4" Touchscreen Shown - 5.5" Available

Transcription

1 Yale Assure Lock Electronic Interconnected Touchscreen Installation and Programming Instructions (YRC226/YRC426/YRC620) Inside of Door Outside of Door 4" Touchscreen Shown - 5.5" Available Before you begin DOWNLOAD THE BILT APP for step-by-step installation instructions & to register your product Network Module (Optional - Not available on YRC620) Retrofitting or modifying this product may impact fire rating, safety features and warranty. Consult with code specifications to ensure compliance with all codes and ratings. 1

2 Before You Begin Template Network Module (Optional - Not available on YRC620) 1/8" 3/32" #2 1 x2 x2 x2 x8 x1 x2 1/8" 1" 2-1/8" 4-1/2" (114) Min 1-3/8" (35mm) Min to 1-3/4" (44.5mm) Max 2

3 Mark Door Reference Lines EXISTING 2-3/8" or 2-3/4" Backset Template REMOVE C L 3

4 1 Preparing Door (if necessary) Template 4" or 5.5" Ø2-1/8" 2-3/8" or 2-3/4" Ø1"! Drill holes 1/2 way thru door then complete from other side to prevent splitting. 4

5 2 Installing Strike Plates 7-16 / 8-32 x 1" UNCWS Frame x4 Frame 1" Dia. x 1"Deep Inside of Door 1" Dia. x 1/2"Deep Door Frame 5

6 Determining Handing The hand of a door is determined from the secure side of the door. The term "secure" means the side from which you initially unlock and enter. Left Hand LH, Hinges Left. Open Inward. Left Hand Reverse " LHR", Hinges Left. Open Outward. Right Hand " RH", Hinges Right. Open Inward. Right Hand Reverse " RHR", Hinges Right. Open Outward. 6

7 3 Changing Handing (if necessary) 4" Left Hand to 4" Right Hand Shown 4-24 x 1/4" PPHMS x2! DO NOT TAMPER WITH OR LOOSEN E-CLIP AND ITS ASSEMBLY! DO NOT LOOSEN THESE 6 SCREWS OR REMOVE COVER 7

8 3 Changing Handing (if necessary) continued 8

9 Lockset Handing Configurations For 5.5" For 5.5" For 4" 4" Left Hand For 4" 4" Right Hand Test Lever and Thumbturn After handing is changed, check that lever and thumbturn rotate freely. 9

10 4 Installing Fire Cups Inside of Door! Both Fire Cups and a UL marked Latchbolt must be used to qualify for UL listing. 10

11 5 Adjusting Deadbolt Latch (If adjustable deadbolt latch provided) default 2-3/8" position UP O optional 2-3/4" position UP Pull Press 11

12 6 Installing Deadbolt Latch & Latchbolt 7-16 / 8-32 x 1" UNCWS x4 Inside of Door UP! Bolt must be in retracted (unlocked) position before installing.! Ensure arrow stamped on deadbolt is UP. Choose latchbolt based on backset. (2-3/8" or 2-3/4")! Curved edge of latchbolt faces direction door closes. 12

13 7 Installing Exterior Deadbolt M6x55 PPHMS UP! Bolt must be in retracted (unlocked) position. x2 Inside of Door UP 13

14 8 Installing Lock Chassis x 1-1/2" PPHMS Inside of Door x2 UP 14

15 9 Securing Back Plate to Door #6-32 x 1/2" POHMS x2 Inside of Door UP! Drill two pilot holes Ø1/8" x 1/2" deep! #6-32 x 1/2" POHMS screws must be used to qualify for UL listing. 15

16 Testing Deadbolt & Latchbolt Operation Outside of Door 16

17 10 Remove Battery Cover Loosen screw to remove cover. 17

18 11 Attaching the Cable Assembly Inside of Door! Align wire connectors so that tabs slide into slots. Tug gently on cables to test that connectors are secure. Slot Tab Slot Tab! Cable must be routed as shown to avoid interference with movement of lock. UP 18

19 12 Installing Interior Lock! Orientation must match. Do not fasten lock to back plate until properly fitted. Inside of Door! Turn thumbturn to adjust slot orientation. UP 19

