locking fire department connection caps. The fire code official is authorized to require locking caps on fire department connections for water-based fire protection systems where the responding fire department carries appropriate key wrenches for removal Signs. A metal sign with raised letters at least 1 inch (25 mm) in size shall be mounted on all fire department connections serving automatic sprinklers, standpipes or fire pump connections. Such signs shall read: AUTOMATIC SPRINKLERS or STANDPIPES or TEST CONNECTION or a combination thereof as applicable Backflow protection. The potable water supply to automatic sprinkler and standpipe systems shall be protected against backflow as required by the International Plumbing Code Inspection, testing and maintenance. All fire department connections shall be periodically inspected, tested and maintained in accordance with NFPA 25. Maintain access to and operation of standpipes, fire hose, sprinkler valves, fire hydrants, fire extinguishers, and other fire protection equipment. (IFC 2006 SEC CHAPTER 9 FIRE PROTECTION SYSTEMS 912.2) Provide and maintain smoke detectors and/or CO detectors in proper operating condition. (IFC 2006 CHAPTER 9 FIRE PROTECTION SYSTEMS SEC ) SECTION 907 FIRE ALARM AND DETECTION SYSTEMS Inspection, testing and maintenance. The maintenance and testing schedules and procedures for fire alarm and fire detection systems shall be in accordance with this section and Chapter 10 of NFPA Maintenance required. Whenever or wherever any device, equipment, system, condition, arrangement, level of protection or any other feature is required for compliance with the provisions of this code, such device, equipment, system, condition, arrangement, level of protection or other feature shall thereafter be continuously maintained in accordance with applicable NFPA requirements or as directed by the fire code official Testing. Testing shall be performed in accordance with the schedules in Chapter 10 of NFPA 72 or more frequently where required by the fire code official. Where automatic testing is performed at least weekly by a remotely monitored fire alarm control unit specifically listed for the application, the manual testing frequency shall be permitted to be extended to annual. Exception: Devices or equipment that are inaccessible for safety considerations shall be tested during scheduled shutdowns where approved by the fire code official, but not less than every 18 months Detector sensitivity. Detector sensitivity shall be checked within one year after installation and every alternate year thereafter. After the second calibration test, where sensitivity tests indicate that the detector has remained within its listed and marked sensitivity range (or 4-percent obscuration light grey smoke, if not marked), the length of time between calibration tests shall be permitted to be

17 extended to a maximum of five years. Where the frequency is extended, records of detectorcaused nuisance alarms and subsequent trends of these alarms shall be maintained. In zones or areas where nuisance alarms show any increase over the previous year, calibration tests shall be performed Method. To ensure that each smoke detector is within its listed and marked sensitivity range, it shall be tested using either a calibrated test method, the manufacturer s calibrated sensitivity test instrument, listed control equipment arranged for the purpose, a smoke detector/control unit arrangement whereby the detector causes a signal at the control unit where its sensitivity is outside its acceptable sensitivity range or other calibrated sensitivity test method acceptable to the fire code official. Detectors found to have a sensitivity outside the listed and marked sensitivity range shall be cleaned and recalibrated or replaced. 1. Detectors listed as field adjustable shall be permitted to be either adjusted within the listed and marked sensitivity range and cleaned and recalibrated or they shall be replaced. 2. This requirement shall not apply to single-station smoke alarms Testing device. Detector sensitivity shall not be tested or measured using a device that administers an unmeasured concentration of smoke or other aerosol into the detector Maintenance, inspection and testing. The building owner shall be responsible for ensuring that the fire and life safety systems are maintained in an operable condition at all times. Service personnel shall meet the qualification requirements of NFPA 72 for maintaining, inspecting and testing such systems. A written record shall be maintained and shall be made available to the fire code official. Provided minimum 4-inches high address numbers so they are visible from the street. (IFC 2006 CHAPTER 5 FIRE SERVICE FEATURES SEC 505.1) SECTION 505 PREMISES IDENTIFICATION Address numbers. New and existing buildings shall have approved address numbers, building numbers or approved building identification placed in a position that is plainly legible and visible from the street or road fronting the property. These numbers shall contrast with their background. Address numbers shall be Arabic numerals or alphabet letters. Numbers shall be a minimum of 4 inches (102 mm) high with a minimum stroke width of 0.5 inch (12.7 mm) Street or road signs. Streets and roads shall be identified with approved signs. Temporary signs shall be installed at each street intersection when construction of new roadways allows passage by vehicles. Signs shall be of an approved size, weather resistant and be maintained until replaced by permanent signs. Remove obstructions and provide access in fire lanes. (IFC 2006 CHAPTER 9 FIRE PROTECTION SYSTEMS SEC 912.2) The X system(s) is/are due for confidence testing and certification. Please see the attached report.