20 12 Installing Interior Lock continued x 5/8" POHMS 6-32 x 1" PPHMS x1 x2 Inside of Door! DO NOT LOOSEN THIS SCREW 20

21 13 Installing Interior Lever Inside of Door " SNAP" Inside of Door Pull lever to ensure it is secure. 21

22 Testing Final Latchbolt Operation Inside of Door Outside of Door 22

23 Testing Final Deadbolt Operation! If testing fails, go back to beginning of Step 12 and check installation. 23

24 14 Installing Optional Network Module (Optional - Not available on YRC620)! DO NOT install network module with batteries in unit. Damage may occur. 15 Installing Batteries & Cover Tighten screw to replace cover. "Welcome to..."! Bolt must be in retracted (unlocked) position before installing batteries. 24

25 Handing the Lock AFTER installing batteries and cover or AFTER a factory reset, create Master PIN code. See 1 of Programming Instructions. After entering the Master PIN code: Press Advanced Lock Settings Press to Select Press Handing the Lock Press to Select Press to complete Lock will cycle motor to complete handing. Congratulations, you've installed the Yale Assure Lock Electronic Interconnected Touchscreen! Continue with the Programming Instructions to customize your product. 25

26 Hardware Troubleshooting Cycle lock in both the locked and unlocked positions. If problems are found: Bolt will not extend and motor is grinding a. Enter your Master PIN code. b. With the bolt retracted, press menu Option 3 for Advanced Lock Settings. c. Press Option 5 to rehand the lock. d. Test the operation; locking the door via the keypad. Door is binding a. Check that door and frame are properly aligned and door is free swinging. b. Check hinges: They should not be loose or have excessive wear on knuckles. Bolt will not deadlock a. Check for sufficient clearance of the bolt within the strike-side jamb. Correct this by increasing the depth of the pocket for the bolt. b. Check for misalignment of bolt and/or strike which may be preventing bolt from properly entering the strike. With the door open, extend and retract the bolt; if it is smooth, check the strike alignment. Bolt does not extend or retract smoothly a. Bolt and strike are misaligned, see above. b. Check the backset of door relative to adjustments already made to bolt. c. Verify proper door preparation and re-bore holes that are too small or misaligned. d. Verify touchscreen wire harness is routed properly (see Step 10). e. Verify bolt is installed with correct side up (see Step 6). Keypad numerics are scrolling Remove interior escutcheon: a. Check that wire terminals are securely connected. b. Check that wire harness lies flat against mounting plate and is routed through wire hook on mounting plate so cable is not pinched at any point. 26

27 Changing Lock: Replacing Cylinder To remove cylinder: A. Remove touchscreen from door. B. Remove pan head screw. C. Remove cylinder by letting it drop out of assembly. B C A Touchscreen shown removed from door. Resetting Lock to Factory Default When resetting the lock, all user codes, including the Master PIN code*, are deleted. All programming features are reset to original default settings (see below). Interior Lock (4" Shown) 1. Remove the battery cover and batteries. 2. Remove the interior lock to access the reset button hole. (See image at right.) 3. Re-insert 3 batteries and insert a small screwdriver into the hole; holding the reset button for 3 seconds. 4. While still holding the reset button, insert the 4th battery and hold the reset button for an additional 3 seconds. 5. Release the reset button. 6. Re-install the interior lock onto the door. Reset Button Access Upon reset, Master PIN Code creation is the only option available and must be performed prior to any other programming of the lock. For best results, the lock should be installed on the door when resetting the lock to factory default. If the process was done and the lock was not installed on the door, review the Re-Handing instructions listed in Hardware Troubleshooting. 27

28 Programming Instructions Touchscreen "P" Key (Return to Previous) Interior Lock Low Battery Indicator Lockout Mode Privacy Mode Button Speaker Lock Activation OR Master PIN Code must be created before any further programming. Max User Codes = 250 with Z-Wave Plus or ZigBee network module Max User Codes = 25 without network module or with im1 network module Max User Codes = 12 with Bluetooth 28

29 1 Creating Master PIN Code Creating a Master PIN Code must be performed upon installation or after resetting the lock to factory default. Programming and use of lock is not possible until this step has been successfully completed. "Register Master Code. Press the gear key to continue." Press Enter 4-8 digit Master PIN Code. "Enter a 4 to 8 digit PIN code followed by the gear key." "Entered." Press 29

30 2 Creating User PIN Codes Master PIN code must be created first. *Max user codes = 250 with Z-Wave or ZigBee network module Max user codes = 25 without network module or with im1 network module Max user codes = 12 with Bluetooth Enter Master PIN code Press "Menu Mode, enter number, press the gear key to continue." Press Press Press Press Enter 4-8 digit Press (code flashes) PIN code Adding more *User Codes: Press Enter 4-8 digit PIN code Press To end programming: Press 30

31 3 Unlocking Door with PIN Code Enter PIN Code Press Factory Settings Settings Master PIN Code Automatic Re-lock Inside Indicator Light One Touch Locking Privacy Button Setting Volume Setting Language Setting Lockout Mode Wrong Code Entry Limit Shutdown Time Factory Setting Registration required* Disabled Disabled (Off) Enabled Disabled Enabled (Low) English Disabled 5 Times 60 Seconds *The Master PIN code must be registered prior to any other programming of the lock. 31

32 Definitions All Code Lockout Mode: This feature is enabled by the Master code. When enabled, it restricts all user (except Master) PIN code access. When attempting to enter a code while the unit is in Lockout, the RED locked padlock will appear on the screen. Automatic Re-lock Time: After a successful unlock, the unit will re-lock automatically after duration selected in the Advanced Lock Settings (Main Menu selection #3). Handing the Lock: Lock handing refers to which direction the bolt comes out of the door (right or left). If the lock was programmed off the door, the lock may need adjusting. Review Handing the Lock instructions and/or Re- Handing instructions listed in Hardware Troubleshooting. Inside Indicator Light: Located on the interior lock. Shows active status (Locked) of lock and can be enabled or disabled in the Advanced Lock Settings (Main Menu selection #3). Language Setting Mode: Choosing English (1), Spanish (2) or French (3) becomes the (default) setting for the lock's voice prompts. Low Battery: When battery power is low, the Low Battery Warning indicator flashes RED. If battery power is completely lost, use the cylinder key override. Master PIN Code: The Master PIN code is used for programming and for feature settings. It must be created prior to programming the lock. The Master code will also operate (unlock/lock) the lock. Network Module Setting: With the optional Network Module installed, this setting becomes available thru the Main Menu (7) and allows the lock to connect with a network controller. One Touch Locking: When the latch is retracted, activating the keypad will extend the latch (during Automatic Relock duration or when Automatic Re-lock is disabled). When One-Touch Re-lock is not in use (disabled), any valid PIN code will re-lock the lock. Previous: While in Menu Mode, pressing this icon cancels the current operation and returns the user to the previous step. Privacy Mode: Privacy mode is disabled by default. Enable Privacy Mode by pressing the privacy button for 4 seconds to put the lock in do-not-disturb mode (all pin codes are disabled). Shutdown Time: The unit will shutdown (flashing RED) for sixty (60) seconds and not allow operation after the wrong code entry limit (5 attempts) has been met. Tamper Alert: Audible alarm sounds if attempting to forcibly remove outside lock from door. User PIN Code: The User code operates the lock. Maximum number of user codes with Z-Wave Plus or ZigBee network module is 250; without network module or with im1 network module, maximum is 25; with Bluetooth, maximum is 12. Note: When deleting user pin code(s), screen will display user pin code being deleted. Volume Setting Mode: The volume setting for PIN code verification is set to Low (2) by default; otherwise it can be set to High (1) or Silent (3) for quiet areas. Wrong Code Entry Limit: After five (5) unsuccessful attempts at entering a valid PIN code, the unit will shut down and not allow operation for sixty (60) seconds. 32

33 Model YRC226 Feature Programming Through Menu Mode Using Master PIN code* 1. Touch screen with back of hand or palm to activate. 2. Enter 4-8 digit master PIN code* followed by key. Lock Response: "Menu mode, enter number, press key to continue." 3. Enter digit corresponding to the function to be performed followed by the key. Follow the voice commands. *The Master PIN code must be registered prior to any other programming of the lock. M Master PIN Code Setting M User PIN Code Registration Register U Continue Complete Continue Delete Complete Continue Complete Advanced Lock Settings Automatic Re-lock Disable 30 sec 60 sec 2 min 3 min Inside Indicator Light Enable Disable Continue One Touch Locking Enable Disable Privacy Setting Mode Enable Disable Handing the Lock Preforms automatic handing of the lock Complete Volume Setting High Low Silent Language Setting Mode Lockout Mode **Network Module Setting English Spanish French Enable Disable Join the Network Exit the Network Default settings in bold. **This function appears only with network module installed. 33

34 Model YRC620 Feature Programming Through Menu Mode Using Master PIN code* 1. Touch screen with back of hand or palm to activate. 2. Enter 4-8 digit master PIN code* followed by key. Lock Response: "Menu mode, enter number, press key to continue." 3. Enter digit corresponding to the function to be performed followed by the key. Follow the voice commands. *The Master PIN code must be registered prior to any other programming of the lock. M Master PIN Code Setting M User PIN Code Registration Register U Continue Complete Continue Delete Complete Continue Complete Advanced Lock Settings *Automatic Re-lock Enable Enter Time Sec Disable Inside Indicator Light Enable One Touch Locking Disable Enable Continue Disable Privacy Setting Mode Enable Disable Handing the Lock Preforms automatic handing of the lock Complete *Escape Return Mode Enable Disable Continue Volume Setting Language Setting Mode Lockout Mode Set Up SEOS Card High Low Silent English Spanish French Enable Disable Default settings in bold. Complete *If Escape Return Mode is enabled, Automatic Re-lock cannot be enabled. 34

35 Programming Troubleshooting Symptom Suggested Action 35

36 FCC: Class B Equipment This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful Interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/ TV technician for help. Warning: Changes or modifications to this device, not expressly approved by Yale Security Inc. could void the user's authority to operate the equipment. Industry Canada: This Class A digital apparatus meets all requirements of the Canadian Interference Causing Equipment Regulations. Cet appareillage numérique de la classe A répond à toutes les exigences de l'interférence canadienne causant des règlements d'équipement. Product Support Tel Yale,Yale Real Living and Assure Lock are registered trademarks of Assa Abloy Residential Group. Other products' brand names may be trademarks or registered trademarks of their respective owners and are mentioned for reference purposes only. Copyright All rights reserved. Reproduction in whole or in part without the express written permission of Assa Abloy Residential Group is prohibited. 36

37 Yale Z-Wave Plus Module Installation and Programming Instructions Installing the Z-Wave Plus Module IMPORTANT: the batteries must be removed prior to removing and/or inserting the network module: Remove battery cover and batteries. Remove and/or insert Network Module. Reinstall batteries and battery cover. Enrolling/Unenrolling the Network Module: This device is a security enabled Z-Wave Plus product that is able to use encrypted Z-Wave Plus messages to communicate to other security enabled Z-Wave Plus products. This device must be used in conjunction with a Security Enabled Z-Wave Controller in order to fully utilize all implemented functions. This product can be operated in any Z-Wave network with other Z-Wave certified devices from other manufacturers. All non-battery operated nodes within the network will act as repeaters regardless of vendor to increase reliability of the network. To Enroll/Add the Module (Inclusion Mode): Enter the 4-8 digit Master PIN code followed by the key. Press the key followed by the key. Press the key followed by the key. To Unenroll/Remove the Module (Exclusion Mode): Enter the 4-8 digit Master PIN code followed by the key. Press the key followed by the key. Press the key followed by the key. Factory Reset - If No Controller: See the Lock Installation Manual Please use this procedure only when the network primary controller is missing or otherwise inoperable. For System Integrators: Specific Z-Wave Plus association and parameter information for your lock is available at YaleHome.com/ZwavePlus. P/N AYR202-ZW-INSTAL-FUL Rev D

38 ! Warning: Changes or modifications to this device, not expressly approved by Yale Security Inc. could void the user's authority to operate the equipment. FCC: Contain FCC ID: U4A-YRHCPZW 0FM Model: YRMZW2-US This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful Interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/tv technician for help. THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS. (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION. Industry Canada: Contain IC: 6982A-YRHCPZW 0FM Model: YRMZW2-US Section of RSS-GEN Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication. En vertu des règlements d'industrie Canada, cet émetteur radio ne peut fonctionner avec une antenne d'un type et un maximum (ou moins) approuvés pour gagner de l'émetteur par Industrie Canada. Pour réduire le risque d'interférence aux autres utilisateurs, le type d'antenne et son gain doivent être choisies de façon que la puissance isotrope rayonnée équivalente ( PIRE) ne dépasse pas ce qui est nécessaire pour une communication réussie. Section of RSS-GEN This Device complies with Industry Canada License-exempt RSS standard(s). Operation is subject to the following two conditions: 1) this device may not cause interference, and 2) this device must accept any interference, including interference that may cause undesired operation of the device. Cet appareil est conforme avec Industrie Canada RSS standard exemptes de licence(s). Son fonctionnement est soumis aux deux conditions suivantes: 1) ce dispositif ne peut causer des interférences, et 2) cet appareil doit accepter toute interférence, y compris les interférences qui peuvent causer un mauvais fonctionnement du dispositif. This radio transmitter 6982A-YRHCPZW 0FM has been approved by Industry Canada to operate with the antenna types listed below with the maximum permissible gain indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device. Le présent émetteur radio 6982A-YRHCPZW 0FM a été approuvé par Industrie Canada pour fonctionner avec les types d'antenne énumérés ci-dessous et ayant un gain admissible maximal. Les types d'antenne non inclus dans cette liste, et dont le gain est supérieur au gain maximal indiqué, sont strictement interdits pour l'exploitation de l'émetteur. CAN ICES-3B/ NMB-3B Product Support Tel Yale Locks & Hardware is a division of Yale Security Inc., an ASSA ABLOY Group company. Yale and Yale Real Living are registered trademarks of Yale Security Inc., an ASSA ABLOY Group Company. Other products brand names may be trademarks or registered trademarks of their respective owners and are mentioned for reference purposes only. Copyright 2017, Yale Security Inc., an ASSA ABLOY Group company. All rights reserved. Reproduction in whole or in part without the express written permission of Yale Security Inc. is prohibited. YALE, with its unique global reach and range of products, is the world's favorite lock the preferred solution for securing your home, family and personal belongings. ASSA ABLOY is the global leader in door opening solutions, dedicated to satisfying end-user needs for security, safety and convenience.

39 Yale ZigBee Module Installation and Programming Instructions Installing the ZigBee Module IMPORTANT: the batteries must be removed prior to removing and/or inserting the network module: Remove battery cover. Remove batteries. Remove and/or insert network module. Reinstall batteries. Replace cover. Enrolling/Unenrolling the Network Module: This device is a security enabled ZigBee product that is able to use encrypted ZigBee messages to communicate to other security enabled ZigBee products. This device must be used in conjunction with a Security Enabled ZigBee Controller in order to fully utilize all implemented functions. This product can be operated in any ZigBee network with other ZigBee certified devices from other manufacturers. All non-battery operated nodes within the network will act as repeaters regardless of vendor to increase reliability of the network. To Enroll the Module (Inclusion Mode): Enter the 4-8 digit Master PIN code followed by the key. Press the key followed by the key. Press the key followed by the key. To Unenroll the Module (Exclusion Mode): Enter the 4-8 digit Master PIN code followed by the key. Press the key followed by the key. Press the key followed by the key. P/N AYR202-ZB-INSTAL-FUL Rev C

40 FCC: FCC ID: U4A-YRHCPZB 0FM Model: YRMZB2 This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful Interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/ TV technician for help. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by manufacturer could void the user s authority to operate the equipment. IMPORTANT! Any changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate this equipment. Industry Canada: IC: 6982A-YRHCPZB 0FM Model: YRMZB2 This Device complies with Industry Canada License-exempt RSS standard(s). Operation is subject to the following two conditions: 1) this device may not cause interference, and 2) this device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d'industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes: (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, meme si le brouillage est susceptible d'en compromettre le fonctionnement. Important Note: Radiation Exposure Statement: This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body. Note Importante: (Pour l utilisation de dispositifs mobiles) Declaration d exposition aus radiations: Cet équipement est conforme aux limites d exposition aux rayonnements IC établies pour un environnement non contrôlé. Cet équipment doit être installé et utilisé avec un mimimum de 20 cm de distance entre la source de rayonnement et votre corps. IMPORTANT! Any changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate this equipment. IMPORTANT! Tous les changements ou modifications pas expressément approuvés par la partie responsable de la conformité ont pu vider l autorité de l utilisateur pour actioner cet équipment. CAN ICES-3B/ NMB-3B Product Support Tel Yale Locks & Hardware is a division of Yale Security Inc., an ASSA ABLOY Group company. Yale and Yale Real Living are registered trademarks of Yale Security Inc., an ASSA ABLOY Group Company. Other products brand names may be trademarks or registered trademarks of their respective owners and are mentioned for reference purposes only. Copyright 2017, Yale Security Inc., an ASSA ABLOY Group company. All rights reserved. Reproduction in whole or in part without the express written permission of Yale Security Inc. is prohibited. YALE, with its unique global reach and range of products, is the world's favorite lock the preferred solution for securing your home, family and personal belongings. ASSA ABLOY is the global leader in door opening solutions, dedicated to satisfying end-user needs for security, safety and convenience.

41 Yale im1 Network Module Installation and Programming Instructions Installing the Yale im1 Network Module IMPORTANT: the batteries must be removed prior to removing and/or inserting the network module: Remove battery cover and batteries. Remove and/or insert Network Module. Reinstall batteries and battery cover. Enrolling the im1 Network Module: The Yale im1 Network Module must be used with a Yale Assure Lock or Yale nextouch Lock and cannot be used in conjunction with any other Yale Network Module. To Enroll the Module: Enter the 4-8 digit Master PIN code followed by the key. Press the key followed by the key. Press the key followed by the key. P/N AYR202-iM1-INSTAL-FUL Rev C

42 Yale Secure App Connection with Yale im1 Network Module Connecting the Yale Secure App with the Yale im1 Network Module 1. After following the steps listed on other side of page for enrolling the module, download the Yale Secure app from the App Store. 2. Ensure Bluetooth is enabled on your iphone, ipad or ipod touch, and that you're within a foot of your Yale lock. 3. Open the Yale Secure app and agree to allow the app to access your Home Data. 4. If you do not have a home already created, create a new home when prompted. Tap + to add a new Yale Lock. 5. The app will search for your Yale Lock. Be sure that you are within close proximity (less than two feet or so). When "Yale Lock" appears, tap to add. *If the lock does not appear, enter your Master Pin Code on the lock keypad, tap the gear, tap 7, tap gear, tap 1 and then tap gear. 6. Scan your Accessory Setup Code; shown below, or manually enter within the app. Accessory Setup Code Product Support Tel Yale Locks & Hardware is a division of Yale Security Inc., an ASSA ABLOY Group company. Yale, Yale Real Living and Assure Lock are registered trademarks of Yale Security Inc., an ASSA ABLOY Group Company. nextouch is a trademark of Yale Security Inc., an ASSA ABLOY Group Company. Other products brand names may be trademarks or registered trademarks of their respective owners and are mentioned for reference purposes only. Copyright 2017, Yale Security Inc., an ASSA ABLOY Group Company. All rights reserved. Reproduction in whole or in part without the express written permission of Yale Security Inc. is prohibited. Apple, iphone, ipad, ipod touch and Siri are trademarks of Apple Inc., registered in the U.S. and other countries. HomeKit is a trademark of Apple Inc. Use of the Works with Apple HomeKit logo means that an electronic accessory has been designed to connect specifically to ipod touch, iphone or ipad, respectively, and has been certified by the developer to meet Apple performance standards. Apple is not responsible for the operation of this device or its compliance with safety and regulatory standards. Use of the HomeKit logo means that an electronic accessory has been designed to connect specifically to ipod, iphone, or ipad, respectively, and has been certified by the developer to meet Apple performance standards. Apple is not responsible for the operation of this device or its compliance with safety and regulatory standards. Please note that the use of this accessory with ipod, iphone, or ipad may affect wireless performance. YALE, with its unique global reach and range of products, is the world's favorite lock the preferred solution for securing your home, family and personal belongings. ASSA ABLOY is the global leader in door opening solutions, dedicated to satisfying end-user needs for security, safety and convenience.